[PATCH v3 0/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[PATCH v3 0/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Hans de Goede]

Hi All,

Here is v3 of the patch series to add support for the LED controller
on Intel Cherry Trail Whiskey Cove PMICs.

Changes in v3:
- Some comment tweaks and s/LED_OFF/0/ and s/LED_ON/1/
- Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
  is connected to a haptic feedback motor there (and LED2 is unused)

Changes in v2 (of my version of this):
- Address Pavel's small remarks on patch 1/5,
  see patch 1/5's commit message for details
- Improve/extend pattern docs in Documentation/leds/leds-cht-wcove.rst

This is based on the original patch for this from Yauhen Kharuzhy,
with additional work on top by me.

This addresses the review remarks on the v2 posting from Yauhen:
- Since the PMIC is connected to the battery any changes we make to
  the LED settings are permanent, even surviving reboot / poweroff.
  Save LED1 register settings on probe() and if auto-/hw-control was
  enabled on probe() restore the settings on remove() and shutdown().
- Add support for the pattern trigger to select breathing mode

This makes the charging LED on devices with these PMICs properly
reflect the charging status (this relies on sw control on most
devices) and this also allows control of the LED behind the pen
(digitizer on) symbol on the keyboard half of the Lenovo Yoga Book
1 models.

Regards,

Hans


Hans de Goede (4):
  leds: cht-wcove: Add suspend/resume handling
  leds: cht-wcove: Add support for breathing mode use hw_pattern sysfs
    API
  leds: cht-wcove: Set default trigger for charging LED
  leds: cht-wcove: Use breathing when LED_INIT_DEFAULT_TRIGGER is set

Yauhen Kharuzhy (1):
  leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

 Documentation/leds/index.rst           |   1 +
 Documentation/leds/leds-cht-wcove.rst  |  38 ++
 Documentation/leds/well-known-leds.txt |   2 +-
 drivers/leds/Kconfig                   |  11 +
 drivers/leds/Makefile                  |   1 +
 drivers/leds/leds-cht-wcove.c          | 477 +++++++++++++++++++++++++
 6 files changed, 529 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/leds/leds-cht-wcove.rst
 create mode 100644 drivers/leds/leds-cht-wcove.c

-- 
2.39.2

[PATCH v3 1/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Hans de Goede]

From: Yauhen Kharuzhy <jekhor@gmail.com>

Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
is implemented, breathing is not.

This driver was tested with Lenovo Yoga Book notebook.

Changes by Hans de Goede (in response to review of v2):
- Since the PMIC is connected to the battery any changes we make to
  the LED settings are permanent, even surviving reboot / poweroff.
  Save LED1 register settings on probe() and if auto-/hw-control was
  enabled on probe() restore the settings on remove() and shutdown().
- Delay switching LED1 to software control mode to first brightness write.
- Use dynamically allocated drvdata instead of a global drvdata variable.
- Ensure the LED is on when activating blinking.
- Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).

Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v3:
- Some comment tweaks and s/LED_OFF/0/
- Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
  is connected to a haptic feedback motor there (and LED2 is unused)

Changes in v2:
- Update comment about YB1 kernel source usage for register info
- Replace "cht-wc::" LED name prefix with "platform::"
- Add leds-cht-wcove to list of drivers using "platform::charging" in
  Documentation/leds/well-known-leds.txt
- Bail from cht_wc_leds_brightness_set() on first error
- Make default blink 1Hz, like sw-blink default blink
---
 Documentation/leds/well-known-leds.txt |   2 +-
 drivers/leds/Kconfig                   |  11 +
 drivers/leds/Makefile                  |   1 +
 drivers/leds/leds-cht-wcove.c          | 380 +++++++++++++++++++++++++
 4 files changed, 393 insertions(+), 1 deletion(-)
 create mode 100644 drivers/leds/leds-cht-wcove.c

diff --git a/Documentation/leds/well-known-leds.txt b/Documentation/leds/well-known-leds.txt
index 2160382c86be..7640debee6c0 100644
--- a/Documentation/leds/well-known-leds.txt
+++ b/Documentation/leds/well-known-leds.txt
@@ -65,7 +65,7 @@ Phones usually have multi-color status LED.
 
 * Power management
 
-Good: "platform:*:charging" (allwinner sun50i)
+Good: "platform:*:charging" (allwinner sun50i, leds-cht-wcove)
 
 * Screen
 
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 9dbce09eabac..90835716f14a 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -122,6 +122,17 @@ config LEDS_BCM6358
 	  This option enables support for LEDs connected to the BCM6358
 	  LED HW controller accessed via MMIO registers.
 
