[PATCH v3 0/8] X-Powers Power Supply Improvements

[PATCH v3 0/8] X-Powers Power Supply Improvements

[Samuel Holland]

This series adds some improvements to the axp20x* power supply drivers
to better support suspend/resume and use on mobile devices.

The first two patches fix bugs I found while testing the ONLINE control
added in later patches.

Patches 3 and 7 allow userspace to take the power supplies offline.
Patches 4 and 8 allow userspace to control the wakeup behavior.

Patch 9 avoids polling USB VBUS presence when possible. While working on
the RSB driver, I was seeing ~50 transfers per second, while idle and
tracked it down to this VBUS polling (20 reads/second). The polling
often caused the CPU to clock up and back down, which triggered the
remaining transfers (changes to the CPU voltage).

Unfortunately, I don't see a way to avoid the polling when running on
battery (where it matters most), other than to move the polling back to
the USB PHY driver.

Changes since v2:
 - Patch 1 was merged
 - Only check ACIN_PATH_SEL when necessary (1)
 - Update commit message (5)
 - Avoided reordering lines until/unless necessary (5, 7)
 - Update comment and add ID check in axp20x_usb_power_set_property
   (it seemed more correct than adding another comment) (6)
 - Add Reviewed-by where there were no comments (2-4, 7-8)

Changes since v1:
 - Add patches 1-2
 - Shift value properly in calls to regmap_update_bits (3, 7)
 - Use #ifdef instead of #if to avoid -Wundef warnings (4, 8)
 - Poll once after an IRQ, instead of setting power->online in the IRQ (9)
 - Poll once on resume, in case the state changed during suspend (9)

Samuel Holland (8):
  power: supply: axp20x_ac_power: Fix reporting online status
  power: supply: axp20x_ac_power: Allow offlining
  power: supply: axp20x_ac_power: Add wakeup control
  power: supply: axp20x_usb_power: Remove unused device_node
  power: supply: axp20x_usb_power: Use a match structure
  power: supply: axp20x_usb_power: Allow offlining
  power: supply: axp20x_usb_power: Add wakeup control
  power: supply: axp20x_usb_power: Only poll while offline

 drivers/power/supply/axp20x_ac_power.c  | 131 +++++++++++---
 drivers/power/supply/axp20x_usb_power.c | 219 ++++++++++++++++++------
 2 files changed, 276 insertions(+), 74 deletions(-)

-- 
2.23.0

[PATCH v3 1/8] power: supply: axp20x_ac_power: Fix reporting online status

[Samuel Holland]

AXP803/AXP813 have a flag that enables/disables the AC power supply
input. This flag does not affect the status bits in PWR_INPUT_STATUS.
Its effect can be verified by checking the battery charge/discharge
state (bit 2 of PWR_INPUT_STATUS), or by examining the current draw on
the AC input.

Take this flag into account when getting the ONLINE property of the AC
input, on PMICs where this flag is present.

Fixes: 7693b5643fd2 ("power: supply: add AC power supply driver for AXP813")
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_ac_power.c | 31 +++++++++++++++++++++-----
 1 file changed, 25 insertions(+), 6 deletions(-)

diff --git a/drivers/power/supply/axp20x_ac_power.c b/drivers/power/supply/axp20x_ac_power.c
index 0d34a932b6d5..f74b0556bb6b 100644
--- a/drivers/power/supply/axp20x_ac_power.c
+++ b/drivers/power/supply/axp20x_ac_power.c
@@ -23,6 +23,8 @@
 #define AXP20X_PWR_STATUS_ACIN_PRESENT	BIT(7)
 #define AXP20X_PWR_STATUS_ACIN_AVAIL	BIT(6)
 
+#define AXP813_ACIN_PATH_SEL		BIT(7)
+
 #define AXP813_VHOLD_MASK		GENMASK(5, 3)
 #define AXP813_VHOLD_UV_TO_BIT(x)	((((x) / 100000) - 40) << 3)
 #define AXP813_VHOLD_REG_TO_UV(x)	\
@@ -40,6 +42,7 @@ struct axp20x_ac_power {
 	struct power_supply *supply;
 	struct iio_channel *acin_v;
 	struct iio_channel *acin_i;
+	bool has_acin_path_sel;
 };
 
 static irqreturn_t axp20x_ac_power_irq(int irq, void *devid)
@@ -86,6 +89,17 @@ static int axp20x_ac_power_get_property(struct power_supply *psy,
 			return ret;
 
 		val->intval = !!(reg & AXP20X_PWR_STATUS_ACIN_AVAIL);
+
+		/* ACIN_PATH_SEL disables ACIN even if ACIN_AVAIL is set. */
+		if (val->intval && power->has_acin_path_sel) {
+			ret = regmap_read(power->regmap, AXP813_ACIN_PATH_CTRL,
+					  &reg);
+			if (ret)
+				return ret;
+
+			val->intval = !!(reg & AXP813_ACIN_PATH_SEL);
+		}
+
 		return 0;
 
