[PATCH v2 1/5] dt-bindings: phy: mediatek: tphy: support software efuse load

[PATCH v2 1/5] dt-bindings: phy: mediatek: tphy: support software efuse load

[Chunfeng Yun]

Add optional property nvmem-cells and nvmem-cell-names to support
software efuse load, this helps to fix the efuse bit shift issue
on mt8195 etc.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: add acked-by Rob
---
 .../devicetree/bindings/phy/mediatek,tphy.yaml | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 9e6c0f43f1c6..05ee274b4b71 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -160,6 +160,24 @@ patternProperties:
                 - PHY_TYPE_PCIE
                 - PHY_TYPE_SATA
 
+      nvmem-cells:
+        items:
+          - description: internal R efuse for U2 PHY or U3/PCIe PHY
+          - description: rx_imp_sel efuse for U3/PCIe PHY
+          - description: tx_imp_sel efuse for U3/PCIe PHY
+        description: |
+          Phandles to nvmem cell that contains the efuse data;
+          Available only for U2 PHY or U3/PCIe PHY of version 2/3, these
+          three items should be provided at the same time for U3/PCIe PHY,
+          when use software to load efuse;
+          If unspecified, will use hardware auto-load efuse.
+
+      nvmem-cell-names:
+        items:
+          - const: intr
+          - const: rx_imp
+          - const: tx_imp
+
       # The following optional vendor properties are only for debug or HQA test
       mediatek,eye-src:
         description:
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 2/5] phy: phy-mtk-tphy: add support efuse setting

[Chunfeng Yun]

Due to some SoCs have a bit shift issue that will drop a bit for usb3
phy or pcie phy, fix it by adding software efuse reading and setting,
but only support it optionally for version 2/3.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: changes suggested by Vinod
    1. fix typo of version in commit message
    2. use dev_dbg() instead of dev_info()
---
 drivers/phy/mediatek/phy-mtk-tphy.c | 162 ++++++++++++++++++++++++++++
 1 file changed, 162 insertions(+)

diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index cdcef865fe9e..98a942c607a6 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -12,6 +12,7 @@
 #include <linux/iopoll.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
+#include <linux/nvmem-consumer.h>
 #include <linux/of_address.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
@@ -41,6 +42,9 @@
 #define SSUSB_SIFSLV_V2_U3PHYD		0x200
 #define SSUSB_SIFSLV_V2_U3PHYA		0x400
 
+#define U3P_MISC_REG1		0x04
+#define MR1_EFUSE_AUTO_LOAD_DIS		BIT(6)
+
 #define U3P_USBPHYACR0		0x000
 #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
 #define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
@@ -133,6 +137,8 @@
 #define P3C_RG_SWRST_U3_PHYD_FORCE_EN	BIT(24)
 
 #define U3P_U3_PHYA_REG0	0x000
+#define P3A_RG_IEXT_INTR		GENMASK(15, 10)
+#define P3A_RG_IEXT_INTR_VAL(x)		((0x3f & (x)) << 10)
 #define P3A_RG_CLKDRV_OFF		GENMASK(3, 2)
 #define P3A_RG_CLKDRV_OFF_VAL(x)	((0x3 & (x)) << 2)
 
@@ -187,6 +193,19 @@
 #define P3D_RG_FWAKE_TH		GENMASK(21, 16)
 #define P3D_RG_FWAKE_TH_VAL(x)	((0x3f & (x)) << 16)
 
+#define U3P_U3_PHYD_IMPCAL0		0x010
+#define P3D_RG_FORCE_TX_IMPEL		BIT(31)
+#define P3D_RG_TX_IMPEL			GENMASK(28, 24)
+#define P3D_RG_TX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
+
+#define U3P_U3_PHYD_IMPCAL1		0x014
+#define P3D_RG_FORCE_RX_IMPEL		BIT(31)
+#define P3D_RG_RX_IMPEL			GENMASK(28, 24)
+#define P3D_RG_RX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
+
+#define U3P_U3_PHYD_RSV			0x054
+#define P3D_RG_EFUSE_AUTO_LOAD_DIS	BIT(12)
+
 #define U3P_U3_PHYD_CDR1		0x05c
 #define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
 #define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
@@ -307,6 +326,11 @@ struct mtk_phy_pdata {
 	 * 48M PLL, fix it by switching PLL to 26M from default 48M
 	 */
 	bool sw_pll_48m_to_26m;
+	/*
+	 * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
+	 * support sw way, also support it for v2/v3 optionally.
+	 */
+	bool sw_efuse_supported;
 	enum mtk_phy_version version;
 };
 
@@ -336,6 +360,10 @@ struct mtk_phy_instance {
 	struct regmap *type_sw;
 	u32 type_sw_reg;
 	u32 type_sw_index;
+	u32 efuse_sw_en;
+	u32 efuse_intr;
+	u32 efuse_tx_imp;
+	u32 efuse_rx_imp;
 	int eye_src;
 	int eye_vrt;
 	int eye_term;
@@ -1040,6 +1068,130 @@ static int phy_type_set(struct mtk_phy_instance *instance)
 	return 0;
 }
 
+static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance)
+{
+	struct device *dev = &instance->phy->dev;
+	int ret = 0;
+
+	/* tphy v1 doesn't support sw efuse, skip it */
+	if (!tphy->pdata->sw_efuse_supported) {
+		instance->efuse_sw_en = 0;
+		return 0;
+	}
+
+	/* software efuse is optional */
+	instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells");
+	if (!instance->efuse_sw_en)
+		return 0;
+
+	switch (instance->type) {
+	case PHY_TYPE_USB2:
+		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
+		if (ret) {
+			dev_err(dev, "fail to get u2 intr efuse, %d\n", ret);
+			break;
+		}
+
+		/* no efuse, ignore it */
+		if (!instance->efuse_intr) {
+			dev_warn(dev, "no u2 intr efuse, but dts enable it\n");
+			instance->efuse_sw_en = 0;
+			break;
+		}
+
+		dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr);
+		break;
+
+	case PHY_TYPE_USB3:
+	case PHY_TYPE_PCIE:
+		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
+		if (ret) {
+			dev_err(dev, "fail to get u3 intr efuse, %d\n", ret);
+			break;
+		}
+
+		ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp);
+		if (ret) {
+			dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret);
+			break;
+		}
+
+		ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp);
+		if (ret) {
+			dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret);
+			break;
+		}
+
+		/* no efuse, ignore it */
+		if (!instance->efuse_intr &&
+		    !instance->efuse_rx_imp &&
+		    !instance->efuse_rx_imp) {
+			dev_warn(dev, "no u3 intr efuse, but dts enable it\n");
+			instance->efuse_sw_en = 0;
+			break;
+		}
+
+		dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n",
+			instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp);
+		break;
+	default:
+		dev_err(dev, "no sw efuse for type %d\n", instance->type);
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static void phy_efuse_set(struct mtk_phy_instance *instance)
+{
+	struct device *dev = &instance->phy->dev;
+	struct u2phy_banks *u2_banks = &instance->u2_banks;
+	struct u3phy_banks *u3_banks = &instance->u3_banks;
+	u32 tmp;
+
+	if (!instance->efuse_sw_en)
+		return;
+
+	switch (instance->type) {
+	case PHY_TYPE_USB2:
+		tmp = readl(u2_banks->misc + U3P_MISC_REG1);
+		tmp |= MR1_EFUSE_AUTO_LOAD_DIS;
+		writel(tmp, u2_banks->misc + U3P_MISC_REG1);
+
+		tmp = readl(u2_banks->com + U3P_USBPHYACR1);
+		tmp &= ~PA1_RG_INTR_CAL;
+		tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr);
+		writel(tmp, u2_banks->com + U3P_USBPHYACR1);
+		break;
+	case PHY_TYPE_USB3:
+	case PHY_TYPE_PCIE:
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV);
+		tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV);
+
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
+		tmp &= ~P3D_RG_TX_IMPEL;
+		tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp);
+		tmp |= P3D_RG_FORCE_TX_IMPEL;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
+
+		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
+		tmp &= ~P3D_RG_RX_IMPEL;
+		tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp);
+		tmp |= P3D_RG_FORCE_RX_IMPEL;
+		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
+
+		tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
+		tmp &= ~P3A_RG_IEXT_INTR;
+		tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr);
+		writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0);
+		break;
+	default:
+		dev_warn(dev, "no sw efuse for type %d\n", instance->type);
+		break;
+	}
+}
+
 static int mtk_phy_init(struct phy *phy)
 {
 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
@@ -1050,6 +1202,8 @@ static int mtk_phy_init(struct phy *phy)
 	if (ret)
 		return ret;
 
+	phy_efuse_set(instance);
+
 	switch (instance->type) {
 	case PHY_TYPE_USB2:
 		u2_phy_instance_init(tphy, instance);
@@ -1134,6 +1288,7 @@ static struct phy *mtk_phy_xlate(struct device *dev,
 	struct mtk_phy_instance *instance = NULL;
 	struct device_node *phy_np = args->np;
 	int index;
+	int ret;
 
 	if (args->args_count != 1) {
 		dev_err(dev, "invalid number of cells in 'phy' property\n");
@@ -1174,6 +1329,10 @@ static struct phy *mtk_phy_xlate(struct device *dev,
 		return ERR_PTR(-EINVAL);
 	}
 
+	ret = phy_efuse_get(tphy, instance);
+	if (ret)
+		return ERR_PTR(ret);
+
 	phy_parse_property(tphy, instance);
 	phy_type_set(instance);
 
@@ -1196,10 +1355,12 @@ static const struct mtk_phy_pdata tphy_v1_pdata = {
 
 static const struct mtk_phy_pdata tphy_v2_pdata = {
 	.avoid_rx_sen_degradation = false,
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V2,
 };
 
 static const struct mtk_phy_pdata tphy_v3_pdata = {
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V3,
 };
 
