From: Changbin Du <changbin.du@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>,
rjw@rjwysocki.net, linux-pci@vger.kernel.org,
linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org,
tglx@linutronix.de, mingo@redhat.com, x86@kernel.org,
fenghua.yu@intel.com, linuxppc-dev@lists.ozlabs.org,
linux-acpi@vger.kernel.org, linux-gpio@vger.kernel.org,
mchehab+samsung@kernel.org, Changbin Du <changbin.du@gmail.com>
Subject: [PATCH v4 43/63] Documentation: x86: convert earlyprintk.txt to reST
Date: Wed, 24 Apr 2019 00:29:12 +0800 [thread overview]
Message-ID: <20190423162932.21428-44-changbin.du@gmail.com> (raw)
In-Reply-To: <20190423162932.21428-1-changbin.du@gmail.com>
This converts the plain text documentation to reStructuredText format and
add it to Sphinx TOC tree. No essential content change.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
---
Documentation/x86/earlyprintk.rst | 148 ++++++++++++++++++++++++++++++
Documentation/x86/earlyprintk.txt | 141 ----------------------------
Documentation/x86/index.rst | 1 +
3 files changed, 149 insertions(+), 141 deletions(-)
create mode 100644 Documentation/x86/earlyprintk.rst
delete mode 100644 Documentation/x86/earlyprintk.txt
diff --git a/Documentation/x86/earlyprintk.rst b/Documentation/x86/earlyprintk.rst
new file mode 100644
index 000000000000..519402451f9c
--- /dev/null
+++ b/Documentation/x86/earlyprintk.rst
@@ -0,0 +1,148 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+============
+Early Printk
+============
+
+Mini-HOWTO for using the earlyprintk=dbgp boot option with a
+USB2 Debug port key and a debug cable, on x86 systems.
+
+You need two computers, the 'USB debug key' special gadget and
+and two USB cables, connected like this::
+
+ [host/target] <-------> [USB debug key] <-------> [client/console]
+
+There are a number of specific hardware requirements
+====================================================
+
+ a) Host/target system needs to have USB debug port capability.
+
+ You can check this capability by looking at a 'Debug port' bit in
+ the lspci -vvv output::
+
+ # lspci -vvv
+ ...
+ 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
+ Subsystem: Lenovo ThinkPad T61
+ Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
+ Latency: 0
+ Interrupt: pin D routed to IRQ 19
+ Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
+ Capabilities: [50] Power Management version 2
+ Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
+ Status: D0 PME-Enable- DSel=0 DScale=0 PME+
+ Capabilities: [58] Debug port: BAR=1 offset=00a0
+ ^^^^^^^^^^^ <==================== [ HERE ]
+ Kernel driver in use: ehci_hcd
+ Kernel modules: ehci-hcd
+ ...
+
+ If your system does not list a debug port capability then you probably
+ won't be able to use the USB debug key.
+
+ b) You also need a NetChip USB debug cable/key:
+
+ http://www.plxtech.com/products/NET2000/NET20DC/default.asp
+
+ This is a small blue plastic connector with two USB connections;
+ it draws power from its USB connections.
+
+ c) You need a second client/console system with a high speed USB 2.0 port.
+
+ d) The NetChip device must be plugged directly into the physical
+ debug port on the "host/target" system. You cannot use a USB hub in
+ between the physical debug port and the "host/target" system.
+
+ The EHCI debug controller is bound to a specific physical USB
+ port and the NetChip device will only work as an early printk
+ device in this port. The EHCI host controllers are electrically
+ wired such that the EHCI debug controller is hooked up to the
+ first physical port and there is no way to change this via software.
+ You can find the physical port through experimentation by trying
+ each physical port on the system and rebooting. Or you can try
+ and use lsusb or look at the kernel info messages emitted by the
+ usb stack when you plug a usb device into various ports on the
+ "host/target" system.
+
+ Some hardware vendors do not expose the usb debug port with a
+ physical connector and if you find such a device send a complaint
+ to the hardware vendor, because there is no reason not to wire
+ this port into one of the physically accessible ports.
+
+ e) It is also important to note, that many versions of the NetChip
+ device require the "client/console" system to be plugged into the
+ right hand side of the device (with the product logo facing up and
+ readable left to right). The reason being is that the 5 volt
+ power supply is taken from only one side of the device and it
+ must be the side that does not get rebooted.
