* [PATCH 00/17] ARM: remove old board files
@ 2022-10-19 14:40 Arnd Bergmann
[not found] ` <20221019150410.3851944-1-arnd@kernel.org>
0 siblings, 1 reply; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-19 14:40 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Arnd Bergmann, Russell King, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, Andrew Lunn, Sebastian Hesselbarth,
Gregory Clement, Hartley Sweeten, Alexander Sverdlin,
Paul Walmsley, Kevin Hilman, Vinod Koul, Linus Walleij,
Bartosz Golaszewski, Lee Jones, Ulf Hansson, Mark Brown,
Felipe Balbi, Greg Kroah-Hartman, Alan Stern, Bin Liu,
Helge Deller, Wim Van Sebroeck, Guenter Roeck, Liam Girdwood,
Jaroslav Kysela, Takashi Iwai, Hubert Feurstein,
Krzysztof Halasa, Lennert Buytenhek, Sergey Lapin,
Krzysztof Kozlowski, Dan Williams, Pali Rohár, linux-kernel,
linux-omap, linux-usb, dmaengine, linux-gpio, linux-i2c,
linux-mmc, linux-spi, linux-fbdev, dri-devel, linux-watchdog,
alsa-devel
From: Arnd Bergmann <arnd@arndb.de>
This is the first part of the removal of old board files, addressing
all the easy cases:
cns3xxx and iop32x get removed completely, including a handful of device
driversm while ep93xx, dove, mv78xx0, orion, footbridge and omap1 all
keep basic platform support but drop support for all boards that have
no known users.
There are seven patches for other subsystems in this series. It would
be helpful to get everything merged in the same release if there are no
objections, but I don't care if I include them in the soc tree with an
Ack from the subsystem maintainers or the patches are applied directly
into the subsystem trees.
Arnd Bergmann (17):
ARM: at91: remove stale MAINTAINER file entries
ARM: cns3xxx: remove entire platform
mmc: remove cns3xxx driver
ARM: ep93xx: remove old board files
ASoC: remove unused ep93xx files
ARM: mv78xx0: un-deprecate Terastation WXL
ARM: orion: remove unused board files
ARM: orion5x: remove dsa_chip_data references
ARM: iop32x: remove the platform
dmaengine: remove iop-adma driver
gpio: remove iop driver
ARM: footbridge: remove CATS
ARM: omap1: remove unused board files
ARM: omap1: remove dead code
fbdev: omapfb: remove unused board support
spi: remove omap 100K driver
mfd: remove htc-i2cpld driver
CC: Russell King <linux@armlinux.org.uk>
CC: Aaro Koskinen <aaro.koskinen@iki.fi>
CC: Janusz Krzysztofik <jmkrzyszt@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Gregory Clement <gregory.clement@bootlin.com>
CC: Hartley Sweeten <hsweeten@visionengravers.com>
CC: Alexander Sverdlin <alexander.sverdlin@gmail.com>
CC: Paul Walmsley <paul@pwsan.com>
CC: Kevin Hilman <khilman@kernel.org>
CC: Vinod Koul <vkoul@kernel.org>
CC: Linus Walleij <linus.walleij@linaro.org>
CC: Bartosz Golaszewski <brgl@bgdev.pl>
CC: Lee Jones <lee@kernel.org>
CC: Ulf Hansson <ulf.hansson@linaro.org>
CC: Mark Brown <broonie@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Bin Liu <b-liu@ti.com>
CC: Helge Deller <deller@gmx.de>
CC: Wim Van Sebroeck <wim@linux-watchdog.org>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Jaroslav Kysela <perex@perex.cz>
CC: Takashi Iwai <tiwai@suse.com>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Krzysztof Halasa <khalasa@piap.pl>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Sergey Lapin <slapin@ossfans.org>
CC: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
CC: Dan Williams <dan.j.williams@intel.com>
CC: "Pali Rohár" <pali@kernel.org>
CC: linux-kernel@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-omap@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: dmaengine@vger.kernel.org
CC: linux-gpio@vger.kernel.org
CC: linux-i2c@vger.kernel.org
CC: linux-mmc@vger.kernel.org
CC: linux-spi@vger.kernel.org
CC: linux-fbdev@vger.kernel.org
CC: dri-devel@lists.freedesktop.org
CC: linux-watchdog@vger.kernel.org
CC: alsa-devel@alsa-project.org
MAINTAINERS | 57 -
arch/arm/Kconfig | 6 +-
arch/arm/Kconfig.debug | 52 +-
arch/arm/Makefile | 2 -
arch/arm/boot/compressed/misc-ep93xx.h | 13 +-
arch/arm/configs/cns3420vb_defconfig | 63 -
arch/arm/configs/iop32x_defconfig | 126 --
arch/arm/configs/mv78xx0_defconfig | 3 -
arch/arm/configs/omap1_defconfig | 2 -
arch/arm/kernel/entry-common.S | 15 -
arch/arm/kernel/head.S | 2 +-
arch/arm/mach-cns3xxx/Kconfig | 21 -
arch/arm/mach-cns3xxx/Makefile | 6 -
arch/arm/mach-cns3xxx/cns3420vb.c | 252 ---
arch/arm/mach-cns3xxx/cns3xxx.h | 593 -------
arch/arm/mach-cns3xxx/core.c | 410 -----
arch/arm/mach-cns3xxx/core.h | 32 -
arch/arm/mach-cns3xxx/devices.c | 108 --
arch/arm/mach-cns3xxx/devices.h | 17 -
arch/arm/mach-cns3xxx/pcie.c | 290 ----
arch/arm/mach-cns3xxx/pm.c | 120 --
arch/arm/mach-cns3xxx/pm.h | 20 -
arch/arm/mach-dove/Kconfig | 8 -
arch/arm/mach-dove/Makefile | 1 -
arch/arm/mach-dove/dove-db-setup.c | 101 --
arch/arm/mach-ep93xx/Kconfig | 63 -
arch/arm/mach-ep93xx/Makefile | 5 -
arch/arm/mach-ep93xx/adssphere.c | 41 -
arch/arm/mach-ep93xx/gesbc9312.c | 41 -
arch/arm/mach-ep93xx/micro9.c | 125 --
arch/arm/mach-ep93xx/simone.c | 128 --
arch/arm/mach-ep93xx/snappercl15.c | 162 --
arch/arm/mach-footbridge/Kconfig | 12 -
arch/arm/mach-footbridge/Makefile | 2 -
arch/arm/mach-footbridge/cats-hw.c | 98 --
arch/arm/mach-footbridge/cats-pci.c | 64 -
arch/arm/mach-footbridge/common.c | 3 -
arch/arm/mach-iop32x/Kconfig | 54 -
arch/arm/mach-iop32x/Makefile | 20 -
arch/arm/mach-iop32x/adma.c | 163 --
arch/arm/mach-iop32x/cp6.c | 48 -
arch/arm/mach-iop32x/em7210.c | 232 ---
arch/arm/mach-iop32x/glantank.c | 214 ---
arch/arm/mach-iop32x/glantank.h | 12 -
arch/arm/mach-iop32x/gpio-iop32x.h | 11 -
arch/arm/mach-iop32x/hardware.h | 38 -
arch/arm/mach-iop32x/i2c.c | 92 --
arch/arm/mach-iop32x/iop3xx.h | 326 ----
arch/arm/mach-iop32x/iq31244.c | 333 ----
arch/arm/mach-iop32x/iq31244.h | 16 -
arch/arm/mach-iop32x/iq80321.c | 192 ---
arch/arm/mach-iop32x/iq80321.h | 16 -
arch/arm/mach-iop32x/irq.c | 95 --
arch/arm/mach-iop32x/irqs.h | 48 -
arch/arm/mach-iop32x/n2100.c | 367 -----
arch/arm/mach-iop32x/n2100.h | 18 -
arch/arm/mach-iop32x/pci.c | 404 -----
arch/arm/mach-iop32x/pmu.c | 29 -
arch/arm/mach-iop32x/restart.c | 17 -
arch/arm/mach-iop32x/setup.c | 31 -
arch/arm/mach-iop32x/time.c | 179 --
arch/arm/mach-mv78xx0/Kconfig | 14 +-
arch/arm/mach-mv78xx0/Makefile | 2 -
arch/arm/mach-mv78xx0/db78x00-bp-setup.c | 101 --
arch/arm/mach-mv78xx0/rd78x00-masa-setup.c | 86 -
arch/arm/mach-omap1/Kconfig | 93 +-
arch/arm/mach-omap1/Makefile | 18 -
arch/arm/mach-omap1/board-fsample.c | 366 -----
arch/arm/mach-omap1/board-generic.c | 85 -
arch/arm/mach-omap1/board-h2-mmc.c | 74 -
arch/arm/mach-omap1/board-h2.c | 448 -----
arch/arm/mach-omap1/board-h2.h | 38 -
arch/arm/mach-omap1/board-h3-mmc.c | 64 -
arch/arm/mach-omap1/board-h3.c | 455 -----
arch/arm/mach-omap1/board-h3.h | 35 -
arch/arm/mach-omap1/board-htcherald.c | 585 -------
arch/arm/mach-omap1/board-innovator.c | 481 ------
arch/arm/mach-omap1/board-nand.c | 33 -
arch/arm/mach-omap1/board-palmtt.c | 285 ----
arch/arm/mach-omap1/board-palmz71.c | 300 ----
arch/arm/mach-omap1/board-perseus2.c | 333 ----
arch/arm/mach-omap1/clock_data.c | 17 +-
arch/arm/mach-omap1/common.h | 8 -
arch/arm/mach-omap1/devices.c | 58 +-
arch/arm/mach-omap1/dma.c | 25 +-
arch/arm/mach-omap1/fpga.c | 186 ---
arch/arm/mach-omap1/fpga.h | 49 -
arch/arm/mach-omap1/gpio7xx.c | 272 ---
arch/arm/mach-omap1/i2c.c | 14 +-
arch/arm/mach-omap1/io.c | 24 -
arch/arm/mach-omap1/irq.c | 20 +-
arch/arm/mach-omap1/irqs.h | 9 -
arch/arm/mach-omap1/mcbsp.c | 83 -
arch/arm/mach-omap1/mtd-xip.h | 4 -
arch/arm/mach-omap1/mux.c | 52 -
arch/arm/mach-omap1/pm.c | 76 +-
arch/arm/mach-omap1/pm.h | 39 +-
arch/arm/mach-omap1/serial.c | 15 -
arch/arm/mach-omap1/sleep.S | 80 -
arch/arm/mach-omap1/sram-init.c | 7 +-
arch/arm/mach-omap1/usb.c | 34 +-
arch/arm/mach-orion5x/Kconfig | 59 -
arch/arm/mach-orion5x/Makefile | 8 -
arch/arm/mach-orion5x/common.c | 10 -
arch/arm/mach-orion5x/common.h | 2 -
arch/arm/mach-orion5x/db88f5281-setup.c | 376 -----
arch/arm/mach-orion5x/ls_hgl-setup.c | 275 ----
arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c | 172 --
arch/arm/mach-orion5x/rd88f5181l-ge-setup.c | 183 ---
arch/arm/mach-orion5x/rd88f5182-setup.c | 288 ----
arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c | 120 --
arch/arm/mach-orion5x/wnr854t-setup.c | 175 --
arch/arm/mach-orion5x/wrt350n-v2-setup.c | 263 ---
arch/arm/plat-orion/common.c | 31 -
arch/arm/plat-orion/include/plat/common.h | 3 -
drivers/dma/Kconfig | 8 -
drivers/dma/Makefile | 1 -
drivers/dma/iop-adma.c | 1554 ------------------
drivers/dma/iop-adma.h | 914 ----------
drivers/gpio/Kconfig | 10 -
drivers/gpio/Makefile | 1 -
drivers/gpio/gpio-iop.c | 59 -
drivers/i2c/busses/Kconfig | 8 +-
drivers/mfd/Kconfig | 11 +-
drivers/mfd/Makefile | 1 -
drivers/mfd/htc-i2cpld.c | 627 -------
drivers/mmc/host/Kconfig | 13 +-
drivers/mmc/host/Makefile | 1 -
drivers/mmc/host/sdhci-cns3xxx.c | 113 --
drivers/spi/Kconfig | 6 -
drivers/spi/Makefile | 1 -
drivers/spi/spi-omap-100k.c | 490 ------
drivers/spi/spi-omap-uwire.c | 16 +-
drivers/usb/gadget/udc/Kconfig | 2 +-
drivers/usb/gadget/udc/omap_udc.c | 24 +-
drivers/usb/host/Kconfig | 25 +-
drivers/usb/host/ohci-omap.c | 6 +-
drivers/usb/musb/musb_dma.h | 11 +-
drivers/usb/phy/phy-isp1301-omap.c | 91 +-
drivers/video/fbdev/omap/Kconfig | 9 -
drivers/video/fbdev/omap/Makefile | 6 -
drivers/video/fbdev/omap/lcd_h3.c | 82 -
drivers/video/fbdev/omap/lcd_htcherald.c | 59 -
drivers/video/fbdev/omap/lcd_inn1510.c | 69 -
drivers/video/fbdev/omap/lcd_inn1610.c | 99 --
drivers/video/fbdev/omap/lcd_palmtt.c | 65 -
drivers/video/fbdev/omap/lcd_palmz71.c | 59 -
drivers/video/fbdev/omap/lcdc.c | 2 -
drivers/watchdog/wdt285.c | 2 -
include/linux/htcpld.h | 23 -
include/linux/platform_data/leds-omap.h | 19 -
include/linux/soc/ti/omap1-soc.h | 35 -
sound/soc/cirrus/Kconfig | 23 -
sound/soc/cirrus/Makefile | 6 -
sound/soc/cirrus/ep93xx-ac97.c | 446 -----
sound/soc/cirrus/simone.c | 86 -
sound/soc/cirrus/snappercl15.c | 134 --
157 files changed, 60 insertions(+), 18109 deletions(-)
delete mode 100644 arch/arm/configs/cns3420vb_defconfig
delete mode 100644 arch/arm/configs/iop32x_defconfig
delete mode 100644 arch/arm/mach-cns3xxx/Kconfig
delete mode 100644 arch/arm/mach-cns3xxx/Makefile
delete mode 100644 arch/arm/mach-cns3xxx/cns3420vb.c
delete mode 100644 arch/arm/mach-cns3xxx/cns3xxx.h
delete mode 100644 arch/arm/mach-cns3xxx/core.c
delete mode 100644 arch/arm/mach-cns3xxx/core.h
delete mode 100644 arch/arm/mach-cns3xxx/devices.c
delete mode 100644 arch/arm/mach-cns3xxx/devices.h
delete mode 100644 arch/arm/mach-cns3xxx/pcie.c
delete mode 100644 arch/arm/mach-cns3xxx/pm.c
delete mode 100644 arch/arm/mach-cns3xxx/pm.h
delete mode 100644 arch/arm/mach-dove/dove-db-setup.c
delete mode 100644 arch/arm/mach-ep93xx/adssphere.c
delete mode 100644 arch/arm/mach-ep93xx/gesbc9312.c
delete mode 100644 arch/arm/mach-ep93xx/micro9.c
delete mode 100644 arch/arm/mach-ep93xx/simone.c
delete mode 100644 arch/arm/mach-ep93xx/snappercl15.c
delete mode 100644 arch/arm/mach-footbridge/cats-hw.c
delete mode 100644 arch/arm/mach-footbridge/cats-pci.c
delete mode 100644 arch/arm/mach-iop32x/Kconfig
delete mode 100644 arch/arm/mach-iop32x/Makefile
delete mode 100644 arch/arm/mach-iop32x/adma.c
delete mode 100644 arch/arm/mach-iop32x/cp6.c
delete mode 100644 arch/arm/mach-iop32x/em7210.c
delete mode 100644 arch/arm/mach-iop32x/glantank.c
delete mode 100644 arch/arm/mach-iop32x/glantank.h
delete mode 100644 arch/arm/mach-iop32x/gpio-iop32x.h
delete mode 100644 arch/arm/mach-iop32x/hardware.h
delete mode 100644 arch/arm/mach-iop32x/i2c.c
delete mode 100644 arch/arm/mach-iop32x/iop3xx.h
delete mode 100644 arch/arm/mach-iop32x/iq31244.c
delete mode 100644 arch/arm/mach-iop32x/iq31244.h
delete mode 100644 arch/arm/mach-iop32x/iq80321.c
delete mode 100644 arch/arm/mach-iop32x/iq80321.h
delete mode 100644 arch/arm/mach-iop32x/irq.c
delete mode 100644 arch/arm/mach-iop32x/irqs.h
delete mode 100644 arch/arm/mach-iop32x/n2100.c
delete mode 100644 arch/arm/mach-iop32x/n2100.h
delete mode 100644 arch/arm/mach-iop32x/pci.c
delete mode 100644 arch/arm/mach-iop32x/pmu.c
delete mode 100644 arch/arm/mach-iop32x/restart.c
delete mode 100644 arch/arm/mach-iop32x/setup.c
delete mode 100644 arch/arm/mach-iop32x/time.c
delete mode 100644 arch/arm/mach-mv78xx0/db78x00-bp-setup.c
delete mode 100644 arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
delete mode 100644 arch/arm/mach-omap1/board-fsample.c
delete mode 100644 arch/arm/mach-omap1/board-generic.c
delete mode 100644 arch/arm/mach-omap1/board-h2-mmc.c
delete mode 100644 arch/arm/mach-omap1/board-h2.c
delete mode 100644 arch/arm/mach-omap1/board-h2.h
delete mode 100644 arch/arm/mach-omap1/board-h3-mmc.c
delete mode 100644 arch/arm/mach-omap1/board-h3.c
delete mode 100644 arch/arm/mach-omap1/board-h3.h
delete mode 100644 arch/arm/mach-omap1/board-htcherald.c
delete mode 100644 arch/arm/mach-omap1/board-innovator.c
delete mode 100644 arch/arm/mach-omap1/board-nand.c
delete mode 100644 arch/arm/mach-omap1/board-palmtt.c
delete mode 100644 arch/arm/mach-omap1/board-palmz71.c
delete mode 100644 arch/arm/mach-omap1/board-perseus2.c
delete mode 100644 arch/arm/mach-omap1/fpga.c
delete mode 100644 arch/arm/mach-omap1/fpga.h
delete mode 100644 arch/arm/mach-omap1/gpio7xx.c
delete mode 100644 arch/arm/mach-orion5x/db88f5281-setup.c
delete mode 100644 arch/arm/mach-orion5x/ls_hgl-setup.c
delete mode 100644 arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
delete mode 100644 arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
delete mode 100644 arch/arm/mach-orion5x/rd88f5182-setup.c
delete mode 100644 arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
delete mode 100644 arch/arm/mach-orion5x/wnr854t-setup.c
delete mode 100644 arch/arm/mach-orion5x/wrt350n-v2-setup.c
delete mode 100644 drivers/dma/iop-adma.c
delete mode 100644 drivers/dma/iop-adma.h
delete mode 100644 drivers/gpio/gpio-iop.c
delete mode 100644 drivers/mfd/htc-i2cpld.c
delete mode 100644 drivers/mmc/host/sdhci-cns3xxx.c
delete mode 100644 drivers/spi/spi-omap-100k.c
delete mode 100644 drivers/video/fbdev/omap/lcd_h3.c
delete mode 100644 drivers/video/fbdev/omap/lcd_htcherald.c
delete mode 100644 drivers/video/fbdev/omap/lcd_inn1510.c
delete mode 100644 drivers/video/fbdev/omap/lcd_inn1610.c
delete mode 100644 drivers/video/fbdev/omap/lcd_palmtt.c
delete mode 100644 drivers/video/fbdev/omap/lcd_palmz71.c
delete mode 100644 include/linux/htcpld.h
delete mode 100644 include/linux/platform_data/leds-omap.h
delete mode 100644 sound/soc/cirrus/ep93xx-ac97.c
delete mode 100644 sound/soc/cirrus/simone.c
delete mode 100644 sound/soc/cirrus/snappercl15.c
--
2.29.2
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH 14/17] ARM: omap1: remove dead code
[not found] ` <20221019150410.3851944-1-arnd@kernel.org>
@ 2022-10-19 15:03 ` Arnd Bergmann
2022-10-19 17:34 ` Aaro Koskinen
` (3 more replies)
2022-10-19 15:03 ` [PATCH 15/17] fbdev: omapfb: remove unused board support Arnd Bergmann
` (2 subsequent siblings)
3 siblings, 4 replies; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-19 15:03 UTC (permalink / raw)
To: linux-arm-kernel, Paul Walmsley, Aaro Koskinen,
Janusz Krzysztofik, Tony Lindgren
Cc: linux-kernel, Arnd Bergmann, linux-omap, Kevin Hilman,
Mark Brown, Felipe Balbi, Greg Kroah-Hartman, Alan Stern,
Bin Liu, Helge Deller, linux-usb, linux-spi, linux-fbdev,
dri-devel
From: Arnd Bergmann <arnd@arndb.de>
After the removal of the unused board files, I went through the
omap1 code to look for code that no longer has any callers
and remove that.
