[v21 0/5] USB DWC3 host wake up support from system suspend

[v21 0/5] USB DWC3 host wake up support from system suspend

[Krishna Kurapati]

Avoiding phy powerdown in host mode when dwc3 is wakeup capable, so that
it can be wake up by devices. Keep usb30_prim gdsc active to retain
controller status during suspend/resume.

Changes in v21:
Fixed compilation issues in dwc3 qcom driver code.

Changes in v20:
Fixed nitpicks in dwc3 qcom driver.
Fixed code changes in dwc3 core driver.

Changes in v19:
Fixed dwc3 driver code changes.

Changes in v18:
Fixed minor nit picks in v17 reported by Matthias.

Changes in v17:
Moved the speed check to glue driver.
Powering down phy's solely based on dwc3 wakeup capability.
Configuring the interrupt functions appropriately.

Changes in v16:
Added changes to power down the phy's during suspend only if dwc3
is not wakeup capable.

Changes in v15:
Added patch to enable wakeup for xhci-plat based on children wakeup status.
Used device_wakeup_path instead of device_children_wakeup_capable

Changes in v14:
Added patch for device_children_wakeup_capable.
Used device_children_wakeup_capable instead of usb_wakeup_enabled_descendants.
Fixed minor nit picks in v13 reported by Matthias.

Changes in v13:
Moved the dt bindings patch to start.
Changed dwc3_set_phy_speed_mode to dwc3_check_phy_speed_mode.
Check wakep-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.
Added GENPD_FLAG_RPM_ALWAYS_ON and set GENPD_FLAG_ALWAYS_ON if
wakeup is supported.

Changes in v12:
Squashed PATCH 1/5 and 2/5 of v11.
Added dt bindings and device tree entry for wakeup-source property
for dwc3 core node.
Dropped redundant phy_set_mode call.


Changes in v11:
Moving back to v8 version
https://patchwork.kernel.org/project/linux-arm-msm/cover/1624882097-23265-1-git-send-email-sanm@codeaurora.org
as we are getting interrupts during suspend
when enabling both DP hs phy irq and DM hs phy irq.
Moved the set phy mode function to dwc3/core.c from xhci-plat.c
We didn't find any other option other than accessing xhci from dwc.

Changes in v10:
PATCH 1/6: Change device_set_wakeup_capable to device_set_wakeup_enable
PATCH 2/6: Remove redundant else part in dwc3_resume_common
PATCH 4/6: Change the irg flags
PATCH 5/6: Set flag GENPD_FLAG_ALWAYS_ON
PATCH 6/6: Remove disable interrupts function and enable
interrupts in probe.


Changes in v9:
Checking with device_may_makeup property instead of phy_power_off flag.
Changed the IRQ flags and removed hs_phy_mode variable.

Changes in v8:
Moved the dwc3 suspend quirk code in dwc3/host.c to xhci-plat.c
Checking phy_power_off flag instead of usb_wakeup_enabled_descendants 
to keep gdsc active.

Changes in v7:
Change in commit text and message in PATCH 1/5 and PATCH 5/5
as per Matthias suggestion.
Added curly braces for if and else if sections in PATCH 4/5.

Changes in v6:
Addressed comments in host.c and core.c
Separated the patches in dwc3-qcom.c to make it simple.
Dropped wakeup-source change as it is not related to this series.

Changes in v5:
Added phy_power_off flag to check presence of wakeup capable devices.
Dropped patch[v4,4/5] as it is present linux-next.
Addressed comments in host.c and dwc3-qcom.c.

Changes in v4:
Addressed Matthias comments raised in v3.

Changes in v3:
Removed need_phy_for_wakeup flag and by default avoiding phy powerdown.
Addressed Matthias comments and added entry for DEV_SUPERSPEED.
Added suspend_quirk in dwc3 host and moved the dwc3_set_phy_speed_flags.
Added wakeup-source dt entry and reading in dwc-qcom.c glue driver.

Changes in v2:
Dropped the patch in clock to set GENPD_FLAG_ACTIVE_WAKEUP flag and 
setting in usb dwc3 driver.
Separated the core patch and glue driver patch.
Made need_phy_for_wakeup flag part of dwc structure and 
hs_phy_flags as unsgined int.
Adrressed the comment on device_init_wakeup call.
Corrected offset for reading portsc register.
Added pacth to support wakeup in xo shutdown case.

