* [PATCH v3 0/2] Add IMX219 CMOS image sensor support
@ 2020-01-10 20:09 Andrey Konovalov
2020-01-10 20:09 ` [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Andrey Konovalov @ 2020-01-10 20:09 UTC (permalink / raw)
To: mchehab, robh+dt
Cc: linux-media, devicetree, peter.griffin, dave.stevenson, ezequiel,
sakari.ailus, Andrey Konovalov
This patchset adds support for IMX219 CMOS image sensor from Sony.
Sony IMX219 is an 8MPix, 1/4.0-inch CMOS active pixel digital image sensor
with an active array size of 3280H x 2464V. It is programmable through
I2C interface. Image data are sent through MIPI CSI-2, which can be configured
as either 2 or 4 data lanes, but this driver currently only supports 2 lanes.
The currently supported resolutions are 3280x2464 @ 15fps, 1920x1080 @ 30fps
(cropped FOV), and 1640x1232 (2x2 binned) @ 30fps.
The driver has been tested with Raspberry Pi Camera Module v2 connected to
Raspberry Pi Zero W.
Changes since v2 [1]:
dt-bindings:
- "clock-names" property removed
- "xclr-gpios" property renamed to "reset-gpios"
- the camera-clk mode moved out of sensor device node
- "clock-lanes" property removed (the sensor doesn't support lane reordering)
- "clock-noncontinuous" description made more clear (thanks Sakari)
- "data-lanes" property reworked: it is now optional, and if it is not
present the driver should assume four-lane operation. For two-lane
operation (the only mode supported by the current driver) this property
must be present and set to <1 2>
imx219 sensor driver:
- "xclr-gpios" property renamed to "reset-gpios", the corresponding
struct gpio_desc field in the imx219 structure is renamed to reset_gpio
- in the driver probe() a test to check that the number of CSI-2 data lanes
is supported by the driver was added
- devm_clk_get() is now called with NULL as the 2nd argument, as there is
just single clock, and there is no need to use clock ID
- error messages are added when the driver fails to get regulators, to init
media entity pads, or to register sensor sub-device
Thanks,
Andrey
[1] https://patchwork.kernel.org/cover/11311137/
Andrey Konovalov (1):
dt-bindings: media: i2c: Add IMX219 CMOS sensor binding
Dave Stevenson (1):
media: i2c: Add driver for Sony IMX219 sensor
.../devicetree/bindings/media/i2c/imx219.yaml | 104 ++
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 12 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/imx219.c | 1253 +++++++++++++++++
5 files changed, 1378 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.yaml
create mode 100644 drivers/media/i2c/imx219.c
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding
2020-01-10 20:09 [PATCH v3 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
@ 2020-01-10 20:09 ` Andrey Konovalov
2020-01-13 23:04 ` Rob Herring
2020-01-10 20:09 ` [PATCH v3 2/2] media: i2c: Add driver for Sony IMX219 sensor Andrey Konovalov
2020-01-11 4:45 ` [PATCH v3 0/2] Add IMX219 CMOS image sensor support Ezequiel Garcia
2 siblings, 1 reply; 6+ messages in thread
From: Andrey Konovalov @ 2020-01-10 20:09 UTC (permalink / raw)
To: mchehab, robh+dt
Cc: linux-media, devicetree, peter.griffin, dave.stevenson, ezequiel,
sakari.ailus, Andrey Konovalov
Add YAML device tree binding for IMX219 CMOS image sensor, and
the relevant MAINTAINERS entries.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
---
.../devicetree/bindings/media/i2c/imx219.yaml | 104 ++++++++++++++++++
MAINTAINERS | 8 ++
2 files changed, 112 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/imx219.yaml b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
new file mode 100644
index 000000000000..536766b63e39
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx219.yaml
@@ -0,0 +1,104 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/imx219.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
+
+maintainers:
+ - Dave Stevenson <dave.stevenson@raspberrypi.com>
+
+description: |-
+ The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
+ with an active array size of 3280H x 2464V. It is programmable through
+ I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
+ Image data is sent through MIPI CSI-2, which is configured as either 2 or
+ 4 data lanes.
+
+properties:
+ compatible:
+ const: sony,imx219
+
+ reg:
+ description: I2C device address
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ VDIG-supply:
+ description:
+ Digital I/O voltage supply, 1.8 volts
+
+ VANA-supply:
+ description:
+ Analog voltage supply, 2.8 volts
+
+ VDDL-supply:
+ description:
+ Digital core voltage supply, 1.2 volts
+
+ reset-gpios:
+ description: |-
+ Reference to the GPIO connected to the xclr pin, if any.
+ Must be released (set high) after all supplies are applied.
+
+ # See ../video-interfaces.txt for more details
+ port:
+ type: object
+ properties:
+ endpoint:
+ type: object
+ properties:
+ data-lanes:
+ description: |-
+ The sensor supports either two-lane, or four-lane operation.
+ If this property is omitted four-lane operation is assumed.
+ For two-lane operation the property must be set to <1 2>.
+ items:
+ - const: 1
+ - const: 2
+
+ clock-noncontinuous:
+ type: boolean
+ description: |-
+ MIPI CSI-2 clock is non-continuous if this property is present,
+ otherwise it's continuous.
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - VANA-supply
+ - VDIG-supply
+ - VDDL-supply
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ imx219: sensor@10 {
+ compatible = "sony,imx219";
+ reg = <0x10>;
+ clocks = <&imx219_clk>;
+ VANA-supply = <&imx219_vana>; /* 2.8v */
+ VDIG-supply = <&imx219_vdig>; /* 1.8v */
+ VDDL-supply = <&imx219_vddl>; /* 1.2v */
+
+ port {
+ imx219_0: endpoint {
+ remote-endpoint = <&csi1_ep>;
+ data-lanes = <1 2>;
+ clock-noncontinuous;
+ };
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 4017e6b760be..61b598f072e8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15351,6 +15351,14 @@ S: Maintained
F: drivers/media/i2c/imx214.c
F: Documentation/devicetree/bindings/media/i2c/sony,imx214.txt
+SONY IMX219 SENSOR DRIVER
+M: Dave Stevenson <dave.stevenson@raspberrypi.com>
+L: linux-media@vger.kernel.org
+T: git git://linuxtv.org/media_tree.git
+S: Maintained
+F: drivers/media/i2c/imx219.c
+F: Documentation/devicetree/bindings/media/i2c/imx219.yaml
+
SONY IMX258 SENSOR DRIVER
M: Sakari Ailus <sakari.ailus@linux.intel.com>
L: linux-media@vger.kernel.org
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/2] media: i2c: Add driver for Sony IMX219 sensor
2020-01-10 20:09 [PATCH v3 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
2020-01-10 20:09 ` [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
@ 2020-01-10 20:09 ` Andrey Konovalov
2020-01-11 4:45 ` [PATCH v3 0/2] Add IMX219 CMOS image sensor support Ezequiel Garcia
2 siblings, 0 replies; 6+ messages in thread
From: Andrey Konovalov @ 2020-01-10 20:09 UTC (permalink / raw)
To: mchehab, robh+dt
Cc: linux-media, devicetree, peter.griffin, dave.stevenson, ezequiel,
sakari.ailus, Andrey Konovalov
From: Dave Stevenson <dave.stevenson@raspberrypi.com>
Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
---
drivers/media/i2c/Kconfig | 12 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/imx219.c | 1253 ++++++++++++++++++++++++++++++++++++
3 files changed, 1266 insertions(+)
create mode 100644 drivers/media/i2c/imx219.c
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index c68e002d26ea..6fa5af1f72b9 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -591,6 +591,18 @@ config VIDEO_IMX214
To compile this driver as a module, choose M here: the
module will be called imx214.
