linux-pci.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Zhou Wang <wangzhou1@hisilicon.com>
To: James Morse <james.morse@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>,
	Jingoo Han <jg1.han@samsung.com>,
	Pratyush Anand <pratyush.anand@gmail.com>,
	Arnd Bergmann <arnd@arndb.de>,
	"fabrice.gasnier@st.com" <fabrice.gasnier@st.com>,
	Liviu Dudau <Liviu.Dudau@arm.com>,
	"linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>,
	"linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	"gabriele.paoloni@huawei.com" <gabriele.paoloni@huawei.com>,
	"yuanzhichang@hisilicon.com" <yuanzhichang@hisilicon.com>,
	"zhudacai@hisilicon.com" <zhudacai@hisilicon.com>,
	"zhangjukuo@huawei.com" <zhangjukuo@huawei.com>,
	"qiuzhenfa@hisilicon.com" <qiuzhenfa@hisilicon.com>,
	"liguozhu@hisilicon.com" <liguozhu@hisilicon.com>
Subject: Re: [PATCH v2 2/4] PCI: designware: Add ARM64 support
Date: Fri, 5 Jun 2015 16:11:30 +0800	[thread overview]
Message-ID: <557159B2.9090103@hisilicon.com> (raw)
In-Reply-To: <5570507F.4030704@arm.com>

On 2015/6/4 21:19, James Morse wrote:
> On 03/06/15 09:35, Zhou Wang wrote:
>> This patch tries to unify ARM32 and ARM64 PCIe in designware driver. Delete
>> function dw_pcie_setup, dw_pcie_scan_bus, dw_pcie_map_irq and struct hw_pci,
>> move related operations to dw_pcie_host_init. Also set pp->root_bus_nr = 0 in
>> each PCIe host driver which is based on pcie-designware.
>>
>> I am not very clear about I/O resource management:
>>> 	if (global_io_offset < SZ_1M && pp->io_size > 0) {
>>> 		pci_ioremap_io(global_io_offset, pp->io_base);
>>> 		global_io_offset += SZ_64K;
>>> 		pci_add_resource_offset(&res, &pp->io,
>>> 					global_io_offset - pp->io_bus_addr);
>>> 	}
>> so just move steps in dw_pcie_setup to dw_pcie_host_init.
>>
>> I have compiled the driver with multi_v7_defconfig. However, I don't have
>> ARM32 PCIe related board to do test. It will be appreciated if someone could
>> help to test it.
> 
> I have tested this on a 'Freescale i.MX6 Quad SABRE Lite Board', which also
> uses a designware pcie host controller (PCI_IMX6). Booted,
> removed/rescanned the bus, then scanned for wireless access points using
> the b43 driver. Please note my change below.
> 
> Tested-by: James Morse <james.morse@arm.com>
> 

Hi James,

Many thanks for your help to test :)

>> diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c
>> index 2e9f84f..b3f0ac7 100644
>> --- a/drivers/pci/host/pcie-designware.c
>> +++ b/drivers/pci/host/pcie-designware.c
>> @@ -11,6 +11,7 @@
>>   * published by the Free Software Foundation.
>>   */
>>  
>> +#include <linux/hardirq.h>
>>  #include <linux/irq.h>
>>  #include <linux/irqdomain.h>
>>  #include <linux/kernel.h>
>> @@ -67,17 +68,10 @@
>>  #define PCIE_ATU_FUNC(x)		(((x) & 0x7) << 16)
>>  #define PCIE_ATU_UPPER_TARGET		0x91C
>>  
>> -static struct hw_pci dw_pci;
>> +static struct pci_ops dw_pcie_ops;
>>  
>>  static unsigned long global_io_offset;
>>  
>> -static inline struct pcie_port *sys_to_pcie(struct pci_sys_data *sys)
>> -{
>> -	BUG_ON(!sys->private_data);
>> -
>> -	return sys->private_data;
>> -}
>> -
>>  int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
>>  {
>>  	*val = readl(addr);
>> @@ -238,7 +232,7 @@ static void dw_pcie_msi_set_irq(struct pcie_port *pp, int irq)
>>  static int assign_irq(int no_irqs, struct msi_desc *desc, int *pos)
>>  {
>>  	int irq, pos0, i;
>> -	struct pcie_port *pp = sys_to_pcie(desc->dev->bus->sysdata);
>> +	struct pcie_port *pp = desc->dev->bus->sysdata;
>>  
>>  	pos0 = bitmap_find_free_region(pp->msi_irq_in_use, MAX_MSI_IRQS,
>>  				       order_base_2(no_irqs));
>> @@ -281,7 +275,7 @@ static int dw_msi_setup_irq(struct msi_controller *chip, struct pci_dev *pdev,
>>  {
>>  	int irq, pos;
>>  	struct msi_msg msg;
>> -	struct pcie_port *pp = sys_to_pcie(pdev->bus->sysdata);
>> +	struct pcie_port *pp = pdev->bus->sysdata;
>>  
>>  	if (desc->msi_attrib.is_msix)
>>  		return -EINVAL;
>> @@ -310,7 +304,7 @@ static void dw_msi_teardown_irq(struct msi_controller *chip, unsigned int irq)
>>  {
>>  	struct irq_data *data = irq_get_irq_data(irq);
>>  	struct msi_desc *msi = irq_data_get_msi(data);
>> -	struct pcie_port *pp = sys_to_pcie(msi->dev->bus->sysdata);
>> +	struct pcie_port *pp = msi->dev->bus->sysdata;
>>  
>>  	clear_irq_range(pp, irq, 1, data->hwirq);
>>  }
>> @@ -342,13 +336,15 @@ static const struct irq_domain_ops msi_domain_ops = {
>>  	.map = dw_pcie_msi_map,
>>  };
>>  
>> -int dw_pcie_host_init(struct pcie_port *pp)
>> +int __init dw_pcie_host_init(struct pcie_port *pp)
>>  {
>>  	struct device_node *np = pp->dev->of_node;
>>  	struct platform_device *pdev = to_platform_device(pp->dev);
>>  	struct of_pci_range range;
>>  	struct of_pci_range_parser parser;
>> +	struct pci_bus *bus;
>>  	struct resource *cfg_res;
>> +	LIST_HEAD(res);
>>  	u32 val, na, ns;
>>  	const __be32 *addrp;
>>  	int i, index, ret;
>> @@ -502,15 +498,49 @@ int dw_pcie_host_init(struct pcie_port *pp)
>>  	val |= PORT_LOGIC_SPEED_CHANGE;
>>  	dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
>>  
>> -#ifdef CONFIG_PCI_MSI
>> -	dw_pcie_msi_chip.dev = pp->dev;
>> -	dw_pci.msi_ctrl = &dw_pcie_msi_chip;
>> +#ifdef CONFIG_ARM
>> +	/*
>> +	 * FIXME: we should really be able to use
>> +	 * of_pci_get_host_bridge_resources on arm32 as well,
>> +	 * but the conversion needs some more testing
>> +	 */
>> +	if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> +		pci_ioremap_io(global_io_offset, pp->io_base);
>> +		global_io_offset += SZ_64K;
>> +		pci_add_resource_offset(&res, &pp->io,
>> +					global_io_offset - pp->io_bus_addr);
>> +	}
>> +	pci_add_resource_offset(&res, &pp->mem,
>> +				pp->mem.start - pp->mem_bus_addr);
>> +	pci_add_resource(&res, &pp->busn);
> 
> I don't think this #ifdef is necessary. In the spirit of 'the conversion
> needs some more testing', I removed it leaving just the below arm64 code.
> 
> This worked on my Freescale i.MX6 Quad SABRE Lite Board, I went as far as
> scanning for wireless access points.
> 

I think it depends on which kind of PCIe device you use, if we use a PCIe device
with a I/O Bar, it may not work well without above code. But so far, I have not
met a PCIe device which must work with a I/O Bar.

>> +#else
>> +	ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &pp->io_base);
> 
> of_pci_get_host_bridge_resources expects &pp->io_base to be a
> resource_size_t*, but &io_base is u64*. This generates a warning on arm
> with the above change. Changing the the type in
> drivers/pci/host/pcie-designware.h fixes this.
> 
> 
> Thanks,
> 
> James
> 

OK, will modify this in next version.