+config LEDS_CHT_WCOVE
+	tristate "LED support for Intel Cherry Trail Whiskey Cove PMIC"
+	depends on LEDS_CLASS
+	depends on INTEL_SOC_PMIC_CHTWC
+	help
+	  This option enables support for charger and general purpose LEDs
+	  connected to the Intel Cherrytrail Whiskey Cove PMIC.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called leds-cht-wcove.
+
 config LEDS_CPCAP
 	tristate "LED Support for Motorola CPCAP"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index d30395d11fd8..78b5b69f9c54 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_LEDS_BCM6328)		+= leds-bcm6328.o
 obj-$(CONFIG_LEDS_BCM6358)		+= leds-bcm6358.o
 obj-$(CONFIG_LEDS_BD2802)		+= leds-bd2802.o
 obj-$(CONFIG_LEDS_BLINKM)		+= leds-blinkm.o
+obj-$(CONFIG_LEDS_CHT_WCOVE)		+= leds-cht-wcove.o
 obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
 obj-$(CONFIG_LEDS_COBALT_QUBE)		+= leds-cobalt-qube.o
 obj-$(CONFIG_LEDS_COBALT_RAQ)		+= leds-cobalt-raq.o
diff --git a/drivers/leds/leds-cht-wcove.c b/drivers/leds/leds-cht-wcove.c
new file mode 100644
index 000000000000..9fe76a0c62c8
--- /dev/null
+++ b/drivers/leds/leds-cht-wcove.c
@@ -0,0 +1,380 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for LEDs connected to the Intel Cherry Trail Whiskey Cove PMIC
+ *
+ * Copyright 2019 Yauhen Kharuzhy <jekhor@gmail.com>
+ * Copyright 2023 Hans de Goede <hansg@kernel.org>
+ *
+ * Register info comes from the Lenovo Yoga Book Android opensource code
+ * available from Lenovo. File lenovo_yb1_x90f_l_osc_201803.7z path in the 7z:
+ * YB1_source_code/kernel/cht/drivers/misc/charger_gp_led.c
+ */
+
+#include <linux/kernel.h>
+#include <linux/leds.h>
+#include <linux/mfd/intel_soc_pmic.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define CHT_WC_LED1_CTRL		0x5e1f
+#define CHT_WC_LED1_FSM			0x5e20
+#define CHT_WC_LED1_PWM			0x5e21
+
+#define CHT_WC_LED2_CTRL		0x4fdf
+#define CHT_WC_LED2_FSM			0x4fe0
+#define CHT_WC_LED2_PWM			0x4fe1
+
+#define CHT_WC_LED1_SWCTL		BIT(0)		/* HW or SW control of charging led */
+#define CHT_WC_LED1_ON			BIT(1)
+
+#define CHT_WC_LED2_ON			BIT(0)
+#define CHT_WC_LED_I_MA2_5		(2 << 2)	/* LED current limit */
+#define CHT_WC_LED_I_MASK		GENMASK(3, 2)	/* LED current limit mask */
+
+#define CHT_WC_LED_F_1_4_HZ		(0 << 4)
+#define CHT_WC_LED_F_1_2_HZ		(1 << 4)
+#define CHT_WC_LED_F_1_HZ		(2 << 4)
+#define CHT_WC_LED_F_2_HZ		(3 << 4)
+#define CHT_WC_LED_F_MASK		GENMASK(5, 4)
+
+#define CHT_WC_LED_EFF_OFF		(0 << 1)
+#define CHT_WC_LED_EFF_ON		(1 << 1)
+#define CHT_WC_LED_EFF_BLINKING		(2 << 1)
+#define CHT_WC_LED_EFF_BREATHING	(3 << 1)
+#define CHT_WC_LED_EFF_MASK		GENMASK(2, 1)
+
+#define CHT_WC_LED_COUNT		2
+
+struct cht_wc_led_regs {
+	/* Register addresses */
+	u16 ctrl;
+	u16 fsm;
+	u16 pwm;
+	/* Mask + values for turning the LED on/off */
+	u8 on_off_mask;
+	u8 on_val;
+	u8 off_val;
+};
+
+struct cht_wc_led_saved_regs {
+	unsigned int ctrl;
+	unsigned int fsm;
+	unsigned int pwm;
+};
+
+struct cht_wc_led {
+	struct led_classdev cdev;
+	const struct cht_wc_led_regs *regs;
+	struct regmap *regmap;
+	struct mutex mutex;
+};
+
+struct cht_wc_leds {
+	struct cht_wc_led leds[CHT_WC_LED_COUNT];
+	/* Saved LED1 initial register values */
+	struct cht_wc_led_saved_regs led1_initial_regs;
+};
+
+static const struct cht_wc_led_regs cht_wc_led_regs[CHT_WC_LED_COUNT] = {
+	{
+		.ctrl		= CHT_WC_LED1_CTRL,
+		.fsm		= CHT_WC_LED1_FSM,
+		.pwm		= CHT_WC_LED1_PWM,
+		.on_off_mask	= CHT_WC_LED1_SWCTL | CHT_WC_LED1_ON,
+		.on_val		= CHT_WC_LED1_SWCTL | CHT_WC_LED1_ON,
+		.off_val	= CHT_WC_LED1_SWCTL,
+	},
+	{
+		.ctrl		= CHT_WC_LED2_CTRL,
+		.fsm		= CHT_WC_LED2_FSM,
+		.pwm		= CHT_WC_LED2_PWM,
+		.on_off_mask	= CHT_WC_LED2_ON,
+		.on_val		= CHT_WC_LED2_ON,
+		.off_val	= 0,
+	},
+};
+
+static const char * const cht_wc_leds_names[CHT_WC_LED_COUNT] = {
+	"platform::" LED_FUNCTION_CHARGING,
+	"platform::" LED_FUNCTION_INDICATOR,
+};
+
+static int cht_wc_leds_brightness_set(struct led_classdev *cdev,
+				      enum led_brightness value)
+{
+	struct cht_wc_led *led = container_of(cdev, struct cht_wc_led, cdev);
+	int ret;
+
+	mutex_lock(&led->mutex);
+
+	if (!value) {
+		ret = regmap_update_bits(led->regmap, led->regs->ctrl,
+					 led->regs->on_off_mask, led->regs->off_val);
+		if (ret < 0) {
+			dev_err(cdev->dev, "Failed to turn off: %d\n", ret);
+			goto out;
+		}
+
+		/* Disable HW blinking */
+		ret = regmap_update_bits(led->regmap, led->regs->fsm,
+					 CHT_WC_LED_EFF_MASK, CHT_WC_LED_EFF_ON);
+		if (ret < 0)
+			dev_err(cdev->dev, "Failed to update LED FSM reg: %d\n", ret);
+	} else {
+		ret = regmap_write(led->regmap, led->regs->pwm, value);
+		if (ret < 0) {
+			dev_err(cdev->dev, "Failed to set brightness: %d\n", ret);
+			goto out;
+		}
+
+		ret = regmap_update_bits(led->regmap, led->regs->ctrl,
+					 led->regs->on_off_mask, led->regs->on_val);
+		if (ret < 0)
+			dev_err(cdev->dev, "Failed to turn on: %d\n", ret);
+	}
+out:
+	mutex_unlock(&led->mutex);
+	return ret;
+}
+
+enum led_brightness cht_wc_leds_brightness_get(struct led_classdev *cdev)
+{
+	struct cht_wc_led *led = container_of(cdev, struct cht_wc_led, cdev);
+	unsigned int val;
+	int ret;
+
+	mutex_lock(&led->mutex);
+
+	ret = regmap_read(led->regmap, led->regs->ctrl, &val);
+	if (ret < 0) {
+		dev_err(cdev->dev, "Failed to read LED CTRL reg: %d\n", ret);
+		ret = 0;
+		goto done;
+	}
+
+	val &= led->regs->on_off_mask;
+	if (val != led->regs->on_val) {
+		ret = 0;
+		goto done;
+	}
+
+	ret = regmap_read(led->regmap, led->regs->pwm, &val);
+	if (ret < 0) {
+		dev_err(cdev->dev, "Failed to read LED PWM reg: %d\n", ret);
+		ret = 0;
+		goto done;
+	}
+
+	ret = val;
+done:
+	mutex_unlock(&led->mutex);
+
+	return ret;
+}
+
+/* Return blinking period for given CTRL reg value */
+static unsigned long cht_wc_leds_get_period(int ctrl)
+{
