[PATCH v3 00/11] Introduce STM32 Firewall framework

[PATCH v3 00/11] Introduce STM32 Firewall framework

[Gatien Chevallier]

Introduce STM32 Firewall framework for STM32MP1x and STM32MP2x
platforms. STM32MP1x(ETZPC) and STM32MP2x(RIFSC) Firewall controllers
register to the framework to offer firewall services such as access
granting.

This series of patches is a new approach on the previous STM32 system
bus, history is available here:
https://lore.kernel.org/lkml/20230127164040.1047583/

The need for such framework arises from the fact that there are now
multiple hardware firewalls implemented across multiple products.
Drivers are shared between different products, using the same code.
When it comes to firewalls, the purpose mostly stays the same: Protect
hardware resources. But the implementation differs, and there are
multiple types of firewalls: peripheral, memory, ... 

Some hardware firewall controllers such as the RIFSC implemented on
STM32MP2x platforms may require to take ownership of a resource before
being able to use it, hence the requirement for firewall services to
take/release the ownership of such resources.

On the other hand, hardware firewall configurations are becoming
more and more complex. These mecanisms prevent platform crashes
or other firewall-related incoveniences by denying access to some
resources.

The stm32 firewall framework offers an API that is defined in
firewall controllers drivers to best fit the specificity of each
firewall.

For every peripherals protected by either the ETZPC or the RIFSC, the
firewall framework checks the firewall controlelr registers to see if
the peripheral's access is granted to the Linux kernel. If not, the
peripheral is configured as secure, the node is marked populated,
so that the driver is not probed for that device.

The firewall framework relies on the feature-domain-controller device
tree bindings: https://lore.kernel.org/lkml/0c0a82bb-18ae-d057-562b.
It is used by peripherals to reference a domain controller, in this
case a firewall feature domain. The bus uses the ID referenced by
the feature-domains property to know where to look in the firewall
to get the security configuration for the peripheral. This allows
a device tree description rather than a hardcoded peripheral table
in the bus driver.

The STM32 ETZPC device is responsible for filtering accesses based on
security level, or co-processor isolation for any resource connected
to it.

The RIFSC is responsible for filtering accesses based on Compartment
ID / security level / privilege level for any resource connected to
it.

STM32MP13/15/25 SoC device tree files are updated in this series to
implement this mecanism.

Changes in V2:

	generic:
		- Add fw_devlink dependency for "feature-domains"
		  property.

	bindings:
		- Corrected YAMLS errors highlighted by Rob's robot
		- Firewall controllers YAMLs no longer define the
		  maxItems for the "feature-domains" property
		- Renamed st,stm32-rifsc.yaml to
		  st,stm32mp25-rifsc.yaml
		- Fix examples in YAML files
		- Change feature-domains maxItems to 2 in firewall
		  consumer files as there should not be more than
		  2 entries for now
		- Declare "feature-domain-names" as an optional
		  property for firewall controllers child nodes.
		- Add missing "feature-domains" property declaration
		  in bosch,m_can.yaml and st,stm32-cryp.yaml files

	firewall framework:
		- Support multiple entries for "feature-domains"
		  property
		- Better handle the device-tree parsing using
		  phandle+args APIs
		- Remove "resource firewall" type
		- Add a field for the name of the firewall entry
		- Fix licenses
	
	RIFSC:
		- Add controller name
		- Driver is now a module_platform_driver
		- Fix license

	ETZPC:
		- Add controller name
		- Driver is now a module_platform_driver
		- Fix license

	Device trees:
		- Fix rifsc node name
		- Move the "ranges" property under the
		  "feature-domains" one

Changes in V3:

	Change incorrect ordering for bindings commits leading
	to an error while running
	"make DT_CHECKER_FLAGS=-m dt_binding_check"

Oleksii Moisieiev (1):
  dt-bindings: Document common device controller bindings

Gatien Chevallier (10):
  dt-bindings: treewide: add feature-domains description
  dt-bindings: bus: document RIFSC
  dt-bindings: bus: document ETZPC
  firewall: introduce stm32_firewall framework
  of: property: fw_devlink: Add support for "feature-domains"
  bus: rifsc: introduce RIFSC firewall controller driver
  arm64: dts: st: add RIFSC as a domain controller for STM32MP25x boards
  bus: etzpc: introduce ETZPC firewall controller driver
  ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards
  ARM: dts: stm32: add ETZPC as a system bus for STM32MP13x boards

 .../bindings/bus/st,stm32-etzpc.yaml          |   96 +
 .../bindings/bus/st,stm32mp25-rifsc.yaml      |  105 +
 .../bindings/crypto/st,stm32-cryp.yaml        |    4 +
 .../bindings/crypto/st,stm32-hash.yaml        |    4 +
 .../devicetree/bindings/dma/st,stm32-dma.yaml |    4 +
 .../bindings/dma/st,stm32-dmamux.yaml         |    4 +
 .../feature-domain-controller.yaml            |   84 +
 .../devicetree/bindings/i2c/st,stm32-i2c.yaml |    4 +
 .../bindings/iio/adc/st,stm32-adc.yaml        |    4 +
 .../bindings/iio/adc/st,stm32-dfsdm-adc.yaml  |    4 +
 .../bindings/iio/dac/st,stm32-dac.yaml        |    4 +
 .../bindings/media/cec/st,stm32-cec.yaml      |    4 +
 .../bindings/media/st,stm32-dcmi.yaml         |    4 +
 .../memory-controllers/st,stm32-fmc2-ebi.yaml |    4 +
 .../bindings/mfd/st,stm32-lptimer.yaml        |    4 +
 .../bindings/mfd/st,stm32-timers.yaml         |    5 +
 .../devicetree/bindings/mmc/arm,pl18x.yaml    |    4 +
 .../bindings/net/can/bosch,m_can.yaml         |    4 +
 .../devicetree/bindings/net/stm32-dwmac.yaml  |    4 +
 .../bindings/phy/phy-stm32-usbphyc.yaml       |    4 +
 .../bindings/regulator/st,stm32-vrefbuf.yaml  |    4 +
 .../devicetree/bindings/rng/st,stm32-rng.yaml |    4 +
 .../bindings/serial/st,stm32-uart.yaml        |    4 +
 .../bindings/sound/st,stm32-i2s.yaml          |    4 +
 .../bindings/sound/st,stm32-sai.yaml          |    4 +
 .../bindings/sound/st,stm32-spdifrx.yaml      |    4 +
 .../bindings/spi/st,stm32-qspi.yaml           |    4 +
 .../devicetree/bindings/spi/st,stm32-spi.yaml |    4 +
 .../devicetree/bindings/usb/dwc2.yaml         |    4 +
 MAINTAINERS                                   |    7 +
 arch/arm/boot/dts/st/stm32mp131.dtsi          | 1027 +++---
 arch/arm/boot/dts/st/stm32mp133.dtsi          |   51 +-
 arch/arm/boot/dts/st/stm32mp13xc.dtsi         |   19 +-
 arch/arm/boot/dts/st/stm32mp13xf.dtsi         |   19 +-
 arch/arm/boot/dts/st/stm32mp151.dtsi          | 2757 +++++++++--------
 arch/arm/boot/dts/st/stm32mp153.dtsi          |   52 +-
 arch/arm/boot/dts/st/stm32mp15xc.dtsi         |   19 +-
 arch/arm64/Kconfig.platforms                  |    1 +
 arch/arm64/boot/dts/st/stm32mp251.dtsi        |    7 +-
 drivers/bus/Kconfig                           |    9 +
 drivers/bus/Makefile                          |    1 +
 drivers/bus/stm32_etzpc.c                     |  141 +
 drivers/bus/stm32_firewall.c                  |  288 ++
 drivers/bus/stm32_firewall.h                  |   83 +
 drivers/bus/stm32_rifsc.c                     |  252 ++
 drivers/of/property.c                         |    2 +
 include/linux/bus/stm32_firewall_device.h     |  140 +
 47 files changed, 3346 insertions(+), 1919 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
 create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml
 create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
 create mode 100644 drivers/bus/stm32_etzpc.c
 create mode 100644 drivers/bus/stm32_firewall.c
 create mode 100644 drivers/bus/stm32_firewall.h
 create mode 100644 drivers/bus/stm32_rifsc.c
 create mode 100644 include/linux/bus/stm32_firewall_device.h

-- 
2.25.1

[IGNORE][PATCH v3 01/11] dt-bindings: Document common device controller bindings

[Gatien Chevallier]

From: Oleksii Moisieiev <Oleksii_Moisieiev@epam.com>

Introducing of the common device controller bindings for the controller
provider and consumer devices. Those bindings are intended to allow
divided system on chip into muliple domains, that can be used to
configure hardware permissions.

Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
---
 .../feature-domain-controller.yaml            | 84 +++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml

diff --git a/Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml b/Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
new file mode 100644
index 000000000000..90a7c38c833c
--- /dev/null
+++ b/Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
@@ -0,0 +1,84 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/feature-controllers/feature-domain-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Domain Controller bindings
+
+maintainers:
+  - Oleksii Moisieiev <oleksii_moisieiev@epam.com>
+
+description: |+
+  Common Feature Domains Controller bindings properties
+
+  Domain controllers allow to divided system on chip into multiple feature
+  domains that can be used to select by who hardware blocks could be accessed.
+  A feature domain could be a cluster of CPUs (or coprocessors), a range of
+  addresses or a group of hardware blocks.
+
+  This device tree bindings can be used to bind feature domain consumer devices
+  with their feature domains provided by feature-domains controllers.
+  Feature omain controller provider can be represened by any node in the
+  device tree and can provide one or more configuration parameters, needed to
+  control parameters of the consumer device. A consumer node can refer to the
+  provider by phandle and a set of phandle arguments, specified by
+  '#feature-domain-cells' property in the device controller provider node.
+
+  Device controllers are typically used to set the permissions of the hardware
+  block. The contents of the feature-domains configuration properties are
+  defined by the binding for the individual feature-domains controller device.
+
+  Each node can be a consumer for the several providers. The first
+  configuration of 'feature-domains' or the one named 'default' is applied
+  before probing the device itself.
+
+# always select the core schema
+select: true
+
+properties:
+  '#feature-domain-cells':
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Number of cells in a feature-domains controller specifier;
+      Can be any value as specified by device tree binding documentation
+      of a particular provider.
+
+  feature-domain-controller:
+    description:
+      Indicates that the node is feature-domain-controller provider.
+
+  feature-domain-names:
+    $ref: '/schemas/types.yaml#/definitions/string-array'
+    description:
+      A list of feature-domains names, sorted in the same order as
+      feature-domains entries. Consumer drivers will use feature-domain-names
+      to match with existing feature-domains entries.
+
+  feature-domains:
+    $ref: "/schemas/types.yaml#/definitions/phandle-array"
+    description:
+      A list of feature-domains controller specifiers, as defined by the
+      bindings of the feature-domain-controller provider.
+
+additionalProperties: true
+
+examples:
+  - |
+    ctrl0: ctrl@100 {
+        feature-domain-controller;
+        reg = <0x100 0x10>;
+        #feature-domain-cells = <2>;
+    };
+
+    ctrl1: ctrl@110 {
+        feature-domain-controller;
+        reg = <0x110 0x10>;
+        #feature-domain-cells = <3>;
+    };
+
+    foo@0 {
+        reg = <0x0 0x1>;
+        feature-domains = <&ctrl0 1 2>, <&ctrl1 3 4 5>;
+        feature-domain-names = "default", "unbind";
+    };
-- 
2.25.1

[PATCH v3 02/11] dt-bindings: treewide: add feature-domains description

[Gatien Chevallier]

feature-domains is an optional property that allows a peripheral to
refer to one or more feature domain controller(s).

Description of this property is added to all peripheral binding files of
the peripheral under the STM32 firewall controllers. It allows an accurate
representation of the hardware, where various peripherals are connected
to this firewall bus. The firewall can then check the peripheral accesses
before allowing it to probe.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2: 
	- Add missing "feature-domains" property declaration
	  in bosch,m_can.yaml and st,stm32-cryp.yaml files

 Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml  | 4 ++++
 Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml  | 4 ++++
 Documentation/devicetree/bindings/dma/st,stm32-dma.yaml      | 4 ++++
 Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml   | 4 ++++
 Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml      | 4 ++++
 Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml  | 4 ++++
 .../devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml      | 4 ++++
 Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml  | 4 ++++
 .../devicetree/bindings/media/cec/st,stm32-cec.yaml          | 4 ++++
 Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml   | 4 ++++
 .../bindings/memory-controllers/st,stm32-fmc2-ebi.yaml       | 4 ++++
 Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml  | 4 ++++
 Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml   | 5 +++++
 Documentation/devicetree/bindings/mmc/arm,pl18x.yaml         | 4 ++++
 Documentation/devicetree/bindings/net/can/bosch,m_can.yaml   | 4 ++++
 Documentation/devicetree/bindings/net/stm32-dwmac.yaml       | 4 ++++
 Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml | 4 ++++
 .../devicetree/bindings/regulator/st,stm32-vrefbuf.yaml      | 4 ++++
 Documentation/devicetree/bindings/rng/st,stm32-rng.yaml      | 4 ++++
 Documentation/devicetree/bindings/serial/st,stm32-uart.yaml  | 4 ++++
 Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml    | 4 ++++
 Documentation/devicetree/bindings/sound/st,stm32-sai.yaml    | 4 ++++
 .../devicetree/bindings/sound/st,stm32-spdifrx.yaml          | 4 ++++
 Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml     | 4 ++++
 Documentation/devicetree/bindings/spi/st,stm32-spi.yaml      | 4 ++++
 Documentation/devicetree/bindings/usb/dwc2.yaml              | 4 ++++
 26 files changed, 105 insertions(+)

diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
index 0ddeb8a9a7a0..87a578327fc0 100644
--- a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
+++ b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
@@ -46,6 +46,10 @@ properties:
   power-domains:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
index b767ec72a999..042a1e005ab2 100644
--- a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
+++ b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
@@ -50,6 +50,10 @@ properties:
   power-domains:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
index 329847ef096a..9f60915e6130 100644
--- a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
+++ b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
@@ -82,6 +82,10 @@ properties:
     description: if defined, it indicates that the controller
       supports memory-to-memory transfer
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
index e722fbcd8a5f..15d33d41098f 100644
--- a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
+++ b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
@@ -28,6 +28,10 @@ properties:
   resets:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
index 94b75d9f66cd..8a1a21faab8c 100644
--- a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
@@ -99,6 +99,10 @@ properties:
 
   wakeup-source: true
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
index 995cbf8cefc6..d59ac9282a28 100644
--- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
@@ -93,6 +93,10 @@ properties:
   '#size-cells':
     const: 0
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 allOf:
   - if:
       properties:
diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
index 1970503389aa..39ee55aa4dd8 100644
--- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
@@ -59,6 +59,10 @@ properties:
       If not, SPI CLKOUT frequency will not be accurate.
     maximum: 20000000
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
index 04045b932bd2..184d0a44d1de 100644
--- a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
+++ b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
@@ -45,6 +45,10 @@ properties:
   '#size-cells':
     const: 0
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 additionalProperties: false
 
 required:
diff --git a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
index 2314a9a14650..41db21373301 100644
--- a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
+++ b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
@@ -29,6 +29,10 @@ properties:
       - const: cec
       - const: hdmi-cec
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
index 6b3e413cedb2..81e1cd5e30cc 100644
--- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
@@ -36,6 +36,10 @@ properties:
   resets:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
   port:
     $ref: /schemas/graph.yaml#/$defs/port-base
     unevaluatedProperties: false
diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
index 14f1833d37c9..4ef01ee4a5e5 100644
--- a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
@@ -45,6 +45,10 @@ properties:
       Reflects the memory layout with four integer values per bank. Format:
       <bank-number> 0 <address of the bank> <size>
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 patternProperties:
   "^.*@[0-4],[a-f0-9]+$":
     additionalProperties: true
diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
index 27329c5dc38e..156aed282fb8 100644
--- a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
+++ b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
@@ -44,6 +44,10 @@ properties:
 
   wakeup-source: true
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
   pwm:
     type: object
     additionalProperties: false
diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
index f84e09a5743b..d19981ef3fce 100644
--- a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
+++ b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
@@ -67,6 +67,11 @@ properties:
   "#size-cells":
     const: 0
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
+
   pwm:
     type: object
     additionalProperties: false
diff --git a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
index 2459a55ed540..5a8b53d5c35f 100644
--- a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
+++ b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
@@ -79,6 +79,10 @@ properties:
           - const: rx
           - const: tx
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
   power-domains: true
 
   resets:
diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
index 67879aab623b..144cbcbefa37 100644
--- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
+++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
@@ -118,6 +118,10 @@ properties:
   phys:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
index fc8c96b08d7d..133e1edbd561 100644
--- a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
+++ b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
@@ -93,6 +93,10 @@ properties:
       select RCC clock instead of ETH_REF_CLK.
     type: boolean
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - clocks
diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
index 24a3dbde223b..89fa65f31d20 100644
--- a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
@@ -55,6 +55,10 @@ properties:
     description: number of clock cells for ck_usbo_48m consumer
     const: 0
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 # Required child nodes:
 
 patternProperties:
diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
index 05f4ad2c7d3a..b73a97f89fe4 100644
--- a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
+++ b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
@@ -30,6 +30,10 @@ properties:
   vdda-supply:
     description: phandle to the vdda input analog voltage.
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
index 187b172d0cca..c45e6285653c 100644
--- a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
+++ b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
@@ -30,6 +30,10 @@ properties:
     type: boolean
     description: If set enable the clock detection management
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
index 1df8ffe95fc6..b80d5a8ff4e8 100644
--- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
+++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
@@ -70,6 +70,10 @@ properties:
     enum: [1, 2, 4, 8, 12, 14, 16]
     default: 8
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 allOf:
   - $ref: rs485.yaml#
   - $ref: serial.yaml#
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
index b9111d375b93..30339447cc24 100644
--- a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
+++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
@@ -65,6 +65,10 @@ properties:
     $ref: audio-graph-port.yaml#
     unevaluatedProperties: false
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - "#sound-dai-cells"
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
index 56d206f97a96..f59770ead3e3 100644
--- a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
+++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
@@ -48,6 +48,10 @@ properties:
   clock-names:
     maxItems: 3
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
index bc48151b9adb..480ce8704fda 100644
--- a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
+++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
@@ -50,6 +50,10 @@ properties:
   resets:
     maxItems: 1
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - "#sound-dai-cells"
diff --git a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
index 8bba965a9ae6..3331f6cd1b75 100644
--- a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
+++ b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
@@ -46,6 +46,10 @@ properties:
       - const: tx
       - const: rx
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
index 9ca1a843c820..a0664a0fcabf 100644
--- a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
@@ -59,6 +59,10 @@ properties:
       - const: rx
       - const: tx
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 patternProperties:
   "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
     type: object
diff --git a/Documentation/devicetree/bindings/usb/dwc2.yaml b/Documentation/devicetree/bindings/usb/dwc2.yaml
index 0a5c98ea711d..95b615ee3a07 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.yaml
+++ b/Documentation/devicetree/bindings/usb/dwc2.yaml
@@ -172,6 +172,10 @@ properties:
 
   tpl-support: true
 
+  feature-domains:
+    minItems: 1
+    maxItems: 2
+
 dependencies:
   port: [ usb-role-switch ]
   role-switch-default-mode: [ usb-role-switch ]
-- 
2.25.1

[PATCH v3 03/11] dt-bindings: bus: document RIFSC

[Gatien Chevallier]

Document RIFSC (RIF security controller). RIFSC is a firewall controller
composed of different kinds of hardware resources.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2: 
	- Corrected errors highlighted by Rob's robot
	- No longer define the maxItems for the "feature-domains"
	  property
	- Fix example (node name, status)
	- Declare "feature-domain-names" as an optional
	  property for child nodes
	- Fix description of "feature-domains" property

 .../bindings/bus/st,stm32mp25-rifsc.yaml      | 105 ++++++++++++++++++
 1 file changed, 105 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml

diff --git a/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml b/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml
new file mode 100644
index 000000000000..7aeb38296616
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bus/st,stm32mp25-rifsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STM32 Resource isolation framework security controller
+
+maintainers:
+  - Gatien Chevallier <gatien.chevallier@foss.st.com>
+
+description: |
+  Resource isolation framework (RIF) is a comprehensive set of hardware blocks
+  designed to enforce and manage isolation of STM32 hardware resources like
+  memory and peripherals.
+
+  The RIFSC (RIF security controller) is composed of three sets of registers,
+  each managing a specific set of hardware resources:
+    - RISC registers associated with RISUP logic (resource isolation device unit
+      for peripherals), assign all non-RIF aware peripherals to zero, one or
+      any security domains (secure, privilege, compartment).
+    - RIMC registers: associated with RIMU logic (resource isolation master
+      unit), assign all non RIF-aware bus master to one security domain by
+      setting secure, privileged and compartment information on the system bus.
+      Alternatively, the RISUP logic controlling the device port access to a
+      peripheral can assign target bus attributes to this peripheral master port
+      (supported attribute: CID).
+    - RISC registers associated with RISAL logic (resource isolation device unit
+      for address space - Lite version), assign address space subregions to one
+      security domains (secure, privilege, compartment).
+
+properties:
+  compatible:
+    contains:
+      const: st,stm32mp25-rifsc
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  ranges: true
+
+  "#feature-domain-cells":
+    const: 1
+
+  feature-domain-controller: true
+
+patternProperties:
+  "^.*@[0-9a-f]+$":
+    description: Peripherals
+    type: object
+    properties:
+      feature-domains:
+        minItems: 1
+        description:
+          The phandle of the firewall controller of the peripheral and the
+          platform-specific firewall ID of the peripheral.
+
+      feature-domain-names:
+        minItems: 1
+
+    required:
+      - feature-domains
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - feature-domain-controller
+  - "#feature-domain-cells"
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    // In this example, the usart2 device refers to rifsc as its domain
+    // controller.
+    // Access rights are verified before creating devices.
+
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    rifsc: bus@42080000 {
+        compatible = "st,stm32mp25-rifsc";
+        reg = <0x42080000 0x1000>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        feature-domain-controller;
+        #feature-domain-cells = <1>;
+        ranges;
+
+        usart2: serial@400e0000 {
+              compatible = "st,stm32h7-uart";
+              reg = <0x400e0000 0x400>;
+              interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+              clocks = <&ck_flexgen_08>;
+              feature-domains = <&rifsc 32>;
+        };
+    };
-- 
2.25.1

Re: [IGNORE][PATCH v3 01/11] dt-bindings: Document common device controller bindings

[Greg KH]

On Wed, Jul 26, 2023 at 10:38:00AM +0200, Gatien Chevallier wrote:
> From: Oleksii Moisieiev <Oleksii_Moisieiev@epam.com>
> 
> Introducing of the common device controller bindings for the controller
> provider and consumer devices. Those bindings are intended to allow
> divided system on chip into muliple domains, that can be used to
> configure hardware permissions.
> 
> Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
> ---
>  .../feature-domain-controller.yaml            | 84 +++++++++++++++++++
>  1 file changed, 84 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml

What is the [IGNORE] prefix for?