 	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
@@ -224,21 +238,25 @@ static const struct power_supply_desc axp813_ac_power_desc = {
 struct axp_data {
 	const struct power_supply_desc	*power_desc;
 	bool				acin_adc;
+	bool				acin_path_sel;
 };
 
 static const struct axp_data axp20x_data = {
-	.power_desc = &axp20x_ac_power_desc,
-	.acin_adc = true,
+	.power_desc	= &axp20x_ac_power_desc,
+	.acin_adc	= true,
+	.acin_path_sel	= false,
 };
 
 static const struct axp_data axp22x_data = {
-	.power_desc = &axp22x_ac_power_desc,
-	.acin_adc = false,
+	.power_desc	= &axp22x_ac_power_desc,
+	.acin_adc	= false,
+	.acin_path_sel	= false,
 };
 
 static const struct axp_data axp813_data = {
-	.power_desc = &axp813_ac_power_desc,
-	.acin_adc = false,
+	.power_desc	= &axp813_ac_power_desc,
+	.acin_adc	= false,
+	.acin_path_sel	= true,
 };
 
 static int axp20x_ac_power_probe(struct platform_device *pdev)
@@ -282,6 +300,7 @@ static int axp20x_ac_power_probe(struct platform_device *pdev)
 	}
 
 	power->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	power->has_acin_path_sel = axp_data->acin_path_sel;
 
 	platform_set_drvdata(pdev, power);
 
-- 
2.23.0

Re: [PATCH v3 1/8] power: supply: axp20x_ac_power: Fix reporting online status

[Chen-Yu Tsai]

On Mon, Jan 13, 2020 at 11:53 AM Samuel Holland <samuel@sholland.org> wrote:
>
> AXP803/AXP813 have a flag that enables/disables the AC power supply
> input. This flag does not affect the status bits in PWR_INPUT_STATUS.
> Its effect can be verified by checking the battery charge/discharge
> state (bit 2 of PWR_INPUT_STATUS), or by examining the current draw on
> the AC input.
>
> Take this flag into account when getting the ONLINE property of the AC
> input, on PMICs where this flag is present.
>
> Fixes: 7693b5643fd2 ("power: supply: add AC power supply driver for AXP813")
> Cc: stable@vger.kernel.org
> Signed-off-by: Samuel Holland <samuel@sholland.org>

Reviewed-by: Chen-Yu Tsai <wens@csie.org>

[PATCH v3 2/8] power: supply: axp20x_ac_power: Allow offlining

[Samuel Holland]

AXP803/AXP813 have a flag that enables/disables the AC power supply
input. Allow control of this flag via the ONLINE property on those
variants.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_ac_power.c | 9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

diff --git a/drivers/power/supply/axp20x_ac_power.c b/drivers/power/supply/axp20x_ac_power.c
index f74b0556bb6b..3ba38f2f281c 100644
--- a/drivers/power/supply/axp20x_ac_power.c
+++ b/drivers/power/supply/axp20x_ac_power.c
@@ -24,6 +24,7 @@
 #define AXP20X_PWR_STATUS_ACIN_AVAIL	BIT(6)
 
 #define AXP813_ACIN_PATH_SEL		BIT(7)
+#define AXP813_ACIN_PATH_SEL_TO_BIT(x)	(!!(x) << 7)
 
 #define AXP813_VHOLD_MASK		GENMASK(5, 3)
 #define AXP813_VHOLD_UV_TO_BIT(x)	((((x) / 100000) - 40) << 3)
@@ -157,6 +158,11 @@ static int axp813_ac_power_set_property(struct power_supply *psy,
 	struct axp20x_ac_power *power = power_supply_get_drvdata(psy);
 
 	switch (psp) {
+	case POWER_SUPPLY_PROP_ONLINE:
+		return regmap_update_bits(power->regmap, AXP813_ACIN_PATH_CTRL,
+					  AXP813_ACIN_PATH_SEL,
+					  AXP813_ACIN_PATH_SEL_TO_BIT(val->intval));
+
 	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		if (val->intval < 4000000 || val->intval > 4700000)
 			return -EINVAL;
@@ -183,7 +189,8 @@ static int axp813_ac_power_set_property(struct power_supply *psy,
 static int axp813_ac_power_prop_writeable(struct power_supply *psy,
 					  enum power_supply_property psp)
 {
-	return psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
+	return psp == POWER_SUPPLY_PROP_ONLINE ||
+	       psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
 	       psp == POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT;
 }
 
-- 
2.23.0

[PATCH v3 3/8] power: supply: axp20x_ac_power: Add wakeup control

[Samuel Holland]

The AC power supply input can be used as a wakeup source. Hook up the
ACIN_PLUGIN IRQ to trigger wakeup based on userspace configuration.

To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.

Because we now depend on the specific order of the IRQs (we assume
ACIN_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.

To avoid spuriously waking up the system when the AC power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.

The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_ac_power.c | 91 +++++++++++++++++++++-----
 1 file changed, 74 insertions(+), 17 deletions(-)

diff --git a/drivers/power/supply/axp20x_ac_power.c b/drivers/power/supply/axp20x_ac_power.c
index 3ba38f2f281c..ac360016b08a 100644
--- a/drivers/power/supply/axp20x_ac_power.c
+++ b/drivers/power/supply/axp20x_ac_power.c
@@ -15,6 +15,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/pm.h>
 #include <linux/power_supply.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
@@ -44,6 +45,8 @@ struct axp20x_ac_power {
 	struct iio_channel *acin_v;
 	struct iio_channel *acin_i;
 	bool has_acin_path_sel;
+	unsigned int num_irqs;
+	unsigned int irqs[];
 };
 
 static irqreturn_t axp20x_ac_power_irq(int irq, void *devid)
@@ -242,38 +245,86 @@ static const struct power_supply_desc axp813_ac_power_desc = {
 	.set_property = axp813_ac_power_set_property,
 };
 
