From: Dongchun Zhu <dongchun.zhu@mediatek.com>
To: <mchehab@kernel.org>, <andriy.shevchenko@linux.intel.com>,
<robh+dt@kernel.org>, <mark.rutland@arm.com>,
<sakari.ailus@linux.intel.com>, <drinkcat@chromium.org>,
<tfiga@chromium.org>, <matthias.bgg@gmail.com>,
<bingbu.cao@intel.com>
Cc: <srv_heupstream@mediatek.com>,
<linux-mediatek@lists.infradead.org>,
<linux-arm-kernel@lists.infradead.org>, <sj.huang@mediatek.com>,
<linux-media@vger.kernel.org>, <devicetree@vger.kernel.org>,
<louis.kuo@mediatek.com>, <shengnan.wang@mediatek.com>,
<dongchun.zhu@mediatek.com>
Subject: [V3, 2/2] media: i2c: ov8856: Add support for more sensor modes
Date: Thu, 31 Oct 2019 17:02:13 +0800 [thread overview]
Message-ID: <20191031090213.27727-3-dongchun.zhu@mediatek.com> (raw)
In-Reply-To: <20191031090213.27727-1-dongchun.zhu@mediatek.com>
This adds two more sensor modes for Omnivision ov8856 image sensor,
including the resolution of 1632*1224 and 3264*2448, both with the
Bayer Order of BGGR.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
---
drivers/media/i2c/ov8856.c | 661 ++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 652 insertions(+), 9 deletions(-)
diff --git a/drivers/media/i2c/ov8856.c b/drivers/media/i2c/ov8856.c
index 8655842..4815c26 100644
--- a/drivers/media/i2c/ov8856.c
+++ b/drivers/media/i2c/ov8856.c
@@ -3,10 +3,13 @@
#include <asm/unaligned.h>
#include <linux/acpi.h>
+#include <linux/clk.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
#include <media/v4l2-ctrls.h>
#include <media/v4l2-device.h>
#include <media/v4l2-fwnode.h>
@@ -18,10 +21,15 @@
#define OV8856_LINK_FREQ_360MHZ 360000000ULL
#define OV8856_LINK_FREQ_180MHZ 180000000ULL
#define OV8856_SCLK 144000000ULL
-#define OV8856_MCLK 19200000
+#define OV8856_XVCLK_19_2 19200000
+#define OV8856_XVCLK_24 24000000
#define OV8856_DATA_LANES 4
#define OV8856_RGB_DEPTH 10
+#define REG_X_ADDR_START 0x3808
+#define X_OUTPUT_FULL_SIZE 0x0cc0
+#define X_OUTPUT_BINNING_SIZE 0x0660
+
#define OV8856_REG_CHIP_ID 0x300a
#define OV8856_CHIP_ID 0x00885a
@@ -29,6 +37,22 @@
#define OV8856_MODE_STANDBY 0x00
#define OV8856_MODE_STREAMING 0x01
+/* define 1B module revision */
+#define OV8856_1B_MODULE 0x02
+
+/* the OTP read-out buffer is at 0x7000 and 0xf is the offset
+ * of the byte in the OTP that means the module revision
+ */
+#define OV8856_MODULE_REVISION 0x700f
+#define OV8856_OTP_MODE_CTRL 0x3d84
+#define OV8856_OTP_LOAD_CTRL 0x3d81
+#define OV8856_OTP_MODE_AUTO 0x00
+#define OV8856_OTP_LOAD_CTRL_ENABLE BIT(0)
+
+/* Analog control register that decided by module revision */
+#define OV8856_ANAL_MODE_CTRL 0x3614
+#define OV8856_ANAL_1B_VAL 0x20
+
/* vertical-timings from sensor */
#define OV8856_REG_VTS 0x380e
#define OV8856_VTS_MAX 0x7fff
@@ -64,6 +88,14 @@