In particular, support for the omap7xx/omap8xx family is now
completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
arch/arm/mach-omap1/clock_data.c | 17 +-----
arch/arm/mach-omap1/common.h | 8 ---
arch/arm/mach-omap1/devices.c | 58 ++-----------------
arch/arm/mach-omap1/dma.c | 25 +-------
arch/arm/mach-omap1/i2c.c | 14 +----
arch/arm/mach-omap1/io.c | 24 --------
arch/arm/mach-omap1/irq.c | 20 +------
arch/arm/mach-omap1/irqs.h | 9 ---
arch/arm/mach-omap1/mcbsp.c | 83 ---------------------------
arch/arm/mach-omap1/mtd-xip.h | 4 --
arch/arm/mach-omap1/mux.c | 52 -----------------
arch/arm/mach-omap1/pm.c | 76 ++++---------------------
arch/arm/mach-omap1/pm.h | 39 +------------
arch/arm/mach-omap1/serial.c | 15 -----
arch/arm/mach-omap1/sleep.S | 80 --------------------------
arch/arm/mach-omap1/sram-init.c | 7 +--
arch/arm/mach-omap1/usb.c | 34 +++--------
drivers/spi/spi-omap-uwire.c | 16 +-----
drivers/usb/gadget/udc/omap_udc.c | 24 +-------
drivers/usb/host/ohci-omap.c | 6 +-
drivers/usb/musb/musb_dma.h | 11 +---
drivers/usb/phy/phy-isp1301-omap.c | 91 +-----------------------------
drivers/video/fbdev/omap/lcdc.c | 2 -
include/linux/soc/ti/omap1-soc.h | 35 ------------
24 files changed, 39 insertions(+), 711 deletions(-)
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index 96d846c37c43..c58d200e4816 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -720,8 +720,6 @@ int __init omap1_clk_init(void)
cpu_mask |= CK_16XX;
if (cpu_is_omap1510())
cpu_mask |= CK_1510;
- if (cpu_is_omap7xx())
- cpu_mask |= CK_7XX;
if (cpu_is_omap310())
cpu_mask |= CK_310;
@@ -730,9 +728,6 @@ int __init omap1_clk_init(void)
ck_dpll1_p = &ck_dpll1;
ck_ref_p = &ck_ref;
- if (cpu_is_omap7xx())
- ck_ref.rate = 13000000;
-
pr_info("Clocks: ARM_SYSST: 0x%04x DPLL_CTL: 0x%04x ARM_CKCTL: 0x%04x\n",
omap_readw(ARM_SYSST), omap_readw(DPLL_CTL),
omap_readw(ARM_CKCTL));
@@ -771,12 +766,6 @@ int __init omap1_clk_init(void)
}
}
- if (machine_is_omap_perseus2() || machine_is_omap_fsample()) {
- /* Select slicer output as OMAP input clock */
- omap_writew(omap_readw(OMAP7XX_PCC_UPLD_CTRL) & ~0x1,
- OMAP7XX_PCC_UPLD_CTRL);
- }
-
/* Amstrad Delta wants BCLK high when inactive */
if (machine_is_ams_delta())
omap_writel(omap_readl(ULPD_CLOCK_CTRL) |
@@ -784,11 +773,7 @@ int __init omap1_clk_init(void)
ULPD_CLOCK_CTRL);
/* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
- /* (on 730, bit 13 must not be cleared) */
- if (cpu_is_omap7xx())
- omap_writew(omap_readw(ARM_CKCTL) & 0x2fff, ARM_CKCTL);
- else
- omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
+ omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
/* Put DSP/MPUI into reset until needed */
omap_writew(0, ARM_RSTCT1);
diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h
index 5ceff05e15c0..3fd9ed9efb12 100644
--- a/arch/arm/mach-omap1/common.h
+++ b/arch/arm/mach-omap1/common.h
@@ -35,14 +35,6 @@
#include "soc.h"
#include "i2c.h"
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-void omap7xx_map_io(void);
-#else
-static inline void omap7xx_map_io(void)
-{
-}
-#endif
-
#ifdef CONFIG_ARCH_OMAP15XX
void omap1510_fpga_init_irq(void);
void omap15xx_map_io(void);
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index 80e94770582a..42d1631cecc0 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -63,8 +63,6 @@ static void omap_init_rtc(void)
static inline void omap_init_rtc(void) {}
#endif
-static inline void omap_init_mbox(void) { }
-
/*-------------------------------------------------------------------------*/
#if IS_ENABLED(CONFIG_MMC_OMAP)
@@ -73,22 +71,16 @@ static inline void omap1_mmc_mux(struct omap_mmc_platform_data *mmc_controller,
int controller_nr)
{
if (controller_nr == 0) {
- if (cpu_is_omap7xx()) {
- omap_cfg_reg(MMC_7XX_CMD);
- omap_cfg_reg(MMC_7XX_CLK);
- omap_cfg_reg(MMC_7XX_DAT0);
- } else {
- omap_cfg_reg(MMC_CMD);
- omap_cfg_reg(MMC_CLK);
- omap_cfg_reg(MMC_DAT0);
- }
+ omap_cfg_reg(MMC_CMD);
+ omap_cfg_reg(MMC_CLK);
+ omap_cfg_reg(MMC_DAT0);
if (cpu_is_omap1710()) {
omap_cfg_reg(M15_1710_MMC_CLKI);
omap_cfg_reg(P19_1710_MMC_CMDDIR);
omap_cfg_reg(P20_1710_MMC_DATDIR0);
}
- if (mmc_controller->slots[0].wires == 4 && !cpu_is_omap7xx()) {
+ if (mmc_controller->slots[0].wires == 4) {
omap_cfg_reg(MMC_DAT1);
/* NOTE: DAT2 can be on W10 (here) or M15 */
if (!mmc_controller->slots[0].nomux)
@@ -154,8 +146,6 @@ static int __init omap_mmc_add(const char *name, int id, unsigned long base,
res[3].name = "tx";
res[3].flags = IORESOURCE_DMA;
- if (cpu_is_omap7xx())
- data->slots[0].features = MMC_OMAP7XX;
if (cpu_is_omap15xx())
data->slots[0].features = MMC_OMAP15XX;
if (cpu_is_omap16xx())
@@ -224,43 +214,6 @@ void __init omap1_init_mmc(struct omap_mmc_platform_data **mmc_data,
/*-------------------------------------------------------------------------*/
-/* OMAP7xx SPI support */
-#if IS_ENABLED(CONFIG_SPI_OMAP_100K)
-
-struct platform_device omap_spi1 = {
- .name = "omap1_spi100k",
- .id = 1,
-};
-
-struct platform_device omap_spi2 = {
- .name = "omap1_spi100k",
- .id = 2,
-};
-
-static void omap_init_spi100k(void)
-{
- if (!cpu_is_omap7xx())
- return;
-
- omap_spi1.dev.platform_data = ioremap(OMAP7XX_SPI1_BASE, 0x7ff);
- if (omap_spi1.dev.platform_data)
- platform_device_register(&omap_spi1);
-
- omap_spi2.dev.platform_data = ioremap(OMAP7XX_SPI2_BASE, 0x7ff);
- if (omap_spi2.dev.platform_data)
- platform_device_register(&omap_spi2);
-}
-
-#else
-static inline void omap_init_spi100k(void)
-{
-}
-#endif
-
-/*-------------------------------------------------------------------------*/
-
-static inline void omap_init_sti(void) {}
-
/* Numbering for the SPI-capable controllers when used for SPI:
* spi = 1
* uwire = 2
@@ -363,10 +316,7 @@ static int __init omap1_init_devices(void)
* in alphabetical order so they're easier to sort through.
*/
- omap_init_mbox();
omap_init_rtc();
- omap_init_spi100k();
- omap_init_sti();
omap_init_uwire();
omap1_init_rng();
diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c
index c3f280c3c5d7..756966cb715f 100644
--- a/arch/arm/mach-omap1/dma.c
+++ b/arch/arm/mach-omap1/dma.c
@@ -261,22 +261,6 @@ static const struct platform_device_info omap_dma_dev_info = {
.num_res = 1,
};
-/* OMAP730, OMAP850 */
-static const struct dma_slave_map omap7xx_sdma_map[] = {
- { "omap-mcbsp.1", "tx", SDMA_FILTER_PARAM(8) },
- { "omap-mcbsp.1", "rx", SDMA_FILTER_PARAM(9) },
- { "omap-mcbsp.2", "tx", SDMA_FILTER_PARAM(10) },
- { "omap-mcbsp.2", "rx", SDMA_FILTER_PARAM(11) },
- { "mmci-omap.0", "tx", SDMA_FILTER_PARAM(21) },
- { "mmci-omap.0", "rx", SDMA_FILTER_PARAM(22) },
- { "omap_udc", "rx0", SDMA_FILTER_PARAM(26) },
- { "omap_udc", "rx1", SDMA_FILTER_PARAM(27) },
- { "omap_udc", "rx2", SDMA_FILTER_PARAM(28) },
- { "omap_udc", "tx0", SDMA_FILTER_PARAM(29) },
- { "omap_udc", "tx1", SDMA_FILTER_PARAM(30) },
- { "omap_udc", "tx2", SDMA_FILTER_PARAM(31) },
-};
-
/* OMAP1510, OMAP1610*/
static const struct dma_slave_map omap1xxx_sdma_map[] = {
{ "omap-mcbsp.1", "tx", SDMA_FILTER_PARAM(8) },
@@ -371,13 +355,8 @@ static int __init omap1_system_dma_init(void)
p.dma_attr = d;
p.errata = configure_dma_errata();
- if (cpu_is_omap7xx()) {
- p.slave_map = omap7xx_sdma_map;
- p.slavecnt = ARRAY_SIZE(omap7xx_sdma_map);
- } else {
- p.slave_map = omap1xxx_sdma_map;
- p.slavecnt = ARRAY_SIZE(omap1xxx_sdma_map);
- }
+ p.slave_map = omap1xxx_sdma_map;
+ p.slavecnt = ARRAY_SIZE(omap1xxx_sdma_map);
ret = platform_device_add_data(pdev, &p, sizeof(p));
if (ret) {
diff --git a/arch/arm/mach-omap1/i2c.c b/arch/arm/mach-omap1/i2c.c
index 22f945360599..94d3e7883e02 100644
--- a/arch/arm/mach-omap1/i2c.c
+++ b/arch/arm/mach-omap1/i2c.c
@@ -25,13 +25,8 @@ static struct platform_device omap_i2c_devices[1] = {
static void __init omap1_i2c_mux_pins(int bus_id)
{
- if (cpu_is_omap7xx()) {
- omap_cfg_reg(I2C_7XX_SDA);
- omap_cfg_reg(I2C_7XX_SCL);
- } else {
- omap_cfg_reg(I2C_SDA);
- omap_cfg_reg(I2C_SCL);
- }
+ omap_cfg_reg(I2C_SDA);
+ omap_cfg_reg(I2C_SCL);
}
int __init omap_i2c_add_bus(struct omap_i2c_bus_platform_data *pdata,
@@ -68,10 +63,7 @@ int __init omap_i2c_add_bus(struct omap_i2c_bus_platform_data *pdata,
/* how the cpu bus is wired up differs for 7xx only */
- if (cpu_is_omap7xx())
- pdata->flags |= OMAP_I2C_FLAG_BUS_SHIFT_1;
- else
- pdata->flags |= OMAP_I2C_FLAG_BUS_SHIFT_2;
+ pdata->flags |= OMAP_I2C_FLAG_BUS_SHIFT_2;
pdev->dev.platform_data = pdata;
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index d2db9b8aed3f..72657413795f 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -31,22 +31,6 @@ static struct map_desc omap_io_desc[] __initdata = {
}
};
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
-static struct map_desc omap7xx_io_desc[] __initdata = {
- {
- .virtual = OMAP7XX_DSP_BASE,
- .pfn = __phys_to_pfn(OMAP7XX_DSP_START),
- .length = OMAP7XX_DSP_SIZE,
- .type = MT_DEVICE
- }, {
- .virtual = OMAP7XX_DSPREG_BASE,
- .pfn = __phys_to_pfn(OMAP7XX_DSPREG_START),
- .length = OMAP7XX_DSPREG_SIZE,
- .type = MT_DEVICE
- }
-};
-#endif
-
#ifdef CONFIG_ARCH_OMAP15XX
static struct map_desc omap1510_io_desc[] __initdata = {
{
@@ -87,14 +71,6 @@ static void __init omap1_map_common_io(void)
iotable_init(omap_io_desc, ARRAY_SIZE(omap_io_desc));
}
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
-void __init omap7xx_map_io(void)
-{
- omap1_map_common_io();
- iotable_init(omap7xx_io_desc, ARRAY_SIZE(omap7xx_io_desc));
-}
-#endif
-
#ifdef CONFIG_ARCH_OMAP15XX
void __init omap15xx_map_io(void)
{
diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c
index 70868e9f19ac..9ccc784fd614 100644
--- a/arch/arm/mach-omap1/irq.c
+++ b/arch/arm/mach-omap1/irq.c
@@ -110,14 +110,6 @@ static void omap_irq_set_cfg(int irq, int fiq, int priority, int trigger)
irq_bank_writel(val, bank, offset);
}
-#if defined (CONFIG_ARCH_OMAP730) || defined (CONFIG_ARCH_OMAP850)
-static struct omap_irq_bank omap7xx_irq_banks[] = {
- { .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3f8e22f },
- { .base_reg = OMAP_IH2_BASE, .trigger_map = 0xfdb9c1f2 },
- { .base_reg = OMAP_IH2_BASE + 0x100, .trigger_map = 0x800040f3 },
-};
-#endif
-
#ifdef CONFIG_ARCH_OMAP15XX
static struct omap_irq_bank omap1510_irq_banks[] = {
{ .base_reg = OMAP_IH1_BASE, .trigger_map = 0xb3febfff },
@@ -194,12 +186,6 @@ void __init omap1_init_irq(void)
int i, j, irq_base;
unsigned long nr_irqs;
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
- if (cpu_is_omap7xx()) {
- irq_banks = omap7xx_irq_banks;
- irq_bank_count = ARRAY_SIZE(omap7xx_irq_banks);
- }
-#endif
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap1510()) {
irq_banks = omap1510_irq_banks;
@@ -230,7 +216,7 @@ void __init omap1_init_irq(void)
pr_warn("Couldn't allocate IRQ numbers\n");
