* [PATCH v10 01/10] qom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 19:41 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs Lina Iyer
` (9 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Follow the scm.c and move scm-boot files to drivers/soc/qcom. The
guidance is to clean files out from mach-qcom and move to drivers/soc
area.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/mach-qcom/Makefile | 1 -
arch/arm/mach-qcom/platsmp.c | 2 +-
drivers/soc/qcom/Makefile | 2 +-
{arch/arm/mach-qcom => drivers/soc/qcom}/scm-boot.c | 4 ++--
{arch/arm/mach-qcom => include/soc/qcom}/scm-boot.h | 0
5 files changed, 4 insertions(+), 5 deletions(-)
rename {arch/arm/mach-qcom => drivers/soc/qcom}/scm-boot.c (97%)
rename {arch/arm/mach-qcom => include/soc/qcom}/scm-boot.h (100%)
diff --git a/arch/arm/mach-qcom/Makefile b/arch/arm/mach-qcom/Makefile
index db41e8c..e324375 100644
--- a/arch/arm/mach-qcom/Makefile
+++ b/arch/arm/mach-qcom/Makefile
@@ -1,3 +1,2 @@
obj-y := board.o
obj-$(CONFIG_SMP) += platsmp.o
-obj-$(CONFIG_QCOM_SCM) += scm-boot.o
diff --git a/arch/arm/mach-qcom/platsmp.c b/arch/arm/mach-qcom/platsmp.c
index d690856..a692bcb 100644
--- a/arch/arm/mach-qcom/platsmp.c
+++ b/arch/arm/mach-qcom/platsmp.c
@@ -20,7 +20,7 @@
#include <asm/smp_plat.h>
-#include "scm-boot.h"
+#include <soc/qcom/scm-boot.h>
#define VDD_SC1_ARRAY_CLAMP_GFS_CTL 0x35a0
#define SCSS_CPU1CORE_RESET 0x2d80
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index a39446d..70d52ed 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -1,3 +1,3 @@
obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o
CFLAGS_scm.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
-obj-$(CONFIG_QCOM_SCM) += scm.o
+obj-$(CONFIG_QCOM_SCM) += scm.o scm-boot.o
diff --git a/arch/arm/mach-qcom/scm-boot.c b/drivers/soc/qcom/scm-boot.c
similarity index 97%
rename from arch/arm/mach-qcom/scm-boot.c
rename to drivers/soc/qcom/scm-boot.c
index 5add20e..60ff7b4 100644
--- a/arch/arm/mach-qcom/scm-boot.c
+++ b/drivers/soc/qcom/scm-boot.c
@@ -17,9 +17,9 @@
#include <linux/module.h>
#include <linux/slab.h>
-#include <soc/qcom/scm.h>
-#include "scm-boot.h"
+#include <soc/qcom/scm.h>
+#include <soc/qcom/scm-boot.h>
/*
* Set the cold/warm boot address for one of the CPU cores.
diff --git a/arch/arm/mach-qcom/scm-boot.h b/include/soc/qcom/scm-boot.h
similarity index 100%
rename from arch/arm/mach-qcom/scm-boot.h
rename to include/soc/qcom/scm-boot.h
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 01/10] qom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom
2014-11-21 18:03 ` [PATCH v10 01/10] qom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom Lina Iyer
@ 2014-11-26 19:41 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 19:41 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> Follow the scm.c and move scm-boot files to drivers/soc/qcom. The
> guidance is to clean files out from mach-qcom and move to drivers/soc
> area.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
2014-11-21 18:03 ` [PATCH v10 01/10] qom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 9:41 ` Daniel Lezcano
2014-11-26 19:48 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 03/10] qcom: spm: Add Subsystem Power Manager driver Lina Iyer
` (8 subsequent siblings)
10 siblings, 2 replies; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Quad core SoCs like APQ8074, APQ8064, APQ8084 need SCM support set up
warm boot addresses in the Secure Monitor. Extend the SCM flags to
support warm boot addresses for secondary cores.
We do not need to export the warmboot flags. Move them into the
implementation file.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
drivers/soc/qcom/scm-boot.c | 31 +++++++++++++++++++++++++++++++
include/soc/qcom/scm-boot.h | 3 +--
2 files changed, 32 insertions(+), 2 deletions(-)
diff --git a/drivers/soc/qcom/scm-boot.c b/drivers/soc/qcom/scm-boot.c
index 60ff7b4..0871659 100644
--- a/drivers/soc/qcom/scm-boot.c
+++ b/drivers/soc/qcom/scm-boot.c
@@ -21,6 +21,23 @@
#include <soc/qcom/scm.h>
#include <soc/qcom/scm-boot.h>
+#define SCM_FLAG_WARMBOOT_CPU0 0x04
+#define SCM_FLAG_WARMBOOT_CPU1 0x02
+#define SCM_FLAG_WARMBOOT_CPU2 0x10
+#define SCM_FLAG_WARMBOOT_CPU3 0x40
+
+struct scm_warmboot {
+ int flag;
+ void *entry;
+};
+
+static struct scm_warmboot scm_flags[] = {
+ { .flag = SCM_FLAG_WARMBOOT_CPU0 },
+ { .flag = SCM_FLAG_WARMBOOT_CPU1 },
+ { .flag = SCM_FLAG_WARMBOOT_CPU2 },
+ { .flag = SCM_FLAG_WARMBOOT_CPU3 },
+};
+
/*
* Set the cold/warm boot address for one of the CPU cores.
*/
@@ -37,3 +54,17 @@ int scm_set_boot_addr(phys_addr_t addr, int flags)
&cmd, sizeof(cmd), NULL, 0);
}
EXPORT_SYMBOL(scm_set_boot_addr);
+
+int scm_set_warm_boot_addr(void *entry, int cpu)
+{
+ int ret;
+
+ if (entry == scm_flags[cpu].entry)
+ return 0;
+
+ ret = scm_set_boot_addr(virt_to_phys(entry), scm_flags[cpu].flag);
+ if (!ret)
+ scm_flags[cpu].entry = entry;
+
+ return ret;
+}
diff --git a/include/soc/qcom/scm-boot.h b/include/soc/qcom/scm-boot.h
index 6aabb24..529f55a 100644
--- a/include/soc/qcom/scm-boot.h
+++ b/include/soc/qcom/scm-boot.h
@@ -16,9 +16,8 @@
#define SCM_FLAG_COLDBOOT_CPU1 0x01
#define SCM_FLAG_COLDBOOT_CPU2 0x08
#define SCM_FLAG_COLDBOOT_CPU3 0x20
-#define SCM_FLAG_WARMBOOT_CPU0 0x04
-#define SCM_FLAG_WARMBOOT_CPU1 0x02
int scm_set_boot_addr(phys_addr_t addr, int flags);
+int scm_set_warm_boot_addr(void *entry, int cpu);
#endif
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs
2014-11-21 18:03 ` [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs Lina Iyer
@ 2014-11-26 9:41 ` Daniel Lezcano
2014-11-26 19:48 ` Stephen Boyd
1 sibling, 0 replies; 28+ messages in thread
From: Daniel Lezcano @ 2014-11-26 9:41 UTC (permalink / raw)
To: Lina Iyer, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 07:03 PM, Lina Iyer wrote:
> Quad core SoCs like APQ8074, APQ8064, APQ8084 need SCM support set up
> warm boot addresses in the Secure Monitor. Extend the SCM flags to
> support warm boot addresses for secondary cores.
>
> We do not need to export the warmboot flags. Move them into the
> implementation file.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
+ one comment below
> ---
> drivers/soc/qcom/scm-boot.c | 31 +++++++++++++++++++++++++++++++
> include/soc/qcom/scm-boot.h | 3 +--
> 2 files changed, 32 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/soc/qcom/scm-boot.c b/drivers/soc/qcom/scm-boot.c
> index 60ff7b4..0871659 100644
> --- a/drivers/soc/qcom/scm-boot.c
> +++ b/drivers/soc/qcom/scm-boot.c
> @@ -21,6 +21,23 @@
> #include <soc/qcom/scm.h>
> #include <soc/qcom/scm-boot.h>
>
> +#define SCM_FLAG_WARMBOOT_CPU0 0x04
> +#define SCM_FLAG_WARMBOOT_CPU1 0x02
> +#define SCM_FLAG_WARMBOOT_CPU2 0x10
> +#define SCM_FLAG_WARMBOOT_CPU3 0x40
> +
> +struct scm_warmboot {
> + int flag;
> + void *entry;
> +};
> +
> +static struct scm_warmboot scm_flags[] = {
> + { .flag = SCM_FLAG_WARMBOOT_CPU0 },
> + { .flag = SCM_FLAG_WARMBOOT_CPU1 },
> + { .flag = SCM_FLAG_WARMBOOT_CPU2 },
> + { .flag = SCM_FLAG_WARMBOOT_CPU3 },
> +};
> +
> /*
> * Set the cold/warm boot address for one of the CPU cores.
> */
> @@ -37,3 +54,17 @@ int scm_set_boot_addr(phys_addr_t addr, int flags)
> &cmd, sizeof(cmd), NULL, 0);
> }
> EXPORT_SYMBOL(scm_set_boot_addr);
> +
> +int scm_set_warm_boot_addr(void *entry, int cpu)
> +{
> + int ret;
> +
> + if (entry == scm_flags[cpu].entry)
> + return 0;
IMO, this test deserves a comment of why this is needed.
