[PATCH v6 5/8] arm64: dts: renesas: condor: Enable MAX9286

[Jacopo Mondi <jacopo+renesas@jmondi.org>]

Enable the MAX9286 GMSL deserializers on Condor-V3H board.

Connected cameras should be defined in a device-tree overlay or included
after these definitions.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
 .../boot/dts/renesas/r8a77980-condor.dts      | 193 ++++++++++++++++++
 1 file changed, 193 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
index 04d47c0c9bb9..cb79c8738b78 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -6,6 +6,8 @@
  * Copyright (C) 2018 Cogent Embedded, Inc.
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 /dts-v1/;
 #include "r8a77980.dtsi"
 
@@ -107,6 +109,34 @@ channel0 {
 	};
 };
 
+&csi40 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max9286_out0>;
+			};
+		};
+	};
+};
+
+&csi41 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi41_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max9286_out1>;
+			};
+		};
+	};
+};
+
 &du {
 	clocks = <&cpg CPG_MOD 724>,
 		 <&x1_clk>;
@@ -196,6 +226,164 @@ adv7511_out: endpoint {
 	};
 };
 
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	gmsl0: gmsl-deserializer@48 {
+		compatible = "maxim,max9286";
+		reg = <0x48>;
+
+		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&io_expander0 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				max9286_out0: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+
+		i2c-mux {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				status = "disabled";
+			};
+
+			i2c@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				status = "disabled";
+			};
+
+			i2c@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				status = "disabled";
+			};
+
+			i2c@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				status = "disabled";
+			};
+		};
+	};
+
+	gmsl1: gmsl-deserializer@4a {
+		compatible = "maxim,max9286";
+		reg = <0x4a>;
+
+		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&io_expander1 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				max9286_out1: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi41_in>;
+				};
+			};
+		};
+
+		i2c-mux {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				status = "disabled";
+			};
+
+			i2c@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				status = "disabled";
+			};
+
+			i2c@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				status = "disabled";
+			};
+
+			i2c@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				status = "disabled";
+			};
+		};
+	};
+};
+
 &lvds0 {
 	status = "okay";
 
@@ -252,6 +440,11 @@ i2c0_pins: i2c0 {
 		function = "i2c0";
 	};
 
+	i2c1_pins: i2c1 {
+		groups = "i2c1";
+		function = "i2c1";
+	};
+
 	mmc_pins: mmc {
 		groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
 		function = "mmc";
-- 
2.32.0