#define to_ov8856(_sd) container_of(_sd, struct ov8856, sd)
+static const char * const ov8856_supply_names[] = {
+ "dovdd", /* Digital I/O power */
+ "avdd", /* Analog power */
+ "dvdd", /* Digital core power */
+};
+
+#define OV8856_NUM_SUPPLIES ARRAY_SIZE(ov8856_supply_names)
+
enum {
OV8856_LINK_FREQ_720MBPS,
OV8856_LINK_FREQ_360MBPS,
@@ -316,6 +348,209 @@ static const struct ov8856_reg mode_3280x2464_regs[] = {
{0x5e00, 0x00}
};
+static const struct ov8856_reg mode_3264x2448_regs[] = {
+ {0x0103, 0x01},
+ {0x0302, 0x3c},
+ {0x0303, 0x01},
+ {0x031e, 0x0c},
+ {0x3000, 0x20},
+ {0x3003, 0x08},
+ {0x300e, 0x20},
+ {0x3010, 0x00},
+ {0x3015, 0x84},
+ {0x3018, 0x72},
+ {0x3021, 0x23},
+ {0x3033, 0x24},
+ {0x3500, 0x00},
+ {0x3501, 0x9a},
+ {0x3502, 0x20},
+ {0x3503, 0x08},
+ {0x3505, 0x83},
+ {0x3508, 0x01},
+ {0x3509, 0x80},
+ {0x350c, 0x00},
+ {0x350d, 0x80},
+ {0x350e, 0x04},
+ {0x350f, 0x00},
+ {0x3510, 0x00},
+ {0x3511, 0x02},
+ {0x3512, 0x00},
+ {0x3600, 0x72},
+ {0x3601, 0x40},
+ {0x3602, 0x30},
+ {0x3610, 0xc5},
+ {0x3611, 0x58},
+ {0x3612, 0x5c},
+ {0x3613, 0xca},
+ {0x3614, 0x60},
+ {0x3628, 0xff},
+ {0x3629, 0xff},
+ {0x362a, 0xff},
+ {0x3633, 0x10},
+ {0x3634, 0x10},
+ {0x3635, 0x10},
+ {0x3636, 0x10},
+ {0x3663, 0x08},
+ {0x3669, 0x34},
+ {0x366d, 0x00},
+ {0x366e, 0x10},
+ {0x3706, 0x86},
+ {0x370b, 0x7e},
+ {0x3714, 0x23},
+ {0x3730, 0x12},
+ {0x3733, 0x10},
+ {0x3764, 0x00},
+ {0x3765, 0x00},
+ {0x3769, 0x62},
+ {0x376a, 0x2a},
+ {0x376b, 0x30},
+ {0x3780, 0x00},
+ {0x3781, 0x24},
+ {0x3782, 0x00},
+ {0x3783, 0x23},
+ {0x3798, 0x2f},
+ {0x37a1, 0x60},
+ {0x37a8, 0x6a},
+ {0x37ab, 0x3f},
+ {0x37c2, 0x04},
+ {0x37c3, 0xf1},
+ {0x37c9, 0x80},
+ {0x37cb, 0x16},
+ {0x37cc, 0x16},
+ {0x37cd, 0x16},
+ {0x37ce, 0x16},
+ {0x3800, 0x00},
+ {0x3801, 0x00},
+ {0x3802, 0x00},
+ {0x3803, 0x0c},
+ {0x3804, 0x0c},
+ {0x3805, 0xdf},
+ {0x3806, 0x09},
+ {0x3807, 0xa3},
+ {0x3808, 0x0c},
+ {0x3809, 0xc0},
+ {0x380a, 0x09},
+ {0x380b, 0x90},
+ {0x380c, 0x07},
+ {0x380d, 0x8c},
+ {0x380e, 0x09},
+ {0x380f, 0xb2},
+ {0x3810, 0x00},
+ {0x3811, 0x04},
+ {0x3812, 0x00},
+ {0x3813, 0x02},
+ {0x3814, 0x01},
+ {0x3815, 0x01},
+ {0x3816, 0x00},
+ {0x3817, 0x00},
+ {0x3818, 0x00},
+ {0x3819, 0x10},
+ {0x3820, 0x80},
+ {0x3821, 0x46},
+ {0x382a, 0x01},
+ {0x382b, 0x01},
+ {0x3830, 0x06},
+ {0x3836, 0x02},
+ {0x3862, 0x04},
+ {0x3863, 0x08},
+ {0x3cc0, 0x33},
+ {0x3d85, 0x17},
+ {0x3d8c, 0x73},
+ {0x3d8d, 0xde},
+ {0x4001, 0xe0},
+ {0x4003, 0x40},
+ {0x4008, 0x00},
+ {0x4009, 0x0b},
+ {0x400a, 0x00},
+ {0x400b, 0x84},
+ {0x400f, 0x80},
+ {0x4010, 0xf0},
+ {0x4011, 0xff},
+ {0x4012, 0x02},
+ {0x4013, 0x01},
+ {0x4014, 0x01},
+ {0x4015, 0x01},
+ {0x4042, 0x00},
+ {0x4043, 0x80},
+ {0x4044, 0x00},
+ {0x4045, 0x80},
+ {0x4046, 0x00},