Sandeep Maheswaram (5):
  dt-bindings: usb: dwc3: Add wakeup-source property support
  usb: dwc3: core: Host wake up support from system suspend
  usb: dwc3: qcom: Add helper functions to enable,disable wake irqs
  usb: dwc3: qcom: Configure wakeup interrupts during suspend
  usb: dwc3: qcom: Keep power domain on to retain controller status

 .../devicetree/bindings/usb/snps,dwc3.yaml         |   5 +
 drivers/usb/dwc3/core.c                            |   9 +-
 drivers/usb/dwc3/dwc3-qcom.c                       | 140 +++++++++++++++------
 3 files changed, 108 insertions(+), 46 deletions(-)

-- 
2.7.4

[v21 1/5] dt-bindings: usb: dwc3: Add wakeup-source property support

[Krishna Kurapati]

From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Added support for wakeup-source property. This property can be
used to check and power down the phy during system suspend if
wake up is not supported.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
---
 Documentation/devicetree/bindings/usb/snps,dwc3.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
index d41265b..1779d08 100644
--- a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -343,6 +343,11 @@ properties:
       This port is used with the 'usb-role-switch' property  to connect the
       dwc3 to type C connector.
 
+  wakeup-source:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Enable USB remote wakeup.
+
 unevaluatedProperties: false
 
 required:
-- 
2.7.4

[v21 2/5] usb: dwc3: core: Host wake up support from system suspend

[Krishna Kurapati]

From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Check wakeup-source property for dwc3 core node to set the
wakeup capability. Drop the device_init_wakeup call from
runtime suspend and resume.

If the dwc3 is wakeup capable, don't power down the USB PHY(s).
The glue drivers are expected to take care of configuring the
additional wakeup settings if needed based on the dwc3 wakeup
capability status. In some SOC designs, powering off the PHY is
resulting in higher leakage, so this patch save power on such boards.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
---
 drivers/usb/dwc3/core.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 5734219..5017fc9 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1782,6 +1782,7 @@ static int dwc3_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, dwc);
 	dwc3_cache_hwparams(dwc);
+	device_init_wakeup(&pdev->dev, of_property_read_bool(dev->of_node, "wakeup-source"));
 
 	spin_lock_init(&dwc->lock);
 	mutex_init(&dwc->mutex);
@@ -1943,7 +1944,7 @@ static int dwc3_suspend_common(struct dwc3 *dwc, pm_message_t msg)
 		dwc3_core_exit(dwc);
 		break;
 	case DWC3_GCTL_PRTCAP_HOST:
-		if (!PMSG_IS_AUTO(msg)) {
+		if (!PMSG_IS_AUTO(msg) && !device_can_wakeup(dwc->dev)) {
 			dwc3_core_exit(dwc);
 			break;
 		}
@@ -2004,7 +2005,7 @@ static int dwc3_resume_common(struct dwc3 *dwc, pm_message_t msg)
 		spin_unlock_irqrestore(&dwc->lock, flags);
 		break;
 	case DWC3_GCTL_PRTCAP_HOST:
-		if (!PMSG_IS_AUTO(msg)) {
+		if (!PMSG_IS_AUTO(msg) && !device_can_wakeup(dwc->dev)) {
 			ret = dwc3_core_init_for_resume(dwc);
 			if (ret)
 				return ret;
@@ -2081,8 +2082,6 @@ static int dwc3_runtime_suspend(struct device *dev)
 	if (ret)
 		return ret;
 
-	device_init_wakeup(dev, true);
-
 	return 0;
 }
 
@@ -2091,8 +2090,6 @@ static int dwc3_runtime_resume(struct device *dev)
 	struct dwc3     *dwc = dev_get_drvdata(dev);
 	int		ret;
 
-	device_init_wakeup(dev, false);
-
 	ret = dwc3_resume_common(dwc, PMSG_AUTO_RESUME);
 	if (ret)
 		return ret;
-- 
2.7.4

[v21 3/5] usb: dwc3: qcom: Add helper functions to enable,disable wake irqs

[Krishna Kurapati]

From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Adding helper functions to enable,disable wake irqs to make
the code simple and readable.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
---
 drivers/usb/dwc3/dwc3-qcom.c | 58 ++++++++++++++++++++------------------------
 1 file changed, 26 insertions(+), 32 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 6cba990..7352124 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -296,50 +296,44 @@ static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
 	icc_put(qcom->icc_path_apps);
 }
 