+static const char * const axp20x_irq_names[] = {
+	"ACIN_PLUGIN",
+	"ACIN_REMOVAL",
+};
+
 struct axp_data {
 	const struct power_supply_desc	*power_desc;
+	const char * const		*irq_names;
+	unsigned int			num_irq_names;
 	bool				acin_adc;
 	bool				acin_path_sel;
 };
 
 static const struct axp_data axp20x_data = {
 	.power_desc	= &axp20x_ac_power_desc,
+	.irq_names	= axp20x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp20x_irq_names),
 	.acin_adc	= true,
 	.acin_path_sel	= false,
 };
 
 static const struct axp_data axp22x_data = {
 	.power_desc	= &axp22x_ac_power_desc,
+	.irq_names	= axp20x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp20x_irq_names),
 	.acin_adc	= false,
 	.acin_path_sel	= false,
 };
 
 static const struct axp_data axp813_data = {
 	.power_desc	= &axp813_ac_power_desc,
+	.irq_names	= axp20x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp20x_irq_names),
 	.acin_adc	= false,
 	.acin_path_sel	= true,
 };
 
+#ifdef CONFIG_PM_SLEEP
+static int axp20x_ac_power_suspend(struct device *dev)
+{
+	struct axp20x_ac_power *power = dev_get_drvdata(dev);
+	int i = 0;
+
+	/*
+	 * Allow wake via ACIN_PLUGIN only.
+	 *
+	 * As nested threaded IRQs are not automatically disabled during
+	 * suspend, we must explicitly disable the remainder of the IRQs.
+	 */
+	if (device_may_wakeup(&power->supply->dev))
+		enable_irq_wake(power->irqs[i++]);
+	while (i < power->num_irqs)
+		disable_irq(power->irqs[i++]);
+
+	return 0;
+}
+
+static int axp20x_ac_power_resume(struct device *dev)
+{
+	struct axp20x_ac_power *power = dev_get_drvdata(dev);
+	int i = 0;
+
+	if (device_may_wakeup(&power->supply->dev))
+		disable_irq_wake(power->irqs[i++]);
+	while (i < power->num_irqs)
+		enable_irq(power->irqs[i++]);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(axp20x_ac_power_pm_ops, axp20x_ac_power_suspend,
+						 axp20x_ac_power_resume);
+
 static int axp20x_ac_power_probe(struct platform_device *pdev)
 {
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
 	struct power_supply_config psy_cfg = {};
 	struct axp20x_ac_power *power;
 	const struct axp_data *axp_data;
-	static const char * const irq_names[] = { "ACIN_PLUGIN", "ACIN_REMOVAL",
-		NULL };
 	int i, irq, ret;
 
 	if (!of_device_is_available(pdev->dev.of_node))
@@ -284,12 +335,14 @@ static int axp20x_ac_power_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	axp_data = of_device_get_match_data(&pdev->dev);
+
+	power = devm_kzalloc(&pdev->dev,
+			     struct_size(power, irqs, axp_data->num_irq_names),
+			     GFP_KERNEL);
 	if (!power)
 		return -ENOMEM;
 
-	axp_data = of_device_get_match_data(&pdev->dev);
-
 	if (axp_data->acin_adc) {
 		power->acin_v = devm_iio_channel_get(&pdev->dev, "acin_v");
 		if (IS_ERR(power->acin_v)) {
@@ -308,6 +361,7 @@ static int axp20x_ac_power_probe(struct platform_device *pdev)
 
 	power->regmap = dev_get_regmap(pdev->dev.parent, NULL);
 	power->has_acin_path_sel = axp_data->acin_path_sel;
+	power->num_irqs = axp_data->num_irq_names;
 
 	platform_set_drvdata(pdev, power);
 
@@ -321,20 +375,22 @@ static int axp20x_ac_power_probe(struct platform_device *pdev)
 		return PTR_ERR(power->supply);
 
 	/* Request irqs after registering, as irqs may trigger immediately */
-	for (i = 0; irq_names[i]; i++) {
-		irq = platform_get_irq_byname(pdev, irq_names[i]);
+	for (i = 0; i < axp_data->num_irq_names; i++) {
+		irq = platform_get_irq_byname(pdev, axp_data->irq_names[i]);
 		if (irq < 0) {
-			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
-				 irq_names[i], irq);
-			continue;
+			dev_err(&pdev->dev, "No IRQ for %s: %d\n",
+				axp_data->irq_names[i], irq);
+			return irq;
 		}
-		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
-		ret = devm_request_any_context_irq(&pdev->dev, irq,
+		power->irqs[i] = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		ret = devm_request_any_context_irq(&pdev->dev, power->irqs[i],
 						   axp20x_ac_power_irq, 0,
 						   DRVNAME, power);
-		if (ret < 0)
-			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
-				 irq_names[i], ret);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				axp_data->irq_names[i], ret);
+			return ret;
+		}
 	}
 
 	return 0;
@@ -357,8 +413,9 @@ MODULE_DEVICE_TABLE(of, axp20x_ac_power_match);
 static struct platform_driver axp20x_ac_power_driver = {
 	.probe = axp20x_ac_power_probe,
 	.driver = {
-		.name = DRVNAME,
-		.of_match_table = axp20x_ac_power_match,
+		.name		= DRVNAME,
+		.of_match_table	= axp20x_ac_power_match,
+		.pm		= &axp20x_ac_power_pm_ops,
 	},
 };
 