+config VIDEO_IMX219
+ tristate "Sony IMX219 sensor support"
+ depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
+ depends on MEDIA_CAMERA_SUPPORT
+ select V4L2_FWNODE
+ help
+ This is a Video4Linux2 sensor driver for the Sony
+ IMX219 camera.
+
+ To compile this driver as a module, choose M here: the
+ module will be called imx219.
+
config VIDEO_IMX258
tristate "Sony IMX258 sensor support"
depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index c147bb9d28db..77bf7d0b691f 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -111,6 +111,7 @@ obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
obj-$(CONFIG_VIDEO_HI556) += hi556.o
obj-$(CONFIG_VIDEO_IMX214) += imx214.o
+obj-$(CONFIG_VIDEO_IMX219) += imx219.o
obj-$(CONFIG_VIDEO_IMX258) += imx258.o
obj-$(CONFIG_VIDEO_IMX274) += imx274.o
obj-$(CONFIG_VIDEO_IMX290) += imx290.o
diff --git a/drivers/media/i2c/imx219.c b/drivers/media/i2c/imx219.c
new file mode 100644
index 000000000000..263959fe851c
--- /dev/null
+++ b/drivers/media/i2c/imx219.c
@@ -0,0 +1,1253 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * A V4L2 driver for Sony IMX219 cameras.
+ * Copyright (C) 2019, Raspberry Pi (Trading) Ltd
+ *
+ * Based on Sony imx258 camera driver
+ * Copyright (C) 2018 Intel Corporation
+ *
+ * DT / fwnode changes, and regulator / GPIO control taken from imx214 driver
+ * Copyright 2018 Qtechnology A/S
+ *
+ * Flip handling taken from the Sony IMX319 driver.
+ * Copyright (C) 2018 Intel Corporation
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+#include <asm/unaligned.h>
+
+#define IMX219_REG_VALUE_08BIT 1
+#define IMX219_REG_VALUE_16BIT 2
+
+#define IMX219_REG_MODE_SELECT 0x0100
+#define IMX219_MODE_STANDBY 0x00
+#define IMX219_MODE_STREAMING 0x01
+
+/* Chip ID */
+#define IMX219_REG_CHIP_ID 0x0000
+#define IMX219_CHIP_ID 0x0219
+
+/* External clock frequency is 24.0M */
+#define IMX219_XCLK_FREQ 24000000
+
+/* Pixel rate is fixed at 182.4M for all the modes */
+#define IMX219_PIXEL_RATE 182400000
+
+/* V_TIMING internal */
+#define IMX219_REG_VTS 0x0160
+#define IMX219_VTS_15FPS 0x0dc6
+#define IMX219_VTS_30FPS_1080P 0x06e3
+#define IMX219_VTS_30FPS_BINNED 0x06e3
+#define IMX219_VTS_MAX 0xffff
+
+#define IMX219_VBLANK_MIN 4
+
+/*Frame Length Line*/
+#define IMX219_FLL_MIN 0x08a6
+#define IMX219_FLL_MAX 0xffff
+#define IMX219_FLL_STEP 1
+#define IMX219_FLL_DEFAULT 0x0c98
+
+/* HBLANK control - read only */
+#define IMX219_PPL_DEFAULT 3448
+
+/* Exposure control */
+#define IMX219_REG_EXPOSURE 0x015a
+#define IMX219_EXPOSURE_MIN 4
+#define IMX219_EXPOSURE_STEP 1
+#define IMX219_EXPOSURE_DEFAULT 0x640
+#define IMX219_EXPOSURE_MAX 65535
+
+/* Analog gain control */
+#define IMX219_REG_ANALOG_GAIN 0x0157
+#define IMX219_ANA_GAIN_MIN 0
+#define IMX219_ANA_GAIN_MAX 232
+#define IMX219_ANA_GAIN_STEP 1
+#define IMX219_ANA_GAIN_DEFAULT 0x0
+
+/* Digital gain control */
+#define IMX219_REG_DIGITAL_GAIN 0x0158
+#define IMX219_DGTL_GAIN_MIN 0x0100
+#define IMX219_DGTL_GAIN_MAX 0x0fff
+#define IMX219_DGTL_GAIN_DEFAULT 0x0100
+#define IMX219_DGTL_GAIN_STEP 1
+
+#define IMX219_REG_ORIENTATION 0x0172
+
+/* Test Pattern Control */
+#define IMX219_REG_TEST_PATTERN 0x0600
+#define IMX219_TEST_PATTERN_DISABLE 0
+#define IMX219_TEST_PATTERN_SOLID_COLOR 1
+#define IMX219_TEST_PATTERN_COLOR_BARS 2
+#define IMX219_TEST_PATTERN_GREY_COLOR 3
+#define IMX219_TEST_PATTERN_PN9 4
+
+/* Test pattern colour components */
+#define IMX219_REG_TESTP_RED 0x0602
+#define IMX219_REG_TESTP_GREENR 0x0604
+#define IMX219_REG_TESTP_BLUE 0x0606
+#define IMX219_REG_TESTP_GREENB 0x0608
+#define IMX219_TESTP_COLOUR_MIN 0
+#define IMX219_TESTP_COLOUR_MAX 0x03ff
+#define IMX219_TESTP_COLOUR_STEP 1
+#define IMX219_TESTP_RED_DEFAULT IMX219_TESTP_COLOUR_MAX
+#define IMX219_TESTP_GREENR_DEFAULT 0
+#define IMX219_TESTP_BLUE_DEFAULT 0
+#define IMX219_TESTP_GREENB_DEFAULT 0
+
+struct imx219_reg {
+ u16 address;
+ u8 val;
+};
+
+struct imx219_reg_list {
+ unsigned int num_of_regs;
+ const struct imx219_reg *regs;
+};
+
+/* Mode : resolution and related config&values */
+struct imx219_mode {
+ /* Frame width */
+ unsigned int width;
+ /* Frame height */
+ unsigned int height;
+
+ /* V-timing */
+ unsigned int vts_def;
+
+ /* Default register values */
+ struct imx219_reg_list reg_list;
+};
+
+/*
+ * Register sets lifted off the i2C interface from the Raspberry Pi firmware
+ * driver.
