[PATCH AUTOSEL 4.19 04/35] media: ite-cir: check for receive overflow

[PATCH AUTOSEL 4.19 04/35] media: ite-cir: check for receive overflow

[Sasha Levin]

From: Sean Young <sean@mess.org>

[ Upstream commit 28c7afb07ccfc0a939bb06ac1e7afe669901c65a ]

It's best if this condition is reported.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/rc/ite-cir.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/media/rc/ite-cir.c b/drivers/media/rc/ite-cir.c
index de77d22c30a7..18f3718315a8 100644
--- a/drivers/media/rc/ite-cir.c
+++ b/drivers/media/rc/ite-cir.c
@@ -285,8 +285,14 @@ static irqreturn_t ite_cir_isr(int irq, void *data)
 	/* read the interrupt flags */
 	iflags = dev->params.get_irq_causes(dev);
 
+	/* Check for RX overflow */
+	if (iflags & ITE_IRQ_RX_FIFO_OVERRUN) {
+		dev_warn(&dev->rdev->dev, "receive overflow\n");
+		ir_raw_event_reset(dev->rdev);
+	}
+
 	/* check for the receive interrupt */
-	if (iflags & (ITE_IRQ_RX_FIFO | ITE_IRQ_RX_FIFO_OVERRUN)) {
+	if (iflags & ITE_IRQ_RX_FIFO) {
 		/* read the FIFO bytes */
 		rx_bytes =
 			dev->params.get_rx_bytes(dev, rx_buf,
-- 
2.30.2

[PATCH AUTOSEL 4.19 05/35] media: drivers: media: pci: sta2x11: fix Kconfig dependency on GPIOLIB

[Sasha Levin]

From: Julian Braha <julianbraha@gmail.com>

[ Upstream commit 24df8b74c8b2fb42c49ffe8585562da0c96446ff ]

When STA2X11_VIP is enabled, and GPIOLIB is disabled,
Kbuild gives the following warning:

WARNING: unmet direct dependencies detected for VIDEO_ADV7180
  Depends on [n]: MEDIA_SUPPORT [=y] && GPIOLIB [=n] && VIDEO_V4L2 [=y] && I2C [=y]
  Selected by [y]:
  - STA2X11_VIP [=y] && MEDIA_SUPPORT [=y] && MEDIA_PCI_SUPPORT [=y] && MEDIA_CAMERA_SUPPORT [=y] && PCI [=y] && VIDEO_V4L2 [=y] && VIRT_TO_BUS [=y] && I2C [=y] && (STA2X11 [=n] || COMPILE_TEST [=y]) && MEDIA_SUBDRV_AUTOSELECT [=y]

This is because STA2X11_VIP selects VIDEO_ADV7180
without selecting or depending on GPIOLIB,
despite VIDEO_ADV7180 depending on GPIOLIB.

Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/sta2x11/Kconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/pci/sta2x11/Kconfig b/drivers/media/pci/sta2x11/Kconfig
index 4407b9f881e4..bd690613fe68 100644
--- a/drivers/media/pci/sta2x11/Kconfig
+++ b/drivers/media/pci/sta2x11/Kconfig
@@ -1,6 +1,7 @@
 config STA2X11_VIP
 	tristate "STA2X11 VIP Video For Linux"
 	depends on STA2X11 || COMPILE_TEST
+	select GPIOLIB if MEDIA_SUBDRV_AUTOSELECT
 	select VIDEO_ADV7180 if MEDIA_SUBDRV_AUTOSELECT
 	select VIDEOBUF2_DMA_CONTIG
 	depends on PCI && VIDEO_V4L2 && VIRT_TO_BUS
-- 
2.30.2

[PATCH AUTOSEL 4.19 08/35] media: media/saa7164: fix saa7164_encoder_register() memory leak bugs

[Sasha Levin]

From: Daniel Niv <danielniv3@gmail.com>

[ Upstream commit c759b2970c561e3b56aa030deb13db104262adfe ]

Add a fix for the memory leak bugs that can occur when the
saa7164_encoder_register() function fails.
The function allocates memory without explicitly freeing
it when errors occur.
Add a better error handling that deallocate the unused buffers before the
function exits during a fail.