[PATCH v3 04/11] dt-bindings: bus: document ETZPC

[Gatien Chevallier]

Document ETZPC (Extended TrustZone protection controller). ETZPC is a
firewall controller.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2: 
	- Corrected errors highlighted by Rob's robot
	- No longer define the maxItems for the "feature-domains"
	  property
	- Fix example (node name, status)
	- Declare "feature-domain-names" as an optional
	  property for child nodes
	- Fix description of "feature-domains" property
	- Reorder the properties so it matches RIFSC
	- Add missing "feature-domain-controller" property

 .../bindings/bus/st,stm32-etzpc.yaml          | 96 +++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml

diff --git a/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml b/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
new file mode 100644
index 000000000000..ef5979c0d6f2
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bus/st,stm32-etzpc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STM32 Extended TrustZone protection controller
+
+description: |
+  The ETZPC configures TrustZone security in a SoC having bus masters and
+  devices with programmable-security attributes (securable resources).
+
+maintainers:
+  - Gatien Chevallier <gatien.chevallier@foss.st.com>
+
+properties:
+  compatible:
+    contains:
+      const: st,stm32-etzpc
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  ranges: true
+
+  "#feature-domain-cells":
+    const: 1
+
+  feature-domain-controller: true
+
+patternProperties:
+  "^.*@[0-9a-f]+$":
+    description: Peripherals
+    type: object
+    properties:
+      feature-domains:
+        minItems: 1
+        description:
+          The phandle of the firewall controller of the peripheral and the
+          platform-specific firewall ID of the peripheral.
+
+      feature-domain-names:
+        minItems: 1
+
+    required:
+      - feature-domains
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - feature-domain-controller
+  - "#feature-domain-cells"
+  - ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    // In this example, the usart2 device refers to rifsc as its domain
+    // controller.
+    // Access rights are verified before creating devices.
+
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/stm32mp13-clks.h>
+    #include <dt-bindings/reset/stm32mp13-resets.h>
+
+    etzpc: bus@5c007000 {
+        compatible = "st,stm32-etzpc";
+        reg = <0x5c007000 0x400>;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        feature-domain-controller;
+        #feature-domain-cells = <1>;
+        ranges;
+
+        usart2: serial@4c001000 {
+            compatible = "st,stm32h7-uart";
+            reg = <0x4c001000 0x400>;
+            interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&rcc USART2_K>;
+            resets = <&rcc USART2_R>;
+            wakeup-source;
+            dmas = <&dmamux1 43 0x400 0x5>,
+                    <&dmamux1 44 0x400 0x1>;
+            dma-names = "rx", "tx";
+            feature-domains = <&etzpc 17>;
+        };
+    };
-- 
2.25.1

[PATCH v3 05/11] firewall: introduce stm32_firewall framework

[Gatien Chevallier]

Introduce a STM32 firewall framework that offers to firewall consumers
different firewall services such as the ability to check their access
rights against their firewall controller(s).

The STM32 firewall framework offers a generic API for STM32 firewall
controllers that is defined in their drivers to best fit the
specificity of each firewall.

There are various types of firewalls:
-Peripheral firewalls that filter accesses to peripherals
-Memory firewalls that filter accesses to memories or memory regions
-No type for undefined type of firewall

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2:
	- Support multiple entries for "feature-domains"
	  property. Change stm32_firewall_get_firewall()
	  to do so.
	- Better handle the device-tree parsing using
	  phandle+args APIs and phandle iterator.
	- Remove "resource firewall" type
	- Rephrase STM32_FIREWALL description in the bus
	  Kconfig and remove useless default value
	- Add missing EXPORT_SYMBOL_GPL
	- Remove useless stm32_firewall_get_id() API
	- Add a field for the name of the firewall entry
	  in the stm32_firewall_controller structure
	- Minor fixes on some traces level (err -> debug)
	- Fix licenses to GPL-2.0-only
	- Fix stm32_firewall_get_firewall() description
	- Rephrase some sentences to better emphasize this
	  is STM32-specific
	- Switch to list_for_each_entry() in
	  stm32_firewall_controller_unregister() as we only
	  expect one firewall controller instance per device.
	  The loop just breaks when found
	- Do not register the firewall controller if it is
	  already registered to the framework

 MAINTAINERS                               |   5 +
 arch/arm64/Kconfig.platforms              |   1 +
 drivers/bus/Kconfig                       |   9 +
 drivers/bus/Makefile                      |   1 +
 drivers/bus/stm32_firewall.c              | 288 ++++++++++++++++++++++
 drivers/bus/stm32_firewall.h              |  83 +++++++
 include/linux/bus/stm32_firewall_device.h | 140 +++++++++++
 7 files changed, 527 insertions(+)
 create mode 100644 drivers/bus/stm32_firewall.c
 create mode 100644 drivers/bus/stm32_firewall.h
 create mode 100644 include/linux/bus/stm32_firewall_device.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d516295978a4..17559ed17a11 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -20137,6 +20137,11 @@ T:	git git://linuxtv.org/media_tree.git
 F:	Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml
 F:	drivers/media/i2c/st-mipid02.c
 
+ST STM32 FIREWALL
+M:	Gatien Chevallier <gatien.chevallier@foss.st.com>
+S:	Maintained
+F:	drivers/bus/stm32_firewall.c
+
 ST STM32 I2C/SMBUS DRIVER
 M:	Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
 M:	Alain Volmat <alain.volmat@foss.st.com>
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 6069120199bb..5a46e90f1e4e 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -293,6 +293,7 @@ config ARCH_STM32
 	select ARM_SMC_MBOX
 	select ARM_SCMI_PROTOCOL
 	select COMMON_CLK_SCMI
+	select STM32_FIREWALL
 	help
 	  This enables support for ARMv8 based STMicroelectronics
 	  STM32 family, including:
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index fcfa280df98a..7ac904363a28 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -163,6 +163,15 @@ config QCOM_SSC_BLOCK_BUS
 	  i2c/spi/uart controllers, a hexagon core, and a clock controller
 	  which provides clocks for the above.
 
+config STM32_FIREWALL
+	bool "STM32 Firewall framework"
+	depends on ARCH_STM32 || COMPILE_TEST
+	help
+	  Say y to enable STM32 firewall framework and its services. Firewall
+	  controllers will be able to register to the framework. Access for
+	  hardware resources linked to a firewall controller can be requested
+	  through this STM32 framework.
+
 config SUN50I_DE2_BUS
 	bool "Allwinner A64 DE2 Bus Driver"
 	  default ARM64
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index d90eed189a65..fc0511450ec2 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_QCOM_EBI2)		+= qcom-ebi2.o
 obj-$(CONFIG_QCOM_SSC_BLOCK_BUS)	+= qcom-ssc-block-bus.o
+obj-$(CONFIG_STM32_FIREWALL)	+= stm32_firewall.o
 obj-$(CONFIG_SUN50I_DE2_BUS)	+= sun50i-de2.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_OF)		+= simple-pm-bus.o
diff --git a/drivers/bus/stm32_firewall.c b/drivers/bus/stm32_firewall.c
new file mode 100644
index 000000000000..4a8e44b732b1
--- /dev/null
+++ b/drivers/bus/stm32_firewall.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023, STMicroelectronics - All Rights Reserved
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/bus/stm32_firewall_device.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+
+#include "stm32_firewall.h"
+
+/* Corresponds to STM32_FIREWALL_MAX_EXTRA_ARGS + firewall ID */
+#define STM32_FIREWALL_MAX_ARGS		(STM32_FIREWALL_MAX_EXTRA_ARGS + 1)
+
+static LIST_HEAD(firewall_controller_list);
+static DEFINE_MUTEX(firewall_controller_list_lock);
+
+/* Firewall device API */
+
+int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall,
+				unsigned int nb_firewall)
+{
+	struct stm32_firewall_controller *ctrl;
+	struct of_phandle_iterator it;
+	unsigned int i, j = 0;
+	int err;
+
+	if (!firewall || !nb_firewall)
+		return -EINVAL;
+
+	/* Parse property with phandle parsed out */
+	of_for_each_phandle(&it, err, np, "feature-domains", "#feature-domain-cells", 0) {
+		struct of_phandle_args provider_args;
+		struct device_node *provider = it.node;
+		const char *fw_entry;
+		bool match = false;
+
+		if (err) {
+			pr_err("Unable to get feature-domains property for node %s\n, err: %d",
+			       np->full_name, err);
+			of_node_put(provider);
+			return err;
+		}
+
+		if (j > nb_firewall) {
+			pr_err("Too many firewall controllers");
+			of_node_put(provider);
+			return -EINVAL;
+		}
+
+		provider_args.args_count = of_phandle_iterator_args(&it, provider_args.args,
+								    STM32_FIREWALL_MAX_ARGS);
+
+		/* Check if the parsed phandle corresponds to a registered firewall controller */
+		mutex_lock(&firewall_controller_list_lock);
+		list_for_each_entry(ctrl, &firewall_controller_list, entry) {
+			if (ctrl->dev->of_node->phandle == it.phandle) {
+				match = true;
+				firewall[j].firewall_ctrl = ctrl;
+				break;
+			}
+		}
+		mutex_unlock(&firewall_controller_list_lock);
+
+		if (!match) {
+			firewall[j].firewall_ctrl = NULL;
+			pr_err("No firewall controller registered for %s\n", np->full_name);
+			of_node_put(provider);
+			return -ENODEV;
+		}
+
+		err = of_property_read_string_index(np, "feature-domain-names", j, &fw_entry);
+		if (err == 0)
+			firewall[j].entry = fw_entry;
+
+		/* Handle the case when there are no arguments given along with the phandle */
+		if (provider_args.args_count < 0 ||
+		    provider_args.args_count > STM32_FIREWALL_MAX_ARGS) {
+			of_node_put(provider);
+			return -EINVAL;
+		} else if (provider_args.args_count == 0) {
+			firewall[j].extra_args_size = 0;
+			firewall[j].firewall_id = U32_MAX;
+			j++;
+			continue;
+		}
+
+		/* The firewall ID is always the first argument */
+		firewall[j].firewall_id = provider_args.args[0];
+
+		/* Extra args start at the third argument */
+		for (i = 0; i < provider_args.args_count; i++)
+			firewall[j].extra_args[i] = provider_args.args[i + 1];
+
+		/* Remove the firewall ID arg that is not an extra argument */
+		firewall[j].extra_args_size = provider_args.args_count - 1;
+
+		j++;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_get_firewall);
+
+int stm32_firewall_grant_access(struct stm32_firewall *firewall)
+{
+	struct stm32_firewall_controller *firewall_controller;
+
+	if (!firewall || firewall->firewall_id == U32_MAX)
+		return -EINVAL;
+
+	firewall_controller = firewall->firewall_ctrl;
+
+	if (!firewall_controller)
+		return -ENODEV;
+
+	return firewall_controller->grant_access(firewall_controller, firewall->firewall_id);
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_grant_access);
+
+int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id)
+{
+	struct stm32_firewall_controller *firewall_controller;
+
+	if (!firewall || subsystem_id == U32_MAX || firewall->firewall_id == U32_MAX)
+		return -EINVAL;
+
+	firewall_controller = firewall->firewall_ctrl;
+
+	if (!firewall_controller)
+		return -ENODEV;
+
+	return firewall_controller->grant_access(firewall_controller, subsystem_id);
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_grant_access_by_id);
+
+void stm32_firewall_release_access(struct stm32_firewall *firewall)
+{
+	struct stm32_firewall_controller *firewall_controller;
+
+	if (!firewall || firewall->firewall_id == U32_MAX) {
+		pr_debug("Incorrect arguments when releasing a firewall access\n");
+		return;
+	}
+
+	firewall_controller = firewall->firewall_ctrl;
+
+	if (!firewall_controller) {
+		pr_debug("No firewall controller to release\n");
+		return;
+	}
+
+	firewall_controller->release_access(firewall_controller, firewall->firewall_id);
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_release_access);
+
+void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id)
+{
+	struct stm32_firewall_controller *firewall_controller;
+
+	if (!firewall || subsystem_id == U32_MAX || firewall->firewall_id == U32_MAX) {
+		pr_debug("Incorrect arguments when releasing a firewall access");
+		return;
+	}
+
+	firewall_controller = firewall->firewall_ctrl;
+
+	if (!firewall_controller) {
+		pr_debug("No firewall controller to release");
+		return;
+	}
+
+	firewall_controller->release_access(firewall_controller, subsystem_id);
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_release_access_by_id);
+
+/* Firewall controller API */
+
+int stm32_firewall_controller_register(struct stm32_firewall_controller *firewall_controller)
+{
+	struct stm32_firewall_controller *ctrl;
+
+	pr_info("Registering %s firewall controller\n", firewall_controller->name);
+
+	if (!firewall_controller)
+		return -ENODEV;
+
+	mutex_lock(&firewall_controller_list_lock);
+	list_for_each_entry(ctrl, &firewall_controller_list, entry) {
+		if (ctrl == firewall_controller) {
+			pr_debug("%s firewall controller already registered\n",
+				 firewall_controller->name);
+			mutex_unlock(&firewall_controller_list_lock);
+			return 0;
+		}
+	}
+	list_add_tail(&firewall_controller->entry, &firewall_controller_list);
+	mutex_unlock(&firewall_controller_list_lock);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_controller_register);
+
+void stm32_firewall_controller_unregister(struct stm32_firewall_controller *firewall_controller)
+{
+	struct stm32_firewall_controller *ctrl;
+	bool controller_removed = false;
+
+	if (!firewall_controller) {
+		pr_debug("Null reference while unregistering firewall controller\n");
+		return;
+	}
+
+	mutex_lock(&firewall_controller_list_lock);
+	list_for_each_entry(ctrl, &firewall_controller_list, entry) {
+		if (ctrl == firewall_controller) {
+			controller_removed = true;
+			list_del_init(&ctrl->entry);
+			break;
+		}
+	}
+	mutex_unlock(&firewall_controller_list_lock);
+
+	if (!controller_removed)
+		pr_debug("There was no firewall controller named %s to unregister\n",
+			 firewall_controller->name);
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_controller_unregister);
+
+int stm32_firewall_populate_bus(struct stm32_firewall_controller *firewall_controller)
+{
+	struct stm32_firewall *firewalls;
+	struct device_node *child;
+	struct device *parent;
+	unsigned int i;
+	int len;
+	int err;
+
+	parent = firewall_controller->dev;
+
+	dev_dbg(parent, "Populating %s system bus\n", dev_name(firewall_controller->dev));
+
+	for_each_available_child_of_node(dev_of_node(parent), child) {
+		/* The feature-domains property is mandatory for firewall bus devices */
+		len = of_count_phandle_with_args(child, "feature-domains", "#feature-domain-cells");
+		if (len <= 0)
+			return -EINVAL;
+
+		firewalls = kcalloc(len, sizeof(*firewalls), GFP_KERNEL);
+		if (!firewalls)
+			return -ENOMEM;
+
+		err = stm32_firewall_get_firewall(child, firewalls, (unsigned int)len);
+		if (err) {
+			kfree(firewalls);
+			return err;
+		}
+
+		for (i = 0; i < len; i++) {
+			if (firewall_controller->grant_access(firewall_controller,
+							      firewalls[i].firewall_id)) {
+				/*
+				 * Peripheral access not allowed or not defined.
+				 * Mark the node as populated so platform bus won't probe it
+				 */
+				of_node_set_flag(child, OF_POPULATED);
+				dev_err(parent, "%s: Device driver will not be probed\n",
+					child->full_name);
+			}
+		}
+
+		kfree(firewalls);
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(stm32_firewall_populate_bus);
diff --git a/drivers/bus/stm32_firewall.h b/drivers/bus/stm32_firewall.h
new file mode 100644
index 000000000000..eed089a0acc0
--- /dev/null
+++ b/drivers/bus/stm32_firewall.h
@@ -0,0 +1,83 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2023, STMicroelectronics - All Rights Reserved
+ */
+
+#ifndef _STM32_FIREWALL_H
+#define _STM32_FIREWALL_H
+
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+/**
+ * STM32_PERIPHERAL_FIREWALL:		This type of firewall protects peripherals
+ * STM32_MEMORY_FIREWALL:		This type of firewall protects memories/subsets of memory
+ *					zones
+ * STM32_NOTYPE_FIREWALL:		Undefined firewall type
+ */
+
+#define STM32_PERIPHERAL_FIREWALL	BIT(1)
+#define STM32_MEMORY_FIREWALL		BIT(2)
+#define STM32_NOTYPE_FIREWALL		BIT(3)
+
+/**
+ * struct stm32_firewall_controller - Information on firewall controller supplying services
+ *
+ * @name			Name of the firewall controller
+ * @dev				Device reference of the firewall controller
+ * @mmio			Base address of the firewall controller
+ * @entry			List entry of the firewall controller list
+ * @type			Type of firewall
+ * @max_entries			Number of entries covered by the firewall
+ * @grant_access		Callback used to grant access for a device access against a
+ *				firewall controller
+ * @release_access		Callback used to release resources taken by a device when access was
+ *				granted
+ * @grant_memory_range_access	Callback used to grant access for a device to a given memory region
+ */
+struct stm32_firewall_controller {
+	const char *name;
+	struct device *dev;
+	void __iomem *mmio;
+	struct list_head entry;
+	unsigned int type;
+	unsigned int max_entries;
+
+	int (*grant_access)(struct stm32_firewall_controller *ctrl, u32 id);
+	void (*release_access)(struct stm32_firewall_controller *ctrl, u32 id);
+	int (*grant_memory_range_access)(struct stm32_firewall_controller *ctrl, phys_addr_t paddr,
+					 size_t size);
+};
+
+/**
+ * int stm32_firewall_controller_register - Register a firewall controller to the STM32 firewall
+ *					    framework
+ * @firewall_controller		Firewall controller to register
+ *
+ * Returns 0 in case of success or -ENODEV if no controller was given.
+ */
+int stm32_firewall_controller_register(struct stm32_firewall_controller *firewall_controller);
+
+/**
+ * int stm32_firewall_controller_unregister - Unregister a firewall controller from the STM32
+ *					      firewall framework
+ * @firewall_controller		Firewall controller to unregister
+ */
+void stm32_firewall_controller_unregister(struct stm32_firewall_controller *firewall_controller);
+
+/**
+ * stm32_firewall_populate_bus - Populate device tree nodes that have a correct firewall
+ *				 configuration. This is used at boot-time only, as a sanity check
+ *				 between device tree and firewalls hardware configurations to
+ *				 prevent a kernel crash when a device driver is not granted access
+ *
+ * @firewall_controller		Firewall controller which nodes will be populated or not
+ *
+ * Returns 0 in case of success or appropriate errno code if error occurred.
+ */
+int stm32_firewall_populate_bus(struct stm32_firewall_controller *firewall_controller);
+
+#endif /* _STM32_FIREWALL_H */
diff --git a/include/linux/bus/stm32_firewall_device.h b/include/linux/bus/stm32_firewall_device.h
new file mode 100644
index 000000000000..9bdc4060154c
--- /dev/null
+++ b/include/linux/bus/stm32_firewall_device.h
@@ -0,0 +1,140 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2023, STMicroelectronics - All Rights Reserved
+ */
+
+#ifndef STM32_FIREWALL_DEVICE_H
+#define STM32_FIREWALL_DEVICE_H
+
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#define STM32_FIREWALL_MAX_EXTRA_ARGS		5
+
+/* Opaque reference to stm32_firewall_controller */
+struct stm32_firewall_controller;
+
+/**
+ * stm32_firewall - Information on a device's firewall. Each device can have more than one firewall.
+ *
+ * @firewall_ctrl		Pointer referencing a firewall controller of the device. It is
+ *				opaque so a device cannot manipulate the controller's ops or access
+ *				the controller's data
+ * @extra_args			Extra arguments that are implementation dependent
+ * @entry			Name of the firewall entry
+ * @extra_args_size		Number of extra arguments
+ * @firewall_id			Firewall ID associated the device for this firewall controller
+ */
+struct stm32_firewall {
+	struct stm32_firewall_controller *firewall_ctrl;
+	u32 extra_args[STM32_FIREWALL_MAX_EXTRA_ARGS];
+	const char *entry;
+	size_t extra_args_size;
+	u32 firewall_id;
+};
+
+#if IS_ENABLED(CONFIG_STM32_FIREWALL)
+/**
+ * stm32_firewall_get_firewall - Get the firewall(s) associated to given device.
+ *				 The firewall controller reference is always the first argument
+ *				 of each of the feature-domains property entries.
+ *				 The firewall ID is always the second argument of each of the
+ *				 feature-domains property entries.
+ *				 If there's no argument linked to the phandle, then the firewall ID
+ *				 field is set to U32_MAX, which is an invalid ID.
+ *
+ * @np				Device node to parse
+ * @firewall			Array of firewall references
+ * @nb_firewall			Number of firewall references to get. Must be at least 1.
+ *
+ * Returns 0 on success, -ENODEV if there's no match with a firewall controller or appropriate errno
+ * code if error occurred.
+ */
+int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall,
+				unsigned int nb_firewall);
+
+/**
+ * stm32_firewall_grant_access - Request firewall access rights and grant access.
+ *
+ * @firewall			Firewall reference containing the ID to check against its firewall
+ *				controller
+ *
+ * Returns 0 if access is granted, -EACCES if access is denied, -ENODEV if firewall is null or
+ * appropriate errno code if error occurred
+ */
+int stm32_firewall_grant_access(struct stm32_firewall *firewall);
+
+/**
+ * stm32_firewall_release_access - Release access granted from a call to
+ *				   stm32_firewall_grant_access().
+ *
+ * @firewall			Firewall reference containing the ID to check against its firewall
+ *				controller
+ */
+void stm32_firewall_release_access(struct stm32_firewall *firewall);
+
+/**
+ * stm32_firewall_grant_access_by_id - Request firewall access rights of a given device
+ *				       based on a specific firewall ID
+ *
+ * Warnings:
+ * There is no way to ensure that the given ID will correspond to the firewall referenced in the
+ * device node if the ID did not come from stm32_firewall_get_firewall(). In that case, this
+ * function must be used with caution.
+ * This function should be used for subsystem resources that do not have the same firewall ID
+ * as their parent.
+ * U32_MAX is an invalid ID.
+ *
+ * @firewall			Firewall reference containing the firewall controller
+ * @subsystem_id		Firewall ID of the subsystem resource
+ *
+ * Returns 0 if access is granted, -EACCES if access is denied, -ENODEV if firewall is null or
+ * appropriate errno code if error occurred
+ */
+int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id);
+
+/**
+ * stm32_firewall_release_access_by_id - Release access granted from a call to
+ *					 stm32_firewall_grant_access_by_id().
+ *
+ * Warnings:
+ * There is no way to ensure that the given ID will correspond to the firewall referenced in the
+ * device node if the ID did not come from stm32_firewall_get_firewall(). In that case, this
+ * function must be used with caution.
+ * This function should be used for subsystem resources that do not have the same firewall ID
+ * as their parent.
+ * U32_MAX is an invalid ID.
+ *
+ * @firewall			Firewall reference containing the firewall controller
+ * @subsystem_id		Firewall ID of the subsystem resource
+ */
+void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id);
+
+#else /* CONFIG_STM32_FIREWALL */
+
+int stm32_firewall_get_firewall(struct device_node *np, struct stm32_firewall *firewall)
+{
+	return -ENODEV;
+}
+
+int stm32_firewall_grant_access(struct stm32_firewall *firewall)
+{
+	return -ENODEV;
+}
+
+void stm32_firewall_release_access(struct stm32_firewall *firewall)
+{
+}
+
+int stm32_firewall_grant_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id)
+{
+	return -ENODEV;
+}
+
+void stm32_firewall_release_access_by_id(struct stm32_firewall *firewall, u32 subsystem_id)
+{
+}
+
+#endif /* CONFIG_STM32_FIREWALL */
+#endif /* STM32_FIREWALL_DEVICE_H */
-- 
2.25.1