+static void dwc3_qcom_enable_wakeup_irq(int irq)
+{
+	if (!irq)
+		return;
+
+	enable_irq(irq);
+	enable_irq_wake(irq);
+}
+
+static void dwc3_qcom_disable_wakeup_irq(int irq)
+{
+	if (!irq)
+		return;
+
+	disable_irq_wake(irq);
+	disable_irq_nosync(irq);
+}
+
 static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
-	if (qcom->hs_phy_irq) {
-		disable_irq_wake(qcom->hs_phy_irq);
-		disable_irq_nosync(qcom->hs_phy_irq);
-	}
+	dwc3_qcom_disable_wakeup_irq(qcom->hs_phy_irq);
 
-	if (qcom->dp_hs_phy_irq) {
-		disable_irq_wake(qcom->dp_hs_phy_irq);
-		disable_irq_nosync(qcom->dp_hs_phy_irq);
-	}
+	dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
 
-	if (qcom->dm_hs_phy_irq) {
-		disable_irq_wake(qcom->dm_hs_phy_irq);
-		disable_irq_nosync(qcom->dm_hs_phy_irq);
-	}
+	dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
 
-	if (qcom->ss_phy_irq) {
-		disable_irq_wake(qcom->ss_phy_irq);
-		disable_irq_nosync(qcom->ss_phy_irq);
-	}
+	dwc3_qcom_disable_wakeup_irq(qcom->ss_phy_irq);
 }
 
 static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 {
-	if (qcom->hs_phy_irq) {
-		enable_irq(qcom->hs_phy_irq);
-		enable_irq_wake(qcom->hs_phy_irq);
-	}
+	dwc3_qcom_enable_wakeup_irq(qcom->hs_phy_irq);
 
-	if (qcom->dp_hs_phy_irq) {
-		enable_irq(qcom->dp_hs_phy_irq);
-		enable_irq_wake(qcom->dp_hs_phy_irq);
-	}
+	dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq);
 
-	if (qcom->dm_hs_phy_irq) {
-		enable_irq(qcom->dm_hs_phy_irq);
-		enable_irq_wake(qcom->dm_hs_phy_irq);
-	}
+	dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq);
 
-	if (qcom->ss_phy_irq) {
-		enable_irq(qcom->ss_phy_irq);
-		enable_irq_wake(qcom->ss_phy_irq);
-	}
+	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq);
 }
 
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
-- 
2.7.4

[v21 4/5] usb: dwc3: qcom: Configure wakeup interrupts during suspend

[Krishna Kurapati]

From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

Configure DP/DM line interrupts based on the USB2 device attached to
the root hub port. When HS/FS device is connected, configure the DP line
as falling edge to detect both disconnect and remote wakeup scenarios. When
LS device is connected, configure DM line as falling edge to detect both
disconnect and remote wakeup. When no device is connected, configure both
DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
---
 drivers/usb/dwc3/dwc3-qcom.c | 72 ++++++++++++++++++++++++++++++++++++++------
 1 file changed, 62 insertions(+), 10 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 7352124..1046ea8 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -20,7 +20,8 @@
 #include <linux/usb/of.h>
 #include <linux/reset.h>
 #include <linux/iopoll.h>
-
+#include <linux/usb/hcd.h>
+#include <linux/usb.h>
 #include "core.h"
 
 /* USB QSCRATCH Hardware registers */
@@ -76,6 +77,7 @@ struct dwc3_qcom {
 	int			dp_hs_phy_irq;
 	int			dm_hs_phy_irq;
 	int			ss_phy_irq;
+	enum usb_device_speed	usb2_speed;
 
 	struct extcon_dev	*edev;
 	struct extcon_dev	*host_edev;
@@ -296,11 +298,34 @@ static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
 	icc_put(qcom->icc_path_apps);
 }
 
-static void dwc3_qcom_enable_wakeup_irq(int irq)
+static enum usb_device_speed dwc3_qcom_read_usb2_speed(struct dwc3_qcom *qcom)
+{
+	struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3);
+	struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
+	struct usb_device *udev;
+
+	/*
+	 * It is possible to query the speed of all children of
+	 * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code
+	 * currently supports only 1 port per controller. So
+	 * this is sufficient.
+	 */
+	udev = usb_hub_find_child(hcd->self.root_hub, 1);
+
+	if (!udev)
+		return USB_SPEED_UNKNOWN;
+
+	return udev->speed;
+}
+
+static void dwc3_qcom_enable_wakeup_irq(int irq, unsigned int polarity)
 {
 	if (!irq)
 		return;
 