Signed-off-by: Daniel Niv <danielniv3@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/saa7164/saa7164-encoder.c | 20 +++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)

diff --git a/drivers/media/pci/saa7164/saa7164-encoder.c b/drivers/media/pci/saa7164/saa7164-encoder.c
index 32136ebe4f61..962f8eb73b05 100644
--- a/drivers/media/pci/saa7164/saa7164-encoder.c
+++ b/drivers/media/pci/saa7164/saa7164-encoder.c
@@ -1024,7 +1024,7 @@ int saa7164_encoder_register(struct saa7164_port *port)
 		printk(KERN_ERR "%s() failed (errno = %d), NO PCI configuration\n",
 			__func__, result);
 		result = -ENOMEM;
-		goto failed;
+		goto fail_pci;
 	}
 
 	/* Establish encoder defaults here */
@@ -1078,7 +1078,7 @@ int saa7164_encoder_register(struct saa7164_port *port)
 			  100000, ENCODER_DEF_BITRATE);
 	if (hdl->error) {
 		result = hdl->error;
-		goto failed;
+		goto fail_hdl;
 	}
 
 	port->std = V4L2_STD_NTSC_M;
@@ -1096,7 +1096,7 @@ int saa7164_encoder_register(struct saa7164_port *port)
 		printk(KERN_INFO "%s: can't allocate mpeg device\n",
 			dev->name);
 		result = -ENOMEM;
-		goto failed;
+		goto fail_hdl;
 	}
 
 	port->v4l_device->ctrl_handler = hdl;
@@ -1107,10 +1107,7 @@ int saa7164_encoder_register(struct saa7164_port *port)
 	if (result < 0) {
 		printk(KERN_INFO "%s: can't register mpeg device\n",
 			dev->name);
-		/* TODO: We're going to leak here if we don't dealloc
-		 The buffers above. The unreg function can't deal wit it.
-		*/
-		goto failed;
+		goto fail_reg;
 	}
 
 	printk(KERN_INFO "%s: registered device video%d [mpeg]\n",
@@ -1132,9 +1129,14 @@ int saa7164_encoder_register(struct saa7164_port *port)
 
 	saa7164_api_set_encoder(port);
 	saa7164_api_get_encoder(port);
+	return 0;
 
-	result = 0;
-failed:
+fail_reg:
+	video_device_release(port->v4l_device);
+	port->v4l_device = NULL;
+fail_hdl:
+	v4l2_ctrl_handler_free(hdl);
+fail_pci:
 	return result;
 }
 
-- 
2.30.2

[PATCH AUTOSEL 4.19 09/35] media: gspca/sq905.c: fix uninitialized variable

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit eaaea4681984c79d2b2b160387b297477f0c1aab ]

act_len can be uninitialized if usb_bulk_msg() returns an error.
Set it to 0 to avoid a KMSAN error.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+a4e309017a5f3a24c7b3@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/gspca/sq905.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/usb/gspca/sq905.c b/drivers/media/usb/gspca/sq905.c
index ffea9c35b0a0..13676af42cfc 100644
--- a/drivers/media/usb/gspca/sq905.c
+++ b/drivers/media/usb/gspca/sq905.c
@@ -167,7 +167,7 @@ static int
 sq905_read_data(struct gspca_dev *gspca_dev, u8 *data, int size, int need_lock)
 {
 	int ret;
-	int act_len;
+	int act_len = 0;
 
 	gspca_dev->usb_buf[0] = '\0';
 	if (need_lock)
-- 
2.30.2

[PATCH AUTOSEL 4.19 10/35] media: pci: saa7164: Rudimentary spelling fixes in the file saa7164-types.h

[Sasha Levin]

