From: Jacopo Mondi <jacopo@jmondi.org>
To: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: paul.j.murphy@intel.com, daniele.alessandrelli@intel.com,
linux-media@vger.kernel.org
Subject: Re: [PATCH 04/16] media: i2c: ov9282: Remove pixel rate from mode definition
Date: Thu, 6 Oct 2022 11:17:30 +0200 [thread overview]
Message-ID: <20221006091730.mtphbem33dufubd4@uno.localdomain> (raw)
In-Reply-To: <20221005152809.3785786-5-dave.stevenson@raspberrypi.com>
Hi Dave
On Wed, Oct 05, 2022 at 04:27:57PM +0100, Dave Stevenson wrote:
> The pixel rate is determined by the PLL setup in the common
> registers, not by the mode specific registers, therefore
> remove it from the mode definition and define it for all modes.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
> ---
> drivers/media/i2c/ov9282.c | 17 +++++++----------
> 1 file changed, 7 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/media/i2c/ov9282.c b/drivers/media/i2c/ov9282.c
> index 1c77b77427f0..798ff8ba50bd 100644
> --- a/drivers/media/i2c/ov9282.c
> +++ b/drivers/media/i2c/ov9282.c
> @@ -53,6 +53,10 @@
> #define OV9282_LINK_FREQ 400000000
> #define OV9282_NUM_DATA_LANES 2
>
> +/* Pixel rate */
> +#define OV9282_PIXEL_RATE (OV9282_LINK_FREQ * 2 * \
> + OV9282_NUM_DATA_LANES / 10)
This will work as long as there's a single Y10 supported mode.
I haven't looked at the rest of the series yet but if Y8 gets
supported it might be worth dynamically re-computing the PIXEL_RATE
when a new mode is applied.
For now this is good, and if Y10 remains the default format is fine to
initialize PIXEL_RATE assuming 10 bpp
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Thanks
j
> +
> #define OV9282_REG_MIN 0x00
> #define OV9282_REG_MAX 0xfffff
>
> @@ -92,7 +96,6 @@ struct ov9282_reg_list {
> * @vblank: Vertical blanking in lines
> * @vblank_min: Minimum vertical blanking in lines
> * @vblank_max: Maximum vertical blanking in lines
> - * @pclk: Sensor pixel clock
> * @link_freq_idx: Link frequency index
> * @reg_list: Register list for sensor mode
> */
> @@ -103,7 +106,6 @@ struct ov9282_mode {
> u32 vblank;
> u32 vblank_min;
> u32 vblank_max;
> - u64 pclk;
> u32 link_freq_idx;
> struct ov9282_reg_list reg_list;
> };
> @@ -118,7 +120,6 @@ struct ov9282_mode {
> * @inclk: Sensor input clock
> * @ctrl_handler: V4L2 control handler
> * @link_freq_ctrl: Pointer to link frequency control
> - * @pclk_ctrl: Pointer to pixel clock control
> * @hblank_ctrl: Pointer to horizontal blanking control
> * @vblank_ctrl: Pointer to vertical blanking control
> * @exp_ctrl: Pointer to exposure control
> @@ -138,7 +139,6 @@ struct ov9282 {
> struct regulator_bulk_data supplies[OV9282_NUM_SUPPLIES];
> struct v4l2_ctrl_handler ctrl_handler;
> struct v4l2_ctrl *link_freq_ctrl;
> - struct v4l2_ctrl *pclk_ctrl;
> struct v4l2_ctrl *hblank_ctrl;
> struct v4l2_ctrl *vblank_ctrl;
> struct {
> @@ -269,7 +269,6 @@ static const struct ov9282_mode supported_mode = {
> .vblank = 1022,
> .vblank_min = 151,
> .vblank_max = 51540,
> - .pclk = 160000000,
> .link_freq_idx = 0,
> .reg_list = {
> .num_of_regs = ARRAY_SIZE(mode_1280x720_regs),
> @@ -1006,11 +1005,9 @@ static int ov9282_init_controls(struct ov9282 *ov9282)
> 1, mode->vblank);
>
> /* Read only controls */
> - ov9282->pclk_ctrl = v4l2_ctrl_new_std(ctrl_hdlr,
> - &ov9282_ctrl_ops,
> - V4L2_CID_PIXEL_RATE,
> - mode->pclk, mode->pclk,
> - 1, mode->pclk);
> + v4l2_ctrl_new_std(ctrl_hdlr, &ov9282_ctrl_ops, V4L2_CID_PIXEL_RATE,