+
+Software requirements
+=====================
+
+ a) On the host/target system:
+
+ You need to enable the following kernel config option::
+
+ CONFIG_EARLY_PRINTK_DBGP=y
+
+ And you need to add the boot command line: "earlyprintk=dbgp".
+
+ .. note:: If you are using Grub, append it to the 'kernel' line in
+ /etc/grub.conf. If you are using Grub2 on a BIOS firmware system,
+ append it to the 'linux' line in /boot/grub2/grub.cfg. If you are
+ using Grub2 on an EFI firmware system, append it to the 'linux'
+ or 'linuxefi' line in /boot/grub2/grub.cfg or
+ /boot/efi/EFI/<distro>/grub.cfg.)
+
+ On systems with more than one EHCI debug controller you must
+ specify the correct EHCI debug controller number. The ordering
+ comes from the PCI bus enumeration of the EHCI controllers. The
+ default with no number argument is "0" or the first EHCI debug
+ controller. To use the second EHCI debug controller, you would
+ use the command line: "earlyprintk=dbgp1"
+
+ NOTE: normally earlyprintk console gets turned off once the
+ regular console is alive - use "earlyprintk=dbgp,keep" to keep
+ this channel open beyond early bootup. This can be useful for
+ debugging crashes under Xorg, etc.
+
+ b) On the client/console system:
+
+ You should enable the following kernel config option::
+
+ CONFIG_USB_SERIAL_DEBUG=y
+
+ On the next bootup with the modified kernel you should
+ get a /dev/ttyUSBx device(s).
+
+ Now this channel of kernel messages is ready to be used: start
+ your favorite terminal emulator (minicom, etc.) and set
+ it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to
+ see the raw output.
+
+ c) On Nvidia Southbridge based systems: the kernel will try to probe
+ and find out which port has a debug device connected.
+
+Testing that it works fine
+==========================
+
+ You can test the output by using earlyprintk=dbgp,keep and provoking
+ kernel messages on the host/target system. You can provoke a harmless
+ kernel message by for example doing::
+
+ echo h > /proc/sysrq-trigger
+
+ On the host/target system you should see this help line in "dmesg" output::
+
+ SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
+
+ On the client/console system do::
+
+ cat /dev/ttyUSB0
+
+ And you should see the help line above displayed shortly after you've
+ provoked it on the host system.
+
+If it does not work then please ask about it on the linux-kernel@vger.kernel.org
+mailing list or contact the x86 maintainers.
diff --git a/Documentation/x86/earlyprintk.txt b/Documentation/x86/earlyprintk.txt
deleted file mode 100644
index 46933e06c972..000000000000
--- a/Documentation/x86/earlyprintk.txt
+++ /dev/null
@@ -1,141 +0,0 @@
-
-Mini-HOWTO for using the earlyprintk=dbgp boot option with a
-USB2 Debug port key and a debug cable, on x86 systems.
-
-You need two computers, the 'USB debug key' special gadget and
-and two USB cables, connected like this:
-
- [host/target] <-------> [USB debug key] <-------> [client/console]
-
-1. There are a number of specific hardware requirements:
-
- a.) Host/target system needs to have USB debug port capability.
-
- You can check this capability by looking at a 'Debug port' bit in
- the lspci -vvv output:
-
- # lspci -vvv
- ...
- 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
- Subsystem: Lenovo ThinkPad T61
- Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Latency: 0
- Interrupt: pin D routed to IRQ 19
- Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
- Capabilities: [50] Power Management version 2
- Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
- Status: D0 PME-Enable- DSel=0 DScale=0 PME+
- Capabilities: [58] Debug port: BAR=1 offset=00a0
- ^^^^^^^^^^^ <==================== [ HERE ]
- Kernel driver in use: ehci_hcd
- Kernel modules: ehci-hcd
- ...
-
-( If your system does not list a debug port capability then you probably
- won't be able to use the USB debug key. )
-
- b.) You also need a NetChip USB debug cable/key:
-
- http://www.plxtech.com/products/NET2000/NET20DC/default.asp
-
- This is a small blue plastic connector with two USB connections;
- it draws power from its USB connections.
-
- c.) You need a second client/console system with a high speed USB 2.0
- port.