-- 
2.23.0

[PATCH v3 4/8] power: supply: axp20x_usb_power: Remove unused device_node

[Samuel Holland]

This member of struct axp20x_usb_power is not used anywhere.
Remove it.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_usb_power.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index dc4c316eff81..2573de2a0adc 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -55,7 +55,6 @@
 #define DEBOUNCE_TIME			msecs_to_jiffies(50)
 
 struct axp20x_usb_power {
-	struct device_node *np;
 	struct regmap *regmap;
 	struct power_supply *supply;
 	enum axp20x_variants axp20x_id;
@@ -463,7 +462,6 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 	power->axp20x_id = (enum axp20x_variants)of_device_get_match_data(
 								&pdev->dev);
 
-	power->np = pdev->dev.of_node;
 	power->regmap = axp20x->regmap;
 
 	if (power->axp20x_id == AXP202_ID) {
-- 
2.23.0

[PATCH v3 5/8] power: supply: axp20x_usb_power: Use a match structure

[Samuel Holland]

Instead of ad-hoc variant ID checks throughout the code, let's start
moving the variant-specific details to a match structure. This allows
for future flexibility, and it better matches the other axp20x power
supply drivers.

This commit removes most variant checks from axp20x_usb_power_probe().
Other parts of the driver still do ID matching; they are left unchanged
for now.

Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_usb_power.c | 86 ++++++++++++++++---------
 1 file changed, 57 insertions(+), 29 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index 2573de2a0adc..cd89ee12dd18 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -403,6 +403,50 @@ static const struct power_supply_desc axp22x_usb_power_desc = {
 	.set_property = axp20x_usb_power_set_property,
 };
 
+static const char * const axp20x_irq_names[] = {
+	"VBUS_PLUGIN",
+	"VBUS_REMOVAL",
+	"VBUS_VALID",
+	"VBUS_NOT_VALID",
+	NULL
+};
+
+static const char * const axp22x_irq_names[] = {
+	"VBUS_PLUGIN",
+	"VBUS_REMOVAL",
+	NULL
+};
+
+struct axp_data {
+	const struct power_supply_desc	*power_desc;
+	const char * const		*irq_names;
+	enum axp20x_variants		axp20x_id;
+};
+
+static const struct axp_data axp202_data = {
+	.power_desc	= &axp20x_usb_power_desc,
+	.irq_names	= axp20x_irq_names,
+	.axp20x_id	= AXP202_ID,
+};
+
+static const struct axp_data axp221_data = {
+	.power_desc	= &axp22x_usb_power_desc,
+	.irq_names	= axp22x_irq_names,
+	.axp20x_id	= AXP221_ID,
+};
+
+static const struct axp_data axp223_data = {
+	.power_desc	= &axp22x_usb_power_desc,
+	.irq_names	= axp22x_irq_names,
+	.axp20x_id	= AXP223_ID,
+};
+
+static const struct axp_data axp813_data = {
+	.power_desc	= &axp22x_usb_power_desc,
+	.irq_names	= axp22x_irq_names,
+	.axp20x_id	= AXP813_ID,
+};
+
 static int configure_iio_channels(struct platform_device *pdev,
 				  struct axp20x_usb_power *power)
 {
@@ -438,12 +482,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 	struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
 	struct power_supply_config psy_cfg = {};
 	struct axp20x_usb_power *power;
-	static const char * const axp20x_irq_names[] = { "VBUS_PLUGIN",
-		"VBUS_REMOVAL", "VBUS_VALID", "VBUS_NOT_VALID", NULL };
-	static const char * const axp22x_irq_names[] = {
-		"VBUS_PLUGIN", "VBUS_REMOVAL", NULL };
-	const char * const *irq_names;
-	const struct power_supply_desc *usb_power_desc;
+	const struct axp_data *axp_data;
 	int i, irq, ret;
 
 	if (!of_device_is_available(pdev->dev.of_node))
@@ -459,9 +498,9 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	platform_set_drvdata(pdev, power);
-	power->axp20x_id = (enum axp20x_variants)of_device_get_match_data(
-								&pdev->dev);
 
+	axp_data = of_device_get_match_data(&pdev->dev);
+	power->axp20x_id = axp_data->axp20x_id;
 	power->regmap = axp20x->regmap;
 
 	if (power->axp20x_id == AXP202_ID) {
@@ -479,34 +518,23 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 
 		if (ret)
 			return ret;
-
-		usb_power_desc = &axp20x_usb_power_desc;
-		irq_names = axp20x_irq_names;
-	} else if (power->axp20x_id == AXP221_ID ||
-		   power->axp20x_id == AXP223_ID ||
-		   power->axp20x_id == AXP813_ID) {
-		usb_power_desc = &axp22x_usb_power_desc;
-		irq_names = axp22x_irq_names;
-	} else {
-		dev_err(&pdev->dev, "Unsupported AXP variant: %ld\n",
-			axp20x->variant);
-		return -EINVAL;
 	}
 
 	psy_cfg.of_node = pdev->dev.of_node;
 	psy_cfg.drv_data = power;
 