[PATCH v3 06/11] of: property: fw_devlink: Add support for "feature-domains"

[Gatien Chevallier]

Allows tracking dependencies between devices and their feature domain
controller.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Patch not present in V1

 drivers/of/property.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/of/property.c b/drivers/of/property.c
index ddc75cd50825..48256a865539 100644
--- a/drivers/of/property.c
+++ b/drivers/of/property.c
@@ -1266,6 +1266,7 @@ DEFINE_SIMPLE_PROP(pwms, "pwms", "#pwm-cells")
 DEFINE_SIMPLE_PROP(resets, "resets", "#reset-cells")
 DEFINE_SIMPLE_PROP(leds, "leds", NULL)
 DEFINE_SIMPLE_PROP(backlight, "backlight", NULL)
+DEFINE_SIMPLE_PROP(feature_domains, "feature-domains", "#feature-domain-cells")
 DEFINE_SUFFIX_PROP(regulators, "-supply", NULL)
 DEFINE_SUFFIX_PROP(gpio, "-gpio", "#gpio-cells")
 
@@ -1359,6 +1360,7 @@ static const struct supplier_bindings of_supplier_bindings[] = {
 	{ .parse_prop = parse_regulators, },
 	{ .parse_prop = parse_gpio, },
 	{ .parse_prop = parse_gpios, },
+	{ .parse_prop = parse_feature_domains, },
 	{}
 };
 
-- 
2.25.1

[PATCH v3 07/11] bus: rifsc: introduce RIFSC firewall controller driver

[Gatien Chevallier]

RIFSC is a peripheral firewall controller that filter accesses based on
Arm TrustZone secure state, Arm CPU privilege execution level and
Compartment IDentification of the STM32 SoC subsystems.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2:
	- Add controller name
	- Driver is now a module_platform_driver
	- Use error code returned by stm32_firewall_populate_bus()
	- Fix license

 MAINTAINERS               |   1 +
 drivers/bus/Makefile      |   2 +-
 drivers/bus/stm32_rifsc.c | 252 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 254 insertions(+), 1 deletion(-)
 create mode 100644 drivers/bus/stm32_rifsc.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 17559ed17a11..9dcf69a9e30c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -20141,6 +20141,7 @@ ST STM32 FIREWALL
 M:	Gatien Chevallier <gatien.chevallier@foss.st.com>
 S:	Maintained
 F:	drivers/bus/stm32_firewall.c
+F:	drivers/bus/stm32_rifsc.c
 
 ST STM32 I2C/SMBUS DRIVER
 M:	Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index fc0511450ec2..e50d18e1d141 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -26,7 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_QCOM_EBI2)		+= qcom-ebi2.o
 obj-$(CONFIG_QCOM_SSC_BLOCK_BUS)	+= qcom-ssc-block-bus.o
-obj-$(CONFIG_STM32_FIREWALL)	+= stm32_firewall.o
+obj-$(CONFIG_STM32_FIREWALL)	+= stm32_firewall.o stm32_rifsc.o
 obj-$(CONFIG_SUN50I_DE2_BUS)	+= sun50i-de2.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_OF)		+= simple-pm-bus.o
diff --git a/drivers/bus/stm32_rifsc.c b/drivers/bus/stm32_rifsc.c
new file mode 100644
index 000000000000..e3f67cf317de
--- /dev/null
+++ b/drivers/bus/stm32_rifsc.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023, STMicroelectronics - All Rights Reserved
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#include "stm32_firewall.h"
+
+/*
+ * RIFSC offset register
+ */
+#define RIFSC_RISC_SECCFGR0		0x10
+#define RIFSC_RISC_PRIVCFGR0		0x30
+#define RIFSC_RISC_PER0_CIDCFGR		0x100
+#define RIFSC_RISC_PER0_SEMCR		0x104
+#define RIFSC_RISC_HWCFGR2		0xFEC
+
+/*
+ * SEMCR register
+ */
+#define SEMCR_MUTEX			BIT(0)
+
+/*
+ * HWCFGR2 register
+ */
+#define HWCFGR2_CONF1_MASK		GENMASK(15, 0)
+#define HWCFGR2_CONF2_MASK		GENMASK(23, 16)
+#define HWCFGR2_CONF3_MASK		GENMASK(31, 24)
+
+/*
+ * RIFSC miscellaneous
+ */
+#define RIFSC_RISC_CFEN_MASK		BIT(0)
+#define RIFSC_RISC_SEM_EN_MASK		BIT(1)
+#define RIFSC_RISC_SCID_MASK		GENMASK(6, 4)
+#define RIFSC_RISC_SEML_SHIFT		16
+#define RIFSC_RISC_SEMWL_MASK		GENMASK(23, 16)
+#define RIFSC_RISC_PER_ID_MASK		GENMASK(31, 24)
+
+#define RIFSC_RISC_PERx_CID_MASK	(RIFSC_RISC_CFEN_MASK | \
+					 RIFSC_RISC_SEM_EN_MASK | \
+					 RIFSC_RISC_SCID_MASK | \
+					 RIFSC_RISC_SEMWL_MASK)
+
+#define IDS_PER_RISC_SEC_PRIV_REGS	32
+
+/* RIF miscellaneous */
+/*
+ * CIDCFGR register fields
+ */
+#define CIDCFGR_CFEN			BIT(0)
+#define CIDCFGR_SEMEN			BIT(1)
+#define CIDCFGR_SEMWL(x)		BIT(RIFSC_RISC_SEML_SHIFT + (x))
+
+#define SEMWL_SHIFT			16
+
+/* Compartiment IDs */
+#define RIF_CID0			0x0
+#define RIF_CID1			0x1
+
+static bool stm32_rifsc_is_semaphore_available(void __iomem *addr)
+{
+	return !(readl(addr) & SEMCR_MUTEX);
+}
+
+static int stm32_rif_acquire_semaphore(struct stm32_firewall_controller *stm32_firewall_controller,
+				       int id)
+{
+	void __iomem *addr = stm32_firewall_controller->mmio + RIFSC_RISC_PER0_SEMCR + 0x8 * id;
+
+	__set_bit(SEMCR_MUTEX, addr);
+
+	/* Check that CID1 has the semaphore */
+	if (stm32_rifsc_is_semaphore_available(addr) ||
+	    FIELD_GET(RIFSC_RISC_SCID_MASK, readl(addr)) != RIF_CID1)
+		return -EACCES;
+
+	return 0;
+}
+
+static void stm32_rif_release_semaphore(struct stm32_firewall_controller *stm32_firewall_controller,
+					int id)
+{
+	void __iomem *addr = stm32_firewall_controller->mmio + RIFSC_RISC_PER0_SEMCR + 0x8 * id;
+
+	if (stm32_rifsc_is_semaphore_available(addr))
+		return;
+
+	writel(SEMCR_MUTEX, addr);
+
+	/* Ok if another compartment takes the semaphore before the check */
+	WARN_ON(!stm32_rifsc_is_semaphore_available(addr) &&
+		FIELD_GET(RIFSC_RISC_SCID_MASK, readl(addr)) == RIF_CID1);
+}
+
+static int stm32_rifsc_grant_access(struct stm32_firewall_controller *ctrl, u32 firewall_id)
+{
+	struct stm32_firewall_controller *rifsc_controller = ctrl;
+	u32 reg_offset, reg_id, sec_reg_value, cid_reg_value;
+	int rc;
+
+	if (firewall_id >= rifsc_controller->max_entries) {
+		dev_err(rifsc_controller->dev, "Invalid sys bus ID %u", firewall_id);
+		return -EINVAL;
+	}
+
+	/*
+	 * RIFSC_RISC_PRIVCFGRx and RIFSC_RISC_SECCFGRx both handle configuration access for
+	 * 32 peripherals. On the other hand, there is one _RIFSC_RISC_PERx_CIDCFGR register
+	 * per peripheral
+	 */
+	reg_id = firewall_id / IDS_PER_RISC_SEC_PRIV_REGS;
+	reg_offset = firewall_id % IDS_PER_RISC_SEC_PRIV_REGS;
+	sec_reg_value = readl(rifsc_controller->mmio + RIFSC_RISC_SECCFGR0 + 0x4 * reg_id);
+	cid_reg_value = readl(rifsc_controller->mmio + RIFSC_RISC_PER0_CIDCFGR + 0x8 * firewall_id);
+
+	/* First check conditions for semaphore mode, which doesn't take into account static CID. */
+	if ((cid_reg_value & CIDCFGR_SEMEN) && (cid_reg_value & CIDCFGR_CFEN)) {
+		if (cid_reg_value & BIT(RIF_CID1 + SEMWL_SHIFT)) {
+			/* Static CID is irrelevant if semaphore mode */
+			goto skip_cid_check;
+		} else {
+			dev_dbg(rifsc_controller->dev,
+				"Invalid bus semaphore configuration: index %d\n", firewall_id);
+			return -EACCES;
+		}
+	}
+
+	/*
+	 * Skip CID check if CID filtering isn't enabled or filtering is enabled on CID0, which
+	 * corresponds to whatever CID.
+	 */
+	if (!(cid_reg_value & CIDCFGR_CFEN) ||
+	    FIELD_GET(RIFSC_RISC_SCID_MASK, cid_reg_value) == RIF_CID0)
+		goto skip_cid_check;
+
+	/* Coherency check with the CID configuration */
+	if (FIELD_GET(RIFSC_RISC_SCID_MASK, cid_reg_value) != RIF_CID1) {
+		dev_dbg(rifsc_controller->dev, "Invalid CID configuration for peripheral: %d\n",
+			firewall_id);
+		return -EACCES;
+	}
+
+skip_cid_check:
+	/* Check security configuration */
+	if (sec_reg_value & BIT(reg_offset)) {
+		dev_dbg(rifsc_controller->dev,
+			"Invalid security configuration for peripheral: %d\n", firewall_id);
+		return -EACCES;
+	}
+
+	/*
+	 * If the peripheral is in semaphore mode, take the semaphore so that
+	 * the CID1 has the ownership.
+	 */
+	if ((cid_reg_value & CIDCFGR_SEMEN) && (cid_reg_value & CIDCFGR_CFEN)) {
+		rc = stm32_rif_acquire_semaphore(rifsc_controller, firewall_id);
+		if (rc) {
+			dev_err(rifsc_controller->dev,
+				"Couldn't acquire semaphore for peripheral: %d\n", firewall_id);
+			return rc;
+		}
+	}
+
+	return 0;
+}
+
+static void stm32_rifsc_release_access(struct stm32_firewall_controller *ctrl, u32 firewall_id)
+{
+	stm32_rif_release_semaphore(ctrl, firewall_id);
+}
+
+static int stm32_rifsc_probe(struct platform_device *pdev)
+{
+	struct stm32_firewall_controller *rifsc_controller;
+	struct device_node *np = pdev->dev.of_node;
+	u32 nb_risup, nb_rimu, nb_risal;
+	struct resource *res;
+	void __iomem *mmio;
+	int rc;
+
+	rifsc_controller = devm_kzalloc(&pdev->dev, sizeof(*rifsc_controller), GFP_KERNEL);
+	if (!rifsc_controller)
+		return -ENOMEM;
+
+	mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(mmio))
+		return PTR_ERR(mmio);
+
+	rifsc_controller->dev = &pdev->dev;
+	rifsc_controller->mmio = mmio;
+	rifsc_controller->name = dev_driver_string(rifsc_controller->dev);
+	rifsc_controller->type = STM32_PERIPHERAL_FIREWALL | STM32_MEMORY_FIREWALL;
+	rifsc_controller->grant_access = stm32_rifsc_grant_access;
+	rifsc_controller->release_access = stm32_rifsc_release_access;
+
+	/* Get number of RIFSC entries*/
+	nb_risup = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF1_MASK;
+	nb_rimu = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF2_MASK;
+	nb_risal = readl(rifsc_controller->mmio + RIFSC_RISC_HWCFGR2) & HWCFGR2_CONF3_MASK;
+	rifsc_controller->max_entries = nb_risup + nb_rimu + nb_risal;
+
+	platform_set_drvdata(pdev, rifsc_controller);
+
+	rc = stm32_firewall_controller_register(rifsc_controller);
+	if (rc) {
+		dev_err(rifsc_controller->dev, "Couldn't register as a firewall controller: %d",
+			rc);
+		return rc;
+	}
+
+	rc = stm32_firewall_populate_bus(rifsc_controller);
+	if (rc) {
+		dev_err(rifsc_controller->dev, "Couldn't populate RIFSC bus: %d",
+			rc);
+		return rc;
+	}
+
+	/* Populate all allowed nodes */
+	return of_platform_populate(np, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id stm32_rifsc_of_match[] = {
+	{ .compatible = "st,stm32mp25-rifsc" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, stm32_rifsc_of_match);
+
+static struct platform_driver stm32_rifsc_driver = {
+	.probe  = stm32_rifsc_probe,
+	.driver = {
+		.name = "stm32-rifsc",
+		.of_match_table = stm32_rifsc_of_match,
+	},
+};
+module_platform_driver(stm32_rifsc_driver);
+
+MODULE_AUTHOR("Gatien Chevallier <gatien.chevallier@foss.st.com>");
+MODULE_DESCRIPTION("STMicroelectronics RIFSC driver");
+MODULE_LICENSE("GPL");
-- 
2.25.1

[PATCH v3 08/11] arm64: dts: st: add RIFSC as a domain controller for STM32MP25x boards

[Gatien Chevallier]

RIFSC is a firewall controller. Change its compatible so that is matches
the documentation and reference RIFSC as a feature-domain-controller.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2:
	- Fix rifsc node name
	- Move the "ranges" property under the
	  "feature-domains" one

 arch/arm64/boot/dts/st/stm32mp251.dtsi | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/st/stm32mp251.dtsi b/arch/arm64/boot/dts/st/stm32mp251.dtsi
index 5268a4321841..cb084381e4cd 100644
--- a/arch/arm64/boot/dts/st/stm32mp251.dtsi
+++ b/arch/arm64/boot/dts/st/stm32mp251.dtsi
@@ -105,11 +105,13 @@ soc@0 {
 		interrupt-parent = <&intc>;
 		ranges = <0x0 0x0 0x0 0x80000000>;
 
-		rifsc: rifsc-bus@42080000 {
-			compatible = "simple-bus";
+		rifsc: bus@42080000 {
+			compatible = "st,stm32mp25-rifsc";
 			reg = <0x42080000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+			feature-domain-controller;
+			#feature-domain-cells = <1>;
 			ranges;
 
 			usart2: serial@400e0000 {
@@ -117,6 +119,7 @@ usart2: serial@400e0000 {
 				reg = <0x400e0000 0x400>;
 				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&ck_flexgen_08>;
+				feature-domains = <&rifsc 32>;
 				status = "disabled";
 			};
 		};
-- 
2.25.1

[PATCH v3 09/11] bus: etzpc: introduce ETZPC firewall controller driver

[Gatien Chevallier]

ETZPC is a peripheral and memory firewall controller that filter accesses
based on Arm TrustZone secure state and Arm CPU privilege execution level.
It handles MCU isolation as well.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---

Changes in V2:
	- Add controller name
	- Driver is now a module_platform_driver
	- Use error code returned by stm32_firewall_populate_bus()
	- Fix license

 MAINTAINERS               |   1 +
 drivers/bus/Makefile      |   2 +-
 drivers/bus/stm32_etzpc.c | 141 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 143 insertions(+), 1 deletion(-)
 create mode 100644 drivers/bus/stm32_etzpc.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 9dcf69a9e30c..a55fa36e25db 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -20140,6 +20140,7 @@ F:	drivers/media/i2c/st-mipid02.c
 ST STM32 FIREWALL
 M:	Gatien Chevallier <gatien.chevallier@foss.st.com>
 S:	Maintained
+F:	drivers/bus/stm32_etzpc.c
 F:	drivers/bus/stm32_firewall.c
 F:	drivers/bus/stm32_rifsc.c
 
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index e50d18e1d141..cddd4984d6af 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -26,7 +26,7 @@ obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_QCOM_EBI2)		+= qcom-ebi2.o
 obj-$(CONFIG_QCOM_SSC_BLOCK_BUS)	+= qcom-ssc-block-bus.o
-obj-$(CONFIG_STM32_FIREWALL)	+= stm32_firewall.o stm32_rifsc.o
+obj-$(CONFIG_STM32_FIREWALL)	+= stm32_firewall.o stm32_rifsc.o stm32_etzpc.o
 obj-$(CONFIG_SUN50I_DE2_BUS)	+= sun50i-de2.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_OF)		+= simple-pm-bus.o
diff --git a/drivers/bus/stm32_etzpc.c b/drivers/bus/stm32_etzpc.c
new file mode 100644
index 000000000000..7fc0f16960be
--- /dev/null
+++ b/drivers/bus/stm32_etzpc.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023, STMicroelectronics - All Rights Reserved
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#include "stm32_firewall.h"
+
+/*
+ * ETZPC registers
+ */
+#define ETZPC_DECPROT			0x10
+#define ETZPC_HWCFGR			0x3F0
+
+/*
+ * HWCFGR register
+ */
+#define ETZPC_HWCFGR_NUM_TZMA		GENMASK(7, 0)
+#define ETZPC_HWCFGR_NUM_PER_SEC	GENMASK(15, 8)
+#define ETZPC_HWCFGR_NUM_AHB_SEC	GENMASK(23, 16)
+#define ETZPC_HWCFGR_CHUNKS1N4		GENMASK(31, 24)
+
+/*
+ * ETZPC miscellaneous
+ */
+#define ETZPC_PROT_MASK			GENMASK(1, 0)
+#define ETZPC_PROT_A7NS			0x3
+#define ETZPC_DECPROT_SHIFT		1
+
+#define IDS_PER_DECPROT_REGS		16
+
+static int stm32_etzpc_grant_access(struct stm32_firewall_controller *ctrl, u32 firewall_id)
+{
+	u32 offset, reg_offset, sec_val;
+
+	if (firewall_id >= ctrl->max_entries) {
+		dev_err(ctrl->dev, "Invalid sys bus ID %u", firewall_id);
+		return -EINVAL;
+	}
+
+	/* Check access configuration, 16 peripherals per register */
+	reg_offset = ETZPC_DECPROT + 0x4 * (firewall_id / IDS_PER_DECPROT_REGS);
+	offset = (firewall_id % IDS_PER_DECPROT_REGS) << ETZPC_DECPROT_SHIFT;
+
+	/* Verify peripheral is non-secure and attributed to cortex A7 */
+	sec_val = (readl(ctrl->mmio + reg_offset) >> offset) & ETZPC_PROT_MASK;
+	if (sec_val != ETZPC_PROT_A7NS) {
+		dev_dbg(ctrl->dev, "Invalid bus configuration: reg_offset %#x, value %d\n",
+			reg_offset, sec_val);
+		return -EACCES;
+	}
+
+	return 0;
+}
+
+static void stm32_etzpc_release_access(struct stm32_firewall_controller *ctrl __maybe_unused,
+				       u32 firewall_id __maybe_unused)
+{
+}
+
+static int stm32_etzpc_probe(struct platform_device *pdev)
+{
+	struct stm32_firewall_controller *etzpc_controller;
+	struct device_node *np = pdev->dev.of_node;
+	u32 nb_per, nb_master;
+	struct resource *res;
+	void __iomem *mmio;
+	int rc;
+
+	etzpc_controller = devm_kzalloc(&pdev->dev, sizeof(*etzpc_controller), GFP_KERNEL);
+	if (!etzpc_controller)
+		return -ENOMEM;
+
+	mmio = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+	if (IS_ERR(mmio))
+		return PTR_ERR(mmio);
+
+	etzpc_controller->dev = &pdev->dev;
+	etzpc_controller->mmio = mmio;
+	etzpc_controller->name = dev_driver_string(etzpc_controller->dev);
+	etzpc_controller->type = STM32_PERIPHERAL_FIREWALL | STM32_MEMORY_FIREWALL;
+	etzpc_controller->grant_access = stm32_etzpc_grant_access;
+	etzpc_controller->release_access = stm32_etzpc_release_access;
+
+	/* Get number of etzpc entries*/
+	nb_per = FIELD_GET(ETZPC_HWCFGR_NUM_PER_SEC,
+			   readl(etzpc_controller->mmio + ETZPC_HWCFGR));
+	nb_master = FIELD_GET(ETZPC_HWCFGR_NUM_AHB_SEC,
+			      readl(etzpc_controller->mmio + ETZPC_HWCFGR));
+	etzpc_controller->max_entries = nb_per + nb_master;
+
+	platform_set_drvdata(pdev, etzpc_controller);
+
+	rc = stm32_firewall_controller_register(etzpc_controller);
+	if (rc) {
+		dev_err(etzpc_controller->dev, "Couldn't register as a firewall controller: %d",
+			rc);
+		return rc;
+	}
+
+	rc = stm32_firewall_populate_bus(etzpc_controller);
+	if (rc) {
+		dev_err(etzpc_controller->dev, "Couldn't populate ETZPC bus: %d",
+			rc);
+		return rc;
+	}
+
+	/* Populate all allowed nodes */
+	return of_platform_populate(np, NULL, NULL, &pdev->dev);
+}
+
+static const struct of_device_id stm32_etzpc_of_match[] = {
+	{ .compatible = "st,stm32-etzpc" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, stm32_etzpc_of_match);
+
+static struct platform_driver stm32_etzpc_driver = {
+	.probe  = stm32_etzpc_probe,
+	.driver = {
+		.name = "stm32-etzpc",
+		.of_match_table = stm32_etzpc_of_match,
+	},
+};
+module_platform_driver(stm32_etzpc_driver);
+
+MODULE_AUTHOR("Gatien Chevallier <gatien.chevallier@foss.st.com>");
+MODULE_DESCRIPTION("STMicroelectronics ETZPC driver");
+MODULE_LICENSE("GPL");
-- 
2.25.1

[PATCH v3 10/11] ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards

[Gatien Chevallier]

ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and reference ETZPC as a
feature-domain-controller.