+	ctrl &= CHT_WC_LED_F_MASK;
+
+	switch (ctrl) {
+	case CHT_WC_LED_F_1_4_HZ:
+		return 1000 * 4;
+	case CHT_WC_LED_F_1_2_HZ:
+		return 1000 * 2;
+	case CHT_WC_LED_F_1_HZ:
+		return 1000;
+	case CHT_WC_LED_F_2_HZ:
+		return 1000 / 2;
+	};
+
+	return 0;
+}
+
+/*
+ * Find suitable hardware blink mode for given period.
+ * period < 750 ms - select 2 HZ
+ * 750 ms <= period < 1500 ms - select 1 HZ
+ * 1500 ms <= period < 3000 ms - select 1/2 HZ
+ * 3000 ms <= period < 5000 ms - select 1/4 HZ
+ * 5000 ms <= period - return -1
+ */
+static int cht_wc_leds_find_freq(unsigned long period)
+{
+	if (period < 750)
+		return CHT_WC_LED_F_2_HZ;
+	else if (period < 1500)
+		return CHT_WC_LED_F_1_HZ;
+	else if (period < 3000)
+		return CHT_WC_LED_F_1_2_HZ;
+	else if (period < 5000)
+		return CHT_WC_LED_F_1_4_HZ;
+	else
+		return -1;
+}
+
+static int cht_wc_leds_blink_set(struct led_classdev *cdev,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	struct cht_wc_led *led = container_of(cdev, struct cht_wc_led, cdev);
+	unsigned int ctrl;
+	int ret;
+
+	mutex_lock(&led->mutex);
+
+	/* Blink with 1 Hz as default if nothing specified */
+	if (!*delay_on && !*delay_off)
+		*delay_on = *delay_off = 500;
+
+	ctrl = cht_wc_leds_find_freq(*delay_on + *delay_off);
+	if (ctrl < 0) {
+		/* Disable HW blinking */
+		ret = regmap_update_bits(led->regmap, led->regs->fsm,
+					 CHT_WC_LED_EFF_MASK, CHT_WC_LED_EFF_ON);
+		if (ret < 0)
+			dev_err(cdev->dev, "Failed to update LED FSM reg: %d\n", ret);
+
+		/* Fallback to software timer */
+		*delay_on = *delay_off = 0;
+		ret = -EINVAL;
+		goto done;
+	}
+
+	ret = regmap_update_bits(led->regmap, led->regs->fsm,
+				 CHT_WC_LED_EFF_MASK, CHT_WC_LED_EFF_BLINKING);
+	if (ret < 0)
+		dev_err(cdev->dev, "Failed to update LED FSM reg: %d\n", ret);
+
+	/* Set the frequency and make sure the LED is on */
+	ret = regmap_update_bits(led->regmap, led->regs->ctrl,
+				 CHT_WC_LED_F_MASK | led->regs->on_off_mask,
+				 ctrl | led->regs->on_val);
+	if (ret < 0)
+		dev_err(cdev->dev, "Failed to update LED CTRL reg: %d\n", ret);
+
+	*delay_off = *delay_on = cht_wc_leds_get_period(ctrl) / 2;
+
+done:
+	mutex_unlock(&led->mutex);
+
+	return ret;
+}
+
+static int cht_wc_led_save_regs(struct cht_wc_led *led,
+				struct cht_wc_led_saved_regs *saved_regs)
+{
+	int ret;
+
+	ret = regmap_read(led->regmap, led->regs->ctrl, &saved_regs->ctrl);
+	if (ret < 0)
+		return ret;
+
+	ret = regmap_read(led->regmap, led->regs->fsm, &saved_regs->fsm);
+	if (ret < 0)
+		return ret;
+
+	return regmap_read(led->regmap, led->regs->pwm, &saved_regs->pwm);
+}
+
+static void cht_wc_led_restore_regs(struct cht_wc_led *led,
+				    const struct cht_wc_led_saved_regs *saved_regs)
+{
+	regmap_write(led->regmap, led->regs->ctrl, saved_regs->ctrl);
+	regmap_write(led->regmap, led->regs->fsm, saved_regs->fsm);
+	regmap_write(led->regmap, led->regs->pwm, saved_regs->pwm);
+}
+
+static int cht_wc_leds_probe(struct platform_device *pdev)
+{
+	struct intel_soc_pmic *pmic = dev_get_drvdata(pdev->dev.parent);
+	struct cht_wc_leds *leds;
+	int ret;
+	int i;
+
+	/*
+	 * On the Lenovo Yoga Tab 3 the LED1 driver output is actually
+	 * connected to a haptic feedback motor rather then a LED.
+	 * So do not register a LED classdev there (LED2 is unused).
+	 */
+	if (pmic->cht_wc_model == INTEL_CHT_WC_LENOVO_YT3_X90)
+		return -ENODEV;
+
+	leds = devm_kzalloc(&pdev->dev, sizeof(*leds), GFP_KERNEL);
+	if (!leds)
+		return -ENOMEM;
+
+	/*
+	 * LED1 might be in hw-controlled mode when this driver gets loaded; and
+	 * since the PMIC is always powered by the battery any changes made are
+	 * permanent. Save LED1 regs to restore them on remove() or shutdown().
+	 */
+	leds->leds[0].regs = &cht_wc_led_regs[0];
+	leds->leds[0].regmap = pmic->regmap;
+	ret = cht_wc_led_save_regs(&leds->leds[0], &leds->led1_initial_regs);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < CHT_WC_LED_COUNT; i++) {
+		struct cht_wc_led *led = &leds->leds[i];
+
+		led->regs = &cht_wc_led_regs[i];
+		led->regmap = pmic->regmap;
+		mutex_init(&led->mutex);
+		led->cdev.name = cht_wc_leds_names[i];
+		led->cdev.brightness_set_blocking = cht_wc_leds_brightness_set;
+		led->cdev.brightness_get = cht_wc_leds_brightness_get;
+		led->cdev.blink_set = cht_wc_leds_blink_set;
+		led->cdev.max_brightness = 255;
+
+		ret = led_classdev_register(&pdev->dev, &led->cdev);
+		if (ret < 0)
+			return ret;
+	}
+
+	platform_set_drvdata(pdev, leds);
+	return 0;
+}
+
+static void cht_wc_leds_remove(struct platform_device *pdev)
+{
+	struct cht_wc_leds *leds = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < CHT_WC_LED_COUNT; i++)
+		led_classdev_unregister(&leds->leds[i].cdev);
+
+	/* Restore LED1 regs if hw-control was active else leave LED1 off */
+	if (!(leds->led1_initial_regs.ctrl & CHT_WC_LED1_SWCTL))
+		cht_wc_led_restore_regs(&leds->leds[0], &leds->led1_initial_regs);
+}
+
+static void cht_wc_leds_disable(struct platform_device *pdev)
+{
+	struct cht_wc_leds *leds = platform_get_drvdata(pdev);
+	int i;
+
+	for (i = 0; i < CHT_WC_LED_COUNT; i++)
+		cht_wc_leds_brightness_set(&leds->leds[i].cdev, 0);
+
+	/* Restore LED1 regs if hw-control was active else leave LED1 off */
+	if (!(leds->led1_initial_regs.ctrl & CHT_WC_LED1_SWCTL))
+		cht_wc_led_restore_regs(&leds->leds[0], &leds->led1_initial_regs);
+}
+
+static struct platform_driver cht_wc_leds_driver = {
+	.probe = cht_wc_leds_probe,
+	.remove_new = cht_wc_leds_remove,
+	.shutdown = cht_wc_leds_disable,
+	.driver = {
+		.name = "cht_wcove_leds",
+	},
+};
+module_platform_driver(cht_wc_leds_driver);
+
+MODULE_ALIAS("platform:cht_wcove_leds");
+MODULE_DESCRIPTION("Intel Cherry Trail Whiskey Cove PMIC LEDs driver");
+MODULE_AUTHOR("Yauhen Kharuzhy <jekhor@gmail.com>");
+MODULE_LICENSE("GPL");
-- 
2.39.2