+ {0x4047, 0x80},
+ {0x4048, 0x00},
+ {0x4049, 0x80},
+ {0x4041, 0x03},
+ {0x404c, 0x20},
+ {0x404d, 0x00},
+ {0x404e, 0x20},
+ {0x4203, 0x80},
+ {0x4307, 0x30},
+ {0x4317, 0x00},
+ {0x4502, 0x50},
+ {0x4503, 0x08},
+ {0x4601, 0x80},
+ {0x4800, 0x44},
+ {0x4816, 0x53},
+ {0x481b, 0x50},
+ {0x481f, 0x27},
+ {0x4823, 0x3c},
+ {0x482b, 0x00},
+ {0x4831, 0x66},
+ {0x4837, 0x16},
+ {0x483c, 0x0f},
+ {0x484b, 0x05},
+ {0x5000, 0x77},
+ {0x5001, 0x0a},
+ {0x5003, 0xc8},
+ {0x5004, 0x04},
+ {0x5006, 0x00},
+ {0x5007, 0x00},
+ {0x502e, 0x03},
+ {0x5030, 0x41},
+ {0x5780, 0x14},
+ {0x5781, 0x0f},
+ {0x5782, 0x44},
+ {0x5783, 0x02},
+ {0x5784, 0x01},
+ {0x5785, 0x01},
+ {0x5786, 0x00},
+ {0x5787, 0x04},
+ {0x5788, 0x02},
+ {0x5789, 0x0f},
+ {0x578a, 0xfd},
+ {0x578b, 0xf5},
+ {0x578c, 0xf5},
+ {0x578d, 0x03},
+ {0x578e, 0x08},
+ {0x578f, 0x0c},
+ {0x5790, 0x08},
+ {0x5791, 0x04},
+ {0x5792, 0x00},
+ {0x5793, 0x52},
+ {0x5794, 0xa3},
+ {0x5795, 0x02},
+ {0x5796, 0x20},
+ {0x5797, 0x20},
+ {0x5798, 0xd5},
+ {0x5799, 0xd5},
+ {0x579a, 0x00},
+ {0x579b, 0x50},
+ {0x579c, 0x00},
+ {0x579d, 0x2c},
+ {0x579e, 0x0c},
+ {0x579f, 0x40},
+ {0x57a0, 0x09},
+ {0x57a1, 0x40},
+ {0x59f8, 0x3d},
+ {0x5a08, 0x02},
+ {0x5b00, 0x02},
+ {0x5b01, 0x10},
+ {0x5b02, 0x03},
+ {0x5b03, 0xcf},
+ {0x5b05, 0x6c},
+ {0x5e00, 0x00},
+ {0x5e10, 0xfc}
+};
+
static const struct ov8856_reg mode_1640x1232_regs[] = {
{0x3000, 0x20},
{0x3003, 0x08},
@@ -506,6 +741,209 @@ static const struct ov8856_reg mode_1640x1232_regs[] = {
{0x5e00, 0x00}
};
+static const struct ov8856_reg mode_1632x1224_regs[] = {
+ {0x0103, 0x01},
+ {0x0302, 0x3c},
+ {0x0303, 0x01},
+ {0x031e, 0x0c},
+ {0x3000, 0x20},
+ {0x3003, 0x08},
+ {0x300e, 0x20},
+ {0x3010, 0x00},
+ {0x3015, 0x84},
+ {0x3018, 0x72},
+ {0x3021, 0x23},
+ {0x3033, 0x24},
+ {0x3500, 0x00},
+ {0x3501, 0x4c},
+ {0x3502, 0xe0},
+ {0x3503, 0x08},
+ {0x3505, 0x83},
+ {0x3508, 0x01},
+ {0x3509, 0x80},
+ {0x350c, 0x00},
+ {0x350d, 0x80},
+ {0x350e, 0x04},
+ {0x350f, 0x00},
+ {0x3510, 0x00},
+ {0x3511, 0x02},
+ {0x3512, 0x00},
+ {0x3600, 0x72},
+ {0x3601, 0x40},
+ {0x3602, 0x30},
+ {0x3610, 0xc5},
+ {0x3611, 0x58},
+ {0x3612, 0x5c},
+ {0x3613, 0xca},
+ {0x3614, 0x60},
+ {0x3628, 0xff},
+ {0x3629, 0xff},
+ {0x362a, 0xff},
+ {0x3633, 0x10},
+ {0x3634, 0x10},
+ {0x3635, 0x10},
+ {0x3636, 0x10},
+ {0x3663, 0x08},
+ {0x3669, 0x34},
+ {0x366d, 0x00},
+ {0x366e, 0x08},
+ {0x3706, 0x86},
+ {0x370b, 0x7e},
+ {0x3714, 0x27},
+ {0x3730, 0x12},
+ {0x3733, 0x10},
+ {0x3764, 0x00},
+ {0x3765, 0x00},
+ {0x3769, 0x62},
+ {0x376a, 0x2a},
+ {0x376b, 0x30},
+ {0x3780, 0x00},
+ {0x3781, 0x24},
+ {0x3782, 0x00},
+ {0x3783, 0x23},
+ {0x3798, 0x2f},
+ {0x37a1, 0x60},
+ {0x37a8, 0x6a},
+ {0x37ab, 0x3f},
+ {0x37c2, 0x14},
+ {0x37c3, 0xf1},
+ {0x37c9, 0x80},