> +
> + ret = scm_set_boot_addr(virt_to_phys(entry), scm_flags[cpu].flag);
> + if (!ret)
> + scm_flags[cpu].entry = entry;
> +
> + return ret;
> +}
> diff --git a/include/soc/qcom/scm-boot.h b/include/soc/qcom/scm-boot.h
> index 6aabb24..529f55a 100644
> --- a/include/soc/qcom/scm-boot.h
> +++ b/include/soc/qcom/scm-boot.h
> @@ -16,9 +16,8 @@
> #define SCM_FLAG_COLDBOOT_CPU1 0x01
> #define SCM_FLAG_COLDBOOT_CPU2 0x08
> #define SCM_FLAG_COLDBOOT_CPU3 0x20
> -#define SCM_FLAG_WARMBOOT_CPU0 0x04
> -#define SCM_FLAG_WARMBOOT_CPU1 0x02
>
> int scm_set_boot_addr(phys_addr_t addr, int flags);
> +int scm_set_warm_boot_addr(void *entry, int cpu);
>
> #endif
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs
2014-11-21 18:03 ` [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs Lina Iyer
2014-11-26 9:41 ` Daniel Lezcano
@ 2014-11-26 19:48 ` Stephen Boyd
2014-11-26 19:56 ` Lina Iyer
1 sibling, 1 reply; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 19:48 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> @@ -37,3 +54,17 @@ int scm_set_boot_addr(phys_addr_t addr, int flags)
> &cmd, sizeof(cmd), NULL, 0);
> }
> EXPORT_SYMBOL(scm_set_boot_addr);
> +
> +int scm_set_warm_boot_addr(void *entry, int cpu)
> +{
> + int ret;
> +
> + if (entry == scm_flags[cpu].entry)
> + return 0;
Is the entry going to be different at some point? I wonder why we can't
just call this function once when the SPM device probes to setup the
entry point to cpu_resume()?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs
2014-11-26 19:48 ` Stephen Boyd
@ 2014-11-26 19:56 ` Lina Iyer
0 siblings, 0 replies; 28+ messages in thread
From: Lina Iyer @ 2014-11-26 19:56 UTC (permalink / raw)
To: Stephen Boyd
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On Wed, Nov 26 2014 at 12:48 -0700, Stephen Boyd wrote:
>On 11/21/2014 10:03 AM, Lina Iyer wrote:
>>@@ -37,3 +54,17 @@ int scm_set_boot_addr(phys_addr_t addr, int flags)
>> &cmd, sizeof(cmd), NULL, 0);
>> }
>> EXPORT_SYMBOL(scm_set_boot_addr);
>>+
>>+int scm_set_warm_boot_addr(void *entry, int cpu)
>>+{
>>+ int ret;
>>+
>>+ if (entry == scm_flags[cpu].entry)
>>+ return 0;
>
>Is the entry going to be different at some point? I wonder why we
>can't just call this function once when the SPM device probes to setup
>the entry point to cpu_resume()?
>
Hotplug would use a different re-entry point. Hence the check.
>--
>Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
>a Linux Foundation Collaborative Project
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 03/10] qcom: spm: Add Subsystem Power Manager driver
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
2014-11-21 18:03 ` [PATCH v10 01/10] qom: scm: Move scm-boot files to drivers/soc/qcom/ and include/soc/qcom Lina Iyer
2014-11-21 18:03 ` [PATCH v10 02/10] qcom: scm: Add SCM warmboot support for quad core SoCs Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:00 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs Lina Iyer
` (7 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
SPM is a hardware block that controls the peripheral logic surrounding
the application cores (cpu/l$). When the core executes WFI instruction,
the SPM takes over the putting the core in low power state as
configured. The wake up for the SPM is an interrupt at the GIC, which
then completes the rest of low power mode sequence and brings the core
out of low power mode.
The SPM has a set of control registers that configure the SPMs
individually based on the type of the core and the runtime conditions.
SPM is a finite state machine block to which a sequence is provided and
it interprets the bytes and executes them in sequence. Each low power
mode that the core can enter into is provided to the SPM as a sequence.
Configure the SPM to set the core (cpu or L2) into its low power mode,
the index of the first command in the sequence is set in the SPM_CTL
register. When the core executes ARM wfi instruction, it triggers the
SPM state machine to start executing from that index. The SPM state
machine waits until the interrupt occurs and starts executing the rest
of the sequence until it hits the end of the sequence. The end of the
sequence jumps the core out of its low power mode.
Add support for an idle driver to set up the SPM to place the core in
Standby or Standalone power collapse mode when the core is idle.
Based on work by: Mahesh Sivasubramanian <msivasub@codeaurora.org>,
Ai Li <ali@codeaurora.org>, Praveen Chidambaram <pchidamb@codeaurora.org>
Original tree available at -
git://codeaurora.org/quic/la/kernel/msm-3.10.git
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
.../devicetree/bindings/arm/msm/qcom,saw2.txt | 31 +-
drivers/soc/qcom/Kconfig | 8 +
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/spm.c | 332 +++++++++++++++++++++
include/soc/qcom/pm.h | 31 ++
5 files changed, 397 insertions(+), 6 deletions(-)
create mode 100644 drivers/soc/qcom/spm.c
create mode 100644 include/soc/qcom/pm.h
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
index 1505fb8..690c3c0 100644
--- a/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,saw2.txt
@@ -2,11 +2,20 @@ SPM AVS Wrapper 2 (SAW2)
The SAW2 is a wrapper around the Subsystem Power Manager (SPM) and the
Adaptive Voltage Scaling (AVS) hardware. The SPM is a programmable
-micro-controller that transitions a piece of hardware (like a processor or
+power-controller that transitions a piece of hardware (like a processor or
subsystem) into and out of low power modes via a direct connection to
the PMIC. It can also be wired up to interact with other processors in the
system, notifying them when a low power state is entered or exited.
+Multiple revisions of the SAW hardware are supported using these Device Nodes.
+SAW2 revisions differ in the register offset and configuration data. Also, the
+same revision of the SAW in different SoCs may have different configuration
+data due the the differences in hardware capabilities. Hence the SoC name, the
+version of the SAW hardware in that SoC and the distinction between cpu (big
+or Little) or cache, may be needed to uniquely identify the SAW register
+configuration and initialization data. The compatible string is used to
+indicate this parameter.
+
PROPERTIES
- compatible:
@@ -14,10 +23,13 @@ PROPERTIES
Value type: <string>
Definition: shall contain "qcom,saw2". A more specific value should be
one of:
- "qcom,saw2-v1"
- "qcom,saw2-v1.1"
- "qcom,saw2-v2"
- "qcom,saw2-v2.1"
+ "qcom,saw2-v1"
+ "qcom,saw2-v1.1"
+ "qcom,saw2-v2"
+ "qcom,saw2-v2.1"
+ "qcom,apq8064-saw2-v1.1-cpu"
+ "qcom,msm8974-saw2-v2.1-cpu"
+ "qcom,apq8084-saw2-v2.1-cpu"
- reg:
Usage: required
@@ -26,10 +38,17 @@ PROPERTIES
the register region. An optional second element specifies
the base address and size of the alias register region.
+- regulator:
+ Usage: optional
+ Value type: boolean
+ Definition: Indicates that this SPM device acts as a regulator device
+ device for the core (CPU or Cache) the SPM is attached
+ to.
Example:
- regulator@2099000 {
+ power-controller@2099000 {
compatible = "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+ regulator;
};
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 7dcd554..012fb37 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -11,3 +11,11 @@ config QCOM_GSBI
config QCOM_SCM
bool
+
+config QCOM_PM
+ bool "Qualcomm Power Management"
+ depends on ARCH_QCOM
+ help
+ QCOM Platform specific power driver to manage cores and L2 low power
+ modes. It interface with various system drivers to put the cores in
+ low power modes.