For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP15 reference manual.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp151.dtsi  | 2757 +++++++++++++------------
 arch/arm/boot/dts/st/stm32mp153.dtsi  |   52 +-
 arch/arm/boot/dts/st/stm32mp15xc.dtsi |   19 +-
 3 files changed, 1451 insertions(+), 1377 deletions(-)

diff --git a/arch/arm/boot/dts/st/stm32mp151.dtsi b/arch/arm/boot/dts/st/stm32mp151.dtsi
index 61508917521c..764e3fc60521 100644
--- a/arch/arm/boot/dts/st/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp151.dtsi
@@ -122,1543 +122,1616 @@ soc {
 		interrupt-parent = <&intc>;
 		ranges;
 
-		timers2: timer@40000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40000000 0x400>;
-			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM2_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 18 0x400 0x1>,
-			       <&dmamux1 19 0x400 0x1>,
-			       <&dmamux1 20 0x400 0x1>,
-			       <&dmamux1 21 0x400 0x1>,
-			       <&dmamux1 22 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+		ipcc: mailbox@4c001000 {
+			compatible = "st,stm32mp1-ipcc";
+			#mbox-cells = <1>;
+			reg = <0x4c001000 0x400>;
+			st,proc-id = <0>;
+			interrupts-extended =
+				<&exti 61 1>,
+				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
+			clocks = <&rcc IPCC>;
+			wakeup-source;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@1 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <1>;
-				status = "disabled";
-			};
-
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp1-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
-		timers3: timer@40001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40001000 0x400>;
-			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM3_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 23 0x400 0x1>,
-			       <&dmamux1 24 0x400 0x1>,
-			       <&dmamux1 25 0x400 0x1>,
-			       <&dmamux1 26 0x400 0x1>,
-			       <&dmamux1 27 0x400 0x1>,
-			       <&dmamux1 28 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
-			status = "disabled";
+		pwr_regulators: pwr@50001000 {
+			compatible = "st,stm32mp1,pwr-reg";
+			reg = <0x50001000 0x10>;
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+			reg11: reg11 {
+				regulator-name = "reg11";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
 			};
 
-			timer@2 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <2>;
-				status = "disabled";
+			reg18: reg18 {
+				regulator-name = "reg18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 			};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
+			usb33: usb33 {
+				regulator-name = "usb33";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 			};
 		};
 
-		timers4: timer@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40002000 0x400>;
-			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM4_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 29 0x400 0x1>,
-			       <&dmamux1 30 0x400 0x1>,
-			       <&dmamux1 31 0x400 0x1>,
-			       <&dmamux1 32 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
+		pwr_mcu: pwr_mcu@50001014 {
+			compatible = "st,stm32mp151-pwr-mcu", "syscon";
+			reg = <0x50001014 0x4>;
+		};
 
-			timer@3 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <3>;
-				status = "disabled";
-			};
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp1-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		syscfg: syscon@50020000 {
+			compatible = "st,stm32mp157-syscfg", "syscon";
+			reg = <0x50020000 0x400>;
+			clocks = <&rcc SYSCFG>;
 		};
 
-		timers5: timer@40003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40003000 0x400>;
-			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM5_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 55 0x400 0x1>,
-			       <&dmamux1 56 0x400 0x1>,
-			       <&dmamux1 57 0x400 0x1>,
-			       <&dmamux1 58 0x400 0x1>,
-			       <&dmamux1 59 0x400 0x1>,
-			       <&dmamux1 60 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+		dts: thermal@50028000 {
+			compatible = "st,stm32-thermal";
+			reg = <0x50028000 0x100>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc TMPSENS>;
+			clock-names = "pclk";
+			#thermal-sensor-cells = <0>;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@4 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <4>;
-				status = "disabled";
-			};
-
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
-			};
+		mdma1: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			resets = <&rcc MDMA_R>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
 		};
 
-		timers6: timer@40004000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40004000 0x400>;
-			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM6_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 69 0x400 0x1>;
-			dma-names = "up";
+		sdmmc1: mmc@58005000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58005000 0x1000>;
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC1_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
 			status = "disabled";
-
-			timer@5 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <5>;
-				status = "disabled";
-			};
 		};
 
-		timers7: timer@40005000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40005000 0x400>;
-			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM7_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 70 0x400 0x1>;
-			dma-names = "up";
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00253180>;
+			reg = <0x58007000 0x1000>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <120000000>;
 			status = "disabled";
-
-			timer@6 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <6>;
-				status = "disabled";
-			};
 		};
 
-		timers12: timer@40006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40006000 0x400>;
-			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM12_K>;
-			clock-names = "int";
+		crc1: crc@58009000 {
+			compatible = "st,stm32f7-crc";
+			reg = <0x58009000 0x400>;
+			clocks = <&rcc CRC1>;
 			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@11 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <11>;
-				status = "disabled";
-			};
 		};
 
-		timers13: timer@40007000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40007000 0x400>;
-			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM13_K>;
-			clock-names = "int";
+		usbh_ohci: usb@5800c000 {
+			compatible = "generic-ohci";
+			reg = <0x5800c000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@12 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <12>;
-				status = "disabled";
-			};
 		};
 
-		timers14: timer@40008000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x40008000 0x400>;
-			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM14_K>;
-			clock-names = "int";
+		usbh_ehci: usb@5800d000 {
+			compatible = "generic-ehci";
+			reg = <0x5800d000 0x1000>;
+			clocks = <&usbphyc>, <&rcc USBH>;
+			resets = <&rcc USBH_R>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			companion = <&usbh_ohci>;
 			status = "disabled";
+		};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
+		ltdc: display-controller@5a001000 {
+			compatible = "st,stm32-ltdc";
+			reg = <0x5a001000 0x400>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc LTDC_PX>;
+			clock-names = "lcd";
+			resets = <&rcc LTDC_R>;
+			status = "disabled";
+		};
 
-			timer@13 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <13>;
-				status = "disabled";
-			};
+		iwdg2: watchdog@5a002000 {
+			compatible = "st,stm32mp1-iwdg";
+			reg = <0x5a002000 0x400>;
+			clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
+			clock-names = "pclk", "lsi";
+			status = "disabled";
 		};
 
-		lptimer1: timer@40009000 {
+		usbphyc: usbphyc@5a006000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x40009000 0x400>;
-			interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM1_K>;
-			clock-names = "mux";
-			wakeup-source;
+			#clock-cells = <0>;
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc USBPHY_K>;
+			resets = <&rcc USBPHY_R>;
+			vdda1v1-supply = <&reg11>;
+			vdda1v8-supply = <&reg18>;
 			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			trigger@0 {
-				compatible = "st,stm32-lptimer-trigger";
+			usbphyc_port0: usb-phy@0 {
+				#phy-cells = <0>;
 				reg = <0>;
-				status = "disabled";
 			};
 
-			counter {
-				compatible = "st,stm32-lptimer-counter";
-				status = "disabled";
+			usbphyc_port1: usb-phy@1 {
+				#phy-cells = <1>;
+				reg = <1>;
 			};
 		};
 
-		spi2: spi@4000b000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x4000b000 0x400>;
-			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI2_K>;
-			resets = <&rcc SPI2_R>;
-			dmas = <&dmamux1 39 0x400 0x05>,
-			       <&dmamux1 40 0x400 0x05>;
-			dma-names = "rx", "tx";
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			clocks = <&rcc RTCAPB>, <&rcc RTC>;
+			clock-names = "pclk", "rtc_ck";
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
-		i2s2: audio-controller@4000b000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x4000b000 0x400>;
-			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 39 0x400 0x01>,
-			       <&dmamux1 40 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
+		bsec: efuse@5c005000 {
+			compatible = "st,stm32mp15-bsec";
+			reg = <0x5c005000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			part_number_otp: part-number-otp@4 {
+				reg = <0x4 0x1>;
+			};
+			vrefint: vrefin-cal@52 {
+				reg = <0x52 0x2>;
+			};
+			ts_cal1: calib@5c {
+				reg = <0x5c 0x2>;
+			};
+			ts_cal2: calib@5e {
+				reg = <0x5e 0x2>;
+			};
 		};
 
-		spi3: spi@4000c000 {
+		etzpc: bus@5c007000 {
+			compatible = "st,stm32-etzpc";
+			reg = <0x5c007000 0x400>;
 			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x4000c000 0x400>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI3_K>;
-			resets = <&rcc SPI3_R>;
-			dmas = <&dmamux1 61 0x400 0x05>,
-			       <&dmamux1 62 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			#size-cells = <1>;
+			feature-domain-controller;
+			#feature-domain-cells = <1>;
+			ranges;
 
-		i2s3: audio-controller@4000c000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x4000c000 0x400>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 61 0x400 0x01>,
-			       <&dmamux1 62 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers2: timer@40000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40000000 0x400>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM2_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 18 0x400 0x1>,
+				       <&dmamux1 19 0x400 0x1>,
+				       <&dmamux1 20 0x400 0x1>,
+				       <&dmamux1 21 0x400 0x1>,
+				       <&dmamux1 22 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up";
+				feature-domains = <&etzpc 16>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		spdifrx: audio-controller@4000d000 {
-			compatible = "st,stm32h7-spdifrx";
-			#sound-dai-cells = <0>;
-			reg = <0x4000d000 0x400>;
-			clocks = <&rcc SPDIF_K>;
-			clock-names = "kclk";
-			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 93 0x400 0x01>,
-			       <&dmamux1 94 0x400 0x01>;
-			dma-names = "rx", "rx-ctrl";
-			status = "disabled";
-		};
+				timer@1 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <1>;
+					status = "disabled";
+				};
 
-		usart2: serial@4000e000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4000e000 0x400>;
-			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART2_K>;
-			wakeup-source;
-			dmas = <&dmamux1 43 0x400 0x15>,
-			       <&dmamux1 44 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		usart3: serial@4000f000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4000f000 0x400>;
-			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART3_K>;
-			wakeup-source;
-			dmas = <&dmamux1 45 0x400 0x15>,
-			       <&dmamux1 46 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers3: timer@40001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40001000 0x400>;
+				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM3_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 23 0x400 0x1>,
+				       <&dmamux1 24 0x400 0x1>,
+				       <&dmamux1 25 0x400 0x1>,
+				       <&dmamux1 26 0x400 0x1>,
+				       <&dmamux1 27 0x400 0x1>,
+				       <&dmamux1 28 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+				feature-domains = <&etzpc 17>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		uart4: serial@40010000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40010000 0x400>;
-			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART4_K>;
-			wakeup-source;
-			dmas = <&dmamux1 63 0x400 0x15>,
-			       <&dmamux1 64 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				timer@2 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <2>;
+					status = "disabled";
+				};
 
-		uart5: serial@40011000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40011000 0x400>;
-			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART5_K>;
-			wakeup-source;
-			dmas = <&dmamux1 65 0x400 0x15>,
-			       <&dmamux1 66 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		i2c1: i2c@40012000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40012000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C1_K>;
-			resets = <&rcc I2C1_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x1>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+			timers4: timer@40002000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40002000 0x400>;
+				interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM4_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 29 0x400 0x1>,
+				       <&dmamux1 30 0x400 0x1>,
+				       <&dmamux1 31 0x400 0x1>,
+				       <&dmamux1 32 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4";
+				feature-domains = <&etzpc 18>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		i2c2: i2c@40013000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40013000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C2_K>;
-			resets = <&rcc I2C2_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x2>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+				timer@3 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <3>;
+					status = "disabled";
+				};
 
-		i2c3: i2c@40014000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40014000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C3_K>;
-			resets = <&rcc I2C3_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x4>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-		i2c5: i2c@40015000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x40015000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C5_K>;
-			resets = <&rcc I2C5_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x10>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
+			timers5: timer@40003000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40003000 0x400>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM5_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 55 0x400 0x1>,
+				       <&dmamux1 56 0x400 0x1>,
+				       <&dmamux1 57 0x400 0x1>,
+				       <&dmamux1 58 0x400 0x1>,
+				       <&dmamux1 59 0x400 0x1>,
+				       <&dmamux1 60 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
+				feature-domains = <&etzpc 19>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		cec: cec@40016000 {
-			compatible = "st,stm32-cec";
-			reg = <0x40016000 0x400>;
-			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CEC_K>, <&rcc CEC>;
-			clock-names = "cec", "hdmi-cec";
-			status = "disabled";
-		};
+				timer@4 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <4>;
+					status = "disabled";
+				};
 
-		dac: dac@40017000 {
-			compatible = "st,stm32h7-dac-core";
-			reg = <0x40017000 0x400>;
-			clocks = <&rcc DAC12>;
-			clock-names = "pclk";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
 
-			dac1: dac@1 {
-				compatible = "st,stm32-dac";
-				#io-channel-cells = <1>;
-				reg = <1>;
-				status = "disabled";
+			timers6: timer@40004000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40004000 0x400>;
+				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM6_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 69 0x400 0x1>;
+				dma-names = "up";
+				feature-domains = <&etzpc 20>;
+				status = "disabled";
+
+				timer@5 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <5>;
+					status = "disabled";
+				};
 			};
 
-			dac2: dac@2 {
-				compatible = "st,stm32-dac";
-				#io-channel-cells = <1>;
-				reg = <2>;
-				status = "disabled";
+			timers7: timer@40005000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40005000 0x400>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM7_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 70 0x400 0x1>;
+				dma-names = "up";
+				feature-domains = <&etzpc 21>;
+				status = "disabled";
+
+				timer@6 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <6>;
+					status = "disabled";
+				};
 			};
-		};
 
-		uart7: serial@40018000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40018000 0x400>;
-			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART7_K>;
-			wakeup-source;
-			dmas = <&dmamux1 79 0x400 0x15>,
-			       <&dmamux1 80 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			timers12: timer@40006000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40006000 0x400>;
+				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM12_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 22>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		uart8: serial@40019000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x40019000 0x400>;
-			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc UART8_K>;
-			wakeup-source;
-			dmas = <&dmamux1 81 0x400 0x15>,
-			       <&dmamux1 82 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+				timer@11 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <11>;
+					status = "disabled";
+				};
+			};
 
-		timers1: timer@44000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44000000 0x400>;
-			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "brk", "up", "trg-com", "cc";
-			clocks = <&rcc TIM1_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 11 0x400 0x1>,
-			       <&dmamux1 12 0x400 0x1>,
-			       <&dmamux1 13 0x400 0x1>,
-			       <&dmamux1 14 0x400 0x1>,
-			       <&dmamux1 15 0x400 0x1>,
-			       <&dmamux1 16 0x400 0x1>,
-			       <&dmamux1 17 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4",
-				    "up", "trig", "com";
-			status = "disabled";
+			timers13: timer@40007000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40007000 0x400>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM13_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 23>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+				timer@12 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <12>;
+					status = "disabled";
+				};
 			};
 
-			timer@0 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <0>;
-				status = "disabled";
-			};
+			timers14: timer@40008000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x40008000 0x400>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM14_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 24>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
-				status = "disabled";
+				timer@13 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <13>;
+					status = "disabled";
+				};
 			};
-		};
 
-		timers8: timer@44001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44001000 0x400>;
-			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "brk", "up", "trg-com", "cc";
-			clocks = <&rcc TIM8_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 47 0x400 0x1>,
-			       <&dmamux1 48 0x400 0x1>,
-			       <&dmamux1 49 0x400 0x1>,
-			       <&dmamux1 50 0x400 0x1>,
-			       <&dmamux1 51 0x400 0x1>,
-			       <&dmamux1 52 0x400 0x1>,
-			       <&dmamux1 53 0x400 0x1>;
-			dma-names = "ch1", "ch2", "ch3", "ch4",
-				    "up", "trig", "com";
-			status = "disabled";
+			lptimer1: timer@40009000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x40009000 0x400>;
+				interrupts-extended = <&exti 47 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM1_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 25>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
+				trigger@0 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <0>;
+					status = "disabled";
+				};
+
+				counter {
+					compatible = "st,stm32-lptimer-counter";
+					status = "disabled";
+				};
 			};
 
-			timer@7 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <7>;
+			i2s2: audio-controller@4000b000 {
+				compatible = "st,stm32h7-i2s";
+				#sound-dai-cells = <0>;
+				reg = <0x4000b000 0x400>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 39 0x400 0x01>,
+				       <&dmamux1 40 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 27>;
 				status = "disabled";
 			};
 
-			counter {
-				compatible = "st,stm32-timer-counter";
+			spi2: spi@4000b000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x4000b000 0x400>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI2_K>;
+				resets = <&rcc SPI2_R>;
+				dmas = <&dmamux1 39 0x400 0x05>,
+				       <&dmamux1 40 0x400 0x05>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 27>;
 				status = "disabled";
 			};
-		};
-
-		usart6: serial@44003000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x44003000 0x400>;
-			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART6_K>;
-			wakeup-source;
-			dmas = <&dmamux1 71 0x400 0x15>,
-			       <&dmamux1 72 0x400 0x11>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		spi1: spi@44004000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44004000 0x400>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI1_K>;
-			resets = <&rcc SPI1_R>;
-			dmas = <&dmamux1 37 0x400 0x05>,
-			       <&dmamux1 38 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2s1: audio-controller@44004000 {
-			compatible = "st,stm32h7-i2s";
-			#sound-dai-cells = <0>;
-			reg = <0x44004000 0x400>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 37 0x400 0x01>,
-			       <&dmamux1 38 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
 
-		spi4: spi@44005000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44005000 0x400>;
-			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI4_K>;
-			resets = <&rcc SPI4_R>;
-			dmas = <&dmamux1 83 0x400 0x05>,
-			       <&dmamux1 84 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		timers15: timer@44006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44006000 0x400>;
-			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM15_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 105 0x400 0x1>,
-			       <&dmamux1 106 0x400 0x1>,
-			       <&dmamux1 107 0x400 0x1>,
-			       <&dmamux1 108 0x400 0x1>;
-			dma-names = "ch1", "up", "trig", "com";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			i2s3: audio-controller@4000c000 {
+				compatible = "st,stm32h7-i2s";
+				#sound-dai-cells = <0>;
+				reg = <0x4000c000 0x400>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 61 0x400 0x01>,
+				       <&dmamux1 62 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 28>;
 				status = "disabled";
 			};
 