irq_base = 0;
}
- omap_l2_irq = cpu_is_omap7xx() ? irq_base + 1 : irq_base;
+ omap_l2_irq = irq_base;
omap_l2_irq -= NR_IRQS_LEGACY;
domain = irq_domain_add_legacy(NULL, nr_irqs, irq_base, 0,
@@ -249,10 +235,6 @@ void __init omap1_init_irq(void)
irq_bank_writel(0x03, 0, IRQ_CONTROL_REG_OFFSET);
irq_bank_writel(0x03, 1, IRQ_CONTROL_REG_OFFSET);
- /* Enable interrupts in global mask */
- if (cpu_is_omap7xx())
- irq_bank_writel(0x0, 0, IRQ_GMR_REG_OFFSET);
-
/* Install the interrupt handlers for each bank */
for (i = 0; i < irq_bank_count; i++) {
for (j = i * 32; j < (i + 1) * 32; j++) {
diff --git a/arch/arm/mach-omap1/irqs.h b/arch/arm/mach-omap1/irqs.h
index 2851acfe5ff3..3ab7050b1b6b 100644
--- a/arch/arm/mach-omap1/irqs.h
+++ b/arch/arm/mach-omap1/irqs.h
@@ -231,15 +231,6 @@
#define IH_MPUIO_BASE (OMAP_MAX_GPIO_LINES + IH_GPIO_BASE)
#define OMAP_IRQ_END (IH_MPUIO_BASE + 16)
-/* External FPGA handles interrupts on Innovator boards */
-#define OMAP_FPGA_IRQ_BASE (OMAP_IRQ_END)
-#ifdef CONFIG_MACH_OMAP_INNOVATOR
-#define OMAP_FPGA_NR_IRQS 24
-#else
-#define OMAP_FPGA_NR_IRQS 0
-#endif
-#define OMAP_FPGA_IRQ_END (OMAP_FPGA_IRQ_BASE + OMAP_FPGA_NR_IRQS)
-
#define OMAP_IRQ_BIT(irq) (1 << ((irq - NR_IRQS_LEGACY) % 32))
#ifdef CONFIG_FIQ
diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index 05c25c432449..72e399ec5ed9 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -89,83 +89,6 @@ static struct omap_mcbsp_ops omap1_mcbsp_ops = {
#define OMAP1610_MCBSP2_BASE 0xfffb1000
#define OMAP1610_MCBSP3_BASE 0xe1017000
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-struct resource omap7xx_mcbsp_res[][6] = {
- {
- {
- .start = OMAP7XX_MCBSP1_BASE,
- .end = OMAP7XX_MCBSP1_BASE + SZ_256,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "rx",
- .start = INT_7XX_McBSP1RX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "tx",
- .start = INT_7XX_McBSP1TX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "rx",
- .start = 9,
- .flags = IORESOURCE_DMA,
- },
- {
- .name = "tx",
- .start = 8,
- .flags = IORESOURCE_DMA,
- },
- },
- {
- {
- .start = OMAP7XX_MCBSP2_BASE,
- .end = OMAP7XX_MCBSP2_BASE + SZ_256,
- .flags = IORESOURCE_MEM,
- },
- {
- .name = "rx",
- .start = INT_7XX_McBSP2RX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "tx",
- .start = INT_7XX_McBSP2TX,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "rx",
- .start = 11,
- .flags = IORESOURCE_DMA,
- },
- {
- .name = "tx",
- .start = 10,
- .flags = IORESOURCE_DMA,
- },
- },
-};
-
-#define omap7xx_mcbsp_res_0 omap7xx_mcbsp_res[0]
-
-static struct omap_mcbsp_platform_data omap7xx_mcbsp_pdata[] = {
- {
- .ops = &omap1_mcbsp_ops,
- },
- {
- .ops = &omap1_mcbsp_ops,
- },
-};
-#define OMAP7XX_MCBSP_RES_SZ ARRAY_SIZE(omap7xx_mcbsp_res[1])
-#define OMAP7XX_MCBSP_COUNT ARRAY_SIZE(omap7xx_mcbsp_res)
-#else
-#define omap7xx_mcbsp_res_0 NULL
-#define omap7xx_mcbsp_pdata NULL
-#define OMAP7XX_MCBSP_RES_SZ 0
-#define OMAP7XX_MCBSP_COUNT 0
-#endif
-
#ifdef CONFIG_ARCH_OMAP15XX
struct resource omap15xx_mcbsp_res[][6] = {
{
@@ -418,12 +341,6 @@ static int __init omap1_mcbsp_init(void)
if (!cpu_class_is_omap1())
return -ENODEV;
- if (cpu_is_omap7xx())
- omap_mcbsp_register_board_cfg(omap7xx_mcbsp_res_0,
- OMAP7XX_MCBSP_RES_SZ,
- omap7xx_mcbsp_pdata,
- OMAP7XX_MCBSP_COUNT);
-
if (cpu_is_omap15xx())
omap_mcbsp_register_board_cfg(omap15xx_mcbsp_res_0,
OMAP15XX_MCBSP_RES_SZ,
diff --git a/arch/arm/mach-omap1/mtd-xip.h b/arch/arm/mach-omap1/mtd-xip.h
index 5ae312ff08a1..cbeda46dd526 100644
--- a/arch/arm/mach-omap1/mtd-xip.h
+++ b/arch/arm/mach-omap1/mtd-xip.h
@@ -42,11 +42,7 @@ static inline unsigned long xip_omap_mpu_timer_read(int nr)
* (see linux/mtd/xip.h)
*/
-#ifdef CONFIG_MACH_OMAP_PERSEUS2
-#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 7)
-#else
#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 6)
-#endif
/*
* xip_cpu_idle() is used when waiting for a delay equal or larger than
diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c
index 2d9458ff1d29..4456fbc8aa3d 100644
--- a/arch/arm/mach-omap1/mux.c
+++ b/arch/arm/mach-omap1/mux.c
@@ -21,52 +21,6 @@
static struct omap_mux_cfg arch_mux_cfg;
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
-static struct pin_config omap7xx_pins[] = {
-MUX_CFG_7XX("E2_7XX_KBR0", 12, 21, 0, 20, 1, 0)
-MUX_CFG_7XX("J7_7XX_KBR1", 12, 25, 0, 24, 1, 0)
-MUX_CFG_7XX("E1_7XX_KBR2", 12, 29, 0, 28, 1, 0)
-MUX_CFG_7XX("F3_7XX_KBR3", 13, 1, 0, 0, 1, 0)
-MUX_CFG_7XX("D2_7XX_KBR4", 13, 5, 0, 4, 1, 0)
-MUX_CFG_7XX("C2_7XX_KBC0", 13, 9, 0, 8, 1, 0)
-MUX_CFG_7XX("D3_7XX_KBC1", 13, 13, 0, 12, 1, 0)
-MUX_CFG_7XX("E4_7XX_KBC2", 13, 17, 0, 16, 1, 0)
-MUX_CFG_7XX("F4_7XX_KBC3", 13, 21, 0, 20, 1, 0)
-MUX_CFG_7XX("E3_7XX_KBC4", 13, 25, 0, 24, 1, 0)
-
-MUX_CFG_7XX("AA17_7XX_USB_DM", 2, 21, 0, 20, 0, 0)
-MUX_CFG_7XX("W16_7XX_USB_PU_EN", 2, 25, 0, 24, 0, 0)
-MUX_CFG_7XX("W17_7XX_USB_VBUSI", 2, 29, 6, 28, 1, 0)
-MUX_CFG_7XX("W18_7XX_USB_DMCK_OUT",3, 3, 1, 2, 0, 0)
-MUX_CFG_7XX("W19_7XX_USB_DCRST", 3, 7, 1, 6, 0, 0)
-
-/* MMC Pins */
-MUX_CFG_7XX("MMC_7XX_CMD", 2, 9, 0, 8, 1, 0)
-MUX_CFG_7XX("MMC_7XX_CLK", 2, 13, 0, 12, 1, 0)
-MUX_CFG_7XX("MMC_7XX_DAT0", 2, 17, 0, 16, 1, 0)
-
-/* I2C interface */
-MUX_CFG_7XX("I2C_7XX_SCL", 5, 1, 0, 0, 1, 0)
-MUX_CFG_7XX("I2C_7XX_SDA", 5, 5, 0, 0, 1, 0)
-
-/* SPI pins */
-MUX_CFG_7XX("SPI_7XX_1", 6, 5, 4, 4, 1, 0)
-MUX_CFG_7XX("SPI_7XX_2", 6, 9, 4, 8, 1, 0)
-MUX_CFG_7XX("SPI_7XX_3", 6, 13, 4, 12, 1, 0)
-MUX_CFG_7XX("SPI_7XX_4", 6, 17, 4, 16, 1, 0)
-MUX_CFG_7XX("SPI_7XX_5", 8, 25, 0, 24, 0, 0)
-MUX_CFG_7XX("SPI_7XX_6", 9, 5, 0, 4, 0, 0)
-
-/* UART pins */
-MUX_CFG_7XX("UART_7XX_1", 3, 21, 0, 20, 0, 0)
-MUX_CFG_7XX("UART_7XX_2", 8, 1, 6, 0, 0, 0)
-};
-#define OMAP7XX_PINS_SZ ARRAY_SIZE(omap7xx_pins)
-#else
-#define omap7xx_pins NULL
-#define OMAP7XX_PINS_SZ 0
-#endif /* CONFIG_ARCH_OMAP730 || CONFIG_ARCH_OMAP850 */
-
#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX)
static struct pin_config omap1xxx_pins[] = {
/*
@@ -489,12 +443,6 @@ EXPORT_SYMBOL(omap_cfg_reg);
int __init omap1_mux_init(void)
{
- if (cpu_is_omap7xx()) {
- arch_mux_cfg.pins = omap7xx_pins;
- arch_mux_cfg.size = OMAP7XX_PINS_SZ;
- arch_mux_cfg.cfg_reg = omap1_cfg_reg;
- }
-
if (cpu_is_omap15xx() || cpu_is_omap16xx()) {
arch_mux_cfg.pins = omap1xxx_pins;
arch_mux_cfg.size = OMAP1XXX_PINS_SZ;
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index fce7d2b572bf..9761d8404949 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -69,7 +69,6 @@
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
static unsigned short dsp_sleep_save[DSP_SLEEP_SAVE_SIZE];
static unsigned short ulpd_sleep_save[ULPD_SLEEP_SAVE_SIZE];
-static unsigned int mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_SIZE];
static unsigned int mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_SIZE];
static unsigned int mpui1610_sleep_save[MPUI1610_SLEEP_SAVE_SIZE];
@@ -166,10 +165,7 @@ static void omap_pm_wakeup_setup(void)
* drivers must still separately call omap_set_gpio_wakeup() to
* wake up to a GPIO interrupt.
*/
- if (cpu_is_omap7xx())
- level1_wake = OMAP_IRQ_BIT(INT_7XX_GPIO_BANK1) |
- OMAP_IRQ_BIT(INT_7XX_IH2_IRQ);
- else if (cpu_is_omap15xx())
+ if (cpu_is_omap15xx())
level1_wake = OMAP_IRQ_BIT(INT_GPIO_BANK1) |
OMAP_IRQ_BIT(INT_1510_IH2_IRQ);
else if (cpu_is_omap16xx())
@@ -178,12 +174,7 @@ static void omap_pm_wakeup_setup(void)
omap_writel(~level1_wake, OMAP_IH1_MIR);
- if (cpu_is_omap7xx()) {
- omap_writel(~level2_wake, OMAP_IH2_0_MIR);
- omap_writel(~(OMAP_IRQ_BIT(INT_7XX_WAKE_UP_REQ) |
- OMAP_IRQ_BIT(INT_7XX_MPUIO_KEYPAD)),
- OMAP_IH2_1_MIR);
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
level2_wake |= OMAP_IRQ_BIT(INT_KEYBOARD);
omap_writel(~level2_wake, OMAP_IH2_MIR);
} else if (cpu_is_omap16xx()) {
@@ -236,17 +227,7 @@ void omap1_pm_suspend(void)
* Save interrupt, MPUI, ARM and UPLD control registers.
*/
- if (cpu_is_omap7xx()) {
- MPUI7XX_SAVE(OMAP_IH1_MIR);
- MPUI7XX_SAVE(OMAP_IH2_0_MIR);
- MPUI7XX_SAVE(OMAP_IH2_1_MIR);
- MPUI7XX_SAVE(MPUI_CTRL);
- MPUI7XX_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI7XX_SAVE(MPUI_DSP_API_CONFIG);
- MPUI7XX_SAVE(EMIFS_CONFIG);
- MPUI7XX_SAVE(EMIFF_SDRAM_CONFIG);
-
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
MPUI1510_SAVE(OMAP_IH1_MIR);
MPUI1510_SAVE(OMAP_IH2_MIR);
MPUI1510_SAVE(MPUI_CTRL);
@@ -288,9 +269,8 @@ void omap1_pm_suspend(void)
/* stop DSP */
omap_writew(omap_readw(ARM_RSTCT1) & ~(1 << DSP_EN), ARM_RSTCT1);
- /* shut down dsp_ck */
- if (!cpu_is_omap7xx())
- omap_writew(omap_readw(ARM_CKCTL) & ~(1 << EN_DSPCK), ARM_CKCTL);
+ /* shut down dsp_ck */
+ omap_writew(omap_readw(ARM_CKCTL) & ~(1 << EN_DSPCK), ARM_CKCTL);
/* temporarily enabling api_ck to access DSP registers */
omap_writew(omap_readw(ARM_IDLECT2) | 1 << EN_APICK, ARM_IDLECT2);
@@ -366,13 +346,7 @@ void omap1_pm_suspend(void)
ULPD_RESTORE(ULPD_CLOCK_CTRL);
ULPD_RESTORE(ULPD_STATUS_REQ);
- if (cpu_is_omap7xx()) {
- MPUI7XX_RESTORE(EMIFS_CONFIG);
- MPUI7XX_RESTORE(EMIFF_SDRAM_CONFIG);
- MPUI7XX_RESTORE(OMAP_IH1_MIR);
- MPUI7XX_RESTORE(OMAP_IH2_0_MIR);
- MPUI7XX_RESTORE(OMAP_IH2_1_MIR);
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
MPUI1510_RESTORE(MPUI_CTRL);
MPUI1510_RESTORE(MPUI_DSP_BOOT_CONFIG);
MPUI1510_RESTORE(MPUI_DSP_API_CONFIG);
@@ -433,14 +407,7 @@ static int omap_pm_debug_show(struct seq_file *m, void *v)
ULPD_SAVE(ULPD_DPLL_CTRL);
ULPD_SAVE(ULPD_POWER_CTRL);
- if (cpu_is_omap7xx()) {
- MPUI7XX_SAVE(MPUI_CTRL);
- MPUI7XX_SAVE(MPUI_DSP_STATUS);
- MPUI7XX_SAVE(MPUI_DSP_BOOT_CONFIG);
- MPUI7XX_SAVE(MPUI_DSP_API_CONFIG);
- MPUI7XX_SAVE(EMIFF_SDRAM_CONFIG);
- MPUI7XX_SAVE(EMIFS_CONFIG);
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
MPUI1510_SAVE(MPUI_CTRL);
MPUI1510_SAVE(MPUI_DSP_STATUS);
MPUI1510_SAVE(MPUI_DSP_BOOT_CONFIG);
@@ -486,21 +453,7 @@ static int omap_pm_debug_show(struct seq_file *m, void *v)
ULPD_SHOW(ULPD_STATUS_REQ),
ULPD_SHOW(ULPD_POWER_CTRL));
- if (cpu_is_omap7xx()) {
- seq_printf(m,
- "MPUI7XX_CTRL_REG 0x%-8x \n"
- "MPUI7XX_DSP_STATUS_REG: 0x%-8x \n"
- "MPUI7XX_DSP_BOOT_CONFIG_REG: 0x%-8x \n"
- "MPUI7XX_DSP_API_CONFIG_REG: 0x%-8x \n"
- "MPUI7XX_SDRAM_CONFIG_REG: 0x%-8x \n"
- "MPUI7XX_EMIFS_CONFIG_REG: 0x%-8x \n",
- MPUI7XX_SHOW(MPUI_CTRL),
- MPUI7XX_SHOW(MPUI_DSP_STATUS),
- MPUI7XX_SHOW(MPUI_DSP_BOOT_CONFIG),
- MPUI7XX_SHOW(MPUI_DSP_API_CONFIG),
- MPUI7XX_SHOW(EMIFF_SDRAM_CONFIG),
- MPUI7XX_SHOW(EMIFS_CONFIG));
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
seq_printf(m,
"MPUI1510_CTRL_REG 0x%-8x \n"
"MPUI1510_DSP_STATUS_REG: 0x%-8x \n"
@@ -634,10 +587,7 @@ static int __init omap_pm_init(void)
* These routines need to be in SRAM as that's the only
* memory the MPU can see when it wakes up.