+ {0x37cb, 0x16},
+ {0x37cc, 0x16},
+ {0x37cd, 0x16},
+ {0x37ce, 0x16},
+ {0x3800, 0x00},
+ {0x3801, 0x00},
+ {0x3802, 0x00},
+ {0x3803, 0x0c},
+ {0x3804, 0x0c},
+ {0x3805, 0xdf},
+ {0x3806, 0x09},
+ {0x3807, 0xa3},
+ {0x3808, 0x06},
+ {0x3809, 0x60},
+ {0x380a, 0x04},
+ {0x380b, 0xc8},
+ {0x380c, 0x07},
+ {0x380d, 0x8c},
+ {0x380e, 0x09},
+ {0x380f, 0xb2},
+ {0x3810, 0x00},
+ {0x3811, 0x02},
+ {0x3812, 0x00},
+ {0x3813, 0x02},
+ {0x3814, 0x03},
+ {0x3815, 0x01},
+ {0x3816, 0x00},
+ {0x3817, 0x00},
+ {0x3818, 0x00},
+ {0x3819, 0x10},
+ {0x3820, 0x80},
+ {0x3821, 0x47},
+ {0x382a, 0x03},
+ {0x382b, 0x01},
+ {0x3830, 0x06},
+ {0x3836, 0x02},
+ {0x3862, 0x04},
+ {0x3863, 0x08},
+ {0x3cc0, 0x33},
+ {0x3d85, 0x17},
+ {0x3d8c, 0x73},
+ {0x3d8d, 0xde},
+ {0x4001, 0xe0},
+ {0x4003, 0x40},
+ {0x4008, 0x00},
+ {0x4009, 0x05},
+ {0x400a, 0x00},
+ {0x400b, 0x84},
+ {0x400f, 0x80},
+ {0x4010, 0xf0},
+ {0x4011, 0xff},
+ {0x4012, 0x02},
+ {0x4013, 0x01},
+ {0x4014, 0x01},
+ {0x4015, 0x01},
+ {0x4042, 0x00},
+ {0x4043, 0x80},
+ {0x4044, 0x00},
+ {0x4045, 0x80},
+ {0x4046, 0x00},
+ {0x4047, 0x80},
+ {0x4048, 0x00},
+ {0x4049, 0x80},
+ {0x4041, 0x03},
+ {0x404c, 0x20},
+ {0x404d, 0x00},
+ {0x404e, 0x20},
+ {0x4203, 0x80},
+ {0x4307, 0x30},
+ {0x4317, 0x00},
+ {0x4502, 0x50},
+ {0x4503, 0x08},
+ {0x4601, 0x80},
+ {0x4800, 0x44},
+ {0x4816, 0x53},
+ {0x481b, 0x50},
+ {0x481f, 0x27},
+ {0x4823, 0x3c},
+ {0x482b, 0x00},
+ {0x4831, 0x66},
+ {0x4837, 0x16},
+ {0x483c, 0x0f},
+ {0x484b, 0x05},
+ {0x5000, 0x77},
+ {0x5001, 0x0a},
+ {0x5003, 0xc8},
+ {0x5004, 0x04},
+ {0x5006, 0x00},
+ {0x5007, 0x00},
+ {0x502e, 0x03},
+ {0x5030, 0x41},
+ {0x5795, 0x00},
+ {0x5796, 0x10},
+ {0x5797, 0x10},
+ {0x5798, 0x73},
+ {0x5799, 0x73},
+ {0x579a, 0x00},
+ {0x579b, 0x28},
+ {0x579c, 0x00},
+ {0x579d, 0x16},
+ {0x579e, 0x06},
+ {0x579f, 0x20},
+ {0x57a0, 0x04},
+ {0x57a1, 0xa0},
+ {0x5780, 0x14},
+ {0x5781, 0x0f},
+ {0x5782, 0x44},
+ {0x5783, 0x02},
+ {0x5784, 0x01},
+ {0x5785, 0x01},
+ {0x5786, 0x00},
+ {0x5787, 0x04},
+ {0x5788, 0x02},
+ {0x5789, 0x0f},
+ {0x578a, 0xfd},
+ {0x578b, 0xf5},
+ {0x578c, 0xf5},
+ {0x578d, 0x03},
+ {0x578e, 0x08},
+ {0x578f, 0x0c},
+ {0x5790, 0x08},
+ {0x5791, 0x04},
+ {0x5792, 0x00},
+ {0x5793, 0x52},
+ {0x5794, 0xa3},
+ {0x59f8, 0x3d},
+ {0x5a08, 0x02},
+ {0x5b00, 0x02},
+ {0x5b01, 0x10},
+ {0x5b02, 0x03},
+ {0x5b03, 0xcf},
+ {0x5b05, 0x6c},
+ {0x5e00, 0x00},
+ {0x5e10, 0xfc}
+};
+
static const char * const ov8856_test_pattern_menu[] = {
"Disabled",
"Standard Color Bar",
@@ -548,6 +986,18 @@ static const struct ov8856_mode supported_modes[] = {
.link_freq_index = OV8856_LINK_FREQ_720MBPS,
},
{
+ .width = 3264,
+ .height = 2448,
+ .hts = 1932,
+ .vts_def = 2482,
+ .vts_min = 2482,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(mode_3264x2448_regs),
