[PATCH v5 00/11] Add BananaPi R3

[PATCH v5 00/11] Add BananaPi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

This Series adds some Nodes to mt7986 devicetree and the BananaPi R3

This version is rebased on Matthias' DTS64 next Branch from 2022/11/11.

i included sams series for mt7986 DTS with small changes
https://patchwork.kernel.org/project/linux-mediatek/cover/20220427124741.18245->

6.2 will support dtso extension for dt overlays:

"kbuild: Allow DTB overlays to built from .dtso named source files"
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2

There is some discussion about inclusion of dt-overlays and if it is
better to support mmc also by these:

https://patchwork.kernel.org/comment/25092116/
https://patchwork.kernel.org/comment/25085681/

i had run full dtbs-check but i end up with some strange warnings in
ethernet-node that should not come up as phy-handle and sfp/managed
properties are already defined.

phy-handle made optional
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documen>

property sfp/managed (which is included for mac subnode in yaml above):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documen>

changes:
v5:
- changed usb ranges/reg/unit-adress
- added reviewd-by's except usb-part due to changes

v4:
- dropped RFC prefix
- rebase on matthias' mtk dts-next (for 6.2) branch
- added author information to overlays
- fixed sfp binding error
- added fix for moving wed_pcie node
- readded missing compatible patches

v3:
- changed mmc pull-ups
- added patch for board binding (sent separately before)
- added pcie node in mt7986 (not yet again in r3)
- added dt overlays





Frank Wunderlich (7):
  arm64: dts: mt7986: move wed_pcie node
  dt-bindings: phy: mediatek,tphy: add support for mt7986
  dt-bindings: usb: mtk-xhci: add support for mt7986
  dt-bindings: PCI: mediatek-gen3: add SoC based clock config
  dt-bindings: PCI: mediatek-gen3: add support for mt7986
  arm64: dts: mt7986: add Bananapi R3
  arm64: dts: mt7986: add BPI-R3 nand/nor overlays

Sam Shih (4):
  arm64: dts: mt7986: add spi related device nodes
  arm64: dts: mt7986: add usb related device nodes
  arm64: dts: mt7986: add mmc related device nodes
  arm64: dts: mt7986: add pcie related device nodes

 .../bindings/pci/mediatek-pcie-gen3.yaml      |  64 ++-
 .../bindings/phy/mediatek,tphy.yaml           |   1 +
 .../bindings/usb/mediatek,mtk-xhci.yaml       |   1 +
 arch/arm64/boot/dts/mediatek/Makefile         |   4 +
 .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts |  31 ++
 .../mediatek/mt7986a-bananapi-bpi-r3-nand.dts |  55 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dts  |  69 +++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts   |  25 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts  | 166 +++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     | 162 ++++++-
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts  |  63 +++
 12 files changed, 1081 insertions(+), 18 deletions(-)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi

-- 
2.34.1

[PATCH v5 01/11] arm64: dts: mt7986: move wed_pcie node

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Move the wed_pcie node to have node aligned by address.

Fixes: 00b9903996b3 ("arm64: dts: mediatek: mt7986: add support for Wireless Ethernet Dispatch")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index a22e10e89ab9..afc01abfa99c 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -112,6 +112,12 @@ infracfg: infracfg@10001000 {
 			#clock-cells = <1>;
 		};
 
+		wed_pcie: wed-pcie@10003000 {
+			compatible = "mediatek,mt7986-wed-pcie",
+				     "syscon";
+			reg = <0 0x10003000 0 0x10>;
+		};
+
 		topckgen: topckgen@1001b000 {
 			compatible = "mediatek,mt7986-topckgen", "syscon";
 			reg = <0 0x1001B000 0 0x1000>;
@@ -257,12 +263,6 @@ ethsys: syscon@15000000 {
 			 #reset-cells = <1>;
 		};
 
-		wed_pcie: wed-pcie@10003000 {
-			compatible = "mediatek,mt7986-wed-pcie",
-				     "syscon";
-			reg = <0 0x10003000 0 0x10>;
-		};
-
 		wed0: wed@15010000 {
 			compatible = "mediatek,mt7986-wed",
 				     "syscon";
-- 
2.34.1

