[PATCH AUTOSEL 4.4 09/30] media: mt9p031: Fix corrupted frame after restarting stream

[PATCH AUTOSEL 4.4 09/30] media: mt9p031: Fix corrupted frame after restarting stream

[Sasha Levin]

From: Dirk Bender <d.bender@phytec.de>

[ Upstream commit 0961ba6dd211a4a52d1dd4c2d59be60ac2dc08c7 ]

To prevent corrupted frames after starting and stopping the sensor its
datasheet specifies a specific pause sequence to follow:

Stopping:
	Set Pause_Restart Bit -> Set Restart Bit -> Set Chip_Enable Off

Restarting:
	Set Chip_Enable On -> Clear Pause_Restart Bit

The Restart Bit is cleared automatically and must not be cleared
manually as this would cause undefined behavior.

Signed-off-by: Dirk Bender <d.bender@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/i2c/mt9p031.c | 28 +++++++++++++++++++++++++++-
 1 file changed, 27 insertions(+), 1 deletion(-)

diff --git a/drivers/media/i2c/mt9p031.c b/drivers/media/i2c/mt9p031.c
index 0db15f528ac1c..fb60c9f42cb60 100644
--- a/drivers/media/i2c/mt9p031.c
+++ b/drivers/media/i2c/mt9p031.c
@@ -81,7 +81,9 @@
 #define		MT9P031_PIXEL_CLOCK_INVERT		(1 << 15)
 #define		MT9P031_PIXEL_CLOCK_SHIFT(n)		((n) << 8)
 #define		MT9P031_PIXEL_CLOCK_DIVIDE(n)		((n) << 0)
-#define MT9P031_FRAME_RESTART				0x0b
+#define MT9P031_RESTART					0x0b
+#define		MT9P031_FRAME_PAUSE_RESTART		(1 << 1)
+#define		MT9P031_FRAME_RESTART			(1 << 0)
 #define MT9P031_SHUTTER_DELAY				0x0c
 #define MT9P031_RST					0x0d
 #define		MT9P031_RST_ENABLE			1
@@ -448,9 +450,23 @@ static int mt9p031_set_params(struct mt9p031 *mt9p031)
 static int mt9p031_s_stream(struct v4l2_subdev *subdev, int enable)
 {
 	struct mt9p031 *mt9p031 = to_mt9p031(subdev);
+	struct i2c_client *client = v4l2_get_subdevdata(subdev);
+	int val;
 	int ret;
 
 	if (!enable) {
+		/* enable pause restart */
+		val = MT9P031_FRAME_PAUSE_RESTART;
+		ret = mt9p031_write(client, MT9P031_RESTART, val);
+		if (ret < 0)
+			return ret;
+
+		/* enable restart + keep pause restart set */
+		val |= MT9P031_FRAME_RESTART;
+		ret = mt9p031_write(client, MT9P031_RESTART, val);
+		if (ret < 0)
+			return ret;
+
 		/* Stop sensor readout */
 		ret = mt9p031_set_output_control(mt9p031,
 						 MT9P031_OUTPUT_CONTROL_CEN, 0);
@@ -470,6 +486,16 @@ static int mt9p031_s_stream(struct v4l2_subdev *subdev, int enable)
 	if (ret < 0)
 		return ret;
 
+	/*
+	 * - clear pause restart
+	 * - don't clear restart as clearing restart manually can cause
+	 *   undefined behavior
+	 */
+	val = MT9P031_FRAME_RESTART;
+	ret = mt9p031_write(client, MT9P031_RESTART, val);
+	if (ret < 0)
+		return ret;
+
 	return mt9p031_pll_enable(mt9p031);
 }
 
-- 
2.33.0

[PATCH AUTOSEL 4.4 10/30] media: netup_unidvb: handle interrupt properly according to the firmware

[Sasha Levin]

From: Zheyu Ma <zheyuma97@gmail.com>

[ Upstream commit dbb4cfea6efe979ed153bd59a6a527a90d3d0ab3 ]

The interrupt handling should be related to the firmware version. If
the driver matches an old firmware, then the driver should not handle
interrupt such as i2c or dma, otherwise it will cause some errors.

