linux-pci.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Sinan Kaya <okaya@kernel.org>
To: linux-pci@vger.kernel.org
Cc: Sinan Kaya <okaya@kernel.org>,
	Bjorn Helgaas <bhelgaas@google.com>,
	Lukas Wunner <lukas@wunner.de>,
	Mika Westerberg <mika.westerberg@linux.intel.com>,
	"Gustavo A. R. Silva" <gustavo@embeddedor.com>,
	Oza Pawandeep <poza@codeaurora.org>,
	Keith Busch <keith.busch@intel.com>,
	linux-kernel@vger.kernel.org (open list)
Subject: [PATCH v8 1/2] PCI: pciehp: Ignore link events when there is a fatal error pending
Date: Fri, 17 Aug 2018 23:51:09 -0700	[thread overview]
Message-ID: <20180818065126.77912-1-okaya@kernel.org> (raw)

AER/DPC reset is known as warm-resets. HP link recovery is known as
cold-reset via power-off and power-on command to the PCI slot.

In the middle of a warm-reset operation (AER/DPC), we are:

1. turning off the slow power. Slot power needs to be kept on in order
for recovery to succeed.

2. performing a cold reset causing Fatal Error recovery to fail.

If link goes down due to a DPC event, it should be recovered by DPC
status trigger. Injecting a cold reset in the middle can cause a HW
lockup as it is an undefined behavior.

Similarly, If link goes down due to an AER secondary bus reset issue,
it should be recovered by HW. Injecting a cold reset in the middle of a
secondary bus reset can cause a HW lockup as it is an undefined behavior.

1. HP ISR observes link down interrupt.
2. HP ISR checks that there is a fatal error pending, it doesn't touch
the link.
3. HP ISR waits until link recovery happens.
4. HP ISR calls the read vendor id function.
5. If all fails, try the cold-reset approach.

If fatal error is pending and a fatal error service such as DPC or AER
is running, it is the responsibility of the fatal error service to
recover the link.

Signed-off-by: Sinan Kaya <okaya@kernel.org>
---
 drivers/pci/hotplug/pciehp_ctrl.c | 18 ++++++++++++++++
 drivers/pci/pci.h                 |  2 ++
 drivers/pci/pcie/err.c            | 34 +++++++++++++++++++++++++++++++
 3 files changed, 54 insertions(+)

diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c
index da7c72372ffc..22354b6850c3 100644
--- a/drivers/pci/hotplug/pciehp_ctrl.c
+++ b/drivers/pci/hotplug/pciehp_ctrl.c
@@ -222,9 +222,27 @@ void pciehp_handle_disable_request(struct slot *slot)
 void pciehp_handle_presence_or_link_change(struct slot *slot, u32 events)
 {
 	struct controller *ctrl = slot->ctrl;
+	struct pci_dev *pdev = ctrl->pcie->port;
 	bool link_active;
 	u8 present;
 
+	/* If a fatal error is pending, wait for AER or DPC to handle it. */
+	if (pcie_fatal_error_pending(pdev)) {
+		bool recovered;
+
+		recovered = pcie_wait_fatal_error_clear(pdev);
+
+		/* If the fatal error is gone and the link is up, return */
+		if (recovered && pcie_wait_for_link(pdev, true)) {
+			ctrl_info(ctrl, "Slot(%s): Ignoring Link event due to successful fatal error recovery\n",
+				  slot_name(slot));
+			return;
+		}
+
+		ctrl_info(ctrl, "Slot(%s): Fatal error recovery failed for Link event, trying hotplug reset\n",
+			  slot_name(slot));
+	}
+
 	/*
 	 * If the slot is on and presence or link has changed, turn it off.
 	 * Even if it's occupied again, we cannot assume the card is the same.
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index c358e7a07f3f..e2d98654630b 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -356,6 +356,8 @@ void pci_enable_acs(struct pci_dev *dev);
 /* PCI error reporting and recovery */
 void pcie_do_fatal_recovery(struct pci_dev *dev, u32 service);
 void pcie_do_nonfatal_recovery(struct pci_dev *dev);
+bool pcie_fatal_error_pending(struct pci_dev *pdev);
+bool pcie_wait_fatal_error_clear(struct pci_dev *pdev);
 
 bool pcie_wait_for_link(struct pci_dev *pdev, bool active);
 #ifdef CONFIG_PCIEASPM
diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
index f7ce0cb0b0b7..b1b5604cb00b 100644
--- a/drivers/pci/pcie/err.c
+++ b/drivers/pci/pcie/err.c
@@ -16,6 +16,7 @@
 #include <linux/kernel.h>
 #include <linux/errno.h>
 #include <linux/aer.h>
+#include <linux/delay.h>
 #include "portdrv.h"
 #include "../pci.h"
 
@@ -386,3 +387,36 @@ void pcie_do_nonfatal_recovery(struct pci_dev *dev)
 	/* TODO: Should kernel panic here? */
 	pci_info(dev, "AER: Device recovery failed\n");
 }
+
+bool pcie_fatal_error_pending(struct pci_dev *pdev)
+{
+	u16 err_status = 0;
+	int rc;
+
+	if (!pci_is_pcie(pdev))
+		return false;
+
+	rc = pcie_capability_read_word(pdev, PCI_EXP_DEVSTA, &err_status);
+	if (rc)
+		return false;
+
+	return !!(err_status & PCI_EXP_DEVSTA_FED);
+}
+
+bool pcie_wait_fatal_error_clear(struct pci_dev *pdev)
+{
+	int timeout = 1000;
+	bool ret;
+
+	for (;;) {
+		ret = pcie_fatal_error_pending(pdev);
+		if (ret == false)
+			return true;
+		if (timeout <= 0)
+			break;
+		msleep(20);
+		timeout -= 20;
+	}
+
+	return false;
+}
-- 
2.17.1

             reply	other threads:[~2018-08-20  2:32 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-08-18  6:51 Sinan Kaya [this message]
2018-08-18  6:51 ` [PATCH v8 2/2] PCI: pciehp: Mask AER surprise link down error if hotplug is enabled Sinan Kaya
2018-08-19 23:23   ` Sinan Kaya
2018-08-20  0:20   ` kbuild test robot
2018-08-20  8:21   ` Lukas Wunner
2018-08-20 17:43     ` Sinan Kaya
2018-08-20  9:22 ` [PATCH v8 1/2] PCI: pciehp: Ignore link events when there is a fatal error pending Lukas Wunner
2018-08-20 16:59   ` Sinan Kaya
2018-08-20 17:22     ` Lukas Wunner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180818065126.77912-1-okaya@kernel.org \
    --to=okaya@kernel.org \
    --cc=bhelgaas@google.com \
    --cc=gustavo@embeddedor.com \
    --cc=keith.busch@intel.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=lukas@wunner.de \
    --cc=mika.westerberg@linux.intel.com \
    --cc=poza@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).