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 70d52ed..20b329f 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -1,3 +1,4 @@
obj-$(CONFIG_QCOM_GSBI) += qcom_gsbi.o
+obj-$(CONFIG_QCOM_PM) += spm.o
CFLAGS_scm.o :=$(call as-instr,.arch_extension sec,-DREQUIRES_SEC=1)
obj-$(CONFIG_QCOM_SCM) += scm.o scm-boot.o
diff --git a/drivers/soc/qcom/spm.c b/drivers/soc/qcom/spm.c
new file mode 100644
index 0000000..c2dfa38
--- /dev/null
+++ b/drivers/soc/qcom/spm.c
@@ -0,0 +1,332 @@
+/* Copyright (c) 2011-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/cpuidle.h>
+#include <linux/cpu_pm.h>
+
+#include <asm/proc-fns.h>
+#include <asm/suspend.h>
+
+#include <soc/qcom/pm.h>
+#include <soc/qcom/pm.h>
+#include <soc/qcom/scm.h>
+#include <soc/qcom/scm-boot.h>
+
+
+#define SCM_CMD_TERMINATE_PC 0x2
+#define SCM_FLUSH_FLAG_MASK 0x3
+#define SCM_L2_ON 0x0
+#define SCM_L2_OFF 0x1
+#define MAX_PMIC_DATA 2
+#define MAX_SEQ_DATA 64
+#define SPM_CTL_INDEX 0x7f
+#define SPM_CTL_INDEX_SHIFT 4
+#define SPM_CTL_EN BIT(0)
+
+enum spm_reg {
+ SPM_REG_CFG,
+ SPM_REG_SPM_CTL,
+ SPM_REG_DLY,
+ SPM_REG_PMIC_DLY,
+ SPM_REG_PMIC_DATA_0,
+ SPM_REG_PMIC_DATA_1,
+ SPM_REG_VCTL,
+ SPM_REG_SEQ_ENTRY,
+ SPM_REG_SPM_STS,
+ SPM_REG_PMIC_STS,
+ SPM_REG_NR,
+};
+
+struct spm_reg_data {
+ /* Register position */
+ const u8 *reg_offset;
+
+ /* Register initialization values */
+ u32 spm_cfg;
+ u32 spm_dly;
+ u32 pmic_dly;
+ u32 pmic_data[MAX_PMIC_DATA];
+
+ /* Sequences and start indices */
+ u8 seq[MAX_SEQ_DATA];
+ u8 start_index[PM_SLEEP_MODE_NR];
+
+};
+
+struct spm_driver_data {
+ void __iomem *reg_base;
+ const struct spm_reg_data *reg_data;
+ bool available;
+};
+
+static const u8 spm_reg_offset_v2_1[SPM_REG_NR] = {
+ [SPM_REG_CFG] = 0x08,
+ [SPM_REG_SPM_CTL] = 0x30,
+ [SPM_REG_DLY] = 0x34,
+ [SPM_REG_SEQ_ENTRY] = 0x80,
+};
+
+/* SPM register data for 8974, 8084 */
+static const struct spm_reg_data spm_reg_8974_8084_cpu = {
+ .reg_offset = spm_reg_offset_v2_1,
+ .spm_cfg = 0x1,
+ .spm_dly = 0x3C102800,
+ .seq = { 0x03, 0x0B, 0x0F, 0x00, 0x20, 0x80, 0x10, 0xE8, 0x5B, 0x03,
+ 0x3B, 0xE8, 0x5B, 0x82, 0x10, 0x0B, 0x30, 0x06, 0x26, 0x30,
+ 0x0F },
+ .start_index[PM_SLEEP_MODE_STBY] = 0,
+ .start_index[PM_SLEEP_MODE_SPC] = 3,
+};
+
+static const u8 spm_reg_offset_v1_1[SPM_REG_NR] = {
+ [SPM_REG_CFG] = 0x08,
+ [SPM_REG_SPM_CTL] = 0x20,
+ [SPM_REG_PMIC_DLY] = 0x24,
+ [SPM_REG_PMIC_DATA_0] = 0x28,
+ [SPM_REG_PMIC_DATA_1] = 0x2C,
+ [SPM_REG_SEQ_ENTRY] = 0x80,
+};
+
+/* SPM register data for 8064 */
+static const struct spm_reg_data spm_reg_8064_cpu = {
+ .reg_offset = spm_reg_offset_v1_1,
+ .spm_cfg = 0x1F,
+ .pmic_dly = 0x02020004,
+ .pmic_data[0] = 0x0084009C,
+ .pmic_data[1] = 0x00A4001C,
+ .seq = { 0x03, 0x0F, 0x00, 0x24, 0x54, 0x10, 0x09, 0x03, 0x01,
+ 0x10, 0x54, 0x30, 0x0C, 0x24, 0x30, 0x0F },
+ .start_index[PM_SLEEP_MODE_STBY] = 0,
+ .start_index[PM_SLEEP_MODE_SPC] = 2,
+};
+
+static DEFINE_PER_CPU_SHARED_ALIGNED(struct spm_driver_data, cpu_spm_drv);
+
+static inline void spm_register_write(struct spm_driver_data *drv,
+ enum spm_reg reg, u32 val)
+{
+ if (drv->reg_data->reg_offset[reg])
+ writel_relaxed(val, drv->reg_base +
+ drv->reg_data->reg_offset[reg]);
+}
+
+static inline u32 spm_register_read(struct spm_driver_data *drv,
+ enum spm_reg reg)
+{
+ return readl_relaxed(drv->reg_base + drv->reg_data->reg_offset[reg]);
+}
+
+/**
+ * spm_set_low_power_mode() - Configure SPM start address for low power mode
+ * @mode: SPM LPM mode to enter
+ */
+static int spm_set_low_power_mode(enum pm_sleep_mode mode)
+{
+ struct spm_driver_data *drv = this_cpu_ptr(&cpu_spm_drv);
+ u32 start_index;
+ u32 ctl_val;
+
+ if (!drv->available)
+ return -ENXIO;
+
+ start_index = drv->reg_data->start_index[mode];
+
+ ctl_val = spm_register_read(drv, SPM_REG_SPM_CTL);
+ ctl_val &= ~(SPM_CTL_INDEX << SPM_CTL_INDEX_SHIFT);
+ ctl_val |= start_index << SPM_CTL_INDEX_SHIFT;
+ ctl_val |= SPM_CTL_EN;
+ spm_register_write(drv, SPM_REG_SPM_CTL, ctl_val);
+
+ /* Ensure we have written the start address */
+ wmb();
+
+ return 0;
+}
+
+static int qcom_pm_collapse(unsigned long int unused)
+{
+ int ret;
+ u32 flag;
+ int cpu = smp_processor_id();
+
+ ret = scm_set_warm_boot_addr(cpu_resume, cpu);
+ if (ret)
+ return ret;
+
+ flag = SCM_L2_ON & SCM_FLUSH_FLAG_MASK;
+ scm_call_atomic1(SCM_SVC_BOOT, SCM_CMD_TERMINATE_PC, flag);
+
+ /**
+ * Returns here only if there was a pending interrupt and we did not
+ * power down as a result.
+ */
+ return 0;
+}
+
+static int qcom_cpu_standby(void *unused)
+{
+ int ret;
+
+ ret = spm_set_low_power_mode(PM_SLEEP_MODE_STBY);
+ if (ret)
+ return ret;
+
+ cpu_do_idle();
+
+ return 0;
+}
+
+static int qcom_cpu_spc(void *unused)
+{ int ret;
+
+ ret = spm_set_low_power_mode(PM_SLEEP_MODE_STBY);
+ if (ret)
+ return ret;
+
+ cpu_pm_enter();
+ cpu_suspend(0, qcom_pm_collapse);
+ cpu_pm_exit();
+
+ return 0;
+}
+
+static struct spm_driver_data *spm_get_drv(struct platform_device *pdev,
+ int *spm_cpu)
+{
+ struct spm_driver_data *drv = NULL;
+ struct device_node *cpu_node, *saw_node;
+ int cpu;
+
+ for_each_possible_cpu(cpu) {
+ cpu_node = of_cpu_device_node_get(cpu);
+ if (!cpu_node)
+ continue;
+ saw_node = of_parse_phandle(cpu_node, "qcom,saw", 0);
+ if (saw_node) {
+ if (saw_node == pdev->dev.of_node)
+ drv = &per_cpu(cpu_spm_drv, cpu);
+ of_node_put(saw_node);
+ }
+ of_node_put(cpu_node);
+ if (drv) {
+ *spm_cpu = cpu;
+ break;
+ }
+ }
+
+ return drv;
+}
+
+static const struct of_device_id spm_match_table[] = {
+ { .compatible = "qcom,msm8974-saw2-v2.1-cpu",
+ .data = &spm_reg_8974_8084_cpu },
+ { .compatible = "qcom,apq8084-saw2-v2.1-cpu",
+ .data = &spm_reg_8974_8084_cpu },
+ { .compatible = "qcom,apq8064-saw2-v1.1-cpu",
+ .data = &spm_reg_8064_cpu },
+ { },
+};
+
+static const struct qcom_cpu_pm_ops lpm_ops = {
+ .standby = qcom_cpu_standby,
+ .spc = qcom_cpu_spc,
+};
+
+static const struct platform_device_info qcom_cpuidle_info = {
+ .name = "qcom_cpuidle",
+ .id = -1,
+ .data = &lpm_ops,
+ .size_data = sizeof(lpm_ops),
+};
+
+static int spm_dev_probe(struct platform_device *pdev)
+{
+ struct spm_driver_data *drv;
+ struct resource *res;
+ const struct of_device_id *match_id;
+ void __iomem *addr;
+ int cpu = -EINVAL;
+ static bool cpuidle_drv_init;
+
+ drv = spm_get_drv(pdev, &cpu);
+ if (!drv || cpu < 0)
+ return -EINVAL;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ drv->reg_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(drv->reg_base))
+ return PTR_ERR(drv->reg_base);
+
+ match_id = of_match_node(spm_match_table, pdev->dev.of_node);
+ if (!match_id)
+ return -ENODEV;
+
+ drv->reg_data = match_id->data;
+
+ /* Write the SPM sequences, first.. */
+ addr = drv->reg_base + drv->reg_data->reg_offset[SPM_REG_SEQ_ENTRY];
+ __iowrite32_copy(addr, drv->reg_data->seq,
+ ARRAY_SIZE(drv->reg_data->seq) / 4);
+
+ /* ..and then, the control registers.
+ * On some SoC's if the control registers are written first and if the
+ * CPU was held in reset, the reset signal could trigger the SPM state
+ * machine, before the sequences are completely written.
+ */
+ spm_register_write(drv, SPM_REG_CFG, drv->reg_data->spm_cfg);
+ spm_register_write(drv, SPM_REG_DLY, drv->reg_data->spm_dly);
+ spm_register_write(drv, SPM_REG_PMIC_DLY, drv->reg_data->pmic_dly);
+
+ spm_register_write(drv, SPM_REG_PMIC_DATA_0,
+ drv->reg_data->pmic_data[0]);
+ spm_register_write(drv, SPM_REG_PMIC_DATA_1,
+ drv->reg_data->pmic_data[1]);
+
+ /**
+ * Ensure all observers see the above register writes before the
+ * cpuidle driver is allowed to use the SPM.