[PATCH v5 02/11] dt-bindings: phy: mediatek,tphy: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
index 5613cc5106e3..230a17f24966 100644
--- a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
+++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml
@@ -79,6 +79,7 @@ properties:
           - enum:
               - mediatek,mt2712-tphy
               - mediatek,mt7629-tphy
+              - mediatek,mt7986-tphy
               - mediatek,mt8183-tphy
               - mediatek,mt8186-tphy
               - mediatek,mt8192-tphy
-- 
2.34.1

[PATCH v5 03/11] dt-bindings: usb: mtk-xhci: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string for mt7986.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
index 939623867a64..a3c37944c630 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
@@ -28,6 +28,7 @@ properties:
           - mediatek,mt7622-xhci
           - mediatek,mt7623-xhci
           - mediatek,mt7629-xhci
+          - mediatek,mt7986-xhci
           - mediatek,mt8173-xhci
           - mediatek,mt8183-xhci
           - mediatek,mt8186-xhci
-- 
2.34.1

[PATCH v5 04/11] dt-bindings: PCI: mediatek-gen3: add SoC based clock config

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

The PCIe driver covers different SOC which needing different clock
configs. Define them based on compatible.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
v2:
- fix typo in mediatek,mt8192-pcie
v3:
- remove contains to match only if compatible is no fallback
  tested with series "Add driver nodes for MT8195 SoC" and mt7986
  pcie-nodes, dtbs_check is now clean
---
 .../bindings/pci/mediatek-pcie-gen3.yaml      | 47 ++++++++++++++-----
 1 file changed, 35 insertions(+), 12 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
index c00be39af64e..5d7369debff2 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
@@ -43,9 +43,6 @@ description: |+
   each set has its own address for MSI message, and supports 32 MSI vectors
   to generate interrupt.
 
-allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
-
 properties:
   compatible:
     oneOf:
@@ -84,15 +81,7 @@ properties:
     maxItems: 6
 
   clock-names:
-    items:
-      - const: pl_250m
-      - const: tl_26m
-      - const: tl_96m
-      - const: tl_32k
-      - const: peri_26m
-      - enum:
-          - top_133m        # for MT8192
-          - peri_mem        # for MT8188/MT8195
+    maxItems: 6
 
   assigned-clocks:
     maxItems: 1
@@ -138,6 +127,40 @@ required:
   - '#interrupt-cells'
   - interrupt-controller
 
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+  - if:
+      properties:
+        compatible:
+          const: mediatek,mt8192-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: tl_96m
+            - const: tl_32k
+            - const: peri_26m
+            - const: top_133m
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt8188-pcie
+              - mediatek,mt8195-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: tl_96m
+            - const: tl_32k
+            - const: peri_26m
+            - const: peri_mem
+
 unevaluatedProperties: false
 
 examples:
-- 
2.34.1

[PATCH v5 05/11] dt-bindings: PCI: mediatek-gen3: add support for mt7986

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add compatible string and clock-definition for mt7986. It needs 4 clocks
for PCIe, define them in binding.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jianjun Wang <jianjun.wang@mediatek.com>
---
v2:
- squashed patch 2+3 (compatible and clock definition)
---
 .../bindings/pci/mediatek-pcie-gen3.yaml        | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
index 5d7369debff2..f7a02019daea 100644
--- a/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
+++ b/Documentation/devicetree/bindings/pci/mediatek-pcie-gen3.yaml
@@ -48,6 +48,7 @@ properties:
     oneOf:
       - items:
           - enum:
+              - mediatek,mt7986-pcie
               - mediatek,mt8188-pcie
               - mediatek,mt8195-pcie
           - const: mediatek,mt8192-pcie
@@ -78,9 +79,11 @@ properties:
       - const: mac
 
   clocks:
+    minItems: 4
     maxItems: 6
 
   clock-names:
+    minItems: 4
     maxItems: 6
 
   assigned-clocks:
@@ -160,6 +163,20 @@ allOf:
             - const: tl_32k
             - const: peri_26m
             - const: peri_mem
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt7986-pcie
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: pl_250m
+            - const: tl_26m
+            - const: peri_26m
+            - const: top_133m
 
 unevaluatedProperties: false
 
-- 
2.34.1

[PATCH v5 06/11] arm64: dts: mt7986: add spi related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds spi support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 35 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 28 ++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 35 ++++++++++++++++++++
 3 files changed, 98 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 2f48cc3d3ddb..006878e3f2b2 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -59,6 +59,20 @@ switch: switch@0 {
 };
 