+ .regs = mode_3264x2448_regs,
+ },
+ .link_freq_index = OV8856_LINK_FREQ_720MBPS,
+ },
+ {
.width = 1640,
.height = 1232,
.hts = 3820,
@@ -558,6 +1008,18 @@ static const struct ov8856_mode supported_modes[] = {
.regs = mode_1640x1232_regs,
},
.link_freq_index = OV8856_LINK_FREQ_360MBPS,
+ },
+ {
+ .width = 1632,
+ .height = 1224,
+ .hts = 1932,
+ .vts_def = 2482,
+ .vts_min = 2482,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(mode_1632x1224_regs),
+ .regs = mode_1632x1224_regs,
+ },
+ .link_freq_index = OV8856_LINK_FREQ_360MBPS,
}
};
@@ -566,16 +1028,28 @@ struct ov8856 {
struct media_pad pad;
struct v4l2_ctrl_handler ctrl_handler;
+ struct clk *xvclk;
+ struct gpio_desc *n_shutdn_gpio;
+ struct regulator_bulk_data supplies[OV8856_NUM_SUPPLIES];
+
/* V4L2 Controls */
struct v4l2_ctrl *link_freq;
struct v4l2_ctrl *pixel_rate;
struct v4l2_ctrl *vblank;
struct v4l2_ctrl *hblank;
struct v4l2_ctrl *exposure;
+ struct v4l2_mbus_framefmt fmt;
/* Current mode */
const struct ov8856_mode *cur_mode;
+ /* module hardware version that can be read out from register 0x700f
+ * the register value corresponds to different hardware version
+ * 01: 2A module revision
+ * 02: 1B module revision
+ */
+ bool is_1B_revision;
+
/* To serialize asynchronus callbacks */
struct mutex mutex;
@@ -696,6 +1170,25 @@ static int ov8856_test_pattern(struct ov8856 *ov8856, u32 pattern)
OV8856_REG_VALUE_08BIT, pattern);
}
+static int ov8856_check_revision(struct ov8856 *ov8856)
+{
+ int ret;
+
+ ret = ov8856_write_reg(ov8856, OV8856_REG_MODE_SELECT,
+ OV8856_REG_VALUE_08BIT, OV8856_MODE_STREAMING);
+ if (ret)
+ return ret;
+
+ ret = ov8856_write_reg(ov8856, OV8856_OTP_MODE_CTRL,
+ OV8856_REG_VALUE_08BIT, OV8856_OTP_MODE_AUTO);
+ if (ret)
+ return ret;
+
+ return ov8856_write_reg(ov8856, OV8856_OTP_LOAD_CTRL,
+ OV8856_REG_VALUE_08BIT,
+ OV8856_OTP_LOAD_CTRL_ENABLE);
+}
+
static int ov8856_set_ctrl(struct v4l2_ctrl *ctrl)
{
struct ov8856 *ov8856 = container_of(ctrl->handler,
@@ -825,7 +1318,6 @@ static void ov8856_update_pad_format(const struct ov8856_mode *mode,
{
fmt->width = mode->width;
fmt->height = mode->height;
- fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10;
fmt->field = V4L2_FIELD_NONE;
}
@@ -834,6 +1326,7 @@ static int ov8856_start_streaming(struct ov8856 *ov8856)
struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
const struct ov8856_reg_list *reg_list;
int link_freq_index, ret;
+ u32 cur_h_size;
link_freq_index = ov8856->cur_mode->link_freq_index;
reg_list = &link_freq_configs[link_freq_index].reg_list;
@@ -850,6 +1343,28 @@ static int ov8856_start_streaming(struct ov8856 *ov8856)
return ret;
}
+ /* Update R3614 if the revision is 1B module */
+ if (ov8856->is_1B_revision) {