From: Bhaskar Chowdhury <unixbhaskar@gmail.com>

[ Upstream commit 4b19f9716ad89af51f07f9b611aabfd5fd80c625 ]

s/structues/structures/
s/decies/decides/

Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/pci/saa7164/saa7164-types.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/media/pci/saa7164/saa7164-types.h b/drivers/media/pci/saa7164/saa7164-types.h
index ae241103b261..6572bc313f96 100644
--- a/drivers/media/pci/saa7164/saa7164-types.h
+++ b/drivers/media/pci/saa7164/saa7164-types.h
@@ -17,7 +17,7 @@
 
 /* TODO: Cleanup and shorten the namespace */
 
-/* Some structues are passed directly to/from the firmware and
+/* Some structures are passed directly to/from the firmware and
  * have strict alignment requirements. This is one of them.
  */
 struct tmComResHWDescr {
@@ -38,7 +38,7 @@ struct tmComResHWDescr {
 /* This is DWORD aligned on windows but I can't find the right
  * gcc syntax to match the binary data from the device.
  * I've manually padded with Reserved[3] bytes to match the hardware,
- * but this could break if GCC decies to pack in a different way.
+ * but this could break if GCC decides to pack in a different way.
  */
 struct tmComResInterfaceDescr {
 	u8	bLength;
-- 
2.30.2

[PATCH AUTOSEL 4.19 18/35] media: em28xx: fix memory leak

[Sasha Levin]

From: Muhammad Usama Anjum <musamaanjum@gmail.com>

[ Upstream commit 0ae10a7dc8992ee682ff0b1752ff7c83d472eef1 ]

If some error occurs, URB buffers should also be freed. If they aren't
freed with the dvb here, the em28xx_dvb_fini call doesn't frees the URB
buffers as dvb is set to NULL. The function in which error occurs should
do all the cleanup for the allocations it had done.

Tested the patch with the reproducer provided by syzbot. This patch
fixes the memleak.

Reported-by: syzbot+889397c820fa56adf25d@syzkaller.appspotmail.com
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/em28xx/em28xx-dvb.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/usb/em28xx/em28xx-dvb.c b/drivers/media/usb/em28xx/em28xx-dvb.c
index a73faf12f7e4..e1946237ac8c 100644
--- a/drivers/media/usb/em28xx/em28xx-dvb.c
+++ b/drivers/media/usb/em28xx/em28xx-dvb.c
@@ -1924,6 +1924,7 @@ static int em28xx_dvb_init(struct em28xx *dev)
 	return result;
 
 out_free:
+	em28xx_uninit_usb_xfer(dev, EM28XX_DIGITAL_MODE);
 	kfree(dvb);
 	dev->dvb = NULL;
 	goto ret;
-- 
2.30.2

[PATCH AUTOSEL 4.19 19/35] media: vivid: update EDID

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit 443ec4bbc6116f6f492a7a1282bfd8422c862158 ]

The EDID had a few mistakes as reported by edid-decode:

Block 1, CTA-861 Extension Block:
  Video Data Block: For improved preferred timing interoperability, set 'Native detailed modes' to 1.
  Video Capability Data Block: S_PT is equal to S_IT and S_CE, so should be set to 0 instead.

Fixed those.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/vivid/vivid-core.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/media/platform/vivid/vivid-core.c b/drivers/media/platform/vivid/vivid-core.c
index 31db363602e5..b603ca412387 100644
--- a/drivers/media/platform/vivid/vivid-core.c
+++ b/drivers/media/platform/vivid/vivid-core.c
@@ -174,13 +174,13 @@ static const u8 vivid_hdmi_edid[256] = {
 	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
 	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x7b,
 