+ */
+ wmb();
+ drv->available = true;
+
+ if (!cpuidle_drv_init) {
+ platform_device_register_full(&qcom_cpuidle_info);
+ cpuidle_drv_init = true;
+ }
+
+ return 0;
+}
+
+static struct platform_driver spm_driver = {
+ .probe = spm_dev_probe,
+ .driver = {
+ .name = "saw",
+ .of_match_table = spm_match_table,
+ },
+};
+
+module_platform_driver(spm_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("SAW power controller driver");
+MODULE_ALIAS("saw");
diff --git a/include/soc/qcom/pm.h b/include/soc/qcom/pm.h
new file mode 100644
index 0000000..d9a56d7
--- /dev/null
+++ b/include/soc/qcom/pm.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (c) 2009-2014, The Linux Foundation. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __QCOM_PM_H
+#define __QCOM_PM_H
+
+enum pm_sleep_mode {
+ PM_SLEEP_MODE_STBY,
+ PM_SLEEP_MODE_RET,
+ PM_SLEEP_MODE_SPC,
+ PM_SLEEP_MODE_PC,
+ PM_SLEEP_MODE_NR,
+};
+
+struct qcom_cpu_pm_ops {
+ int (*standby)(void *data);
+ int (*spc)(void *data);
+};
+
+#endif /* __QCOM_PM_H */
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 03/10] qcom: spm: Add Subsystem Power Manager driver
2014-11-21 18:03 ` [PATCH v10 03/10] qcom: spm: Add Subsystem Power Manager driver Lina Iyer
@ 2014-11-26 20:00 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:00 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> +
> +static const struct platform_device_info qcom_cpuidle_info = {
nitpick, why two spaces between info and qcom here?
> + .name = "qcom_cpuidle",
> + .id = -1,
> + .data = &lpm_ops,
> + .size_data = sizeof(lpm_ops),
> +};
This struct could go on the stack too so that it doesn't lay around forever.
>
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("SAW power controller driver");
> +MODULE_ALIAS("saw");
"platform:saw" please. Namespacing aliases is good.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (2 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 03/10] qcom: spm: Add Subsystem Power Manager driver Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:01 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 05/10] arm: dts: qcom: Add power-controller device node for 8084 " Lina Iyer
` (6 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Each Krait CPU in the QCOM 8074/8974 SoC has an SAW power controller to
regulate the power to the cpu and aide the core in entering idle states.
Reference the SAW instance and associate the instance with the CPU core.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 26 +++++++++++++++++++++++++-
1 file changed, 25 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index e265ec1..80a4467 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -21,6 +21,7 @@
reg = <0>;
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
};
cpu@1 {
@@ -30,6 +31,7 @@
reg = <1>;
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
};
cpu@2 {
@@ -39,6 +41,7 @@
reg = <2>;
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
+ qcom,saw = <&saw2>;
};
cpu@3 {
@@ -48,6 +51,7 @@
reg = <3>;
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
+ qcom,saw = <&saw3>;
};
L2: l2-cache {
@@ -144,7 +148,27 @@
};
};
- saw_l2: regulator@f9012000 {
+ saw0: power-controller@f9089000 {
+ compatible = "qcom,msm8974-saw2-v2.1-cpu";
+ reg = <0xf9089000 0x1000>;
+ };
+
+ saw1: power-controller@f9099000 {
+ compatible = "qcom,msm8974-saw2-v2.1-cpu";
+ reg = <0xf9099000 0x1000>;
+ };
+
+ saw2: power-controller@f90a9000 {
+ compatible = "qcom,msm8974-saw2-v2.1-cpu";
+ reg = <0xf90a9000 0x1000>;
+ };
+
+ saw3: power-controller@f90b9000 {
+ compatible = "qcom,msm8974-saw2-v2.1-cpu";
+ reg = <0xf90b9000 0x1000>;
+ };
+
+ saw_l2: power-controller@f9012000 {
compatible = "qcom,saw2";
reg = <0xf9012000 0x1000>;
regulator;
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs
2014-11-21 18:03 ` [PATCH v10 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs Lina Iyer
@ 2014-11-26 20:01 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:01 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> @@ -144,7 +148,27 @@
> };
> };
>
> - saw_l2: regulator@f9012000 {
> + saw0: power-controller@f9089000 {
> + compatible = "qcom,msm8974-saw2-v2.1-cpu";
> + reg = <0xf9089000 0x1000>;
> + };
> +
> + saw1: power-controller@f9099000 {
> + compatible = "qcom,msm8974-saw2-v2.1-cpu";
> + reg = <0xf9099000 0x1000>;
> + };
> +
> + saw2: power-controller@f90a9000 {
> + compatible = "qcom,msm8974-saw2-v2.1-cpu";
> + reg = <0xf90a9000 0x1000>;
> + };
> +
> + saw3: power-controller@f90b9000 {
> + compatible = "qcom,msm8974-saw2-v2.1-cpu";
> + reg = <0xf90b9000 0x1000>;
> + };
All these nodes need to follow the binding and have two reg properties.
Please add the second one.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 05/10] arm: dts: qcom: Add power-controller device node for 8084 Krait CPUs
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (3 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 04/10] arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:05 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 06/10] arm: dts: qcom: Update power-controller device node for 8064 " Lina Iyer
` (5 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Each Krait CPU in the QCOM 8084 SoC has an SAW power controller to
regulate the power to the cpu and aide the core in entering idle states.
Reference the SAW instance and associate the instance with the CPU core.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-apq8084.dtsi | 26 +++++++++++++++++++++++++-
1 file changed, 25 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 1f130bc..4466b9e 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -21,6 +21,7 @@
enable-method = "qcom,kpss-acc-v2";
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
};
cpu@1 {
@@ -30,6 +31,7 @@
enable-method = "qcom,kpss-acc-v2";
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
};
cpu@2 {
@@ -39,6 +41,7 @@
enable-method = "qcom,kpss-acc-v2";
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
+ qcom,saw = <&saw2>;
};
cpu@3 {
@@ -48,6 +51,7 @@
enable-method = "qcom,kpss-acc-v2";
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
+ qcom,saw = <&saw3>;
};
L2: l2-cache {
@@ -144,7 +148,27 @@
};
};
- saw_l2: regulator@f9012000 {
+ saw0: power-controller@f9089000 {
+ compatible = "qcom,apq8084-saw2-v2.1-cpu";
+ reg = <0xf9089000 0x1000>;
+ };
+
+ saw1: power-controller@f9099000 {
+ compatible = "qcom,apq8084-saw2-v2.1-cpu";
+ reg = <0xf9099000 0x1000>;
+ };
+
+ saw2: power-controller@f90a9000 {
+ compatible = "qcom,apq8084-saw2-v2.1-cpu";
+ reg = <0xf90a9000 0x1000>;
+ };
+
+ saw3: power-controller@f90b9000 {
+ compatible = "qcom,apq8084-saw2-v2.1-cpu";
+ reg = <0xf90b9000 0x1000>;
+ };
+
+ saw_l2: power-controller@f9012000 {
compatible = "qcom,saw2";
reg = <0xf9012000 0x1000>;
regulator;
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 05/10] arm: dts: qcom: Add power-controller device node for 8084 Krait CPUs
2014-11-21 18:03 ` [PATCH v10 05/10] arm: dts: qcom: Add power-controller device node for 8084 " Lina Iyer
@ 2014-11-26 20:05 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:05 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> @@ -144,7 +148,27 @@
> };
> };
>
> - saw_l2: regulator@f9012000 {
> + saw0: power-controller@f9089000 {
> + compatible = "qcom,apq8084-saw2-v2.1-cpu";
> + reg = <0xf9089000 0x1000>;
> + };
> +
> + saw1: power-controller@f9099000 {
> + compatible = "qcom,apq8084-saw2-v2.1-cpu";
> + reg = <0xf9099000 0x1000>;
> + };
> +
> + saw2: power-controller@f90a9000 {
> + compatible = "qcom,apq8084-saw2-v2.1-cpu";
> + reg = <0xf90a9000 0x1000>;
> + };
> +
> + saw3: power-controller@f90b9000 {
> + compatible = "qcom,apq8084-saw2-v2.1-cpu";
> + reg = <0xf90b9000 0x1000>;
> + };
>
Same comment as in patch 4, please add the second reg property.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 06/10] arm: dts: qcom: Update power-controller device node for 8064 Krait CPUs
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (4 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 05/10] arm: dts: qcom: Add power-controller device node for 8084 " Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:06 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus Lina Iyer
` (4 subsequent siblings)
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Update the SAW2 DT bindings to add qcom,apq8064-saw2-v1.1-cpu compatible
binding string to configure SPM registers and allow the SPM to put the
core in deeper idle states when the core is idle.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index b3154c0..9fd24bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -139,26 +139,26 @@
reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
};
- saw0: regulator@2089000 {
- compatible = "qcom,saw2";
+ saw0: power-controller@2089000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw1: regulator@2099000 {
- compatible = "qcom,saw2";
+ saw1: power-controller@2099000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw2: regulator@20a9000 {
- compatible = "qcom,saw2";
+ saw2: power-controller@20a9000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw3: regulator@20b9000 {
- compatible = "qcom,saw2";
+ saw3: power-controller@20b9000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 06/10] arm: dts: qcom: Update power-controller device node for 8064 Krait CPUs
2014-11-21 18:03 ` [PATCH v10 06/10] arm: dts: qcom: Update power-controller device node for 8064 " Lina Iyer
@ 2014-11-26 20:06 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:06 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> Update the SAW2 DT bindings to add qcom,apq8064-saw2-v1.1-cpu compatible
> binding string to configure SPM registers and allow the SPM to put the
> core in deeper idle states when the core is idle.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (5 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 06/10] arm: dts: qcom: Update power-controller device node for 8064 " Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 10:04 ` Daniel Lezcano
2014-11-26 17:59 ` Lorenzo Pieralisi
[not found] ` <1416593037-27527-1-git-send-email-lina.iyer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
` (3 subsequent siblings)
10 siblings, 2 replies; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Add cpuidle driver interface to allow cpus to go into C-States. Use the
cpuidle DT interface, common across ARM architectures, to provide the
idle state information to the cpuidle framework.
