* [PATCH v4 1/3] dt-bindings: ov2680: convert bindings to yaml
2020-10-20 9:19 [PATCH v4 0/3] dt-bindings: media: imx7 and ov2680 updates to yaml Rui Miguel Silva
@ 2020-10-20 9:19 ` Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 2/3] dt-bindings: imx7-csi: " Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: " Rui Miguel Silva
2 siblings, 0 replies; 8+ messages in thread
From: Rui Miguel Silva @ 2020-10-20 9:19 UTC (permalink / raw)
To: Rob Herring, sakari.ailus, Hans Verkuil, Jacopo Mondi
Cc: linux-media, devicetree, Rui Miguel Silva, Jacopo Mondi
Convert ov2680 sensor bindings documentation to yaml schema, remove
the textual bindings document and update MAINTAINERS entry.
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
v3 -> v4:
Rob Herring:
https://lore.kernel.org/linux-media/20201019203910.GB3550266@bogus/
- remove clock-names description
- add maxItems to reset-gpios
.../devicetree/bindings/media/i2c/ov2680.txt | 46 ---------
.../bindings/media/i2c/ovti,ov2680.yaml | 99 +++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 100 insertions(+), 47 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov2680.txt
create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
deleted file mode 100644
index 11e925ed9dad..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ov2680.txt
+++ /dev/null
@@ -1,46 +0,0 @@
-* Omnivision OV2680 MIPI CSI-2 sensor
-
-Required Properties:
-- compatible: should be "ovti,ov2680".
-- clocks: reference to the xvclk input clock.
-- clock-names: should be "xvclk".
-- DOVDD-supply: Digital I/O voltage supply.
-- DVDD-supply: Digital core voltage supply.
-- AVDD-supply: Analog voltage supply.
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
- if any. This is an active low signal to the OV2680.
-
-The device node must contain one 'port' child node for its digital output
-video port, and this port must have a single endpoint in accordance with
- the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-Endpoint node required properties for CSI-2 connection are:
-- remote-endpoint: a phandle to the bus receiver's endpoint node.
-- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
-- data-lanes: should be set to <1> (one CSI-2 lane supported).
-
-Example:
-
-&i2c2 {
- ov2680: camera-sensor@36 {
- compatible = "ovti,ov2680";
- reg = <0x36>;
- clocks = <&osc>;
- clock-names = "xvclk";
- reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
- DOVDD-supply = <&sw2_reg>;
- DVDD-supply = <&sw2_reg>;
- AVDD-supply = <®_peri_3p15v>;
-
- port {
- ov2680_to_mipi: endpoint {
- remote-endpoint = <&mipi_from_sensor>;
- clock-lanes = <0>;
- data-lanes = <1>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
new file mode 100644
index 000000000000..43bf749807e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ovti,ov2680.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Omnivision OV2680 CMOS Sensor
+
+maintainers:
+ - Rui Miguel Silva <rmfrfs@gmail.com>
+
+description: |-
+ The OV2680 color sensor is a low voltage, high performance 1/5 inch UXGA (2
+ megapixel) CMOS image sensor that provides a single-chip UXGA (1600 x 1200)
+ camera. It provides full-frame, sub-sampled, or windowed 10-bit images in
+ various formats via the control of the Serial Camera Control Bus (SCCB)
+ interface. The OV2680 has an image array capable of operating at up to 30
+ frames per second (fps) in UXGA resolution.
+
+properties:
+ compatible:
+ const: ovti,ov2680
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ const: xvclk
+
+ reset-gpios:
+ description:
+ The phandle and specifier for the GPIO that controls sensor reset.
+ This corresponds to the hardware pin XSHUTDOWN which is physically
+ active low.
+ maxItems: 1
+
+ dovdd-supply:
+ description:
+ Definition of the regulator used as interface power supply.
+
+ avdd-supply:
+ description:
+ Definition of the regulator used as analog power supply.
+
+ dvdd-supply:
+ description:
+ Definition of the regulator used as digital power supply.