-	0x02, 0x03, 0x3f, 0xf0, 0x51, 0x61, 0x60, 0x5f,
+	0x02, 0x03, 0x3f, 0xf1, 0x51, 0x61, 0x60, 0x5f,
 	0x5e, 0x5d, 0x10, 0x1f, 0x04, 0x13, 0x22, 0x21,
 	0x20, 0x05, 0x14, 0x02, 0x11, 0x01, 0x23, 0x09,
 	0x07, 0x07, 0x83, 0x01, 0x00, 0x00, 0x6d, 0x03,
 	0x0c, 0x00, 0x10, 0x00, 0x00, 0x3c, 0x21, 0x00,
 	0x60, 0x01, 0x02, 0x03, 0x67, 0xd8, 0x5d, 0xc4,
-	0x01, 0x78, 0x00, 0x00, 0xe2, 0x00, 0xea, 0xe3,
+	0x01, 0x78, 0x00, 0x00, 0xe2, 0x00, 0xca, 0xe3,
 	0x05, 0x00, 0x00, 0xe3, 0x06, 0x01, 0x00, 0x4d,
 	0xd0, 0x00, 0xa0, 0xf0, 0x70, 0x3e, 0x80, 0x30,
 	0x20, 0x35, 0x00, 0xc0, 0x1c, 0x32, 0x00, 0x00,
@@ -189,7 +189,7 @@ static const u8 vivid_hdmi_edid[256] = {
 	0x00, 0x00, 0x1a, 0x1a, 0x1d, 0x00, 0x80, 0x51,
 	0xd0, 0x1c, 0x20, 0x40, 0x80, 0x35, 0x00, 0xc0,
 	0x1c, 0x32, 0x00, 0x00, 0x1c, 0x00, 0x00, 0x00,
-	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x63,
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x82,
 };
 
 static int vidioc_querycap(struct file *file, void  *priv,
-- 
2.30.2

[PATCH AUTOSEL 4.19 23/35] media: tc358743: fix possible use-after-free in tc358743_remove()

[Sasha Levin]

From: Yang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 6107a4fdf8554a7aa9488bdc835bb010062fa8a9 ]

This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.

Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/tc358743.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/i2c/tc358743.c b/drivers/media/i2c/tc358743.c
index d9bc3851bf63..041b16965b96 100644
--- a/drivers/media/i2c/tc358743.c
+++ b/drivers/media/i2c/tc358743.c
@@ -2192,7 +2192,7 @@ static int tc358743_remove(struct i2c_client *client)
 		del_timer_sync(&state->timer);
 		flush_work(&state->work_i2c_poll);
 	}
-	cancel_delayed_work(&state->delayed_work_enable_hotplug);
+	cancel_delayed_work_sync(&state->delayed_work_enable_hotplug);
 	cec_unregister_adapter(state->cec_adap);
 	v4l2_async_unregister_subdev(sd);
 	v4l2_device_unregister_subdev(sd);
-- 
2.30.2

[PATCH AUTOSEL 4.19 24/35] media: adv7604: fix possible use-after-free in adv76xx_remove()

[Sasha Levin]

From: Yang Yingliang <yangyingliang@huawei.com>

[ Upstream commit fa56f5f1fe31c2050675fa63b84963ebd504a5b3 ]

This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.

Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/adv7604.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
index a4b0a89c7e7e..04577d409e63 100644
--- a/drivers/media/i2c/adv7604.c
+++ b/drivers/media/i2c/adv7604.c
@@ -3560,7 +3560,7 @@ static int adv76xx_remove(struct i2c_client *client)
 	io_write(sd, 0x6e, 0);
 	io_write(sd, 0x73, 0);
 
-	cancel_delayed_work(&state->delayed_work_enable_hotplug);
+	cancel_delayed_work_sync(&state->delayed_work_enable_hotplug);
 	v4l2_async_unregister_subdev(sd);
 	media_entity_cleanup(&sd->entity);
 	adv76xx_unregister_clients(to_state(sd));
-- 
2.30.2

[PATCH AUTOSEL 4.19 25/35] media: i2c: adv7511-v4l2: fix possible use-after-free in adv7511_remove()

[Sasha Levin]

From: Yang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 2c9541720c66899adf6f3600984cf3ef151295ad ]

This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.

Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/adv7511-v4l2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/i2c/adv7511-v4l2.c b/drivers/media/i2c/adv7511-v4l2.c
index 6869bb593a68..4052abeead50 100644
--- a/drivers/media/i2c/adv7511-v4l2.c
+++ b/drivers/media/i2c/adv7511-v4l2.c
@@ -1965,7 +1965,7 @@ static int adv7511_remove(struct i2c_client *client)
 
 	adv7511_set_isr(sd, false);
 	adv7511_init_setup(sd);
-	cancel_delayed_work(&state->edid_handler);
+	cancel_delayed_work_sync(&state->edid_handler);
 	i2c_unregister_device(state->i2c_edid);
 	if (state->i2c_cec)
 		i2c_unregister_device(state->i2c_cec);
-- 
2.30.2

[PATCH AUTOSEL 4.19 26/35] media: i2c: adv7842: fix possible use-after-free in adv7842_remove()

[Sasha Levin]

From: Yang Yingliang <yangyingliang@huawei.com>

[ Upstream commit 4a15275b6a18597079f18241c87511406575179a ]

This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.

Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/adv7842.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/i2c/adv7842.c b/drivers/media/i2c/adv7842.c
index 58662ba92d4f..d0ed20652ddb 100644
--- a/drivers/media/i2c/adv7842.c
+++ b/drivers/media/i2c/adv7842.c
@@ -3585,7 +3585,7 @@ static int adv7842_remove(struct i2c_client *client)
 	struct adv7842_state *state = to_state(sd);
 
 	adv7842_irq_enable(sd, false);
-	cancel_delayed_work(&state->delayed_work_enable_hotplug);
+	cancel_delayed_work_sync(&state->delayed_work_enable_hotplug);
 	v4l2_device_unregister_subdev(sd);
 	media_entity_cleanup(&sd->entity);
 	adv7842_unregister_clients(sd);
-- 
2.30.2

[PATCH AUTOSEL 4.19 27/35] media: dvb-usb: fix memory leak in dvb_usb_adapter_init

[Sasha Levin]

From: Pavel Skripkin <paskripkin@gmail.com>

[ Upstream commit b7cd0da982e3043f2eec7235ac5530cb18d6af1d ]

syzbot reported memory leak in dvb-usb. The problem was
in invalid error handling in dvb_usb_adapter_init().

for (n = 0; n < d->props.num_adapters; n++) {
....
	if ((ret = dvb_usb_adapter_stream_init(adap)) ||
		(ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs)) ||
		(ret = dvb_usb_adapter_frontend_init(adap))) {
		return ret;
	}
...
	d->num_adapters_initialized++;
...
}

In case of error in dvb_usb_adapter_dvb_init() or
dvb_usb_adapter_dvb_init() d->num_adapters_initialized won't be
incremented, but dvb_usb_adapter_exit() relies on it:

	for (n = 0; n < d->num_adapters_initialized; n++)

So, allocated objects won't be freed.

Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reported-by: syzbot+3c2be7424cea3b932b0e@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/dvb-usb/dvb-usb-init.c | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

diff --git a/drivers/media/usb/dvb-usb/dvb-usb-init.c b/drivers/media/usb/dvb-usb/dvb-usb-init.c
index 39ac22486bcd..4b1445d806e5 100644
--- a/drivers/media/usb/dvb-usb/dvb-usb-init.c
+++ b/drivers/media/usb/dvb-usb/dvb-usb-init.c
@@ -82,11 +82,17 @@ static int dvb_usb_adapter_init(struct dvb_usb_device *d, short *adapter_nrs)
 			}
 		}
 
-		if ((ret = dvb_usb_adapter_stream_init(adap)) ||
-			(ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs)) ||
-			(ret = dvb_usb_adapter_frontend_init(adap))) {
+		ret = dvb_usb_adapter_stream_init(adap);
+		if (ret)
 			return ret;
-		}
+
+		ret = dvb_usb_adapter_dvb_init(adap, adapter_nrs);
+		if (ret)
+			goto dvb_init_err;
+
+		ret = dvb_usb_adapter_frontend_init(adap);
+		if (ret)
+			goto frontend_init_err;
 
 		/* use exclusive FE lock if there is multiple shared FEs */
 		if (adap->fe_adap[1].fe)
@@ -106,6 +112,12 @@ static int dvb_usb_adapter_init(struct dvb_usb_device *d, short *adapter_nrs)
 	}
 
 	return 0;
+
+frontend_init_err:
+	dvb_usb_adapter_dvb_exit(adap);
+dvb_init_err:
+	dvb_usb_adapter_stream_exit(adap);
+	return ret;
 }
 
 static int dvb_usb_adapter_exit(struct dvb_usb_device *d)
-- 
2.30.2

[PATCH AUTOSEL 4.19 28/35] media: gscpa/stv06xx: fix memory leak

[Sasha Levin]