-	power->supply = devm_power_supply_register(&pdev->dev, usb_power_desc,
+	power->supply = devm_power_supply_register(&pdev->dev,
+						   axp_data->power_desc,
 						   &psy_cfg);
 	if (IS_ERR(power->supply))
 		return PTR_ERR(power->supply);
 
 	/* Request irqs after registering, as irqs may trigger immediately */
-	for (i = 0; irq_names[i]; i++) {
-		irq = platform_get_irq_byname(pdev, irq_names[i]);
+	for (i = 0; axp_data->irq_names[i]; i++) {
+		irq = platform_get_irq_byname(pdev, axp_data->irq_names[i]);
 		if (irq < 0) {
 			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
-				 irq_names[i], irq);
+				 axp_data->irq_names[i], irq);
 			continue;
 		}
 		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
@@ -514,7 +542,7 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 				axp20x_usb_power_irq, 0, DRVNAME, power);
 		if (ret < 0)
 			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
-				 irq_names[i], ret);
+				 axp_data->irq_names[i], ret);
 	}
 
 	INIT_DELAYED_WORK(&power->vbus_detect, axp20x_usb_power_poll_vbus);
@@ -536,16 +564,16 @@ static int axp20x_usb_power_remove(struct platform_device *pdev)
 static const struct of_device_id axp20x_usb_power_match[] = {
 	{
 		.compatible = "x-powers,axp202-usb-power-supply",
-		.data = (void *)AXP202_ID,
+		.data = &axp202_data,
 	}, {
 		.compatible = "x-powers,axp221-usb-power-supply",
-		.data = (void *)AXP221_ID,
+		.data = &axp221_data,
 	}, {
 		.compatible = "x-powers,axp223-usb-power-supply",
-		.data = (void *)AXP223_ID,
+		.data = &axp223_data,
 	}, {
 		.compatible = "x-powers,axp813-usb-power-supply",
-		.data = (void *)AXP813_ID,
+		.data = &axp813_data,
 	}, { /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, axp20x_usb_power_match);
-- 
2.23.0

Re: [PATCH v3 5/8] power: supply: axp20x_usb_power: Use a match structure

[Chen-Yu Tsai]

On Mon, Jan 13, 2020 at 11:53 AM Samuel Holland <samuel@sholland.org> wrote:
>
> Instead of ad-hoc variant ID checks throughout the code, let's start
> moving the variant-specific details to a match structure. This allows
> for future flexibility, and it better matches the other axp20x power
> supply drivers.
>
> This commit removes most variant checks from axp20x_usb_power_probe().
> Other parts of the driver still do ID matching; they are left unchanged
> for now.
>
> Signed-off-by: Samuel Holland <samuel@sholland.org>

Reviewed-by: Chen-Yu Tsai <wens@csie.org>

[PATCH v3 6/8] power: supply: axp20x_usb_power: Allow offlining

[Samuel Holland]

AXP803/AXP813 have a flag that enables/disables the USB power supply
input. Allow control of this flag via the ONLINE property on those
variants.

It may be necessary to offline the USB power supply input when using
the USB port in OTG mode, or to allow userspace to disable charging.

When the USB VBUS input is disabled via the PATH_SEL bit, the VBUS_USED
bit in PWR_INPUT_STATUS is cleared, so there is no change needed when
getting the property.

Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_usb_power.c | 30 +++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index cd89ee12dd18..3b3cc1e33f19 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -29,6 +29,9 @@
 
 #define AXP20X_USB_STATUS_VBUS_VALID	BIT(2)
 
+#define AXP20X_VBUS_PATH_SEL		BIT(7)
+#define AXP20X_VBUS_PATH_SEL_OFFSET	7
+
 #define AXP20X_VBUS_VHOLD_uV(b)		(4000000 + (((b) >> 3) & 7) * 100000)
 #define AXP20X_VBUS_VHOLD_MASK		GENMASK(5, 3)
 #define AXP20X_VBUS_VHOLD_OFFSET	3
@@ -261,6 +264,16 @@ static int axp20x_usb_power_get_property(struct power_supply *psy,
 	return 0;
 }
 
+static int axp813_usb_power_set_online(struct axp20x_usb_power *power,
+				       int intval)
+{
+	int val = !intval << AXP20X_VBUS_PATH_SEL_OFFSET;
+
+	return regmap_update_bits(power->regmap,
+				  AXP20X_VBUS_IPSOUT_MGMT,
+				  AXP20X_VBUS_PATH_SEL, val);
+}
+
 static int axp20x_usb_power_set_voltage_min(struct axp20x_usb_power *power,
 					    int intval)
 {
@@ -342,6 +355,11 @@ static int axp20x_usb_power_set_property(struct power_supply *psy,
 	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
 
 	switch (psp) {
+	case POWER_SUPPLY_PROP_ONLINE:
+		if (power->axp20x_id != AXP813_ID)
+			return -EINVAL;
+		return axp813_usb_power_set_online(power, val->intval);
+
 	case POWER_SUPPLY_PROP_VOLTAGE_MIN:
 		return axp20x_usb_power_set_voltage_min(power, val->intval);
 