+
+ port:
+ type: object
+ description:
+ A node containing an output port node with an endpoint definition
+ as documented in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - dovdd-supply
+ - avdd-supply
+ - dvdd-supply
+ - reset-gpios
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov2680: camera-sensor@36 {
+ compatible = "ovti,ov2680";
+ reg = <0x36>;
+ clocks = <&osc>;
+ clock-names = "xvclk";
+ reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+
+ dovdd-supply = <&sw2_reg>;
+ dvdd-supply = <&sw2_reg>;
+ avdd-supply = <®_peri_3p15v>;
+
+ port {
+ ov2680_to_mipi: endpoint {
+ remote-endpoint = <&mipi_from_sensor>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index f2757c6068e3..2cb2a5c60a1d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12781,7 +12781,7 @@ M: Rui Miguel Silva <rmfrfs@gmail.com>
L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media_tree.git
-F: Documentation/devicetree/bindings/media/i2c/ov2680.txt
+F: Documentation/devicetree/bindings/media/i2c/ov2680.yaml
F: drivers/media/i2c/ov2680.c
OMNIVISION OV2685 SENSOR DRIVER
--
2.28.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 2/3] dt-bindings: imx7-csi: convert bindings to yaml
2020-10-20 9:19 [PATCH v4 0/3] dt-bindings: media: imx7 and ov2680 updates to yaml Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 1/3] dt-bindings: ov2680: convert bindings " Rui Miguel Silva
@ 2020-10-20 9:19 ` Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: " Rui Miguel Silva
2 siblings, 0 replies; 8+ messages in thread
From: Rui Miguel Silva @ 2020-10-20 9:19 UTC (permalink / raw)
To: Rob Herring, sakari.ailus, Hans Verkuil, Jacopo Mondi
Cc: linux-media, devicetree, Rui Miguel Silva, Jacopo Mondi
Convert imx7-csi bindings documentation to yaml schema, remove the
textual bindings document and update MAINTAINERS entry.
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
---
.../devicetree/bindings/media/imx7-csi.txt | 42 -----------
.../bindings/media/nxp,imx7-csi.yaml | 71 +++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 72 insertions(+), 43 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/imx7-csi.txt
create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt
deleted file mode 100644
index d80ceefa0c00..000000000000
--- a/Documentation/devicetree/bindings/media/imx7-csi.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-Freescale i.MX7 CMOS Sensor Interface
-=====================================
-
-csi node
---------
-
-This is device node for the CMOS Sensor Interface (CSI) which enables the chip
-to connect directly to external CMOS image sensors.
-
-Required properties:
-
-- compatible : "fsl,imx7-csi" or "fsl,imx6ul-csi";
-- reg : base address and length of the register set for the device;
-- interrupts : should contain CSI interrupt;
-- clocks : list of clock specifiers, see
- Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
-- clock-names : must contain "mclk";
-
-The device node shall contain one 'port' child node with one child 'endpoint'
-node, according to the bindings defined in:
-Documentation/devicetree/bindings/media/video-interfaces.txt.
-
-In the following example a remote endpoint is a video multiplexer.
-
-example:
-
- csi: csi@30710000 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- compatible = "fsl,imx7-csi";
- reg = <0x30710000 0x10000>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>;
- clock-names = "mclk";
-
- port {
- csi_from_csi_mux: endpoint {
- remote-endpoint = <&csi_mux_to_csi>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml b/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
new file mode 100644
index 000000000000..4e81a47e60ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/nxp,imx7-csi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX7 CMOS Sensor Interface
+
+maintainers:
+ - Rui Miguel Silva <rmfrfs@gmail.com>
+
+description: |
+ This is device node for the CMOS Sensor Interface (CSI) which enables the
+ chip to connect directly to external CMOS image sensors.
+
+properties:
+ compatible:
+ enum:
+ - fsl,imx7-csi
+ - fsl,imx6ul-csi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-names:
+ items:
+ - const: mclk
+
+ port:
+ type: object
+ description:
+ A node containing input port nodes with endpoint definitions as documented
+ in Documentation/devicetree/bindings/media/video-interfaces.txt
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - port
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx7d-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ csi: csi@30710000 {
+ compatible = "fsl,imx7-csi";
+ reg = <0x30710000 0x10000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>;
+ clock-names = "mclk";
+
+ port {
+ csi_from_csi_mux: endpoint {
+ remote-endpoint = <&csi_mux_to_csi>;
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 2cb2a5c60a1d..557713b3ee95 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10779,8 +10779,8 @@ L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media_tree.git
F: Documentation/admin-guide/media/imx7.rst
-F: Documentation/devicetree/bindings/media/imx7-csi.txt
F: Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
+F: Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
F: drivers/staging/media/imx/imx7-media-csi.c
F: drivers/staging/media/imx/imx7-mipi-csis.c
--
2.28.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: convert bindings to yaml
2020-10-20 9:19 [PATCH v4 0/3] dt-bindings: media: imx7 and ov2680 updates to yaml Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 1/3] dt-bindings: ov2680: convert bindings " Rui Miguel Silva
2020-10-20 9:19 ` [PATCH v4 2/3] dt-bindings: imx7-csi: " Rui Miguel Silva
@ 2020-10-20 9:19 ` Rui Miguel Silva
2020-10-20 15:30 ` Rob Herring
2 siblings, 1 reply; 8+ messages in thread
From: Rui Miguel Silva @ 2020-10-20 9:19 UTC (permalink / raw)
To: Rob Herring, sakari.ailus, Hans Verkuil, Jacopo Mondi
Cc: linux-media, devicetree, Rui Miguel Silva
Convert imx7 mipi csi2 bindings documentation to yaml schema, remove
the textual document and update MAINTAINERS entry.
Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
---
.../bindings/media/imx7-mipi-csi2.txt | 90 ---------
.../bindings/media/nxp,imx7-mipi-csi2.yaml | 172 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 173 insertions(+), 91 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
deleted file mode 100644
index 71fd74ed3ec8..000000000000
--- a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
+++ /dev/null
@@ -1,90 +0,0 @@
-Freescale i.MX7 Mipi CSI2
-=========================
-
-mipi_csi2 node
---------------
-
-This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is
-compatible with previous version of Samsung D-phy.
-
-Required properties:
-
-- compatible : "fsl,imx7-mipi-csi2";
-- reg : base address and length of the register set for the device;
-- interrupts : should contain MIPI CSIS interrupt;
-- clocks : list of clock specifiers, see
- Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
-- clock-names : must contain "pclk", "wrap" and "phy" entries, matching
- entries in the clock property;
-- power-domains : a phandle to the power domain, see
- Documentation/devicetree/bindings/power/power_domain.txt for details.
-- reset-names : should include following entry "mrst";
-- resets : a list of phandle, should contain reset entry of
- reset-names;
-- phy-supply : from the generic phy bindings, a phandle to a regulator that
- provides power to MIPI CSIS core;
-
-Optional properties:
-
-- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
- value when this property is not specified is 166 MHz;
-- fsl,csis-hs-settle : differential receiver (HS-RX) settle time;
-
-The device node should contain two 'port' child nodes with one child 'endpoint'
-node, according to the bindings defined in:
- Documentation/devicetree/bindings/ media/video-interfaces.txt.
- The following are properties specific to those nodes.
-
-port node
----------
-
-- reg : (required) can take the values 0 or 1, where 0 shall be
- related to the sink port and port 1 shall be the source
- one;
-
-endpoint node
--------------
-
-- data-lanes : (required) an array specifying active physical MIPI-CSI2
- data input lanes and their mapping to logical lanes; this
- shall only be applied to port 0 (sink port), the array's
- content is unused only its length is meaningful,
- in this case the maximum length supported is 2;
-
-example:
-
- mipi_csi: mipi-csi@30750000 {
- #address-cells = <1>;
- #size-cells = <0>;
-
- compatible = "fsl,imx7-mipi-csi2";
- reg = <0x30750000 0x10000>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_IPG_ROOT_CLK>,
- <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
- <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
- clock-names = "pclk", "wrap", "phy";
- clock-frequency = <166000000>;
- power-domains = <&pgc_mipi_phy>;
- phy-supply = <®_1p0d>;
- resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
- reset-names = "mrst";
- fsl,csis-hs-settle = <3>;
-
- port@0 {
- reg = <0>;
-
- mipi_from_sensor: endpoint {
- remote-endpoint = <&ov2680_to_mipi>;
- data-lanes = <1>;
- };
- };
-
- port@1 {
- reg = <1>;
-
- mipi_vc0_to_csi_mux: endpoint {
- remote-endpoint = <&csi_mux_from_mipi_vc0>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml b/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
new file mode 100644
index 000000000000..dfbae2e72c60
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
@@ -0,0 +1,172 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/nxp,imx7-mipi-csi2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX7 Mipi CSI2
+
+maintainers:
+ - Rui Miguel Silva <rmfrfs@gmail.com>
+
+description: |
+ This is the device node for the mipi csi-2 receiver core in i.mx7 soc. It is
+ compatible with previous version of samsung d-phy.
+
+properties:
+ compatible:
+ const: fsl,imx7-mipi-csi2
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 3
+
+ clock-names:
+ items:
+ - const: pclk
+ - const: wrap
+ - const: phy
+
+ power-domains:
+ maxItems: 1
+
+ phy-supply:
+ description:
+ Phandle to a regulator that provides power to the PHY. This
+ regulator will be managed during the PHY power on/off sequence.
+
+ resets:
+ maxItems: 1
+
+ reset-names:
+ const: mrst
+
+ clock-frequency:
+ description:
+ The IP main (system bus) clock frequency in Hertz
+ default: 166000000
+
+ fsl,csis-hs-settle:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Differential receiver (HS-RX) settle time
+
+ ports:
+ type: object
+ description:
+ A node containing input and output port nodes with endpoint definitions
+ as documented in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ properties:
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ port@0:
+ type: object
+ description:
+ Input port node, single endpoint describing the CSI-2 transmitter.
+
+ properties:
+ reg:
+ const: 0
+
+ endpoint:
+ type: object
+
+ properties:
+ data-lanes:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: See ../video-interfaces.txt
+ oneOf:
+ - items:
+ - const: 1
+ - items:
+ - const: 1
+ - const: 2
+
+ remote-endpoint: true
+
+ required:
+ - data-lanes
+ - remote-endpoint
+
+ additionalProperties: false
+
+ additionalProperties: false
+
+ port@1:
+ type: object
+ description:
+ Output port node
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - clock-names
+ - power-domains
+ - phy-supply
+ - resets
+ - reset-names
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx7d-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/reset/imx7-reset.h>
+
+ mipi_csi: mipi-csi@30750000 {
+ compatible = "fsl,imx7-mipi-csi2";
+ reg = <0x30750000 0x10000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&clks IMX7D_IPG_ROOT_CLK>,
+ <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
+ <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
+ clock-names = "pclk", "wrap", "phy";
+ clock-frequency = <166000000>;
+
+ power-domains = <&pgc_mipi_phy>;
+ phy-supply = <®_1p0d>;
+ resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
+ reset-names = "mrst";
+ fsl,csis-hs-settle = <3>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ mipi_from_sensor: endpoint {
+ remote-endpoint = <&ov2680_to_mipi>;
+ data-lanes = <1>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ mipi_vc0_to_csi_mux: endpoint {
+ remote-endpoint = <&csi_mux_from_mipi_vc0>;
+ };
+ };
+ };
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 557713b3ee95..34e53a1570aa 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -10779,8 +10779,8 @@ L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media_tree.git
F: Documentation/admin-guide/media/imx7.rst
-F: Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
F: Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
+F: Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
F: drivers/staging/media/imx/imx7-media-csi.c
F: drivers/staging/media/imx/imx7-mipi-csis.c
--
2.28.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: convert bindings to yaml
2020-10-20 9:19 ` [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: " Rui Miguel Silva
@ 2020-10-20 15:30 ` Rob Herring
2020-10-20 18:52 ` Rui Miguel Silva
0 siblings, 1 reply; 8+ messages in thread
From: Rob Herring @ 2020-10-20 15:30 UTC (permalink / raw)
To: Rui Miguel Silva
Cc: Hans Verkuil, sakari.ailus, Jacopo Mondi, linux-media,
Rob Herring, devicetree
On Tue, 20 Oct 2020 10:19:21 +0100, Rui Miguel Silva wrote:
> Convert imx7 mipi csi2 bindings documentation to yaml schema, remove
> the textual document and update MAINTAINERS entry.
>
> Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
> ---
> .../bindings/media/imx7-mipi-csi2.txt | 90 ---------
> .../bindings/media/nxp,imx7-mipi-csi2.yaml | 172 ++++++++++++++++++
> MAINTAINERS | 2 +-
> 3 files changed, 173 insertions(+), 91 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
>
My bot found errors running 'make dt_binding_check' on your patch:
./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:91:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:93:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
See https://patchwork.ozlabs.org/patch/1384742
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure dt-schema is up to date:
pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: convert bindings to yaml
2020-10-20 15:30 ` Rob Herring
@ 2020-10-20 18:52 ` Rui Miguel Silva
2020-10-21 13:05 ` Rob Herring
0 siblings, 1 reply; 8+ messages in thread
From: Rui Miguel Silva @ 2020-10-20 18:52 UTC (permalink / raw)
To: Rob Herring
Cc: Hans Verkuil, sakari.ailus, Jacopo Mondi, linux-media,
Rob Herring, devicetree
Hi Rob Bot,
On Tue, Oct 20, 2020 at 10:30:44AM -0500, Rob Herring wrote:
> On Tue, 20 Oct 2020 10:19:21 +0100, Rui Miguel Silva wrote:
> > Convert imx7 mipi csi2 bindings documentation to yaml schema, remove
> > the textual document and update MAINTAINERS entry.
> >
> > Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
> > ---
> > .../bindings/media/imx7-mipi-csi2.txt | 90 ---------
> > .../bindings/media/nxp,imx7-mipi-csi2.yaml | 172 ++++++++++++++++++
> > MAINTAINERS | 2 +-
> > 3 files changed, 173 insertions(+), 91 deletions(-)
> > delete mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> > create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
> >
>
>
> My bot found errors running 'make dt_binding_check' on your patch:
>
> ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:91:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
> ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:93:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
Strange not to complain on line 94 also.
>
>
> See https://patchwork.ozlabs.org/patch/1384742
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure dt-schema is up to date:
>
> pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
I have done this and I am at version:
2020.8.2.dev4+g341f3e35180a
and still do not get any warning on this file. Nevertheless I
found the indentation issue and will:
> Please check and re-submit.
------
Cheers,
Rui
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: convert bindings to yaml
2020-10-20 18:52 ` Rui Miguel Silva
@ 2020-10-21 13:05 ` Rob Herring
2020-10-21 20:51 ` Rui Miguel Silva
0 siblings, 1 reply; 8+ messages in thread
From: Rob Herring @ 2020-10-21 13:05 UTC (permalink / raw)
To: Rui Miguel Silva
Cc: Hans Verkuil, Sakari Ailus, Jacopo Mondi,
Linux Media Mailing List, devicetree
On Tue, Oct 20, 2020 at 1:52 PM Rui Miguel Silva <rmfrfs@gmail.com> wrote:
>
> Hi Rob Bot,
> On Tue, Oct 20, 2020 at 10:30:44AM -0500, Rob Herring wrote:
> > On Tue, 20 Oct 2020 10:19:21 +0100, Rui Miguel Silva wrote:
> > > Convert imx7 mipi csi2 bindings documentation to yaml schema, remove
> > > the textual document and update MAINTAINERS entry.