This log reveals it:

[   27.708641] INFO: trying to register non-static key.
[   27.710851] The code is fine but needs lockdep annotation, or maybe
[   27.712010] you didn't initialize this object before use?
[   27.712396] turning off the locking correctness validator.
[   27.712787] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169
[   27.713349] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   27.714149] Call Trace:
[   27.714329]  <IRQ>
[   27.714480]  dump_stack+0xba/0xf5
[   27.714737]  register_lock_class+0x873/0x8f0
[   27.715052]  ? __lock_acquire+0x323/0x1930
[   27.715353]  __lock_acquire+0x75/0x1930
[   27.715636]  lock_acquire+0x1dd/0x3e0
[   27.715905]  ? netup_i2c_interrupt+0x19/0x310
[   27.716226]  _raw_spin_lock_irqsave+0x4b/0x60
[   27.716544]  ? netup_i2c_interrupt+0x19/0x310
[   27.716863]  netup_i2c_interrupt+0x19/0x310
[   27.717178]  netup_unidvb_isr+0xd3/0x160
[   27.717467]  __handle_irq_event_percpu+0x53/0x3e0
[   27.717808]  handle_irq_event_percpu+0x35/0x90
[   27.718129]  handle_irq_event+0x39/0x60
[   27.718409]  handle_fasteoi_irq+0xc2/0x1d0
[   27.718707]  __common_interrupt+0x7f/0x150
[   27.719008]  common_interrupt+0xb4/0xd0
[   27.719289]  </IRQ>
[   27.719446]  asm_common_interrupt+0x1e/0x40
[   27.719747] RIP: 0010:native_safe_halt+0x17/0x20
[   27.720084] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6
[   27.721386] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   27.721758] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[   27.722262] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6
[   27.722770] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001
[   27.723277] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408
[   27.723781] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000
[   27.724289]  default_idle+0x9/0x10
[   27.724537]  arch_cpu_idle+0xa/0x10
[   27.724791]  default_idle_call+0x6e/0x250
[   27.725082]  do_idle+0x1f0/0x2d0
[   27.725326]  cpu_startup_entry+0x18/0x20
[   27.725613]  start_secondary+0x11f/0x160
[   27.725902]  secondary_startup_64_no_verify+0xb0/0xbb
[   27.726272] BUG: kernel NULL pointer dereference, address: 0000000000000002
[   27.726768] #PF: supervisor read access in kernel mode
[   27.727138] #PF: error_code(0x0000) - not-present page
[   27.727507] PGD 8000000118688067 P4D 8000000118688067 PUD 10feab067 PMD 0
[   27.727999] Oops: 0000 [#1] PREEMPT SMP PTI
[   27.728302] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 5.12.4-g70e7f0549188-dirty #169
[   27.728861] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[   27.729660] RIP: 0010:netup_i2c_interrupt+0x23/0x310
[   27.730019] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02
[   27.731339] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046
[   27.731716] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000
[   27.732223] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8
[   27.732727] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001
[   27.733239] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000
[   27.733745] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400
[   27.734251] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000