@@ -361,6 +379,18 @@ static int axp20x_usb_power_set_property(struct power_supply *psy,
 static int axp20x_usb_power_prop_writeable(struct power_supply *psy,
 					   enum power_supply_property psp)
 {
+	struct axp20x_usb_power *power = power_supply_get_drvdata(psy);
+
+	/*
+	 * The VBUS path select flag works differently on on AXP288 and newer:
+	 *  - On AXP20x and AXP22x, the flag enables VBUS (ignoring N_VBUSEN).
+	 *  - On AXP288 and AXP8xx, the flag disables VBUS (ignoring N_VBUSEN).
+	 * We only expose the control on variants where it can be used to force
+	 * the VBUS input offline.
+	 */
+	if (psp == POWER_SUPPLY_PROP_ONLINE)
+		return power->axp20x_id == AXP813_ID;
+
 	return psp == POWER_SUPPLY_PROP_VOLTAGE_MIN ||
 	       psp == POWER_SUPPLY_PROP_CURRENT_MAX;
 }
-- 
2.23.0

Re: [linux-sunxi] [PATCH v3 6/8] power: supply: axp20x_usb_power: Allow offlining

[Chen-Yu Tsai]

On Mon, Jan 13, 2020 at 11:53 AM Samuel Holland <samuel@sholland.org> wrote:
>
> AXP803/AXP813 have a flag that enables/disables the USB power supply
> input. Allow control of this flag via the ONLINE property on those
> variants.
>
> It may be necessary to offline the USB power supply input when using
> the USB port in OTG mode, or to allow userspace to disable charging.
>
> When the USB VBUS input is disabled via the PATH_SEL bit, the VBUS_USED
> bit in PWR_INPUT_STATUS is cleared, so there is no change needed when
> getting the property.
>
> Signed-off-by: Samuel Holland <samuel@sholland.org>

Reviewed-by: Chen-Yu Tsai <wens@csie.org>

[PATCH v3 7/8] power: supply: axp20x_usb_power: Add wakeup control

[Samuel Holland]

The USB power supply input can be used as a wakeup source. Hook up the
VBUS_PLUGIN IRQ to trigger wakeup based on userspace configuration.

To do this, we must remember the list of IRQs for the life of the
device. To know how much space to allocate for the flexible array
member, we switch from using a NULL sentinel to using an array length.

Because we now depend on the specific order of the IRQs (we assume
VBUS_PLUGIN is first and always present), failing to acquire an IRQ
during probe must be a fatal error.

To avoid spuriously waking up the system when the USB power supply is
not configured as a wakeup source, we must explicitly disable all non-
wake IRQs during system suspend. This is because the SoC's NMI input is
shared among all IRQs on the AXP PMIC. Due to the use of regmap-irq, the
individual IRQs within the PMIC are nested threaded interrupts, and are
therefore not automatically disabled during system suspend.

The upshot is that if any other device within the MFD (such as the power
key) is an enabled wakeup source, all enabled IRQs within the PMIC will
cause wakeup. We still need to call enable_irq_wake() when we *do* want
wakeup, in case those other wakeup sources on the PMIC are all disabled.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_usb_power.c | 83 ++++++++++++++++++++-----
 1 file changed, 67 insertions(+), 16 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index 3b3cc1e33f19..4292b86d0429 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -16,6 +16,7 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/platform_device.h>
+#include <linux/pm.h>
 #include <linux/power_supply.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
@@ -65,6 +66,8 @@ struct axp20x_usb_power {
 	struct iio_channel *vbus_i;
 	struct delayed_work vbus_detect;
 	unsigned int old_status;
+	unsigned int num_irqs;
+	unsigned int irqs[];
 };
 
 static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
@@ -438,45 +441,85 @@ static const char * const axp20x_irq_names[] = {
 	"VBUS_REMOVAL",
 	"VBUS_VALID",
 	"VBUS_NOT_VALID",
-	NULL
 };
 
 static const char * const axp22x_irq_names[] = {
 	"VBUS_PLUGIN",
 	"VBUS_REMOVAL",
-	NULL
 };
 
 struct axp_data {
 	const struct power_supply_desc	*power_desc;
 	const char * const		*irq_names;
+	unsigned int			num_irq_names;
 	enum axp20x_variants		axp20x_id;
 };
 
 static const struct axp_data axp202_data = {
 	.power_desc	= &axp20x_usb_power_desc,
 	.irq_names	= axp20x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp20x_irq_names),
 	.axp20x_id	= AXP202_ID,
 };
 
 static const struct axp_data axp221_data = {
 	.power_desc	= &axp22x_usb_power_desc,
 	.irq_names	= axp22x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp22x_irq_names),
 	.axp20x_id	= AXP221_ID,
 };
 
 static const struct axp_data axp223_data = {
 	.power_desc	= &axp22x_usb_power_desc,
 	.irq_names	= axp22x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp22x_irq_names),
 	.axp20x_id	= AXP223_ID,
 };
 
 static const struct axp_data axp813_data = {
 	.power_desc	= &axp22x_usb_power_desc,
 	.irq_names	= axp22x_irq_names,
+	.num_irq_names	= ARRAY_SIZE(axp22x_irq_names),
 	.axp20x_id	= AXP813_ID,
 };
 