*/
- if (cpu_is_omap7xx()) {
- omap_sram_suspend = omap_sram_push(omap7xx_cpu_suspend,
- omap7xx_cpu_suspend_sz);
- } else if (cpu_is_omap15xx()) {
+ if (cpu_is_omap15xx()) {
omap_sram_suspend = omap_sram_push(omap1510_cpu_suspend,
omap1510_cpu_suspend_sz);
} else if (cpu_is_omap16xx()) {
@@ -652,9 +602,7 @@ static int __init omap_pm_init(void)
arm_pm_idle = omap1_pm_idle;
- if (cpu_is_omap7xx())
- irq = INT_7XX_WAKE_UP_REQ;
- else if (cpu_is_omap16xx())
+ if (cpu_is_omap16xx())
irq = INT_1610_WAKE_UP_REQ;
else
irq = -1;
@@ -673,9 +621,7 @@ static int __init omap_pm_init(void)
omap_writew(ULPD_POWER_CTRL_REG_VAL, ULPD_POWER_CTRL);
/* Configure IDLECT3 */
- if (cpu_is_omap7xx())
- omap_writel(OMAP7XX_IDLECT3_VAL, OMAP7XX_IDLECT3);
- else if (cpu_is_omap16xx())
+ if (cpu_is_omap16xx())
omap_writel(OMAP1610_IDLECT3_VAL, OMAP1610_IDLECT3);
suspend_set_ops(&omap_pm_ops);
diff --git a/arch/arm/mach-omap1/pm.h b/arch/arm/mach-omap1/pm.h
index d9165709c532..146dbfd90ba1 100644
--- a/arch/arm/mach-omap1/pm.h
+++ b/arch/arm/mach-omap1/pm.h
@@ -100,15 +100,7 @@
#define OMAP1610_IDLECT3 0xfffece24
#define OMAP1610_IDLE_LOOP_REQUEST 0x0400
-#define OMAP7XX_IDLECT1_SLEEP_VAL 0x16c7
-#define OMAP7XX_IDLECT2_SLEEP_VAL 0x09c7
-#define OMAP7XX_IDLECT3_VAL 0x3f
-#define OMAP7XX_IDLECT3 0xfffece24
-#define OMAP7XX_IDLE_LOOP_REQUEST 0x0C00
-
-#if !defined(CONFIG_ARCH_OMAP730) && \
- !defined(CONFIG_ARCH_OMAP850) && \
- !defined(CONFIG_ARCH_OMAP15XX) && \
+#if !defined(CONFIG_ARCH_OMAP15XX) && \
!defined(CONFIG_ARCH_OMAP16XX)
#warning "Power management for this processor not implemented yet"
#endif
@@ -125,17 +117,13 @@ extern void allow_idle_sleep(void);
extern void omap1_pm_idle(void);
extern void omap1_pm_suspend(void);
-extern void omap7xx_cpu_suspend(unsigned long, unsigned long);
extern void omap1510_cpu_suspend(unsigned long, unsigned long);
extern void omap1610_cpu_suspend(unsigned long, unsigned long);
-extern void omap7xx_idle_loop_suspend(void);
extern void omap1510_idle_loop_suspend(void);
extern void omap1610_idle_loop_suspend(void);
-extern unsigned int omap7xx_cpu_suspend_sz;
extern unsigned int omap1510_cpu_suspend_sz;
extern unsigned int omap1610_cpu_suspend_sz;
-extern unsigned int omap7xx_idle_loop_suspend_sz;
extern unsigned int omap1510_idle_loop_suspend_sz;
extern unsigned int omap1610_idle_loop_suspend_sz;
@@ -158,10 +146,6 @@ extern void omap_serial_wake_trigger(int enable);
#define ULPD_RESTORE(x) omap_writew((ulpd_sleep_save[ULPD_SLEEP_SAVE_##x]), (x))
#define ULPD_SHOW(x) ulpd_sleep_save[ULPD_SLEEP_SAVE_##x]
-#define MPUI7XX_SAVE(x) mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x] = omap_readl(x)
-#define MPUI7XX_RESTORE(x) omap_writel((mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x]), (x))
-#define MPUI7XX_SHOW(x) mpui7xx_sleep_save[MPUI7XX_SLEEP_SAVE_##x]
-
#define MPUI1510_SAVE(x) mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_##x] = omap_readl(x)
#define MPUI1510_RESTORE(x) omap_writel((mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_##x]), (x))
#define MPUI1510_SHOW(x) mpui1510_sleep_save[MPUI1510_SLEEP_SAVE_##x]
@@ -235,27 +219,6 @@ enum mpui1510_save_state {
#endif
};
-enum mpui7xx_save_state {
- MPUI7XX_SLEEP_SAVE_START = 0,
- /*
- * MPUI registers 32 bits
- */
- MPUI7XX_SLEEP_SAVE_MPUI_CTRL,
- MPUI7XX_SLEEP_SAVE_MPUI_DSP_BOOT_CONFIG,
- MPUI7XX_SLEEP_SAVE_MPUI_DSP_API_CONFIG,
- MPUI7XX_SLEEP_SAVE_MPUI_DSP_STATUS,
- MPUI7XX_SLEEP_SAVE_EMIFF_SDRAM_CONFIG,
- MPUI7XX_SLEEP_SAVE_EMIFS_CONFIG,
- MPUI7XX_SLEEP_SAVE_OMAP_IH1_MIR,
- MPUI7XX_SLEEP_SAVE_OMAP_IH2_0_MIR,
- MPUI7XX_SLEEP_SAVE_OMAP_IH2_1_MIR,
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
- MPUI7XX_SLEEP_SAVE_SIZE
-#else
- MPUI7XX_SLEEP_SAVE_SIZE = 0
-#endif
-};
-
enum mpui1610_save_state {
MPUI1610_SLEEP_SAVE_START = 0,
/*
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 88928fc33b2e..c7f590645774 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -106,13 +106,6 @@ void __init omap_serial_init(void)
{
int i;
- if (cpu_is_omap7xx()) {
- serial_platform_data[0].regshift = 0;
- serial_platform_data[1].regshift = 0;
- serial_platform_data[0].irq = INT_7XX_UART_MODEM_1;
- serial_platform_data[1].irq = INT_7XX_UART_MODEM_IRDA_2;
- }
-
if (cpu_is_omap15xx()) {
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
@@ -120,14 +113,6 @@ void __init omap_serial_init(void)
}
for (i = 0; i < ARRAY_SIZE(serial_platform_data) - 1; i++) {
-
- /* Don't look at UARTs higher than 2 for omap7xx */
- if (cpu_is_omap7xx() && i > 1) {
- serial_platform_data[i].membase = NULL;
- serial_platform_data[i].mapbase = 0;
- continue;
- }
-
/* Static mapping, never released */
serial_platform_data[i].membase =
ioremap(serial_platform_data[i].mapbase, SZ_2K);
diff --git a/arch/arm/mach-omap1/sleep.S b/arch/arm/mach-omap1/sleep.S
index f111b79512ce..6192f52d531a 100644
--- a/arch/arm/mach-omap1/sleep.S
+++ b/arch/arm/mach-omap1/sleep.S
@@ -61,86 +61,6 @@
*
*/
-#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
- .align 3
-ENTRY(omap7xx_cpu_suspend)
-
- @ save registers on stack
- stmfd sp!, {r0 - r12, lr}
-
- @ Drain write cache
- mov r4, #0
- mcr p15, 0, r0, c7, c10, 4
- nop
-
- @ load base address of Traffic Controller
- mov r6, #TCMIF_ASM_BASE & 0xff000000
- orr r6, r6, #TCMIF_ASM_BASE & 0x00ff0000
- orr r6, r6, #TCMIF_ASM_BASE & 0x0000ff00
-
- @ prepare to put SDRAM into self-refresh manually
- ldr r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
- orr r9, r7, #SELF_REFRESH_MODE & 0xff000000
- orr r9, r9, #SELF_REFRESH_MODE & 0x000000ff
- str r9, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
-
- @ prepare to put EMIFS to Sleep
- ldr r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
- orr r9, r8, #IDLE_EMIFS_REQUEST & 0xff
- str r9, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ load base address of ARM_IDLECT1 and ARM_IDLECT2
- mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x00ff0000
- orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
-
- @ turn off clock domains
- @ do not disable PERCK (0x04)
- mov r5, #OMAP7XX_IDLECT2_SLEEP_VAL & 0xff
- orr r5, r5, #OMAP7XX_IDLECT2_SLEEP_VAL & 0xff00
- strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
-
- @ request ARM idle
- mov r3, #OMAP7XX_IDLECT1_SLEEP_VAL & 0xff
- orr r3, r3, #OMAP7XX_IDLECT1_SLEEP_VAL & 0xff00
- strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- @ disable instruction cache
- mrc p15, 0, r9, c1, c0, 0
- bic r2, r9, #0x1000
- mcr p15, 0, r2, c1, c0, 0
- nop
-
-/*
- * Let's wait for the next wake up event to wake us up. r0 can't be
- * used here because r0 holds ARM_IDLECT1
- */
- mov r2, #0
- mcr p15, 0, r2, c7, c0, 4 @ wait for interrupt
-/*
- * omap7xx_cpu_suspend()'s resume point.
- *
- * It will just start executing here, so we'll restore stuff from the
- * stack.
- */
- @ re-enable Icache
- mcr p15, 0, r9, c1, c0, 0
-
- @ reset the ARM_IDLECT1 and ARM_IDLECT2.
- strh r1, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
- strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
-
- @ Restore EMIFF controls
- str r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
- str r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
-
- @ restore regs and return
- ldmfd sp!, {r0 - r12, pc}
-
-ENTRY(omap7xx_cpu_suspend_sz)
- .word . - omap7xx_cpu_suspend
-#endif /* CONFIG_ARCH_OMAP730 || CONFIG_ARCH_OMAP850 */
-
#ifdef CONFIG_ARCH_OMAP15XX
.align 3
ENTRY(omap1510_cpu_suspend)
diff --git a/arch/arm/mach-omap1/sram-init.c b/arch/arm/mach-omap1/sram-init.c
index 27c42e2a21cc..79b5a24420f6 100644
--- a/arch/arm/mach-omap1/sram-init.c
+++ b/arch/arm/mach-omap1/sram-init.c
@@ -95,9 +95,7 @@ static void __init omap_detect_and_map_sram(void)
omap_sram_skip = SRAM_BOOTLOADER_SZ;
omap_sram_start = OMAP1_SRAM_PA;
- if (cpu_is_omap7xx())
- omap_sram_size = 0x32000; /* 200K */
- else if (cpu_is_omap15xx())
+ if (cpu_is_omap15xx())
omap_sram_size = 0x30000; /* 192K */
else if (cpu_is_omap1610() || cpu_is_omap1611() ||
cpu_is_omap1621() || cpu_is_omap1710())
@@ -135,9 +133,6 @@ static void (*_omap_sram_reprogram_clock)(u32 dpllctl, u32 ckctl);
void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl)
{
BUG_ON(!_omap_sram_reprogram_clock);
- /* On 730, bit 13 must always be 1 */
- if (cpu_is_omap7xx())
- ckctl |= 0x2000;
_omap_sram_reprogram_clock(dpllctl, ckctl);
}
diff --git a/arch/arm/mach-omap1/usb.c b/arch/arm/mach-omap1/usb.c
index 0119f3ddb7a6..08d42abc4a0f 100644
--- a/arch/arm/mach-omap1/usb.c
+++ b/arch/arm/mach-omap1/usb.c
@@ -190,12 +190,6 @@ static struct platform_device udc_device = {
static inline void udc_device_init(struct omap_usb_config *pdata)
{
- /* IRQ numbers for omap7xx */
- if(cpu_is_omap7xx()) {
- udc_resources[1].start = INT_7XX_USB_GENI;
- udc_resources[2].start = INT_7XX_USB_NON_ISO;
- udc_resources[3].start = INT_7XX_USB_ISO;
- }
pdata->udc_device = &udc_device;
}
@@ -238,8 +232,6 @@ static inline void ohci_device_init(struct omap_usb_config *pdata)
if (!IS_ENABLED(CONFIG_USB_OHCI_HCD))
return;
- if (cpu_is_omap7xx())
- ohci_resources[1].start = INT_7XX_USB_HHC_1;
pdata->ohci_device = &ohci_device;
pdata->ocpi_enable = &ocpi_enable;
}
@@ -267,8 +259,6 @@ static struct platform_device otg_device = {
static inline void otg_device_init(struct omap_usb_config *pdata)
{
- if (cpu_is_omap7xx())
- otg_resources[1].start = INT_7XX_USB_OTG;
pdata->otg_device = &otg_device;
}
@@ -297,14 +287,7 @@ static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
}
if (is_device) {
- if (cpu_is_omap7xx()) {
- omap_cfg_reg(AA17_7XX_USB_DM);
- omap_cfg_reg(W16_7XX_USB_PU_EN);
- omap_cfg_reg(W17_7XX_USB_VBUSI);
- omap_cfg_reg(W18_7XX_USB_DMCK_OUT);
- omap_cfg_reg(W19_7XX_USB_DCRST);
- } else
- omap_cfg_reg(W4_USB_PUEN);
+ omap_cfg_reg(W4_USB_PUEN);
}
if (nwires == 2) {
@@ -324,14 +307,11 @@ static u32 __init omap1_usb0_init(unsigned nwires, unsigned is_device)
* - OTG support on this port not yet written
*/
- /* Don't do this for omap7xx -- it causes USB to not work correctly */
- if (!cpu_is_omap7xx()) {
- l = omap_readl(USB_TRANSCEIVER_CTRL);
- l &= ~(7 << 4);
- if (!is_device)
- l |= (3 << 1);
- omap_writel(l, USB_TRANSCEIVER_CTRL);
- }
+ l = omap_readl(USB_TRANSCEIVER_CTRL);
+ l &= ~(7 << 4);
+ if (!is_device)
+ l |= (3 << 1);
+ omap_writel(l, USB_TRANSCEIVER_CTRL);
return 3 << 16;
}
@@ -698,7 +678,7 @@ void __init omap1_usb_init(struct omap_usb_config *_pdata)
ohci_device_init(pdata);
otg_device_init(pdata);
- if (cpu_is_omap7xx() || cpu_is_omap16xx())
+ if (cpu_is_omap16xx())
omap_otg_init(pdata);
else if (cpu_is_omap15xx())
omap_1510_usb_init(pdata);
diff --git a/drivers/spi/spi-omap-uwire.c b/drivers/spi/spi-omap-uwire.c
index 29198e6815b2..20c87163d612 100644
--- a/drivers/spi/spi-omap-uwire.c
+++ b/drivers/spi/spi-omap-uwire.c
@@ -99,7 +99,7 @@ struct uwire_state {
* Or, put it in a structure which is used throughout the driver;
* that avoids having to issue two loads for each bit of static data.
*/
-static unsigned int uwire_idx_shift;
+static unsigned int uwire_idx_shift = 2;
static void __iomem *uwire_base;
static inline void uwire_write_reg(int idx, u16 val)
@@ -481,11 +481,6 @@ static int uwire_probe(struct platform_device *pdev)
}
clk_prepare_enable(uwire->ck);
- if (cpu_is_omap7xx())
- uwire_idx_shift = 1;
- else
- uwire_idx_shift = 2;
-
uwire_write_reg(UWIRE_SR3, 1);
/* the spi->mode bits understood by this driver: */
@@ -536,15 +531,6 @@ static struct platform_driver uwire_driver = {
static int __init omap_uwire_init(void)
{
- /* FIXME move these into the relevant board init code. also, include
- * H3 support; it uses tsc2101 like H2 (on a different chipselect).
- */
-
- if (machine_is_omap_h2()) {
- /* defaults: W21 SDO, U18 SDI, V19 SCL */
- omap_cfg_reg(N14_1610_UWIRE_CS0);
- omap_cfg_reg(N15_1610_UWIRE_CS1);
- }
return platform_driver_register(&uwire_driver);
}
diff --git a/drivers/usb/gadget/udc/omap_udc.c b/drivers/usb/gadget/udc/omap_udc.c
index bea346e362b2..1be8c19f2a04 100644
--- a/drivers/usb/gadget/udc/omap_udc.c
+++ b/drivers/usb/gadget/udc/omap_udc.c
@@ -2036,12 +2036,7 @@ static irqreturn_t omap_udc_iso_irq(int irq, void *_dev)
static inline int machine_without_vbus_sense(void)
{
- return machine_is_omap_innovator()
- || machine_is_omap_osk()
- || machine_is_omap_palmte()
- || machine_is_sx1()
- /* No known omap7xx boards with vbus sense */
- || cpu_is_omap7xx();
+ return machine_is_omap_osk() || machine_is_sx1();
}
static int omap_udc_start(struct usb_gadget *g,
@@ -2759,9 +2754,6 @@ static int omap_udc_probe(struct platform_device *pdev)
struct clk *dc_clk = NULL;
struct clk *hhc_clk = NULL;
- if (cpu_is_omap7xx())
- use_dma = 0;
-
/* NOTE: "knows" the order of the resources! */
if (!request_mem_region(pdev->resource[0].start,
resource_size(&pdev->resource[0]),
@@ -2780,16 +2772,6 @@ static int omap_udc_probe(struct platform_device *pdev)
udelay(100);
}
- if (cpu_is_omap7xx()) {
- dc_clk = clk_get(&pdev->dev, "usb_dc_ck");
- hhc_clk = clk_get(&pdev->dev, "l3_ocpi_ck");
- BUG_ON(IS_ERR(dc_clk) || IS_ERR(hhc_clk));
- /* can't use omap_udc_enable_clock yet */
- clk_prepare_enable(dc_clk);
- clk_prepare_enable(hhc_clk);
- udelay(100);
- }
-
INFO("OMAP UDC rev %d.%d%s\n",
omap_readw(UDC_REV) >> 4, omap_readw(UDC_REV) & 0xf,
config->otg ? ", Mini-AB" : "");
@@ -2914,7 +2896,7 @@ static int omap_udc_probe(struct platform_device *pdev)
goto cleanup1;
}
#endif
- if (cpu_is_omap16xx() || cpu_is_omap7xx()) {
+ if (cpu_is_omap16xx()) {
udc->dc_clk = dc_clk;
udc->hhc_clk = hhc_clk;
clk_disable(hhc_clk);
@@ -2933,7 +2915,7 @@ static int omap_udc_probe(struct platform_device *pdev)
if (!IS_ERR_OR_NULL(xceiv))
usb_put_phy(xceiv);
- if (cpu_is_omap16xx() || cpu_is_omap7xx()) {
+ if (cpu_is_omap16xx()) {
clk_disable_unprepare(hhc_clk);
clk_disable_unprepare(dc_clk);
clk_put(hhc_clk);
diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c
index cb29701df911..d7f594db56c6 100644
--- a/drivers/usb/host/ohci-omap.c
+++ b/drivers/usb/host/ohci-omap.c
@@ -107,10 +107,6 @@ static int ohci_omap_reset(struct usb_hcd *hcd)
hcd->power_budget = 8;
}
- /* boards can use OTG transceivers in non-OTG modes */
- need_transceiver = need_transceiver
- || machine_is_omap_h2() || machine_is_omap_h3();
-
/* XXX OMAP16xx only */
if (config->ocpi_enable)
config->ocpi_enable();
@@ -150,7 +146,7 @@ static int ohci_omap_reset(struct usb_hcd *hcd)
}
/* board-specific power switching and overcurrent support */
- if (machine_is_omap_osk() || machine_is_omap_innovator()) {
+ if (machine_is_omap_osk()) {
u32 rh = roothub_a (ohci);
/* power switching (ganged by default) */
diff --git a/drivers/usb/musb/musb_dma.h b/drivers/usb/musb/musb_dma.h
index 7d67b69df0a0..be32c6f90848 100644
--- a/drivers/usb/musb/musb_dma.h
+++ b/drivers/usb/musb/musb_dma.h
@@ -61,12 +61,6 @@ struct musb_hw_ep;
#define musb_dma_cppi41(musb) 0
#endif
-#ifdef CONFIG_USB_TI_CPPI_DMA
-#define musb_dma_cppi(musb) (musb->ops->quirks & MUSB_DMA_CPPI)
-#else
-#define musb_dma_cppi(musb) 0
-#endif
-
#ifdef CONFIG_USB_TUSB_OMAP_DMA
#define tusb_dma_omap(musb) (musb->ops->quirks & MUSB_DMA_TUSB_OMAP)
#else
@@ -79,9 +73,8 @@ struct musb_hw_ep;
#define musb_dma_inventra(musb) 0
#endif
-#if defined(CONFIG_USB_TI_CPPI_DMA) || defined(CONFIG_USB_TI_CPPI41_DMA)
-#define is_cppi_enabled(musb) \
- (musb_dma_cppi(musb) || musb_dma_cppi41(musb))
+#if defined(CONFIG_USB_TI_CPPI41_DMA)
+#define is_cppi_enabled(musb) musb_dma_cppi41(musb)
#else
#define is_cppi_enabled(musb) 0
#endif
diff --git a/drivers/usb/phy/phy-isp1301-omap.c b/drivers/usb/phy/phy-isp1301-omap.c
index e5d3f206097c..394386a4bef8 100644
--- a/drivers/usb/phy/phy-isp1301-omap.c
+++ b/drivers/usb/phy/phy-isp1301-omap.c
@@ -77,51 +77,6 @@ struct isp1301 {
/*-------------------------------------------------------------------------*/
-/* board-specific PM hooks */
-
-#if defined(CONFIG_MACH_OMAP_H2) || defined(CONFIG_MACH_OMAP_H3)
-
-#if IS_REACHABLE(CONFIG_TPS65010)
-
-#include <linux/mfd/tps65010.h>
-
-#else
-
-static inline int tps65010_set_vbus_draw(unsigned mA)
-{
- pr_debug("tps65010: draw %d mA (STUB)\n", mA);
- return 0;
-}
-
-#endif
-
-static void enable_vbus_draw(struct isp1301 *isp, unsigned mA)
-{
- int status = tps65010_set_vbus_draw(mA);
- if (status < 0)
- pr_debug(" VBUS %d mA error %d\n", mA, status);
-}
-
-#else
-
-static void enable_vbus_draw(struct isp1301 *isp, unsigned mA)
-{
- /* H4 controls this by DIP switch S2.4; no soft control.
- * ON means the charger is always enabled. Leave it OFF
- * unless the OTG port is used only in B-peripheral mode.
- */
-}
-
-#endif
-
-static void enable_vbus_source(struct isp1301 *isp)
-{
- /* this board won't supply more than 8mA vbus power.
- * some boards can switch a 100ma "unit load" (or more).
- */
-}
-
-
/* products will deliver OTG messages with LEDs, GUI, etc */
static inline void notresponding(struct isp1301 *isp)
{
@@ -916,10 +871,8 @@ static void b_peripheral(struct isp1301 *isp)
usb_gadget_vbus_connect(isp->phy.otg->gadget);
#ifdef CONFIG_USB_OTG
- enable_vbus_draw(isp, 8);
otg_update_isp(isp);
#else
- enable_vbus_draw(isp, 100);
/* UDC driver just set OTG_BSESSVLD */
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1, OTG1_DP_PULLUP);
isp1301_clear_bits(isp, ISP1301_OTG_CONTROL_1, OTG1_DP_PULLDOWN);
@@ -947,7 +900,6 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
a_idle(isp, "idle");
fallthrough;
case OTG_STATE_A_IDLE:
- enable_vbus_source(isp);
fallthrough;
case OTG_STATE_A_WAIT_VRISE:
/* we skip over OTG_STATE_A_WAIT_BCON, since
@@ -1023,7 +975,6 @@ static void isp_update_otg(struct isp1301 *isp, u8 stat)
case OTG_STATE_B_HOST:
if (likely(isp_bstat & OTG_B_SESS_VLD))
break;
- enable_vbus_draw(isp, 0);
#ifndef CONFIG_USB_OTG
/* UDC driver will clear OTG_BSESSVLD */
isp1301_set_bits(isp, ISP1301_OTG_CONTROL_1,
@@ -1283,9 +1234,6 @@ isp1301_set_host(struct usb_otg *otg, struct usb_bus *host)
power_up(isp);
- if (machine_is_omap_h2())
- isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
-
dev_info(&isp->client->dev, "A-Host sessions ok\n");
isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
INTR_ID_GND);
@@ -1320,8 +1268,6 @@ isp1301_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget)
if (!gadget) {
omap_writew(0, OTG_IRQ_EN);
- if (!otg->default_a)
- enable_vbus_draw(isp, 0);
usb_gadget_vbus_disconnect(otg->gadget);
otg->gadget = NULL;
power_down(isp);
@@ -1352,9 +1298,6 @@ isp1301_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget)
power_up(isp);
isp->phy.otg->state = OTG_STATE_B_IDLE;
- if (machine_is_omap_h2() || machine_is_omap_h3())
- isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1, MC1_DAT_SE0);
-
isp1301_set_bits(isp, ISP1301_INTERRUPT_RISING,
INTR_SESS_VLD);
isp1301_set_bits(isp, ISP1301_INTERRUPT_FALLING,
@@ -1380,16 +1323,6 @@ isp1301_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget)
/*-------------------------------------------------------------------------*/
-static int
-isp1301_set_power(struct usb_phy *dev, unsigned mA)
-{
- if (!the_transceiver)
- return -ENODEV;
- if (dev->otg->state == OTG_STATE_B_PERIPHERAL)
- enable_vbus_draw(the_transceiver, mA);
- return 0;
-}
-
static int
isp1301_start_srp(struct usb_otg *otg)
{
@@ -1538,26 +1471,7 @@ isp1301_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
}
#endif
- if (machine_is_omap_h2()) {
- struct gpio_desc *gpiod;
-
- /* full speed signaling by default */
- isp1301_set_bits(isp, ISP1301_MODE_CONTROL_1,
- MC1_SPEED);
- isp1301_set_bits(isp, ISP1301_MODE_CONTROL_2,
- MC2_SPD_SUSP_CTRL);
-
- gpiod = devm_gpiod_get(&i2c->dev, NULL, GPIOD_IN);
- if (IS_ERR(gpiod)) {
- dev_err(&i2c->dev, "cannot obtain H2 GPIO\n");
- goto fail;
- }
- gpiod_set_consumer_name(gpiod, "isp1301");
- irq = gpiod_to_irq(gpiod);
- isp->irq_type = IRQF_TRIGGER_FALLING;
- } else {
- irq = i2c->irq;
- }
+ irq = i2c->irq;
status = request_irq(irq, isp1301_irq,
isp->irq_type, DRIVER_NAME, isp);
@@ -1569,15 +1483,12 @@ isp1301_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
isp->phy.dev = &i2c->dev;
isp->phy.label = DRIVER_NAME;
- isp->phy.set_power = isp1301_set_power;
-
isp->phy.otg->usb_phy = &isp->phy;
isp->phy.otg->set_host = isp1301_set_host;
isp->phy.otg->set_peripheral = isp1301_set_peripheral;
isp->phy.otg->start_srp = isp1301_start_srp;
isp->phy.otg->start_hnp = isp1301_start_hnp;
- enable_vbus_draw(isp, 0);
power_down(isp);
the_transceiver = isp;
diff --git a/drivers/video/fbdev/omap/lcdc.c b/drivers/video/fbdev/omap/lcdc.c
index e7ce783e5215..abb8b11464e8 100644
--- a/drivers/video/fbdev/omap/lcdc.c
+++ b/drivers/video/fbdev/omap/lcdc.c
@@ -706,8 +706,6 @@ static int omap_lcdc_init(struct omapfb_device *fbdev, int ext_mode,
if (machine_is_ams_delta())
rate /= 4;
- if (machine_is_omap_h3())
- rate /= 3;
r = clk_set_rate(lcdc.lcd_ck, rate);
if (r) {
dev_err(fbdev->dev, "failed to adjust LCD rate\n");
diff --git a/include/linux/soc/ti/omap1-soc.h b/include/linux/soc/ti/omap1-soc.h
index 81008d400bb6..a42d9aa68648 100644
--- a/include/linux/soc/ti/omap1-soc.h
+++ b/include/linux/soc/ti/omap1-soc.h
@@ -20,22 +20,6 @@
#undef MULTI_OMAP1
#undef OMAP_NAME
-#ifdef CONFIG_ARCH_OMAP730
-# ifdef OMAP_NAME
-# undef MULTI_OMAP1
-# define MULTI_OMAP1
-# else
-# define OMAP_NAME omap730
-# endif
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-# ifdef OMAP_NAME
-# undef MULTI_OMAP1
-# define MULTI_OMAP1
-# else
-# define OMAP_NAME omap850
-# endif
-#endif
#ifdef CONFIG_ARCH_OMAP15XX
# ifdef OMAP_NAME
# undef MULTI_OMAP1
@@ -69,7 +53,6 @@ unsigned int omap_rev(void);
/*
* Macros to group OMAP into cpu classes.
* These can be used in most places.
- * cpu_is_omap7xx(): True for OMAP730, OMAP850
* cpu_is_omap15xx(): True for OMAP1510, OMAP5910 and OMAP310
* cpu_is_omap16xx(): True for OMAP1610, OMAP5912 and OMAP1710
*/
@@ -89,23 +72,13 @@ static inline int is_omap ##subclass (void) \
return (GET_OMAP_SUBCLASS == (id)) ? 1 : 0; \
}
-IS_OMAP_CLASS(7xx, 0x07)
IS_OMAP_CLASS(15xx, 0x15)
IS_OMAP_CLASS(16xx, 0x16)
-#define cpu_is_omap7xx() 0
#define cpu_is_omap15xx() 0
#define cpu_is_omap16xx() 0
#if defined(MULTI_OMAP1)
-# if defined(CONFIG_ARCH_OMAP730)
-# undef cpu_is_omap7xx
-# define cpu_is_omap7xx() is_omap7xx()
-# endif
-# if defined(CONFIG_ARCH_OMAP850)
-# undef cpu_is_omap7xx
-# define cpu_is_omap7xx() is_omap7xx()
-# endif
# if defined(CONFIG_ARCH_OMAP15XX)
# undef cpu_is_omap15xx
# define cpu_is_omap15xx() is_omap15xx()
@@ -115,14 +88,6 @@ IS_OMAP_CLASS(16xx, 0x16)
# define cpu_is_omap16xx() is_omap16xx()
# endif
#else
-# if defined(CONFIG_ARCH_OMAP730)
-# undef cpu_is_omap7xx
-# define cpu_is_omap7xx() 1
-# endif
-# if defined(CONFIG_ARCH_OMAP850)
-# undef cpu_is_omap7xx
-# define cpu_is_omap7xx() 1
-# endif
# if defined(CONFIG_ARCH_OMAP15XX)
# undef cpu_is_omap15xx
# define cpu_is_omap15xx() 1
--
2.29.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 15/17] fbdev: omapfb: remove unused board support
[not found] ` <20221019150410.3851944-1-arnd@kernel.org>
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
@ 2022-10-19 15:03 ` Arnd Bergmann
2022-10-24 5:50 ` Tony Lindgren
2022-10-19 15:03 ` [PATCH 16/17] spi: remove omap 100K driver Arnd Bergmann
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
3 siblings, 1 reply; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-19 15:03 UTC (permalink / raw)
To: linux-arm-kernel, Helge Deller
Cc: linux-kernel, Arnd Bergmann, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, linux-omap, Marek Vasut, Angelo Arrifano,
Imre Deak, Bartlomiej Zolnierkiewicz, linux-fbdev, dri-devel
From: Arnd Bergmann <arnd@arndb.de>
A number of omap1 based board files got removed, so the corresponding
framebuffer drivers are no longer used. The remaining ones are for
ams_delta, osk and palmTE, which are still part of the mainline kernel.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Angelo Arrifano <miknix@gmail.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
drivers/video/fbdev/omap/Kconfig | 9 ---
drivers/video/fbdev/omap/Makefile | 6 --
drivers/video/fbdev/omap/lcd_h3.c | 82 --------------------
drivers/video/fbdev/omap/lcd_htcherald.c | 59 --------------
drivers/video/fbdev/omap/lcd_inn1510.c | 69 -----------------
drivers/video/fbdev/omap/lcd_inn1610.c | 99 ------------------------
drivers/video/fbdev/omap/lcd_palmtt.c | 65 ----------------
drivers/video/fbdev/omap/lcd_palmz71.c | 59 --------------
8 files changed, 448 deletions(-)
delete mode 100644 drivers/video/fbdev/omap/lcd_h3.c
delete mode 100644 drivers/video/fbdev/omap/lcd_htcherald.c
delete mode 100644 drivers/video/fbdev/omap/lcd_inn1510.c
delete mode 100644 drivers/video/fbdev/omap/lcd_inn1610.c
delete mode 100644 drivers/video/fbdev/omap/lcd_palmtt.c
delete mode 100644 drivers/video/fbdev/omap/lcd_palmz71.c
diff --git a/drivers/video/fbdev/omap/Kconfig b/drivers/video/fbdev/omap/Kconfig
index b1786cf1b486..a6548283451f 100644
--- a/drivers/video/fbdev/omap/Kconfig
+++ b/drivers/video/fbdev/omap/Kconfig
@@ -40,15 +40,6 @@ config FB_OMAP_LCD_MIPID
the Mobile Industry Processor Interface DBI-C/DCS
specification. (Supported LCDs: Philips LPH8923, Sharp LS041Y3)
-config FB_OMAP_LCD_H3
- bool "TPS65010 LCD controller on OMAP-H3"
- depends on MACH_OMAP_H3 || COMPILE_TEST
- depends on TPS65010=y
- default y
- help
- Say Y here if you want to have support for the LCD on the
- H3 board.
-
config FB_OMAP_DMA_TUNE
bool "Set DMA SDRAM access priority high"
depends on FB_OMAP
diff --git a/drivers/video/fbdev/omap/Makefile b/drivers/video/fbdev/omap/Makefile
index b88e02f5cb1f..504edb9c09dd 100644
--- a/drivers/video/fbdev/omap/Makefile
+++ b/drivers/video/fbdev/omap/Makefile
@@ -17,16 +17,10 @@ objs-y$(CONFIG_FB_OMAP_LCDC_EXTERNAL) += sossi.o
objs-y$(CONFIG_FB_OMAP_LCDC_HWA742) += hwa742.o
lcds-y$(CONFIG_MACH_AMS_DELTA) += lcd_ams_delta.o
-lcds-y$(CONFIG_FB_OMAP_LCD_H3) += lcd_h3.o
lcds-y$(CONFIG_MACH_OMAP_PALMTE) += lcd_palmte.o
-lcds-y$(CONFIG_MACH_OMAP_PALMTT) += lcd_palmtt.o
-lcds-y$(CONFIG_MACH_OMAP_PALMZ71) += lcd_palmz71.o
-lcds-$(CONFIG_ARCH_OMAP16XX)$(CONFIG_MACH_OMAP_INNOVATOR) += lcd_inn1610.o
-lcds-$(CONFIG_ARCH_OMAP15XX)$(CONFIG_MACH_OMAP_INNOVATOR) += lcd_inn1510.o
lcds-y$(CONFIG_MACH_OMAP_OSK) += lcd_osk.o
lcds-y$(CONFIG_FB_OMAP_LCD_MIPID) += lcd_mipid.o
-lcds-y$(CONFIG_MACH_HERALD) += lcd_htcherald.o
omapfb-objs := $(objs-yy)
diff --git a/drivers/video/fbdev/omap/lcd_h3.c b/drivers/video/fbdev/omap/lcd_h3.c
deleted file mode 100644
index 1766dff767bb..000000000000
--- a/drivers/video/fbdev/omap/lcd_h3.c
+++ /dev/null
@@ -1,82 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LCD panel support for the TI OMAP H3 board
- *
- * Copyright (C) 2004 Nokia Corporation
- * Author: Imre Deak <imre.deak@nokia.com>
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/tps65010.h>
-#include <linux/gpio.h>
-
-#include "omapfb.h"
-
-#define MODULE_NAME "omapfb-lcd_h3"
-
-static int h3_panel_enable(struct lcd_panel *panel)
-{
- int r = 0;
-
- /* GPIO1 and GPIO2 of TPS65010 send LCD_ENBKL and LCD_ENVDD signals */
- r = tps65010_set_gpio_out_value(GPIO1, HIGH);
- if (!r)
- r = tps65010_set_gpio_out_value(GPIO2, HIGH);
- if (r)
- pr_err(MODULE_NAME ": Unable to turn on LCD panel\n");
-
- return r;
-}
-
-static void h3_panel_disable(struct lcd_panel *panel)
-{
- int r = 0;
-
- /* GPIO1 and GPIO2 of TPS65010 send LCD_ENBKL and LCD_ENVDD signals */
- r = tps65010_set_gpio_out_value(GPIO1, LOW);
- if (!r)
- tps65010_set_gpio_out_value(GPIO2, LOW);
- if (r)
- pr_err(MODULE_NAME ": Unable to turn off LCD panel\n");
-}
-
-static struct lcd_panel h3_panel = {
- .name = "h3",
- .config = OMAP_LCDC_PANEL_TFT,
-
- .data_lines = 16,
- .bpp = 16,
- .x_res = 240,
- .y_res = 320,
- .pixel_clock = 12000,
- .hsw = 12,
- .hfp = 14,
- .hbp = 72 - 12,
- .vsw = 1,
- .vfp = 1,
- .vbp = 0,
- .pcd = 0,
-
- .enable = h3_panel_enable,
- .disable = h3_panel_disable,
-};
-
-static int h3_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&h3_panel);
- return 0;
-}
-
-static struct platform_driver h3_panel_driver = {
- .probe = h3_panel_probe,
- .driver = {
- .name = "lcd_h3",
- },
-};
-
-module_platform_driver(h3_panel_driver);
-
-MODULE_AUTHOR("Imre Deak");
-MODULE_DESCRIPTION("LCD panel support for the TI OMAP H3 board");
-MODULE_LICENSE("GPL");
diff --git a/drivers/video/fbdev/omap/lcd_htcherald.c b/drivers/video/fbdev/omap/lcd_htcherald.c
deleted file mode 100644
index d1c615c516dd..000000000000
--- a/drivers/video/fbdev/omap/lcd_htcherald.c
+++ /dev/null
@@ -1,59 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * File: drivers/video/omap/lcd-htcherald.c
- *
- * LCD panel support for the HTC Herald
- *
- * Copyright (C) 2009 Cory Maccarrone <darkstar6262@gmail.com>
- * Copyright (C) 2009 Wing Linux
- *
- * Based on the lcd_htcwizard.c file from the linwizard project:
- * Copyright (C) linwizard.sourceforge.net
- * Author: Angelo Arrifano <miknix@gmail.com>
- * Based on lcd_h4 by Imre Deak <imre.deak@nokia.com>
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include "omapfb.h"
-
-/* Found on WIZ200 (miknix) and some HERA110 models (darkstar62) */
-static struct lcd_panel htcherald_panel_1 = {
- .name = "lcd_herald",
- .config = OMAP_LCDC_PANEL_TFT |
- OMAP_LCDC_INV_HSYNC |
- OMAP_LCDC_INV_VSYNC |
- OMAP_LCDC_INV_PIX_CLOCK,
- .bpp = 16,
- .data_lines = 16,
- .x_res = 240,
- .y_res = 320,
- .pixel_clock = 6093,
- .pcd = 0, /* 15 */
- .hsw = 10,
- .hfp = 10,
- .hbp = 20,
- .vsw = 3,
- .vfp = 2,
- .vbp = 2,
-};
-
-static int htcherald_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&htcherald_panel_1);
- return 0;
-}
-
-static struct platform_driver htcherald_panel_driver = {
- .probe = htcherald_panel_probe,
- .driver = {
- .name = "lcd_htcherald",
- },
-};
-
-module_platform_driver(htcherald_panel_driver);
-
-MODULE_AUTHOR("Cory Maccarrone");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("LCD panel support for the HTC Herald");
diff --git a/drivers/video/fbdev/omap/lcd_inn1510.c b/drivers/video/fbdev/omap/lcd_inn1510.c
deleted file mode 100644
index bb915637e9b6..000000000000
--- a/drivers/video/fbdev/omap/lcd_inn1510.c
+++ /dev/null
@@ -1,69 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LCD panel support for the TI OMAP1510 Innovator board
- *
- * Copyright (C) 2004 Nokia Corporation
- * Author: Imre Deak <imre.deak@nokia.com>
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/soc/ti/omap1-soc.h>
-
-#include "omapfb.h"
-
-static void __iomem *omap1510_fpga_lcd_panel_control;
-
-static int innovator1510_panel_enable(struct lcd_panel *panel)
-{
- __raw_writeb(0x7, omap1510_fpga_lcd_panel_control);
- return 0;
-}
-
-static void innovator1510_panel_disable(struct lcd_panel *panel)
-{
- __raw_writeb(0x0, omap1510_fpga_lcd_panel_control);
-}
-
-static struct lcd_panel innovator1510_panel = {
- .name = "inn1510",
- .config = OMAP_LCDC_PANEL_TFT,
-
- .bpp = 16,
- .data_lines = 16,
- .x_res = 240,
- .y_res = 320,
- .pixel_clock = 12500,
- .hsw = 40,
- .hfp = 40,
- .hbp = 72,
- .vsw = 1,
- .vfp = 1,
- .vbp = 0,
- .pcd = 12,
-
- .enable = innovator1510_panel_enable,
- .disable = innovator1510_panel_disable,
-};
-
-static int innovator1510_panel_probe(struct platform_device *pdev)
-{
- omap1510_fpga_lcd_panel_control = (void __iomem *)pdev->dev.platform_data;
- omapfb_register_panel(&innovator1510_panel);
- return 0;
-}
-
-static struct platform_driver innovator1510_panel_driver = {
- .probe = innovator1510_panel_probe,
- .driver = {
- .name = "lcd_inn1510",
- },
-};
-
-module_platform_driver(innovator1510_panel_driver);
-
-MODULE_AUTHOR("Imre Deak");
-MODULE_DESCRIPTION("LCD panel support for the TI OMAP1510 Innovator board");
-MODULE_LICENSE("GPL");
diff --git a/drivers/video/fbdev/omap/lcd_inn1610.c b/drivers/video/fbdev/omap/lcd_inn1610.c
deleted file mode 100644
index 901b28f35fab..000000000000
--- a/drivers/video/fbdev/omap/lcd_inn1610.c
+++ /dev/null
@@ -1,99 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LCD panel support for the TI OMAP1610 Innovator board
- *
- * Copyright (C) 2004 Nokia Corporation
- * Author: Imre Deak <imre.deak@nokia.com>
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-
-#include <linux/gpio.h>
-#include "omapfb.h"
-
-#define MODULE_NAME "omapfb-lcd_h3"
-
-static int innovator1610_panel_init(struct lcd_panel *panel,
- struct omapfb_device *fbdev)
-{
- int r = 0;
-
- /* configure GPIO(14, 15) as outputs */
- if (gpio_request_one(14, GPIOF_OUT_INIT_LOW, "lcd_en0")) {
- pr_err(MODULE_NAME ": can't request GPIO 14\n");
- r = -1;
- goto exit;
- }
- if (gpio_request_one(15, GPIOF_OUT_INIT_LOW, "lcd_en1")) {
- pr_err(MODULE_NAME ": can't request GPIO 15\n");
- gpio_free(14);
- r = -1;
- goto exit;
- }
-exit:
- return r;
-}
-
-static void innovator1610_panel_cleanup(struct lcd_panel *panel)
-{
- gpio_free(15);
- gpio_free(14);
-}
-
-static int innovator1610_panel_enable(struct lcd_panel *panel)
-{
- /* set GPIO14 and GPIO15 high */
- gpio_set_value(14, 1);
- gpio_set_value(15, 1);
- return 0;
-}
-
-static void innovator1610_panel_disable(struct lcd_panel *panel)
-{
- /* set GPIO13, GPIO14 and GPIO15 low */
- gpio_set_value(14, 0);
- gpio_set_value(15, 0);
-}
-
-static struct lcd_panel innovator1610_panel = {
- .name = "inn1610",
- .config = OMAP_LCDC_PANEL_TFT,
-
- .bpp = 16,
- .data_lines = 16,
- .x_res = 320,
- .y_res = 240,
- .pixel_clock = 12500,
- .hsw = 40,
- .hfp = 40,
- .hbp = 72,
- .vsw = 1,
- .vfp = 1,
- .vbp = 0,
- .pcd = 12,
-
- .init = innovator1610_panel_init,
- .cleanup = innovator1610_panel_cleanup,
- .enable = innovator1610_panel_enable,
- .disable = innovator1610_panel_disable,
-};
-
-static int innovator1610_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&innovator1610_panel);
- return 0;
-}
-
-static struct platform_driver innovator1610_panel_driver = {
- .probe = innovator1610_panel_probe,
- .driver = {
- .name = "lcd_inn1610",
- },
-};
-
-module_platform_driver(innovator1610_panel_driver);
-
-MODULE_AUTHOR("Imre Deak");
-MODULE_DESCRIPTION("LCD panel support for the TI OMAP1610 Innovator board");
-MODULE_LICENSE("GPL");
diff --git a/drivers/video/fbdev/omap/lcd_palmtt.c b/drivers/video/fbdev/omap/lcd_palmtt.c
deleted file mode 100644
index 703af0bc5c92..000000000000
--- a/drivers/video/fbdev/omap/lcd_palmtt.c
+++ /dev/null
@@ -1,65 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LCD panel support for Palm Tungsten|T
- * Current version : Marek Vasut <marek.vasut@gmail.com>
- *
- * Modified from lcd_inn1510.c
- */
-
-/*
-GPIO11 - backlight
-GPIO12 - screen blanking
-GPIO13 - screen blanking
-*/
-
-#include <linux/platform_device.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include "omapfb.h"
-
-static unsigned long palmtt_panel_get_caps(struct lcd_panel *panel)
-{
- return OMAPFB_CAPS_SET_BACKLIGHT;
-}
-
-static struct lcd_panel palmtt_panel = {
- .name = "palmtt",
- .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
- OMAP_LCDC_INV_HSYNC | OMAP_LCDC_HSVS_RISING_EDGE |
- OMAP_LCDC_HSVS_OPPOSITE,
- .bpp = 16,
- .data_lines = 16,
- .x_res = 320,
- .y_res = 320,
- .pixel_clock = 10000,
- .hsw = 4,
- .hfp = 8,
- .hbp = 28,
- .vsw = 1,
- .vfp = 8,
- .vbp = 7,
- .pcd = 0,
-
- .get_caps = palmtt_panel_get_caps,
-};
-
-static int palmtt_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&palmtt_panel);
- return 0;
-}
-
-static struct platform_driver palmtt_panel_driver = {
- .probe = palmtt_panel_probe,
- .driver = {
- .name = "lcd_palmtt",
- },
-};
-
-module_platform_driver(palmtt_panel_driver);
-
-MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
-MODULE_DESCRIPTION("LCD panel support for Palm Tungsten|T");
-MODULE_LICENSE("GPL");
diff --git a/drivers/video/fbdev/omap/lcd_palmz71.c b/drivers/video/fbdev/omap/lcd_palmz71.c
deleted file mode 100644
index a955c908ab14..000000000000
--- a/drivers/video/fbdev/omap/lcd_palmz71.c
+++ /dev/null
@@ -1,59 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * LCD panel support for the Palm Zire71
- *
- * Original version : Romain Goyet
- * Current version : Laurent Gonzalez
- * Modified for zire71 : Marek Vasut
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include "omapfb.h"
-
-static unsigned long palmz71_panel_get_caps(struct lcd_panel *panel)
-{
- return OMAPFB_CAPS_SET_BACKLIGHT;
-}
-
-static struct lcd_panel palmz71_panel = {
- .name = "palmz71",
- .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
- OMAP_LCDC_INV_HSYNC | OMAP_LCDC_HSVS_RISING_EDGE |
- OMAP_LCDC_HSVS_OPPOSITE,
- .data_lines = 16,
- .bpp = 16,
- .pixel_clock = 24000,
- .x_res = 320,
- .y_res = 320,
- .hsw = 4,
- .hfp = 8,
- .hbp = 28,
- .vsw = 1,
- .vfp = 8,
- .vbp = 7,
- .pcd = 0,
-
- .get_caps = palmz71_panel_get_caps,
-};
-
-static int palmz71_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&palmz71_panel);
- return 0;
-}
-
-static struct platform_driver palmz71_panel_driver = {
- .probe = palmz71_panel_probe,
- .driver = {
- .name = "lcd_palmz71",
- },
-};
-
-module_platform_driver(palmz71_panel_driver);
-
-MODULE_AUTHOR("Romain Goyet, Laurent Gonzalez, Marek Vasut");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("LCD panel support for the Palm Zire71");
--
2.29.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH 16/17] spi: remove omap 100K driver
[not found] ` <20221019150410.3851944-1-arnd@kernel.org>
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
2022-10-19 15:03 ` [PATCH 15/17] fbdev: omapfb: remove unused board support Arnd Bergmann
@ 2022-10-19 15:03 ` Arnd Bergmann
2022-10-19 15:29 ` Mark Brown
2022-10-24 5:50 ` Tony Lindgren
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
3 siblings, 2 replies; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-19 15:03 UTC (permalink / raw)
To: linux-arm-kernel, Mark Brown
Cc: linux-kernel, Arnd Bergmann, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, linux-omap, Cory Maccarrone, Fabrice Crohas,
linux-spi
From: Arnd Bergmann <arnd@arndb.de>
The OMAP7xx/OMAP8xx support was removed since all of its boards
have no remaining users. Remove its spi driver as well.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Fabrice Crohas <fcrohas@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
drivers/spi/Kconfig | 6 -
drivers/spi/Makefile | 1 -
drivers/spi/spi-omap-100k.c | 490 ------------------------------------
3 files changed, 497 deletions(-)
delete mode 100644 drivers/spi/spi-omap-100k.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index d1bb62f7368b..bf0dc704abbe 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -697,12 +697,6 @@ config SPI_TI_QSPI
This device supports single, dual and quad read support, while
it only supports single write mode.
-config SPI_OMAP_100K
- tristate "OMAP SPI 100K"
- depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
- help
- OMAP SPI 100K master controller for omap7xx boards.
-
config SPI_ORION
tristate "Orion SPI master"
depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 4b34e855c841..ae5ba0109d4b 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -90,7 +90,6 @@ obj-$(CONFIG_SPI_OC_TINY) += spi-oc-tiny.o
spi-octeon-objs := spi-cavium.o spi-cavium-octeon.o
obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o
obj-$(CONFIG_SPI_OMAP_UWIRE) += spi-omap-uwire.o
-obj-$(CONFIG_SPI_OMAP_100K) += spi-omap-100k.o
obj-$(CONFIG_SPI_OMAP24XX) += spi-omap2-mcspi.o
obj-$(CONFIG_SPI_TI_QSPI) += spi-ti-qspi.o
obj-$(CONFIG_SPI_ORION) += spi-orion.o
diff --git a/drivers/spi/spi-omap-100k.c b/drivers/spi/spi-omap-100k.c
deleted file mode 100644
index 061f7394e5b9..000000000000
--- a/drivers/spi/spi-omap-100k.c
+++ /dev/null
@@ -1,490 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * OMAP7xx SPI 100k controller driver
- * Author: Fabrice Crohas <fcrohas@gmail.com>
- * from original omap1_mcspi driver
- *
- * Copyright (C) 2005, 2006 Nokia Corporation
- * Author: Samuel Ortiz <samuel.ortiz@nokia.com> and
- * Juha Yrjola <juha.yrjola@nokia.com>
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/device.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/pm_runtime.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-
-#include <linux/spi/spi.h>
-
-#define OMAP1_SPI100K_MAX_FREQ 48000000
-
-#define ICR_SPITAS (OMAP7XX_ICR_BASE + 0x12)
-
-#define SPI_SETUP1 0x00
-#define SPI_SETUP2 0x02
-#define SPI_CTRL 0x04
-#define SPI_STATUS 0x06
-#define SPI_TX_LSB 0x08
-#define SPI_TX_MSB 0x0a
-#define SPI_RX_LSB 0x0c
-#define SPI_RX_MSB 0x0e
-
-#define SPI_SETUP1_INT_READ_ENABLE (1UL << 5)
-#define SPI_SETUP1_INT_WRITE_ENABLE (1UL << 4)
-#define SPI_SETUP1_CLOCK_DIVISOR(x) ((x) << 1)
-#define SPI_SETUP1_CLOCK_ENABLE (1UL << 0)
-
-#define SPI_SETUP2_ACTIVE_EDGE_FALLING (0UL << 0)
-#define SPI_SETUP2_ACTIVE_EDGE_RISING (1UL << 0)
-#define SPI_SETUP2_NEGATIVE_LEVEL (0UL << 5)
-#define SPI_SETUP2_POSITIVE_LEVEL (1UL << 5)
-#define SPI_SETUP2_LEVEL_TRIGGER (0UL << 10)
-#define SPI_SETUP2_EDGE_TRIGGER (1UL << 10)
-
-#define SPI_CTRL_SEN(x) ((x) << 7)
-#define SPI_CTRL_WORD_SIZE(x) (((x) - 1) << 2)
-#define SPI_CTRL_WR (1UL << 1)
-#define SPI_CTRL_RD (1UL << 0)
-
-#define SPI_STATUS_WE (1UL << 1)
-#define SPI_STATUS_RD (1UL << 0)
-
-/* use PIO for small transfers, avoiding DMA setup/teardown overhead and
- * cache operations; better heuristics consider wordsize and bitrate.
- */
-#define DMA_MIN_BYTES 8
-
-#define SPI_RUNNING 0
-#define SPI_SHUTDOWN 1
-
-struct omap1_spi100k {
- struct clk *ick;
- struct clk *fck;
-
- /* Virtual base address of the controller */
- void __iomem *base;
-};
-
-struct omap1_spi100k_cs {
- void __iomem *base;
- int word_len;
-};
-
-static void spi100k_enable_clock(struct spi_master *master)
-{
- unsigned int val;
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- /* enable SPI */
- val = readw(spi100k->base + SPI_SETUP1);
- val |= SPI_SETUP1_CLOCK_ENABLE;
- writew(val, spi100k->base + SPI_SETUP1);
-}
-
-static void spi100k_disable_clock(struct spi_master *master)
-{
- unsigned int val;
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- /* disable SPI */
- val = readw(spi100k->base + SPI_SETUP1);
- val &= ~SPI_SETUP1_CLOCK_ENABLE;
- writew(val, spi100k->base + SPI_SETUP1);
-}
-
-static void spi100k_write_data(struct spi_master *master, int len, int data)
-{
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- /* write 16-bit word, shifting 8-bit data if necessary */
- if (len <= 8) {
- data <<= 8;
- len = 16;
- }
-
- spi100k_enable_clock(master);
- writew(data, spi100k->base + SPI_TX_MSB);
-
- writew(SPI_CTRL_SEN(0) |
- SPI_CTRL_WORD_SIZE(len) |
- SPI_CTRL_WR,
- spi100k->base + SPI_CTRL);
-
- /* Wait for bit ack send change */
- while ((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_WE) != SPI_STATUS_WE)
- ;
- udelay(1000);
-
- spi100k_disable_clock(master);
-}
-
-static int spi100k_read_data(struct spi_master *master, int len)
-{
- int dataL;
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- /* Always do at least 16 bits */
- if (len <= 8)
- len = 16;
-
- spi100k_enable_clock(master);
- writew(SPI_CTRL_SEN(0) |
- SPI_CTRL_WORD_SIZE(len) |
- SPI_CTRL_RD,
- spi100k->base + SPI_CTRL);
-
- while ((readw(spi100k->base + SPI_STATUS) & SPI_STATUS_RD) != SPI_STATUS_RD)
- ;
- udelay(1000);
-
- dataL = readw(spi100k->base + SPI_RX_LSB);
- readw(spi100k->base + SPI_RX_MSB);
- spi100k_disable_clock(master);
-
- return dataL;
-}
-
-static void spi100k_open(struct spi_master *master)
-{
- /* get control of SPI */
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- writew(SPI_SETUP1_INT_READ_ENABLE |
- SPI_SETUP1_INT_WRITE_ENABLE |
- SPI_SETUP1_CLOCK_DIVISOR(0), spi100k->base + SPI_SETUP1);
-
- /* configure clock and interrupts */
- writew(SPI_SETUP2_ACTIVE_EDGE_FALLING |
- SPI_SETUP2_NEGATIVE_LEVEL |
- SPI_SETUP2_LEVEL_TRIGGER, spi100k->base + SPI_SETUP2);
-}
-
-static void omap1_spi100k_force_cs(struct omap1_spi100k *spi100k, int enable)
-{
- if (enable)
- writew(0x05fc, spi100k->base + SPI_CTRL);
- else
- writew(0x05fd, spi100k->base + SPI_CTRL);
-}
-
-static unsigned
-omap1_spi100k_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
-{
- struct omap1_spi100k_cs *cs = spi->controller_state;
- unsigned int count, c;
- int word_len;
-
- count = xfer->len;
- c = count;
- word_len = cs->word_len;
-
- if (word_len <= 8) {
- u8 *rx;
- const u8 *tx;
-
- rx = xfer->rx_buf;
- tx = xfer->tx_buf;
- do {
- c -= 1;
- if (xfer->tx_buf != NULL)
- spi100k_write_data(spi->master, word_len, *tx++);
- if (xfer->rx_buf != NULL)
- *rx++ = spi100k_read_data(spi->master, word_len);
- } while (c);
- } else if (word_len <= 16) {
- u16 *rx;
- const u16 *tx;
-
- rx = xfer->rx_buf;
- tx = xfer->tx_buf;
- do {
- c -= 2;
- if (xfer->tx_buf != NULL)
- spi100k_write_data(spi->master, word_len, *tx++);
- if (xfer->rx_buf != NULL)
- *rx++ = spi100k_read_data(spi->master, word_len);
- } while (c);
- } else if (word_len <= 32) {
- u32 *rx;
- const u32 *tx;
-
- rx = xfer->rx_buf;
- tx = xfer->tx_buf;
- do {
- c -= 4;
- if (xfer->tx_buf != NULL)
- spi100k_write_data(spi->master, word_len, *tx);
- if (xfer->rx_buf != NULL)
- *rx = spi100k_read_data(spi->master, word_len);
- } while (c);
- }
- return count - c;
-}
-
-/* called only when no transfer is active to this device */
-static int omap1_spi100k_setup_transfer(struct spi_device *spi,
- struct spi_transfer *t)
-{
- struct omap1_spi100k *spi100k = spi_master_get_devdata(spi->master);
- struct omap1_spi100k_cs *cs = spi->controller_state;
- u8 word_len;
-
- if (t != NULL)
- word_len = t->bits_per_word;
- else
- word_len = spi->bits_per_word;
-
- if (word_len > 32)
- return -EINVAL;
- cs->word_len = word_len;
-
- /* SPI init before transfer */
- writew(0x3e, spi100k->base + SPI_SETUP1);
- writew(0x00, spi100k->base + SPI_STATUS);
- writew(0x3e, spi100k->base + SPI_CTRL);
-
- return 0;
-}
-
-/* the spi->mode bits understood by this driver: */
-#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH)
-
-static int omap1_spi100k_setup(struct spi_device *spi)
-{
- int ret;
- struct omap1_spi100k *spi100k;
- struct omap1_spi100k_cs *cs = spi->controller_state;
-
- spi100k = spi_master_get_devdata(spi->master);
-
- if (!cs) {
- cs = devm_kzalloc(&spi->dev, sizeof(*cs), GFP_KERNEL);
- if (!cs)
- return -ENOMEM;
- cs->base = spi100k->base + spi->chip_select * 0x14;
- spi->controller_state = cs;
- }
-
- spi100k_open(spi->master);
-
- clk_prepare_enable(spi100k->ick);
- clk_prepare_enable(spi100k->fck);
-
- ret = omap1_spi100k_setup_transfer(spi, NULL);
-
- clk_disable_unprepare(spi100k->ick);
- clk_disable_unprepare(spi100k->fck);
-
- return ret;
-}
-
-static int omap1_spi100k_transfer_one_message(struct spi_master *master,
- struct spi_message *m)
-{
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
- struct spi_device *spi = m->spi;
- struct spi_transfer *t = NULL;
- int cs_active = 0;
- int status = 0;
-
- list_for_each_entry(t, &m->transfers, transfer_list) {
- if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
- break;
- }
- status = omap1_spi100k_setup_transfer(spi, t);
- if (status < 0)
- break;
-
- if (!cs_active) {
- omap1_spi100k_force_cs(spi100k, 1);
- cs_active = 1;
- }
-
- if (t->len) {
- unsigned count;
-
- count = omap1_spi100k_txrx_pio(spi, t);
- m->actual_length += count;
-
- if (count != t->len) {
- break;
- }
- }
-
- spi_transfer_delay_exec(t);
-
- /* ignore the "leave it on after last xfer" hint */
-
- if (t->cs_change) {
- omap1_spi100k_force_cs(spi100k, 0);
- cs_active = 0;
- }
- }
-
- status = omap1_spi100k_setup_transfer(spi, NULL);
-
- if (cs_active)
- omap1_spi100k_force_cs(spi100k, 0);
-
- m->status = status;
-
- spi_finalize_current_message(master);
-
- return status;
-}
-
-static int omap1_spi100k_probe(struct platform_device *pdev)
-{
- struct spi_master *master;
- struct omap1_spi100k *spi100k;
- int status = 0;
-
- if (!pdev->id)
- return -EINVAL;
-
- master = spi_alloc_master(&pdev->dev, sizeof(*spi100k));
- if (master == NULL) {
- dev_dbg(&pdev->dev, "master allocation failed\n");
- return -ENOMEM;
- }
-
- if (pdev->id != -1)
- master->bus_num = pdev->id;
-
- master->setup = omap1_spi100k_setup;
- master->transfer_one_message = omap1_spi100k_transfer_one_message;
- master->num_chipselect = 2;
- master->mode_bits = MODEBITS;
- master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32);
- master->min_speed_hz = OMAP1_SPI100K_MAX_FREQ/(1<<16);
- master->max_speed_hz = OMAP1_SPI100K_MAX_FREQ;
- master->auto_runtime_pm = true;
-
- spi100k = spi_master_get_devdata(master);
-
- /*
- * The memory region base address is taken as the platform_data.