-			timer@14 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <14>;
+			spi3: spi@4000c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x4000c000 0x400>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI3_K>;
+				resets = <&rcc SPI3_R>;
+				dmas = <&dmamux1 61 0x400 0x05>,
+				       <&dmamux1 62 0x400 0x05>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 28>;
 				status = "disabled";
 			};
-		};
-
-		timers16: timer@44007000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44007000 0x400>;
-			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM16_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 109 0x400 0x1>,
-			       <&dmamux1 110 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			spdifrx: audio-controller@4000d000 {
+				compatible = "st,stm32h7-spdifrx";
+				#sound-dai-cells = <0>;
+				reg = <0x4000d000 0x400>;
+				clocks = <&rcc SPDIF_K>;
+				clock-names = "kclk";
+				interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 93 0x400 0x01>,
+				       <&dmamux1 94 0x400 0x01>;
+				dma-names = "rx", "rx-ctrl";
+				feature-domains = <&etzpc 29>;
+				status = "disabled";
+			};
+
+			usart2: serial@4000e000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4000e000 0x400>;
+				interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART2_K>;
+				wakeup-source;
+				dmas = <&dmamux1 43 0x400 0x15>,
+				       <&dmamux1 44 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 30>;
+				status = "disabled";
+			};
+
+			usart3: serial@4000f000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4000f000 0x400>;
+				interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART3_K>;
+				wakeup-source;
+				dmas = <&dmamux1 45 0x400 0x15>,
+				       <&dmamux1 46 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 31>;
+				status = "disabled";
+			};
+
+			uart4: serial@40010000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40010000 0x400>;
+				interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART4_K>;
+				wakeup-source;
+				dmas = <&dmamux1 63 0x400 0x15>,
+				       <&dmamux1 64 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 32>;
+				status = "disabled";
+			};
+
+			uart5: serial@40011000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40011000 0x400>;
+				interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART5_K>;
+				wakeup-source;
+				dmas = <&dmamux1 65 0x400 0x15>,
+				       <&dmamux1 66 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 33>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@40012000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40012000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C1_K>;
+				resets = <&rcc I2C1_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x1>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 34>;
 				status = "disabled";
 			};
-			timer@15 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <15>;
+
+			i2c2: i2c@40013000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40013000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C2_K>;
+				resets = <&rcc I2C2_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x2>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 35>;
 				status = "disabled";
 			};
-		};
 
-		timers17: timer@44008000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x44008000 0x400>;
-			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM17_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 111 0x400 0x1>,
-			       <&dmamux1 112 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
+			i2c3: i2c@40014000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40014000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C3_K>;
+				resets = <&rcc I2C3_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x4>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 36>;
+				status = "disabled";
+			};
 
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
+			i2c5: i2c@40015000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x40015000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C5_K>;
+				resets = <&rcc I2C5_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x10>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 37>;
 				status = "disabled";
 			};
 
-			timer@16 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <16>;
+			cec: cec@40016000 {
+				compatible = "st,stm32-cec";
+				reg = <0x40016000 0x400>;
+				interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc CEC_K>, <&rcc CEC>;
+				clock-names = "cec", "hdmi-cec";
+				feature-domains = <&etzpc 38>;
 				status = "disabled";
 			};
-		};
 
-		spi5: spi@44009000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x44009000 0x400>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI5_K>;
-			resets = <&rcc SPI5_R>;
-			dmas = <&dmamux1 85 0x400 0x05>,
-			       <&dmamux1 86 0x400 0x05>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
+			dac: dac@40017000 {
+				compatible = "st,stm32h7-dac-core";
+				reg = <0x40017000 0x400>;
+				clocks = <&rcc DAC12>;
+				clock-names = "pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				feature-domains = <&etzpc 39>;
+				status = "disabled";
 
-		sai1: sai@4400a000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400a000 0x400>;
-			reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
-			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI1_R>;
-			status = "disabled";
+				dac1: dac@1 {
+					compatible = "st,stm32-dac";
+					#io-channel-cells = <1>;
+					reg = <1>;
+					status = "disabled";
+				};
 
-			sai1a: audio-controller@4400a004 {
-				#sound-dai-cells = <0>;
+				dac2: dac@2 {
+					compatible = "st,stm32-dac";
+					#io-channel-cells = <1>;
+					reg = <2>;
+					status = "disabled";
+				};
+			};
 
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x20>;
-				clocks = <&rcc SAI1_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 87 0x400 0x01>;
+			uart7: serial@40018000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40018000 0x400>;
+				interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART7_K>;
+				wakeup-source;
+				dmas = <&dmamux1 79 0x400 0x15>,
+				       <&dmamux1 80 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 40>;
 				status = "disabled";
 			};
 
-			sai1b: audio-controller@4400a024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI1_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 88 0x400 0x01>;
+			uart8: serial@40019000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x40019000 0x400>;
+				interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc UART8_K>;
+				wakeup-source;
+				dmas = <&dmamux1 81 0x400 0x15>,
+				       <&dmamux1 82 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 41>;
 				status = "disabled";
 			};
-		};
 
-		sai2: sai@4400b000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400b000 0x400>;
-			reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
-			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI2_R>;
-			status = "disabled";
+			timers1: timer@44000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44000000 0x400>;
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "brk", "up", "trg-com", "cc";
+				clocks = <&rcc TIM1_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 11 0x400 0x1>,
+				       <&dmamux1 12 0x400 0x1>,
+				       <&dmamux1 13 0x400 0x1>,
+				       <&dmamux1 14 0x400 0x1>,
+				       <&dmamux1 15 0x400 0x1>,
+				       <&dmamux1 16 0x400 0x1>,
+				       <&dmamux1 17 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4",
+					    "up", "trig", "com";
+				feature-domains = <&etzpc 48>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			sai2a: audio-controller@4400b004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x4 0x20>;
-				clocks = <&rcc SAI2_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 89 0x400 0x01>;
-				status = "disabled";
-			};
+				timer@0 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <0>;
+					status = "disabled";
+				};
 
-			sai2b: audio-controller@4400b024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI2_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 90 0x400 0x01>;
-				status = "disabled";
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
 			};
-		};
 
-		sai3: sai@4400c000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x4400c000 0x400>;
-			reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
-			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI3_R>;
-			status = "disabled";
+			timers8: timer@44001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44001000 0x400>;
+				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "brk", "up", "trg-com", "cc";
+				clocks = <&rcc TIM8_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 47 0x400 0x1>,
+				       <&dmamux1 48 0x400 0x1>,
+				       <&dmamux1 49 0x400 0x1>,
+				       <&dmamux1 50 0x400 0x1>,
+				       <&dmamux1 51 0x400 0x1>,
+				       <&dmamux1 52 0x400 0x1>,
+				       <&dmamux1 53 0x400 0x1>;
+				dma-names = "ch1", "ch2", "ch3", "ch4",
+					    "up", "trig", "com";
+				feature-domains = <&etzpc 49>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			sai3a: audio-controller@4400c004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x20>;
-				clocks = <&rcc SAI3_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 113 0x400 0x01>;
+				timer@7 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <7>;
+					status = "disabled";
+				};
+
+				counter {
+					compatible = "st,stm32-timer-counter";
+					status = "disabled";
+				};
+			};
+
+			usart6: serial@44003000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x44003000 0x400>;
+				interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART6_K>;
+				wakeup-source;
+				dmas = <&dmamux1 71 0x400 0x15>,
+				<&dmamux1 72 0x400 0x11>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 51>;
 				status = "disabled";
 			};
 
-			sai3b: audio-controller@4400c024 {
+			i2s1: audio-controller@44004000 {
+				compatible = "st,stm32h7-i2s";
 				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI3_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 114 0x400 0x01>;
+				reg = <0x44004000 0x400>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 37 0x400 0x01>,
+				<&dmamux1 38 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 52>;
 				status = "disabled";
 			};
-		};
-
-		dfsdm: dfsdm@4400d000 {
-			compatible = "st,stm32mp1-dfsdm";
-			reg = <0x4400d000 0x800>;
-			clocks = <&rcc DFSDM_K>;
-			clock-names = "dfsdm";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
 
-			dfsdm0: filter@0 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <0>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 101 0x400 0x01>;
-				dma-names = "rx";
+			spi1: spi@44004000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44004000 0x400>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI1_K>;
+				resets = <&rcc SPI1_R>;
+				dmas = <&dmamux1 37 0x400 0x05>,
+				<&dmamux1 38 0x400 0x05>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 52>;
 				status = "disabled";
 			};
 
-			dfsdm1: filter@1 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <1>;
-				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 102 0x400 0x01>;
-				dma-names = "rx";
+			spi4: spi@44005000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44005000 0x400>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI4_K>;
+				resets = <&rcc SPI4_R>;
+				dmas = <&dmamux1 83 0x400 0x05>,
+				<&dmamux1 84 0x400 0x05>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 53>;
 				status = "disabled";
 			};
 
-			dfsdm2: filter@2 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <2>;
-				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 103 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers15: timer@44006000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44006000 0x400>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM15_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 105 0x400 0x1>,
+				       <&dmamux1 106 0x400 0x1>,
+				       <&dmamux1 107 0x400 0x1>,
+				       <&dmamux1 108 0x400 0x1>;
+				dma-names = "ch1", "up", "trig", "com";
+				feature-domains = <&etzpc 54>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@14 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <14>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm3: filter@3 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <3>;
-				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 104 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers16: timer@44007000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44007000 0x400>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM16_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 109 0x400 0x1>,
+				<&dmamux1 110 0x400 0x1>;
+				dma-names = "ch1", "up";
+				feature-domains = <&etzpc 55>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+				timer@15 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <15>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm4: filter@4 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <4>;
-				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 91 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+			timers17: timer@44008000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x44008000 0x400>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM17_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 111 0x400 0x1>,
+				<&dmamux1 112 0x400 0x1>;
+				dma-names = "ch1", "up";
+				feature-domains = <&etzpc 56>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@16 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <16>;
+					status = "disabled";
+				};
 			};
 
-			dfsdm5: filter@5 {
-				compatible = "st,stm32-dfsdm-adc";
-				#io-channel-cells = <1>;
-				reg = <5>;
-				interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&dmamux1 92 0x400 0x01>;
-				dma-names = "rx";
+			spi5: spi@44009000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x44009000 0x400>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI5_K>;
+				resets = <&rcc SPI5_R>;
+				dmas = <&dmamux1 85 0x400 0x05>,
+				<&dmamux1 86 0x400 0x05>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 57>;
 				status = "disabled";
 			};
-		};
 
-		dma1: dma-controller@48000000 {
-			compatible = "st,stm32-dma";
-			reg = <0x48000000 0x400>;
-			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc DMA1>;
-			resets = <&rcc DMA1_R>;
-			#dma-cells = <4>;
-			st,mem2mem;
-			dma-requests = <8>;
-		};
+			sai1: sai@4400a000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x4400a000 0x400>;
+				reg = <0x4400a000 0x4>, <0x4400a3f0 0x10>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI1_R>;
+				feature-domains = <&etzpc 58>;
+				status = "disabled";
+
+				sai1a: audio-controller@4400a004 {
+					#sound-dai-cells = <0>;
+
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x4 0x20>;
+					clocks = <&rcc SAI1_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 87 0x400 0x01>;
+					status = "disabled";
+				};
 
-		dma2: dma-controller@48001000 {
-			compatible = "st,stm32-dma";
-			reg = <0x48001000 0x400>;
-			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc DMA2>;
-			resets = <&rcc DMA2_R>;
-			#dma-cells = <4>;
-			st,mem2mem;
-			dma-requests = <8>;
-		};
+				sai1b: audio-controller@4400a024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI1_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 88 0x400 0x01>;
+					status = "disabled";
+				};
+			};
 
-		dmamux1: dma-router@48002000 {
-			compatible = "st,stm32h7-dmamux";
-			reg = <0x48002000 0x40>;
-			#dma-cells = <3>;
-			dma-requests = <128>;
-			dma-masters = <&dma1 &dma2>;
-			dma-channels = <16>;
-			clocks = <&rcc DMAMUX>;
-			resets = <&rcc DMAMUX_R>;
-		};
+			sai2: sai@4400b000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x4400b000 0x400>;
+				reg = <0x4400b000 0x4>, <0x4400b3f0 0x10>;
+				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI2_R>;
+				feature-domains = <&etzpc 59>;
+				status = "disabled";
+
+				sai2a: audio-controller@4400b004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x4 0x20>;
+					clocks = <&rcc SAI2_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 89 0x400 0x01>;
+					status = "disabled";
+				};
 
-		adc: adc@48003000 {
-			compatible = "st,stm32mp1-adc-core";
-			reg = <0x48003000 0x400>;
-			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc ADC12>, <&rcc ADC12_K>;
-			clock-names = "bus", "adc";
-			interrupt-controller;
-			st,syscfg = <&syscfg>;
-			#interrupt-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
+				sai2b: audio-controller@4400b024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI2_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 90 0x400 0x01>;
+					status = "disabled";
+				};
+			};
 
-			adc1: adc@0 {
-				compatible = "st,stm32mp1-adc";
-				#io-channel-cells = <1>;
+			sai3: sai@4400c000 {
+				compatible = "st,stm32h7-sai";
 				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x0>;
-				interrupt-parent = <&adc>;
-				interrupts = <0>;
-				dmas = <&dmamux1 9 0x400 0x01>;
-				dma-names = "rx";
-				status = "disabled";
+				#size-cells = <1>;
+				ranges = <0 0x4400c000 0x400>;
+				reg = <0x4400c000 0x4>, <0x4400c3f0 0x10>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI3_R>;
+				feature-domains = <&etzpc 60>;
+				status = "disabled";
+
+				sai3a: audio-controller@4400c004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x04 0x20>;
+					clocks = <&rcc SAI3_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 113 0x400 0x01>;
+					status = "disabled";
+				};
+
+				sai3b: audio-controller@4400c024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI3_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 114 0x400 0x01>;
+					status = "disabled";
+				};
 			};
 
-			adc2: adc@100 {
-				compatible = "st,stm32mp1-adc";
-				#io-channel-cells = <1>;
+			dfsdm: dfsdm@4400d000 {
+				compatible = "st,stm32mp1-dfsdm";
+				reg = <0x4400d000 0x800>;
+				clocks = <&rcc DFSDM_K>;
+				clock-names = "dfsdm";
 				#address-cells = <1>;
 				#size-cells = <0>;
-				reg = <0x100>;
-				interrupt-parent = <&adc>;
-				interrupts = <1>;
-				dmas = <&dmamux1 10 0x400 0x01>;
-				dma-names = "rx";
-				nvmem-cells = <&vrefint>;
-				nvmem-cell-names = "vrefint";
-				status = "disabled";
-				channel@13 {
-					reg = <13>;
-					label = "vrefint";
+				feature-domains = <&etzpc 61>;
+				status = "disabled";
+
+				dfsdm0: filter@0 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <0>;
+					interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 101 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
 				};
-				channel@14 {
-					reg = <14>;
-					label = "vddcore";
+
+				dfsdm1: filter@1 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <1>;
+					interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 102 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
 				};
-			};
-		};
 
-		sdmmc3: mmc@48004000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x48004000 0x400>;
-			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC3_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC3_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
+				dfsdm2: filter@2 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <2>;
+					interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 103 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-		usbotg_hs: usb-otg@49000000 {
-			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
-			reg = <0x49000000 0x10000>;
-			clocks = <&rcc USBO_K>, <&usbphyc>;
-			clock-names = "otg", "utmi";
-			resets = <&rcc USBO_R>;
-			reset-names = "dwc2";
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			g-rx-fifo-size = <512>;
-			g-np-tx-fifo-size = <32>;
-			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
-			dr_mode = "otg";
-			otg-rev = <0x200>;
-			usb33d-supply = <&usb33>;
-			status = "disabled";
-		};
-
-		ipcc: mailbox@4c001000 {
-			compatible = "st,stm32mp1-ipcc";
-			#mbox-cells = <1>;
-			reg = <0x4c001000 0x400>;
-			st,proc-id = <0>;
-			interrupts-extended =
-				<&exti 61 1>,
-				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "rx", "tx";
-			clocks = <&rcc IPCC>;
-			wakeup-source;
-			status = "disabled";
-		};
-
-		dcmi: dcmi@4c006000 {
-			compatible = "st,stm32-dcmi";
-			reg = <0x4c006000 0x400>;
-			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc CAMITF_R>;
-			clocks = <&rcc DCMI>;
-			clock-names = "mclk";
-			dmas = <&dmamux1 75 0x400 0x01>;
-			dma-names = "tx";
-			status = "disabled";
-		};
-
-		rcc: rcc@50000000 {
-			compatible = "st,stm32mp1-rcc", "syscon";
-			reg = <0x50000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
+				dfsdm3: filter@3 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <3>;
+					interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 104 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-		pwr_regulators: pwr@50001000 {
-			compatible = "st,stm32mp1,pwr-reg";
-			reg = <0x50001000 0x10>;
+				dfsdm4: filter@4 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <4>;
+					interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 91 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-			reg11: reg11 {
-				regulator-name = "reg11";
-				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt = <1100000>;
+				dfsdm5: filter@5 {
+					compatible = "st,stm32-dfsdm-adc";
+					#io-channel-cells = <1>;
+					reg = <5>;
+					interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&dmamux1 92 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 			};
 
-			reg18: reg18 {
-				regulator-name = "reg18";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
+			dma1: dma-controller@48000000 {
+				compatible = "st,stm32-dma";
+				reg = <0x48000000 0x400>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc DMA1>;
+				resets = <&rcc DMA1_R>;
+				#dma-cells = <4>;
+				st,mem2mem;
+				dma-requests = <8>;
+				feature-domains = <&etzpc 88>;
+			};
+
+			dma2: dma-controller@48001000 {
+				compatible = "st,stm32-dma";
+				reg = <0x48001000 0x400>;
+				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc DMA2>;
+				resets = <&rcc DMA2_R>;
+				#dma-cells = <4>;
+				st,mem2mem;
+				dma-requests = <8>;
+				feature-domains = <&etzpc 89>;
+			};
+
+			dmamux1: dma-router@48002000 {
+				compatible = "st,stm32h7-dmamux";
+				reg = <0x48002000 0x40>;
+				#dma-cells = <3>;
+				dma-requests = <128>;
+				dma-masters = <&dma1 &dma2>;
+				dma-channels = <16>;
+				clocks = <&rcc DMAMUX>;
+				resets = <&rcc DMAMUX_R>;
+				feature-domains = <&etzpc 90>;
+			};
+
+			adc: adc@48003000 {
+				compatible = "st,stm32mp1-adc-core";
+				reg = <0x48003000 0x400>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc ADC12>, <&rcc ADC12_K>;
+				clock-names = "bus", "adc";
+				interrupt-controller;
+				st,syscfg = <&syscfg>;
+				#interrupt-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				feature-domains = <&etzpc 72>;
+				status = "disabled";
+
+				adc1: adc@0 {
+					compatible = "st,stm32mp1-adc";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+					interrupt-parent = <&adc>;
+					interrupts = <0>;
+					dmas = <&dmamux1 9 0x400 0x01>;
+					dma-names = "rx";
+					status = "disabled";
+				};
 
-			usb33: usb33 {
-				regulator-name = "usb33";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
+				adc2: adc@100 {
+					compatible = "st,stm32mp1-adc";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x100>;
+					interrupt-parent = <&adc>;
+					interrupts = <1>;
+					dmas = <&dmamux1 10 0x400 0x01>;
+					dma-names = "rx";
+					nvmem-cells = <&vrefint>;
+					nvmem-cell-names = "vrefint";
+					status = "disabled";
+					channel@13 {
+						reg = <13>;
+						label = "vrefint";
+					};
+					channel@14 {
+						reg = <14>;
+						label = "vddcore";
+					};
+				};
 			};
-		};
 
-		pwr_mcu: pwr_mcu@50001014 {
-			compatible = "st,stm32mp151-pwr-mcu", "syscon";
-			reg = <0x50001014 0x4>;
-		};
+			sdmmc3: mmc@48004000 {
+				compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00253180>;
+				reg = <0x48004000 0x400>;
+				interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SDMMC3_K>;
+				clock-names = "apb_pclk";
+				resets = <&rcc SDMMC3_R>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <120000000>;
+				feature-domains = <&etzpc 86>;
+				status = "disabled";
+			};
+
+			usbotg_hs: usb-otg@49000000 {
+				compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+				reg = <0x49000000 0x10000>;
+				clocks = <&rcc USBO_K>, <&usbphyc>;
+				clock-names = "otg", "utmi";
+				resets = <&rcc USBO_R>;
+				reset-names = "dwc2";
+				interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+				g-rx-fifo-size = <512>;
+				g-np-tx-fifo-size = <32>;
+				g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+				dr_mode = "otg";
+				otg-rev = <0x200>;
+				usb33d-supply = <&usb33>;
+				feature-domains = <&etzpc 85>;
+				status = "disabled";
+			};
+
+			dcmi: dcmi@4c006000 {
+				compatible = "st,stm32-dcmi";
+				reg = <0x4c006000 0x400>;
+				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc CAMITF_R>;
+				clocks = <&rcc DCMI>;
+				clock-names = "mclk";
+				dmas = <&dmamux1 75 0x400 0x01>;
+				dma-names = "tx";
+				feature-domains = <&etzpc 70>;
+				status = "disabled";
+			};
+
+			lptimer2: timer@50021000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50021000 0x400>;
+				interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM2_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 64>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-		exti: interrupt-controller@5000d000 {
-			compatible = "st,stm32mp1-exti", "syscon";
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			reg = <0x5000d000 0x400>;
-		};
+				trigger@1 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <1>;
+					status = "disabled";
+				};
 
-		syscfg: syscon@50020000 {
-			compatible = "st,stm32mp157-syscfg", "syscon";
-			reg = <0x50020000 0x400>;
-			clocks = <&rcc SYSCFG>;
-		};
+				counter {
+					compatible = "st,stm32-lptimer-counter";
+					status = "disabled";
+				};
+			};
 
-		lptimer2: timer@50021000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50021000 0x400>;
-			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM2_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
+			lptimer3: timer@50022000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50022000 0x400>;
+				interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM3_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 65>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
+				trigger@2 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <2>;
+					status = "disabled";
+				};
 			};
 
-			trigger@1 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <1>;
+			lptimer4: timer@50023000 {
+				compatible = "st,stm32-lptimer";
+				reg = <0x50023000 0x400>;
+				interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM4_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 66>;
 				status = "disabled";
-			};
 
-			counter {
-				compatible = "st,stm32-lptimer-counter";
-				status = "disabled";
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 			};
-		};
-
-		lptimer3: timer@50022000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50022000 0x400>;
-			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM3_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
+			lptimer5: timer@50024000 {
+				compatible = "st,stm32-lptimer";
+				reg = <0x50024000 0x400>;
+				interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM5_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 67>;
 				status = "disabled";
-			};
 