-
- d.) The NetChip device must be plugged directly into the physical
- debug port on the "host/target" system. You cannot use a USB hub in
- between the physical debug port and the "host/target" system.
-
- The EHCI debug controller is bound to a specific physical USB
- port and the NetChip device will only work as an early printk
- device in this port. The EHCI host controllers are electrically
- wired such that the EHCI debug controller is hooked up to the
- first physical port and there is no way to change this via software.
- You can find the physical port through experimentation by trying
- each physical port on the system and rebooting. Or you can try
- and use lsusb or look at the kernel info messages emitted by the
- usb stack when you plug a usb device into various ports on the
- "host/target" system.
-
- Some hardware vendors do not expose the usb debug port with a
- physical connector and if you find such a device send a complaint
- to the hardware vendor, because there is no reason not to wire
- this port into one of the physically accessible ports.
-
- e.) It is also important to note, that many versions of the NetChip
- device require the "client/console" system to be plugged into the
- right hand side of the device (with the product logo facing up and
- readable left to right). The reason being is that the 5 volt
- power supply is taken from only one side of the device and it
- must be the side that does not get rebooted.
-
-2. Software requirements:
-
- a.) On the host/target system:
-
- You need to enable the following kernel config option:
-
- CONFIG_EARLY_PRINTK_DBGP=y
-
- And you need to add the boot command line: "earlyprintk=dbgp".
-
- (If you are using Grub, append it to the 'kernel' line in
- /etc/grub.conf. If you are using Grub2 on a BIOS firmware system,
- append it to the 'linux' line in /boot/grub2/grub.cfg. If you are
- using Grub2 on an EFI firmware system, append it to the 'linux'
- or 'linuxefi' line in /boot/grub2/grub.cfg or
- /boot/efi/EFI/<distro>/grub.cfg.)
-
- On systems with more than one EHCI debug controller you must
- specify the correct EHCI debug controller number. The ordering
- comes from the PCI bus enumeration of the EHCI controllers. The
- default with no number argument is "0" or the first EHCI debug
- controller. To use the second EHCI debug controller, you would
- use the command line: "earlyprintk=dbgp1"
-
- NOTE: normally earlyprintk console gets turned off once the
- regular console is alive - use "earlyprintk=dbgp,keep" to keep
- this channel open beyond early bootup. This can be useful for
- debugging crashes under Xorg, etc.
-
- b.) On the client/console system:
-
- You should enable the following kernel config option:
-
- CONFIG_USB_SERIAL_DEBUG=y
-
- On the next bootup with the modified kernel you should
- get a /dev/ttyUSBx device(s).
-
- Now this channel of kernel messages is ready to be used: start
- your favorite terminal emulator (minicom, etc.) and set
- it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to
- see the raw output.
-
- c.) On Nvidia Southbridge based systems: the kernel will try to probe
- and find out which port has a debug device connected.
-
-3. Testing that it works fine:
-
- You can test the output by using earlyprintk=dbgp,keep and provoking
- kernel messages on the host/target system. You can provoke a harmless
- kernel message by for example doing:
-
- echo h > /proc/sysrq-trigger
-
- On the host/target system you should see this help line in "dmesg" output:
-
- SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
-
- On the client/console system do:
-
- cat /dev/ttyUSB0
-
- And you should see the help line above displayed shortly after you've
- provoked it on the host system.
-
-If it does not work then please ask about it on the linux-kernel@vger.kernel.org
-mailing list or contact the x86 maintainers.