 &pio {
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_2";
+		};
+	};
+
 	uart1_pins: uart1-pins {
 		mux {
 			function = "uart";
@@ -105,6 +119,27 @@ conf {
 	};
 };
 
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+	spi_nand: spi_nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		spi-tx-buswidth = <4>;
+		spi-rx-buswidth = <4>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index afc01abfa99c..29da9b8ed753 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -253,6 +253,34 @@ i2c0: i2c@11008000 {
 			status = "disabled";
 		};
 
+		spi0: spi@1100a000 {
+			compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100a000 0 0x100>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_MPLL_D2>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI0_CK>,
+				 <&infracfg CLK_INFRA_SPI0_HCK_CK>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+			status = "disabled";
+		};
+
+		spi1: spi@1100b000 {
+			compatible = "mediatek,mt7986-spi-ipm", "mediatek,spi-ipm";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100b000 0 0x100>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_MPLL_D2>,
+				 <&topckgen CLK_TOP_SPIM_MST_SEL>,
+				 <&infracfg CLK_INFRA_SPI1_CK>,
+				 <&infracfg CLK_INFRA_SPI1_HCK_CK>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk", "hclk";
+			status = "disabled";
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 79c5c78f7a14..2c7f1d4fb352 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -100,6 +100,20 @@ fixed-link {
 };
 
 &pio {
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_2";
+		};
+	};
+
 	wf_2g_5g_pins: wf-2g-5g-pins {
 		mux {
 			function = "wifi";
@@ -132,6 +146,27 @@ conf {
 	};
 };
 
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+	spi_nand: spi_nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		spi-tx-buswidth = <4>;
+		spi-rx-buswidth = <4>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
-- 
2.34.1

[PATCH v5 07/11] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds USB support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
changes compared to sams original version:
- reorder xhci-clocks based on yaml binding

v5:
 - update ranges/reg of usb-phy
 - not added RB from AngeloGioacchino for v4 because of these changes
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 28 ++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 28 ++++++++++
 3 files changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 006878e3f2b2..2b5d7ea31b4d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -23,6 +23,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -140,6 +158,12 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
 &switch {
 	ports {
 		#address-cells = <1>;
@@ -201,6 +225,10 @@ &uart2 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index 29da9b8ed753..c69b8bff7f4a 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -281,6 +281,61 @@ spi1: spi@1100b000 {
 			status = "disabled";
 		};
 
+		ssusb: usb@11200000 {
+			compatible = "mediatek,mt7986-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x2e00>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+				 <&infracfg CLK_INFRA_IUSB_CK>,
+				 <&infracfg CLK_INFRA_IUSB_133_CK>,
+				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
+				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+			clock-names = "sys_ck",
+				      "ref_ck",
+				      "mcu_ck",
+				      "dma_ck",
+				      "xhci_ck";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>,
+			       <&u2port1 PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		usb_phy: t-phy@11e10000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e10000 0x1700>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&topckgen CLK_TOP_USB3_PHY_SEL>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u2port1: usb-phy@1000 {
+				reg = <0x1000 0x700>;
+				clocks = <&topckgen CLK_TOP_DA_U2_REFSEL>,
+					 <&topckgen CLK_TOP_DA_U2_CK_1P_SEL>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		ethsys: syscon@15000000 {
 			 #address-cells = <1>;
 			 #size-cells = <1>;
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
index 2c7f1d4fb352..a98025112b5a 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -23,6 +23,24 @@ memory@40000000 {
 		device_type = "memory";
 		reg = <0 0x40000000 0 0x40000000>;
 	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &crypto {
@@ -167,10 +185,20 @@ &spi1 {
 	status = "okay";
 };
 
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb_phy {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	pinctrl-names = "default", "dbdc";
-- 
2.34.1

[PATCH v5 08/11] arm64: dts: mt7986: add mmc related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds mmc support for MT7986.

Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
v3:
- fix pullups/pulldowns for mt7986a-rfb to have generic bias-pull-*

v2:
- update mmc-node because clocks changed
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 87 ++++++++++++++++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 15 ++++
 2 files changed, 102 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index 2b5d7ea31b4d..e1a0331aaa5f 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -5,6 +5,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/pinctrl/mt65xx.h>
+
 #include "mt7986a.dtsi"
 
 / {
@@ -24,6 +26,15 @@ memory@40000000 {
 		reg = <0 0x40000000 0 0x40000000>;
 	};
 
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
@@ -76,7 +87,83 @@ switch: switch@0 {
 	};
 };
 
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &pio {
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index c69b8bff7f4a..b3ad8978b563 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -304,6 +304,21 @@ ssusb: usb@11200000 {
 			status = "disabled";
 		};
 
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt7986-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11c20000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&topckgen CLK_TOP_EMMC_416M_SEL>,
+				 <&infracfg CLK_INFRA_MSDC_HCK_CK>,
+				 <&infracfg CLK_INFRA_MSDC_CK>,
+				 <&infracfg CLK_INFRA_MSDC_133M_CK>,
+				 <&infracfg CLK_INFRA_MSDC_66M_CK>;
+			clock-names = "source", "hclk", "source_cg", "bus_clk",
+				      "sys_cg";
+			status = "disabled";
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v5 09/11] arm64: dts: mt7986: add pcie related device nodes

[Frank Wunderlich]

From: Sam Shih <sam.shih@mediatek.com>

This patch adds PCIe support for MT7986.

Signed-off-by: Jieyy Yang <jieyy.yang@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
changes compared to sams original version:

- add clock-names to pcie node
- update clocks to new binding
---
bindings-patches:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=690172
---
 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 16 ++++++
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 52 ++++++++++++++++++++
 2 files changed, 68 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
index e1a0331aaa5f..01fa08c57c39 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -102,6 +102,15 @@ &mmc0 {
 	non-removable;
 	no-sd;
 	no-sdio;
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
 	status = "okay";
 };
 
@@ -164,6 +173,13 @@ conf-rst {
 		};
 	};
 
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+		};
+	};
+
 	spi_flash_pins: spi-flash-pins {
 		mux {
 			function = "spi";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
index b3ad8978b563..b310abc02dcc 100644
--- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/mt7986-clk.h>
 #include <dt-bindings/reset/mt7986-resets.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -319,6 +320,57 @@ mmc0: mmc@11230000 {
 			status = "disabled";
 		};
 
+		pcie: pcie@11280000 {
+			compatible = "mediatek,mt7986-pcie",
+				     "mediatek,mt8192-pcie";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			reg = <0x00 0x11280000 0x00 0x4000>;
+			reg-names = "pcie-mac";
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0x00 0x20000000 0x00
+				  0x20000000 0x00 0x10000000>;
+			clocks = <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+				 <&infracfg CLK_INFRA_IPCIE_CK>,
+				 <&infracfg CLK_INFRA_IPCIER_CK>,
+				 <&infracfg CLK_INFRA_IPCIEB_CK>;
+			clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+			status = "disabled";
+
+			phys = <&pcie_port PHY_TYPE_PCIE>;
+			phy-names = "pcie-phy";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &pcie_intc 0>,
+					<0 0 0 2 &pcie_intc 1>,
+					<0 0 0 3 &pcie_intc 2>,
+					<0 0 0 4 &pcie_intc 3>;
+			pcie_intc: interrupt-controller {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				interrupt-controller;
+			};
+		};
+
+		pcie_phy: t-phy@11c00000 {
+			compatible = "mediatek,mt7986-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			pcie_port: pcie-phy@11c00000 {
+				reg = <0 0x11c00000 0 0x20000>;
+				clocks = <&clk40m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
 		usb_phy: t-phy@11e10000 {
 			compatible = "mediatek,mt7986-tphy",
 				     "mediatek,generic-tphy-v2";
-- 
2.34.1

[PATCH v5 10/11] arm64: dts: mt7986: add Bananapi R3

[Frank Wunderlich]

From: Frank Wunderlich <frank-w@public-files.de>

Add support for Bananapi R3 SBC.