@@ -1210,6 +1371,7 @@ static const struct mtk_phy_pdata mt8173_pdata = {
 
 static const struct mtk_phy_pdata mt8195_pdata = {
 	.sw_pll_48m_to_26m = true,
+	.sw_efuse_supported = true,
 	.version = MTK_PHY_V3,
 };
 
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 3/5] phy: mediatek: add helpers to update bits of registers

[Chunfeng Yun]

Add three helpers mtk_phy_clear/set/update_bits() for registers operation

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch, add register access helpers,
    Add updatel() macro suggested by Vinod, here add more ones instead.
---
 drivers/phy/mediatek/phy-mtk-io.h | 38 +++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 drivers/phy/mediatek/phy-mtk-io.h

diff --git a/drivers/phy/mediatek/phy-mtk-io.h b/drivers/phy/mediatek/phy-mtk-io.h
new file mode 100644
index 000000000000..500fcdab165d
--- /dev/null
+++ b/drivers/phy/mediatek/phy-mtk-io.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ *
+ * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
+ */
+
+#ifndef __PHY_MTK_H__
+#define __PHY_MTK_H__
+
+#include <linux/io.h>
+
+static inline void mtk_phy_clear_bits(void __iomem *reg, u32 bits)
+{
+	u32 tmp = readl(reg);
+
+	tmp &= ~bits;
+	writel(tmp, reg);
+}
+
+static inline void mtk_phy_set_bits(void __iomem *reg, u32 bits)
+{
+	u32 tmp = readl(reg);
+
+	tmp |= bits;
+	writel(tmp, reg);
+}
+
+static inline void mtk_phy_update_bits(void __iomem *reg, u32 mask, u32 val)
+{
+	u32 tmp = readl(reg);
+
+	tmp &= ~mask;
+	tmp |= val & mask;
+	writel(tmp, reg);
+}
+
+#endif
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 4/5] phy: phy-mtk-xsphy: use new io helpers to access register

[Chunfeng Yun]

Use new helpers mtk_phy_clear/set/update_bits() to access registers

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch
---
 drivers/phy/mediatek/phy-mtk-xsphy.c | 140 +++++++++------------------
 1 file changed, 46 insertions(+), 94 deletions(-)

diff --git a/drivers/phy/mediatek/phy-mtk-xsphy.c b/drivers/phy/mediatek/phy-mtk-xsphy.c
index 8c51131945c0..c0cdb78f77fa 100644
--- a/drivers/phy/mediatek/phy-mtk-xsphy.c
+++ b/drivers/phy/mediatek/phy-mtk-xsphy.c
@@ -10,13 +10,14 @@
 #include <dt-bindings/phy/phy.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 
+#include "phy-mtk-io.h"
+
 /* u2 phy banks */
 #define SSUSB_SIFSLV_MISC		0x000
 #define SSUSB_SIFSLV_U2FREQ		0x100
@@ -126,26 +127,18 @@ static void u2_phy_slew_rate_calibrate(struct mtk_xsphy *xsphy,
 		return;
 
 	/* enable USB ring oscillator */
-	tmp = readl(pbase + XSP_USBPHYACR5);
-	tmp |= P2A5_RG_HSTX_SRCAL_EN;
-	writel(tmp, pbase + XSP_USBPHYACR5);
+	mtk_phy_set_bits(pbase + XSP_USBPHYACR5, P2A5_RG_HSTX_SRCAL_EN);
 	udelay(1);	/* wait clock stable */
 
 	/* enable free run clock */
-	tmp = readl(pbase + XSP_U2FREQ_FMMONR1);
-	tmp |= P2F_RG_FRCK_EN;
-	writel(tmp, pbase + XSP_U2FREQ_FMMONR1);
+	mtk_phy_set_bits(pbase + XSP_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
 
 	/* set cycle count as 1024 */
-	tmp = readl(pbase + XSP_U2FREQ_FMCR0);
-	tmp &= ~(P2F_RG_CYCLECNT);
-	tmp |= P2F_RG_CYCLECNT_VAL(XSP_FM_DET_CYCLE_CNT);
-	writel(tmp, pbase + XSP_U2FREQ_FMCR0);
+	mtk_phy_update_bits(pbase + XSP_U2FREQ_FMCR0, P2F_RG_CYCLECNT,
+			    P2F_RG_CYCLECNT_VAL(XSP_FM_DET_CYCLE_CNT));
 
 	/* enable frequency meter */
-	tmp = readl(pbase + XSP_U2FREQ_FMCR0);
-	tmp |= P2F_RG_FREQDET_EN;
-	writel(tmp, pbase + XSP_U2FREQ_FMCR0);
+	mtk_phy_set_bits(pbase + XSP_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
 
 	/* ignore return value */
 	readl_poll_timeout(pbase + XSP_U2FREQ_FMMONR1, tmp,
@@ -154,14 +147,10 @@ static void u2_phy_slew_rate_calibrate(struct mtk_xsphy *xsphy,
 	fm_out = readl(pbase + XSP_U2FREQ_MMONR0);
 
 	/* disable frequency meter */
-	tmp = readl(pbase + XSP_U2FREQ_FMCR0);
-	tmp &= ~P2F_RG_FREQDET_EN;
-	writel(tmp, pbase + XSP_U2FREQ_FMCR0);
+	mtk_phy_clear_bits(pbase + XSP_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
 
 	/* disable free run clock */
-	tmp = readl(pbase + XSP_U2FREQ_FMMONR1);
-	tmp &= ~P2F_RG_FRCK_EN;
-	writel(tmp, pbase + XSP_U2FREQ_FMMONR1);
+	mtk_phy_clear_bits(pbase + XSP_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
 
 	if (fm_out) {
 		/* (1024 / FM_OUT) x reference clock frequency x coefficient */
@@ -177,31 +166,22 @@ static void u2_phy_slew_rate_calibrate(struct mtk_xsphy *xsphy,
 		xsphy->src_ref_clk, xsphy->src_coef);
 
 	/* set HS slew rate */
-	tmp = readl(pbase + XSP_USBPHYACR5);
-	tmp &= ~P2A5_RG_HSTX_SRCTRL;
-	tmp |= P2A5_RG_HSTX_SRCTRL_VAL(calib_val);
-	writel(tmp, pbase + XSP_USBPHYACR5);
+	mtk_phy_update_bits(pbase + XSP_USBPHYACR5, P2A5_RG_HSTX_SRCTRL,
+			    P2A5_RG_HSTX_SRCTRL_VAL(calib_val));
 
 	/* disable USB ring oscillator */
-	tmp = readl(pbase + XSP_USBPHYACR5);
-	tmp &= ~P2A5_RG_HSTX_SRCAL_EN;
-	writel(tmp, pbase + XSP_USBPHYACR5);
+	mtk_phy_clear_bits(pbase + XSP_USBPHYACR5, P2A5_RG_HSTX_SRCAL_EN);
 }
 
 static void u2_phy_instance_init(struct mtk_xsphy *xsphy,
 				 struct xsphy_instance *inst)
 {
 	void __iomem *pbase = inst->port_base;
-	u32 tmp;
 
 	/* DP/DM BC1.1 path Disable */
-	tmp = readl(pbase + XSP_USBPHYACR6);
-	tmp &= ~P2A6_RG_BC11_SW_EN;
-	writel(tmp, pbase + XSP_USBPHYACR6);
+	mtk_phy_clear_bits(pbase + XSP_USBPHYACR6, P2A6_RG_BC11_SW_EN);
 
-	tmp = readl(pbase + XSP_USBPHYACR0);
-	tmp |= P2A0_RG_INTR_EN;
-	writel(tmp, pbase + XSP_USBPHYACR0);
+	mtk_phy_set_bits(pbase + XSP_USBPHYACR0, P2A0_RG_INTR_EN);
 }
 
 static void u2_phy_instance_power_on(struct mtk_xsphy *xsphy,
@@ -209,16 +189,12 @@ static void u2_phy_instance_power_on(struct mtk_xsphy *xsphy,
 {
 	void __iomem *pbase = inst->port_base;
 	u32 index = inst->index;
-	u32 tmp;
 
-	tmp = readl(pbase + XSP_USBPHYACR6);
-	tmp |= P2A6_RG_OTG_VBUSCMP_EN;
-	writel(tmp, pbase + XSP_USBPHYACR6);
+	mtk_phy_set_bits(pbase + XSP_USBPHYACR6, P2A6_RG_OTG_VBUSCMP_EN);
 
-	tmp = readl(pbase + XSP_U2PHYDTM1);
-	tmp |= P2D_RG_VBUSVALID | P2D_RG_AVALID;
-	tmp &= ~P2D_RG_SESSEND;
-	writel(tmp, pbase + XSP_U2PHYDTM1);
+	mtk_phy_update_bits(pbase + XSP_U2PHYDTM1,
+			    P2D_RG_VBUSVALID | P2D_RG_AVALID | P2D_RG_SESSEND,
+			    P2D_RG_VBUSVALID | P2D_RG_AVALID);
 
 	dev_dbg(xsphy->dev, "%s(%d)\n", __func__, index);
 }
@@ -228,16 +204,12 @@ static void u2_phy_instance_power_off(struct mtk_xsphy *xsphy,
 {
 	void __iomem *pbase = inst->port_base;
 	u32 index = inst->index;
-	u32 tmp;
 
-	tmp = readl(pbase + XSP_USBPHYACR6);
-	tmp &= ~P2A6_RG_OTG_VBUSCMP_EN;
-	writel(tmp, pbase + XSP_USBPHYACR6);
+	mtk_phy_clear_bits(pbase + XSP_USBPHYACR6, P2A6_RG_OTG_VBUSCMP_EN);
 
-	tmp = readl(pbase + XSP_U2PHYDTM1);
-	tmp &= ~(P2D_RG_VBUSVALID | P2D_RG_AVALID);
-	tmp |= P2D_RG_SESSEND;
-	writel(tmp, pbase + XSP_U2PHYDTM1);
+	mtk_phy_update_bits(pbase + XSP_U2PHYDTM1,
+			    P2D_RG_VBUSVALID | P2D_RG_AVALID | P2D_RG_SESSEND,
+			    P2D_RG_SESSEND);
 
 	dev_dbg(xsphy->dev, "%s(%d)\n", __func__, index);
 }
@@ -306,63 +278,43 @@ static void u2_phy_props_set(struct mtk_xsphy *xsphy,
 			     struct xsphy_instance *inst)
 {
 	void __iomem *pbase = inst->port_base;
-	u32 tmp;
 