Supported modes at this time are Standby and Standalone Power Collapse.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
.../bindings/arm/msm/qcom,idle-state.txt | 81 ++++++++++++++++++++++
drivers/cpuidle/Kconfig.arm | 7 ++
drivers/cpuidle/Makefile | 1 +
drivers/cpuidle/cpuidle-qcom.c | 72 +++++++++++++++++++
4 files changed, 161 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
create mode 100644 drivers/cpuidle/cpuidle-qcom.c
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
new file mode 100644
index 0000000..ae1b07f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
@@ -0,0 +1,81 @@
+QCOM Idle States for cpuidle driver
+
+ARM provides idle-state node to define the cpuidle states, as defined in [1].
+cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
+states. Idle states have different enter/exit latency and residency values.
+The idle states supported by the QCOM SoC are defined as -
+
+ * Standby
+ * Retention
+ * Standalone Power Collapse (Standalone PC or SPC)
+ * Power Collapse (PC)
+
+Standby: Standby does a little more in addition to architectural clock gating.
+When the WFI instruction is executed the ARM core would gate its internal
+clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
+trigger to execute the SPM state machine. The SPM state machine waits for the
+interrupt to trigger the core back in to active. This triggers the cache
+hierarchy to enter standby states, when all cpus are idle. An interrupt brings
+the SPM state machine out of its wait, the next step is to ensure that the
+cache hierarchy is also out of standby, and then the cpu is allowed to resume
+execution.
+
+Retention: Retention is a low power state where the core is clock gated and
+the memory and the registers associated with the core are retained. The
+voltage may be reduced to the minimum value needed to keep the processor
+registers active. The SPM should be configured to execute the retention
+sequence and would wait for interrupt, before restoring the cpu to execution
+state. Retention may have a slightly higher latency than Standby.
+
+Standalone PC: A cpu can power down and warmboot if there is a sufficient time
+between the time it enters idle and the next known wake up. SPC mode is used
+to indicate a core entering a power down state without consulting any other
+cpu or the system resources. This helps save power only on that core. The SPM
+sequence for this idle state is programmed to power down the supply to the
+core, wait for the interrupt, restore power to the core, and ensure the
+system state including cache hierarchy is ready before allowing core to
+resume. Applying power and resetting the core causes the core to warmboot
+back into Elevation Level (EL) which trampolines the control back to the
+kernel. Entering a power down state for the cpu, needs to be done by trapping
+into a EL. Failing to do so, would result in a crash enforced by the warm boot
+code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
+be flushed in s/w, before powering down the core.
+
+Power Collapse: This state is similar to the SPC mode, but distinguishes
+itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
+modes. In a hierarchical power domain SoC, this means L2 and other caches can
+be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
+voltages reduced, provided all cpus enter this state. Since the span of low
+power modes possible at this state is vast, the exit latency and the residency
+of this low power mode would be considered high even though at a cpu level,
+this essentially is cpu power down. The SPM in this state also may handshake
+with the Resource power manager processor in the SoC to indicate a complete
+application processor subsystem shut down.
+
+The idle-state for QCOM SoCs are distinguished by the compatible property of
+the idle-states device node.
+The devicetree representation of the idle state should be -
+
+Required properties:
+
+- compatible: Must be one of -
+ "qcom,idle-state-stby",
+ "qcom,idle-state-ret",
+ "qcom,idle-state-spc",
+ "qcom,idle-state-pc",
+ and "arm,idle-state".
+
+Other required and optional properties are specified in [1].
+
+Example:
+
+ idle-states {
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <150>;
+ exit-latency-us = <200>;
+ min-residency-us = <2000>;
+ };
+ };
+
+[1]. Documentation/devicetree/bindings/arm/idle-states.txt
diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
index 8c16ab2..e98993c 100644
--- a/drivers/cpuidle/Kconfig.arm
+++ b/drivers/cpuidle/Kconfig.arm
@@ -63,3 +63,10 @@ config ARM_MVEBU_V7_CPUIDLE
depends on ARCH_MVEBU
help
Select this to enable cpuidle on Armada 370, 38x and XP processors.
+
+config ARM_QCOM_CPUIDLE
+ bool "CPU Idle drivers for Qualcomm processors"
+ depends on ARCH_QCOM
+ select DT_IDLE_STATES
+ help
+ Select this to enable cpuidle for QCOM processors
diff --git a/drivers/cpuidle/Makefile b/drivers/cpuidle/Makefile
index 4d177b9..6c222d5 100644
--- a/drivers/cpuidle/Makefile
+++ b/drivers/cpuidle/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_ARM_ZYNQ_CPUIDLE) += cpuidle-zynq.o
obj-$(CONFIG_ARM_U8500_CPUIDLE) += cpuidle-ux500.o
obj-$(CONFIG_ARM_AT91_CPUIDLE) += cpuidle-at91.o
obj-$(CONFIG_ARM_EXYNOS_CPUIDLE) += cpuidle-exynos.o
+obj-$(CONFIG_ARM_QCOM_CPUIDLE) += cpuidle-qcom.o
###############################################################################
# MIPS drivers
diff --git a/drivers/cpuidle/cpuidle-qcom.c b/drivers/cpuidle/cpuidle-qcom.c
new file mode 100644
index 0000000..1c1dcbc
--- /dev/null
+++ b/drivers/cpuidle/cpuidle-qcom.c
@@ -0,0 +1,72 @@
+/*
+ * Copyright (c) 2014, Linaro Limited.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/cpuidle.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <soc/qcom/pm.h>
+#include "dt_idle_states.h"
+
+static struct qcom_cpu_pm_ops *lpm_ops;
+
+static int qcom_cpu_stby(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv, int index)
+{
+ lpm_ops->standby(NULL);
+
+ return index;
+}
+
+static int qcom_cpu_spc(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv, int index)
+{
+ lpm_ops->spc(NULL);
+
+ return index;
+}
+
+static struct cpuidle_driver qcom_cpuidle_driver = {
+ .name = "qcom_cpuidle",
+};
+
+static const struct of_device_id qcom_idle_state_match[] = {
+ { .compatible = "qcom,idle-state-stby", .data = qcom_cpu_stby},
+ { .compatible = "qcom,idle-state-spc", .data = qcom_cpu_spc },
+ { },
+};
+
+static int qcom_cpuidle_probe(struct platform_device *pdev)
+{
+ struct cpuidle_driver *drv = &qcom_cpuidle_driver;
+ int ret;
+
+ lpm_ops = pdev->dev.platform_data;
+
+ /* Probe for other states, including standby */
+ ret = dt_init_idle_driver(drv, qcom_idle_state_match, 0);
+ if (ret < 0)
+ return ret;
+
+ return cpuidle_register(drv, NULL);
+}
+
+static struct platform_driver qcom_cpuidle_plat_driver = {
+ .probe = qcom_cpuidle_probe,
+ .driver = {
+ .name = "qcom_cpuidle",
+ },
+};
+
+module_platform_driver(qcom_cpuidle_plat_driver);
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-21 18:03 ` [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus Lina Iyer
@ 2014-11-26 10:04 ` Daniel Lezcano
2014-11-26 19:43 ` Kevin Hilman
2014-11-26 17:59 ` Lorenzo Pieralisi
1 sibling, 1 reply; 28+ messages in thread
From: Daniel Lezcano @ 2014-11-26 10:04 UTC (permalink / raw)
To: Lina Iyer, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 07:03 PM, Lina Iyer wrote:
> Add cpuidle driver interface to allow cpus to go into C-States. Use the
> cpuidle DT interface, common across ARM architectures, to provide the
> idle state information to the cpuidle framework.
>
> Supported modes at this time are Standby and Standalone Power Collapse.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
One nit and one comment below. Other than that:
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ ... ]
> +static int qcom_cpu_stby(struct cpuidle_device *dev,
> + struct cpuidle_driver *drv, int index)
> +{
> + lpm_ops->standby(NULL);
In my last comment I was referring about a check for entering
successfully the idle state:
if (lpm_ops->standby(NULL))
return -1;
> + return index;
> +}
> +
> +static int qcom_cpu_spc(struct cpuidle_device *dev,
> + struct cpuidle_driver *drv, int index)
> +{
> + lpm_ops->spc(NULL);
> +
> + return index;
> +}
> +
> +static struct cpuidle_driver qcom_cpuidle_driver = {
> + .name = "qcom_cpuidle",
> +};
> +
> +static const struct of_device_id qcom_idle_state_match[] = {
> + { .compatible = "qcom,idle-state-stby", .data = qcom_cpu_stby},
^^^^
a missing space right before the closing bracket.
> + { .compatible = "qcom,idle-state-spc", .data = qcom_cpu_spc },
> + { },
> +};
> +
Thanks!