+ ret = ov8856_write_reg(ov8856, OV8856_ANAL_MODE_CTRL,
+ OV8856_REG_VALUE_08BIT,
+ OV8856_ANAL_1B_VAL);
+ if (ret) {
+ dev_err(&client->dev, "failed to set R3614");
+ return ret;
+ }
+ }
+
+ ret = ov8856_read_reg(ov8856, REG_X_ADDR_START,
+ OV8856_REG_VALUE_16BIT, &cur_h_size);
+ if (ret) {
+ dev_err(&client->dev, "failed to read out R3614");
+ return ret;
+ }
+
+ if (cur_h_size == X_OUTPUT_FULL_SIZE ||
+ cur_h_size == X_OUTPUT_BINNING_SIZE)
+ ov8856->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
+
ret = __v4l2_ctrl_handler_setup(ov8856->sd.ctrl_handler);
if (ret)
return ret;
@@ -908,6 +1423,44 @@ static int ov8856_set_stream(struct v4l2_subdev *sd, int enable)
return ret;
}
+static int __ov8856_power_on(struct ov8856 *ov8856)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&ov8856->sd);
+ int ret;
+
+ ret = clk_prepare_enable(ov8856->xvclk);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed to enable xvclk\n");
+ return ret;
+ }
+
+ gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, GPIOD_OUT_LOW);
+
+ ret = regulator_bulk_enable(OV8856_NUM_SUPPLIES, ov8856->supplies);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed to enable regulators\n");
+ goto disable_clk;
+ }
+
+ gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, GPIOD_OUT_HIGH);
+
+ usleep_range(1500, 1800);
+
+ return 0;
+
+disable_clk:
+ clk_disable_unprepare(ov8856->xvclk);
+
+ return ret;
+}
+
+static void __ov8856_power_off(struct ov8856 *ov8856)
+{
+ gpiod_set_value_cansleep(ov8856->n_shutdn_gpio, GPIOD_OUT_LOW);
+ regulator_bulk_disable(OV8856_NUM_SUPPLIES, ov8856->supplies);
+ clk_disable_unprepare(ov8856->xvclk);
+}
+
static int __maybe_unused ov8856_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
@@ -951,6 +1504,7 @@ static int ov8856_set_format(struct v4l2_subdev *sd,
struct v4l2_subdev_format *fmt)
{
struct ov8856 *ov8856 = to_ov8856(sd);
+ struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
const struct ov8856_mode *mode;
s32 vblank_def, h_blank;
@@ -960,7 +1514,9 @@ static int ov8856_set_format(struct v4l2_subdev *sd,
fmt->format.height);
mutex_lock(&ov8856->mutex);
- ov8856_update_pad_format(mode, &fmt->format);
+ mbus_fmt->code = ov8856->fmt.code;
+ ov8856_update_pad_format(mode, mbus_fmt);
+ ov8856->fmt = fmt->format;
if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
*v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format;
} else {
@@ -992,13 +1548,17 @@ static int ov8856_get_format(struct v4l2_subdev *sd,
struct v4l2_subdev_format *fmt)
{
struct ov8856 *ov8856 = to_ov8856(sd);
+ struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
mutex_lock(&ov8856->mutex);
- if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
fmt->format = *v4l2_subdev_get_try_format(&ov8856->sd, cfg,
fmt->pad);
- else