- SD/eMMC support (switching first 4 bits of data-bus with sw6/D)
- all rj45 ports and both SFP working (eth1/lan4)
- all USB-Ports + SIM-Slot tested
- i2c and all uarts tested
- wifi tested (with eeprom calibration data)

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---

The device can boot from all 4 storage options. Both, SPI and MMC, can
be switched using hardware switches on the board, see
https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting

I have added base dtb for sd/emmc to have a bootable version in mainline
linux. SPI-NAND/NOR switched (CS by sw5/C) can be done with DT-Overlays,
but don't know how to do it in upstream the right way...added dts files
for dtbo and added them with dtbo extension to Makefile works.

there is a commit which adds support building dtso files to dtbo in next:

"kbuild: Allow DTB overlays to built from .dtso named source files"
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2

if Overlays are accepted then we can change my current dts from here
to overlays too to have all as such. Till then imho the best way is to
have mmc as board dts and add the right spi-device via overlay if
needed.

changes:
v4:
- add PCIe nodes
- fix sfp-properties of sfp-1 (need to be plural)
  thx to Denis Odintsov for this

v3:
- rename factory-key to reset-key
- add dcin regulator and add it as input for 3v3 (with renaming)
- remove memory-node
- dropped wifi eeprom (calibration) data
- move mmc0 pinctrl to common dtsi and drop sdcard comment
- change mmc pull-up/down to have generic bias-pull*

v2:
- remove pcie to be added later (discussion about clocks)
- some fixes based on suggestions on ML
  - add key suffix like it's done in mt7622-bpi-r64 devicetree
  - add dash in sfp node names
  - use reg as unit for switch-node
  - drop "-3-4" suffix from i2c-pins node name
  - fix order in Makefile
---
 arch/arm64/boot/dts/mediatek/Makefile         |   2 +
 .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts |  31 ++
 .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts   |  25 +
 .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 458 ++++++++++++++++++
 4 files changed, 516 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 0ec90cb3ef28..e8902f2cc58f 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
new file mode 100644
index 000000000000..a0ca35b5977e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3 (emmc)";
+};
+
+&mmc0 {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	hs400-ds-delay = <0x14014>;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
new file mode 100644
index 000000000000..06e4691cb815
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#include "mt7986a-bananapi-bpi-r3.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3 (sdmmc)";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	max-frequency = <52000000>;
+	cap-sd-highspeed;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
new file mode 100644
index 000000000000..def16e36f1e6
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Sam.Shih <sam.shih@mediatek.com>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ *          Daniel Golle <daniel@makrotopia.org>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "Bananapi BPI-R3";
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	dcin: regulator-12vd {
+		compatible = "regulator-fixed";
+		regulator-name = "12vd";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset-key {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps-key {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* i2c of the left SFP cage (wan) */
+	i2c_sfp1: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	/* i2c of the right SFP cage (lan) */
+	i2c_sfp2: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		blue_led: led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 86 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1.8vd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3vd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name  = "fixed-5p1";
+		regulator-min-microvolt = <5100000>;
+		regulator-max-microvolt = <5100000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&dcin>;
+	};
+
+	/* left SFP cage (wan) */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* right SFP cage (lan) */
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		sfp = <&sfp1>;
+		managed = "in-band-status";
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@31 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_pins>;
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pio {
+	i2c_pins: i2c-pins {
+		mux {
+			function = "i2c";
+			groups = "i2c";
+		};
+	};
+
+	mmc0_pins_default: mmc0-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		mux {
+			function = "emmc";
+			groups = "emmc_51";
+		};
+		conf-cmd-dat {
+			pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+			       "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+			       "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+			input-enable;
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+		conf-clk {
+			pins = "EMMC_CK";
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-ds {
+			pins = "EMMC_DSL";
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+		};
+		conf-rst {
+			pins = "EMMC_RSTB";
+			drive-strength = <4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+		};
+	};
+
+	pcie_pins: pcie-pins {
+		mux {
+			function = "pcie";
+			groups = "pcie_clk", "pcie_pereset";
+		};
+	};
+
+	spi_flash_pins: spi-flash-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spic_pins: spic-pins {
+		mux {
+			function = "spi";
+			groups = "spi1_0";
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1_rx_tx";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2_0_rx_tx";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_led_pins: wf-led-pins {
+		mux {
+			function = "led";
+			groups = "wifi_led";
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spic_pins>;
+	cs-gpios = <0>, <0>;
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "wan";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan0";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan3";
+		};
+
+		port5: port@5 {
+			reg = <5>;
+			label = "lan4";
+			phy-mode = "2500base-x";
+			sfp = <&sfp2>;
+			managed = "in-band-status";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+};
+
-- 
2.34.1