-- Daniel
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-26 10:04 ` Daniel Lezcano
@ 2014-11-26 19:43 ` Kevin Hilman
2014-11-27 10:23 ` Lorenzo Pieralisi
0 siblings, 1 reply; 28+ messages in thread
From: Kevin Hilman @ 2014-11-26 19:43 UTC (permalink / raw)
To: Daniel Lezcano
Cc: Lina Iyer, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
Daniel Lezcano <daniel.lezcano@linaro.org> writes:
> On 11/21/2014 07:03 PM, Lina Iyer wrote:
>> Add cpuidle driver interface to allow cpus to go into C-States. Use the
>> cpuidle DT interface, common across ARM architectures, to provide the
>> idle state information to the cpuidle framework.
>>
>> Supported modes at this time are Standby and Standalone Power Collapse.
>>
>> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
>
> One nit and one comment below. Other than that:
>
> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
>
> [ ... ]
>
>> +static int qcom_cpu_stby(struct cpuidle_device *dev,
>> + struct cpuidle_driver *drv, int index)
>> +{
>> + lpm_ops->standby(NULL);
>
> In my last comment I was referring about a check for entering
> successfully the idle state:
>
> if (lpm_ops->standby(NULL))
> return -1;
>
>> + return index;
>> +}
>> +
>> +static int qcom_cpu_spc(struct cpuidle_device *dev,
>> + struct cpuidle_driver *drv, int index)
>> +{
>> + lpm_ops->spc(NULL);
>> +
>> + return index;
Similar to Daniel's comment above. if lpm_ops->spc() fails, do you want
to fall back to standby.
Hmm, using the DT idle states, it doesn't look as straight forward as it
used to be to fall back to a "safe state."
Kevin
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-26 19:43 ` Kevin Hilman
@ 2014-11-27 10:23 ` Lorenzo Pieralisi
0 siblings, 0 replies; 28+ messages in thread
From: Lorenzo Pieralisi @ 2014-11-27 10:23 UTC (permalink / raw)
To: Kevin Hilman
Cc: Daniel Lezcano, Lina Iyer, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, msivasub, devicetree
Hi Kevin,
On Wed, Nov 26, 2014 at 07:43:01PM +0000, Kevin Hilman wrote:
> Daniel Lezcano <daniel.lezcano@linaro.org> writes:
>
> > On 11/21/2014 07:03 PM, Lina Iyer wrote:
> >> Add cpuidle driver interface to allow cpus to go into C-States. Use the
> >> cpuidle DT interface, common across ARM architectures, to provide the
> >> idle state information to the cpuidle framework.
> >>
> >> Supported modes at this time are Standby and Standalone Power Collapse.
> >>
> >> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
> >
> > One nit and one comment below. Other than that:
> >
> > Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
> >
> > [ ... ]
> >
> >> +static int qcom_cpu_stby(struct cpuidle_device *dev,
> >> + struct cpuidle_driver *drv, int index)
> >> +{
> >> + lpm_ops->standby(NULL);
> >
> > In my last comment I was referring about a check for entering
> > successfully the idle state:
> >
> > if (lpm_ops->standby(NULL))
> > return -1;
> >
> >> + return index;
> >> +}
> >> +
> >> +static int qcom_cpu_spc(struct cpuidle_device *dev,
> >> + struct cpuidle_driver *drv, int index)
> >> +{
> >> + lpm_ops->spc(NULL);
> >> +
> >> + return index;
>
> Similar to Daniel's comment above. if lpm_ops->spc() fails, do you want
> to fall back to standby.
>
> Hmm, using the DT idle states, it doesn't look as straight forward as it
> used to be to fall back to a "safe state."
What do you mean by "safe state" ? As in coupled idle states ?
It is just for me to understand why DT makes things more complicated :)
If the idle state enter fails it might also be because there is an
aborted power down owing to eg pending IRQ, there would be no reason
why you would revert to standby instead of going back to the kernel, so
error code must be explicit at least in that respect.
Thanks,
Lorenzo
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-21 18:03 ` [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus Lina Iyer
2014-11-26 10:04 ` Daniel Lezcano
@ 2014-11-26 17:59 ` Lorenzo Pieralisi
2014-11-26 21:03 ` Lina Iyer
1 sibling, 1 reply; 28+ messages in thread
From: Lorenzo Pieralisi @ 2014-11-26 17:59 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, msivasub, devicetree
On Fri, Nov 21, 2014 at 06:03:54PM +0000, Lina Iyer wrote:
> Add cpuidle driver interface to allow cpus to go into C-States. Use the
"idle states" please.
> cpuidle DT interface, common across ARM architectures, to provide the
> idle state information to the cpuidle framework.
>
> Supported modes at this time are Standby and Standalone Power Collapse.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
> ---
> .../bindings/arm/msm/qcom,idle-state.txt | 81 ++++++++++++++++++++++
> drivers/cpuidle/Kconfig.arm | 7 ++
> drivers/cpuidle/Makefile | 1 +
> drivers/cpuidle/cpuidle-qcom.c | 72 +++++++++++++++++++
> 4 files changed, 161 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
> create mode 100644 drivers/cpuidle/cpuidle-qcom.c
>
> diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
> new file mode 100644
> index 0000000..ae1b07f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
> @@ -0,0 +1,81 @@
> +QCOM Idle States for cpuidle driver
> +
> +ARM provides idle-state node to define the cpuidle states, as defined in [1].
> +cpuidle-qcom is the cpuidle driver for Qualcomm SoCs and uses these idle
> +states. Idle states have different enter/exit latency and residency values.
> +The idle states supported by the QCOM SoC are defined as -
> +
> + * Standby
> + * Retention
> + * Standalone Power Collapse (Standalone PC or SPC)
> + * Power Collapse (PC)
> +
> +Standby: Standby does a little more in addition to architectural clock gating.
> +When the WFI instruction is executed the ARM core would gate its internal
> +clocks. In addition to gating the clocks, QCOM cpus use this instruction as a
> +trigger to execute the SPM state machine. The SPM state machine waits for the
> +interrupt to trigger the core back in to active. This triggers the cache
> +hierarchy to enter standby states, when all cpus are idle. An interrupt brings
> +the SPM state machine out of its wait, the next step is to ensure that the
> +cache hierarchy is also out of standby, and then the cpu is allowed to resume
> +execution.
> +
> +Retention: Retention is a low power state where the core is clock gated and
> +the memory and the registers associated with the core are retained. The
> +voltage may be reduced to the minimum value needed to keep the processor
> +registers active. The SPM should be configured to execute the retention
> +sequence and would wait for interrupt, before restoring the cpu to execution
> +state. Retention may have a slightly higher latency than Standby.
> +
> +Standalone PC: A cpu can power down and warmboot if there is a sufficient time
> +between the time it enters idle and the next known wake up. SPC mode is used
> +to indicate a core entering a power down state without consulting any other
> +cpu or the system resources. This helps save power only on that core. The SPM
> +sequence for this idle state is programmed to power down the supply to the
> +core, wait for the interrupt, restore power to the core, and ensure the
> +system state including cache hierarchy is ready before allowing core to
> +resume. Applying power and resetting the core causes the core to warmboot
> +back into Elevation Level (EL) which trampolines the control back to the
> +kernel. Entering a power down state for the cpu, needs to be done by trapping
> +into a EL. Failing to do so, would result in a crash enforced by the warm boot
> +code in the EL for the SoC. On SoCs with write-back L1 cache, the cache has to
> +be flushed in s/w, before powering down the core.
> +
> +Power Collapse: This state is similar to the SPC mode, but distinguishes
> +itself in that the cpu acknowledges and permits the SoC to enter deeper sleep
> +modes. In a hierarchical power domain SoC, this means L2 and other caches can
> +be flushed, system bus, clocks - lowered, and SoC main XO clock gated and
> +voltages reduced, provided all cpus enter this state. Since the span of low
> +power modes possible at this state is vast, the exit latency and the residency
> +of this low power mode would be considered high even though at a cpu level,
> +this essentially is cpu power down. The SPM in this state also may handshake
> +with the Resource power manager processor in the SoC to indicate a complete
> +application processor subsystem shut down.
> +
> +The idle-state for QCOM SoCs are distinguished by the compatible property of
> +the idle-states device node.
> +The devicetree representation of the idle state should be -
> +
> +Required properties:
> +
> +- compatible: Must be one of -
> + "qcom,idle-state-stby",
> + "qcom,idle-state-ret",
> + "qcom,idle-state-spc",
> + "qcom,idle-state-pc",
> + and "arm,idle-state".
> +
> +Other required and optional properties are specified in [1].
> +
> +Example:
> +
> + idle-states {
> + CPU_SPC: spc {
> + compatible = "qcom,idle-state-spc", "arm,idle-state";
> + entry-latency-us = <150>;
> + exit-latency-us = <200>;
> + min-residency-us = <2000>;
> + };
> + };
> +
> +[1]. Documentation/devicetree/bindings/arm/idle-states.txt
> diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
> index 8c16ab2..e98993c 100644
> --- a/drivers/cpuidle/Kconfig.arm
> +++ b/drivers/cpuidle/Kconfig.arm
> @@ -63,3 +63,10 @@ config ARM_MVEBU_V7_CPUIDLE
> depends on ARCH_MVEBU
> help
> Select this to enable cpuidle on Armada 370, 38x and XP processors.