- ov8856_update_pad_format(ov8856->cur_mode, &fmt->format);
+ } else {
+ fmt->format = ov8856->fmt;
+ ov8856_update_pad_format(ov8856->cur_mode, mbus_fmt);
+ mbus_fmt->code = ov8856->fmt.code;
+ }
mutex_unlock(&ov8856->mutex);
@@ -1009,11 +1569,12 @@ static int ov8856_enum_mbus_code(struct v4l2_subdev *sd,
struct v4l2_subdev_pad_config *cfg,
struct v4l2_subdev_mbus_code_enum *code)
{
- /* Only one bayer order GRBG is supported */
+ struct ov8856 *ov8856 = to_ov8856(sd);
+
if (code->index > 0)
return -EINVAL;
- code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ code->code = ov8856->fmt.code;
return 0;
}
@@ -1089,6 +1650,20 @@ static int ov8856_identify_module(struct ov8856 *ov8856)
return -ENXIO;
}
+ /* check sensor hardware revision */
+ ret = ov8856_check_revision(ov8856);
+ if (ret) {
+ dev_err(&client->dev, "failed to check sensor revision");
+ return ret;
+ }
+
+ ret = ov8856_read_reg(ov8856, OV8856_MODULE_REVISION,
+ OV8856_REG_VALUE_08BIT, &val);
+ if (ret)
+ return ret;
+
+ ov8856->is_1B_revision = val == OV8856_1B_MODULE;
+
return 0;
}
@@ -1110,7 +1685,7 @@ static int ov8856_check_hwcfg(struct device *dev)
if (ret)
return ret;
- if (mclk != OV8856_MCLK) {
+ if (mclk != OV8856_XVCLK_19_2) {
dev_err(dev, "external clock %d is not supported", mclk);
return -EINVAL;
}
@@ -1167,6 +1742,9 @@ static int ov8856_remove(struct i2c_client *client)
media_entity_cleanup(&sd->entity);
v4l2_ctrl_handler_free(sd->ctrl_handler);
pm_runtime_disable(&client->dev);
+ if (!pm_runtime_status_suspended(&client->dev))
+ __ov8856_power_off(ov8856);
+ pm_runtime_set_suspended(&client->dev);
mutex_destroy(&ov8856->mutex);
return 0;
@@ -1175,6 +1753,7 @@ static int ov8856_remove(struct i2c_client *client)
static int ov8856_probe(struct i2c_client *client)
{
struct ov8856 *ov8856;
+ unsigned int i;
int ret;
ret = ov8856_check_hwcfg(&client->dev);
@@ -1189,6 +1768,42 @@ static int ov8856_probe(struct i2c_client *client)
return -ENOMEM;
v4l2_i2c_subdev_init(&ov8856->sd, client, &ov8856_subdev_ops);
+ ov8856->fmt.code = MEDIA_BUS_FMT_SGRBG10_1X10;
+
+ ov8856->xvclk = devm_clk_get(&client->dev, "xvclk");
+ if (IS_ERR(ov8856->xvclk)) {
+ dev_err(&client->dev, "failed to get xvclk\n");
+ return -EINVAL;
+ }
+
+ ret = clk_set_rate(ov8856->xvclk, OV8856_XVCLK_24);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed to set xvclk rate (24MHz)\n");
+ return ret;
+ }
+ if (clk_get_rate(ov8856->xvclk) != OV8856_XVCLK_24)
+ dev_warn(&client->dev,
+ "xvclk mismatched, modes are based on 24MHz\n");
+
+ ov8856->n_shutdn_gpio = devm_gpiod_get(&client->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(ov8856->n_shutdn_gpio)) {
+ dev_err(&client->dev, "failed to get reset-gpios\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < OV8856_NUM_SUPPLIES; i++)