-	if (inst->efuse_intr) {
-		tmp = readl(pbase + XSP_USBPHYACR1);
-		tmp &= ~P2A1_RG_INTR_CAL;
-		tmp |= P2A1_RG_INTR_CAL_VAL(inst->efuse_intr);
-		writel(tmp, pbase + XSP_USBPHYACR1);
-	}
+	if (inst->efuse_intr)
+		mtk_phy_update_bits(pbase + XSP_USBPHYACR1, P2A1_RG_INTR_CAL,
+				    P2A1_RG_INTR_CAL_VAL(inst->efuse_intr));
 
-	if (inst->eye_src) {
-		tmp = readl(pbase + XSP_USBPHYACR5);
-		tmp &= ~P2A5_RG_HSTX_SRCTRL;
-		tmp |= P2A5_RG_HSTX_SRCTRL_VAL(inst->eye_src);
-		writel(tmp, pbase + XSP_USBPHYACR5);
-	}
+	if (inst->eye_src)
+		mtk_phy_update_bits(pbase + XSP_USBPHYACR5, P2A5_RG_HSTX_SRCTRL,
+				    P2A5_RG_HSTX_SRCTRL_VAL(inst->eye_src));
 
-	if (inst->eye_vrt) {
-		tmp = readl(pbase + XSP_USBPHYACR1);
-		tmp &= ~P2A1_RG_VRT_SEL;
-		tmp |= P2A1_RG_VRT_SEL_VAL(inst->eye_vrt);
-		writel(tmp, pbase + XSP_USBPHYACR1);
-	}
+	if (inst->eye_vrt)
+		mtk_phy_update_bits(pbase + XSP_USBPHYACR1, P2A1_RG_VRT_SEL,
+				    P2A1_RG_VRT_SEL_VAL(inst->eye_vrt));
 
-	if (inst->eye_term) {
-		tmp = readl(pbase + XSP_USBPHYACR1);
-		tmp &= ~P2A1_RG_TERM_SEL;
-		tmp |= P2A1_RG_TERM_SEL_VAL(inst->eye_term);
-		writel(tmp, pbase + XSP_USBPHYACR1);
-	}
+	if (inst->eye_term)
+		mtk_phy_update_bits(pbase + XSP_USBPHYACR1, P2A1_RG_TERM_SEL,
+				    P2A1_RG_TERM_SEL_VAL(inst->eye_term));
 }
 
 static void u3_phy_props_set(struct mtk_xsphy *xsphy,
 			     struct xsphy_instance *inst)
 {
 	void __iomem *pbase = inst->port_base;
-	u32 tmp;
 
-	if (inst->efuse_intr) {
-		tmp = readl(xsphy->glb_base + SSPXTP_PHYA_GLB_00);
-		tmp &= ~RG_XTP_GLB_BIAS_INTR_CTRL;
-		tmp |= RG_XTP_GLB_BIAS_INTR_CTRL_VAL(inst->efuse_intr);
-		writel(tmp, xsphy->glb_base + SSPXTP_PHYA_GLB_00);
-	}
+	if (inst->efuse_intr)
+		mtk_phy_update_bits(xsphy->glb_base + SSPXTP_PHYA_GLB_00,
+				    RG_XTP_GLB_BIAS_INTR_CTRL,
+				    RG_XTP_GLB_BIAS_INTR_CTRL_VAL(inst->efuse_intr));
 
-	if (inst->efuse_tx_imp) {
-		tmp = readl(pbase + SSPXTP_PHYA_LN_04);
-		tmp &= ~RG_XTP_LN0_TX_IMPSEL;
-		tmp |= RG_XTP_LN0_TX_IMPSEL_VAL(inst->efuse_tx_imp);
-		writel(tmp, pbase + SSPXTP_PHYA_LN_04);
-	}
+	if (inst->efuse_tx_imp)
+		mtk_phy_update_bits(pbase + SSPXTP_PHYA_LN_04,
+				    RG_XTP_LN0_TX_IMPSEL,
+				    RG_XTP_LN0_TX_IMPSEL_VAL(inst->efuse_tx_imp));
 
-	if (inst->efuse_rx_imp) {
-		tmp = readl(pbase + SSPXTP_PHYA_LN_14);
-		tmp &= ~RG_XTP_LN0_RX_IMPSEL;
-		tmp |= RG_XTP_LN0_RX_IMPSEL_VAL(inst->efuse_rx_imp);
-		writel(tmp, pbase + SSPXTP_PHYA_LN_14);
-	}
+	if (inst->efuse_rx_imp)
+		mtk_phy_update_bits(pbase + SSPXTP_PHYA_LN_14,
+				    RG_XTP_LN0_RX_IMPSEL,
+				    RG_XTP_LN0_RX_IMPSEL_VAL(inst->efuse_rx_imp));
 }
 
 static int mtk_phy_init(struct phy *phy)
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 5/5] phy: phy-mtk-tphy: use new io helpers to access register

[Chunfeng Yun]

Use new helpers mtk_phy_clear/set/update_bits() to access registers

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch
---
 drivers/phy/mediatek/phy-mtk-tphy.c | 504 ++++++++++------------------
 1 file changed, 179 insertions(+), 325 deletions(-)

diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
index 98a942c607a6..6d307102f4f6 100644
--- a/drivers/phy/mediatek/phy-mtk-tphy.c
+++ b/drivers/phy/mediatek/phy-mtk-tphy.c
@@ -8,7 +8,6 @@
 #include <dt-bindings/phy/phy.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/io.h>
 #include <linux/iopoll.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
@@ -19,6 +18,8 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 
+#include "phy-mtk-io.h"
+
 /* version V1 sub-banks offset base address */
 /* banks shared by multiple phys */
 #define SSUSB_SIFSLV_V1_SPLLC		0x000	/* shared by u3 phys */
@@ -401,15 +402,11 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
 		return;
 
 	/* enable USB ring oscillator */
-	tmp = readl(com + U3P_USBPHYACR5);
-	tmp |= PA5_RG_U2_HSTX_SRCAL_EN;
-	writel(tmp, com + U3P_USBPHYACR5);
+	mtk_phy_set_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
 	udelay(1);
 
 	/*enable free run clock */
-	tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
-	tmp |= P2F_RG_FRCK_EN;
-	writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
+	mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
 
 	/* set cycle count as 1024, and select u2 channel */
 	tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
@@ -421,9 +418,7 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
 	writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
 
 	/* enable frequency meter */
-	tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
-	tmp |= P2F_RG_FREQDET_EN;
-	writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
+	mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
 
 	/* ignore return value */
 	readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp,
@@ -432,14 +427,10 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
 	fm_out = readl(fmreg + U3P_U2FREQ_VALUE);
 
 	/* disable frequency meter */
-	tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
-	tmp &= ~P2F_RG_FREQDET_EN;
-	writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
+	mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
 
 	/*disable free run clock */
-	tmp = readl(fmreg + U3P_U2FREQ_FMMONR1);
-	tmp &= ~P2F_RG_FRCK_EN;
-	writel(tmp, fmreg + U3P_U2FREQ_FMMONR1);
+	mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
 
 	if (fm_out) {
 		/* ( 1024 / FM_OUT ) x reference clock frequency x coef */
@@ -455,63 +446,44 @@ static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
 		tphy->src_ref_clk, tphy->src_coef);
 
 	/* set HS slew rate */
-	tmp = readl(com + U3P_USBPHYACR5);
-	tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
-	tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(calibration_val);
-	writel(tmp, com + U3P_USBPHYACR5);
+	mtk_phy_update_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
+			    PA5_RG_U2_HSTX_SRCTRL_VAL(calibration_val));
 
 	/* disable USB ring oscillator */
-	tmp = readl(com + U3P_USBPHYACR5);
-	tmp &= ~PA5_RG_U2_HSTX_SRCAL_EN;
-	writel(tmp, com + U3P_USBPHYACR5);
+	mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
 }
 
 static void u3_phy_instance_init(struct mtk_tphy *tphy,
 	struct mtk_phy_instance *instance)
 {
 	struct u3phy_banks *u3_banks = &instance->u3_banks;
-	u32 tmp;
 
 	/* gating PCIe Analog XTAL clock */
-	tmp = readl(u3_banks->spllc + U3P_SPLLC_XTALCTL3);
-	tmp |= XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD;
-	writel(tmp, u3_banks->spllc + U3P_SPLLC_XTALCTL3);
+	mtk_phy_set_bits(u3_banks->spllc + U3P_SPLLC_XTALCTL3,
+			 XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD);
 
 	/* gating XSQ */
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
-	tmp &= ~P3A_RG_XTAL_EXT_EN_U3;
-	tmp |= P3A_RG_XTAL_EXT_EN_U3_VAL(2);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG0);
-
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG9);
-	tmp &= ~P3A_RG_RX_DAC_MUX;
-	tmp |= P3A_RG_RX_DAC_MUX_VAL(4);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG9);
-
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG6);
-	tmp &= ~P3A_RG_TX_EIDLE_CM;
-	tmp |= P3A_RG_TX_EIDLE_CM_VAL(0xe);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG6);
-
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_CDR1);
-	tmp &= ~(P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1);
-	tmp |= P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_CDR1);
-
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_LFPS1);
-	tmp &= ~P3D_RG_FWAKE_TH;
-	tmp |= P3D_RG_FWAKE_TH_VAL(0x34);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_LFPS1);
-
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET1);
-	tmp &= ~P3D_RG_RXDET_STB2_SET;
-	tmp |= P3D_RG_RXDET_STB2_SET_VAL(0x10);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET1);
-
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET2);
-	tmp &= ~P3D_RG_RXDET_STB2_SET_P3;
-	tmp |= P3D_RG_RXDET_STB2_SET_P3_VAL(0x10);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET2);
+	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_DA_REG0,
+			    P3A_RG_XTAL_EXT_EN_U3, P3A_RG_XTAL_EXT_EN_U3_VAL(2));
+
+	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG9,
+			    P3A_RG_RX_DAC_MUX, P3A_RG_RX_DAC_MUX_VAL(4));
+
+	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG6,
+			    P3A_RG_TX_EIDLE_CM, P3A_RG_TX_EIDLE_CM_VAL(0xe));
+
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_CDR1,
+			    P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1,
+			    P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3));
+
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_LFPS1,
+			    P3D_RG_FWAKE_TH, P3D_RG_FWAKE_TH_VAL(0x34));
+
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET1,
+			    P3D_RG_RXDET_STB2_SET, P3D_RG_RXDET_STB2_SET_VAL(0x10));
+
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET2,
+			    P3D_RG_RXDET_STB2_SET_P3, P3D_RG_RXDET_STB2_SET_P3_VAL(0x10));
 