+ * 3280x2464 = mode 2, 1920x1080 = mode 1, and 1640x1232 = mode 4.
+ */
+static const struct imx219_reg mode_3280x2464_regs[] = {
+ {0x0100, 0x00},
+ {0x30eb, 0x0c},
+ {0x30eb, 0x05},
+ {0x300a, 0xff},
+ {0x300b, 0xff},
+ {0x30eb, 0x05},
+ {0x30eb, 0x09},
+ {0x0114, 0x01},
+ {0x0128, 0x00},
+ {0x012a, 0x18},
+ {0x012b, 0x00},
+ {0x0164, 0x00},
+ {0x0165, 0x00},
+ {0x0166, 0x0c},
+ {0x0167, 0xcf},
+ {0x0168, 0x00},
+ {0x0169, 0x00},
+ {0x016a, 0x09},
+ {0x016b, 0x9f},
+ {0x016c, 0x0c},
+ {0x016d, 0xd0},
+ {0x016e, 0x09},
+ {0x016f, 0xa0},
+ {0x0170, 0x01},
+ {0x0171, 0x01},
+ {0x0174, 0x00},
+ {0x0175, 0x00},
+ {0x018c, 0x0a},
+ {0x018d, 0x0a},
+ {0x0301, 0x05},
+ {0x0303, 0x01},
+ {0x0304, 0x03},
+ {0x0305, 0x03},
+ {0x0306, 0x00},
+ {0x0307, 0x39},
+ {0x0309, 0x0a},
+ {0x030b, 0x01},
+ {0x030c, 0x00},
+ {0x030d, 0x72},
+ {0x0624, 0x0c},
+ {0x0625, 0xd0},
+ {0x0626, 0x09},
+ {0x0627, 0xa0},
+ {0x455e, 0x00},
+ {0x471e, 0x4b},
+ {0x4767, 0x0f},
+ {0x4750, 0x14},
+ {0x4540, 0x00},
+ {0x47b4, 0x14},
+ {0x4713, 0x30},
+ {0x478b, 0x10},
+ {0x478f, 0x10},
+ {0x4793, 0x10},
+ {0x4797, 0x0e},
+ {0x479b, 0x0e},
+ {0x0162, 0x0d},
+ {0x0163, 0x78},
+};
+
+static const struct imx219_reg mode_1920_1080_regs[] = {
+ {0x0100, 0x00},
+ {0x30eb, 0x05},
+ {0x30eb, 0x0c},
+ {0x300a, 0xff},
+ {0x300b, 0xff},
+ {0x30eb, 0x05},
+ {0x30eb, 0x09},
+ {0x0114, 0x01},
+ {0x0128, 0x00},
+ {0x012a, 0x18},
+ {0x012b, 0x00},
+ {0x0162, 0x0d},
+ {0x0163, 0x78},
+ {0x0164, 0x02},
+ {0x0165, 0xa8},
+ {0x0166, 0x0a},
+ {0x0167, 0x27},
+ {0x0168, 0x02},
+ {0x0169, 0xb4},
+ {0x016a, 0x06},
+ {0x016b, 0xeb},
+ {0x016c, 0x07},
+ {0x016d, 0x80},
+ {0x016e, 0x04},
+ {0x016f, 0x38},
+ {0x0170, 0x01},
+ {0x0171, 0x01},
+ {0x0174, 0x00},
+ {0x0175, 0x00},
+ {0x018c, 0x0a},
+ {0x018d, 0x0a},
+ {0x0301, 0x05},
+ {0x0303, 0x01},
+ {0x0304, 0x03},
+ {0x0305, 0x03},
+ {0x0306, 0x00},
+ {0x0307, 0x39},
+ {0x0309, 0x0a},
+ {0x030b, 0x01},
+ {0x030c, 0x00},
+ {0x030d, 0x72},
+ {0x0624, 0x07},
+ {0x0625, 0x80},
+ {0x0626, 0x04},
+ {0x0627, 0x38},
+ {0x455e, 0x00},
+ {0x471e, 0x4b},
+ {0x4767, 0x0f},
+ {0x4750, 0x14},
+ {0x4540, 0x00},
+ {0x47b4, 0x14},
+ {0x4713, 0x30},
+ {0x478b, 0x10},
+ {0x478f, 0x10},
+ {0x4793, 0x10},
+ {0x4797, 0x0e},
+ {0x479b, 0x0e},
+ {0x0162, 0x0d},
+ {0x0163, 0x78},
+};
+
+static const struct imx219_reg mode_1640_1232_regs[] = {
+ {0x0100, 0x00},
+ {0x30eb, 0x0c},
+ {0x30eb, 0x05},
+ {0x300a, 0xff},
+ {0x300b, 0xff},
+ {0x30eb, 0x05},
+ {0x30eb, 0x09},
+ {0x0114, 0x01},
+ {0x0128, 0x00},
+ {0x012a, 0x18},
+ {0x012b, 0x00},
+ {0x0164, 0x00},
+ {0x0165, 0x00},
+ {0x0166, 0x0c},
+ {0x0167, 0xcf},
+ {0x0168, 0x00},
+ {0x0169, 0x00},
+ {0x016a, 0x09},
+ {0x016b, 0x9f},
+ {0x016c, 0x06},
+ {0x016d, 0x68},
+ {0x016e, 0x04},
+ {0x016f, 0xd0},
+ {0x0170, 0x01},
+ {0x0171, 0x01},
+ {0x0174, 0x01},
+ {0x0175, 0x01},
+ {0x018c, 0x0a},
+ {0x018d, 0x0a},
+ {0x0301, 0x05},
+ {0x0303, 0x01},
+ {0x0304, 0x03},
+ {0x0305, 0x03},
+ {0x0306, 0x00},
+ {0x0307, 0x39},
+ {0x0309, 0x0a},
+ {0x030b, 0x01},
+ {0x030c, 0x00},
+ {0x030d, 0x72},
+ {0x0624, 0x06},
+ {0x0625, 0x68},
+ {0x0626, 0x04},
+ {0x0627, 0xd0},
+ {0x455e, 0x00},
+ {0x471e, 0x4b},
+ {0x4767, 0x0f},
+ {0x4750, 0x14},
+ {0x4540, 0x00},
+ {0x47b4, 0x14},
+ {0x4713, 0x30},
+ {0x478b, 0x10},
+ {0x478f, 0x10},
+ {0x4793, 0x10},
+ {0x4797, 0x0e},
+ {0x479b, 0x0e},
+ {0x0162, 0x0d},
+ {0x0163, 0x78},
+};
+
+static const char * const imx219_test_pattern_menu[] = {
+ "Disabled",
+ "Color Bars",
+ "Solid Color",
+ "Grey Color Bars",
+ "PN9"
+};
+
+static const int imx219_test_pattern_val[] = {
+ IMX219_TEST_PATTERN_DISABLE,
+ IMX219_TEST_PATTERN_COLOR_BARS,
+ IMX219_TEST_PATTERN_SOLID_COLOR,
+ IMX219_TEST_PATTERN_GREY_COLOR,
+ IMX219_TEST_PATTERN_PN9,
+};
+
+/* regulator supplies */
+static const char * const imx219_supply_name[] = {
+ /* Supplies can be enabled in any order */
+ "VANA", /* Analog (2.8V) supply */
+ "VDIG", /* Digital Core (1.8V) supply */
+ "VDDL", /* IF (1.2V) supply */
+};
+
+#define IMX219_NUM_SUPPLIES ARRAY_SIZE(imx219_supply_name)
+
+#define IMX219_XCLR_DELAY_MS 10 /* Initialisation delay after XCLR low->high */
+
+/* Mode configs */
+static const struct imx219_mode supported_modes[] = {
+ {
+ /* 8MPix 15fps mode */
+ .width = 3280,
+ .height = 2464,
+ .vts_def = IMX219_VTS_15FPS,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(mode_3280x2464_regs),