+#ifdef CONFIG_PM_SLEEP
+static int axp20x_usb_power_suspend(struct device *dev)
+{
+	struct axp20x_usb_power *power = dev_get_drvdata(dev);
+	int i = 0;
+
+	/*
+	 * Allow wake via VBUS_PLUGIN only.
+	 *
+	 * As nested threaded IRQs are not automatically disabled during
+	 * suspend, we must explicitly disable the remainder of the IRQs.
+	 */
+	if (device_may_wakeup(&power->supply->dev))
+		enable_irq_wake(power->irqs[i++]);
+	while (i < power->num_irqs)
+		disable_irq(power->irqs[i++]);
+
+	return 0;
+}
+
+static int axp20x_usb_power_resume(struct device *dev)
+{
+	struct axp20x_usb_power *power = dev_get_drvdata(dev);
+	int i = 0;
+
+	if (device_may_wakeup(&power->supply->dev))
+		disable_irq_wake(power->irqs[i++]);
+	while (i < power->num_irqs)
+		enable_irq(power->irqs[i++]);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(axp20x_usb_power_pm_ops, axp20x_usb_power_suspend,
+						  axp20x_usb_power_resume);
+
 static int configure_iio_channels(struct platform_device *pdev,
 				  struct axp20x_usb_power *power)
 {
@@ -523,15 +566,19 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	power = devm_kzalloc(&pdev->dev, sizeof(*power), GFP_KERNEL);
+	axp_data = of_device_get_match_data(&pdev->dev);
+
+	power = devm_kzalloc(&pdev->dev,
+			     struct_size(power, irqs, axp_data->num_irq_names),
+			     GFP_KERNEL);
 	if (!power)
 		return -ENOMEM;
 
 	platform_set_drvdata(pdev, power);
 
-	axp_data = of_device_get_match_data(&pdev->dev);
 	power->axp20x_id = axp_data->axp20x_id;
 	power->regmap = axp20x->regmap;
+	power->num_irqs = axp_data->num_irq_names;
 
 	if (power->axp20x_id == AXP202_ID) {
 		/* Enable vbus valid checking */
@@ -560,19 +607,22 @@ static int axp20x_usb_power_probe(struct platform_device *pdev)
 		return PTR_ERR(power->supply);
 
 	/* Request irqs after registering, as irqs may trigger immediately */
-	for (i = 0; axp_data->irq_names[i]; i++) {
+	for (i = 0; i < axp_data->num_irq_names; i++) {
 		irq = platform_get_irq_byname(pdev, axp_data->irq_names[i]);
 		if (irq < 0) {
-			dev_warn(&pdev->dev, "No IRQ for %s: %d\n",
-				 axp_data->irq_names[i], irq);
-			continue;
+			dev_err(&pdev->dev, "No IRQ for %s: %d\n",
+				axp_data->irq_names[i], irq);
+			return irq;
+		}
+		power->irqs[i] = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
+		ret = devm_request_any_context_irq(&pdev->dev, power->irqs[i],
+						   axp20x_usb_power_irq, 0,
+						   DRVNAME, power);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "Error requesting %s IRQ: %d\n",
+				axp_data->irq_names[i], ret);
+			return ret;
 		}
-		irq = regmap_irq_get_virq(axp20x->regmap_irqc, irq);
-		ret = devm_request_any_context_irq(&pdev->dev, irq,
-				axp20x_usb_power_irq, 0, DRVNAME, power);
-		if (ret < 0)
-			dev_warn(&pdev->dev, "Error requesting %s IRQ: %d\n",
-				 axp_data->irq_names[i], ret);
 	}
 
 	INIT_DELAYED_WORK(&power->vbus_detect, axp20x_usb_power_poll_vbus);
@@ -612,8 +662,9 @@ static struct platform_driver axp20x_usb_power_driver = {
 	.probe = axp20x_usb_power_probe,
 	.remove = axp20x_usb_power_remove,
 	.driver = {
-		.name = DRVNAME,
-		.of_match_table = axp20x_usb_power_match,
+		.name		= DRVNAME,
+		.of_match_table	= axp20x_usb_power_match,
+		.pm		= &axp20x_usb_power_pm_ops,
 	},
 };
 
-- 
2.23.0

[PATCH v3 8/8] power: supply: axp20x_usb_power: Only poll while offline

[Samuel Holland]

Investigation on the AXP803 shows that VBUS_PLUGIN/VBUS_REMOVAL IRQs are
triggered on the rising/falling edge of AXP20X_PWR_STATUS_VBUS_USED. The
reason IRQs do not arrive while N_VBUSEN/DRIVEVBUS is high is because
AXP20X_PWR_STATUS_VBUS_USED also never goes high.

This also means that if VBUS is online, a VBUS_REMOVAL IRQ is received
immediately on setting N_VBUSEN/DRIVEVBUS high (and VBUS_PLUGIN shortly
after it is set back low). This was also verified to be the case when
manually offlining VBUS through AXP20X_VBUS_PATH_SELECT.

As long as VBUS is online, a present->absent transition necessarily
implies an online->offline transition. Since will cause an IRQ, there is
no need to poll while VBUS is online.