+	if (polarity)
+		irq_set_irq_type(irq, polarity);
+
 	enable_irq(irq);
 	enable_irq_wake(irq);
 }
@@ -318,22 +343,47 @@ static void dwc3_qcom_disable_interrupts(struct dwc3_qcom *qcom)
 {
 	dwc3_qcom_disable_wakeup_irq(qcom->hs_phy_irq);
 
-	dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
-
-	dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	if (qcom->usb2_speed == USB_SPEED_LOW) {
+		dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	} else if ((qcom->usb2_speed == USB_SPEED_HIGH) ||
+			(qcom->usb2_speed == USB_SPEED_FULL)) {
+		dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
+	} else {
+		dwc3_qcom_disable_wakeup_irq(qcom->dp_hs_phy_irq);
+		dwc3_qcom_disable_wakeup_irq(qcom->dm_hs_phy_irq);
+	}
 
 	dwc3_qcom_disable_wakeup_irq(qcom->ss_phy_irq);
 }
 
 static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
 {
-	dwc3_qcom_enable_wakeup_irq(qcom->hs_phy_irq);
+	dwc3_qcom_enable_wakeup_irq(qcom->hs_phy_irq, 0);
 
-	dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq);
+	/*
+	 * Configure DP/DM line interrupts based on the USB2 device attached to
+	 * the root hub port. When HS/FS device is connected, configure the DP line
+	 * as falling edge to detect both disconnect and remote wakeup scenarios. When
+	 * LS device is connected, configure DM line as falling edge to detect both
+	 * disconnect and remote wakeup. When no device is connected, configure both
+	 * DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
+	 */
 
-	dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq);
+	if (qcom->usb2_speed == USB_SPEED_LOW) {
+		dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq,
+						IRQ_TYPE_EDGE_FALLING);
+	} else if ((qcom->usb2_speed == USB_SPEED_HIGH) ||
+			(qcom->usb2_speed == USB_SPEED_FULL)) {
+		dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq,
+						IRQ_TYPE_EDGE_FALLING);
+	} else {
+		dwc3_qcom_enable_wakeup_irq(qcom->dp_hs_phy_irq,
+						IRQ_TYPE_EDGE_RISING);
+		dwc3_qcom_enable_wakeup_irq(qcom->dm_hs_phy_irq,
+						IRQ_TYPE_EDGE_RISING);
+	}
 
-	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq);
+	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq, 0);
 }
 
 static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
@@ -355,8 +405,10 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
 	if (ret)
 		dev_warn(qcom->dev, "failed to disable interconnect: %d\n", ret);
 
-	if (device_may_wakeup(qcom->dev))
+	if (device_may_wakeup(qcom->dev)) {
+		qcom->usb2_speed = dwc3_qcom_read_usb2_speed(qcom);
 		dwc3_qcom_enable_interrupts(qcom);
+	}
 
 	qcom->is_suspended = true;
 
-- 
2.7.4

Re: [v21 4/5] usb: dwc3: qcom: Configure wakeup interrupts during suspend

[Matthias Kaehlcke]

On Mon, Jun 13, 2022 at 10:00:53AM +0530, Krishna Kurapati wrote:
> From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> 
> Configure DP/DM line interrupts based on the USB2 device attached to
> the root hub port. When HS/FS device is connected, configure the DP line
> as falling edge to detect both disconnect and remote wakeup scenarios. When
> LS device is connected, configure DM line as falling edge to detect both
> disconnect and remote wakeup. When no device is connected, configure both
> DP and DM lines as rising edge to detect HS/HS/LS device connect scenario.
> 
> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
> Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
> ---
>  drivers/usb/dwc3/dwc3-qcom.c | 72 ++++++++++++++++++++++++++++++++++++++------
>  1 file changed, 62 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> index 7352124..1046ea8 100644
> --- a/drivers/usb/dwc3/dwc3-qcom.c
> +++ b/drivers/usb/dwc3/dwc3-qcom.c
> @@ -20,7 +20,8 @@
>  #include <linux/usb/of.h>
>  #include <linux/reset.h>
>  #include <linux/iopoll.h>
> -
> +#include <linux/usb/hcd.h>
> +#include <linux/usb.h>
>  #include "core.h"
>  
>  /* USB QSCRATCH Hardware registers */
> @@ -76,6 +77,7 @@ struct dwc3_qcom {
>  	int			dp_hs_phy_irq;
>  	int			dm_hs_phy_irq;
>  	int			ss_phy_irq;
> +	enum usb_device_speed	usb2_speed;
>  
>  	struct extcon_dev	*edev;
>  	struct extcon_dev	*host_edev;
> @@ -296,11 +298,34 @@ static void dwc3_qcom_interconnect_exit(struct dwc3_qcom *qcom)
>  	icc_put(qcom->icc_path_apps);
>  }
>  
> -static void dwc3_qcom_enable_wakeup_irq(int irq)
> +static enum usb_device_speed dwc3_qcom_read_usb2_speed(struct dwc3_qcom *qcom)
> +{
> +	struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3);
> +	struct usb_hcd *hcd = platform_get_drvdata(dwc->xhci);
> +	struct usb_device *udev;
> +
> +	/*
> +	 * It is possible to query the speed of all children of
> +	 * USB2.0 root hub via usb_hub_for_each_child(). DWC3 code
> +	 * currently supports only 1 port per controller. So
> +	 * this is sufficient.
> +	 */