[PATCH v3 2/5] leds: cht-wcove: Add suspend/resume handling

[Hans de Goede]

When LED1 is showing the tablet is charging and then the device gets
suspended followed by unplugging the charger, then it will incorrectly
still show it is charging.

To avoid this turn both LEDs off on suspend, just like the PMIC always
turns them off when the tablet is powered off (even if the tablet is
charging). If hw-control is supported for LED1, then restore the
initial hw-control settings to let the hw control LED1 while suspended.

To restore the state the LEDs had before suspending, save it before
turning the LEDs off and restore it on resume.

Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/leds/leds-cht-wcove.c | 33 +++++++++++++++++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/drivers/leds/leds-cht-wcove.c b/drivers/leds/leds-cht-wcove.c
index 9fe76a0c62c8..166b140e132a 100644
--- a/drivers/leds/leds-cht-wcove.c
+++ b/drivers/leds/leds-cht-wcove.c
@@ -17,6 +17,7 @@
 #include <linux/mod_devicetable.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <linux/suspend.h>
 
 #define CHT_WC_LED1_CTRL		0x5e1f
 #define CHT_WC_LED1_FSM			0x5e20
@@ -69,6 +70,7 @@ struct cht_wc_led {
 	const struct cht_wc_led_regs *regs;
 	struct regmap *regmap;
 	struct mutex mutex;
+	struct cht_wc_led_saved_regs saved_regs;
 };
 
 struct cht_wc_leds {
@@ -364,12 +366,43 @@ static void cht_wc_leds_disable(struct platform_device *pdev)
 		cht_wc_led_restore_regs(&leds->leds[0], &leds->led1_initial_regs);
 }
 
+/* On suspend save current settings and turn LEDs off */
+static int cht_wc_leds_suspend(struct device *dev)
+{
+	struct cht_wc_leds *leds = dev_get_drvdata(dev);
+	int i, ret;
+
+	for (i = 0; i < CHT_WC_LED_COUNT; i++) {
+		ret = cht_wc_led_save_regs(&leds->leds[i], &leds->leds[i].saved_regs);
+		if (ret < 0)
+			return ret;
+	}
+
+	cht_wc_leds_disable(to_platform_device(dev));
+	return 0;
+}
+
+/* On resume restore the saved settings */
+static int cht_wc_leds_resume(struct device *dev)
+{
+	struct cht_wc_leds *leds = dev_get_drvdata(dev);
+	int i;
+
+	for (i = 0; i < CHT_WC_LED_COUNT; i++)
+		cht_wc_led_restore_regs(&leds->leds[i], &leds->leds[i].saved_regs);
+
+	return 0;
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(cht_wc_leds_pm, cht_wc_leds_suspend, cht_wc_leds_resume);
+
 static struct platform_driver cht_wc_leds_driver = {
 	.probe = cht_wc_leds_probe,
 	.remove_new = cht_wc_leds_remove,
 	.shutdown = cht_wc_leds_disable,
 	.driver = {
 		.name = "cht_wcove_leds",
+		.pm = pm_sleep_ptr(&cht_wc_leds_pm),
 	},
 };
 module_platform_driver(cht_wc_leds_driver);
-- 
2.39.2

[PATCH v3 3/5] leds: cht-wcove: Add support for breathing mode use hw_pattern sysfs API

[Hans de Goede]

The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
be used for a hw-breathing effect.