Best Regards and thanks again for your test,
Zhou

>> +	if (ret)
>> +		return ret;
>> +#endif
>> +
>> +	bus = pci_create_root_bus(pp->dev, pp->root_bus_nr, &dw_pcie_ops,
>> +			      pp, &res);
>> +	if (!bus)
>> +		return -ENOMEM;
>> +
>> +#ifdef CONFIG_GENERIC_MSI_IRQ_DOMAIN
>> +	bus->msi = container_of(&pp->irq_domain, struct msi_controller, domain);
>> +#else
>> +	bus->msi = &dw_pcie_msi_chip;
>>  #endif
>>  
>> -	dw_pci.nr_controllers = 1;
>> -	dw_pci.private_data = (void **)&pp;
>> +	pci_scan_child_bus(bus);
>> +	if (pp->ops->scan_bus)
>> +		pp->ops->scan_bus(pp);
>>  
>> -	pci_common_init_dev(pp->dev, &dw_pci);
>> +#ifdef CONFIG_ARM
>> +	/* support old dtbs that incorrectly describe IRQs */
>> +	pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
>> +#endif
>> +
>> +	pci_assign_unassigned_bus_resources(bus);
>> +	pci_bus_add_devices(bus);
>>  
>>  	return 0;
>>  }
>> @@ -653,7 +683,7 @@ static int dw_pcie_valid_config(struct pcie_port *pp,
>>  static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>>  			int size, u32 *val)
>>  {
>> -	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> +	struct pcie_port *pp = bus->sysdata;
>>  	int ret;
>>  
>>  	if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
>> @@ -677,7 +707,7 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
>>  static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
>>  			int where, int size, u32 val)
>>  {
>> -	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
>> +	struct pcie_port *pp = bus->sysdata;
>>  	int ret;
>>  
>>  	if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
>> @@ -701,64 +731,6 @@ static struct pci_ops dw_pcie_ops = {
>>  	.write = dw_pcie_wr_conf,
>>  };
>>  
>> -static int dw_pcie_setup(int nr, struct pci_sys_data *sys)
>> -{
>> -	struct pcie_port *pp;
>> -
>> -	pp = sys_to_pcie(sys);
>> -
>> -	if (global_io_offset < SZ_1M && pp->io_size > 0) {
>> -		sys->io_offset = global_io_offset - pp->io_bus_addr;
>> -		pci_ioremap_io(global_io_offset, pp->io_base);
>> -		global_io_offset += SZ_64K;
>> -		pci_add_resource_offset(&sys->resources, &pp->io,
>> -					sys->io_offset);
>> -	}
>> -
>> -	sys->mem_offset = pp->mem.start - pp->mem_bus_addr;
>> -	pci_add_resource_offset(&sys->resources, &pp->mem, sys->mem_offset);
>> -	pci_add_resource(&sys->resources, &pp->busn);
>> -
>> -	return 1;
>> -}
>> -
>> -static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
>> -{
>> -	struct pci_bus *bus;
>> -	struct pcie_port *pp = sys_to_pcie(sys);
>> -
>> -	pp->root_bus_nr = sys->busnr;
>> -	bus = pci_create_root_bus(pp->dev, sys->busnr,
>> -				  &dw_pcie_ops, sys, &sys->resources);
>> -	if (!bus)
>> -		return NULL;
>> -
>> -	pci_scan_child_bus(bus);
>> -
>> -	if (bus && pp->ops->scan_bus)
>> -		pp->ops->scan_bus(pp);
>> -
>> -	return bus;
>> -}
>> -
>> -static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
>> -{
>> -	struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
>> -	int irq;
>> -
>> -	irq = of_irq_parse_and_map_pci(dev, slot, pin);
>> -	if (!irq)
>> -		irq = pp->irq;
>> -
>> -	return irq;
>> -}
>> -
>> -static struct hw_pci dw_pci = {
>> -	.setup		= dw_pcie_setup,
>> -	.scan		= dw_pcie_scan_bus,
>> -	.map_irq	= dw_pcie_map_irq,
>> -};
>> -
>>  void dw_pcie_setup_rc(struct pcie_port *pp)
>>  {
>>  	u32 val;
> 
> 
> .
> 



  reply	other threads:[~2015-06-05  8:16 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-06-03  8:35 [PATCH v2 0/4] PCI: hisi: Add PCIe host support for Hisilicon Soc Hip05 Zhou Wang
2015-06-03  8:35 ` [PATCH v2 1/4] ARM/PCI: remove align_resource callback in pcibios_align_resource Zhou Wang
2015-06-04 13:18   ` James Morse
2015-06-05  3:53     ` Zhou Wang
2015-06-03  8:35 ` [PATCH v2 2/4] PCI: designware: Add ARM64 support Zhou Wang
2015-06-04 13:19   ` James Morse
2015-06-05  8:11     ` Zhou Wang [this message]
2015-06-09 11:15       ` Lorenzo Pieralisi
2015-06-10 13:35         ` Gabriele Paoloni
2015-06-11  5:44           ` Zhou Wang
2015-06-11 14:32             ` Gabriele Paoloni
2015-06-16 11:30               ` Zhou Wang
2015-06-16 14:14                 ` Gabriele Paoloni
2015-07-13 10:58                   ` Lorenzo Pieralisi
2015-07-13 11:45                     ` Zhou Wang
2015-07-13 14:17                       ` Lorenzo Pieralisi
2015-07-17 10:45                         ` Gabriele Paoloni
2015-06-11  2:51         ` Zhou Wang
2015-06-11  2:44     ` Zhou Wang
2015-06-14 19:18   ` Pratyush Anand
2015-06-16 10:14     ` Zhou Wang
2015-06-03  8:35 ` [PATCH v2 3/4] PCI: hisi: Add PCIe host support for Hisilicon Soc Hip05 Zhou Wang
2015-06-04 13:23   ` James Morse
2015-06-05  8:13     ` Zhou Wang
2015-06-03  8:35 ` [PATCH v2 4/4] Documentation: DT: Add Hisilicon PCIe host binding Zhou Wang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=557159B2.9090103@hisilicon.com \
    --to=wangzhou1@hisilicon.com \
    --cc=Liviu.Dudau@arm.com \
    --cc=arnd@arndb.de \
    --cc=bhelgaas@google.com \
    --cc=devicetree@vger.kernel.org \
    --cc=fabrice.gasnier@st.com \
    --cc=gabriele.paoloni@huawei.com \
    --cc=james.morse@arm.com \
    --cc=jg1.han@samsung.com \
    --cc=liguozhu@hisilicon.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=pratyush.anand@gmail.com \
    --cc=qiuzhenfa@hisilicon.com \
    --cc=yuanzhichang@hisilicon.com \
    --cc=zhangjukuo@huawei.com \
    --cc=zhudacai@hisilicon.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).