> +
> +config ARM_QCOM_CPUIDLE
> + bool "CPU Idle drivers for Qualcomm processors"
> + depends on ARCH_QCOM
> + select DT_IDLE_STATES
> + help
> + Select this to enable cpuidle for QCOM processors
> diff --git a/drivers/cpuidle/Makefile b/drivers/cpuidle/Makefile
> index 4d177b9..6c222d5 100644
> --- a/drivers/cpuidle/Makefile
> +++ b/drivers/cpuidle/Makefile
> @@ -17,6 +17,7 @@ obj-$(CONFIG_ARM_ZYNQ_CPUIDLE) += cpuidle-zynq.o
> obj-$(CONFIG_ARM_U8500_CPUIDLE) += cpuidle-ux500.o
> obj-$(CONFIG_ARM_AT91_CPUIDLE) += cpuidle-at91.o
> obj-$(CONFIG_ARM_EXYNOS_CPUIDLE) += cpuidle-exynos.o
> +obj-$(CONFIG_ARM_QCOM_CPUIDLE) += cpuidle-qcom.o
>
> ###############################################################################
> # MIPS drivers
> diff --git a/drivers/cpuidle/cpuidle-qcom.c b/drivers/cpuidle/cpuidle-qcom.c
> new file mode 100644
> index 0000000..1c1dcbc
> --- /dev/null
> +++ b/drivers/cpuidle/cpuidle-qcom.c
> @@ -0,0 +1,72 @@
> +/*
> + * Copyright (c) 2014, Linaro Limited.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/cpuidle.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +
> +#include <soc/qcom/pm.h>
> +#include "dt_idle_states.h"
> +
> +static struct qcom_cpu_pm_ops *lpm_ops;
> +
> +static int qcom_cpu_stby(struct cpuidle_device *dev,
> + struct cpuidle_driver *drv, int index)
> +{
> + lpm_ops->standby(NULL);
> +
> + return index;
> +}
> +
> +static int qcom_cpu_spc(struct cpuidle_device *dev,
> + struct cpuidle_driver *drv, int index)
> +{
> + lpm_ops->spc(NULL);
> +
> + return index;
> +}
Check power down functions return codes please as Daniel already
pointed out, this might skew stats and prevent debugging.
> +static struct cpuidle_driver qcom_cpuidle_driver = {
> + .name = "qcom_cpuidle",
> +};
> +
> +static const struct of_device_id qcom_idle_state_match[] = {
> + { .compatible = "qcom,idle-state-stby", .data = qcom_cpu_stby},
> + { .compatible = "qcom,idle-state-spc", .data = qcom_cpu_spc },
> + { },
> +};
> +
> +static int qcom_cpuidle_probe(struct platform_device *pdev)
> +{
> + struct cpuidle_driver *drv = &qcom_cpuidle_driver;
> + int ret;
> +
> + lpm_ops = pdev->dev.platform_data;
> +
> + /* Probe for other states, including standby */
> + ret = dt_init_idle_driver(drv, qcom_idle_state_match, 0);
> + if (ret < 0)
> + return ret;
> +
> + return cpuidle_register(drv, NULL);
> +}
> +
> +static struct platform_driver qcom_cpuidle_plat_driver = {
> + .probe = qcom_cpuidle_probe,
> + .driver = {
> + .name = "qcom_cpuidle",
> + },
> +};
> +
> +module_platform_driver(qcom_cpuidle_plat_driver);
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
^ permalink raw reply [flat|nested] 28+ messages in thread* Re: [PATCH v10 07/10] qcom: cpuidle: Add cpuidle driver for QCOM cpus
2014-11-26 17:59 ` Lorenzo Pieralisi
@ 2014-11-26 21:03 ` Lina Iyer
0 siblings, 0 replies; 28+ messages in thread
From: Lina Iyer @ 2014-11-26 21:03 UTC (permalink / raw)
To: Lorenzo Pieralisi
Cc: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, msivasub, devicetree
On Wed, Nov 26 2014 at 10:59 -0700, Lorenzo Pieralisi wrote:
>On Fri, Nov 21, 2014 at 06:03:54PM +0000, Lina Iyer wrote:
>> Add cpuidle driver interface to allow cpus to go into C-States. Use the
>
>"idle states" please.
>
Sorry. Done.
>Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
>--
>To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 28+ messages in thread
[parent not found: <1416593037-27527-1-git-send-email-lina.iyer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>]
* [PATCH v10 08/10] arm: dts: qcom: Add idle states device nodes for 8074
[not found] ` <1416593037-27527-1-git-send-email-lina.iyer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:15 ` Stephen Boyd
0 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano-QSEj5FYQhm4dnm+yROfE0A,
khilman-QSEj5FYQhm4dnm+yROfE0A, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
galak-sgV2jX0FEOL9JmXXK+q4OQ,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-pm-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: lorenzo.pieralisi-5wv7dgnIgG8, msivasub-sgV2jX0FEOL9JmXXK+q4OQ,
devicetree-u79uwXL29TY76Z2rM5mHXA, Lina Iyer
Add ARM common idle states device bindings for cpuidle support for APQ
8074/8974.
Support Standby and Standalone power collapse (power down that does not
affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/qcom-msm8974.dtsi | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 80a4467..e68b40f 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -22,6 +22,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@1 {
@@ -32,6 +33,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@2 {
@@ -42,6 +44,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@3 {
@@ -52,6 +55,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
L2: l2-cache {
@@ -59,6 +63,22 @@
cache-level = <2>;
qcom,saw = <&saw_l2>;
};
+
+ idle-states {
+ CPU_STBY: standby {
+ compatible = "qcom,idle-state-stby", "arm,idle-state";
+ entry-latency-us = <1>;
+ exit-latency-us = <1>;
+ min-residency-us = <2>;
+ };
+
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <150>;
+ exit-latency-us = <200>;
+ min-residency-us = <2000>;
+ };
+ };
};
cpu-pmu {
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 08/10] arm: dts: qcom: Add idle states device nodes for 8074
2014-11-21 18:03 ` [PATCH v10 08/10] arm: dts: qcom: Add idle states device nodes for 8074 Lina Iyer
@ 2014-11-26 20:15 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:15 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> Add ARM common idle states device bindings for cpuidle support for APQ
> 8074/8974.
>
> Support Standby and Standalone power collapse (power down that does not
> affect any SoC idle states) for each cpu.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 09/10] arm: dts: qcom: Add idle states device nodes for 8084
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (7 preceding siblings ...)
[not found] ` <1416593037-27527-1-git-send-email-lina.iyer-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:16 ` Stephen Boyd
2014-11-21 18:03 ` [PATCH v10 10/10] arm: dts: qcom: Add idle state device nodes for 8064 Lina Iyer
2014-11-25 19:11 ` [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Add ARM common idle states device bindings for cpuidle support for APQ
8084.
Support standby and standalone power collapse (power down that does not
affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-apq8084.dtsi | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 4466b9e..207be15 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -22,6 +22,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@1 {
@@ -32,6 +33,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@2 {
@@ -42,6 +44,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@3 {
@@ -52,6 +55,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
L2: l2-cache {
@@ -59,6 +63,22 @@
cache-level = <2>;
qcom,saw = <&saw_l2>;
};
+
+ idle-states {
+ CPU_STBY: standby {
+ compatible = "qcom,idle-state-stby", "arm,idle-state";
+ entry-latency-us = <1>;
+ exit-latency-us = <1>;
+ min-residency-us = <2>;
+ };
+
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <150>;
+ exit-latency-us = <200>;
+ min-residency-us = <2000>;
+ };
+ };
};
cpu-pmu {
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 09/10] arm: dts: qcom: Add idle states device nodes for 8084
2014-11-21 18:03 ` [PATCH v10 09/10] arm: dts: qcom: Add idle states device nodes for 8084 Lina Iyer
@ 2014-11-26 20:16 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:16 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> Add ARM common idle states device bindings for cpuidle support for APQ
> 8084.
>
> Support standby and standalone power collapse (power down that does not
> affect any SoC idle states) for each cpu.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* [PATCH v10 10/10] arm: dts: qcom: Add idle state device nodes for 8064
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (8 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 09/10] arm: dts: qcom: Add idle states device nodes for 8084 Lina Iyer
@ 2014-11-21 18:03 ` Lina Iyer
2014-11-26 20:18 ` Stephen Boyd
2014-11-25 19:11 ` [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
10 siblings, 1 reply; 28+ messages in thread
From: Lina Iyer @ 2014-11-21 18:03 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree, Lina Iyer
Add ARM common idle state device bindings for cpuidle support for APQ
8064.
Support Standby and Standalone power collapse (power down that does not
affect any SoC idle states) for each cpu.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 9fd24bc..3eaf242 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -23,6 +23,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@1 {
@@ -33,6 +34,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@2 {
@@ -43,6 +45,7 @@
next-level-cache = <&L2>;
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
cpu@3 {
@@ -53,12 +56,30 @@
next-level-cache = <&L2>;
qcom,acc = <&acc3>;
qcom,saw = <&saw3>;
+ cpu-idle-states = <&CPU_STBY &CPU_SPC>;
};
L2: l2-cache {
compatible = "cache";
cache-level = <2>;
};
+
+ idle-states {
+ CPU_STBY: standby {
+ compatible = "qcom,idle-state-stby", "arm,idle-state";
+ entry-latency-us = <1>;
+ exit-latency-us = <1>;
+ min-residency-us = <2>;
+ };
+
+ CPU_SPC: spc {
+ compatible = "qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <400>;
+ exit-latency-us = <900>;
+ min-residency-us = <3000>;
+ };
+ };
+
};
cpu-pmu {
--
2.1.0
^ permalink raw reply related [flat|nested] 28+ messages in thread* Re: [PATCH v10 10/10] arm: dts: qcom: Add idle state device nodes for 8064
2014-11-21 18:03 ` [PATCH v10 10/10] arm: dts: qcom: Add idle state device nodes for 8064 Lina Iyer
@ 2014-11-26 20:18 ` Stephen Boyd
0 siblings, 0 replies; 28+ messages in thread
From: Stephen Boyd @ 2014-11-26 20:18 UTC (permalink / raw)
To: Lina Iyer
Cc: daniel.lezcano, khilman, galak, linux-arm-msm, linux-pm,
linux-arm-kernel, lorenzo.pieralisi, msivasub, devicetree
On 11/21/2014 10:03 AM, Lina Iyer wrote:
> Add ARM common idle state device bindings for cpuidle support for APQ
> 8064.
