From: Anson.Huang@nxp.com
To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
s.hauer@pengutronix.de, kernel@pengutronix.de,
festevam@gmail.com, mturquette@baylibre.com, sboyd@kernel.org,
rjw@rjwysocki.net, viresh.kumar@linaro.org,
leonard.crestez@nxp.com, abel.vesa@nxp.com,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
linux-pm@vger.kernel.org
Cc: Linux-imx@nxp.com
Subject: [PATCH 2/6] arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support
Date: Thu, 15 Aug 2019 06:59:39 -0400 [thread overview]
Message-ID: <1565866783-19672-2-git-send-email-Anson.Huang@nxp.com> (raw)
In-Reply-To: <1565866783-19672-1-git-send-email-Anson.Huang@nxp.com>
From: Anson Huang <Anson.Huang@nxp.com>
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 109 ++++++++++++++++++++++
1 file changed, 109 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 5fce5b1..10ebf77 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -57,6 +57,12 @@
>;
};
+ pinctrl_pmic: pmicirq {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
+ >;
+ };
+
pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
fsl,pins = <
MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
@@ -194,6 +200,109 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
+
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 GPIO_ACTIVE_LOW>;
+ rohm,reset-snvs-powered;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck3_reg: BUCK3 {
+ // BUCK5 in datasheet
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ buck4_reg: BUCK4 {
+ // BUCK6 in datasheet
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // BUCK7 in datasheet
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // BUCK8 in datasheet
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "LDO6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&snvs_pwrkey {
--
2.7.4
next prev parent reply other threads:[~2019-08-15 11:18 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-15 10:59 [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Anson.Huang
2019-08-15 10:59 ` Anson.Huang [this message]
2019-08-15 10:59 ` [PATCH 3/6] cpufreq: Use imx-cpufreq-dt for i.MX8MN's speed grading Anson.Huang
2019-08-15 10:59 ` [PATCH 4/6] cpufreq: imx-cpufreq-dt: Add i.MX8MN support Anson.Huang
2019-08-15 10:59 ` [PATCH 5/6] clk: imx8mn: Add necessary frequency support for ARM PLL table Anson.Huang
2019-08-17 3:52 ` Stephen Boyd
2019-08-17 22:22 ` Anson Huang
2019-08-18 1:11 ` Stephen Boyd
2019-08-18 6:19 ` Anson Huang
2019-08-15 10:59 ` [PATCH 6/6] arm64: dts: imx8mn: Add cpu-freq support Anson.Huang
2019-08-15 14:12 ` [PATCH 1/6] arm64: dts: imx8mn-ddr4-evk: Add i2c1 support Leonard Crestez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1565866783-19672-2-git-send-email-Anson.Huang@nxp.com \
--to=anson.huang@nxp.com \
--cc=Linux-imx@nxp.com \
--cc=abel.vesa@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=kernel@pengutronix.de \
--cc=leonard.crestez@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=rjw@rjwysocki.net \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=sboyd@kernel.org \
--cc=shawnguo@kernel.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).