 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
 }
@@ -521,26 +493,20 @@ static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
 {
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
-	u32 tmp;
 
 	if (!tphy->pdata->sw_pll_48m_to_26m)
 		return;
 
-	tmp = readl(com + U3P_USBPHYACR0);
-	tmp &= ~PA0_USB20_PLL_PREDIV;
-	tmp |= PA0_USB20_PLL_PREDIV_VAL(0);
-	writel(tmp, com + U3P_USBPHYACR0);
+	mtk_phy_update_bits(com + U3P_USBPHYACR0, PA0_USB20_PLL_PREDIV,
+			    PA0_USB20_PLL_PREDIV_VAL(0));
 
-	tmp = readl(com + U3P_USBPHYACR2);
-	tmp &= ~PA2_RG_U2PLL_BW;
-	tmp |= PA2_RG_U2PLL_BW_VAL(3);
-	writel(tmp, com + U3P_USBPHYACR2);
+	mtk_phy_update_bits(com + U3P_USBPHYACR2, PA2_RG_U2PLL_BW,
+			    PA2_RG_U2PLL_BW_VAL(3));
 
 	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
 
-	tmp = readl(com + U3P_U2PHYA_RESV1);
-	tmp |= P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL;
-	writel(tmp, com + U3P_U2PHYA_RESV1);
+	mtk_phy_set_bits(com + U3P_U2PHYA_RESV1,
+			 P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL);
 }
 
 static void u2_phy_instance_init(struct mtk_tphy *tphy,
@@ -549,58 +515,40 @@ static void u2_phy_instance_init(struct mtk_tphy *tphy,
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
 	u32 index = instance->index;
-	u32 tmp;
 
 	/* switch to USB function, and enable usb pll */
-	tmp = readl(com + U3P_U2PHYDTM0);
-	tmp &= ~(P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM);
-	tmp |= P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0);
-	writel(tmp, com + U3P_U2PHYDTM0);
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM);
+
+	mtk_phy_update_bits(com + U3P_U2PHYDTM0, P2C_RG_XCVRSEL | P2C_RG_DATAIN,
+			    P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0));
 
-	tmp = readl(com + U3P_U2PHYDTM1);
-	tmp &= ~P2C_RG_UART_EN;
-	writel(tmp, com + U3P_U2PHYDTM1);
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_UART_EN);
 
-	tmp = readl(com + U3P_USBPHYACR0);
-	tmp |= PA0_RG_USB20_INTR_EN;
-	writel(tmp, com + U3P_USBPHYACR0);
+	mtk_phy_set_bits(com + U3P_USBPHYACR0, PA0_RG_USB20_INTR_EN);
 
 	/* disable switch 100uA current to SSUSB */
-	tmp = readl(com + U3P_USBPHYACR5);
-	tmp &= ~PA5_RG_U2_HS_100U_U3_EN;
-	writel(tmp, com + U3P_USBPHYACR5);
-
-	if (!index) {
-		tmp = readl(com + U3P_U2PHYACR4);
-		tmp &= ~P2C_U2_GPIO_CTR_MSK;
-		writel(tmp, com + U3P_U2PHYACR4);
-	}
+	mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN);
+
+	if (!index)
+		mtk_phy_clear_bits(com + U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK);
 
 	if (tphy->pdata->avoid_rx_sen_degradation) {
 		if (!index) {
-			tmp = readl(com + U3P_USBPHYACR2);
-			tmp |= PA2_RG_SIF_U2PLL_FORCE_EN;
-			writel(tmp, com + U3P_USBPHYACR2);
+			mtk_phy_set_bits(com + U3P_USBPHYACR2, PA2_RG_SIF_U2PLL_FORCE_EN);
 
-			tmp = readl(com + U3D_U2PHYDCR0);
-			tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
-			writel(tmp, com + U3D_U2PHYDCR0);
+			mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
 		} else {
-			tmp = readl(com + U3D_U2PHYDCR0);
-			tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
-			writel(tmp, com + U3D_U2PHYDCR0);
+			mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
 
-			tmp = readl(com + U3P_U2PHYDTM0);
-			tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
-			writel(tmp, com + U3P_U2PHYDTM0);
+			mtk_phy_set_bits(com + U3P_U2PHYDTM0,
+					 P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
 		}
 	}
 
-	tmp = readl(com + U3P_USBPHYACR6);
-	tmp &= ~PA6_RG_U2_BC11_SW_EN;	/* DP/DM BC1.1 path Disable */
-	tmp &= ~PA6_RG_U2_SQTH;
-	tmp |= PA6_RG_U2_SQTH_VAL(2);
-	writel(tmp, com + U3P_USBPHYACR6);
+	/* DP/DM BC1.1 path Disable */
+	mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN);
+
+	mtk_phy_update_bits(com + U3P_USBPHYACR6, PA6_RG_U2_SQTH, PA6_RG_U2_SQTH_VAL(2));
 
 	/* Workaround only for mt8195, HW fix it for others (V3) */
 	u2_phy_pll_26m_set(tphy, instance);
@@ -614,30 +562,21 @@ static void u2_phy_instance_power_on(struct mtk_tphy *tphy,
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
 	u32 index = instance->index;
-	u32 tmp;
 
-	tmp = readl(com + U3P_U2PHYDTM0);
-	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
-	writel(tmp, com + U3P_U2PHYDTM0);
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM0,
+			   P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
 
 	/* OTG Enable */
-	tmp = readl(com + U3P_USBPHYACR6);
-	tmp |= PA6_RG_U2_OTG_VBUSCMP_EN;
-	writel(tmp, com + U3P_USBPHYACR6);
+	mtk_phy_set_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
+
+	mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
 
-	tmp = readl(com + U3P_U2PHYDTM1);
-	tmp |= P2C_RG_VBUSVALID | P2C_RG_AVALID;
-	tmp &= ~P2C_RG_SESSEND;
-	writel(tmp, com + U3P_U2PHYDTM1);
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);
 
 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
-		tmp = readl(com + U3D_U2PHYDCR0);
-		tmp |= P2C_RG_SIF_U2PLL_FORCE_ON;
-		writel(tmp, com + U3D_U2PHYDCR0);
+		mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
 
-		tmp = readl(com + U3P_U2PHYDTM0);
-		tmp |= P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM;
-		writel(tmp, com + U3P_U2PHYDTM0);
+		mtk_phy_set_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
 	}
 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
 }
@@ -648,30 +587,20 @@ static void u2_phy_instance_power_off(struct mtk_tphy *tphy,
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
 	u32 index = instance->index;
-	u32 tmp;
 
-	tmp = readl(com + U3P_U2PHYDTM0);
-	tmp &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN);
-	writel(tmp, com + U3P_U2PHYDTM0);
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_XCVRSEL | P2C_RG_DATAIN);
 
 	/* OTG Disable */
-	tmp = readl(com + U3P_USBPHYACR6);
-	tmp &= ~PA6_RG_U2_OTG_VBUSCMP_EN;
-	writel(tmp, com + U3P_USBPHYACR6);
+	mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
+
+	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
 
-	tmp = readl(com + U3P_U2PHYDTM1);
-	tmp &= ~(P2C_RG_VBUSVALID | P2C_RG_AVALID);
-	tmp |= P2C_RG_SESSEND;
-	writel(tmp, com + U3P_U2PHYDTM1);
+	mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);
 
 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
-		tmp = readl(com + U3P_U2PHYDTM0);
-		tmp &= ~(P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
-		writel(tmp, com + U3P_U2PHYDTM0);
+		mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
 
-		tmp = readl(com + U3D_U2PHYDCR0);
-		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
-		writel(tmp, com + U3D_U2PHYDCR0);
+		mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
 	}
 
 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
@@ -683,16 +612,11 @@ static void u2_phy_instance_exit(struct mtk_tphy *tphy,
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
 	u32 index = instance->index;
-	u32 tmp;
 
 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
-		tmp = readl(com + U3D_U2PHYDCR0);
-		tmp &= ~P2C_RG_SIF_U2PLL_FORCE_ON;
-		writel(tmp, com + U3D_U2PHYDCR0);
+		mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
 
-		tmp = readl(com + U3P_U2PHYDTM0);
-		tmp &= ~P2C_FORCE_SUSPENDM;
-		writel(tmp, com + U3P_U2PHYDTM0);
+		mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM);
 	}
 }
 
@@ -725,69 +649,50 @@ static void pcie_phy_instance_init(struct mtk_tphy *tphy,
 	struct mtk_phy_instance *instance)
 {
 	struct u3phy_banks *u3_banks = &instance->u3_banks;
-	u32 tmp;
+	void __iomem *phya = u3_banks->phya;
 
 	if (tphy->pdata->version != MTK_PHY_V1)
 		return;
 
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG0);
-	tmp &= ~(P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H);
-	tmp |= P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG0);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG0,
+			    P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H,
+			    P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2));
 