>
> Support Standby and Standalone power collapse (power down that does not
> affect any SoC idle states) for each cpu.
>
> Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
With nitpick addressed:
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
> @@ -53,12 +56,30 @@
> next-level-cache = <&L2>;
> qcom,acc = <&acc3>;
> qcom,saw = <&saw3>;
> + cpu-idle-states = <&CPU_STBY &CPU_SPC>;
> };
>
> L2: l2-cache {
> compatible = "cache";
> cache-level = <2>;
> };
> +
> + idle-states {
> + CPU_STBY: standby {
> + compatible = "qcom,idle-state-stby", "arm,idle-state";
> + entry-latency-us = <1>;
> + exit-latency-us = <1>;
> + min-residency-us = <2>;
> + };
> +
> + CPU_SPC: spc {
> + compatible = "qcom,idle-state-spc", "arm,idle-state";
> + entry-latency-us = <400>;
> + exit-latency-us = <900>;
> + min-residency-us = <3000>;
> + };
> + };
> +
Nitpick, no need for blank line here.
> };
>
> cpu-pmu {
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084
2014-11-21 18:03 [PATCH v10 00/10] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
` (9 preceding siblings ...)
2014-11-21 18:03 ` [PATCH v10 10/10] arm: dts: qcom: Add idle state device nodes for 8064 Lina Iyer
@ 2014-11-25 19:11 ` Lina Iyer
10 siblings, 0 replies; 28+ messages in thread
From: Lina Iyer @ 2014-11-25 19:11 UTC (permalink / raw)
To: daniel.lezcano, khilman, sboyd, galak, linux-arm-msm, linux-pm,
linux-arm-kernel
Cc: lorenzo.pieralisi, msivasub, devicetree
Any comments?
On Fri, Nov 21 2014 at 11:04 -0700, Lina Iyer wrote:
>Changes since v9:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg11714.html ]
>- Address review comments on v9
>Dependent patchsets -
> https://lkml.org/lkml/2014/8/4/767
> http://www.spinics.net/lists/linux-arm-msm/msg10799.html
> http://www.spinics.net/lists/linux-arm-msm/msg10795.html
>
>Changes since v8:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg11473.html ]
>- Flatten out the file structure - merge pm.c into spm.c after discussions
>- Add a new function to set warm boot address, in scm-boot.c
>- Support for 8064 (New)
>- Tested on 8074, 8084. 8064 was tested with a WIP tree
>- Address review comments from v8
>- Looking into possiblility of initializing the cpuidle device for a cpu,
>only when the corresponding spm device is probed successfully.
>
>Changes since v7:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg11199.html ]
>- Address review comments
>- Tested on 8974 but not 8084
>- WFI renamed to Standby
>- Update commit text with original author and link to the downstream tree
>
>Changes since v6:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg11012.html ]
>- SPM device nodes merged with existing SAW DT nodes
>- SPM register information is handled within the driver
>- Clean up from using 'msm' to 'qcom'
> - Shorten some enumerations as well
>- Review comments from v6 addressed
>- New: Support for 8084 SoC
> - Not tested. I do not have a board with this SoC, but the SPM
> configuration should be identical for WFI and SPC
>
>Changes since v5:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10559.html ]
>- Merge spm-devices.c and spm.c into one file and one patch
> - Simplify implementation of the driver.
> - Update documentation mapping the DT properties with corresponding
> SPM register information.
>- Removed scm-boot changes for quad core warmboot, its has been pulled in.
>
>Changes since v4:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10327.html ]
>- Update to the v8 of ARM generic idle states patches
>- Use platform device model for cpuidle-qcom
>- Clean up msm-pm.c to remove unnecessary include files and functions
>- Update commit text and documentation for all idle states
>- Remove scm-boot relocate patch from this series, submitted earlier
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10518.html ]
>
>Changes since v3:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10288.html ]
>- Fix CONFIG_QCOM_PM Kconfig as bool
>- More clean ups in spm.c and spm-devices.c
> - Removed and re-organized data structures to make initialization simple
> - Remove export of sequence flush functions
> - Updated commit text
> - Comments for use of barriers.
>- Rebase on top of 3.17-rc1
>
>Changes since v2:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10148.html ]
>- Prune all the drivers to support basic WFI and power down cpuidle
> functionality. Remove debug code.
>- Integrate KConfig changes into the drivers' patches.
>- Use Lorenzo's ARM idle-states patches as the basis for reading cpuidle
> c-states from DT.
> [ http://marc.info/?l=linux-pm&m=140794514812383&w=2 ]
>- Incorporate review comments
>- Rebase on top of 3.16
>
>Changes since v1/RFC:
>[ https://www.mail-archive.com/linux-arm-msm@vger.kernel.org/msg10065.html ]
>- Remove hotplug from the patch series. Will submit it separately.
>- Fix SPM drivers per the review comments
>- Modify patch sequence to compile SPM drivers independent of msm-pm, so as to
> allow wfi() calls to use SPM even without SoC interface driver.
>
>8074/8084/8064 like any ARM SoC can do architectural clock gating, that helps save
>on power, but not enough of leakage power. Leakage power of the SoC can be
>further reduced by turning off power to the core. To aid this, every core (cpu
>and L2) is accompanied by a Sub-system Power Manager (SPM), that can be
>configured to indicate the low power mode, the core would be put into and the
>SPM programs the peripheral h/w accordingly to enter low power and turn off the
>power rail to the core.
>
>The idle invocation hierarchy -
>
>CPUIDLE
> |
> cpuidle-qcom.c [CPUIdle driver]
> |
> ------> spm.c [SPM driver]
> |
> ------> scm-boot.c [SCM interface layer]
> |
>------------------------|--------------------------
>(EL) Secure Monitor Code
> |
> |
> wfi();
>------------------------|--------------------------
>(HW) [CPU] {clock gate}
> |
> -----> [SPM] {statemachine}
>
>
>The patchset does the following -
>
>- Introduce the SPM driver to control power to the core
>- Add device bindings for 8974, 8084, 8064 CPU SPM devices
>- Add cpuidle driver for QCOM cpus, using ARM generic idle state definitions.
>- Add device bindings for 8974, 8084, 8064 idle-states - WFI and SPC
>
>Thanks,
>Lina
>
>Lina Iyer (10):
> qom: scm: Move scm-boot files to drivers/soc/qcom/ and
> include/soc/qcom
> qcom: scm: Add SCM warmboot support for quad core SoCs
> qcom: spm: Add Subsystem Power Manager driver
> arm: dts: qcom: Add power-controller device node for 8074 Krait CPUs
> arm: dts: qcom: Add power-controller device node for 8084 Krait CPUs
> arm: dts: qcom: Update power-controller device node for 8064 Krait
> CPUs
> qcom: cpuidle: Add cpuidle driver for QCOM cpus
> arm: dts: qcom: Add idle states device nodes for 8074
> arm: dts: qcom: Add idle states device nodes for 8084
> arm: dts: qcom: Add idle state device nodes for 8064
>
> .../bindings/arm/msm/qcom,idle-state.txt | 81 +++++
> .../devicetree/bindings/arm/msm/qcom,saw2.txt | 31 +-
> arch/arm/boot/dts/qcom-apq8064.dtsi | 37 ++-
> arch/arm/boot/dts/qcom-apq8084.dtsi | 46 ++-
> arch/arm/boot/dts/qcom-msm8974.dtsi | 46 ++-
> arch/arm/mach-qcom/Makefile | 1 -
> arch/arm/mach-qcom/platsmp.c | 2 +-
> drivers/cpuidle/Kconfig.arm | 7 +
> drivers/cpuidle/Makefile | 1 +
> drivers/cpuidle/cpuidle-qcom.c | 72 +++++
> drivers/soc/qcom/Kconfig | 8 +
> drivers/soc/qcom/Makefile | 3 +-
> .../arm/mach-qcom => drivers/soc/qcom}/scm-boot.c | 33 +-
> drivers/soc/qcom/spm.c | 332 +++++++++++++++++++++
> include/soc/qcom/pm.h | 31 ++
> .../arm/mach-qcom => include/soc/qcom}/scm-boot.h | 3 +-
> 16 files changed, 712 insertions(+), 22 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
> create mode 100644 drivers/cpuidle/cpuidle-qcom.c
> rename {arch/arm/mach-qcom => drivers/soc/qcom}/scm-boot.c (63%)
> create mode 100644 drivers/soc/qcom/spm.c
> create mode 100644 include/soc/qcom/pm.h
> rename {arch/arm/mach-qcom => include/soc/qcom}/scm-boot.h (91%)
>
>--
>2.1.0
>
^ permalink raw reply [flat|nested] 28+ messages in thread