Re: [PATCH v5 07/11] arm64: dts: mt7986: add usb related device nodes

[Chunfeng Yun (云春峰)]

On Thu, 2022-11-17 at 17:27 +0100, Frank Wunderlich wrote:
> From: Sam Shih <sam.shih@mediatek.com>
> 
> This patch adds USB support for MT7986.
> 
> Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> changes compared to sams original version:
> - reorder xhci-clocks based on yaml binding
> 
> v5:
>  - update ranges/reg of usb-phy
>  - not added RB from AngeloGioacchino for v4 because of these changes
> ---
>  arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 28 ++++++++++
>  arch/arm64/boot/dts/mediatek/mt7986a.dtsi    | 55
> ++++++++++++++++++++
>  arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts | 28 ++++++++++
>  3 files changed, 111 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> index 006878e3f2b2..2b5d7ea31b4d 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> @@ -23,6 +23,24 @@ memory@40000000 {
>  		device_type = "memory";
>  		reg = <0 0x40000000 0 0x40000000>;
>  	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_5v: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };
Usually if we use a gpio to control a switch to turn on/off power, we
model it as a fixed regulator, but here no gpio provided in reg_3p3v
and reg_5v, if no gpio used, no need these two fixed regulators too.

>  
>  &crypto {
> @@ -140,6 +158,12 @@ &spi1 {
>  	status = "okay";
>  };
>  
> +&ssusb {
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&reg_5v>;
These two supply can be removed if no swith to control them, they are
optional.

> +	status = "okay";
> +};
> +
>  &switch {
>  	ports {
>  		#address-cells = <1>;
> @@ -201,6 +225,10 @@ &uart2 {
>  	status = "okay";
>  };
>  
> +&usb_phy {
> +	status = "okay";
> +};
> +
>  &wifi {
>  	status = "okay";
>  	pinctrl-names = "default", "dbdc";
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> index 29da9b8ed753..c69b8bff7f4a 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> @@ -281,6 +281,61 @@ spi1: spi@1100b000 {
>  			status = "disabled";
>  		};
>  
> +		ssusb: usb@11200000 {
> +			compatible = "mediatek,mt7986-xhci",
> +				     "mediatek,mtk-xhci";
> +			reg = <0 0x11200000 0 0x2e00>,
> +			      <0 0x11203e00 0 0x0100>;
> +			reg-names = "mac", "ippc";
> +			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_133_CK>,
> +				 <&infracfg CLK_INFRA_IUSB_66M_CK>,
> +				 <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
> +			clock-names = "sys_ck",
> +				      "ref_ck",
> +				      "mcu_ck",
> +				      "dma_ck",
> +				      "xhci_ck";
> +			phys = <&u2port0 PHY_TYPE_USB2>,
> +			       <&u3port0 PHY_TYPE_USB3>,
> +			       <&u2port1 PHY_TYPE_USB2>;
> +			status = "disabled";
> +		};
> +
> +		usb_phy: t-phy@11e10000 {
> +			compatible = "mediatek,mt7986-tphy",
> +				     "mediatek,generic-tphy-v2";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0 0 0x11e10000 0x1700>;
> +			status = "disabled";
> +
> +			u2port0: usb-phy@0 {
> +				reg = <0x0 0x700>;
> +				clocks = <&topckgen
> CLK_TOP_DA_U2_REFSEL>,
> +					 <&topckgen
> CLK_TOP_DA_U2_CK_1P_SEL>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u3port0: usb-phy@700 {
> +				reg = <0x700 0x900>;
> +				clocks = <&topckgen
> CLK_TOP_USB3_PHY_SEL>;
> +				clock-names = "ref";
> +				#phy-cells = <1>;
> +			};
> +
> +			u2port1: usb-phy@1000 {
> +				reg = <0x1000 0x700>;
> +				clocks = <&topckgen
> CLK_TOP_DA_U2_REFSEL>,
> +					 <&topckgen
> CLK_TOP_DA_U2_CK_1P_SEL>;
> +				clock-names = "ref", "da_ref";
> +				#phy-cells = <1>;
> +			};
> +		};
> +
>  		ethsys: syscon@15000000 {
>  			 #address-cells = <1>;
>  			 #size-cells = <1>;
> diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> index 2c7f1d4fb352..a98025112b5a 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
> @@ -23,6 +23,24 @@ memory@40000000 {
>  		device_type = "memory";
>  		reg = <0 0x40000000 0 0x40000000>;
>  	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
> +
> +	reg_5v: regulator-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
ditto
> +	};
>  };
>  
>  &crypto {
> @@ -167,10 +185,20 @@ &spi1 {
>  	status = "okay";
>  };
>  
> +&ssusb {
> +	vusb33-supply = <&reg_3p3v>;
> +	vbus-supply = <&reg_5v>;
ditto