+ .regs = mode_3280x2464_regs,
+ },
+ },
+ {
+ /* 1080P 30fps cropped */
+ .width = 1920,
+ .height = 1080,
+ .vts_def = IMX219_VTS_30FPS_1080P,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(mode_1920_1080_regs),
+ .regs = mode_1920_1080_regs,
+ },
+ },
+ {
+ /* 2x2 binned 30fps mode */
+ .width = 1640,
+ .height = 1232,
+ .vts_def = IMX219_VTS_30FPS_BINNED,
+ .reg_list = {
+ .num_of_regs = ARRAY_SIZE(mode_1640_1232_regs),
+ .regs = mode_1640_1232_regs,
+ },
+ },
+};
+
+struct imx219 {
+ struct device *dev;
+
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+
+ struct v4l2_fwnode_endpoint ep; /* the parsed DT endpoint info */
+ struct clk *xclk; /* system clock to IMX219 */
+ u32 xclk_freq;
+
+ struct gpio_desc *reset_gpio;
+ struct regulator_bulk_data supplies[IMX219_NUM_SUPPLIES];
+
+ struct v4l2_ctrl_handler ctrl_handler;
+ /* V4L2 Controls */
+ struct v4l2_ctrl *pixel_rate;
+ struct v4l2_ctrl *exposure;
+ struct v4l2_ctrl *vflip;
+ struct v4l2_ctrl *hflip;
+ struct v4l2_ctrl *vblank;
+ struct v4l2_ctrl *hblank;
+
+ /* Current mode */
+ const struct imx219_mode *mode;
+
+ /*
+ * Mutex for serialized access:
+ * Protect sensor module set pad format and start/stop streaming safely.
+ */
+ struct mutex mutex;
+
+ /* Streaming on/off */
+ bool streaming;
+};
+
+static inline struct imx219 *to_imx219(struct v4l2_subdev *_sd)
+{
+ return container_of(_sd, struct imx219, sd);
+}
+
+/* Read registers up to 2 at a time */
+static int imx219_read_reg(struct imx219 *imx219, u16 reg, u32 len, u32 *val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ struct i2c_msg msgs[2];
+ u8 addr_buf[2] = { reg >> 8, reg & 0xff };
+ u8 data_buf[4] = { 0, };
+ int ret;
+
+ if (len > 4)
+ return -EINVAL;
+
+ /* Write register address */
+ msgs[0].addr = client->addr;
+ msgs[0].flags = 0;
+ msgs[0].len = ARRAY_SIZE(addr_buf);
+ msgs[0].buf = addr_buf;
+
+ /* Read data from register */
+ msgs[1].addr = client->addr;
+ msgs[1].flags = I2C_M_RD;
+ msgs[1].len = len;
+ msgs[1].buf = &data_buf[4 - len];
+
+ ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+ if (ret != ARRAY_SIZE(msgs))
+ return -EIO;
+
+ *val = get_unaligned_be32(data_buf);
+
+ return 0;
+}
+
+/* Write registers up to 2 at a time */
+static int imx219_write_reg(struct imx219 *imx219, u16 reg, u32 len, u32 val)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ u8 buf[6];
+
+ if (len > 4)
+ return -EINVAL;
+
+ put_unaligned_be16(reg, buf);
+ put_unaligned_be32(val << (8 * (4 - len)), buf + 2);
+ if (i2c_master_send(client, buf, len + 2) != len + 2)
+ return -EIO;
+
+ return 0;
+}
+
+/* Write a list of registers */
+static int imx219_write_regs(struct imx219 *imx219,
+ const struct imx219_reg *regs, u32 len)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < len; i++) {
+ ret = imx219_write_reg(imx219, regs[i].address, 1, regs[i].val);
+ if (ret) {
+ dev_err_ratelimited(&client->dev,
+ "Failed to write reg 0x%4.4x. error = %d\n",
+ regs[i].address, ret);
+
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+/* Get bayer order based on flip setting. */
+static u32 imx219_get_format_code(struct imx219 *imx219)
+{
+ /*
+ * Only one bayer order is supported.
+ * It depends on the flip settings.
+ */
+ static const u32 codes[2][2] = {
+ { MEDIA_BUS_FMT_SRGGB10_1X10, MEDIA_BUS_FMT_SGRBG10_1X10, },
+ { MEDIA_BUS_FMT_SGBRG10_1X10, MEDIA_BUS_FMT_SBGGR10_1X10, },
+ };
+
+ lockdep_assert_held(&imx219->mutex);
+ return codes[imx219->vflip->val][imx219->hflip->val];
+}
+
+static int imx219_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+ struct v4l2_mbus_framefmt *try_fmt =
+ v4l2_subdev_get_try_format(sd, fh->pad, 0);
+
+ mutex_lock(&imx219->mutex);
+
+ /* Initialize try_fmt */
+ try_fmt->width = supported_modes[0].width;
+ try_fmt->height = supported_modes[0].height;
+ try_fmt->code = imx219_get_format_code(imx219);
+ try_fmt->field = V4L2_FIELD_NONE;
+
+ mutex_unlock(&imx219->mutex);
+
+ return 0;
+}
+
+static int imx219_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct imx219 *imx219 =
+ container_of(ctrl->handler, struct imx219, ctrl_handler);
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ int ret;
+
+ if (ctrl->id == V4L2_CID_VBLANK) {
+ int exposure_max, exposure_def;
+
+ /* Update max exposure while meeting expected vblanking */
+ exposure_max = imx219->mode->height + ctrl->val - 4;
+ exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ?