 	/* ref clk drive */
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG1);
-	tmp &= ~P3A_RG_CLKDRV_AMP;
-	tmp |= P3A_RG_CLKDRV_AMP_VAL(0x4);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG1);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_REG1, P3A_RG_CLKDRV_AMP,
+			    P3A_RG_CLKDRV_AMP_VAL(0x4));
 
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
-	tmp &= ~P3A_RG_CLKDRV_OFF;
-	tmp |= P3A_RG_CLKDRV_OFF_VAL(0x1);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_REG0, P3A_RG_CLKDRV_OFF,
+			    P3A_RG_CLKDRV_OFF_VAL(0x1));
 
 	/* SSC delta -5000ppm */
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG20);
-	tmp &= ~P3A_RG_PLL_DELTA1_PE2H;
-	tmp |= P3A_RG_PLL_DELTA1_PE2H_VAL(0x3c);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG20);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG20, P3A_RG_PLL_DELTA1_PE2H,
+			    P3A_RG_PLL_DELTA1_PE2H_VAL(0x3c));
 
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG25);
-	tmp &= ~P3A_RG_PLL_DELTA_PE2H;
-	tmp |= P3A_RG_PLL_DELTA_PE2H_VAL(0x36);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG25);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG25, P3A_RG_PLL_DELTA_PE2H,
+			    P3A_RG_PLL_DELTA_PE2H_VAL(0x36));
 
 	/* change pll BW 0.6M */
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG5);
-	tmp &= ~(P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H);
-	tmp |= P3A_RG_PLL_BR_PE2H_VAL(0x1) | P3A_RG_PLL_IC_PE2H_VAL(0x1);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG5);
-
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG4);
-	tmp &= ~(P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H);
-	tmp |= P3A_RG_PLL_BC_PE2H_VAL(0x3);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG4);
-
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG6);
-	tmp &= ~P3A_RG_PLL_IR_PE2H;
-	tmp |= P3A_RG_PLL_IR_PE2H_VAL(0x2);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG6);
-
-	tmp = readl(u3_banks->phya + U3P_U3_PHYA_DA_REG7);
-	tmp &= ~P3A_RG_PLL_BP_PE2H;
-	tmp |= P3A_RG_PLL_BP_PE2H_VAL(0xa);
-	writel(tmp, u3_banks->phya + U3P_U3_PHYA_DA_REG7);
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG5,
+			    P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H,
+			    P3A_RG_PLL_BR_PE2H_VAL(0x1) | P3A_RG_PLL_IC_PE2H_VAL(0x1));
+
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG4,
+			    P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H,
+			    P3A_RG_PLL_BC_PE2H_VAL(0x3));
+
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG6, P3A_RG_PLL_IR_PE2H,
+			    P3A_RG_PLL_IR_PE2H_VAL(0x2));
+
+	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG7, P3A_RG_PLL_BP_PE2H,
+			    P3A_RG_PLL_BP_PE2H_VAL(0xa));
 
 	/* Tx Detect Rx Timing: 10us -> 5us */
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET1);
-	tmp &= ~P3D_RG_RXDET_STB2_SET;
-	tmp |= P3D_RG_RXDET_STB2_SET_VAL(0x10);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET1);
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET1,
+			    P3D_RG_RXDET_STB2_SET, P3D_RG_RXDET_STB2_SET_VAL(0x10));
 
-	tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RXDET2);
-	tmp &= ~P3D_RG_RXDET_STB2_SET_P3;
-	tmp |= P3D_RG_RXDET_STB2_SET_P3_VAL(0x10);
-	writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RXDET2);
+	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET2,
+			    P3D_RG_RXDET_STB2_SET_P3, P3D_RG_RXDET_STB2_SET_P3_VAL(0x10));
 
 	/* wait for PCIe subsys register to active */
 	usleep_range(2500, 3000);
@@ -798,15 +703,12 @@ static void pcie_phy_instance_power_on(struct mtk_tphy *tphy,
 	struct mtk_phy_instance *instance)
 {
 	struct u3phy_banks *bank = &instance->u3_banks;
-	u32 tmp;
 
-	tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLD);
-	tmp &= ~(P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
-	writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLD);
+	mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
+			   P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
 
-	tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLE);
-	tmp &= ~(P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
-	writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLE);
+	mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
+			   P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
 }
 
 static void pcie_phy_instance_power_off(struct mtk_tphy *tphy,
@@ -814,15 +716,12 @@ static void pcie_phy_instance_power_off(struct mtk_tphy *tphy,
 
 {
 	struct u3phy_banks *bank = &instance->u3_banks;
-	u32 tmp;
 
-	tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLD);
-	tmp |= P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST;
-	writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLD);
+	mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
+			 P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
 
-	tmp = readl(bank->chip + U3P_U3_CHIP_GPIO_CTLE);
-	tmp |= P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD;
-	writel(tmp, bank->chip + U3P_U3_CHIP_GPIO_CTLE);
+	mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
+			 P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
 }
 
 static void sata_phy_instance_init(struct mtk_tphy *tphy,
@@ -830,55 +729,42 @@ static void sata_phy_instance_init(struct mtk_tphy *tphy,
 {
 	struct u3phy_banks *u3_banks = &instance->u3_banks;
 	void __iomem *phyd = u3_banks->phyd;
-	u32 tmp;
 
 	/* charge current adjustment */
-	tmp = readl(phyd + ANA_RG_CTRL_SIGNAL6);
-	tmp &= ~(RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK);
-	tmp |= RG_CDR_BIRLTR_GEN1_VAL(0x6) | RG_CDR_BC_GEN1_VAL(0x1a);
-	writel(tmp, phyd + ANA_RG_CTRL_SIGNAL6);
-
-	tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL4);
-	tmp &= ~RG_CDR_BIRLTD0_GEN1_MSK;
-	tmp |= RG_CDR_BIRLTD0_GEN1_VAL(0x18);
-	writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL4);
-
-	tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL5);
-	tmp &= ~RG_CDR_BIRLTD0_GEN3_MSK;
-	tmp |= RG_CDR_BIRLTD0_GEN3_VAL(0x06);
-	writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL5);
-
-	tmp = readl(phyd + ANA_RG_CTRL_SIGNAL4);
-	tmp &= ~(RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK);
-	tmp |= RG_CDR_BICLTR_GEN1_VAL(0x0c) | RG_CDR_BR_GEN2_VAL(0x07);
-	writel(tmp, phyd + ANA_RG_CTRL_SIGNAL4);
-
-	tmp = readl(phyd + PHYD_CTRL_SIGNAL_MODE4);
-	tmp &= ~(RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK);
-	tmp |= RG_CDR_BICLTD0_GEN1_VAL(0x08) | RG_CDR_BICLTD1_GEN1_VAL(0x02);
-	writel(tmp, phyd + PHYD_CTRL_SIGNAL_MODE4);
-
-	tmp = readl(phyd + PHYD_DESIGN_OPTION2);
-	tmp &= ~RG_LOCK_CNT_SEL_MSK;
-	tmp |= RG_LOCK_CNT_SEL_VAL(0x02);
-	writel(tmp, phyd + PHYD_DESIGN_OPTION2);
-
-	tmp = readl(phyd + PHYD_DESIGN_OPTION9);
-	tmp &= ~(RG_T2_MIN_MSK | RG_TG_MIN_MSK |
-		 RG_T2_MAX_MSK | RG_TG_MAX_MSK);
-	tmp |= RG_T2_MIN_VAL(0x12) | RG_TG_MIN_VAL(0x04) |
-	       RG_T2_MAX_VAL(0x31) | RG_TG_MAX_VAL(0x0e);
-	writel(tmp, phyd + PHYD_DESIGN_OPTION9);
-
-	tmp = readl(phyd + ANA_RG_CTRL_SIGNAL1);
-	tmp &= ~RG_IDRV_0DB_GEN1_MSK;
-	tmp |= RG_IDRV_0DB_GEN1_VAL(0x20);
-	writel(tmp, phyd + ANA_RG_CTRL_SIGNAL1);
-
-	tmp = readl(phyd + ANA_EQ_EYE_CTRL_SIGNAL1);
-	tmp &= ~RG_EQ_DLEQ_LFI_GEN1_MSK;
-	tmp |= RG_EQ_DLEQ_LFI_GEN1_VAL(0x03);
-	writel(tmp, phyd + ANA_EQ_EYE_CTRL_SIGNAL1);
+	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL6,
+			    RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK,
+			    RG_CDR_BIRLTR_GEN1_VAL(0x6) | RG_CDR_BC_GEN1_VAL(0x1a));
+
+	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL4, RG_CDR_BIRLTD0_GEN1_MSK,
+			    RG_CDR_BIRLTD0_GEN1_VAL(0x18));
+
+	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL5, RG_CDR_BIRLTD0_GEN3_MSK,
+			    RG_CDR_BIRLTD0_GEN3_VAL(0x06));
+
+	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL4,
+			    RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK,
+			    RG_CDR_BICLTR_GEN1_VAL(0x0c) | RG_CDR_BR_GEN2_VAL(0x07));
+
+	mtk_phy_update_bits(phyd + PHYD_CTRL_SIGNAL_MODE4,
+			    RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK,
+			    RG_CDR_BICLTD0_GEN1_VAL(0x08) | RG_CDR_BICLTD1_GEN1_VAL(0x02));
+
+	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION2, RG_LOCK_CNT_SEL_MSK,
+			    RG_LOCK_CNT_SEL_VAL(0x02));
+
+	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
+			    RG_T2_MIN_MSK | RG_TG_MIN_MSK,
+			    RG_T2_MIN_VAL(0x12) | RG_TG_MIN_VAL(0x04));
+
+	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
+			    RG_T2_MAX_MSK | RG_TG_MAX_MSK,
+			    RG_T2_MAX_VAL(0x31) | RG_TG_MAX_VAL(0x0e));
+
+	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL1, RG_IDRV_0DB_GEN1_MSK,
+			    RG_IDRV_0DB_GEN1_VAL(0x20));
+
+	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL1, RG_EQ_DLEQ_LFI_GEN1_MSK,
+			    RG_EQ_DLEQ_LFI_GEN1_VAL(0x03));
 