[   27.734821] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   27.735228] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0
[   27.735735] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   27.736241] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   27.736744] Call Trace:
[   27.736924]  <IRQ>
[   27.737074]  netup_unidvb_isr+0xd3/0x160
[   27.737363]  __handle_irq_event_percpu+0x53/0x3e0
[   27.737706]  handle_irq_event_percpu+0x35/0x90
[   27.738028]  handle_irq_event+0x39/0x60
[   27.738306]  handle_fasteoi_irq+0xc2/0x1d0
[   27.738602]  __common_interrupt+0x7f/0x150
[   27.738899]  common_interrupt+0xb4/0xd0
[   27.739176]  </IRQ>
[   27.739331]  asm_common_interrupt+0x1e/0x40
[   27.739633] RIP: 0010:native_safe_halt+0x17/0x20
[   27.739967] Code: 07 0f 00 2d 8b ee 4c 00 f4 5d c3 0f 1f 84 00 00 00 00 00 8b 05 72 95 17 02 55 48 89 e5 85 c0 7e 07 0f 00 2d 6b ee 4c 00 fb f4 <5d> c3 cc cc cc cc cc cc cc 55 48 89 e5 e8 67 53 ff ff 8b 0d 29 f6
[   27.741275] RSP: 0018:ffffc9000008fe90 EFLAGS: 00000246
[   27.741647] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[   27.742148] RDX: 0000000000000000 RSI: ffffffff85f7c054 RDI: ffffffff85ded4e6
[   27.742652] RBP: ffffc9000008fe90 R08: 0000000000000001 R09: 0000000000000001
[   27.743154] R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86a75408
[   27.743652] R13: 0000000000000000 R14: 0000000000000000 R15: ffff888100260000
[   27.744157]  default_idle+0x9/0x10
[   27.744405]  arch_cpu_idle+0xa/0x10
[   27.744658]  default_idle_call+0x6e/0x250
[   27.744948]  do_idle+0x1f0/0x2d0
[   27.745190]  cpu_startup_entry+0x18/0x20
[   27.745475]  start_secondary+0x11f/0x160
[   27.745761]  secondary_startup_64_no_verify+0xb0/0xbb
[   27.746123] Modules linked in:
[   27.746348] Dumping ftrace buffer:
[   27.746596]    (ftrace buffer empty)
[   27.746852] CR2: 0000000000000002
[   27.747094] ---[ end trace ebafd46f83ab946d ]---
[   27.747424] RIP: 0010:netup_i2c_interrupt+0x23/0x310
[   27.747778] Code: 0f 1f 80 00 00 00 00 55 48 89 e5 41 55 41 54 53 48 89 fb e8 af 6e 95 fd 48 89 df e8 e7 9f 1c 01 49 89 c5 48 8b 83 48 08 00 00 <66> 44 8b 60 02 44 89 e0 48 8b 93 48 08 00 00 83 e0 f8 66 89 42 02
[   27.749082] RSP: 0018:ffffc90000118e90 EFLAGS: 00010046
[   27.749461] RAX: 0000000000000000 RBX: ffff88810803c4d8 RCX: 0000000000000000
[   27.749966] RDX: 0000000000000001 RSI: ffffffff85d37b94 RDI: ffff88810803c4d8
[   27.750471] RBP: ffffc90000118ea8 R08: 0000000000000000 R09: 0000000000000001
[   27.750976] R10: ffff88810803c4f0 R11: 61646e6f63657320 R12: 0000000000000000
[   27.751480] R13: 0000000000000046 R14: ffff888101041000 R15: ffff8881081b2400
[   27.751986] FS:  0000000000000000(0000) GS:ffff88817bc80000(0000) knlGS:0000000000000000
[   27.752560] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   27.752970] CR2: 0000000000000002 CR3: 0000000108194000 CR4: 00000000000006e0
[   27.753481] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   27.753984] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   27.754487] Kernel panic - not syncing: Fatal exception in interrupt
[   27.755033] Dumping ftrace buffer:
[   27.755279]    (ftrace buffer empty)
[   27.755534] Kernel Offset: disabled
[   27.755785] Rebooting in 1 seconds..