+ exposure_max : IMX219_EXPOSURE_DEFAULT;
+ __v4l2_ctrl_modify_range(imx219->exposure,
+ imx219->exposure->minimum,
+ exposure_max, imx219->exposure->step,
+ exposure_def);
+ }
+
+ /*
+ * Applying V4L2 control value only happens
+ * when power is up for streaming
+ */
+ if (pm_runtime_get_if_in_use(&client->dev) == 0)
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_ANALOGUE_GAIN:
+ ret = imx219_write_reg(imx219, IMX219_REG_ANALOG_GAIN,
+ IMX219_REG_VALUE_08BIT, ctrl->val);
+ break;
+ case V4L2_CID_EXPOSURE:
+ ret = imx219_write_reg(imx219, IMX219_REG_EXPOSURE,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ case V4L2_CID_DIGITAL_GAIN:
+ ret = imx219_write_reg(imx219, IMX219_REG_DIGITAL_GAIN,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN:
+ ret = imx219_write_reg(imx219, IMX219_REG_TEST_PATTERN,
+ IMX219_REG_VALUE_16BIT,
+ imx219_test_pattern_val[ctrl->val]);
+ break;
+ case V4L2_CID_HFLIP:
+ case V4L2_CID_VFLIP:
+ ret = imx219_write_reg(imx219, IMX219_REG_ORIENTATION, 1,
+ imx219->hflip->val |
+ imx219->vflip->val << 1);
+ break;
+ case V4L2_CID_VBLANK:
+ ret = imx219_write_reg(imx219, IMX219_REG_VTS,
+ IMX219_REG_VALUE_16BIT,
+ imx219->mode->height + ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN_RED:
+ ret = imx219_write_reg(imx219, IMX219_REG_TESTP_RED,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN_GREENR:
+ ret = imx219_write_reg(imx219, IMX219_REG_TESTP_GREENR,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN_BLUE:
+ ret = imx219_write_reg(imx219, IMX219_REG_TESTP_BLUE,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ case V4L2_CID_TEST_PATTERN_GREENB:
+ ret = imx219_write_reg(imx219, IMX219_REG_TESTP_GREENB,
+ IMX219_REG_VALUE_16BIT, ctrl->val);
+ break;
+ default:
+ dev_info(&client->dev,
+ "ctrl(id:0x%x,val:0x%x) is not handled\n",
+ ctrl->id, ctrl->val);
+ ret = -EINVAL;
+ break;
+ }
+
+ pm_runtime_put(&client->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops imx219_ctrl_ops = {
+ .s_ctrl = imx219_set_ctrl,
+};
+
+static int imx219_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+
+ /*
+ * Only one bayer order is supported (though it depends on the flip
+ * settings)
+ */
+ if (code->index > 0)
+ return -EINVAL;
+
+ code->code = imx219_get_format_code(imx219);
+
+ return 0;
+}
+
+static int imx219_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+
+ if (fse->index >= ARRAY_SIZE(supported_modes))
+ return -EINVAL;
+
+ if (fse->code != imx219_get_format_code(imx219))
+ return -EINVAL;
+
+ fse->min_width = supported_modes[fse->index].width;
+ fse->max_width = fse->min_width;
+ fse->min_height = supported_modes[fse->index].height;
+ fse->max_height = fse->min_height;
+
+ return 0;
+}
+
+static void imx219_reset_colorspace(struct v4l2_mbus_framefmt *fmt)
+{
+ fmt->colorspace = V4L2_COLORSPACE_SRGB;
+ fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace);
+ fmt->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(true,
+ fmt->colorspace,
+ fmt->ycbcr_enc);
+ fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace);
+}
+
+static void imx219_update_pad_format(struct imx219 *imx219,
+ const struct imx219_mode *mode,
+ struct v4l2_subdev_format *fmt)
+{
+ fmt->format.width = mode->width;
+ fmt->format.height = mode->height;
+ fmt->format.code = imx219_get_format_code(imx219);
+ fmt->format.field = V4L2_FIELD_NONE;
+
+ imx219_reset_colorspace(&fmt->format);
+}
+
+static int __imx219_get_pad_format(struct imx219 *imx219,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY)
+ fmt->format = *v4l2_subdev_get_try_format(&imx219->sd, cfg,
+ fmt->pad);
+ else
+ imx219_update_pad_format(imx219, imx219->mode, fmt);
+
+ return 0;
+}
+
+static int imx219_get_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+ int ret;
+
+ mutex_lock(&imx219->mutex);
+ ret = __imx219_get_pad_format(imx219, cfg, fmt);
+ mutex_unlock(&imx219->mutex);
+
+ return ret;
+}
+
+static int imx219_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *fmt)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+ const struct imx219_mode *mode;
+ struct v4l2_mbus_framefmt *framefmt;
+ int exposure_max, exposure_def, hblank;
+
+ mutex_lock(&imx219->mutex);
+
+ /* Bayer order varies with flips */
+ fmt->format.code = imx219_get_format_code(imx219);
+
+ mode = v4l2_find_nearest_size(supported_modes,
+ ARRAY_SIZE(supported_modes),
+ width, height,
+ fmt->format.width, fmt->format.height);
+ imx219_update_pad_format(imx219, mode, fmt);
+ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
+ framefmt = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
+ *framefmt = fmt->format;
+ } else if (imx219->mode != mode) {
+ imx219->mode = mode;
+ /* Update limits and set FPS to default */
+ __v4l2_ctrl_modify_range(imx219->vblank, IMX219_VBLANK_MIN,
+ IMX219_VTS_MAX - mode->height, 1,
+ mode->vts_def - mode->height);
+ __v4l2_ctrl_s_ctrl(imx219->vblank,
+ mode->vts_def - mode->height);
+ /* Update max exposure while meeting expected vblanking */
+ exposure_max = mode->vts_def - 4;
+ exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ?
+ exposure_max : IMX219_EXPOSURE_DEFAULT;
+ __v4l2_ctrl_modify_range(imx219->exposure,
+ imx219->exposure->minimum,
+ exposure_max, imx219->exposure->step,
+ exposure_def);
+ /*
+ * Currently PPL is fixed to IMX219_PPL_DEFAULT, so hblank
+ * depends on mode->width only, and is not changeble in any
+ * way other than changing the mode.
+ */
+ hblank = IMX219_PPL_DEFAULT - mode->width;
+ __v4l2_ctrl_modify_range(imx219->hblank, hblank, hblank, 1,
+ hblank);
+ }
+
+ mutex_unlock(&imx219->mutex);
+
+ return 0;
+}
+
+static int imx219_start_streaming(struct imx219 *imx219)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ const struct imx219_reg_list *reg_list;
+ int ret;
+
+ /* Apply default values of current mode */
+ reg_list = &imx219->mode->reg_list;
+ ret = imx219_write_regs(imx219, reg_list->regs, reg_list->num_of_regs);
+ if (ret) {
+ dev_err(&client->dev, "%s failed to set mode\n", __func__);
+ return ret;
+ }
+
+ /* Apply customized values from user */
+ ret = __v4l2_ctrl_handler_setup(imx219->sd.ctrl_handler);
+ if (ret)
+ return ret;
+
+ /* set stream on register */
+ return imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+ IMX219_REG_VALUE_08BIT, IMX219_MODE_STREAMING);
+}
+
+static void imx219_stop_streaming(struct imx219 *imx219)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ int ret;
+
+ /* set stream off register */
+ ret = imx219_write_reg(imx219, IMX219_REG_MODE_SELECT,
+ IMX219_REG_VALUE_08BIT, IMX219_MODE_STANDBY);
+ if (ret)
+ dev_err(&client->dev, "%s failed to set stream\n", __func__);
+}
+
+static int imx219_set_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct imx219 *imx219 = to_imx219(sd);
+ struct i2c_client *client = v4l2_get_subdevdata(sd);
+ int ret = 0;
+
+ mutex_lock(&imx219->mutex);
+ if (imx219->streaming == enable) {
+ mutex_unlock(&imx219->mutex);
+ return 0;
+ }
+
+ if (enable) {
+ ret = pm_runtime_get_sync(&client->dev);
+ if (ret < 0) {
+ pm_runtime_put_noidle(&client->dev);
+ goto err_unlock;
+ }
+
+ /*
+ * Apply default & customized values
+ * and then start streaming.