diff --git a/Documentation/x86/index.rst b/Documentation/x86/index.rst
index 8a666c5abc85..7b8388ebd43d 100644
--- a/Documentation/x86/index.rst
+++ b/Documentation/x86/index.rst
@@ -13,3 +13,4 @@ Linux x86 Support
exception-tables
kernel-stacks
entry_64
+ earlyprintk
--
2.20.1
next prev parent reply other threads:[~2019-04-23 16:37 UTC|newest]
Thread overview: 123+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-23 16:28 [PATCH v4 00/63] Include linux ACPI/PCI/X86 docs into Sphinx TOC tree Changbin Du
2019-04-23 16:28 ` [PATCH v4 01/63] Documentation: add Linux ACPI to " Changbin Du
2019-04-23 20:39 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 02/63] Documentation: ACPI: move namespace.txt to firmware-guide/acpi and convert to reST Changbin Du
2019-04-23 20:38 ` Mauro Carvalho Chehab
2019-04-24 16:09 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 03/63] Documentation: ACPI: move enumeration.txt " Changbin Du
2019-04-23 20:42 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 04/63] Documentation: ACPI: move osi.txt " Changbin Du
2019-04-23 20:44 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 05/63] Documentation: ACPI: move linuxized-acpica.txt to driver-api/acpi " Changbin Du
2019-04-23 20:50 ` Mauro Carvalho Chehab
2019-04-24 16:15 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 06/63] Documentation: ACPI: move scan_handlers.txt " Changbin Du
2019-04-23 20:51 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 07/63] Documentation: ACPI: move DSD-properties-rules.txt to firmware-guide/acpi and covert " Changbin Du
2019-04-23 20:52 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 08/63] Documentation: ACPI: move gpio-properties.txt to firmware-guide/acpi and convert " Changbin Du
2019-04-23 20:55 ` Mauro Carvalho Chehab
2019-04-24 16:21 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 09/63] Documentation: ACPI: move method-customizing.txt " Changbin Du
2019-04-23 21:03 ` Mauro Carvalho Chehab
2019-04-24 16:28 ` Changbin Du
2019-04-24 17:53 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 10/63] Documentation: ACPI: move initrd_table_override.txt to admin-guide/acpi " Changbin Du
2019-04-23 21:07 ` Mauro Carvalho Chehab
2019-04-24 16:33 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 11/63] Documentation: ACPI: move dsdt-override.txt " Changbin Du
2019-04-23 21:08 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 12/63] Documentation: ACPI: move i2c-muxes.txt to firmware-guide/acpi " Changbin Du
2019-04-23 21:09 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 13/63] Documentation: ACPI: move acpi-lid.txt " Changbin Du
2019-04-23 21:12 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 14/63] Documentation: ACPI: move dsd/graph.txt " Changbin Du
2019-04-23 21:14 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 15/63] Documentation: ACPI: move dsd/data-node-references.txt " Changbin Du
2019-04-23 21:17 ` Mauro Carvalho Chehab
2019-04-24 16:44 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 16/63] Documentation: ACPI: move debug.txt " Changbin Du
2019-04-23 21:21 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 17/63] Documentation: ACPI: move method-tracing.txt to firmware-guide/acpi and convert to rsST Changbin Du
2019-04-24 14:26 ` Mauro Carvalho Chehab
2019-04-24 16:55 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 18/63] Documentation: ACPI: move aml-debugger.txt to firmware-guide/acpi and convert to reST Changbin Du
2019-04-24 14:28 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 19/63] Documentation: ACPI: move apei/output_format.txt " Changbin Du
2019-04-24 14:29 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 20/63] Documentation: ACPI: move apei/einj.txt " Changbin Du
2019-04-24 14:33 ` Mauro Carvalho Chehab
2019-04-24 17:12 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 21/63] Documentation: ACPI: move cppc_sysfs.txt to admin-guide/acpi " Changbin Du
2019-04-24 14:48 ` Mauro Carvalho Chehab
2019-04-24 17:22 ` Changbin Du
2019-04-24 18:04 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 22/63] Documentation: ACPI: move lpit.txt to firmware-guide/acpi " Changbin Du
2019-04-24 14:49 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 23/63] Documentation: ACPI: move ssdt-overlays.txt to admin-guide/acpi " Changbin Du
2019-04-24 14:51 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 24/63] Documentation: ACPI: move video_extension.txt to firmware-guide/acpi " Changbin Du
2019-04-24 14:56 ` Mauro Carvalho Chehab
2019-04-24 17:31 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 25/63] Documentation: add Linux PCI to Sphinx TOC tree Changbin Du
2019-04-24 15:03 ` Mauro Carvalho Chehab
2019-04-25 15:42 ` Changbin Du
2019-04-23 16:28 ` [PATCH v4 26/63] Documentation: PCI: convert pci.txt to reST Changbin Du
2019-04-24 15:20 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 27/63] Documentation: PCI: convert PCIEBUS-HOWTO.txt " Changbin Du