As discussed during review of v2 of the submission of the new
leds-cht-wcove driver, the LED subsystem already supports breathing mode
on several other LED controllers using the hw_pattern interface.

Implement a pattern_set callback to implement breathing mode modelled
after the breathing mode supported by the SC27xx breathing light and
Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
is closer to the EL15203000 one then to the SC27xx one since it does
not support staying high / low for a specific time, it only supports
rise and fall times.

As such the supported hw_pattern and the documentation for this is almost
a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.

Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v3
- s/LED_OFF/0/ and s/LED_ON/1/

Changes in v2
- Improve/extend Documentation/leds/leds-cht-wcove.rst a bit
---
 Documentation/leds/index.rst          |  1 +
 Documentation/leds/leds-cht-wcove.rst | 38 ++++++++++++++++++++++++
 drivers/leds/leds-cht-wcove.c         | 42 ++++++++++++++++++++++++---
 3 files changed, 77 insertions(+), 4 deletions(-)
 create mode 100644 Documentation/leds/leds-cht-wcove.rst

diff --git a/Documentation/leds/index.rst b/Documentation/leds/index.rst
index b9ca081fac71..c92612271e25 100644
--- a/Documentation/leds/index.rst
+++ b/Documentation/leds/index.rst
@@ -17,6 +17,7 @@ LEDs
    uleds
 
    leds-blinkm
+   leds-cht-wcove
    leds-el15203000
    leds-lm3556
    leds-lp3944
diff --git a/Documentation/leds/leds-cht-wcove.rst b/Documentation/leds/leds-cht-wcove.rst
new file mode 100644
index 000000000000..5ec7cb60c4aa
--- /dev/null
+++ b/Documentation/leds/leds-cht-wcove.rst
@@ -0,0 +1,38 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===========================================================
+Kernel driver for Intel Cherry Trail Whiskey Cove PMIC LEDs
+===========================================================
+
+/sys/class/leds/<led>/hw_pattern
+--------------------------------
+
+Specify a hardware pattern for the Whiskey Cove PMIC LEDs.
+
+The only supported pattern is hardware breathing mode::
+
+    "0 2000 1 2000"
+
+	^
+	|
+    Max-|     ---
+	|    /   \
+	|   /     \
+	|  /       \     /
+	| /         \   /
+    Min-|-           ---
+	|
+	0------2------4--> time (sec)
+
+The rise and fall times must be the same value.
+Supported values are 2000, 1000, 500 and 250 for
+breathing frequencies of 1/4, 1/2, 1 and 2 Hz.
+
+The set pattern only controls the timing. For max brightness the last
+set brightness is used and the max brightness can be changed
+while breathing by writing the brightness attribute.
+
+This is just like how blinking works in the LED subsystem,
+for both sw and hw blinking the brightness can also be changed
+while blinking. Breathing on this hw really is just a variant
+mode of blinking.
diff --git a/drivers/leds/leds-cht-wcove.c b/drivers/leds/leds-cht-wcove.c
index 166b140e132a..36fb4c2c3c13 100644
--- a/drivers/leds/leds-cht-wcove.c
+++ b/drivers/leds/leds-cht-wcove.c
@@ -217,9 +217,10 @@ static int cht_wc_leds_find_freq(unsigned long period)
 		return -1;
 }
 
-static int cht_wc_leds_blink_set(struct led_classdev *cdev,
-				 unsigned long *delay_on,
-				 unsigned long *delay_off)
+static int cht_wc_leds_set_effect(struct led_classdev *cdev,
+				  unsigned long *delay_on,
+				  unsigned long *delay_off,
+				  u8 effect)
 {
 	struct cht_wc_led *led = container_of(cdev, struct cht_wc_led, cdev);
 	unsigned int ctrl;
@@ -246,7 +247,7 @@ static int cht_wc_leds_blink_set(struct led_classdev *cdev,
 	}
 
 	ret = regmap_update_bits(led->regmap, led->regs->fsm,
-				 CHT_WC_LED_EFF_MASK, CHT_WC_LED_EFF_BLINKING);
+				 CHT_WC_LED_EFF_MASK, effect);
 	if (ret < 0)
 		dev_err(cdev->dev, "Failed to update LED FSM reg: %d\n", ret);
 
@@ -265,6 +266,37 @@ static int cht_wc_leds_blink_set(struct led_classdev *cdev,
 	return ret;
 }
 