 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
 }
@@ -966,48 +852,29 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
 {
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	void __iomem *com = u2_banks->com;
-	u32 tmp;
 
-	if (instance->bc12_en) {
-		tmp = readl(com + U3P_U2PHYBC12C);
-		tmp |= P2C_RG_CHGDT_EN;	/* BC1.2 path Enable */
-		writel(tmp, com + U3P_U2PHYBC12C);
-	}
+	if (instance->bc12_en) /* BC1.2 path Enable */
+		mtk_phy_set_bits(com + U3P_U2PHYBC12C, P2C_RG_CHGDT_EN);
 
-	if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src) {
-		tmp = readl(com + U3P_USBPHYACR5);
-		tmp &= ~PA5_RG_U2_HSTX_SRCTRL;
-		tmp |= PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src);
-		writel(tmp, com + U3P_USBPHYACR5);
-	}
+	if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src)
+		mtk_phy_update_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
+				    PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src));
 
-	if (instance->eye_vrt) {
-		tmp = readl(com + U3P_USBPHYACR1);
-		tmp &= ~PA1_RG_VRT_SEL;
-		tmp |= PA1_RG_VRT_SEL_VAL(instance->eye_vrt);
-		writel(tmp, com + U3P_USBPHYACR1);
-	}
+	if (instance->eye_vrt)
+		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL,
+				    PA1_RG_VRT_SEL_VAL(instance->eye_vrt));
 
-	if (instance->eye_term) {
-		tmp = readl(com + U3P_USBPHYACR1);
-		tmp &= ~PA1_RG_TERM_SEL;
-		tmp |= PA1_RG_TERM_SEL_VAL(instance->eye_term);
-		writel(tmp, com + U3P_USBPHYACR1);
-	}
+	if (instance->eye_term)
+		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL,
+				    PA1_RG_TERM_SEL_VAL(instance->eye_term));
 
-	if (instance->intr) {
-		tmp = readl(com + U3P_USBPHYACR1);
-		tmp &= ~PA1_RG_INTR_CAL;
-		tmp |= PA1_RG_INTR_CAL_VAL(instance->intr);
-		writel(tmp, com + U3P_USBPHYACR1);
-	}
+	if (instance->intr)
+		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
+				    PA1_RG_INTR_CAL_VAL(instance->intr));
 
-	if (instance->discth) {
-		tmp = readl(com + U3P_USBPHYACR6);
-		tmp &= ~PA6_RG_U2_DISCTH;
-		tmp |= PA6_RG_U2_DISCTH_VAL(instance->discth);
-		writel(tmp, com + U3P_USBPHYACR6);
-	}
+	if (instance->discth)
+		mtk_phy_update_bits(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH,
+				    PA6_RG_U2_DISCTH_VAL(instance->discth));
 }
 
 /* type switch for usb3/pcie/sgmii/sata */
@@ -1147,44 +1014,31 @@ static void phy_efuse_set(struct mtk_phy_instance *instance)
 	struct device *dev = &instance->phy->dev;
 	struct u2phy_banks *u2_banks = &instance->u2_banks;
 	struct u3phy_banks *u3_banks = &instance->u3_banks;
-	u32 tmp;
 
 	if (!instance->efuse_sw_en)
 		return;
 
 	switch (instance->type) {
 	case PHY_TYPE_USB2:
-		tmp = readl(u2_banks->misc + U3P_MISC_REG1);
-		tmp |= MR1_EFUSE_AUTO_LOAD_DIS;
-		writel(tmp, u2_banks->misc + U3P_MISC_REG1);
-
-		tmp = readl(u2_banks->com + U3P_USBPHYACR1);
-		tmp &= ~PA1_RG_INTR_CAL;
-		tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr);
-		writel(tmp, u2_banks->com + U3P_USBPHYACR1);
+		mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1, MR1_EFUSE_AUTO_LOAD_DIS);
+
+		mtk_phy_update_bits(u2_banks->com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
+				    PA1_RG_INTR_CAL_VAL(instance->efuse_intr));
 		break;
 	case PHY_TYPE_USB3:
 	case PHY_TYPE_PCIE:
-		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV);
-		tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS;
-		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV);
-
-		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
-		tmp &= ~P3D_RG_TX_IMPEL;
-		tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp);
-		tmp |= P3D_RG_FORCE_TX_IMPEL;
-		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL0);
-
-		tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
-		tmp &= ~P3D_RG_RX_IMPEL;
-		tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp);
-		tmp |= P3D_RG_FORCE_RX_IMPEL;
-		writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL1);
-
-		tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0);
-		tmp &= ~P3A_RG_IEXT_INTR;
-		tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr);
-		writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0);
+		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_RSV, P3D_RG_EFUSE_AUTO_LOAD_DIS);
+
+		mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL,
+				    P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp));
+		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL);
+
+		mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL,
+				    P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp));
+		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL);
+
+		mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG0, P3A_RG_IEXT_INTR,
+				    P3A_RG_IEXT_INTR_VAL(instance->efuse_intr));
 		break;
 	default:
 		dev_warn(dev, "no sw efuse for type %d\n", instance->type);
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 1/5] dt-bindings: phy: mediatek: tphy: support software efuse load

[Vinod Koul]

On 18-12-21, 16:27, Chunfeng Yun wrote:
> Add optional property nvmem-cells and nvmem-cell-names to support
> software efuse load, this helps to fix the efuse bit shift issue
> on mt8195 etc.

Applied all, thanks

-- 
~Vinod

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 2/5] phy: phy-mtk-tphy: add support efuse setting

[AngeloGioacchino Del Regno]

Il 18/12/21 09:27, Chunfeng Yun ha scritto:
> Due to some SoCs have a bit shift issue that will drop a bit for usb3
> phy or pcie phy, fix it by adding software efuse reading and setting,
> but only support it optionally for version 2/3.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: changes suggested by Vinod
>      1. fix typo of version in commit message
>      2. use dev_dbg() instead of dev_info()
> ---
>   drivers/phy/mediatek/phy-mtk-tphy.c | 162 ++++++++++++++++++++++++++++
>   1 file changed, 162 insertions(+)
> 

Hello Chunfeng, thanks for the patch!
However, there are a few things to improve...

> diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c
> index cdcef865fe9e..98a942c607a6 100644
> --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> @@ -12,6 +12,7 @@
>   #include <linux/iopoll.h>
>   #include <linux/mfd/syscon.h>
>   #include <linux/module.h>
> +#include <linux/nvmem-consumer.h>
>   #include <linux/of_address.h>
>   #include <linux/of_device.h>
>   #include <linux/phy/phy.h>
> @@ -41,6 +42,9 @@
>   #define SSUSB_SIFSLV_V2_U3PHYD		0x200
>   #define SSUSB_SIFSLV_V2_U3PHYA		0x400
>   
> +#define U3P_MISC_REG1		0x04
> +#define MR1_EFUSE_AUTO_LOAD_DIS		BIT(6)
> +
>   #define U3P_USBPHYACR0		0x000
>   #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
>   #define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> @@ -133,6 +137,8 @@
>   #define P3C_RG_SWRST_U3_PHYD_FORCE_EN	BIT(24)
>   
>   #define U3P_U3_PHYA_REG0	0x000
> +#define P3A_RG_IEXT_INTR		GENMASK(15, 10)
> +#define P3A_RG_IEXT_INTR_VAL(x)		((0x3f & (x)) << 10)
>   #define P3A_RG_CLKDRV_OFF		GENMASK(3, 2)
>   #define P3A_RG_CLKDRV_OFF_VAL(x)	((0x3 & (x)) << 2)
>   
> @@ -187,6 +193,19 @@
>   #define P3D_RG_FWAKE_TH		GENMASK(21, 16)
>   #define P3D_RG_FWAKE_TH_VAL(x)	((0x3f & (x)) << 16)
>   
> +#define U3P_U3_PHYD_IMPCAL0		0x010
> +#define P3D_RG_FORCE_TX_IMPEL		BIT(31)
> +#define P3D_RG_TX_IMPEL			GENMASK(28, 24)
> +#define P3D_RG_TX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
> +
> +#define U3P_U3_PHYD_IMPCAL1		0x014
> +#define P3D_RG_FORCE_RX_IMPEL		BIT(31)
> +#define P3D_RG_RX_IMPEL			GENMASK(28, 24)
> +#define P3D_RG_RX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
> +
> +#define U3P_U3_PHYD_RSV			0x054
> +#define P3D_RG_EFUSE_AUTO_LOAD_DIS	BIT(12)
> +
>   #define U3P_U3_PHYD_CDR1		0x05c
>   #define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
>   #define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> @@ -307,6 +326,11 @@ struct mtk_phy_pdata {
>   	 * 48M PLL, fix it by switching PLL to 26M from default 48M
>   	 */
>   	bool sw_pll_48m_to_26m;
> +	/*
> +	 * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
> +	 * support sw way, also support it for v2/v3 optionally.
> +	 */
> +	bool sw_efuse_supported;
>   	enum mtk_phy_version version;
>   };
>   
> @@ -336,6 +360,10 @@ struct mtk_phy_instance {
>   	struct regmap *type_sw;
>   	u32 type_sw_reg;
>   	u32 type_sw_index;
> +	u32 efuse_sw_en;
> +	u32 efuse_intr;
> +	u32 efuse_tx_imp;
> +	u32 efuse_rx_imp;
>   	int eye_src;
>   	int eye_vrt;
>   	int eye_term;
> @@ -1040,6 +1068,130 @@ static int phy_type_set(struct mtk_phy_instance *instance)
>   	return 0;
>   }
>   
> +static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance)
> +{
> +	struct device *dev = &instance->phy->dev;
> +	int ret = 0;
> +
> +	/* tphy v1 doesn't support sw efuse, skip it */
> +	if (!tphy->pdata->sw_efuse_supported) {
> +		instance->efuse_sw_en = 0;
> +		return 0;
> +	}
> +
> +	/* software efuse is optional */
> +	instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells");
> +	if (!instance->efuse_sw_en)
> +		return 0;
> +
> +	switch (instance->type) {
> +	case PHY_TYPE_USB2:
> +		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
> +		if (ret) {
> +			dev_err(dev, "fail to get u2 intr efuse, %d\n", ret);
> +			break;
> +		}
> +
> +		/* no efuse, ignore it */
> +		if (!instance->efuse_intr) {
> +			dev_warn(dev, "no u2 intr efuse, but dts enable it\n");
> +			instance->efuse_sw_en = 0;
> +			break;
> +		}
> +
> +		dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr);
> +		break;
> +
> +	case PHY_TYPE_USB3:
> +	case PHY_TYPE_PCIE:
> +		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
> +		if (ret) {
> +			dev_err(dev, "fail to get u3 intr efuse, %d\n", ret);
> +			break;
> +		}
> +
> +		ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp);
> +		if (ret) {
> +			dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret);
> +			break;
> +		}
> +
> +		ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp);
> +		if (ret) {
> +			dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret);
> +			break;
> +		}
> +
> +		/* no efuse, ignore it */
> +		if (!instance->efuse_intr &&
> +		    !instance->efuse_rx_imp &&
> +		    !instance->efuse_rx_imp) {
> +			dev_warn(dev, "no u3 intr efuse, but dts enable it\n");
> +			instance->efuse_sw_en = 0;
> +			break;
> +		}
> +
> +		dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n",
> +			instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp);
> +		break;
> +	default:
> +		dev_err(dev, "no sw efuse for type %d\n", instance->type);
> +		ret = -EINVAL;
> +	}
> +
> +	return ret;
> +}
> +
> +static void phy_efuse_set(struct mtk_phy_instance *instance)