-			trigger@2 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <2>;
-				status = "disabled";
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
 			};
-		};
-
-		lptimer4: timer@50023000 {
-			compatible = "st,stm32-lptimer";
-			reg = <0x50023000 0x400>;
-			interrupts-extended = <&exti 52 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM4_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
+			vrefbuf: vrefbuf@50025000 {
+				compatible = "st,stm32-vrefbuf";
+				reg = <0x50025000 0x8>;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <2500000>;
+				clocks = <&rcc VREF>;
+				feature-domains = <&etzpc 69>;
 				status = "disabled";
 			};
-		};
 
-		lptimer5: timer@50024000 {
-			compatible = "st,stm32-lptimer";
-			reg = <0x50024000 0x400>;
-			interrupts-extended = <&exti 53 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM5_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
+			sai4: sai@50027000 {
+				compatible = "st,stm32h7-sai";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x50027000 0x400>;
+				reg = <0x50027000 0x4>, <0x500273f0 0x10>;
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+				resets = <&rcc SAI4_R>;
+				feature-domains = <&etzpc 68>;
+				status = "disabled";
+
+				sai4a: audio-controller@50027004 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-a";
+					reg = <0x04 0x20>;
+					clocks = <&rcc SAI4_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 99 0x400 0x01>;
+					status = "disabled";
+				};
 
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
+				sai4b: audio-controller@50027024 {
+					#sound-dai-cells = <0>;
+					compatible = "st,stm32-sai-sub-b";
+					reg = <0x24 0x20>;
+					clocks = <&rcc SAI4_K>;
+					clock-names = "sai_ck";
+					dmas = <&dmamux1 100 0x400 0x01>;
+					status = "disabled";
+				};
 			};
-		};
 
-		vrefbuf: vrefbuf@50025000 {
-			compatible = "st,stm32-vrefbuf";
-			reg = <0x50025000 0x8>;
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <2500000>;
-			clocks = <&rcc VREF>;
-			status = "disabled";
-		};
-
-		sai4: sai@50027000 {
-			compatible = "st,stm32h7-sai";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x50027000 0x400>;
-			reg = <0x50027000 0x4>, <0x500273f0 0x10>;
-			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
-			resets = <&rcc SAI4_R>;
-			status = "disabled";
+			hash1: hash@54002000 {
+				compatible = "st,stm32f756-hash";
+				reg = <0x54002000 0x400>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc HASH1>;
+				resets = <&rcc HASH1_R>;
+				dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
+				dma-names = "in";
+				dma-maxburst = <2>;
+				feature-domains = <&etzpc 8>;
+				status = "disabled";
+			};
+
+			rng1: rng@54003000 {
+				compatible = "st,stm32-rng";
+				reg = <0x54003000 0x400>;
+				clocks = <&rcc RNG1_K>;
+				resets = <&rcc RNG1_R>;
+				feature-domains = <&etzpc 7>;
+				status = "okay";
+			};
+
+			fmc: memory-controller@58002000 {
+				#address-cells = <2>;
+				#size-cells = <1>;
+				compatible = "st,stm32mp1-fmc2-ebi";
+				reg = <0x58002000 0x1000>;
+				clocks = <&rcc FMC_K>;
+				resets = <&rcc FMC_R>;
+				feature-domains = <&etzpc 91>;
+				status = "disabled";
+
+				ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+					 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+					 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+					 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+					 <4 0 0x80000000 0x10000000>; /* NAND */
+
+				nand-controller@4,0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "st,stm32mp1-fmc2-nfc";
+					reg = <4 0x00000000 0x1000>,
+					      <4 0x08010000 0x1000>,
+					      <4 0x08020000 0x1000>,
+					      <4 0x01000000 0x1000>,
+					      <4 0x09010000 0x1000>,
+					      <4 0x09020000 0x1000>;
+					interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+					       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+					       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+					dma-names = "tx", "rx", "ecc";
+					status = "disabled";
+				};
+			};
 
-			sai4a: audio-controller@50027004 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-a";
-				reg = <0x04 0x20>;
-				clocks = <&rcc SAI4_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 99 0x400 0x01>;
-				status = "disabled";
+			qspi: spi@58003000 {
+				compatible = "st,stm32f469-qspi";
+				reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+				reg-names = "qspi", "qspi_mm";
+				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
+				       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
+				dma-names = "tx", "rx";
+				clocks = <&rcc QSPI_K>;
+				resets = <&rcc QSPI_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				feature-domains = <&etzpc 92>;
+				status = "disabled";
+			};
+
+			ethernet0: ethernet@5800a000 {
+				compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
+				reg = <0x5800a000 0x2000>;
+				reg-names = "stmmaceth";
+				interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "macirq";
+				clock-names = "stmmaceth",
+					      "mac-clk-tx",
+					      "mac-clk-rx",
+					      "eth-ck",
+					      "ptp_ref",
+					      "ethstp";
+				clocks = <&rcc ETHMAC>,
+					 <&rcc ETHTX>,
+					 <&rcc ETHRX>,
+					 <&rcc ETHCK_K>,
+					 <&rcc ETHPTP_K>,
+					 <&rcc ETHSTP>;
+				st,syscon = <&syscfg 0x4>;
+				snps,mixed-burst;
+				snps,pbl = <2>;
+				snps,en-tx-lpi-clockgating;
+				snps,axi-config = <&stmmac_axi_config_0>;
+				snps,tso;
+				feature-domains = <&etzpc 94>;
+				status = "disabled";
+
+				stmmac_axi_config_0: stmmac-axi-config {
+					snps,wr_osr_lmt = <0x7>;
+					snps,rd_osr_lmt = <0x7>;
+					snps,blen = <0 0 0 0 16 8 4>;
+				};
 			};
 
-			sai4b: audio-controller@50027024 {
-				#sound-dai-cells = <0>;
-				compatible = "st,stm32-sai-sub-b";
-				reg = <0x24 0x20>;
-				clocks = <&rcc SAI4_K>;
-				clock-names = "sai_ck";
-				dmas = <&dmamux1 100 0x400 0x01>;
+			usart1: serial@5c000000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x5c000000 0x400>;
+				interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART1_K>;
+				wakeup-source;
+				feature-domains = <&etzpc 3>;
 				status = "disabled";
 			};
-		};
-
-		dts: thermal@50028000 {
-			compatible = "st,stm32-thermal";
-			reg = <0x50028000 0x100>;
-			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc TMPSENS>;
-			clock-names = "pclk";
-			#thermal-sensor-cells = <0>;
-			status = "disabled";
-		};
-
-		hash1: hash@54002000 {
-			compatible = "st,stm32f756-hash";
-			reg = <0x54002000 0x400>;
-			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc HASH1>;
-			resets = <&rcc HASH1_R>;
-			dmas = <&mdma1 31 0x2 0x1000A02 0x0 0x0>;
-			dma-names = "in";
-			dma-maxburst = <2>;
-			status = "disabled";
-		};
-
-		rng1: rng@54003000 {
-			compatible = "st,stm32-rng";
-			reg = <0x54003000 0x400>;
-			clocks = <&rcc RNG1_K>;
-			resets = <&rcc RNG1_R>;
-			status = "disabled";
-		};
 
-		mdma1: dma-controller@58000000 {
-			compatible = "st,stm32h7-mdma";
-			reg = <0x58000000 0x1000>;
-			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc MDMA>;
-			resets = <&rcc MDMA_R>;
-			#dma-cells = <5>;
-			dma-channels = <32>;
-			dma-requests = <48>;
-		};
-
-		fmc: memory-controller@58002000 {
-			#address-cells = <2>;
-			#size-cells = <1>;
-			compatible = "st,stm32mp1-fmc2-ebi";
-			reg = <0x58002000 0x1000>;
-			clocks = <&rcc FMC_K>;
-			resets = <&rcc FMC_R>;
-			status = "disabled";
-
-			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
-				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
-				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
-				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
-				 <4 0 0x80000000 0x10000000>; /* NAND */
-
-			nand-controller@4,0 {
+			spi6: spi@5c001000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32h7-spi";
+				reg = <0x5c001000 0x400>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI6_K>;
+				resets = <&rcc SPI6_R>;
+				dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
+				       <&mdma1 35 0x0 0x40002 0x0 0x0>;
+				feature-domains = <&etzpc 4>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
+			i2c4: i2c@5c002000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x5c002000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C4_K>;
+				resets = <&rcc I2C4_R>;
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "st,stm32mp1-fmc2-nfc";
-				reg = <4 0x00000000 0x1000>,
-				      <4 0x08010000 0x1000>,
-				      <4 0x08020000 0x1000>,
-				      <4 0x01000000 0x1000>,
-				      <4 0x09010000 0x1000>,
-				      <4 0x09020000 0x1000>;
-				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
-				       <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
-				       <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
-				dma-names = "tx", "rx", "ecc";
+				st,syscfg-fmp = <&syscfg 0x4 0x8>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 5>;
 				status = "disabled";
 			};
-		};
-
-		qspi: spi@58003000 {
-			compatible = "st,stm32f469-qspi";
-			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
-			reg-names = "qspi", "qspi_mm";
-			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&mdma1 22 0x2 0x10100002 0x0 0x0>,
-			       <&mdma1 22 0x2 0x10100008 0x0 0x0>;
-			dma-names = "tx", "rx";
-			clocks = <&rcc QSPI_K>;
-			resets = <&rcc QSPI_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		sdmmc1: mmc@58005000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x58005000 0x1000>;
-			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC1_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC1_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		sdmmc2: mmc@58007000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
-			reg = <0x58007000 0x1000>;
-			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC2_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC2_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <120000000>;
-			status = "disabled";
-		};
-
-		crc1: crc@58009000 {
-			compatible = "st,stm32f7-crc";
-			reg = <0x58009000 0x400>;
-			clocks = <&rcc CRC1>;
-			status = "disabled";
-		};
-
-		ethernet0: ethernet@5800a000 {
-			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
-			reg = <0x5800a000 0x2000>;
-			reg-names = "stmmaceth";
-			interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq";
-			clock-names = "stmmaceth",
-				      "mac-clk-tx",
-				      "mac-clk-rx",
-				      "eth-ck",
-				      "ptp_ref",
-				      "ethstp";
-			clocks = <&rcc ETHMAC>,
-				 <&rcc ETHTX>,
-				 <&rcc ETHRX>,
-				 <&rcc ETHCK_K>,
-				 <&rcc ETHPTP_K>,
-				 <&rcc ETHSTP>;
-			st,syscon = <&syscfg 0x4>;
-			snps,mixed-burst;
-			snps,pbl = <2>;
-			snps,en-tx-lpi-clockgating;
-			snps,axi-config = <&stmmac_axi_config_0>;
-			snps,tso;
-			status = "disabled";
-
-			stmmac_axi_config_0: stmmac-axi-config {
-				snps,wr_osr_lmt = <0x7>;
-				snps,rd_osr_lmt = <0x7>;
-				snps,blen = <0 0 0 0 16 8 4>;
-			};
-		};
-
-		usbh_ohci: usb@5800c000 {
-			compatible = "generic-ohci";
-			reg = <0x5800c000 0x1000>;
-			clocks = <&usbphyc>, <&rcc USBH>;
-			resets = <&rcc USBH_R>;
-			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
 
-		usbh_ehci: usb@5800d000 {
-			compatible = "generic-ehci";
-			reg = <0x5800d000 0x1000>;
-			clocks = <&usbphyc>, <&rcc USBH>;
-			resets = <&rcc USBH_R>;
-			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			companion = <&usbh_ohci>;
-			status = "disabled";
-		};
-
-		ltdc: display-controller@5a001000 {
-			compatible = "st,stm32-ltdc";
-			reg = <0x5a001000 0x400>;
-			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LTDC_PX>;
-			clock-names = "lcd";
-			resets = <&rcc LTDC_R>;
-			status = "disabled";
-		};
-
-		iwdg2: watchdog@5a002000 {
-			compatible = "st,stm32mp1-iwdg";
-			reg = <0x5a002000 0x400>;
-			clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
-			clock-names = "pclk", "lsi";
-			status = "disabled";
-		};
-
-		usbphyc: usbphyc@5a006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			#clock-cells = <0>;
-			compatible = "st,stm32mp1-usbphyc";
-			reg = <0x5a006000 0x1000>;
-			clocks = <&rcc USBPHY_K>;
-			resets = <&rcc USBPHY_R>;
-			vdda1v1-supply = <&reg11>;
-			vdda1v8-supply = <&reg18>;
-			status = "disabled";
-
-			usbphyc_port0: usb-phy@0 {
-				#phy-cells = <0>;
-				reg = <0>;
-			};
-
-			usbphyc_port1: usb-phy@1 {
-				#phy-cells = <1>;
-				reg = <1>;
-			};
-		};
-
-		usart1: serial@5c000000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x5c000000 0x400>;
-			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART1_K>;
-			wakeup-source;
-			status = "disabled";
-		};
-
-		spi6: spi@5c001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32h7-spi";
-			reg = <0x5c001000 0x400>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI6_K>;
-			resets = <&rcc SPI6_R>;
-			dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
-			       <&mdma1 35 0x0 0x40002 0x0 0x0>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2c4: i2c@5c002000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x5c002000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C4_K>;
-			resets = <&rcc I2C4_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x8>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
-		rtc: rtc@5c004000 {
-			compatible = "st,stm32mp1-rtc";
-			reg = <0x5c004000 0x400>;
-			clocks = <&rcc RTCAPB>, <&rcc RTC>;
-			clock-names = "pclk", "rtc_ck";
-			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
-			status = "disabled";
-		};
-
-		bsec: efuse@5c005000 {
-			compatible = "st,stm32mp15-bsec";
-			reg = <0x5c005000 0x400>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			part_number_otp: part-number-otp@4 {
-				reg = <0x4 0x1>;
-			};
-			vrefint: vrefin-cal@52 {
-				reg = <0x52 0x2>;
-			};
-			ts_cal1: calib@5c {
-				reg = <0x5c 0x2>;
-			};
-			ts_cal2: calib@5e {
-				reg = <0x5e 0x2>;
+			i2c6: i2c@5c009000 {
+				compatible = "st,stm32mp15-i2c";
+				reg = <0x5c009000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C6_K>;
+				resets = <&rcc I2C6_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				st,syscfg-fmp = <&syscfg 0x4 0x20>;
+				wakeup-source;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 12>;
+				status = "disabled";
 			};
 		};
 
-		i2c6: i2c@5c009000 {
-			compatible = "st,stm32mp15-i2c";
-			reg = <0x5c009000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C6_K>;
-			resets = <&rcc I2C6_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			st,syscfg-fmp = <&syscfg 0x4 0x20>;
-			wakeup-source;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
 		tamp: tamp@5c00a000 {
 			compatible = "st,stm32-tamp", "syscon", "simple-mfd";
 			reg = <0x5c00a000 0x400>;
diff --git a/arch/arm/boot/dts/st/stm32mp153.dtsi b/arch/arm/boot/dts/st/stm32mp153.dtsi
index 486084e0b80b..82073dd85f18 100644
--- a/arch/arm/boot/dts/st/stm32mp153.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp153.dtsi
@@ -28,32 +28,34 @@ timer {
 			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+};
 
-	soc {
-		m_can1: can@4400e000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
+&etzpc {
+	m_can1: can@4400e000 {
+		compatible = "bosch,m_can";
+		reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
+		reg-names = "m_can", "message_ram";
+		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+		feature-domains = <&etzpc 62>;
+		status = "disabled";
+	};
 
-		m_can2: can@4400f000 {
-			compatible = "bosch,m_can";
-			reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
-			clock-names = "hclk", "cclk";
-			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
-			status = "disabled";
-		};
+	m_can2: can@4400f000 {
+		compatible = "bosch,m_can";
+		reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
+		reg-names = "m_can", "message_ram";
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
+		clock-names = "hclk", "cclk";
+		bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
+		feature-domains = <&etzpc 62>;
+		status = "disabled";
 	};
 };
diff --git a/arch/arm/boot/dts/st/stm32mp15xc.dtsi b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
index b06a55a2fa18..55524a8d3093 100644
--- a/arch/arm/boot/dts/st/stm32mp15xc.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp15xc.dtsi
@@ -4,15 +4,14 @@
  * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
  */
 
-/ {
-	soc {
-		cryp1: cryp@54001000 {
-			compatible = "st,stm32mp1-cryp";
-			reg = <0x54001000 0x400>;
-			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CRYP1>;
-			resets = <&rcc CRYP1_R>;
-			status = "disabled";
-		};
+&etzpc {
+	cryp1: cryp@54001000 {
+		compatible = "st,stm32mp1-cryp";
+		reg = <0x54001000 0x400>;
+		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CRYP1>;
+		resets = <&rcc CRYP1_R>;
+		feature-domains = <&etzpc 9>;
+		status = "disabled";
 	};
 };
-- 
2.25.1

[PATCH v3 11/11] ARM: dts: stm32: add ETZPC as a system bus for STM32MP13x boards

[Gatien Chevallier]

ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and reference ETZPC as a
feature-domain-controller.

For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP13 reference manual.

Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp131.dtsi  | 1027 +++++++++++++------------
 arch/arm/boot/dts/st/stm32mp133.dtsi  |   51 +-
 arch/arm/boot/dts/st/stm32mp13xc.dtsi |   19 +-
 arch/arm/boot/dts/st/stm32mp13xf.dtsi |   19 +-
 4 files changed, 576 insertions(+), 540 deletions(-)

diff --git a/arch/arm/boot/dts/st/stm32mp131.dtsi b/arch/arm/boot/dts/st/stm32mp131.dtsi
index d163c267e34c..0bd9494cafa2 100644
--- a/arch/arm/boot/dts/st/stm32mp131.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp131.dtsi
@@ -757,340 +757,6 @@ dmamux1: dma-router@48002000 {
 			dma-channels = <16>;
 		};
 
-		adc_2: adc@48004000 {
-			compatible = "st,stm32mp13-adc-core";
-			reg = <0x48004000 0x400>;
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc ADC2>, <&rcc ADC2_K>;
-			clock-names = "bus", "adc";
-			interrupt-controller;
-			#interrupt-cells = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-
-			adc2: adc@0 {
-				compatible = "st,stm32mp13-adc";
-				#io-channel-cells = <1>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x0>;
-				interrupt-parent = <&adc_2>;
-				interrupts = <0>;
-				dmas = <&dmamux1 10 0x400 0x80000001>;
-				dma-names = "rx";
-				status = "disabled";
-
-				channel@13 {
-					reg = <13>;
-					label = "vrefint";
-				};
-				channel@14 {
-					reg = <14>;
-					label = "vddcore";
-				};
-				channel@16 {
-					reg = <16>;
-					label = "vddcpu";
-				};
-				channel@17 {
-					reg = <17>;
-					label = "vddq_ddr";
-				};
-			};
-		};
-
-		usbotg_hs: usb@49000000 {
-			compatible = "st,stm32mp15-hsotg", "snps,dwc2";
-			reg = <0x49000000 0x40000>;
-			clocks = <&rcc USBO_K>;
-			clock-names = "otg";
-			resets = <&rcc USBO_R>;
-			reset-names = "dwc2";
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			g-rx-fifo-size = <512>;
-			g-np-tx-fifo-size = <32>;
-			g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
-			dr_mode = "otg";
-			otg-rev = <0x200>;
-			usb33d-supply = <&usb33>;
-			status = "disabled";
-		};
-
-		usart1: serial@4c000000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4c000000 0x400>;
-			interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART1_K>;
-			resets = <&rcc USART1_R>;
-			wakeup-source;
-			dmas = <&dmamux1 41 0x400 0x5>,
-			       <&dmamux1 42 0x400 0x1>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		usart2: serial@4c001000 {
-			compatible = "st,stm32h7-uart";
-			reg = <0x4c001000 0x400>;
-			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc USART2_K>;
-			resets = <&rcc USART2_R>;
-			wakeup-source;
-			dmas = <&dmamux1 43 0x400 0x5>,
-			       <&dmamux1 44 0x400 0x1>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2s4: audio-controller@4c002000 {
-			compatible = "st,stm32h7-i2s";
-			reg = <0x4c002000 0x400>;
-			#sound-dai-cells = <0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dmamux1 83 0x400 0x01>,
-			       <&dmamux1 84 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		spi4: spi@4c002000 {
-			compatible = "st,stm32h7-spi";
-			reg = <0x4c002000 0x400>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI4_K>;
-			resets = <&rcc SPI4_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&dmamux1 83 0x400 0x01>,
-			       <&dmamux1 84 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		spi5: spi@4c003000 {
-			compatible = "st,stm32h7-spi";
-			reg = <0x4c003000 0x400>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SPI5_K>;
-			resets = <&rcc SPI5_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&dmamux1 85 0x400 0x01>,
-			       <&dmamux1 86 0x400 0x01>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		i2c3: i2c@4c004000 {
-			compatible = "st,stm32mp13-i2c";
-			reg = <0x4c004000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C3_K>;
-			resets = <&rcc I2C3_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&dmamux1 73 0x400 0x1>,
-			       <&dmamux1 74 0x400 0x1>;
-			dma-names = "rx", "tx";
-			st,syscfg-fmp = <&syscfg 0x4 0x4>;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
-		i2c4: i2c@4c005000 {
-			compatible = "st,stm32mp13-i2c";
-			reg = <0x4c005000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C4_K>;
-			resets = <&rcc I2C4_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&dmamux1 75 0x400 0x1>,
-			       <&dmamux1 76 0x400 0x1>;
-			dma-names = "rx", "tx";
-			st,syscfg-fmp = <&syscfg 0x4 0x8>;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
-		i2c5: i2c@4c006000 {
-			compatible = "st,stm32mp13-i2c";
-			reg = <0x4c006000 0x400>;
-			interrupt-names = "event", "error";
-			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc I2C5_K>;
-			resets = <&rcc I2C5_R>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&dmamux1 115 0x400 0x1>,
-			       <&dmamux1 116 0x400 0x1>;
-			dma-names = "rx", "tx";
-			st,syscfg-fmp = <&syscfg 0x4 0x10>;
-			i2c-analog-filter;
-			status = "disabled";
-		};
-
-		timers12: timer@4c007000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c007000 0x400>;
-			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM12_K>;
-			clock-names = "int";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@11 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <11>;
-				status = "disabled";
-			};
-		};
-
-		timers13: timer@4c008000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c008000 0x400>;
-			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM13_K>;
-			clock-names = "int";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@12 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <12>;
-				status = "disabled";
-			};
-		};
-
-		timers14: timer@4c009000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c009000 0x400>;
-			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM14_K>;
-			clock-names = "int";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@13 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <13>;
-				status = "disabled";
-			};
-		};
-
-		timers15: timer@4c00a000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c00a000 0x400>;
-			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM15_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 105 0x400 0x1>,
-			       <&dmamux1 106 0x400 0x1>,
-			       <&dmamux1 107 0x400 0x1>,
-			       <&dmamux1 108 0x400 0x1>;
-			dma-names = "ch1", "up", "trig", "com";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@14 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <14>;
-				status = "disabled";
-			};
-		};
-
-		timers16: timer@4c00b000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c00b000 0x400>;
-			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM16_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 109 0x400 0x1>,
-			       <&dmamux1 110 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@15 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <15>;
-				status = "disabled";
-			};
-		};
-
-		timers17: timer@4c00c000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-timers";
-			reg = <0x4c00c000 0x400>;
-			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "global";
-			clocks = <&rcc TIM17_K>;
-			clock-names = "int";
-			dmas = <&dmamux1 111 0x400 0x1>,
-			       <&dmamux1 112 0x400 0x1>;
-			dma-names = "ch1", "up";
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			timer@16 {
-				compatible = "st,stm32h7-timer-trigger";
-				reg = <16>;
-				status = "disabled";
-			};
-		};
-
 		rcc: rcc@50000000 {
 			compatible = "st,stm32mp13-rcc", "syscon";
 			reg = <0x50000000 0x1000>;
@@ -1117,69 +783,6 @@ syscfg: syscon@50020000 {
 			clocks = <&rcc SYSCFG>;
 		};
 