+static int cht_wc_leds_blink_set(struct led_classdev *cdev,
+				 unsigned long *delay_on,
+				 unsigned long *delay_off)
+{
+	return cht_wc_leds_set_effect(cdev, delay_on, delay_off, CHT_WC_LED_EFF_BLINKING);
+}
+
+static int cht_wc_leds_pattern_set(struct led_classdev *cdev,
+				   struct led_pattern *pattern,
+				   u32 len, int repeat)
+{
+	unsigned long delay_off, delay_on;
+
+	if (repeat > 0 || len != 2 ||
+	    pattern[0].brightness != 0 || pattern[1].brightness != 1 ||
+	    pattern[0].delta_t != pattern[1].delta_t ||
+	    (pattern[0].delta_t != 250 && pattern[0].delta_t != 500 &&
+	     pattern[0].delta_t != 1000 && pattern[0].delta_t != 2000))
+		return -EINVAL;
+
+	delay_off = pattern[0].delta_t;
+	delay_on  = pattern[1].delta_t;
+
+	return cht_wc_leds_set_effect(cdev, &delay_on, &delay_off, CHT_WC_LED_EFF_BREATHING);
+}
+
+static int cht_wc_leds_pattern_clear(struct led_classdev *cdev)
+{
+	return cht_wc_leds_brightness_set(cdev, 0);
+}
+
 static int cht_wc_led_save_regs(struct cht_wc_led *led,
 				struct cht_wc_led_saved_regs *saved_regs)
 {
@@ -329,6 +361,8 @@ static int cht_wc_leds_probe(struct platform_device *pdev)
 		led->cdev.brightness_set_blocking = cht_wc_leds_brightness_set;
 		led->cdev.brightness_get = cht_wc_leds_brightness_get;
 		led->cdev.blink_set = cht_wc_leds_blink_set;
+		led->cdev.pattern_set = cht_wc_leds_pattern_set;
+		led->cdev.pattern_clear = cht_wc_leds_pattern_clear;
 		led->cdev.max_brightness = 255;
 
 		ret = led_classdev_register(&pdev->dev, &led->cdev);
-- 
2.39.2

[PATCH v3 4/5] leds: cht-wcove: Set default trigger for charging LED

[Hans de Goede]

Set a default trigger for the charging LED based on the machine-model
as set by the PMIC MFD driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/leds/leds-cht-wcove.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/leds/leds-cht-wcove.c b/drivers/leds/leds-cht-wcove.c
index 36fb4c2c3c13..ee9fb4bee018 100644
--- a/drivers/leds/leds-cht-wcove.c
+++ b/drivers/leds/leds-cht-wcove.c
@@ -351,6 +351,22 @@ static int cht_wc_leds_probe(struct platform_device *pdev)
 	if (ret < 0)
 		return ret;
 
+	/* Set LED1 default trigger based on machine model */
+	switch (pmic->cht_wc_model) {
+	case INTEL_CHT_WC_GPD_WIN_POCKET:
+		leds->leds[0].cdev.default_trigger = "max170xx_battery-charging-blink-full-solid";
+		break;
+	case INTEL_CHT_WC_XIAOMI_MIPAD2:
+		leds->leds[0].cdev.default_trigger = "bq27520-0-charging-blink-full-solid";
+		break;
+	case INTEL_CHT_WC_LENOVO_YOGABOOK1:
+		leds->leds[0].cdev.default_trigger = "bq27542-0-charging-blink-full-solid";
+		break;
+	default:
+		dev_warn(&pdev->dev, "Unknown model, no default charging trigger\n");
+		break;
+	}
+
 	for (i = 0; i < CHT_WC_LED_COUNT; i++) {
 		struct cht_wc_led *led = &leds->leds[i];
 
-- 
2.39.2

[PATCH v3 5/5] leds: cht-wcove: Use breathing when LED_INIT_DEFAULT_TRIGGER is set

[Hans de Goede]

The desired default behavior of LED1 / the charge LED is breathing
while charging and on/solid when full. Since triggers cannot select
breathing, blink_set() gets called when charging. Use breathing
when the default "charging-blink-full-solid" trigger is used to
achieve the desired default behavior.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v3:
- Also set on/off delay to 1000 so that we get a slow breathing effect,
  this counter-acts the v2 cht_wc_leds_set_effect() change changing
  the default delays from 1000 to 500
---
 drivers/leds/leds-cht-wcove.c | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/drivers/leds/leds-cht-wcove.c b/drivers/leds/leds-cht-wcove.c
index ee9fb4bee018..0cfebee98910 100644
--- a/drivers/leds/leds-cht-wcove.c
+++ b/drivers/leds/leds-cht-wcove.c
@@ -270,7 +270,21 @@ static int cht_wc_leds_blink_set(struct led_classdev *cdev,
 				 unsigned long *delay_on,
 				 unsigned long *delay_off)
 {
-	return cht_wc_leds_set_effect(cdev, delay_on, delay_off, CHT_WC_LED_EFF_BLINKING);
+	u8 effect = CHT_WC_LED_EFF_BLINKING;
+
+	/*
+	 * The desired default behavior of LED1 / the charge LED is breathing
+	 * while charging and on/solid when full. Since triggers cannot select
+	 * breathing, blink_set() gets called when charging. Use slow breathing
+	 * when the default "charging-blink-full-solid" trigger is used to
+	 * achieve the desired default behavior.
+	 */
+	if (cdev->flags & LED_INIT_DEFAULT_TRIGGER) {
+		*delay_on = *delay_off = 1000;
+		effect = CHT_WC_LED_EFF_BREATHING;
+	}
+
+	return cht_wc_leds_set_effect(cdev, delay_on, delay_off, effect);
 }
 
 static int cht_wc_leds_pattern_set(struct led_classdev *cdev,
-- 
2.39.2

Re: [PATCH v3 0/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Yauhen Kharuzhy]

On Sun, Apr 30, 2023 at 09:59:47PM +0200, Hans de Goede wrote:
> Hi All,
> 
> Here is v3 of the patch series to add support for the LED controller
> on Intel Cherry Trail Whiskey Cove PMICs.
> 
> Changes in v3:
> - Some comment tweaks and s/LED_OFF/0/ and s/LED_ON/1/
> - Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
>   is connected to a haptic feedback motor there (and LED2 is unused)
> 
> Changes in v2 (of my version of this):
> - Address Pavel's small remarks on patch 1/5,
>   see patch 1/5's commit message for details
> - Improve/extend pattern docs in Documentation/leds/leds-cht-wcove.rst
> 
> This is based on the original patch for this from Yauhen Kharuzhy,
> with additional work on top by me.
> 
> This addresses the review remarks on the v2 posting from Yauhen:
> - Since the PMIC is connected to the battery any changes we make to
>   the LED settings are permanent, even surviving reboot / poweroff.
>   Save LED1 register settings on probe() and if auto-/hw-control was
>   enabled on probe() restore the settings on remove() and shutdown().
> - Add support for the pattern trigger to select breathing mode
> 
> This makes the charging LED on devices with these PMICs properly
> reflect the charging status (this relies on sw control on most
> devices) and this also allows control of the LED behind the pen
> (digitizer on) symbol on the keyboard half of the Lenovo Yoga Book
> 1 models.
> 
> Regards,
> 
> Hans

Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>

Works at my Lenovo Yoga Book YB1-X91L.