> +	status = "okay";
> +};
> +
>  &uart0 {
>  	status = "okay";
>  };
>  
> +&usb_phy {
> +	status = "okay";
> +};
> +
>  &wifi {
>  	status = "okay";
>  	pinctrl-names = "default", "dbdc";

Aw: Re: [PATCH v5 07/11] arm64: dts: mt7986: add usb related device nodes

[Frank Wunderlich]

Hi

> Gesendet: Freitag, 18. November 2022 um 07:43 Uhr
> Von: "Chunfeng Yun (云春峰)" <Chunfeng.Yun@mediatek.com>
> On Thu, 2022-11-17 at 17:27 +0100, Frank Wunderlich wrote:
> > From: Sam Shih <sam.shih@mediatek.com>
> > 
> > This patch adds USB support for MT7986.
> > 
> > Signed-off-by: Sam Shih <sam.shih@mediatek.com>
> > Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> > ---
> > changes compared to sams original version:
> > - reorder xhci-clocks based on yaml binding
> > 
> > v5:
> >  - update ranges/reg of usb-phy
> >  - not added RB from AngeloGioacchino for v4 because of these changes

> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > index 006878e3f2b2..2b5d7ea31b4d 100644
> > --- a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > @@ -23,6 +23,24 @@ memory@40000000 {
> >  		device_type = "memory";
> >  		reg = <0 0x40000000 0 0x40000000>;
> >  	};
> > +
> > +	reg_3p3v: regulator-3p3v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "fixed-3.3V";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-boot-on;
> > +		regulator-always-on;
> > +	};
> > +
> > +	reg_5v: regulator-5v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "fixed-5V";
> > +		regulator-min-microvolt = <5000000>;
> > +		regulator-max-microvolt = <5000000>;
> > +		regulator-boot-on;
> > +		regulator-always-on;
> > +	};
> >  };
> Usually if we use a gpio to control a switch to turn on/off power, we
> model it as a fixed regulator, but here no gpio provided in reg_3p3v
> and reg_5v, if no gpio used, no need these two fixed regulators too.

i can drop 5v regulator, but 3v3 is used by emmc, so i would move that to the mmc-patch

> >  
> >  &crypto {
> > @@ -140,6 +158,12 @@ &spi1 {
> >  	status = "okay";
> >  };
> >  
> > +&ssusb {
> > +	vusb33-supply = <&reg_3p3v>;
> > +	vbus-supply = <&reg_5v>;
> These two supply can be removed if no swith to control them, they are
> optional.

ok, i drop the references.

anything else ok?

prepared patch here (now yet squashed):
https://github.com/frank-w/BPI-R2-4.14/commits/6.1-r3dts

regards Frank