From: Hans Verkuil <hverkuil-cisco@xs4all.nl>

[ Upstream commit 4f4e6644cd876c844cdb3bea2dd7051787d5ae25 ]

For two of the supported sensors the stv06xx driver allocates memory which
is stored in sd->sensor_priv. This memory is freed on a disconnect, but if
the probe() fails, then it isn't freed and so this leaks memory.

Add a new probe_error() op that drivers can use to free any allocated
memory in case there was a probe failure.

Thanks to Pavel Skripkin <paskripkin@gmail.com> for discovering the cause
of the memory leak.

Reported-and-tested-by: syzbot+e7f4c64a4248a0340c37@syzkaller.appspotmail.com

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/gspca/gspca.c           | 2 ++
 drivers/media/usb/gspca/gspca.h           | 1 +
 drivers/media/usb/gspca/stv06xx/stv06xx.c | 9 +++++++++
 3 files changed, 12 insertions(+)

diff --git a/drivers/media/usb/gspca/gspca.c b/drivers/media/usb/gspca/gspca.c
index 93212ed80bf8..f0562b8eef56 100644
--- a/drivers/media/usb/gspca/gspca.c
+++ b/drivers/media/usb/gspca/gspca.c
@@ -1586,6 +1586,8 @@ int gspca_dev_probe2(struct usb_interface *intf,
 #endif
 	v4l2_ctrl_handler_free(gspca_dev->vdev.ctrl_handler);
 	v4l2_device_unregister(&gspca_dev->v4l2_dev);
+	if (sd_desc->probe_error)
+		sd_desc->probe_error(gspca_dev);
 	kfree(gspca_dev->usb_buf);
 	kfree(gspca_dev);
 	return ret;
diff --git a/drivers/media/usb/gspca/gspca.h b/drivers/media/usb/gspca/gspca.h
index b0ced2e14006..a6554d5e9e1a 100644
--- a/drivers/media/usb/gspca/gspca.h
+++ b/drivers/media/usb/gspca/gspca.h
@@ -105,6 +105,7 @@ struct sd_desc {
 	cam_cf_op config;	/* called on probe */
 	cam_op init;		/* called on probe and resume */
 	cam_op init_controls;	/* called on probe */
+	cam_v_op probe_error;	/* called if probe failed, do cleanup here */
 	cam_op start;		/* called on stream on after URBs creation */
 	cam_pkt_op pkt_scan;
 /* optional operations */
diff --git a/drivers/media/usb/gspca/stv06xx/stv06xx.c b/drivers/media/usb/gspca/stv06xx/stv06xx.c
index b7ea4f982964..ccec6138f678 100644
--- a/drivers/media/usb/gspca/stv06xx/stv06xx.c
+++ b/drivers/media/usb/gspca/stv06xx/stv06xx.c
@@ -538,12 +538,21 @@ static int sd_int_pkt_scan(struct gspca_dev *gspca_dev,
 static int stv06xx_config(struct gspca_dev *gspca_dev,
 			  const struct usb_device_id *id);
 
+static void stv06xx_probe_error(struct gspca_dev *gspca_dev)
+{
+	struct sd *sd = (struct sd *)gspca_dev;
+
+	kfree(sd->sensor_priv);
+	sd->sensor_priv = NULL;
+}
+
 /* sub-driver description */
 static const struct sd_desc sd_desc = {
 	.name = MODULE_NAME,
 	.config = stv06xx_config,
 	.init = stv06xx_init,
 	.init_controls = stv06xx_init_controls,
+	.probe_error = stv06xx_probe_error,
 	.start = stv06xx_start,
 	.stopN = stv06xx_stopN,
 	.pkt_scan = stv06xx_pkt_scan,
-- 
2.30.2