-- 
Yauhen Kharuzhy

Re: [PATCH v3 0/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Hans de Goede]

Hi Yauhen,

On 5/4/23 10:05, Yauhen Kharuzhy wrote:
> On Sun, Apr 30, 2023 at 09:59:47PM +0200, Hans de Goede wrote:
>> Hi All,
>>
>> Here is v3 of the patch series to add support for the LED controller
>> on Intel Cherry Trail Whiskey Cove PMICs.
>>
>> Changes in v3:
>> - Some comment tweaks and s/LED_OFF/0/ and s/LED_ON/1/
>> - Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
>>   is connected to a haptic feedback motor there (and LED2 is unused)
>>
>> Changes in v2 (of my version of this):
>> - Address Pavel's small remarks on patch 1/5,
>>   see patch 1/5's commit message for details
>> - Improve/extend pattern docs in Documentation/leds/leds-cht-wcove.rst
>>
>> This is based on the original patch for this from Yauhen Kharuzhy,
>> with additional work on top by me.
>>
>> This addresses the review remarks on the v2 posting from Yauhen:
>> - Since the PMIC is connected to the battery any changes we make to
>>   the LED settings are permanent, even surviving reboot / poweroff.
>>   Save LED1 register settings on probe() and if auto-/hw-control was
>>   enabled on probe() restore the settings on remove() and shutdown().
>> - Add support for the pattern trigger to select breathing mode
>>
>> This makes the charging LED on devices with these PMICs properly
>> reflect the charging status (this relies on sw control on most
>> devices) and this also allows control of the LED behind the pen
>> (digitizer on) symbol on the keyboard half of the Lenovo Yoga Book
>> 1 models.
>>
>> Regards,
>>
>> Hans
> 
> Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
> 
> Works at my Lenovo Yoga Book YB1-X91L.

Thank you!

I assume you have tested with my LED class/core series which avoids
the oops/WARN() you were seeing before:

https://lore.kernel.org/linux-leds/20230412215855.593541-1-hdegoede@redhat.com/

If yes, can you reply with your Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
to that series too please ?

Regards,

Hans


p.s.

I think on an earlier version of this series you mentioned that you
are still carrying some patches locally for the yogabook ?

If I remember that correctly can you share those patches with me/us ?

Then if I can find some time I can see if I can submit them upstream
(or find another way to achieve their goal and post that upstream).

Also while on the subject of the yogabook have you looked into
getting sound to work ?

Re: [PATCH v3 0/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Yauhen Kharuzhy]

чт, 4 мая 2023 г. в 11:56, Hans de Goede <hdegoede@redhat.com>:
>
> Hi Yauhen,
>
> On 5/4/23 10:05, Yauhen Kharuzhy wrote:
> > On Sun, Apr 30, 2023 at 09:59:47PM +0200, Hans de Goede wrote:
> >> Hi All,
> >>
> >> Here is v3 of the patch series to add support for the LED controller
> >> on Intel Cherry Trail Whiskey Cove PMICs.
> >>
> >> Changes in v3:
> >> - Some comment tweaks and s/LED_OFF/0/ and s/LED_ON/1/
> >> - Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
> >>   is connected to a haptic feedback motor there (and LED2 is unused)
> >>
> >> Changes in v2 (of my version of this):
> >> - Address Pavel's small remarks on patch 1/5,
> >>   see patch 1/5's commit message for details
> >> - Improve/extend pattern docs in Documentation/leds/leds-cht-wcove.rst
> >>
> >> This is based on the original patch for this from Yauhen Kharuzhy,
> >> with additional work on top by me.
> >>
> >> This addresses the review remarks on the v2 posting from Yauhen:
> >> - Since the PMIC is connected to the battery any changes we make to
> >>   the LED settings are permanent, even surviving reboot / poweroff.
> >>   Save LED1 register settings on probe() and if auto-/hw-control was
> >>   enabled on probe() restore the settings on remove() and shutdown().
> >> - Add support for the pattern trigger to select breathing mode
> >>
> >> This makes the charging LED on devices with these PMICs properly
> >> reflect the charging status (this relies on sw control on most
> >> devices) and this also allows control of the LED behind the pen
> >> (digitizer on) symbol on the keyboard half of the Lenovo Yoga Book
> >> 1 models.
> >>
> >> Regards,
> >>
> >> Hans
> >
> > Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
> >
> > Works at my Lenovo Yoga Book YB1-X91L.
>
> Thank you!
>
> I assume you have tested with my LED class/core series which avoids
> the oops/WARN() you were seeing before:
>
> https://lore.kernel.org/linux-leds/20230412215855.593541-1-hdegoede@redhat.com/
>
> If yes, can you reply with your Tested-by: Yauhen Kharuzhy <jekhor@gmail.com>
> to that series too please ?

Yes, sure, I will reply there too.

> Regards,
>
> Hans
>
>
> p.s.
>
> I think on an earlier version of this series you mentioned that you
> are still carrying some patches locally for the yogabook ?
>
> If I remember that correctly can you share those patches with me/us ?

Of course, all my patches are in my github:
https://github.com/jekhor/yogabook-linux-kernel/commits/master

>
> Then if I can find some time I can see if I can submit them upstream
> (or find another way to achieve their goal and post that upstream).
>
> Also while on the subject of the yogabook have you looked into
> getting sound to work ?