The name for this function is a bit misleading and one may think that this
is writing efuses (aka blowing a fuse array), which doesn't look like being
the case at all.

What about changing it to phy_set_sw_efuse_params(), or something similar?


Thank you,
- Angelo

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 3/5] phy: mediatek: add helpers to update bits of registers

[AngeloGioacchino Del Regno]

Il 18/12/21 09:28, Chunfeng Yun ha scritto:
> Add three helpers mtk_phy_clear/set/update_bits() for registers operation
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: new patch, add register access helpers,
>      Add updatel() macro suggested by Vinod, here add more ones instead.
> ---
>   drivers/phy/mediatek/phy-mtk-io.h | 38 +++++++++++++++++++++++++++++++
>   1 file changed, 38 insertions(+)
>   create mode 100644 drivers/phy/mediatek/phy-mtk-io.h
> 
> diff --git a/drivers/phy/mediatek/phy-mtk-io.h b/drivers/phy/mediatek/phy-mtk-io.h
> new file mode 100644
> index 000000000000..500fcdab165d
> --- /dev/null
> +++ b/drivers/phy/mediatek/phy-mtk-io.h
> @@ -0,0 +1,38 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2021 MediaTek Inc.
> + *
> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> + */
> +
> +#ifndef __PHY_MTK_H__
> +#define __PHY_MTK_H__
> +
> +#include <linux/io.h>
> +
> +static inline void mtk_phy_clear_bits(void __iomem *reg, u32 bits)
> +{
> +	u32 tmp = readl(reg);
> +
> +	tmp &= ~bits;
> +	writel(tmp, reg);
> +}
> +
> +static inline void mtk_phy_set_bits(void __iomem *reg, u32 bits)
> +{
> +	u32 tmp = readl(reg);
> +
> +	tmp |= bits;
> +	writel(tmp, reg);
> +}
> +
> +static inline void mtk_phy_update_bits(void __iomem *reg, u32 mask, u32 val)
> +{
> +	u32 tmp = readl(reg);
> +
> +	tmp &= ~mask;
> +	tmp |= val & mask;
> +	writel(tmp, reg);
> +}
> +
> +#endif
> 

These helpers are almost exactly duplicating what regmap_update_bits() is doing.
I appreciate the effort to stop open-coding the same sequences over and over by
adding such helper functions, but I think that the proper way of doing what you
are proposing is not to add custom functions but rather reuse what the Linux APIs
give you.

What about doing a conversion to use regmap on this driver?

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 3/5] phy: mediatek: add helpers to update bits of registers

[Chunfeng Yun]

On Fri, 2021-12-24 at 11:10 +0100, AngeloGioacchino Del Regno wrote:
> Il 18/12/21 09:28, Chunfeng Yun ha scritto:
> > Add three helpers mtk_phy_clear/set/update_bits() for registers
> > operation
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v2: new patch, add register access helpers,
> >      Add updatel() macro suggested by Vinod, here add more ones
> > instead.
> > ---
> >   drivers/phy/mediatek/phy-mtk-io.h | 38
> > +++++++++++++++++++++++++++++++
> >   1 file changed, 38 insertions(+)
> >   create mode 100644 drivers/phy/mediatek/phy-mtk-io.h
> > 
> > diff --git a/drivers/phy/mediatek/phy-mtk-io.h
> > b/drivers/phy/mediatek/phy-mtk-io.h
> > new file mode 100644
> > index 000000000000..500fcdab165d
> > --- /dev/null
> > +++ b/drivers/phy/mediatek/phy-mtk-io.h
> > @@ -0,0 +1,38 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + *
> > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > + */
> > +
> > +#ifndef __PHY_MTK_H__
> > +#define __PHY_MTK_H__
> > +
> > +#include <linux/io.h>
> > +
> > +static inline void mtk_phy_clear_bits(void __iomem *reg, u32 bits)
> > +{
> > +	u32 tmp = readl(reg);
> > +
> > +	tmp &= ~bits;
> > +	writel(tmp, reg);
> > +}
> > +
> > +static inline void mtk_phy_set_bits(void __iomem *reg, u32 bits)
> > +{
> > +	u32 tmp = readl(reg);
> > +
> > +	tmp |= bits;
> > +	writel(tmp, reg);
> > +}
> > +
> > +static inline void mtk_phy_update_bits(void __iomem *reg, u32
> > mask, u32 val)
> > +{
> > +	u32 tmp = readl(reg);
> > +
> > +	tmp &= ~mask;
> > +	tmp |= val & mask;
> > +	writel(tmp, reg);
> > +}
> > +
> > +#endif
> > 
> 
> These helpers are almost exactly duplicating what
> regmap_update_bits() is doing.
> I appreciate the effort to stop open-coding the same sequences over
> and over by
> adding such helper functions, 
I agree with you.
> but I think that the proper way of doing what you
> are proposing is not to add custom functions but rather reuse what
> the Linux APIs
> give you.
I also like to use common APIs ASAP, but not found suitable ones.
This may be a problem, I found that some similar custom helps already
added under phy fold.

> 
> What about doing a conversion to use regmap on this driver?
No, we don't use regmap here, these registers are monopolized by t-phy, 
it's not syscon.


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 2/5] phy: phy-mtk-tphy: add support efuse setting

[Chunfeng Yun]

On Fri, 2021-12-24 at 11:03 +0100, AngeloGioacchino Del Regno wrote:
> Il 18/12/21 09:27, Chunfeng Yun ha scritto:
> > Due to some SoCs have a bit shift issue that will drop a bit for
> > usb3
> > phy or pcie phy, fix it by adding software efuse reading and
> > setting,
> > but only support it optionally for version 2/3.
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v2: changes suggested by Vinod
> >      1. fix typo of version in commit message
> >      2. use dev_dbg() instead of dev_info()
> > ---
> >   drivers/phy/mediatek/phy-mtk-tphy.c | 162
> > ++++++++++++++++++++++++++++
> >   1 file changed, 162 insertions(+)
> > 
> 
> Hello Chunfeng, thanks for the patch!
> However, there are a few things to improve...
> 
> > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c
> > b/drivers/phy/mediatek/phy-mtk-tphy.c
> > index cdcef865fe9e..98a942c607a6 100644
> > --- a/drivers/phy/mediatek/phy-mtk-tphy.c
> > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c
> > @@ -12,6 +12,7 @@
> >   #include <linux/iopoll.h>
> >   #include <linux/mfd/syscon.h>
> >   #include <linux/module.h>
> > +#include <linux/nvmem-consumer.h>
> >   #include <linux/of_address.h>
> >   #include <linux/of_device.h>
> >   #include <linux/phy/phy.h>
> > @@ -41,6 +42,9 @@
> >   #define SSUSB_SIFSLV_V2_U3PHYD		0x200
> >   #define SSUSB_SIFSLV_V2_U3PHYA		0x400
> >   
> > +#define U3P_MISC_REG1		0x04
> > +#define MR1_EFUSE_AUTO_LOAD_DIS		BIT(6)
> > +
> >   #define U3P_USBPHYACR0		0x000
> >   #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
> >   #define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
> > @@ -133,6 +137,8 @@
> >   #define P3C_RG_SWRST_U3_PHYD_FORCE_EN	BIT(24)
> >   
> >   #define U3P_U3_PHYA_REG0	0x000
> > +#define P3A_RG_IEXT_INTR		GENMASK(15, 10)
> > +#define P3A_RG_IEXT_INTR_VAL(x)		((0x3f & (x)) << 10)
> >   #define P3A_RG_CLKDRV_OFF		GENMASK(3, 2)
> >   #define P3A_RG_CLKDRV_OFF_VAL(x)	((0x3 & (x)) << 2)
> >   
> > @@ -187,6 +193,19 @@
> >   #define P3D_RG_FWAKE_TH		GENMASK(21, 16)
> >   #define P3D_RG_FWAKE_TH_VAL(x)	((0x3f & (x)) << 16)
> >   
> > +#define U3P_U3_PHYD_IMPCAL0		0x010
> > +#define P3D_RG_FORCE_TX_IMPEL		BIT(31)
> > +#define P3D_RG_TX_IMPEL			GENMASK(28, 24)
> > +#define P3D_RG_TX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
> > +
> > +#define U3P_U3_PHYD_IMPCAL1		0x014
> > +#define P3D_RG_FORCE_RX_IMPEL		BIT(31)
> > +#define P3D_RG_RX_IMPEL			GENMASK(28, 24)
> > +#define P3D_RG_RX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
> > +
> > +#define U3P_U3_PHYD_RSV			0x054
> > +#define P3D_RG_EFUSE_AUTO_LOAD_DIS	BIT(12)
> > +
> >   #define U3P_U3_PHYD_CDR1		0x05c
> >   #define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
> >   #define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > @@ -307,6 +326,11 @@ struct mtk_phy_pdata {
> >   	 * 48M PLL, fix it by switching PLL to 26M from default 48M
> >   	 */
> >   	bool sw_pll_48m_to_26m;
> > +	/*
> > +	 * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
> > +	 * support sw way, also support it for v2/v3 optionally.
> > +	 */
> > +	bool sw_efuse_supported;
> >   	enum mtk_phy_version version;
> >   };
> >   
> > @@ -336,6 +360,10 @@ struct mtk_phy_instance {
> >   	struct regmap *type_sw;
> >   	u32 type_sw_reg;
> >   	u32 type_sw_index;
> > +	u32 efuse_sw_en;
> > +	u32 efuse_intr;
> > +	u32 efuse_tx_imp;
> > +	u32 efuse_rx_imp;
> >   	int eye_src;
> >   	int eye_vrt;
> >   	int eye_term;
> > @@ -1040,6 +1068,130 @@ static int phy_type_set(struct
> > mtk_phy_instance *instance)
> >   	return 0;
> >   }
> >   
> > +static int phy_efuse_get(struct mtk_tphy *tphy, struct
> > mtk_phy_instance *instance)
> > +{
> > +	struct device *dev = &instance->phy->dev;
> > +	int ret = 0;
> > +
> > +	/* tphy v1 doesn't support sw efuse, skip it */
> > +	if (!tphy->pdata->sw_efuse_supported) {
> > +		instance->efuse_sw_en = 0;
> > +		return 0;
> > +	}
> > +
> > 
> > [...]
> > 
> > +
> > +		dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp
> > %x\n",
> > +			instance->efuse_intr, instance-
> > >efuse_rx_imp,instance->efuse_tx_imp);
> > +		break;
> > +	default:
> > +		dev_err(dev, "no sw efuse for type %d\n", instance-
> > >type);
> > +		ret = -EINVAL;
> > +	}
> > +
> > +	return ret;
> > +}
> > +
> > +static void phy_efuse_set(struct mtk_phy_instance *instance)
> 
> The name for this function is a bit misleading and one may think that
> this
> is writing efuses (aka blowing a fuse array), 
The hardware efuses on MediaTek platform only support Read-Only.