> > >
> > > Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
> > > ---
> > > .../bindings/media/imx7-mipi-csi2.txt | 90 ---------
> > > .../bindings/media/nxp,imx7-mipi-csi2.yaml | 172 ++++++++++++++++++
> > > MAINTAINERS | 2 +-
> > > 3 files changed, 173 insertions(+), 91 deletions(-)
> > > delete mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> > > create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
> > >
> >
> >
> > My bot found errors running 'make dt_binding_check' on your patch:
> >
> > ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:91:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
> > ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:93:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
>
> Strange not to complain on line 94 also.
>
> >
> >
> > See https://patchwork.ozlabs.org/patch/1384742
> >
> > If you already ran 'make dt_binding_check' and didn't see the above
> > error(s), then make sure dt-schema is up to date:
> >
> > pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
>
> I have done this and I am at version:
> 2020.8.2.dev4+g341f3e35180a
>
> and still do not get any warning on this file. Nevertheless I
> found the indentation issue and will:
It's coming from yamllint which is recently added (this merge window)
and is optionally run if yamllint is present. Will clarify this in the
email.
Rob
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 3/3] dt-bindings: imx7-mipi-csi2: convert bindings to yaml
2020-10-21 13:05 ` Rob Herring
@ 2020-10-21 20:51 ` Rui Miguel Silva
0 siblings, 0 replies; 8+ messages in thread
From: Rui Miguel Silva @ 2020-10-21 20:51 UTC (permalink / raw)
To: Rob Herring
Cc: Hans Verkuil, Sakari Ailus, Jacopo Mondi,
Linux Media Mailing List, devicetree
Hi Rob,
On Wed, Oct 21, 2020 at 08:05:53AM -0500, Rob Herring wrote:
> On Tue, Oct 20, 2020 at 1:52 PM Rui Miguel Silva <rmfrfs@gmail.com> wrote:
> >
> > Hi Rob Bot,
> > On Tue, Oct 20, 2020 at 10:30:44AM -0500, Rob Herring wrote:
> > > On Tue, 20 Oct 2020 10:19:21 +0100, Rui Miguel Silva wrote:
> > > > Convert imx7 mipi csi2 bindings documentation to yaml schema, remove
> > > > the textual document and update MAINTAINERS entry.
> > > >
> > > > Signed-off-by: Rui Miguel Silva <rmfrfs@gmail.com>
> > > > ---
> > > > .../bindings/media/imx7-mipi-csi2.txt | 90 ---------
> > > > .../bindings/media/nxp,imx7-mipi-csi2.yaml | 172 ++++++++++++++++++
> > > > MAINTAINERS | 2 +-
> > > > 3 files changed, 173 insertions(+), 91 deletions(-)
> > > > delete mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
> > > > create mode 100644 Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml
> > > >
> > >
> > >
> > > My bot found errors running 'make dt_binding_check' on your patch:
> > >
> > > ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:91:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
> > > ./Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml:93:21: [warning] wrong indentation: expected 22 but found 20 (indentation)
> >
> > Strange not to complain on line 94 also.
> >
> > >
> > >
> > > See https://patchwork.ozlabs.org/patch/1384742
> > >
> > > If you already ran 'make dt_binding_check' and didn't see the above
> > > error(s), then make sure dt-schema is up to date:
> > >
> > > pip3 install git+https://github.com/devicetree-org/dt-schema.git@master --upgrade
> >
> > I have done this and I am at version:
> > 2020.8.2.dev4+g341f3e35180a
> >
> > and still do not get any warning on this file. Nevertheless I
> > found the indentation issue and will:
>
> It's coming from yamllint which is recently added (this merge window)
> and is optionally run if yamllint is present. Will clarify this in the
> email.
Got it, thanks for the explanation.
------
Cheers,
Rui
^ permalink raw reply [flat|nested] 8+ messages in thread