nit: not sure it's really valuable to mention what could be done
theoretically. Saying that the dwc3 driver currently only
supports one port per controller should be enough.

No need to respin for this,

> +	udev = usb_hub_find_child(hcd->self.root_hub, 1);
> +
> +	if (!udev)
> +		return USB_SPEED_UNKNOWN;
> +
> +	return udev->speed;
> +}
> +
> +static void dwc3_qcom_enable_wakeup_irq(int irq, unsigned int polarity)

'polarity' isn't really accurate, the parameter also encodes whether the IRQ
is edge or level triggered. 'irq_type' would be clearer.

Also no need to respin just for this.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>

[v21 5/5] usb: dwc3: qcom: Keep power domain on to retain controller status

[Krishna Kurapati]

From: Sandeep Maheswaram <quic_c_sanm@quicinc.com>

If dwc3 is wakeup capable, keep the power domain always ON so that
wakeup from system suspend can be supported. Otherwise, keep the
power domain ON only during runtime suspend to support wakeup from
runtime suspend.

Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
---
 drivers/usb/dwc3/dwc3-qcom.c | 28 +++++++++++++++++++++-------
 1 file changed, 21 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
index 1046ea8..7703655 100644
--- a/drivers/usb/dwc3/dwc3-qcom.c
+++ b/drivers/usb/dwc3/dwc3-qcom.c
@@ -17,6 +17,7 @@
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 #include <linux/phy/phy.h>
+#include <linux/pm_domain.h>
 #include <linux/usb/of.h>
 #include <linux/reset.h>
 #include <linux/iopoll.h>
@@ -756,12 +757,13 @@ dwc3_qcom_create_urs_usb_platdev(struct device *dev)
 
 static int dwc3_qcom_probe(struct platform_device *pdev)
 {
-	struct device_node	*np = pdev->dev.of_node;
-	struct device		*dev = &pdev->dev;
-	struct dwc3_qcom	*qcom;
-	struct resource		*res, *parent_res = NULL;
-	int			ret, i;
-	bool			ignore_pipe_clk;
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	struct dwc3_qcom *qcom;
+	struct resource	*res, *parent_res = NULL;
+	int ret, i;
+	bool ignore_pipe_clk;
+	struct generic_pm_domain *genpd;
 
 	qcom = devm_kzalloc(&pdev->dev, sizeof(*qcom), GFP_KERNEL);
 	if (!qcom)
@@ -770,6 +772,8 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, qcom);
 	qcom->dev = &pdev->dev;
 
+	genpd = pd_to_genpd(qcom->dev->pm_domain);
+
 	if (has_acpi_companion(dev)) {
 		qcom->acpi_pdata = acpi_device_get_match_data(dev);
 		if (!qcom->acpi_pdata) {
@@ -877,7 +881,17 @@ static int dwc3_qcom_probe(struct platform_device *pdev)
 	if (ret)
 		goto interconnect_exit;
 
-	device_init_wakeup(&pdev->dev, 1);
+	if (device_can_wakeup(&qcom->dwc3->dev)) {
+		/*
+		 * Setting GENPD_FLAG_ALWAYS_ON flag takes care of keeping
+		 * genpd on in both runtime suspend and system suspend cases.
+		 */
+		genpd->flags |= GENPD_FLAG_ALWAYS_ON;
+		device_init_wakeup(&pdev->dev, true);
+	} else {
+		genpd->flags |= GENPD_FLAG_RPM_ALWAYS_ON;
+	}
+
 	qcom->is_suspended = false;
 	pm_runtime_set_active(dev);
 	pm_runtime_enable(dev);
-- 
2.7.4