> which doesn't look like being
> the case at all.
> 
> What about changing it to phy_set_sw_efuse_params(), or something
> similar?
It seems better, I'll prepare a new patch.
> 
> 
> Thank you,
> - Angelo
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 3/5] phy: mediatek: add helpers to update bits of registers

[AngeloGioacchino Del Regno]

Il 30/12/21 03:06, Chunfeng Yun ha scritto:
> On Fri, 2021-12-24 at 11:10 +0100, AngeloGioacchino Del Regno wrote:
>> Il 18/12/21 09:28, Chunfeng Yun ha scritto:
>>> Add three helpers mtk_phy_clear/set/update_bits() for registers
>>> operation
>>>
>>> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
>>> ---
>>> v2: new patch, add register access helpers,
>>>       Add updatel() macro suggested by Vinod, here add more ones
>>> instead.
>>> ---
>>>    drivers/phy/mediatek/phy-mtk-io.h | 38
>>> +++++++++++++++++++++++++++++++
>>>    1 file changed, 38 insertions(+)
>>>    create mode 100644 drivers/phy/mediatek/phy-mtk-io.h
>>>
>>> diff --git a/drivers/phy/mediatek/phy-mtk-io.h
>>> b/drivers/phy/mediatek/phy-mtk-io.h
>>> new file mode 100644
>>> index 000000000000..500fcdab165d
>>> --- /dev/null
>>> +++ b/drivers/phy/mediatek/phy-mtk-io.h
>>> @@ -0,0 +1,38 @@
>>> +/* SPDX-License-Identifier: GPL-2.0 */
>>> +/*
>>> + * Copyright (C) 2021 MediaTek Inc.
>>> + *
>>> + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
>>> + */
>>> +
>>> +#ifndef __PHY_MTK_H__
>>> +#define __PHY_MTK_H__
>>> +
>>> +#include <linux/io.h>
>>> +
>>> +static inline void mtk_phy_clear_bits(void __iomem *reg, u32 bits)
>>> +{
>>> +	u32 tmp = readl(reg);
>>> +
>>> +	tmp &= ~bits;
>>> +	writel(tmp, reg);
>>> +}
>>> +
>>> +static inline void mtk_phy_set_bits(void __iomem *reg, u32 bits)
>>> +{
>>> +	u32 tmp = readl(reg);
>>> +
>>> +	tmp |= bits;
>>> +	writel(tmp, reg);
>>> +}
>>> +
>>> +static inline void mtk_phy_update_bits(void __iomem *reg, u32
>>> mask, u32 val)
>>> +{
>>> +	u32 tmp = readl(reg);
>>> +
>>> +	tmp &= ~mask;
>>> +	tmp |= val & mask;
>>> +	writel(tmp, reg);
>>> +}
>>> +
>>> +#endif
>>>
>>
>> These helpers are almost exactly duplicating what
>> regmap_update_bits() is doing.
>> I appreciate the effort to stop open-coding the same sequences over
>> and over by
>> adding such helper functions,
> I agree with you.
>> but I think that the proper way of doing what you
>> are proposing is not to add custom functions but rather reuse what
>> the Linux APIs
>> give you.
> I also like to use common APIs ASAP, but not found suitable ones.
> This may be a problem, I found that some similar custom helps already
> added under phy fold.
> 
>>
>> What about doing a conversion to use regmap on this driver?
> No, we don't use regmap here, these registers are monopolized by t-phy,
> it's not syscon.
> 
> 

Hello,

The regmap API allows this kind of usage, registers don't necessarily have
to be part of a syscon.

Regards,
- Angelo

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 3/5] phy: mediatek: add helpers to update bits of registers

[Chunfeng Yun]

On Mon, 2022-01-03 at 09:59 +0100, AngeloGioacchino Del Regno wrote:
> Il 30/12/21 03:06, Chunfeng Yun ha scritto:
> > On Fri, 2021-12-24 at 11:10 +0100, AngeloGioacchino Del Regno
> > wrote:
> > > Il 18/12/21 09:28, Chunfeng Yun ha scritto:
> > > > Add three helpers mtk_phy_clear/set/update_bits() for registers
> > > > operation
> > > > 
> > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > > > ---
> > > > v2: new patch, add register access helpers,
> > > >       Add updatel() macro suggested by Vinod, here add more
> > > > ones
> > > > instead.
> > > > ---
> > > >    drivers/phy/mediatek/phy-mtk-io.h | 38
> > > > +++++++++++++++++++++++++++++++
> > > >    1 file changed, 38 insertions(+)
> > > >    create mode 100644 drivers/phy/mediatek/phy-mtk-io.h
> > > > 
> > > > diff --git a/drivers/phy/mediatek/phy-mtk-io.h
> > > > b/drivers/phy/mediatek/phy-mtk-io.h
> > > > new file mode 100644
> > > > index 000000000000..500fcdab165d
> > > > --- /dev/null
> > > > +++ b/drivers/phy/mediatek/phy-mtk-io.h
> > > > @@ -0,0 +1,38 @@
> > > > +/* SPDX-License-Identifier: GPL-2.0 */
> > > > +/*
> > > > + * Copyright (C) 2021 MediaTek Inc.
> > > > + *
> > > > + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > > > + */
> > > > +
> > > > +#ifndef __PHY_MTK_H__
> > > > +#define __PHY_MTK_H__
> > > > +
> > > > +#include <linux/io.h>
> > > > +
> > > > +static inline void mtk_phy_clear_bits(void __iomem *reg, u32
> > > > bits)
> > > > +{
> > > > +	u32 tmp = readl(reg);
> > > > +
> > > > +	tmp &= ~bits;
> > > > +	writel(tmp, reg);
> > > > +}
> > > > +
> > > > +static inline void mtk_phy_set_bits(void __iomem *reg, u32
> > > > bits)
> > > > +{
> > > > +	u32 tmp = readl(reg);
> > > > +
> > > > +	tmp |= bits;
> > > > +	writel(tmp, reg);
> > > > +}
> > > > +
> > > > +static inline void mtk_phy_update_bits(void __iomem *reg, u32
> > > > mask, u32 val)
> > > > +{
> > > > +	u32 tmp = readl(reg);
> > > > +
> > > > +	tmp &= ~mask;
> > > > +	tmp |= val & mask;
> > > > +	writel(tmp, reg);
> > > > +}
> > > > +
> > > > +#endif
> > > > 
> > > 
> > > These helpers are almost exactly duplicating what
> > > regmap_update_bits() is doing.
> > > I appreciate the effort to stop open-coding the same sequences
> > > over
> > > and over by
> > > adding such helper functions,
> > 
> > I agree with you.
> > > but I think that the proper way of doing what you
> > > are proposing is not to add custom functions but rather reuse
> > > what
> > > the Linux APIs
> > > give you.
> > 
> > I also like to use common APIs ASAP, but not found suitable ones.
> > This may be a problem, I found that some similar custom helps
> > already
> > added under phy fold.
> > 
> > > 
> > > What about doing a conversion to use regmap on this driver?
> > 
> > No, we don't use regmap here, these registers are monopolized by t-
> > phy,
> > it's not syscon.
> > 
> > 
> 
> Hello,
> 
> The regmap API allows this kind of usage, registers don't necessarily
> have
> to be part of a syscon.
I'm sorry, I don't want to make it more complex

> 
> Regards,
> - Angelo
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek