[PATCH v7 0/3] PCI: qcom: ep: Add basic interconnect support

[PATCH v7 0/3] PCI: qcom: ep: Add basic interconnect support

[Krishna chaitanya chundru]

Add basic support for managing "pcie-mem" interconnect path by setting
a low constraint before enabling clocks and updating it after the link
is up based on link speed and width the device got enumerated.

chnages from v6:
	- addressed the comments as suggested by mani.
changes from v5:
        - addressed the comments by mani.
changes from v4:
        - rebased with linux-next.
        - Added comments as suggested by mani.
        - removed the arm: dts: qcom: sdx55: Add interconnect path
          as that patch is already applied.
changes from v3:
        - ran make DT_CHECKER_FLAGS=-m dt_binding_check and fixed
         errors.
        - Added macros in the qcom ep driver patch as suggested by Dmitry
changes from v2:
        - changed the logic for getting speed and width as suggested
         by bjorn.
        - fixed compilation errors.


Krishna chaitanya chundru (3):
  dt-bindings: PCI: qcom: ep: Add interconnects path
  arm: dts: qcom: sdx65: Add PCIe interconnect path
  PCI: qcom-ep: Add ICC bandwidth voting support

 .../devicetree/bindings/pci/qcom,pcie-ep.yaml      | 13 ++++
 arch/arm/boot/dts/qcom/qcom-sdx65.dtsi             |  3 +
 drivers/pci/controller/dwc/pcie-qcom-ep.c          | 71 ++++++++++++++++++++++
 3 files changed, 87 insertions(+)

-- 
2.7.4

[PATCH v7 1/3] dt-bindings: PCI: qcom: ep: Add interconnects path

[Krishna chaitanya chundru]

Some platforms may not boot if a device driver doesn't
initialize the interconnect path. Mostly it is handled
by the bootloader but we have starting to see cases
where bootloader simply ignores them.

Add the "pcie-mem" interconnect path as a required property
to the bindings.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
index 8111122..bc32e13 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie-ep.yaml
@@ -71,6 +71,13 @@ properties:
     description: GPIO used as WAKE# output signal
     maxItems: 1
 
+  interconnects:
+    maxItems: 1
+
+  interconnect-names:
+    items:
+      - const: pcie-mem
+
   resets:
     maxItems: 1
 
@@ -98,6 +105,8 @@ required:
   - interrupts
   - interrupt-names
   - reset-gpios
+  - interconnects
+  - interconnect-names
   - resets
   - reset-names
   - power-domains
@@ -167,7 +176,9 @@ examples:
   - |
     #include <dt-bindings/clock/qcom,gcc-sdx55.h>
     #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interconnect/qcom,sdx55.h>
     #include <dt-bindings/interrupt-controller/arm-gic.h>
+
     pcie_ep: pcie-ep@1c00000 {
         compatible = "qcom,sdx55-pcie-ep";
         reg = <0x01c00000 0x3000>,
@@ -194,6 +205,8 @@ examples:
         interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
         interrupt-names = "global", "doorbell";
+        interconnects = <&system_noc MASTER_PCIE &mc_virt SLAVE_EBI_CH0>;
+        interconnect-names = "pcie-mem";
         reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
         wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
         resets = <&gcc GCC_PCIE_BCR>;
-- 
2.7.4

[PATCH v7 2/3] arm: dts: qcom: sdx65: Add PCIe interconnect path

[Krishna chaitanya chundru]

Add pcie-mem interconnect path to sdx65 platform.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
---
 arch/arm/boot/dts/qcom/qcom-sdx65.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
index 1a35830..77fa97c 100644
--- a/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-sdx65.dtsi
@@ -332,6 +332,9 @@
 				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "global", "doorbell";
 
+			interconnects = <&system_noc MASTER_PCIE_0 &mc_virt SLAVE_EBI1>;
+			interconnect-names = "pcie-mem";
+
 			resets = <&gcc GCC_PCIE_BCR>;
 			reset-names = "core";
 
-- 
2.7.4

[PATCH v7 3/3] PCI: qcom-ep: Add ICC bandwidth voting support

[Krishna chaitanya chundru]

Add support for voting interconnect (ICC) bandwidth based
on the link speed and width.

This commit is inspired from the basic interconnect support added
to pcie-qcom driver in commit c4860af88d0c ("PCI: qcom: Add basic
interconnect support").

The interconnect support is kept optional to be backward compatible
with legacy devicetrees.

Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
---
 drivers/pci/controller/dwc/pcie-qcom-ep.c | 71 +++++++++++++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
index 1435f51..cfe3061 100644
--- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
+++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
@@ -13,6 +13,7 @@
 #include <linux/debugfs.h>
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
+#include <linux/interconnect.h>
 #include <linux/mfd/syscon.h>
 #include <linux/phy/pcie.h>
 #include <linux/phy/phy.h>
@@ -28,6 +29,7 @@
 #define PARF_SYS_CTRL				0x00
 #define PARF_DB_CTRL				0x10
 #define PARF_PM_CTRL				0x20
+#define PARF_PM_STTS				0x24
 #define PARF_MHI_CLOCK_RESET_CTRL		0x174
 #define PARF_MHI_BASE_ADDR_LOWER		0x178
 #define PARF_MHI_BASE_ADDR_UPPER		0x17c
@@ -133,6 +135,11 @@
 #define CORE_RESET_TIME_US_MAX			1005
 #define WAKE_DELAY_US				2000 /* 2 ms */
 
+#define PCIE_GEN1_BW_MBPS			250
+#define PCIE_GEN2_BW_MBPS			500
+#define PCIE_GEN3_BW_MBPS			985
+#define PCIE_GEN4_BW_MBPS			1969
+
 #define to_pcie_ep(x)				dev_get_drvdata((x)->dev)
 
 enum qcom_pcie_ep_link_status {
@@ -178,6 +185,8 @@ struct qcom_pcie_ep {
 	struct phy *phy;
 	struct dentry *debugfs;
 
+	struct icc_path *icc_mem;
+
 	struct clk_bulk_data *clks;
 	int num_clks;
 
@@ -253,8 +262,49 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
 	disable_irq(pcie_ep->perst_irq);
 }
 
+static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
+{
+	struct dw_pcie *pci = &pcie_ep->pci;
+	u32 offset, status, bw;
+	int speed, width;
+	int ret;
+
+	if (!pcie_ep->icc_mem)
+		return;
+
+	offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
+	status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
+
+	speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
+	width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
+
+	switch (speed) {
+	case 1:
+		bw = MBps_to_icc(PCIE_GEN1_BW_MBPS);
+		break;
+	case 2:
+		bw = MBps_to_icc(PCIE_GEN2_BW_MBPS);
+		break;
+	case 3:
+		bw = MBps_to_icc(PCIE_GEN3_BW_MBPS);
+		break;
+	default:
+		dev_warn(pci->dev, "using default GEN4 bandwidth\n");
+		fallthrough;
+	case 4:
+		bw = MBps_to_icc(PCIE_GEN4_BW_MBPS);
+		break;
+	}
+
+	ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
+	if (ret)
+		dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+			ret);
+}
+
 static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
 {
+	struct dw_pcie *pci = &pcie_ep->pci;
 	int ret;
 
 	ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
@@ -277,8 +327,24 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
 	if (ret)
 		goto err_phy_exit;
 
+	/*
+	 * Some Qualcomm platforms require interconnect bandwidth constraints
+	 * to be set before enabling interconnect clocks.
+	 *
+	 * Set an initial peak bandwidth corresponding to single-lane Gen 1
+	 * for the pcie-mem path.
+	 */
+	ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(PCIE_GEN1_BW_MBPS));
+	if (ret) {
+		dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
+			ret);
+		goto err_phy_off;
+	}
+
 	return 0;
 
+err_phy_off:
+	phy_power_off(pcie_ep->phy);
 err_phy_exit:
 	phy_exit(pcie_ep->phy);
 err_disable_clk:
@@ -550,6 +616,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
 	if (IS_ERR(pcie_ep->phy))
 		ret = PTR_ERR(pcie_ep->phy);
 
+	pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
+	if (IS_ERR(pcie_ep->icc_mem))
+		ret = PTR_ERR(pcie_ep->icc_mem);
+
 	return ret;
 }
 
@@ -573,6 +643,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
 	} else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
 		dev_dbg(dev, "Received BME event. Link is enabled!\n");
 		pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
+		qcom_pcie_ep_icc_update(pcie_ep);
 		pci_epc_bme_notify(pci->ep.epc);
 	} else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
 		dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
-- 
2.7.4

Re: [PATCH v7 0/3] PCI: qcom: ep: Add basic interconnect support

[Krishna Chaitanya Chundru]

Hi All,

A gentle ping.


Thanks,

KC

On 6/30/2023 9:55 AM, Krishna chaitanya chundru wrote:
> Add basic support for managing "pcie-mem" interconnect path by setting
> a low constraint before enabling clocks and updating it after the link
> is up based on link speed and width the device got enumerated.
>
> chnages from v6:
> 	- addressed the comments as suggested by mani.
> changes from v5:
>          - addressed the comments by mani.
> changes from v4:
>          - rebased with linux-next.
>          - Added comments as suggested by mani.
>          - removed the arm: dts: qcom: sdx55: Add interconnect path
>            as that patch is already applied.
> changes from v3:
>          - ran make DT_CHECKER_FLAGS=-m dt_binding_check and fixed
>           errors.
>          - Added macros in the qcom ep driver patch as suggested by Dmitry
> changes from v2:
>          - changed the logic for getting speed and width as suggested
>           by bjorn.
>          - fixed compilation errors.
>
>
> Krishna chaitanya chundru (3):
>    dt-bindings: PCI: qcom: ep: Add interconnects path
>    arm: dts: qcom: sdx65: Add PCIe interconnect path
>    PCI: qcom-ep: Add ICC bandwidth voting support
>
>   .../devicetree/bindings/pci/qcom,pcie-ep.yaml      | 13 ++++
>   arch/arm/boot/dts/qcom/qcom-sdx65.dtsi             |  3 +
>   drivers/pci/controller/dwc/pcie-qcom-ep.c          | 71 ++++++++++++++++++++++
>   3 files changed, 87 insertions(+)
>

Re: [PATCH v7 3/3] PCI: qcom-ep: Add ICC bandwidth voting support

[Manivannan Sadhasivam]

On Fri, Jun 30, 2023 at 09:55:23AM +0530, Krishna chaitanya chundru wrote:
> Add support for voting interconnect (ICC) bandwidth based
> on the link speed and width.
> 
> This commit is inspired from the basic interconnect support added
> to pcie-qcom driver in commit c4860af88d0c ("PCI: qcom: Add basic
> interconnect support").
> 
> The interconnect support is kept optional to be backward compatible
> with legacy devicetrees.
> 
> Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
> ---
>  drivers/pci/controller/dwc/pcie-qcom-ep.c | 71 +++++++++++++++++++++++++++++++
>  1 file changed, 71 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> index 1435f51..cfe3061 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> @@ -13,6 +13,7 @@
>  #include <linux/debugfs.h>
>  #include <linux/delay.h>
>  #include <linux/gpio/consumer.h>
> +#include <linux/interconnect.h>
>  #include <linux/mfd/syscon.h>
>  #include <linux/phy/pcie.h>
>  #include <linux/phy/phy.h>
> @@ -28,6 +29,7 @@
>  #define PARF_SYS_CTRL				0x00
>  #define PARF_DB_CTRL				0x10
>  #define PARF_PM_CTRL				0x20
> +#define PARF_PM_STTS				0x24
>  #define PARF_MHI_CLOCK_RESET_CTRL		0x174
>  #define PARF_MHI_BASE_ADDR_LOWER		0x178
>  #define PARF_MHI_BASE_ADDR_UPPER		0x17c
> @@ -133,6 +135,11 @@
>  #define CORE_RESET_TIME_US_MAX			1005
>  #define WAKE_DELAY_US				2000 /* 2 ms */
>  
> +#define PCIE_GEN1_BW_MBPS			250
> +#define PCIE_GEN2_BW_MBPS			500
> +#define PCIE_GEN3_BW_MBPS			985
> +#define PCIE_GEN4_BW_MBPS			1969
> +
>  #define to_pcie_ep(x)				dev_get_drvdata((x)->dev)
>  
>  enum qcom_pcie_ep_link_status {
> @@ -178,6 +185,8 @@ struct qcom_pcie_ep {
>  	struct phy *phy;
>  	struct dentry *debugfs;
>  
> +	struct icc_path *icc_mem;
> +
>  	struct clk_bulk_data *clks;
>  	int num_clks;
>  
> @@ -253,8 +262,49 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
>  	disable_irq(pcie_ep->perst_irq);
>  }
>  
> +static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
> +{
> +	struct dw_pcie *pci = &pcie_ep->pci;
> +	u32 offset, status, bw;
> +	int speed, width;
> +	int ret;
> +
> +	if (!pcie_ep->icc_mem)
> +		return;
> +
> +	offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> +	status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
> +
> +	speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
> +	width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
> +
> +	switch (speed) {
> +	case 1:
> +		bw = MBps_to_icc(PCIE_GEN1_BW_MBPS);
> +		break;
> +	case 2:
> +		bw = MBps_to_icc(PCIE_GEN2_BW_MBPS);
> +		break;
> +	case 3:
> +		bw = MBps_to_icc(PCIE_GEN3_BW_MBPS);
> +		break;
> +	default:
> +		dev_warn(pci->dev, "using default GEN4 bandwidth\n");
> +		fallthrough;
> +	case 4:
> +		bw = MBps_to_icc(PCIE_GEN4_BW_MBPS);
> +		break;
> +	}
> +
> +	ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
> +	if (ret)
> +		dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> +			ret);
> +}
> +
>  static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>  {
> +	struct dw_pcie *pci = &pcie_ep->pci;
>  	int ret;
>  
>  	ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
> @@ -277,8 +327,24 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>  	if (ret)
>  		goto err_phy_exit;
>  
> +	/*
> +	 * Some Qualcomm platforms require interconnect bandwidth constraints
> +	 * to be set before enabling interconnect clocks.
> +	 *
> +	 * Set an initial peak bandwidth corresponding to single-lane Gen 1
> +	 * for the pcie-mem path.
> +	 */
> +	ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(PCIE_GEN1_BW_MBPS));
> +	if (ret) {
> +		dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> +			ret);
> +		goto err_phy_off;
> +	}
> +

You need to set bw to 0 during disable_resources() as well. Otherwise, it will
result in resource leakage when the driver is not in use.

- Mani

>  	return 0;
>  
> +err_phy_off:
> +	phy_power_off(pcie_ep->phy);
>  err_phy_exit:
>  	phy_exit(pcie_ep->phy);
>  err_disable_clk:
> @@ -550,6 +616,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
>  	if (IS_ERR(pcie_ep->phy))
>  		ret = PTR_ERR(pcie_ep->phy);
>  
> +	pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
> +	if (IS_ERR(pcie_ep->icc_mem))
> +		ret = PTR_ERR(pcie_ep->icc_mem);
> +
>  	return ret;
>  }
>  
> @@ -573,6 +643,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
>  	} else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
>  		dev_dbg(dev, "Received BME event. Link is enabled!\n");
>  		pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
> +		qcom_pcie_ep_icc_update(pcie_ep);
>  		pci_epc_bme_notify(pci->ep.epc);
>  	} else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
>  		dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
> -- 
> 2.7.4
> 

-- 
மணிவண்ணன் சதாசிவம்