+ ov8856->supplies[i].supply = ov8856_supply_names[i];
+
+ ret = devm_regulator_bulk_get(&client->dev, OV8856_NUM_SUPPLIES,
+ ov8856->supplies);
+ if (ret)
+ dev_warn(&client->dev, "failed to get regulators\n");
+
+ ret = __ov8856_power_on(ov8856);
+ if (ret)
+ dev_warn(&client->dev, "failed to power on\n");
+
ret = ov8856_identify_module(ov8856);
if (ret) {
dev_err(&client->dev, "failed to find sensor: %d", ret);
@@ -1241,8 +1856,29 @@ static int ov8856_probe(struct i2c_client *client)
return ret;
}
+static int __maybe_unused ov8856_runtime_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov8856 *ov8856 = to_ov8856(sd);
+
+ return __ov8856_power_on(ov8856);
+}
+
+static int __maybe_unused ov8856_runtime_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct ov8856 *ov8856 = to_ov8856(sd);
+
+ __ov8856_power_off(ov8856);
+
+ return 0;
+}
+
static const struct dev_pm_ops ov8856_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(ov8856_suspend, ov8856_resume)
+ SET_RUNTIME_PM_OPS(ov8856_runtime_suspend, ov8856_runtime_resume, NULL)
};
#ifdef CONFIG_ACPI
@@ -1254,11 +1890,18 @@ static const struct acpi_device_id ov8856_acpi_ids[] = {
MODULE_DEVICE_TABLE(acpi, ov8856_acpi_ids);
#endif
+static const struct of_device_id ov8856_of_match[] = {
+ { .compatible = "ovti,ov8856" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, ov8856_of_match);
+
static struct i2c_driver ov8856_i2c_driver = {
.driver = {
.name = "ov8856",
.pm = &ov8856_pm_ops,
.acpi_match_table = ACPI_PTR(ov8856_acpi_ids),
+ .of_match_table = ov8856_of_match,
},
.probe_new = ov8856_probe,
.remove = ov8856_remove,
--
2.9.2
next prev parent reply other threads:[~2019-10-31 9:02 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-31 9:02 [V3, 0/2] media: ov8856: Add YAML binding and sensor mode support Dongchun Zhu
2019-10-31 9:02 ` [V3, 1/2] media: dt-bindings: ov8856: Document YAML bindings Dongchun Zhu
2019-10-31 16:38 ` Rob Herring
2019-10-31 9:02 ` Dongchun Zhu [this message]
2019-10-31 17:04 ` [V3, 2/2] media: i2c: ov8856: Add support for more sensor modes Sakari Ailus
2019-11-25 9:33 ` Pi-Hsun Shih
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191031090213.27727-3-dongchun.zhu@mediatek.com \
--to=dongchun.zhu@mediatek.com \
--cc=andriy.shevchenko@linux.intel.com \
--cc=bingbu.cao@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=drinkcat@chromium.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=louis.kuo@mediatek.com \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=mchehab@kernel.org \
--cc=robh+dt@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=shengnan.wang@mediatek.com \
--cc=sj.huang@mediatek.com \
--cc=srv_heupstream@mediatek.com \
--cc=tfiga@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).