- * You should allocate this with ioremap() before initializing
- * the SPI.
- */
- spi100k->base = (void __iomem *)dev_get_platdata(&pdev->dev);
-
- spi100k->ick = devm_clk_get(&pdev->dev, "ick");
- if (IS_ERR(spi100k->ick)) {
- dev_dbg(&pdev->dev, "can't get spi100k_ick\n");
- status = PTR_ERR(spi100k->ick);
- goto err;
- }
-
- spi100k->fck = devm_clk_get(&pdev->dev, "fck");
- if (IS_ERR(spi100k->fck)) {
- dev_dbg(&pdev->dev, "can't get spi100k_fck\n");
- status = PTR_ERR(spi100k->fck);
- goto err;
- }
-
- status = clk_prepare_enable(spi100k->ick);
- if (status != 0) {
- dev_err(&pdev->dev, "failed to enable ick: %d\n", status);
- goto err;
- }
-
- status = clk_prepare_enable(spi100k->fck);
- if (status != 0) {
- dev_err(&pdev->dev, "failed to enable fck: %d\n", status);
- goto err_ick;
- }
-
- pm_runtime_enable(&pdev->dev);
- pm_runtime_set_active(&pdev->dev);
-
- status = devm_spi_register_master(&pdev->dev, master);
- if (status < 0)
- goto err_fck;
-
- return status;
-
-err_fck:
- pm_runtime_disable(&pdev->dev);
- clk_disable_unprepare(spi100k->fck);
-err_ick:
- clk_disable_unprepare(spi100k->ick);
-err:
- spi_master_put(master);
- return status;
-}
-
-static int omap1_spi100k_remove(struct platform_device *pdev)
-{
- struct spi_master *master = platform_get_drvdata(pdev);
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- pm_runtime_disable(&pdev->dev);
-
- clk_disable_unprepare(spi100k->fck);
- clk_disable_unprepare(spi100k->ick);
-
- return 0;
-}
-
-#ifdef CONFIG_PM
-static int omap1_spi100k_runtime_suspend(struct device *dev)
-{
- struct spi_master *master = dev_get_drvdata(dev);
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
-
- clk_disable_unprepare(spi100k->ick);
- clk_disable_unprepare(spi100k->fck);
-
- return 0;
-}
-
-static int omap1_spi100k_runtime_resume(struct device *dev)
-{
- struct spi_master *master = dev_get_drvdata(dev);
- struct omap1_spi100k *spi100k = spi_master_get_devdata(master);
- int ret;
-
- ret = clk_prepare_enable(spi100k->ick);
- if (ret != 0) {
- dev_err(dev, "Failed to enable ick: %d\n", ret);
- return ret;
- }
-
- ret = clk_prepare_enable(spi100k->fck);
- if (ret != 0) {
- dev_err(dev, "Failed to enable fck: %d\n", ret);
- clk_disable_unprepare(spi100k->ick);
- return ret;
- }
-
- return 0;
-}
-#endif
-
-static const struct dev_pm_ops omap1_spi100k_pm = {
- SET_RUNTIME_PM_OPS(omap1_spi100k_runtime_suspend,
- omap1_spi100k_runtime_resume, NULL)
-};
-
-static struct platform_driver omap1_spi100k_driver = {
- .driver = {
- .name = "omap1_spi100k",
- .pm = &omap1_spi100k_pm,
- },
- .probe = omap1_spi100k_probe,
- .remove = omap1_spi100k_remove,
-};
-
-module_platform_driver(omap1_spi100k_driver);
-
-MODULE_DESCRIPTION("OMAP7xx SPI 100k controller driver");
-MODULE_AUTHOR("Fabrice Crohas <fcrohas@gmail.com>");
-MODULE_LICENSE("GPL");
--
2.29.2
^ permalink raw reply related [flat|nested] 24+ messages in thread
* Re: [PATCH 16/17] spi: remove omap 100K driver
2022-10-19 15:03 ` [PATCH 16/17] spi: remove omap 100K driver Arnd Bergmann
@ 2022-10-19 15:29 ` Mark Brown
2022-10-24 5:50 ` Tony Lindgren
1 sibling, 0 replies; 24+ messages in thread
From: Mark Brown @ 2022-10-19 15:29 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, linux-kernel, Arnd Bergmann, Aaro Koskinen,
Janusz Krzysztofik, Tony Lindgren, linux-omap, Cory Maccarrone,
Fabrice Crohas, linux-spi
[-- Attachment #1: Type: text/plain, Size: 278 bytes --]
On Wed, Oct 19, 2022 at 05:03:38PM +0200, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> The OMAP7xx/OMAP8xx support was removed since all of its boards
> have no remaining users. Remove its spi driver as well.
Acked-by: Mark Brown <broonie@kernel.org>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
@ 2022-10-19 17:15 ` Aaro Koskinen
2022-10-20 7:11 ` Arnd Bergmann
2022-10-19 19:30 ` Wolfram Sang
` (3 subsequent siblings)
4 siblings, 1 reply; 24+ messages in thread
From: Aaro Koskinen @ 2022-10-19 17:15 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Janusz Krzysztofik, Tony Lindgren,
linux-kernel, Arnd Bergmann, linux-omap, Lee Jones, Ulf Hansson,
Felipe Balbi, Greg Kroah-Hartman, linux-i2c, linux-mmc,
linux-usb
Hi,
On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> All board support that was marked as 'unused' earlier can
> now be removed, leaving the five machines that that still
> had someone using them in 2022, or that are supported in
> qemu.
[...]
> config OMAP_OSK_MISTRAL
> bool "Mistral QVGA board Support"
> depends on MACH_OMAP_OSK
> - depends on UNUSED_BOARD_FILES
> help
> The OSK supports an optional add-on board with a Quarter-VGA
> touchscreen, PDA-ish buttons, a resume button, bicolor LED,
> and camera connector. Say Y here if you have this board.
Shouldn't this go away as well?
A.
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 14/17] ARM: omap1: remove dead code
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
@ 2022-10-19 17:34 ` Aaro Koskinen
2022-10-21 7:51 ` Arnd Bergmann
2022-10-22 10:24 ` Greg Kroah-Hartman
` (2 subsequent siblings)
3 siblings, 1 reply; 24+ messages in thread
From: Aaro Koskinen @ 2022-10-19 17:34 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Paul Walmsley, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Arnd Bergmann, linux-omap,
Kevin Hilman, Mark Brown, Felipe Balbi, Greg Kroah-Hartman,
Alan Stern, Bin Liu, Helge Deller, linux-usb, linux-spi,
linux-fbdev, dri-devel
Hi,
On Wed, Oct 19, 2022 at 05:03:36PM +0200, Arnd Bergmann wrote:
> drivers/usb/phy/phy-isp1301-omap.c | 91 +-----------------------------
This driver and config option ISP1301_OMAP can be deleted altogether as
there are no users after H2/H3 boards are gone.
A.
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
2022-10-19 17:15 ` [PATCH 13/17] ARM: omap1: remove unused board files Aaro Koskinen
@ 2022-10-19 19:30 ` Wolfram Sang
2022-10-21 9:50 ` Lee Jones
` (2 subsequent siblings)
4 siblings, 0 replies; 24+ messages in thread
From: Wolfram Sang @ 2022-10-19 19:30 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Arnd Bergmann, linux-omap,
Lee Jones, Ulf Hansson, Felipe Balbi, Greg Kroah-Hartman,
linux-i2c, linux-mmc, linux-usb
[-- Attachment #1: Type: text/plain, Size: 561 bytes --]
On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> All board support that was marked as 'unused' earlier can
> now be removed, leaving the five machines that that still
> had someone using them in 2022, or that are supported in
> qemu.
>
> Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: linux-omap@vger.kernel.org
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@kernel.org>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-19 17:15 ` [PATCH 13/17] ARM: omap1: remove unused board files Aaro Koskinen
@ 2022-10-20 7:11 ` Arnd Bergmann
2022-10-20 19:35 ` Aaro Koskinen
0 siblings, 1 reply; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-20 7:11 UTC (permalink / raw)
To: Aaro Koskinen, Arnd Bergmann
Cc: linux-arm-kernel, Janusz Krzysztofik, Tony Lindgren,
linux-kernel, Linux-OMAP, Lee Jones, Ulf Hansson, Felipe Balbi,
Greg Kroah-Hartman, linux-i2c, linux-mmc @ vger . kernel . org,
linux-usb
On Wed, Oct 19, 2022, at 19:15, Aaro Koskinen wrote:
> Hi,
>
> On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
>> From: Arnd Bergmann <arnd@arndb.de>
>>
>> All board support that was marked as 'unused' earlier can
>> now be removed, leaving the five machines that that still
>> had someone using them in 2022, or that are supported in
>> qemu.
> [...]
>> config OMAP_OSK_MISTRAL
>> bool "Mistral QVGA board Support"
>> depends on MACH_OMAP_OSK
>> - depends on UNUSED_BOARD_FILES
>> help
>> The OSK supports an optional add-on board with a Quarter-VGA
>> touchscreen, PDA-ish buttons, a resume button, bicolor LED,
>> and camera connector. Say Y here if you have this board.
>
> Shouldn't this go away as well?
No, this one was incorrectly annotated, it's not actually
a board but it's an option for the OSK board that is not
getting removed. I considered making a separate patch
for removing the dependency, but that didn't seem worth it.
Arnd
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-20 7:11 ` Arnd Bergmann
@ 2022-10-20 19:35 ` Aaro Koskinen
2022-10-21 6:52 ` Arnd Bergmann
0 siblings, 1 reply; 24+ messages in thread
From: Aaro Koskinen @ 2022-10-20 19:35 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Arnd Bergmann, linux-arm-kernel, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Linux-OMAP, Lee Jones, Ulf Hansson,
Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc @ vger . kernel . org, linux-usb
Hi,
On Thu, Oct 20, 2022 at 09:11:11AM +0200, Arnd Bergmann wrote:
> On Wed, Oct 19, 2022, at 19:15, Aaro Koskinen wrote:
> > On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
> >> All board support that was marked as 'unused' earlier can
> >> now be removed, leaving the five machines that that still
> >> had someone using them in 2022, or that are supported in
> >> qemu.
> > [...]
> >> config OMAP_OSK_MISTRAL
> >> bool "Mistral QVGA board Support"
> >> depends on MACH_OMAP_OSK
> >> - depends on UNUSED_BOARD_FILES
> >> help
> >> The OSK supports an optional add-on board with a Quarter-VGA
> >> touchscreen, PDA-ish buttons, a resume button, bicolor LED,
> >> and camera connector. Say Y here if you have this board.
> >
> > Shouldn't this go away as well?
>
> No, this one was incorrectly annotated, it's not actually
> a board but it's an option for the OSK board that is not
> getting removed. I considered making a separate patch
> for removing the dependency, but that didn't seem worth it.
OK. For the record, I don't think anyone has this add-on board anymore,
and it has probably never been tested with the mainline kernel, so
it's likely in the "dead code" category... Maybe it could be changed to
"BROKEN", then the related OSK LCD panel stuff could be deleted later
on too.
A.
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-20 19:35 ` Aaro Koskinen
@ 2022-10-21 6:52 ` Arnd Bergmann
2022-10-21 11:11 ` Aaro Koskinen
0 siblings, 1 reply; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-21 6:52 UTC (permalink / raw)
To: Aaro Koskinen
Cc: Arnd Bergmann, linux-arm-kernel, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Linux-OMAP, Lee Jones, Ulf Hansson,
Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc @ vger . kernel . org, linux-usb
On Thu, Oct 20, 2022, at 21:35, Aaro Koskinen wrote:
> On Thu, Oct 20, 2022 at 09:11:11AM +0200, Arnd Bergmann wrote:
>> On Wed, Oct 19, 2022, at 19:15, Aaro Koskinen wrote:
>> > On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
>> >> All board support that was marked as 'unused' earlier can
>> >> now be removed, leaving the five machines that that still
>> >> had someone using them in 2022, or that are supported in
>> >> qemu.
>> > [...]
>> >> config OMAP_OSK_MISTRAL
>> >> bool "Mistral QVGA board Support"
>> >> depends on MACH_OMAP_OSK
>> >> - depends on UNUSED_BOARD_FILES
>> >> help
>> >> The OSK supports an optional add-on board with a Quarter-VGA
>> >> touchscreen, PDA-ish buttons, a resume button, bicolor LED,
>> >> and camera connector. Say Y here if you have this board.
>> >
>> > Shouldn't this go away as well?
>>
>> No, this one was incorrectly annotated, it's not actually
>> a board but it's an option for the OSK board that is not
>> getting removed. I considered making a separate patch
>> for removing the dependency, but that didn't seem worth it.
>
> OK. For the record, I don't think anyone has this add-on board anymore,
> and it has probably never been tested with the mainline kernel, so
> it's likely in the "dead code" category... Maybe it could be changed to
> "BROKEN", then the related OSK LCD panel stuff could be deleted later
> on too.
Ok, good to know. I left it in place for now because Tony originally
listed it as a likely used machine along with NOKIA770 and
AMS_DELTA [1], but I don't have anyone listed specifically as a
user for it.
It's not too late to revisit this list if you think it helps to
get rid of it. I can see that drivers/mtd/tps65010.c and
drivers/pcmcia/omap_cf.c become orphaned without it and can
probably get removed as well then.
Arnd
[1] https://lore.kernel.org/linux-arm-kernel/20220721150320.GA9385@macbook.musicnaut.iki.fi/
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 14/17] ARM: omap1: remove dead code
2022-10-19 17:34 ` Aaro Koskinen
@ 2022-10-21 7:51 ` Arnd Bergmann
0 siblings, 0 replies; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-21 7:51 UTC (permalink / raw)
To: Aaro Koskinen, Arnd Bergmann
Cc: linux-arm-kernel, Paul Walmsley, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Linux-OMAP, Kevin Hilman,
Mark Brown, Felipe Balbi, Greg Kroah-Hartman, Alan Stern,
Bin Liu, Helge Deller, linux-usb, linux-spi, linux-fbdev,
dri-devel
On Wed, Oct 19, 2022, at 19:34, Aaro Koskinen wrote:
> Hi,
>
> On Wed, Oct 19, 2022 at 05:03:36PM +0200, Arnd Bergmann wrote:
>> drivers/usb/phy/phy-isp1301-omap.c | 91 +-----------------------------
>
> This driver and config option ISP1301_OMAP can be deleted altogether as
> there are no users after H2/H3 boards are gone.
Good catch! I'll split the driver removal out as a separate patch
then and remove this bit here.
Arnd
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
2022-10-19 17:15 ` [PATCH 13/17] ARM: omap1: remove unused board files Aaro Koskinen
2022-10-19 19:30 ` Wolfram Sang
@ 2022-10-21 9:50 ` Lee Jones
2022-10-22 10:24 ` Greg Kroah-Hartman
2022-10-24 5:45 ` Tony Lindgren
4 siblings, 0 replies; 24+ messages in thread
From: Lee Jones @ 2022-10-21 9:50 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Arnd Bergmann, linux-omap,
Ulf Hansson, Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc, linux-usb
On Wed, 19 Oct 2022, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> All board support that was marked as 'unused' earlier can
> now be removed, leaving the five machines that that still
> had someone using them in 2022, or that are supported in
> qemu.