-		lptimer2: timer@50021000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50021000 0x400>;
-			interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM2_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			trigger@1 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <1>;
-				status = "disabled";
-			};
-
-			counter {
-				compatible = "st,stm32-lptimer-counter";
-				status = "disabled";
-			};
-
-			timer {
-				compatible = "st,stm32-lptimer-timer";
-				status = "disabled";
-			};
-		};
-
-		lptimer3: timer@50022000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "st,stm32-lptimer";
-			reg = <0x50022000 0x400>;
-			interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc LPTIM3_K>;
-			clock-names = "mux";
-			wakeup-source;
-			status = "disabled";
-
-			pwm {
-				compatible = "st,stm32-pwm-lp";
-				#pwm-cells = <3>;
-				status = "disabled";
-			};
-
-			trigger@2 {
-				compatible = "st,stm32-lptimer-trigger";
-				reg = <2>;
-				status = "disabled";
-			};
-
-			timer {
-				compatible = "st,stm32-lptimer-timer";
-				status = "disabled";
-			};
-		};
-
 		lptimer4: timer@50023000 {
 			compatible = "st,stm32-lptimer";
 			reg = <0x50023000 0x400>;
@@ -1232,82 +835,6 @@ mdma: dma-controller@58000000 {
 			dma-requests = <48>;
 		};
 
-		fmc: memory-controller@58002000 {
-			compatible = "st,stm32mp1-fmc2-ebi";
-			reg = <0x58002000 0x1000>;
-			ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
-				 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
-				 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
-				 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
-				 <4 0 0x80000000 0x10000000>; /* NAND */
-			#address-cells = <2>;
-			#size-cells = <1>;
-			clocks = <&rcc FMC_K>;
-			resets = <&rcc FMC_R>;
-			status = "disabled";
-
-			nand-controller@4,0 {
-				compatible = "st,stm32mp1-fmc2-nfc";
-				reg = <4 0x00000000 0x1000>,
-				      <4 0x08010000 0x1000>,
-				      <4 0x08020000 0x1000>,
-				      <4 0x01000000 0x1000>,
-				      <4 0x09010000 0x1000>,
-				      <4 0x09020000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-				dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>,
-				       <&mdma 24 0x2 0x12000a08 0x0 0x0>,
-				       <&mdma 25 0x2 0x12000a0a 0x0 0x0>;
-				dma-names = "tx", "rx", "ecc";
-				status = "disabled";
-			};
-		};
-
-		qspi: spi@58003000 {
-			compatible = "st,stm32f469-qspi";
-			reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
-			reg-names = "qspi", "qspi_mm";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>,
-			       <&mdma 26 0x2 0x10100008 0x0 0x0>;
-			dma-names = "tx", "rx";
-			clocks = <&rcc QSPI_K>;
-			resets = <&rcc QSPI_R>;
-			status = "disabled";
-		};
-
-		sdmmc1: mmc@58005000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x20253180>;
-			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
-			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC1_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC1_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <130000000>;
-			status = "disabled";
-		};
-
-		sdmmc2: mmc@58007000 {
-			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x20253180>;
-			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
-			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc SDMMC2_K>;
-			clock-names = "apb_pclk";
-			resets = <&rcc SDMMC2_R>;
-			cap-sd-highspeed;
-			cap-mmc-highspeed;
-			max-frequency = <130000000>;
-			status = "disabled";
-		};
-
 		usbh_ohci: usb@5800c000 {
 			compatible = "generic-ohci";
 			reg = <0x5800c000 0x1000>;
@@ -1335,29 +862,6 @@ iwdg2: watchdog@5a002000 {
 			status = "disabled";
 		};
 
-		usbphyc: usbphyc@5a006000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			#clock-cells = <0>;
-			compatible = "st,stm32mp1-usbphyc";
-			reg = <0x5a006000 0x1000>;
-			clocks = <&rcc USBPHY_K>;
-			resets = <&rcc USBPHY_R>;
-			vdda1v1-supply = <&reg11>;
-			vdda1v8-supply = <&reg18>;
-			status = "disabled";
-
-			usbphyc_port0: usb-phy@0 {
-				#phy-cells = <0>;
-				reg = <0>;
-			};
-
-			usbphyc_port1: usb-phy@1 {
-				#phy-cells = <1>;
-				reg = <1>;
-			};
-		};
-
 		rtc: rtc@5c004000 {
 			compatible = "st,stm32mp1-rtc";
 			reg = <0x5c004000 0x400>;
@@ -1386,6 +890,536 @@ ts_cal2: calib@5e {
 			};
 		};
 
+		etzpc: bus@5c007000 {
+			compatible = "st,stm32-etzpc";
+			reg = <0x5c007000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			feature-domain-controller;
+			#feature-domain-cells = <1>;
+			ranges;
+
+			adc_2: adc@48004000 {
+				compatible = "st,stm32mp13-adc-core";
+				reg = <0x48004000 0x400>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc ADC2>, <&rcc ADC2_K>;
+				clock-names = "bus", "adc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				feature-domains = <&etzpc 33>;
+				status = "disabled";
+
+				adc2: adc@0 {
+					compatible = "st,stm32mp13-adc";
+					#io-channel-cells = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+					interrupt-parent = <&adc_2>;
+					interrupts = <0>;
+					dmas = <&dmamux1 10 0x400 0x80000001>;
+					dma-names = "rx";
+					status = "disabled";
+
+					channel@13 {
+						reg = <13>;
+						label = "vrefint";
+					};
+					channel@14 {
+						reg = <14>;
+						label = "vddcore";
+					};
+					channel@16 {
+						reg = <16>;
+						label = "vddcpu";
+					};
+					channel@17 {
+						reg = <17>;
+						label = "vddq_ddr";
+					};
+				};
+			};
+
+			usbotg_hs: usb@49000000 {
+				compatible = "st,stm32mp15-hsotg", "snps,dwc2";
+				reg = <0x49000000 0x40000>;
+				clocks = <&rcc USBO_K>;
+				clock-names = "otg";
+				resets = <&rcc USBO_R>;
+				reset-names = "dwc2";
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+				g-rx-fifo-size = <512>;
+				g-np-tx-fifo-size = <32>;
+				g-tx-fifo-size = <256 16 16 16 16 16 16 16>;
+				dr_mode = "otg";
+				otg-rev = <0x200>;
+				usb33d-supply = <&usb33>;
+				feature-domains = <&etzpc 34>;
+				status = "disabled";
+			};
+
+			usart1: serial@4c000000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4c000000 0x400>;
+				interrupts-extended = <&exti 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART1_K>;
+				resets = <&rcc USART1_R>;
+				wakeup-source;
+				dmas = <&dmamux1 41 0x400 0x5>,
+				<&dmamux1 42 0x400 0x1>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 16>;
+				status = "disabled";
+			};
+
+			usart2: serial@4c001000 {
+				compatible = "st,stm32h7-uart";
+				reg = <0x4c001000 0x400>;
+				interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc USART2_K>;
+				resets = <&rcc USART2_R>;
+				wakeup-source;
+				dmas = <&dmamux1 43 0x400 0x5>,
+				<&dmamux1 44 0x400 0x1>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 17>;
+				status = "disabled";
+			};
+
+			i2s4: audio-controller@4c002000 {
+				compatible = "st,stm32h7-i2s";
+				reg = <0x4c002000 0x400>;
+				#sound-dai-cells = <0>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dmamux1 83 0x400 0x01>,
+				<&dmamux1 84 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 13>;
+				status = "disabled";
+			};
+
+			spi4: spi@4c002000 {
+				compatible = "st,stm32h7-spi";
+				reg = <0x4c002000 0x400>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI4_K>;
+				resets = <&rcc SPI4_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dmamux1 83 0x400 0x01>,
+				       <&dmamux1 84 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 18>;
+				status = "disabled";
+			};
+
+			spi5: spi@4c003000 {
+				compatible = "st,stm32h7-spi";
+				reg = <0x4c003000 0x400>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SPI5_K>;
+				resets = <&rcc SPI5_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dmamux1 85 0x400 0x01>,
+				       <&dmamux1 86 0x400 0x01>;
+				dma-names = "rx", "tx";
+				feature-domains = <&etzpc 19>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@4c004000 {
+				compatible = "st,stm32mp13-i2c";
+				reg = <0x4c004000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C3_K>;
+				resets = <&rcc I2C3_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dmamux1 73 0x400 0x1>,
+				       <&dmamux1 74 0x400 0x1>;
+				dma-names = "rx", "tx";
+				st,syscfg-fmp = <&syscfg 0x4 0x4>;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 20>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@4c005000 {
+				compatible = "st,stm32mp13-i2c";
+				reg = <0x4c005000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C4_K>;
+				resets = <&rcc I2C4_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dmamux1 75 0x400 0x1>,
+				       <&dmamux1 76 0x400 0x1>;
+				dma-names = "rx", "tx";
+				st,syscfg-fmp = <&syscfg 0x4 0x8>;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 21>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@4c006000 {
+				compatible = "st,stm32mp13-i2c";
+				reg = <0x4c006000 0x400>;
+				interrupt-names = "event", "error";
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc I2C5_K>;
+				resets = <&rcc I2C5_R>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dmamux1 115 0x400 0x1>,
+				       <&dmamux1 116 0x400 0x1>;
+				dma-names = "rx", "tx";
+				st,syscfg-fmp = <&syscfg 0x4 0x10>;
+				i2c-analog-filter;
+				feature-domains = <&etzpc 22>;
+				status = "disabled";
+			};
+
+			timers12: timer@4c007000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c007000 0x400>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM12_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 23>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@11 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <11>;
+					status = "disabled";
+				};
+			};
+
+			timers13: timer@4c008000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c008000 0x400>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM13_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 24>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@12 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <12>;
+					status = "disabled";
+				};
+			};
+
+			timers14: timer@4c009000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c009000 0x400>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM14_K>;
+				clock-names = "int";
+				feature-domains = <&etzpc 25>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@13 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <13>;
+					status = "disabled";
+				};
+			};
+
+			timers15: timer@4c00a000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c00a000 0x400>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM15_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 105 0x400 0x1>,
+				<&dmamux1 106 0x400 0x1>,
+				<&dmamux1 107 0x400 0x1>,
+				<&dmamux1 108 0x400 0x1>;
+				dma-names = "ch1", "up", "trig", "com";
+				feature-domains = <&etzpc 26>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@14 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <14>;
+					status = "disabled";
+				};
+			};
+
+			timers16: timer@4c00b000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c00b000 0x400>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM16_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 109 0x400 0x1>,
+				<&dmamux1 110 0x400 0x1>;
+				dma-names = "ch1", "up";
+				feature-domains = <&etzpc 27>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@15 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <15>;
+					status = "disabled";
+				};
+			};
+
+			timers17: timer@4c00c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-timers";
+				reg = <0x4c00c000 0x400>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "global";
+				clocks = <&rcc TIM17_K>;
+				clock-names = "int";
+				dmas = <&dmamux1 111 0x400 0x1>,
+				       <&dmamux1 112 0x400 0x1>;
+				dma-names = "ch1", "up";
+				feature-domains = <&etzpc 28>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				timer@16 {
+					compatible = "st,stm32h7-timer-trigger";
+					reg = <16>;
+					status = "disabled";
+				};
+			};
+
+			lptimer2: timer@50021000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50021000 0x400>;
+				interrupts-extended = <&exti 48 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM2_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 1>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				trigger@1 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <1>;
+					status = "disabled";
+				};
+
+				counter {
+					compatible = "st,stm32-lptimer-counter";
+					status = "disabled";
+				};
+
+				timer {
+					compatible = "st,stm32-lptimer-timer";
+					status = "disabled";
+				};
+			};
+
+			lptimer3: timer@50022000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "st,stm32-lptimer";
+				reg = <0x50022000 0x400>;
+				interrupts-extended = <&exti 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc LPTIM3_K>;
+				clock-names = "mux";
+				wakeup-source;
+				feature-domains = <&etzpc 2>;
+				status = "disabled";
+
+				pwm {
+					compatible = "st,stm32-pwm-lp";
+					#pwm-cells = <3>;
+					status = "disabled";
+				};
+
+				trigger@2 {
+					compatible = "st,stm32-lptimer-trigger";
+					reg = <2>;
+					status = "disabled";
+				};
+
+				timer {
+					compatible = "st,stm32-lptimer-timer";
+					status = "disabled";
+				};
+			};
+
+			fmc: memory-controller@58002000 {
+				compatible = "st,stm32mp1-fmc2-ebi";
+				reg = <0x58002000 0x1000>;
+				ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+					 <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+					 <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+					 <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+					 <4 0 0x80000000 0x10000000>; /* NAND */
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clocks = <&rcc FMC_K>;
+				resets = <&rcc FMC_R>;
+				feature-domains = <&etzpc 54>;
+				status = "disabled";
+
+				nand-controller@4,0 {
+					compatible = "st,stm32mp1-fmc2-nfc";
+					reg = <4 0x00000000 0x1000>,
+					      <4 0x08010000 0x1000>,
+					      <4 0x08020000 0x1000>,
+					      <4 0x01000000 0x1000>,
+					      <4 0x09010000 0x1000>,
+					      <4 0x09020000 0x1000>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+					dmas = <&mdma 24 0x2 0x12000a02 0x0 0x0>,
+					       <&mdma 24 0x2 0x12000a08 0x0 0x0>,
+					       <&mdma 25 0x2 0x12000a0a 0x0 0x0>;
+					dma-names = "tx", "rx", "ecc";
+					status = "disabled";
+				};
+			};
+
+			qspi: spi@58003000 {
+				compatible = "st,stm32f469-qspi";
+				reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
+				reg-names = "qspi", "qspi_mm";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&mdma 26 0x2 0x10100002 0x0 0x0>,
+				       <&mdma 26 0x2 0x10100008 0x0 0x0>;
+				dma-names = "tx", "rx";
+				clocks = <&rcc QSPI_K>;
+				resets = <&rcc QSPI_R>;
+				feature-domains = <&etzpc 55>;
+				status = "disabled";
+			};
+
+			sdmmc1: mmc@58005000 {
+				compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x20253180>;
+				reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SDMMC1_K>;
+				clock-names = "apb_pclk";
+				resets = <&rcc SDMMC1_R>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <130000000>;
+				feature-domains = <&etzpc 50>;
+				status = "disabled";
+			};
+
+			sdmmc2: mmc@58007000 {
+				compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x20253180>;
+				reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+				interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&rcc SDMMC2_K>;
+				clock-names = "apb_pclk";
+				resets = <&rcc SDMMC2_R>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <130000000>;
+				feature-domains = <&etzpc 51>;
+				status = "disabled";
+			};
+
+			usbphyc: usbphyc@5a006000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#clock-cells = <0>;
+				compatible = "st,stm32mp1-usbphyc";
+				reg = <0x5a006000 0x1000>;
+				clocks = <&rcc USBPHY_K>;
+				resets = <&rcc USBPHY_R>;
+				vdda1v1-supply = <&reg11>;
+				vdda1v8-supply = <&reg18>;
+				feature-domains = <&etzpc 5>;
+				status = "disabled";
+
+				usbphyc_port0: usb-phy@0 {
+					#phy-cells = <0>;
+					reg = <0>;
+				};
+
+				usbphyc_port1: usb-phy@1 {
+					#phy-cells = <1>;
+					reg = <1>;
+				};
+			};
+
+		};
+
 		/*
 		 * Break node order to solve dependency probe issue between
 		 * pinctrl and exti.
@@ -1397,6 +1431,7 @@ pinctrl: pinctrl@50002000 {
 			ranges = <0 0x50002000 0x8400>;
 			interrupt-parent = <&exti>;
 			st,syscfg = <&exti 0x60 0xff>;
+			pins-are-numbered;
 
 			gpioa: gpio@50002000 {
 				gpio-controller;
diff --git a/arch/arm/boot/dts/st/stm32mp133.dtsi b/arch/arm/boot/dts/st/stm32mp133.dtsi
index df451c3c2a26..be6061552683 100644
--- a/arch/arm/boot/dts/st/stm32mp133.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp133.dtsi
@@ -33,35 +33,38 @@ m_can2: can@4400f000 {
 			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
 			status = "disabled";
 		};
+	};
+};
 
-		adc_1: adc@48003000 {
-			compatible = "st,stm32mp13-adc-core";
-			reg = <0x48003000 0x400>;
-			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc ADC1>, <&rcc ADC1_K>;
-			clock-names = "bus", "adc";
-			interrupt-controller;
-			#interrupt-cells = <1>;
+&etzpc {
+	adc_1: adc@48003000 {
+		compatible = "st,stm32mp13-adc-core";
+		reg = <0x48003000 0x400>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc ADC1>, <&rcc ADC1_K>;
+		clock-names = "bus", "adc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		feature-domains = <&etzpc 32>;
+		status = "disabled";
+
+		adc1: adc@0 {
+			compatible = "st,stm32mp13-adc";
+			#io-channel-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			reg = <0x0>;
+			interrupt-parent = <&adc_1>;
+			interrupts = <0>;
+			dmas = <&dmamux1 9 0x400 0x80000001>;
+			dma-names = "rx";
 			status = "disabled";
 
-			adc1: adc@0 {
-				compatible = "st,stm32mp13-adc";
-				#io-channel-cells = <1>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x0>;
-				interrupt-parent = <&adc_1>;
-				interrupts = <0>;
-				dmas = <&dmamux1 9 0x400 0x80000001>;
-				dma-names = "rx";
-				status = "disabled";
-
-				channel@18 {
-					reg = <18>;
-					label = "vrefint";
-				};
+			channel@18 {
+				reg = <18>;
+				label = "vrefint";
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/st/stm32mp13xc.dtsi b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
index 4d00e7592882..a1a7a40c2a3e 100644
--- a/arch/arm/boot/dts/st/stm32mp13xc.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp13xc.dtsi
@@ -4,15 +4,14 @@
  * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
  */
 
-/ {
-	soc {
-		cryp: crypto@54002000 {
-			compatible = "st,stm32mp1-cryp";
-			reg = <0x54002000 0x400>;
-			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CRYP1>;
-			resets = <&rcc CRYP1_R>;
-			status = "disabled";
-		};
+&etzpc {
+	cryp: crypto@54002000 {
+		compatible = "st,stm32mp1-cryp";
+		reg = <0x54002000 0x400>;
+		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CRYP1>;
+		resets = <&rcc CRYP1_R>;
+		feature-domains = <&etzpc 42>;
+		status = "disabled";
 	};
 };
diff --git a/arch/arm/boot/dts/st/stm32mp13xf.dtsi b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
index 4d00e7592882..a1a7a40c2a3e 100644
--- a/arch/arm/boot/dts/st/stm32mp13xf.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp13xf.dtsi
@@ -4,15 +4,14 @@
  * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
  */
 
-/ {
-	soc {
-		cryp: crypto@54002000 {
-			compatible = "st,stm32mp1-cryp";
-			reg = <0x54002000 0x400>;
-			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CRYP1>;
-			resets = <&rcc CRYP1_R>;
-			status = "disabled";
-		};
+&etzpc {
+	cryp: crypto@54002000 {
+		compatible = "st,stm32mp1-cryp";
+		reg = <0x54002000 0x400>;
+		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rcc CRYP1>;
+		resets = <&rcc CRYP1_R>;
+		feature-domains = <&etzpc 42>;
+		status = "disabled";
 	};
 };
-- 
2.25.1

Re: [IGNORE][PATCH v3 01/11] dt-bindings: Document common device controller bindings

[Gatien CHEVALLIER]

Hello Greg,

On 7/26/23 10:48, Greg KH wrote:
> On Wed, Jul 26, 2023 at 10:38:00AM +0200, Gatien Chevallier wrote:
>> From: Oleksii Moisieiev <Oleksii_Moisieiev@epam.com>
>>
>> Introducing of the common device controller bindings for the controller
>> provider and consumer devices. Those bindings are intended to allow
>> divided system on chip into muliple domains, that can be used to
>> configure hardware permissions.
>>
>> Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
>> ---
>>   .../feature-domain-controller.yaml            | 84 +++++++++++++++++++
>>   1 file changed, 84 insertions(+)
>>   create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
> 
> What is the [IGNORE] prefix for?
> 

I put this prefix to specify that the review for this patch should
not be done on this thread.