Sound works for me with my kernel, speakers and DMIC. UCM configs are
needed to get it working:
https://github.com/jekhor/alsa-ucm-conf-yogabook/tree/main


-- 
Yauhen Kharuzhy

Re: [PATCH v3 1/5] leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver

[Lee Jones]

On Sun, 30 Apr 2023, Hans de Goede wrote:

> From: Yauhen Kharuzhy <jekhor@gmail.com>
> 
> Add support for LEDs connected to the Intel Cherry Trail Whiskey Cove
> PMIC. Charger and general-purpose LEDs are supported. Hardware blinking
> is implemented, breathing is not.
> 
> This driver was tested with Lenovo Yoga Book notebook.
> 
> Changes by Hans de Goede (in response to review of v2):
> - Since the PMIC is connected to the battery any changes we make to
>   the LED settings are permanent, even surviving reboot / poweroff.
>   Save LED1 register settings on probe() and if auto-/hw-control was
>   enabled on probe() restore the settings on remove() and shutdown().
> - Delay switching LED1 to software control mode to first brightness write.
> - Use dynamically allocated drvdata instead of a global drvdata variable.
> - Ensure the LED is on when activating blinking.
> - Fix CHT_WC_LED_EFF_BREATHING val ((3 << 1) rather then BIT(3)).
> 
> Link: https://lore.kernel.org/r/20190212205901.13037-2-jekhor@gmail.com
> Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
> Co-developed-by: Hans de Goede <hdegoede@redhat.com>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v3:
> - Some comment tweaks and s/LED_OFF/0/
> - Refuse to load on the Yoga Tab 3 as it turns out the LED1 driver output
>   is connected to a haptic feedback motor there (and LED2 is unused)
> 
> Changes in v2:
> - Update comment about YB1 kernel source usage for register info
> - Replace "cht-wc::" LED name prefix with "platform::"
> - Add leds-cht-wcove to list of drivers using "platform::charging" in
>   Documentation/leds/well-known-leds.txt
> - Bail from cht_wc_leds_brightness_set() on first error
> - Make default blink 1Hz, like sw-blink default blink
> ---
>  Documentation/leds/well-known-leds.txt |   2 +-
>  drivers/leds/Kconfig                   |  11 +
>  drivers/leds/Makefile                  |   1 +
>  drivers/leds/leds-cht-wcove.c          | 380 +++++++++++++++++++++++++
>  4 files changed, 393 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/leds/leds-cht-wcove.c

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v3 2/5] leds: cht-wcove: Add suspend/resume handling

[Lee Jones]

On Sun, 30 Apr 2023, Hans de Goede wrote:

> When LED1 is showing the tablet is charging and then the device gets
> suspended followed by unplugging the charger, then it will incorrectly
> still show it is charging.
> 
> To avoid this turn both LEDs off on suspend, just like the PMIC always
> turns them off when the tablet is powered off (even if the tablet is
> charging). If hw-control is supported for LED1, then restore the
> initial hw-control settings to let the hw control LED1 while suspended.
> 
> To restore the state the LEDs had before suspending, save it before
> turning the LEDs off and restore it on resume.
> 
> Acked-by: Pavel Machek <pavel@ucw.cz>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  drivers/leds/leds-cht-wcove.c | 33 +++++++++++++++++++++++++++++++++
>  1 file changed, 33 insertions(+)

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v3 3/5] leds: cht-wcove: Add support for breathing mode use hw_pattern sysfs API

[Lee Jones]

On Sun, 30 Apr 2023, Hans de Goede wrote:

> The hw-blinking of the LED controller in the Whiskey Cove PMIC can also
> be used for a hw-breathing effect.
> 
> As discussed during review of v2 of the submission of the new
> leds-cht-wcove driver, the LED subsystem already supports breathing mode
> on several other LED controllers using the hw_pattern interface.
> 
> Implement a pattern_set callback to implement breathing mode modelled
> after the breathing mode supported by the SC27xx breathing light and
> Crane EL15203000 LED drivers. The Whiskey Cove PMIC's breathing mode
> is closer to the EL15203000 one then to the SC27xx one since it does
> not support staying high / low for a specific time, it only supports
> rise and fall times.
> 
> As such the supported hw_pattern and the documentation for this is almost
> a 1:1 copy of the pattern/docs for the EL15203000 breathing mode.
> 
> Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
> Link: https://lore.kernel.org/all/6beed61c-1fc6-6525-e873-a8978f5fbffb@gmail.com/
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v3
> - s/LED_OFF/0/ and s/LED_ON/1/
> 
> Changes in v2
> - Improve/extend Documentation/leds/leds-cht-wcove.rst a bit
> ---
>  Documentation/leds/index.rst          |  1 +
>  Documentation/leds/leds-cht-wcove.rst | 38 ++++++++++++++++++++++++
>  drivers/leds/leds-cht-wcove.c         | 42 ++++++++++++++++++++++++---
>  3 files changed, 77 insertions(+), 4 deletions(-)
>  create mode 100644 Documentation/leds/leds-cht-wcove.rst

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v3 4/5] leds: cht-wcove: Set default trigger for charging LED

[Lee Jones]

On Sun, 30 Apr 2023, Hans de Goede wrote:

> Set a default trigger for the charging LED based on the machine-model
> as set by the PMIC MFD driver.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  drivers/leds/leds-cht-wcove.c | 16 ++++++++++++++++
>  1 file changed, 16 insertions(+)

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v3 5/5] leds: cht-wcove: Use breathing when LED_INIT_DEFAULT_TRIGGER is set

[Lee Jones]

On Sun, 30 Apr 2023, Hans de Goede wrote:

> The desired default behavior of LED1 / the charge LED is breathing
> while charging and on/solid when full. Since triggers cannot select
> breathing, blink_set() gets called when charging. Use breathing
> when the default "charging-blink-full-solid" trigger is used to
> achieve the desired default behavior.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
> Changes in v3:
> - Also set on/off delay to 1000 so that we get a slow breathing effect,
>   this counter-acts the v2 cht_wc_leds_set_effect() change changing
>   the default delays from 1000 to 500
> ---
>  drivers/leds/leds-cht-wcove.c | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)

Applied, thanks

-- 
Lee Jones [李琼斯]