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../pci/netup_unidvb/netup_unidvb_core.c      | 27 +++++++++++--------
 1 file changed, 16 insertions(+), 11 deletions(-)

diff --git a/drivers/media/pci/netup_unidvb/netup_unidvb_core.c b/drivers/media/pci/netup_unidvb/netup_unidvb_core.c
index 3fdbd81b55806..a83ba068b8376 100644
--- a/drivers/media/pci/netup_unidvb/netup_unidvb_core.c
+++ b/drivers/media/pci/netup_unidvb/netup_unidvb_core.c
@@ -253,19 +253,24 @@ static irqreturn_t netup_unidvb_isr(int irq, void *dev_id)
 	if ((reg40 & AVL_IRQ_ASSERTED) != 0) {
 		/* IRQ is being signaled */
 		reg_isr = readw(ndev->bmmio0 + REG_ISR);
-		if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) {
-			iret = netup_i2c_interrupt(&ndev->i2c[0]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) {
-			iret = netup_i2c_interrupt(&ndev->i2c[1]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_SPI) {
+		if (reg_isr & NETUP_UNIDVB_IRQ_SPI)
 			iret = netup_spi_interrupt(ndev->spi);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) {
-			iret = netup_dma_interrupt(&ndev->dma[0]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) {
-			iret = netup_dma_interrupt(&ndev->dma[1]);
-		} else if (reg_isr & NETUP_UNIDVB_IRQ_CI) {
-			iret = netup_ci_interrupt(ndev);
+		else if (!ndev->old_fw) {
+			if (reg_isr & NETUP_UNIDVB_IRQ_I2C0) {
+				iret = netup_i2c_interrupt(&ndev->i2c[0]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_I2C1) {
+				iret = netup_i2c_interrupt(&ndev->i2c[1]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA1) {
+				iret = netup_dma_interrupt(&ndev->dma[0]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_DMA2) {
+				iret = netup_dma_interrupt(&ndev->dma[1]);
+			} else if (reg_isr & NETUP_UNIDVB_IRQ_CI) {
+				iret = netup_ci_interrupt(ndev);
+			} else {
+				goto err;
+			}
 		} else {
+err:
 			dev_err(&pci_dev->dev,
 				"%s(): unknown interrupt 0x%x\n",
 				__func__, reg_isr);
-- 
2.33.0

[PATCH AUTOSEL 4.4 11/30] media: uvcvideo: Set capability in s_param

[Sasha Levin]

From: Ricardo Ribalda <ribalda@chromium.org>

[ Upstream commit 97a2777a96070afb7da5d587834086c0b586c8cc ]

Fixes v4l2-compliance:

Format ioctls (Input 0):
                warn: v4l2-test-formats.cpp(1339): S_PARM is supported but doesn't report V4L2_CAP_TIMEPERFRAME
                fail: v4l2-test-formats.cpp(1241): node->has_frmintervals && !cap->capability

Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/uvc/uvc_v4l2.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/media/usb/uvc/uvc_v4l2.c b/drivers/media/usb/uvc/uvc_v4l2.c
index 049d664e94f07..8ac231f6b2d16 100644
--- a/drivers/media/usb/uvc/uvc_v4l2.c
+++ b/drivers/media/usb/uvc/uvc_v4l2.c
@@ -436,10 +436,13 @@ static int uvc_v4l2_set_streamparm(struct uvc_streaming *stream,
 	uvc_simplify_fraction(&timeperframe.numerator,
 		&timeperframe.denominator, 8, 333);
 
-	if (parm->type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
+	if (parm->type == V4L2_BUF_TYPE_VIDEO_CAPTURE) {
 		parm->parm.capture.timeperframe = timeperframe;
-	else
+		parm->parm.capture.capability = V4L2_CAP_TIMEPERFRAME;
+	} else {
 		parm->parm.output.timeperframe = timeperframe;
+		parm->parm.output.capability = V4L2_CAP_TIMEPERFRAME;
+	}
 
 	return 0;
 }
-- 
2.33.0

[PATCH AUTOSEL 4.4 12/30] media: s5p-mfc: fix possible null-pointer dereference in s5p_mfc_probe()

[Sasha Levin]

From: Tuo Li <islituo@gmail.com>

[ Upstream commit 8515965e5e33f4feb56134348c95953f3eadfb26 ]

The variable pdev is assigned to dev->plat_dev, and dev->plat_dev is
checked in:
  if (!dev->plat_dev)

This indicates both dev->plat_dev and pdev can be NULL. If so, the
function dev_err() is called to print error information.
  dev_err(&pdev->dev, "No platform data specified\n");

However, &pdev->dev is an illegal address, and it is dereferenced in
dev_err().