> + OV9282_PIXEL_RATE, OV9282_PIXEL_RATE, 1,
> + OV9282_PIXEL_RATE);
>
> ov9282->link_freq_ctrl = v4l2_ctrl_new_int_menu(ctrl_hdlr,
> &ov9282_ctrl_ops,
> --
> 2.34.1
>
next prev parent reply other threads:[~2022-10-06 9:17 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-10-05 15:27 [PATCH 00/16] Updates to ov9282 sensor driver Dave Stevenson
2022-10-05 15:27 ` [PATCH 01/16] media: i2c: ov9282: Remove duplication of registers Dave Stevenson
2022-10-06 9:14 ` Jacopo Mondi
2022-10-05 15:27 ` [PATCH 02/16] media: i2c: ov9282: Split registers into common and mode specific Dave Stevenson
2022-10-06 9:15 ` Jacopo Mondi
2022-10-05 15:27 ` [PATCH 03/16] media: i2c: ov9282: Remove format code from the mode Dave Stevenson
2022-10-06 9:15 ` Jacopo Mondi
2022-10-05 15:27 ` [PATCH 04/16] media: i2c: ov9282: Remove pixel rate from mode definition Dave Stevenson
2022-10-06 9:17 ` Jacopo Mondi [this message]
2022-10-06 11:51 ` Dave Stevenson
2022-10-05 15:27 ` [PATCH 05/16] media: i2c: ov9281: Support more than 1 mode Dave Stevenson
2022-10-06 9:18 ` Jacopo Mondi
2022-10-26 7:22 ` Sakari Ailus
2022-10-05 15:27 ` [PATCH 06/16] media: i2c: ov9282: Correct HTS register for configured pixel rate Dave Stevenson
2022-10-06 9:23 ` Jacopo Mondi
2022-10-06 13:01 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 07/16] media: i2c: ov9282: Reduce vblank_min values based on testing Dave Stevenson
2022-10-06 11:56 ` Jacopo Mondi
2022-10-06 13:02 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 08/16] media: i2c: ov9282: Add selection for CSI2 clock mode Dave Stevenson
2022-10-06 9:24 ` Jacopo Mondi
2022-10-26 7:21 ` Sakari Ailus
2022-10-28 12:57 ` Dave Stevenson
2022-10-28 14:30 ` Sakari Ailus
2022-10-28 15:03 ` Dave Stevenson
2022-10-31 13:06 ` Sakari Ailus
2022-10-05 15:28 ` [PATCH 09/16] media: i2c: ov9282: Add the properties from fwnode Dave Stevenson
2022-10-06 11:57 ` Jacopo Mondi
2022-10-05 15:28 ` [PATCH 10/16] media: i2c: ov9282: Action CID_VBLANK when set Dave Stevenson
2022-10-06 9:29 ` Jacopo Mondi
2022-10-06 13:21 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 11/16] media: i2c: ov9282: Add HFLIP and VFLIP support Dave Stevenson
2022-10-06 9:38 ` Jacopo Mondi
2022-10-06 14:21 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 12/16] media: i2c: ov9282: Make V4L2_CID_HBLANK r/w Dave Stevenson
2022-10-06 9:41 ` Jacopo Mondi
2022-10-06 11:33 ` Dave Stevenson
2022-10-06 11:53 ` Jacopo Mondi
2022-10-05 15:28 ` [PATCH 13/16] media: i2c: ov9282: Add selection API calls for cropping info Dave Stevenson
2022-10-06 9:43 ` Jacopo Mondi
2022-10-06 11:39 ` Dave Stevenson
2022-10-06 11:54 ` Jacopo Mondi
2022-10-05 15:28 ` [PATCH 14/16] media: i2c: ov9282: Add support for 1280x800 and 640x400 modes Dave Stevenson
2022-10-06 9:48 ` Jacopo Mondi
2022-10-06 11:46 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 15/16] media: i2c: ov9282: Add support for 8bit readout Dave Stevenson
2022-10-06 9:57 ` Jacopo Mondi
2022-10-06 12:20 ` Dave Stevenson
2022-10-05 15:28 ` [PATCH 16/16] media: i2c: ov9282: Support event handlers Dave Stevenson
2022-10-06 9:59 ` Jacopo Mondi
2022-10-07 10:22 ` Dave Stevenson
2022-10-07 12:57 ` Jacopo Mondi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221006091730.mtphbem33dufubd4@uno.localdomain \
--to=jacopo@jmondi.org \
--cc=daniele.alessandrelli@intel.com \
--cc=dave.stevenson@raspberrypi.com \
--cc=linux-media@vger.kernel.org \
--cc=paul.j.murphy@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).