>
> Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: linux-omap@vger.kernel.org
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
> ---
> MAINTAINERS | 2 -
> arch/arm/Kconfig.debug | 36 +-
> arch/arm/configs/omap1_defconfig | 2 -
> arch/arm/mach-omap1/Kconfig | 93 +---
> arch/arm/mach-omap1/Makefile | 18 -
> arch/arm/mach-omap1/board-fsample.c | 366 ---------------
> arch/arm/mach-omap1/board-generic.c | 85 ----
> arch/arm/mach-omap1/board-h2-mmc.c | 74 ---
> arch/arm/mach-omap1/board-h2.c | 448 ------------------
> arch/arm/mach-omap1/board-h2.h | 38 --
> arch/arm/mach-omap1/board-h3-mmc.c | 64 ---
> arch/arm/mach-omap1/board-h3.c | 455 ------------------
> arch/arm/mach-omap1/board-h3.h | 35 --
> arch/arm/mach-omap1/board-htcherald.c | 585 ------------------------
> arch/arm/mach-omap1/board-innovator.c | 481 -------------------
> arch/arm/mach-omap1/board-nand.c | 33 --
> arch/arm/mach-omap1/board-palmtt.c | 285 ------------
> arch/arm/mach-omap1/board-palmz71.c | 300 ------------
> arch/arm/mach-omap1/board-perseus2.c | 333 --------------
> arch/arm/mach-omap1/fpga.c | 186 --------
> arch/arm/mach-omap1/fpga.h | 49 --
> arch/arm/mach-omap1/gpio7xx.c | 272 -----------
> drivers/i2c/busses/Kconfig | 2 +-
> drivers/mfd/Kconfig | 2 +-
Acked-by: Lee Jones <lee@kernel.org>
> drivers/mmc/host/Kconfig | 2 +-
> drivers/usb/gadget/udc/Kconfig | 2 +-
> drivers/usb/host/Kconfig | 2 +-
> include/linux/platform_data/leds-omap.h | 19 -
> 28 files changed, 12 insertions(+), 4257 deletions(-)
> delete mode 100644 arch/arm/mach-omap1/board-fsample.c
> delete mode 100644 arch/arm/mach-omap1/board-generic.c
> delete mode 100644 arch/arm/mach-omap1/board-h2-mmc.c
> delete mode 100644 arch/arm/mach-omap1/board-h2.c
> delete mode 100644 arch/arm/mach-omap1/board-h2.h
> delete mode 100644 arch/arm/mach-omap1/board-h3-mmc.c
> delete mode 100644 arch/arm/mach-omap1/board-h3.c
> delete mode 100644 arch/arm/mach-omap1/board-h3.h
> delete mode 100644 arch/arm/mach-omap1/board-htcherald.c
> delete mode 100644 arch/arm/mach-omap1/board-innovator.c
> delete mode 100644 arch/arm/mach-omap1/board-nand.c
> delete mode 100644 arch/arm/mach-omap1/board-palmtt.c
> delete mode 100644 arch/arm/mach-omap1/board-palmz71.c
> delete mode 100644 arch/arm/mach-omap1/board-perseus2.c
> delete mode 100644 arch/arm/mach-omap1/fpga.c
> delete mode 100644 arch/arm/mach-omap1/fpga.h
> delete mode 100644 arch/arm/mach-omap1/gpio7xx.c
> delete mode 100644 include/linux/platform_data/leds-omap.h
--
Lee Jones [李琼斯]
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-21 6:52 ` Arnd Bergmann
@ 2022-10-21 11:11 ` Aaro Koskinen
2022-10-24 5:49 ` Tony Lindgren
0 siblings, 1 reply; 24+ messages in thread
From: Aaro Koskinen @ 2022-10-21 11:11 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Arnd Bergmann, linux-arm-kernel, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Linux-OMAP, Lee Jones, Ulf Hansson,
Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc @ vger . kernel . org, linux-usb
Hi,
On Fri, Oct 21, 2022 at 08:52:10AM +0200, Arnd Bergmann wrote:
> On Thu, Oct 20, 2022, at 21:35, Aaro Koskinen wrote:
> > On Thu, Oct 20, 2022 at 09:11:11AM +0200, Arnd Bergmann wrote:
> >> On Wed, Oct 19, 2022, at 19:15, Aaro Koskinen wrote:
> >> > On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
> >> >> All board support that was marked as 'unused' earlier can
> >> >> now be removed, leaving the five machines that that still
> >> >> had someone using them in 2022, or that are supported in
> >> >> qemu.
> >> > [...]
> >> >> config OMAP_OSK_MISTRAL
> >> >> bool "Mistral QVGA board Support"
> >> >> depends on MACH_OMAP_OSK
> >> >> - depends on UNUSED_BOARD_FILES
> >> >> help
> >> >> The OSK supports an optional add-on board with a Quarter-VGA
> >> >> touchscreen, PDA-ish buttons, a resume button, bicolor LED,
> >> >> and camera connector. Say Y here if you have this board.
> >> >
> >> > Shouldn't this go away as well?
> >>
> >> No, this one was incorrectly annotated, it's not actually
> >> a board but it's an option for the OSK board that is not
> >> getting removed. I considered making a separate patch
> >> for removing the dependency, but that didn't seem worth it.
> >
> > OK. For the record, I don't think anyone has this add-on board anymore,
> > and it has probably never been tested with the mainline kernel, so
> > it's likely in the "dead code" category... Maybe it could be changed to
> > "BROKEN", then the related OSK LCD panel stuff could be deleted later
> > on too.
>
> Ok, good to know. I left it in place for now because Tony originally
> listed it as a likely used machine along with NOKIA770 and
> AMS_DELTA [1], but I don't have anyone listed specifically as a
> user for it.
>
> It's not too late to revisit this list if you think it helps to
> get rid of it. I can see that drivers/mtd/tps65010.c and
> drivers/pcmcia/omap_cf.c become orphaned without it and can
> probably get removed as well then.
I was only referring to this Mistral add-on board and related display
drivers.
The main OSK board support is still needed and used.
A.
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 14/17] ARM: omap1: remove dead code
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
2022-10-19 17:34 ` Aaro Koskinen
@ 2022-10-22 10:24 ` Greg Kroah-Hartman
2022-10-24 5:49 ` Tony Lindgren
2022-10-24 18:03 ` Kevin Hilman
3 siblings, 0 replies; 24+ messages in thread
From: Greg Kroah-Hartman @ 2022-10-22 10:24 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Paul Walmsley, Aaro Koskinen,
Janusz Krzysztofik, Tony Lindgren, linux-kernel, Arnd Bergmann,
linux-omap, Kevin Hilman, Mark Brown, Felipe Balbi, Alan Stern,
Bin Liu, Helge Deller, linux-usb, linux-spi, linux-fbdev,
dri-devel
On Wed, Oct 19, 2022 at 05:03:36PM +0200, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> After the removal of the unused board files, I went through the
> omap1 code to look for code that no longer has any callers
> and remove that.
>
> In particular, support for the omap7xx/omap8xx family is now
> completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
>
> Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: linux-omap@vger.kernel.org
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
` (2 preceding siblings ...)
2022-10-21 9:50 ` Lee Jones
@ 2022-10-22 10:24 ` Greg Kroah-Hartman
2022-10-24 5:45 ` Tony Lindgren
4 siblings, 0 replies; 24+ messages in thread
From: Greg Kroah-Hartman @ 2022-10-22 10:24 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Aaro Koskinen, Janusz Krzysztofik,
Tony Lindgren, linux-kernel, Arnd Bergmann, linux-omap,
Lee Jones, Ulf Hansson, Felipe Balbi, linux-i2c, linux-mmc,
linux-usb
On Wed, Oct 19, 2022 at 05:03:35PM +0200, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> All board support that was marked as 'unused' earlier can
> now be removed, leaving the five machines that that still
> had someone using them in 2022, or that are supported in
> qemu.
>
> Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
> Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: linux-omap@vger.kernel.org
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
` (3 preceding siblings ...)
2022-10-22 10:24 ` Greg Kroah-Hartman
@ 2022-10-24 5:45 ` Tony Lindgren
4 siblings, 0 replies; 24+ messages in thread
From: Tony Lindgren @ 2022-10-24 5:45 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Aaro Koskinen, Janusz Krzysztofik,
linux-kernel, Arnd Bergmann, linux-omap, Lee Jones, Ulf Hansson,
Felipe Balbi, Greg Kroah-Hartman, linux-i2c, linux-mmc,
linux-usb
* Arnd Bergmann <arnd@kernel.org> [221019 15:08]:
> From: Arnd Bergmann <arnd@arndb.de>
>
> All board support that was marked as 'unused' earlier can
> now be removed, leaving the five machines that that still
> had someone using them in 2022, or that are supported in
> qemu.
Acked-by: Tony Lindgren <tony@atomide.com>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-21 11:11 ` Aaro Koskinen
@ 2022-10-24 5:49 ` Tony Lindgren
2022-10-24 16:02 ` Arnd Bergmann
0 siblings, 1 reply; 24+ messages in thread
From: Tony Lindgren @ 2022-10-24 5:49 UTC (permalink / raw)
To: Aaro Koskinen
Cc: Arnd Bergmann, Arnd Bergmann, linux-arm-kernel,
Janusz Krzysztofik, linux-kernel, Linux-OMAP, Lee Jones,
Ulf Hansson, Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc @ vger . kernel . org, linux-usb
* Aaro Koskinen <aaro.koskinen@iki.fi> [221021 11:02]:
> I was only referring to this Mistral add-on board and related display
> drivers.
>
> The main OSK board support is still needed and used.
I'm pretty sure I have that display, but I was booting my OSK in a
rack anyways so I rarely saw the LCD in use. No objections from me
for removing the LCD support for OSK if nobody is using it.
Regards,
Tony
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 14/17] ARM: omap1: remove dead code
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
2022-10-19 17:34 ` Aaro Koskinen
2022-10-22 10:24 ` Greg Kroah-Hartman
@ 2022-10-24 5:49 ` Tony Lindgren
2022-10-24 18:03 ` Kevin Hilman
3 siblings, 0 replies; 24+ messages in thread
From: Tony Lindgren @ 2022-10-24 5:49 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Paul Walmsley, Aaro Koskinen,
Janusz Krzysztofik, linux-kernel, Arnd Bergmann, linux-omap,
Kevin Hilman, Mark Brown, Felipe Balbi, Greg Kroah-Hartman,
Alan Stern, Bin Liu, Helge Deller, linux-usb, linux-spi,
linux-fbdev, dri-devel
* Arnd Bergmann <arnd@kernel.org> [221019 15:10]:
> From: Arnd Bergmann <arnd@arndb.de>
>
> After the removal of the unused board files, I went through the
> omap1 code to look for code that no longer has any callers
> and remove that.
>
> In particular, support for the omap7xx/omap8xx family is now
> completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
Acked-by: Tony Lindgren <tony@atomide.com>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 15/17] fbdev: omapfb: remove unused board support
2022-10-19 15:03 ` [PATCH 15/17] fbdev: omapfb: remove unused board support Arnd Bergmann
@ 2022-10-24 5:50 ` Tony Lindgren
0 siblings, 0 replies; 24+ messages in thread
From: Tony Lindgren @ 2022-10-24 5:50 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Helge Deller, linux-kernel, Arnd Bergmann,
Aaro Koskinen, Janusz Krzysztofik, linux-omap, Marek Vasut,
Angelo Arrifano, Imre Deak, Bartlomiej Zolnierkiewicz,
linux-fbdev, dri-devel
* Arnd Bergmann <arnd@kernel.org> [221019 15:11]:
> From: Arnd Bergmann <arnd@arndb.de>
>
> A number of omap1 based board files got removed, so the corresponding
> framebuffer drivers are no longer used. The remaining ones are for
> ams_delta, osk and palmTE, which are still part of the mainline kernel.
Acked-by: Tony Lindgren <tony@atomide.com>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 16/17] spi: remove omap 100K driver
2022-10-19 15:03 ` [PATCH 16/17] spi: remove omap 100K driver Arnd Bergmann
2022-10-19 15:29 ` Mark Brown
@ 2022-10-24 5:50 ` Tony Lindgren
1 sibling, 0 replies; 24+ messages in thread
From: Tony Lindgren @ 2022-10-24 5:50 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-arm-kernel, Mark Brown, linux-kernel, Arnd Bergmann,
Aaro Koskinen, Janusz Krzysztofik, linux-omap, Cory Maccarrone,
Fabrice Crohas, linux-spi
* Arnd Bergmann <arnd@kernel.org> [221019 15:12]:
> From: Arnd Bergmann <arnd@arndb.de>
>
> The OMAP7xx/OMAP8xx support was removed since all of its boards
> have no remaining users. Remove its spi driver as well.
Acked-by: Tony Lindgren <tony@atomide.com>
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-24 5:49 ` Tony Lindgren
@ 2022-10-24 16:02 ` Arnd Bergmann
2022-10-25 8:08 ` Tony Lindgren
0 siblings, 1 reply; 24+ messages in thread
From: Arnd Bergmann @ 2022-10-24 16:02 UTC (permalink / raw)
To: Tony Lindgren, Aaro Koskinen
Cc: Arnd Bergmann, linux-arm-kernel, Janusz Krzysztofik,
linux-kernel, Linux-OMAP, Lee Jones, Ulf Hansson, Felipe Balbi,
Greg Kroah-Hartman, linux-i2c, linux-mmc @ vger . kernel . org,
linux-usb
On Mon, Oct 24, 2022, at 07:49, Tony Lindgren wrote:
> * Aaro Koskinen <aaro.koskinen@iki.fi> [221021 11:02]:
>> I was only referring to this Mistral add-on board and related display
>> drivers.
>>
>> The main OSK board support is still needed and used.
Ok, got it.
> I'm pretty sure I have that display, but I was booting my OSK in a
> rack anyways so I rarely saw the LCD in use. No objections from me
> for removing the LCD support for OSK if nobody is using it.
I was going to leave Mistral in, thinking it's just a device definition,
but upon closer look I found that this is a somewhat annoyingly
written part that hardcodes GPIO numbers in unusual ways, so I'm
adding a patch to remove it now.
Arnd
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 14/17] ARM: omap1: remove dead code
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
` (2 preceding siblings ...)
2022-10-24 5:49 ` Tony Lindgren
@ 2022-10-24 18:03 ` Kevin Hilman
3 siblings, 0 replies; 24+ messages in thread
From: Kevin Hilman @ 2022-10-24 18:03 UTC (permalink / raw)
To: Arnd Bergmann, linux-arm-kernel, Paul Walmsley, Aaro Koskinen,
Janusz Krzysztofik, Tony Lindgren
Cc: linux-kernel, Arnd Bergmann, linux-omap, Mark Brown,
Felipe Balbi, Greg Kroah-Hartman, Alan Stern, Bin Liu,
Helge Deller, linux-usb, linux-spi, linux-fbdev, dri-devel
Arnd Bergmann <arnd@kernel.org> writes:
> From: Arnd Bergmann <arnd@arndb.de>
>
> After the removal of the unused board files, I went through the
> omap1 code to look for code that no longer has any callers
> and remove that.
>
> In particular, support for the omap7xx/omap8xx family is now
> completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
Acked-by: Kevin Hilman <khilman@baylibre.com>
with a few tears shed since omap7xx/omap8xx was the first family I
contributed to upstream. :(
Kevin
^ permalink raw reply [flat|nested] 24+ messages in thread
* Re: [PATCH 13/17] ARM: omap1: remove unused board files
2022-10-24 16:02 ` Arnd Bergmann
@ 2022-10-25 8:08 ` Tony Lindgren
0 siblings, 0 replies; 24+ messages in thread
From: Tony Lindgren @ 2022-10-25 8:08 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Aaro Koskinen, Arnd Bergmann, linux-arm-kernel,
Janusz Krzysztofik, linux-kernel, Linux-OMAP, Lee Jones,
Ulf Hansson, Felipe Balbi, Greg Kroah-Hartman, linux-i2c,
linux-mmc @ vger . kernel . org, linux-usb
* Arnd Bergmann <arnd@arndb.de> [221024 15:53]:
> On Mon, Oct 24, 2022, at 07:49, Tony Lindgren wrote:
> > * Aaro Koskinen <aaro.koskinen@iki.fi> [221021 11:02]:
> >> I was only referring to this Mistral add-on board and related display
> >> drivers.
> >>
> >> The main OSK board support is still needed and used.
>
> Ok, got it.
>
> > I'm pretty sure I have that display, but I was booting my OSK in a
> > rack anyways so I rarely saw the LCD in use. No objections from me
> > for removing the LCD support for OSK if nobody is using it.
>
> I was going to leave Mistral in, thinking it's just a device definition,
> but upon closer look I found that this is a somewhat annoyingly
> written part that hardcodes GPIO numbers in unusual ways, so I'm
> adding a patch to remove it now.
OK sounds good to me.
Thanks,
Tony
^ permalink raw reply [flat|nested] 24+ messages in thread
end of thread, other threads:[~2022-10-25 8:08 UTC | newest]
Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-10-19 14:40 [PATCH 00/17] ARM: remove old board files Arnd Bergmann
[not found] ` <20221019150410.3851944-1-arnd@kernel.org>
2022-10-19 15:03 ` [PATCH 14/17] ARM: omap1: remove dead code Arnd Bergmann
2022-10-19 17:34 ` Aaro Koskinen
2022-10-21 7:51 ` Arnd Bergmann
2022-10-22 10:24 ` Greg Kroah-Hartman
2022-10-24 5:49 ` Tony Lindgren
2022-10-24 18:03 ` Kevin Hilman
2022-10-19 15:03 ` [PATCH 15/17] fbdev: omapfb: remove unused board support Arnd Bergmann
2022-10-24 5:50 ` Tony Lindgren
2022-10-19 15:03 ` [PATCH 16/17] spi: remove omap 100K driver Arnd Bergmann
2022-10-19 15:29 ` Mark Brown
2022-10-24 5:50 ` Tony Lindgren
[not found] ` <20221019150410.3851944-13-arnd@kernel.org>
2022-10-19 17:15 ` [PATCH 13/17] ARM: omap1: remove unused board files Aaro Koskinen
2022-10-20 7:11 ` Arnd Bergmann
2022-10-20 19:35 ` Aaro Koskinen
2022-10-21 6:52 ` Arnd Bergmann
2022-10-21 11:11 ` Aaro Koskinen
2022-10-24 5:49 ` Tony Lindgren
2022-10-24 16:02 ` Arnd Bergmann
2022-10-25 8:08 ` Tony Lindgren
2022-10-19 19:30 ` Wolfram Sang
2022-10-21 9:50 ` Lee Jones
2022-10-22 10:24 ` Greg Kroah-Hartman
2022-10-24 5:45 ` Tony Lindgren
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).