To fix this possible null-pointer dereference, replace dev_err() with
mfc_err().

Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Tuo Li <islituo@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/platform/s5p-mfc/s5p_mfc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc.c b/drivers/media/platform/s5p-mfc/s5p_mfc.c
index 7727789dbda14..daa5b4dea092c 100644
--- a/drivers/media/platform/s5p-mfc/s5p_mfc.c
+++ b/drivers/media/platform/s5p-mfc/s5p_mfc.c
@@ -1102,7 +1102,7 @@ static int s5p_mfc_probe(struct platform_device *pdev)
 	spin_lock_init(&dev->condlock);
 	dev->plat_dev = pdev;
 	if (!dev->plat_dev) {
-		dev_err(&pdev->dev, "No platform data specified\n");
+		mfc_err("No platform data specified\n");
 		return -ENODEV;
 	}
 
-- 
2.33.0

[PATCH AUTOSEL 4.4 13/30] media: mceusb: return without resubmitting URB in case of -EPROTO error.

[Sasha Levin]

From: Rajat Asthana <rajatasthana4@gmail.com>

[ Upstream commit 476db72e521983ecb847e4013b263072bb1110fc ]

Syzkaller reported a warning called "rcu detected stall in dummy_timer".

The error seems to be an error in mceusb_dev_recv(). In the case of
-EPROTO error, the routine immediately resubmits the URB. Instead it
should return without resubmitting URB.

Reported-by: syzbot+4d3749e9612c2cfab956@syzkaller.appspotmail.com
Signed-off-by: Rajat Asthana <rajatasthana4@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/rc/mceusb.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/media/rc/mceusb.c b/drivers/media/rc/mceusb.c
index 0fba4a2c16028..7b9800d3446cf 100644
--- a/drivers/media/rc/mceusb.c
+++ b/drivers/media/rc/mceusb.c
@@ -1079,6 +1079,7 @@ static void mceusb_dev_recv(struct urb *urb)
 	case -ECONNRESET:
 	case -ENOENT:
 	case -EILSEQ:
+	case -EPROTO:
 	case -ESHUTDOWN:
 		usb_unlink_urb(urb);
 		return;
-- 
2.33.0

[PATCH AUTOSEL 4.4 16/30] media: usb: dvd-usb: fix uninit-value bug in dibusb_read_eeprom_byte()

[Sasha Levin]

From: Anant Thazhemadam <anant.thazhemadam@gmail.com>

[ Upstream commit 899a61a3305d49e8a712e9ab20d0db94bde5929f ]

In dibusb_read_eeprom_byte(), if dibusb_i2c_msg() fails, val gets
assigned an value that's not properly initialized.
Using kzalloc() in place of kmalloc() for the buffer fixes this issue,
as the val can now be set to 0 in the event dibusb_i2c_msg() fails.

Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Tested-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com
Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/media/usb/dvb-usb/dibusb-common.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/media/usb/dvb-usb/dibusb-common.c b/drivers/media/usb/dvb-usb/dibusb-common.c
index 7b15aea2723d6..5a1dc0d465d26 100644
--- a/drivers/media/usb/dvb-usb/dibusb-common.c
+++ b/drivers/media/usb/dvb-usb/dibusb-common.c
@@ -182,7 +182,7 @@ int dibusb_read_eeprom_byte(struct dvb_usb_device *d, u8 offs, u8 *val)
 	u8 *buf;
 	int rc;
 
-	buf = kmalloc(2, GFP_KERNEL);
+	buf = kzalloc(2, GFP_KERNEL);
 	if (!buf)
 		return -ENOMEM;
 
-- 
2.33.0