+ */
+ ret = imx219_start_streaming(imx219);
+ if (ret)
+ goto err_rpm_put;
+ } else {
+ imx219_stop_streaming(imx219);
+ pm_runtime_put(&client->dev);
+ }
+
+ imx219->streaming = enable;
+
+ /* vflip and hflip cannot change during streaming */
+ __v4l2_ctrl_grab(imx219->vflip, enable);
+ __v4l2_ctrl_grab(imx219->hflip, enable);
+
+ mutex_unlock(&imx219->mutex);
+
+ return ret;
+
+err_rpm_put:
+ pm_runtime_put(&client->dev);
+err_unlock:
+ mutex_unlock(&imx219->mutex);
+
+ return ret;
+}
+
+/* Power/clock management functions */
+static int imx219_power_on(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx219 *imx219 = to_imx219(sd);
+ int ret;
+
+ ret = regulator_bulk_enable(IMX219_NUM_SUPPLIES,
+ imx219->supplies);
+ if (ret) {
+ dev_err(&client->dev, "%s: failed to enable regulators\n",
+ __func__);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(imx219->xclk);
+ if (ret) {
+ dev_err(&client->dev, "%s: failed to enable clock\n",
+ __func__);
+ goto reg_off;
+ }
+
+ gpiod_set_value_cansleep(imx219->reset_gpio, 1);
+ msleep(IMX219_XCLR_DELAY_MS);
+
+ return 0;
+reg_off:
+ regulator_bulk_disable(IMX219_NUM_SUPPLIES, imx219->supplies);
+ return ret;
+}
+
+static int imx219_power_off(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx219 *imx219 = to_imx219(sd);
+
+ gpiod_set_value_cansleep(imx219->reset_gpio, 0);
+ regulator_bulk_disable(IMX219_NUM_SUPPLIES, imx219->supplies);
+ clk_disable_unprepare(imx219->xclk);
+
+ return 0;
+}
+
+static int __maybe_unused imx219_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx219 *imx219 = to_imx219(sd);
+
+ if (imx219->streaming)
+ imx219_stop_streaming(imx219);
+
+ return 0;
+}
+
+static int __maybe_unused imx219_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx219 *imx219 = to_imx219(sd);
+ int ret;
+
+ if (imx219->streaming) {
+ ret = imx219_start_streaming(imx219);
+ if (ret)
+ goto error;
+ }
+
+ return 0;
+
+error:
+ imx219_stop_streaming(imx219);
+ imx219->streaming = 0;
+ return ret;
+}
+
+static int imx219_get_regulators(struct imx219 *imx219)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ int i;
+
+ for (i = 0; i < IMX219_NUM_SUPPLIES; i++)
+ imx219->supplies[i].supply = imx219_supply_name[i];
+
+ return devm_regulator_bulk_get(&client->dev,
+ IMX219_NUM_SUPPLIES,
+ imx219->supplies);
+}
+
+/* Verify chip ID */
+static int imx219_identify_module(struct imx219 *imx219)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ int ret;
+ u32 val;
+
+ ret = imx219_read_reg(imx219, IMX219_REG_CHIP_ID,
+ IMX219_REG_VALUE_16BIT, &val);
+ if (ret) {
+ dev_err(&client->dev, "failed to read chip id %x\n",
+ IMX219_CHIP_ID);
+ return ret;
+ }
+
+ if (val != IMX219_CHIP_ID) {
+ dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
+ IMX219_CHIP_ID, val);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static const struct v4l2_subdev_core_ops imx219_core_ops = {
+ .subscribe_event = v4l2_ctrl_subdev_subscribe_event,
+ .unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops imx219_video_ops = {
+ .s_stream = imx219_set_stream,
+};
+
+static const struct v4l2_subdev_pad_ops imx219_pad_ops = {
+ .enum_mbus_code = imx219_enum_mbus_code,
+ .get_fmt = imx219_get_pad_format,
+ .set_fmt = imx219_set_pad_format,
+ .enum_frame_size = imx219_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops imx219_subdev_ops = {
+ .core = &imx219_core_ops,
+ .video = &imx219_video_ops,
+ .pad = &imx219_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops imx219_internal_ops = {
+ .open = imx219_open,
+};
+
+/* Initialize control handlers */
+static int imx219_init_controls(struct imx219 *imx219)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&imx219->sd);
+ struct v4l2_ctrl_handler *ctrl_hdlr;
+ unsigned int height = imx219->mode->height;
+ int exposure_max, exposure_def, hblank;
+ int i, ret;
+
+ ctrl_hdlr = &imx219->ctrl_handler;
+ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 9);
+ if (ret)
+ return ret;
+
+ mutex_init(&imx219->mutex);
+ ctrl_hdlr->lock = &imx219->mutex;
+
+ /* By default, PIXEL_RATE is read only */
+ imx219->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_PIXEL_RATE,
+ IMX219_PIXEL_RATE,
+ IMX219_PIXEL_RATE, 1,
+ IMX219_PIXEL_RATE);
+
+ /* Initial vblank/hblank/exposure parameters based on current mode */
+ imx219->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_VBLANK, IMX219_VBLANK_MIN,
+ IMX219_VTS_MAX - height, 1,
+ imx219->mode->vts_def - height);
+ hblank = IMX219_PPL_DEFAULT - imx219->mode->width;
+ imx219->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_HBLANK, hblank, hblank,
+ 1, hblank);
+ if (imx219->hblank)
+ imx219->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+ exposure_max = imx219->mode->vts_def - 4;
+ exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ?