To ensure the driver's view of VBUS online status remains accurate,
unconditionally poll once when receiving an IRQ and when resuming. If
VBUS is still online at that time, polling will cease until the next
VBUS_REMOVAL IRQ.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
 drivers/power/supply/axp20x_usb_power.c | 30 +++++++++++++++++--------
 1 file changed, 21 insertions(+), 9 deletions(-)

diff --git a/drivers/power/supply/axp20x_usb_power.c b/drivers/power/supply/axp20x_usb_power.c
index 4292b86d0429..fbb66e97787d 100644
--- a/drivers/power/supply/axp20x_usb_power.c
+++ b/drivers/power/supply/axp20x_usb_power.c
@@ -66,16 +66,32 @@ struct axp20x_usb_power {
 	struct iio_channel *vbus_i;
 	struct delayed_work vbus_detect;
 	unsigned int old_status;
+	unsigned int online;
 	unsigned int num_irqs;
 	unsigned int irqs[];
 };
 
+static bool axp20x_usb_vbus_needs_polling(struct axp20x_usb_power *power)
+{
+	/*
+	 * Polling is only necessary while VBUS is offline. While online, a
+	 * present->absent transition implies an online->offline transition
+	 * and will triger the VBUS_REMOVAL IRQ.
+	 */
+	if (power->axp20x_id >= AXP221_ID && !power->online)
+		return true;
+
+	return false;
+}
+
 static irqreturn_t axp20x_usb_power_irq(int irq, void *devid)
 {
 	struct axp20x_usb_power *power = devid;
 
 	power_supply_changed(power->supply);
 
+	mod_delayed_work(system_wq, &power->vbus_detect, DEBOUNCE_TIME);
+
 	return IRQ_HANDLED;
 }
 
@@ -95,17 +111,11 @@ static void axp20x_usb_power_poll_vbus(struct work_struct *work)
 		power_supply_changed(power->supply);
 
 	power->old_status = val;
+	power->online = val & AXP20X_PWR_STATUS_VBUS_USED;
 
 out:
-	mod_delayed_work(system_wq, &power->vbus_detect, DEBOUNCE_TIME);
-}
-
-static bool axp20x_usb_vbus_needs_polling(struct axp20x_usb_power *power)
-{
-	if (power->axp20x_id >= AXP221_ID)
-		return true;
-
-	return false;
+	if (axp20x_usb_vbus_needs_polling(power))
+		mod_delayed_work(system_wq, &power->vbus_detect, DEBOUNCE_TIME);
 }
 
 static int axp20x_get_current_max(struct axp20x_usb_power *power, int *val)
@@ -513,6 +523,8 @@ static int axp20x_usb_power_resume(struct device *dev)
 	while (i < power->num_irqs)
 		enable_irq(power->irqs[i++]);
 
+	mod_delayed_work(system_wq, &power->vbus_detect, DEBOUNCE_TIME);
+
 	return 0;
 }
 #endif
-- 
2.23.0

Re: [PATCH v3 0/8] X-Powers Power Supply Improvements

[Sebastian Reichel]

[-- Attachment #1: Type: text/plain, Size: 2524 bytes --]

Hi,

I queued patches 1-4, patch 5 does not apply and seems to be based
on an older tree.

-- Sebastian

On Sun, Jan 12, 2020 at 09:53:02PM -0600, Samuel Holland wrote:
> This series adds some improvements to the axp20x* power supply drivers
> to better support suspend/resume and use on mobile devices.
> 
> The first two patches fix bugs I found while testing the ONLINE control
> added in later patches.
> 
> Patches 3 and 7 allow userspace to take the power supplies offline.
> Patches 4 and 8 allow userspace to control the wakeup behavior.
> 
> Patch 9 avoids polling USB VBUS presence when possible. While working on
> the RSB driver, I was seeing ~50 transfers per second, while idle and
> tracked it down to this VBUS polling (20 reads/second). The polling
> often caused the CPU to clock up and back down, which triggered the
> remaining transfers (changes to the CPU voltage).
> 
> Unfortunately, I don't see a way to avoid the polling when running on
> battery (where it matters most), other than to move the polling back to
> the USB PHY driver.
> 
> Changes since v2:
>  - Patch 1 was merged
>  - Only check ACIN_PATH_SEL when necessary (1)
>  - Update commit message (5)
>  - Avoided reordering lines until/unless necessary (5, 7)
>  - Update comment and add ID check in axp20x_usb_power_set_property
>    (it seemed more correct than adding another comment) (6)
>  - Add Reviewed-by where there were no comments (2-4, 7-8)
> 
> Changes since v1:
>  - Add patches 1-2
>  - Shift value properly in calls to regmap_update_bits (3, 7)
>  - Use #ifdef instead of #if to avoid -Wundef warnings (4, 8)
>  - Poll once after an IRQ, instead of setting power->online in the IRQ (9)
>  - Poll once on resume, in case the state changed during suspend (9)
> 
> Samuel Holland (8):
>   power: supply: axp20x_ac_power: Fix reporting online status
>   power: supply: axp20x_ac_power: Allow offlining
>   power: supply: axp20x_ac_power: Add wakeup control
>   power: supply: axp20x_usb_power: Remove unused device_node
>   power: supply: axp20x_usb_power: Use a match structure
>   power: supply: axp20x_usb_power: Allow offlining
>   power: supply: axp20x_usb_power: Add wakeup control
>   power: supply: axp20x_usb_power: Only poll while offline
> 
>  drivers/power/supply/axp20x_ac_power.c  | 131 +++++++++++---
>  drivers/power/supply/axp20x_usb_power.c | 219 ++++++++++++++++++------
>  2 files changed, 276 insertions(+), 74 deletions(-)
> 
> -- 
> 2.23.0
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]