It is still under review on the thread linked in the cover-letter.

This series aims to provide a use-case for this binding so its scope
can be better defined.

Best regards,
Gatien

Re: [PATCH v3 04/11] dt-bindings: bus: document ETZPC

[Rob Herring]

On Wed, 26 Jul 2023 11:01:22 +0200, Gatien Chevallier wrote:
> Document ETZPC (Extended TrustZone protection controller). ETZPC is a
> firewall controller.
> 
> Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
> ---
> 
> Changes in V2:
> 	- Corrected errors highlighted by Rob's robot
> 	- No longer define the maxItems for the "feature-domains"
> 	  property
> 	- Fix example (node name, status)
> 	- Declare "feature-domain-names" as an optional
> 	  property for child nodes
> 	- Fix description of "feature-domains" property
> 	- Reorder the properties so it matches RIFSC
> 	- Add missing "feature-domain-controller" property
> 
>  .../bindings/bus/st,stm32-etzpc.yaml          | 96 +++++++++++++++++++
>  1 file changed, 96 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/bus/st,stm32-etzpc.example.dtb: serial@4c001000: Unevaluated properties are not allowed ('feature-domains' was unexpected)
	from schema $id: http://devicetree.org/schemas/serial/st,stm32-uart.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230726090129.233316-1-gatien.chevallier@foss.st.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [IGNORE][PATCH v3 01/11] dt-bindings: Document common device controller bindings

[Rob Herring]

On Wed, 26 Jul 2023 10:38:00 +0200, Gatien Chevallier wrote:
> From: Oleksii Moisieiev <Oleksii_Moisieiev@epam.com>
> 
> Introducing of the common device controller bindings for the controller
> provider and consumer devices. Those bindings are intended to allow
> divided system on chip into muliple domains, that can be used to
> configure hardware permissions.
> 
> Signed-off-by: Oleksii Moisieiev <oleksii_moisieiev@epam.com>
> ---
>  .../feature-domain-controller.yaml            | 84 +++++++++++++++++++
>  1 file changed, 84 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml: title: 'Generic Domain Controller bindings' should not be valid under {'pattern': '([Bb]inding| [Ss]chema)'}
	hint: Everything is a binding/schema, no need to say it. Describe what hardware the binding is for.
	from schema $id: http://devicetree.org/meta-schemas/core.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230726083810.232100-2-gatien.chevallier@foss.st.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v3 02/11] dt-bindings: treewide: add feature-domains description

[Jonathan Cameron]

On Wed, 26 Jul 2023 10:38:01 +0200
Gatien Chevallier <gatien.chevallier@foss.st.com> wrote:

> feature-domains is an optional property that allows a peripheral to
> refer to one or more feature domain controller(s).
> 
> Description of this property is added to all peripheral binding files of
> the peripheral under the STM32 firewall controllers. It allows an accurate
> representation of the hardware, where various peripherals are connected
> to this firewall bus. The firewall can then check the peripheral accesses
> before allowing it to probe.
> 
> Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>

Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> #for IIO

> ---
> 
> Changes in V2: 
> 	- Add missing "feature-domains" property declaration
> 	  in bosch,m_can.yaml and st,stm32-cryp.yaml files
> 
>  Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml  | 4 ++++
>  Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml  | 4 ++++
>  Documentation/devicetree/bindings/dma/st,stm32-dma.yaml      | 4 ++++
>  Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml   | 4 ++++
>  Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml      | 4 ++++
>  Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml  | 4 ++++
>  .../devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml      | 4 ++++
>  Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml  | 4 ++++
>  .../devicetree/bindings/media/cec/st,stm32-cec.yaml          | 4 ++++
>  Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml   | 4 ++++
>  .../bindings/memory-controllers/st,stm32-fmc2-ebi.yaml       | 4 ++++
>  Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml  | 4 ++++
>  Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml   | 5 +++++
>  Documentation/devicetree/bindings/mmc/arm,pl18x.yaml         | 4 ++++
>  Documentation/devicetree/bindings/net/can/bosch,m_can.yaml   | 4 ++++
>  Documentation/devicetree/bindings/net/stm32-dwmac.yaml       | 4 ++++
>  Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml | 4 ++++
>  .../devicetree/bindings/regulator/st,stm32-vrefbuf.yaml      | 4 ++++
>  Documentation/devicetree/bindings/rng/st,stm32-rng.yaml      | 4 ++++
>  Documentation/devicetree/bindings/serial/st,stm32-uart.yaml  | 4 ++++
>  Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml    | 4 ++++
>  Documentation/devicetree/bindings/sound/st,stm32-sai.yaml    | 4 ++++
>  .../devicetree/bindings/sound/st,stm32-spdifrx.yaml          | 4 ++++
>  Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml     | 4 ++++
>  Documentation/devicetree/bindings/spi/st,stm32-spi.yaml      | 4 ++++
>  Documentation/devicetree/bindings/usb/dwc2.yaml              | 4 ++++
>  26 files changed, 105 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
> index 0ddeb8a9a7a0..87a578327fc0 100644
> --- a/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
> +++ b/Documentation/devicetree/bindings/crypto/st,stm32-cryp.yaml
> @@ -46,6 +46,10 @@ properties:
>    power-domains:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
> index b767ec72a999..042a1e005ab2 100644
> --- a/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
> +++ b/Documentation/devicetree/bindings/crypto/st,stm32-hash.yaml
> @@ -50,6 +50,10 @@ properties:
>    power-domains:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
> index 329847ef096a..9f60915e6130 100644
> --- a/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
> +++ b/Documentation/devicetree/bindings/dma/st,stm32-dma.yaml
> @@ -82,6 +82,10 @@ properties:
>      description: if defined, it indicates that the controller
>        supports memory-to-memory transfer
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
> index e722fbcd8a5f..15d33d41098f 100644
> --- a/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
> +++ b/Documentation/devicetree/bindings/dma/st,stm32-dmamux.yaml
> @@ -28,6 +28,10 @@ properties:
>    resets:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
> index 94b75d9f66cd..8a1a21faab8c 100644
> --- a/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
> +++ b/Documentation/devicetree/bindings/i2c/st,stm32-i2c.yaml
> @@ -99,6 +99,10 @@ properties:
>  
>    wakeup-source: true
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
> index 995cbf8cefc6..d59ac9282a28 100644
> --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml
> @@ -93,6 +93,10 @@ properties:
>    '#size-cells':
>      const: 0
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  allOf:
>    - if:
>        properties:
> diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
> index 1970503389aa..39ee55aa4dd8 100644
> --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml
> @@ -59,6 +59,10 @@ properties:
>        If not, SPI CLKOUT frequency will not be accurate.
>      maximum: 20000000
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
> index 04045b932bd2..184d0a44d1de 100644
> --- a/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
> +++ b/Documentation/devicetree/bindings/iio/dac/st,stm32-dac.yaml
> @@ -45,6 +45,10 @@ properties:
>    '#size-cells':
>      const: 0
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  additionalProperties: false
>  
>  required:
> diff --git a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
> index 2314a9a14650..41db21373301 100644
> --- a/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
> +++ b/Documentation/devicetree/bindings/media/cec/st,stm32-cec.yaml
> @@ -29,6 +29,10 @@ properties:
>        - const: cec
>        - const: hdmi-cec
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
> index 6b3e413cedb2..81e1cd5e30cc 100644
> --- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
> +++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
> @@ -36,6 +36,10 @@ properties:
>    resets:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>    port:
>      $ref: /schemas/graph.yaml#/$defs/port-base
>      unevaluatedProperties: false
> diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
> index 14f1833d37c9..4ef01ee4a5e5 100644
> --- a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
> +++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
> @@ -45,6 +45,10 @@ properties:
>        Reflects the memory layout with four integer values per bank. Format:
>        <bank-number> 0 <address of the bank> <size>
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  patternProperties:
>    "^.*@[0-4],[a-f0-9]+$":
>      additionalProperties: true
> diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
> index 27329c5dc38e..156aed282fb8 100644
> --- a/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
> +++ b/Documentation/devicetree/bindings/mfd/st,stm32-lptimer.yaml
> @@ -44,6 +44,10 @@ properties:
>  
>    wakeup-source: true
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>    pwm:
>      type: object
>      additionalProperties: false
> diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
> index f84e09a5743b..d19981ef3fce 100644
> --- a/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
> +++ b/Documentation/devicetree/bindings/mfd/st,stm32-timers.yaml
> @@ -67,6 +67,11 @@ properties:
>    "#size-cells":
>      const: 0
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
> +
>    pwm:
>      type: object
>      additionalProperties: false
> diff --git a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
> index 2459a55ed540..5a8b53d5c35f 100644
> --- a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
> +++ b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml
> @@ -79,6 +79,10 @@ properties:
>            - const: rx
>            - const: tx
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>    power-domains: true
>  
>    resets:
> diff --git a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
> index 67879aab623b..144cbcbefa37 100644
> --- a/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
> +++ b/Documentation/devicetree/bindings/net/can/bosch,m_can.yaml
> @@ -118,6 +118,10 @@ properties:
>    phys:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
> index fc8c96b08d7d..133e1edbd561 100644
> --- a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
> +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
> @@ -93,6 +93,10 @@ properties:
>        select RCC clock instead of ETH_REF_CLK.
>      type: boolean
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - clocks
> diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
> index 24a3dbde223b..89fa65f31d20 100644
> --- a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
> +++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
> @@ -55,6 +55,10 @@ properties:
>      description: number of clock cells for ck_usbo_48m consumer
>      const: 0
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  # Required child nodes:
>  
>  patternProperties:
> diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
> index 05f4ad2c7d3a..b73a97f89fe4 100644
> --- a/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
> +++ b/Documentation/devicetree/bindings/regulator/st,stm32-vrefbuf.yaml
> @@ -30,6 +30,10 @@ properties:
>    vdda-supply:
>      description: phandle to the vdda input analog voltage.
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
> index 187b172d0cca..c45e6285653c 100644
> --- a/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
> +++ b/Documentation/devicetree/bindings/rng/st,stm32-rng.yaml
> @@ -30,6 +30,10 @@ properties:
>      type: boolean
>      description: If set enable the clock detection management
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> index 1df8ffe95fc6..b80d5a8ff4e8 100644
> --- a/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> +++ b/Documentation/devicetree/bindings/serial/st,stm32-uart.yaml
> @@ -70,6 +70,10 @@ properties:
>      enum: [1, 2, 4, 8, 12, 14, 16]
>      default: 8
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  allOf:
>    - $ref: rs485.yaml#
>    - $ref: serial.yaml#
> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
> index b9111d375b93..30339447cc24 100644
> --- a/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
> +++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml
> @@ -65,6 +65,10 @@ properties:
>      $ref: audio-graph-port.yaml#
>      unevaluatedProperties: false
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - "#sound-dai-cells"
> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
> index 56d206f97a96..f59770ead3e3 100644
> --- a/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
> +++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.yaml
> @@ -48,6 +48,10 @@ properties:
>    clock-names:
>      maxItems: 3
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
> index bc48151b9adb..480ce8704fda 100644
> --- a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
> +++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.yaml
> @@ -50,6 +50,10 @@ properties:
>    resets:
>      maxItems: 1
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - "#sound-dai-cells"
> diff --git a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
> index 8bba965a9ae6..3331f6cd1b75 100644
> --- a/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
> +++ b/Documentation/devicetree/bindings/spi/st,stm32-qspi.yaml
> @@ -46,6 +46,10 @@ properties:
>        - const: tx
>        - const: rx
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
> index 9ca1a843c820..a0664a0fcabf 100644
> --- a/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
> +++ b/Documentation/devicetree/bindings/spi/st,stm32-spi.yaml
> @@ -59,6 +59,10 @@ properties:
>        - const: rx
>        - const: tx
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  patternProperties:
>    "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$":
>      type: object
> diff --git a/Documentation/devicetree/bindings/usb/dwc2.yaml b/Documentation/devicetree/bindings/usb/dwc2.yaml
> index 0a5c98ea711d..95b615ee3a07 100644
> --- a/Documentation/devicetree/bindings/usb/dwc2.yaml
> +++ b/Documentation/devicetree/bindings/usb/dwc2.yaml
> @@ -172,6 +172,10 @@ properties:
>  
>    tpl-support: true
>  
> +  feature-domains:
> +    minItems: 1
> +    maxItems: 2
> +
>  dependencies:
>    port: [ usb-role-switch ]
>    role-switch-default-mode: [ usb-role-switch ]

Re: [PATCH v3 00/11] Introduce STM32 Firewall framework

[Gatien CHEVALLIER]

Hello all,

Since the "feature-domains" bindings lacks precision (maybe some
renaming for better clarity on its purpose), I will send v4 with a
vendor binding so the generic one better discussed and enriched with
other contributor examples.

This will avoid mixing several patch set.

Best regards,
Gatien

On 7/26/23 10:37, Gatien Chevallier wrote:
> Introduce STM32 Firewall framework for STM32MP1x and STM32MP2x
> platforms. STM32MP1x(ETZPC) and STM32MP2x(RIFSC) Firewall controllers
> register to the framework to offer firewall services such as access
> granting.
> 
> This series of patches is a new approach on the previous STM32 system
> bus, history is available here:
> https://lore.kernel.org/lkml/20230127164040.1047583/
> 
> The need for such framework arises from the fact that there are now
> multiple hardware firewalls implemented across multiple products.
> Drivers are shared between different products, using the same code.
> When it comes to firewalls, the purpose mostly stays the same: Protect
> hardware resources. But the implementation differs, and there are
> multiple types of firewalls: peripheral, memory, ...
> 
> Some hardware firewall controllers such as the RIFSC implemented on
> STM32MP2x platforms may require to take ownership of a resource before
> being able to use it, hence the requirement for firewall services to
> take/release the ownership of such resources.
> 
> On the other hand, hardware firewall configurations are becoming
> more and more complex. These mecanisms prevent platform crashes
> or other firewall-related incoveniences by denying access to some
> resources.
> 
> The stm32 firewall framework offers an API that is defined in
> firewall controllers drivers to best fit the specificity of each
> firewall.
> 
> For every peripherals protected by either the ETZPC or the RIFSC, the
> firewall framework checks the firewall controlelr registers to see if
> the peripheral's access is granted to the Linux kernel. If not, the
> peripheral is configured as secure, the node is marked populated,
> so that the driver is not probed for that device.
> 
> The firewall framework relies on the feature-domain-controller device
> tree bindings: https://lore.kernel.org/lkml/0c0a82bb-18ae-d057-562b.
> It is used by peripherals to reference a domain controller, in this
> case a firewall feature domain. The bus uses the ID referenced by
> the feature-domains property to know where to look in the firewall
> to get the security configuration for the peripheral. This allows
> a device tree description rather than a hardcoded peripheral table
> in the bus driver.
> 
> The STM32 ETZPC device is responsible for filtering accesses based on
> security level, or co-processor isolation for any resource connected
> to it.
> 
> The RIFSC is responsible for filtering accesses based on Compartment
> ID / security level / privilege level for any resource connected to
> it.
> 
> STM32MP13/15/25 SoC device tree files are updated in this series to
> implement this mecanism.
> 
> Changes in V2:
> 
> 	generic:
> 		- Add fw_devlink dependency for "feature-domains"
> 		  property.
> 
> 	bindings:
> 		- Corrected YAMLS errors highlighted by Rob's robot
> 		- Firewall controllers YAMLs no longer define the
> 		  maxItems for the "feature-domains" property
> 		- Renamed st,stm32-rifsc.yaml to
> 		  st,stm32mp25-rifsc.yaml
> 		- Fix examples in YAML files
> 		- Change feature-domains maxItems to 2 in firewall
> 		  consumer files as there should not be more than
> 		  2 entries for now
> 		- Declare "feature-domain-names" as an optional
> 		  property for firewall controllers child nodes.
> 		- Add missing "feature-domains" property declaration
> 		  in bosch,m_can.yaml and st,stm32-cryp.yaml files
> 
> 	firewall framework:
> 		- Support multiple entries for "feature-domains"
> 		  property
> 		- Better handle the device-tree parsing using
> 		  phandle+args APIs
> 		- Remove "resource firewall" type
> 		- Add a field for the name of the firewall entry
> 		- Fix licenses
> 	
> 	RIFSC:
> 		- Add controller name
> 		- Driver is now a module_platform_driver
> 		- Fix license
> 
> 	ETZPC:
> 		- Add controller name
> 		- Driver is now a module_platform_driver
> 		- Fix license
> 
> 	Device trees:
> 		- Fix rifsc node name
> 		- Move the "ranges" property under the
> 		  "feature-domains" one
> 
> Changes in V3:
> 
> 	Change incorrect ordering for bindings commits leading
> 	to an error while running
> 	"make DT_CHECKER_FLAGS=-m dt_binding_check"
> 
> Oleksii Moisieiev (1):
>    dt-bindings: Document common device controller bindings
> 
> Gatien Chevallier (10):
>    dt-bindings: treewide: add feature-domains description
>    dt-bindings: bus: document RIFSC
>    dt-bindings: bus: document ETZPC
>    firewall: introduce stm32_firewall framework
>    of: property: fw_devlink: Add support for "feature-domains"
>    bus: rifsc: introduce RIFSC firewall controller driver
>    arm64: dts: st: add RIFSC as a domain controller for STM32MP25x boards
>    bus: etzpc: introduce ETZPC firewall controller driver
>    ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards
>    ARM: dts: stm32: add ETZPC as a system bus for STM32MP13x boards
> 
>   .../bindings/bus/st,stm32-etzpc.yaml          |   96 +
>   .../bindings/bus/st,stm32mp25-rifsc.yaml      |  105 +
>   .../bindings/crypto/st,stm32-cryp.yaml        |    4 +
>   .../bindings/crypto/st,stm32-hash.yaml        |    4 +
>   .../devicetree/bindings/dma/st,stm32-dma.yaml |    4 +
>   .../bindings/dma/st,stm32-dmamux.yaml         |    4 +
>   .../feature-domain-controller.yaml            |   84 +
>   .../devicetree/bindings/i2c/st,stm32-i2c.yaml |    4 +
>   .../bindings/iio/adc/st,stm32-adc.yaml        |    4 +
>   .../bindings/iio/adc/st,stm32-dfsdm-adc.yaml  |    4 +
>   .../bindings/iio/dac/st,stm32-dac.yaml        |    4 +
>   .../bindings/media/cec/st,stm32-cec.yaml      |    4 +
>   .../bindings/media/st,stm32-dcmi.yaml         |    4 +
>   .../memory-controllers/st,stm32-fmc2-ebi.yaml |    4 +
>   .../bindings/mfd/st,stm32-lptimer.yaml        |    4 +
>   .../bindings/mfd/st,stm32-timers.yaml         |    5 +
>   .../devicetree/bindings/mmc/arm,pl18x.yaml    |    4 +
>   .../bindings/net/can/bosch,m_can.yaml         |    4 +
>   .../devicetree/bindings/net/stm32-dwmac.yaml  |    4 +
>   .../bindings/phy/phy-stm32-usbphyc.yaml       |    4 +
>   .../bindings/regulator/st,stm32-vrefbuf.yaml  |    4 +
>   .../devicetree/bindings/rng/st,stm32-rng.yaml |    4 +
>   .../bindings/serial/st,stm32-uart.yaml        |    4 +
>   .../bindings/sound/st,stm32-i2s.yaml          |    4 +
>   .../bindings/sound/st,stm32-sai.yaml          |    4 +
>   .../bindings/sound/st,stm32-spdifrx.yaml      |    4 +
>   .../bindings/spi/st,stm32-qspi.yaml           |    4 +
>   .../devicetree/bindings/spi/st,stm32-spi.yaml |    4 +
>   .../devicetree/bindings/usb/dwc2.yaml         |    4 +
>   MAINTAINERS                                   |    7 +
>   arch/arm/boot/dts/st/stm32mp131.dtsi          | 1027 +++---
>   arch/arm/boot/dts/st/stm32mp133.dtsi          |   51 +-
>   arch/arm/boot/dts/st/stm32mp13xc.dtsi         |   19 +-
>   arch/arm/boot/dts/st/stm32mp13xf.dtsi         |   19 +-
>   arch/arm/boot/dts/st/stm32mp151.dtsi          | 2757 +++++++++--------
>   arch/arm/boot/dts/st/stm32mp153.dtsi          |   52 +-
>   arch/arm/boot/dts/st/stm32mp15xc.dtsi         |   19 +-
>   arch/arm64/Kconfig.platforms                  |    1 +
>   arch/arm64/boot/dts/st/stm32mp251.dtsi        |    7 +-
>   drivers/bus/Kconfig                           |    9 +
>   drivers/bus/Makefile                          |    1 +
>   drivers/bus/stm32_etzpc.c                     |  141 +
>   drivers/bus/stm32_firewall.c                  |  288 ++
>   drivers/bus/stm32_firewall.h                  |   83 +
>   drivers/bus/stm32_rifsc.c                     |  252 ++
>   drivers/of/property.c                         |    2 +
>   include/linux/bus/stm32_firewall_device.h     |  140 +
>   47 files changed, 3346 insertions(+), 1919 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml
>   create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml
>   create mode 100644 Documentation/devicetree/bindings/feature-controllers/feature-domain-controller.yaml
>   create mode 100644 drivers/bus/stm32_etzpc.c
>   create mode 100644 drivers/bus/stm32_firewall.c
>   create mode 100644 drivers/bus/stm32_firewall.h
>   create mode 100644 drivers/bus/stm32_rifsc.c
>   create mode 100644 include/linux/bus/stm32_firewall_device.h
>