+ exposure_max : IMX219_EXPOSURE_DEFAULT;
+ imx219->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_EXPOSURE,
+ IMX219_EXPOSURE_MIN, exposure_max,
+ IMX219_EXPOSURE_STEP,
+ exposure_def);
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+ IMX219_ANA_GAIN_MIN, IMX219_ANA_GAIN_MAX,
+ IMX219_ANA_GAIN_STEP, IMX219_ANA_GAIN_DEFAULT);
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+ IMX219_DGTL_GAIN_MIN, IMX219_DGTL_GAIN_MAX,
+ IMX219_DGTL_GAIN_STEP, IMX219_DGTL_GAIN_DEFAULT);
+
+ imx219->hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_HFLIP, 0, 1, 1, 0);
+ if (imx219->hflip)
+ imx219->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+
+ imx219->vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_VFLIP, 0, 1, 1, 0);
+ if (imx219->vflip)
+ imx219->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+
+ v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(imx219_test_pattern_menu) - 1,
+ 0, 0, imx219_test_pattern_menu);
+ for (i = 0; i < 4; i++) {
+ /*
+ * The assumption is that
+ * V4L2_CID_TEST_PATTERN_GREENR == V4L2_CID_TEST_PATTERN_RED + 1
+ * V4L2_CID_TEST_PATTERN_BLUE == V4L2_CID_TEST_PATTERN_RED + 2
+ * V4L2_CID_TEST_PATTERN_GREENB == V4L2_CID_TEST_PATTERN_RED + 3
+ */
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx219_ctrl_ops,
+ V4L2_CID_TEST_PATTERN_RED + i,
+ IMX219_TESTP_COLOUR_MIN,
+ IMX219_TESTP_COLOUR_MAX,
+ IMX219_TESTP_COLOUR_STEP,
+ IMX219_TESTP_COLOUR_MAX);
+ /* The "Solid color" pattern is white by default */
+ }
+
+ if (ctrl_hdlr->error) {
+ ret = ctrl_hdlr->error;
+ dev_err(&client->dev, "%s control init failed (%d)\n",
+ __func__, ret);
+ goto error;
+ }
+
+ imx219->sd.ctrl_handler = ctrl_hdlr;
+
+ return 0;
+
+error:
+ v4l2_ctrl_handler_free(ctrl_hdlr);
+ mutex_destroy(&imx219->mutex);
+
+ return ret;
+}
+
+static void imx219_free_controls(struct imx219 *imx219)
+{
+ v4l2_ctrl_handler_free(imx219->sd.ctrl_handler);
+ mutex_destroy(&imx219->mutex);
+}
+
+static int imx219_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct fwnode_handle *endpoint;
+ struct imx219 *imx219;
+ int ret;
+
+ imx219 = devm_kzalloc(&client->dev, sizeof(*imx219), GFP_KERNEL);
+ if (!imx219)
+ return -ENOMEM;
+
+ imx219->dev = dev;
+
+ v4l2_i2c_subdev_init(&imx219->sd, client, &imx219_subdev_ops);
+
+ /* Get CSI2 bus config */
+ endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev),
+ NULL);
+ if (!endpoint) {
+ dev_err(dev, "endpoint node not found\n");
+ return -EINVAL;
+ }
+
+ ret = v4l2_fwnode_endpoint_parse(endpoint, &imx219->ep);
+ fwnode_handle_put(endpoint);
+ if (ret) {
+ dev_err(dev, "could not parse endpoint\n");
+ return ret;
+ }
+
+ /* Check the number of MIPI CSI2 data lanes */
+ if (imx219->ep.bus_type != V4L2_MBUS_CSI2_DPHY ||
+ imx219->ep.bus.mipi_csi2.num_data_lanes != 2) {
+ dev_err(dev, "only 2 data lanes are currently supported\n");
+ return -EINVAL;
+ }
+
+ /* Get system clock (xclk) */
+ imx219->xclk = devm_clk_get(dev, NULL);
+ if (IS_ERR(imx219->xclk)) {
+ dev_err(dev, "failed to get xclk\n");
+ return PTR_ERR(imx219->xclk);
+ }
+
+ imx219->xclk_freq = clk_get_rate(imx219->xclk);
+ if (imx219->xclk_freq != IMX219_XCLK_FREQ) {
+ dev_err(dev, "xclk frequency not supported: %d Hz\n",
+ imx219->xclk_freq);
+ return -EINVAL;
+ }
+
+ ret = imx219_get_regulators(imx219);
+ if (ret) {
+ dev_err(dev, "failed to get regulators\n");
+ return ret;
+ }
+
+ /* Request optional enable pin */
+ imx219->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+ GPIOD_OUT_HIGH);
+
+ /*
+ * The sensor must be powered for imx219_identify_module()
+ * to be able to read the CHIP_ID register
+ */
+ ret = imx219_power_on(dev);
+ if (ret)
+ return ret;
+
+ ret = imx219_identify_module(imx219);
+ if (ret)
+ goto error_power_off;
+
+ /* Set default mode to max resolution */
+ imx219->mode = &supported_modes[0];
+
+ ret = imx219_init_controls(imx219);
+ if (ret)
+ goto error_power_off;
+
+ /* Initialize subdev */
+ imx219->sd.internal_ops = &imx219_internal_ops;
+ imx219->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ imx219->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+
+ /* Initialize source pad */
+ imx219->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&imx219->sd.entity, 1, &imx219->pad);
+ if (ret) {
+ dev_err(dev, "failed to init entity pads: %d\n", ret);
+ goto error_handler_free;
+ }
+
+ ret = v4l2_async_register_subdev_sensor_common(&imx219->sd);
+ if (ret < 0) {
+ dev_err(dev, "failed to register sensor sub-device: %d\n", ret);
+ goto error_media_entity;
+ }
+
+ /* Enable runtime PM and turn off the device */
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+ pm_runtime_idle(dev);
+
+ return 0;
+
+error_media_entity:
+ media_entity_cleanup(&imx219->sd.entity);
+
+error_handler_free:
+ imx219_free_controls(imx219);
+
+error_power_off:
+ imx219_power_off(dev);
+
+ return ret;
+}
+
+static int imx219_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx219 *imx219 = to_imx219(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ media_entity_cleanup(&sd->entity);
+ imx219_free_controls(imx219);
+
+ pm_runtime_disable(&client->dev);
+ pm_runtime_set_suspended(&client->dev);
+
+ return 0;
+}
+
+static const struct of_device_id imx219_dt_ids[] = {
+ { .compatible = "sony,imx219" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx219_dt_ids);
+
+static const struct dev_pm_ops imx219_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(imx219_suspend, imx219_resume)
+ SET_RUNTIME_PM_OPS(imx219_power_off, imx219_power_on, NULL)
+};
+
+static struct i2c_driver imx219_i2c_driver = {
+ .driver = {
+ .name = "imx219",
+ .of_match_table = imx219_dt_ids,
+ .pm = &imx219_pm_ops,
+ },
+ .probe = imx219_probe,
+ .remove = imx219_remove,
+};
+
+module_i2c_driver(imx219_i2c_driver);
+
+MODULE_AUTHOR("Dave Stevenson <dave.stevenson@raspberrypi.com");
+MODULE_DESCRIPTION("Sony IMX219 sensor driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/2] Add IMX219 CMOS image sensor support
2020-01-10 20:09 [PATCH v3 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
2020-01-10 20:09 ` [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
2020-01-10 20:09 ` [PATCH v3 2/2] media: i2c: Add driver for Sony IMX219 sensor Andrey Konovalov
@ 2020-01-11 4:45 ` Ezequiel Garcia
2020-01-11 17:46 ` Andrey Konovalov
2 siblings, 1 reply; 6+ messages in thread
From: Ezequiel Garcia @ 2020-01-11 4:45 UTC (permalink / raw)
To: Andrey Konovalov, mchehab, robh+dt
Cc: linux-media, devicetree, peter.griffin, dave.stevenson, sakari.ailus
Hello Andrey,
Thanks for submitting a new version.