2019-04-24 15:23 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 28/63] Documentation: PCI: convert pci-iov-howto.txt " Changbin Du
2019-04-24 15:25 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 29/63] Documentation: PCI: convert MSI-HOWTO.txt " Changbin Du
2019-04-24 15:29 ` Mauro Carvalho Chehab
2019-04-23 16:28 ` [PATCH v4 30/63] Documentation: PCI: convert acpi-info.txt " Changbin Du
2019-04-24 15:34 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 31/63] Documentation: PCI: convert pci-error-recovery.txt " Changbin Du
2019-04-24 15:45 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 32/63] Documentation: PCI: convert pcieaer-howto.txt " Changbin Du
2019-04-24 15:49 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 33/63] Documentation: PCI: convert endpoint/pci-endpoint.txt " Changbin Du
2019-04-24 15:55 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 34/63] Documentation: PCI: convert endpoint/pci-endpoint-cfs.txt " Changbin Du
2019-04-24 16:26 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 35/63] Documentation: PCI: convert endpoint/pci-test-function.txt " Changbin Du
2019-04-24 16:58 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 36/63] Documentation: PCI: convert endpoint/pci-test-howto.txt " Changbin Du
2019-04-24 17:00 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 37/63] Documentation: add Linux x86 docs to Sphinx TOC tree Changbin Du
2019-04-24 17:04 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 38/63] Documentation: x86: convert boot.txt to reST Changbin Du
2019-04-24 17:36 ` Mauro Carvalho Chehab
2019-04-23 16:29 ` [PATCH v4 39/63] Documentation: x86: convert topology.txt " Changbin Du
2019-04-24 17:44 ` Mauro Carvalho Chehab
2019-04-26 14:23 ` Changbin Du
2019-04-23 16:29 ` [PATCH v4 40/63] Documentation: x86: convert exception-tables.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 41/63] Documentation: x86: convert kernel-stacks " Changbin Du
2019-04-23 16:29 ` [PATCH v4 42/63] Documentation: x86: convert entry_64.txt " Changbin Du
2019-04-23 16:29 ` Changbin Du [this message]
2019-04-23 16:29 ` [PATCH v4 44/63] Documentation: x86: convert zero-page.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 45/63] Documentation: x86: convert tlb.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 46/63] Documentation: x86: convert mtrr.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 47/63] Documentation: x86: convert pat.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 48/63] Documentation: x86: convert protection-keys.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 49/63] Documentation: x86: convert intel_mpx.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 50/63] Documentation: x86: convert amd-memory-encryption.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 51/63] Documentation: x86: convert pti.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 52/63] Documentation: x86: convert microcode.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 53/63] Documentation: x86: convert resctrl_ui.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 54/63] Documentation: x86: convert orc-unwinder.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 55/63] Documentation: x86: convert usb-legacy-support.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 56/63] Documentation: x86: convert i386/IO-APIC.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 57/63] Documentation: x86: convert x86_64/boot-options.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 58/63] Documentation: x86: convert x86_64/uefi.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 59/63] Documentation: x86: convert x86_64/mm.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 60/63] Documentation: x86: convert x86_64/5level-paging.txt " Changbin Du
2019-04-23 16:29 ` [PATCH v4 61/63] Documentation: x86: convert x86_64/fake-numa-for-cpusets " Changbin Du
2019-04-23 16:29 ` [PATCH v4 62/63] Documentation: x86: convert x86_64/cpu-hotplug-spec " Changbin Du
2019-04-23 16:29 ` [PATCH v4 63/63] Documentation: x86: convert x86_64/machinecheck " Changbin Du
2019-04-23 16:39 ` [PATCH v4 00/63] Include linux ACPI/PCI/X86 docs into Sphinx TOC tree Rafael J. Wysocki
2019-04-23 17:36 ` Bjorn Helgaas
2019-04-24 15:46 ` Changbin Du
2019-04-24 17:48 ` Mauro Carvalho Chehab
2019-04-24 16:18 ` Jonathan Corbet
2019-04-24 16:52 ` Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190423162932.21428-44-changbin.du@gmail.com \
--to=changbin.du@gmail.com \
--cc=bhelgaas@google.com \
--cc=corbet@lwn.net \
--cc=fenghua.yu@intel.com \
--cc=linux-acpi@vger.kernel.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linuxppc-dev@lists.ozlabs.org \
--cc=mchehab+samsung@kernel.org \
--cc=mingo@redhat.com \
--cc=rjw@rjwysocki.net \
--cc=tglx@linutronix.de \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).