On Fri, 2020-01-10 at 23:09 +0300, Andrey Konovalov wrote:
> This patchset adds support for IMX219 CMOS image sensor from Sony.
> Sony IMX219 is an 8MPix, 1/4.0-inch CMOS active pixel digital image sensor
> with an active array size of 3280H x 2464V. It is programmable through
> I2C interface. Image data are sent through MIPI CSI-2, which can be configured
> as either 2 or 4 data lanes, but this driver currently only supports 2 lanes.
> The currently supported resolutions are 3280x2464 @ 15fps, 1920x1080 @ 30fps
> (cropped FOV), and 1640x1232 (2x2 binned) @ 30fps.
>
> The driver has been tested with Raspberry Pi Camera Module v2 connected to
> Raspberry Pi Zero W.
>
> Changes since v2 [1]:
>
> dt-bindings:
> - "clock-names" property removed
> - "xclr-gpios" property renamed to "reset-gpios"
> - the camera-clk mode moved out of sensor device node
> - "clock-lanes" property removed (the sensor doesn't support lane reordering)
> - "clock-noncontinuous" description made more clear (thanks Sakari)
> - "data-lanes" property reworked: it is now optional, and if it is not
> present the driver should assume four-lane operation. For two-lane
> operation (the only mode supported by the current driver) this property
> must be present and set to <1 2>
>
> imx219 sensor driver:
> - "xclr-gpios" property renamed to "reset-gpios", the corresponding
> struct gpio_desc field in the imx219 structure is renamed to reset_gpio
> - in the driver probe() a test to check that the number of CSI-2 data lanes
> is supported by the driver was added
> - devm_clk_get() is now called with NULL as the 2nd argument, as there is
> just single clock, and there is no need to use clock ID
> - error messages are added when the driver fails to get regulators, to init
> media entity pads, or to register sensor sub-device
>
It seems you missed Sakari's review comments on v2,
see https://patchwork.linuxtv.org/patch/60925/#114407
Thanks!
Eze
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/2] Add IMX219 CMOS image sensor support
2020-01-11 4:45 ` [PATCH v3 0/2] Add IMX219 CMOS image sensor support Ezequiel Garcia
@ 2020-01-11 17:46 ` Andrey Konovalov
0 siblings, 0 replies; 6+ messages in thread
From: Andrey Konovalov @ 2020-01-11 17:46 UTC (permalink / raw)
To: Ezequiel Garcia, mchehab, robh+dt
Cc: linux-media, devicetree, peter.griffin, dave.stevenson, sakari.ailus
Hi Ezequiel,
On 11.01.2020 07:45, Ezequiel Garcia wrote:
> Hello Andrey,
>
> Thanks for submitting a new version.
>
> On Fri, 2020-01-10 at 23:09 +0300, Andrey Konovalov wrote:
>> This patchset adds support for IMX219 CMOS image sensor from Sony.
>> Sony IMX219 is an 8MPix, 1/4.0-inch CMOS active pixel digital image sensor
>> with an active array size of 3280H x 2464V. It is programmable through
>> I2C interface. Image data are sent through MIPI CSI-2, which can be configured
>> as either 2 or 4 data lanes, but this driver currently only supports 2 lanes.
>> The currently supported resolutions are 3280x2464 @ 15fps, 1920x1080 @ 30fps
>> (cropped FOV), and 1640x1232 (2x2 binned) @ 30fps.
>>
>> The driver has been tested with Raspberry Pi Camera Module v2 connected to
>> Raspberry Pi Zero W.
>>
>> Changes since v2 [1]:
>>
>> dt-bindings:
>> - "clock-names" property removed
>> - "xclr-gpios" property renamed to "reset-gpios"
>> - the camera-clk mode moved out of sensor device node
>> - "clock-lanes" property removed (the sensor doesn't support lane reordering)
>> - "clock-noncontinuous" description made more clear (thanks Sakari)
>> - "data-lanes" property reworked: it is now optional, and if it is not
>> present the driver should assume four-lane operation. For two-lane
>> operation (the only mode supported by the current driver) this property
>> must be present and set to <1 2>
>>
>> imx219 sensor driver:
>> - "xclr-gpios" property renamed to "reset-gpios", the corresponding
>> struct gpio_desc field in the imx219 structure is renamed to reset_gpio
>> - in the driver probe() a test to check that the number of CSI-2 data lanes
>> is supported by the driver was added
>> - devm_clk_get() is now called with NULL as the 2nd argument, as there is
>> just single clock, and there is no need to use clock ID
>> - error messages are added when the driver fails to get regulators, to init
>> media entity pads, or to register sensor sub-device
>>
>
> It seems you missed Sakari's review comments on v2,
> see https://patchwork.linuxtv.org/patch/60925/#114407
Hm.. Indeed. I missed Sakari's comments on the imx219.c v2 somehow.
I'll post an updated patchset shortly.
Thanks!
Andrey
> Thanks!
> Eze
>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding
2020-01-10 20:09 ` [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
@ 2020-01-13 23:04 ` Rob Herring
0 siblings, 0 replies; 6+ messages in thread
From: Rob Herring @ 2020-01-13 23:04 UTC (permalink / raw)
To: Andrey Konovalov
Cc: mchehab, robh+dt, linux-media, devicetree, peter.griffin,
dave.stevenson, ezequiel, sakari.ailus, Andrey Konovalov
On Fri, 10 Jan 2020 23:09:14 +0300, Andrey Konovalov wrote:
> Add YAML device tree binding for IMX219 CMOS image sensor, and
> the relevant MAINTAINERS entries.
>
> Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
> ---
> .../devicetree/bindings/media/i2c/imx219.yaml | 104 ++++++++++++++++++
> MAINTAINERS | 8 ++
> 2 files changed, 112 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-01-13 23:04 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-10 20:09 [PATCH v3 0/2] Add IMX219 CMOS image sensor support Andrey Konovalov
2020-01-10 20:09 ` [PATCH v3 1/2] dt-bindings: media: i2c: Add IMX219 CMOS sensor binding Andrey Konovalov
2020-01-13 23:04 ` Rob Herring
2020-01-10 20:09 ` [PATCH v3 2/2] media: i2c: Add driver for Sony IMX219 sensor Andrey Konovalov
2020-01-11 4:45 ` [PATCH v3 0/2] Add IMX219 CMOS image sensor support Ezequiel Garcia
2020-01-11 17:46 ` Andrey Konovalov
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).