* [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI @ 2023-03-30 16:46 Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible Dylan Van Assche ` (4 more replies) 0 siblings, 5 replies; 8+ messages in thread From: Dylan Van Assche @ 2023-03-30 16:46 UTC (permalink / raw) To: Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel, Dylan Van Assche * About * The Qualcomm SDM845 SoC has a separate SLPI (Sensor Low Power Island) DSP for sensors connected to the SoC which is responsible for exposing sensors to userspace, power saving, and other features. While sensors are connected to GPIOs of the SoC, they cannot be used because the hypervisor blocks direct access to the sensors, thus the DSP must be used to access any sensor on this SoC. The SLPI DSP uses a GLink edge (dsps) to communicate with the host and has a FastRPC interface to load files from the host filesystem such as sensor configuration files. The FastRPC interface does not use regular FastRPC Compute Banks but instead uses an allocated CMA region through which communication happens. * Changes * This patchseries adds support for this remoteproc in the q6v5_pas driver to allow booting the SLPI on the SDM845 and expose its service 400 over QRTR. * Related patches * Support for the FastRPC side of the SLPI and DTS changes are submitted in separate series. These are the links to v2 of the series: 1. FastRPC changes: https://lore.kernel.org/linux-arm-msm/20230327184204.498032-1-me@dylanvanassche.be/ 2. DTS changes: https://lore.kernel.org/linux-devicetree/20230327184811.499553-1-me@dylanvanassche.be * Changelog * Changes in v2: - Removed double blank lines - Added power-domain if:then: for SDM845 SLPI - After adding SDM845 SLPI, refactor SLPI resource init Changes in v3: - First refactor SLPI resources of SM8150/SM8250/SM8350/SM8450/MSM8996/MSM8998, then add support for SDM845 SLPI. - Add Reviewed-by for patch 'dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible' since it was not changed in v3. Kind regards, Dylan Van Assche Dylan Van Assche (3): dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible remoteproc: qcom: pas: refactor SLPI remoteproc init remoteproc: qcom: pas: add SDM845 SLPI compatible .../bindings/remoteproc/qcom,adsp.yaml | 19 +++++++ drivers/remoteproc/qcom_q6v5_pas.c | 49 ++++--------------- 2 files changed, 28 insertions(+), 40 deletions(-) -- 2.39.2 ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v3 1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche @ 2023-03-30 16:46 ` Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init Dylan Van Assche ` (3 subsequent siblings) 4 siblings, 0 replies; 8+ messages in thread From: Dylan Van Assche @ 2023-03-30 16:46 UTC (permalink / raw) To: Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel, Dylan Van Assche, Krzysztof Kozlowski SLPI DSP remoteproc on DSP is defined by the 'qcom,sdm845-slpi-pas' compatible in the qcom_q6v5_pas driver. Add this compatible to the devicetree bindings. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- .../bindings/remoteproc/qcom,adsp.yaml | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml index 643ee787a81f..eb4a440a661a 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml @@ -26,6 +26,7 @@ properties: - qcom,sdm660-adsp-pas - qcom,sdm845-adsp-pas - qcom,sdm845-cdsp-pas + - qcom,sdm845-slpi-pas reg: maxItems: 1 @@ -63,6 +64,7 @@ allOf: - qcom,msm8998-adsp-pas - qcom,sdm845-adsp-pas - qcom,sdm845-cdsp-pas + - qcom,sdm845-slpi-pas then: properties: clocks: @@ -104,6 +106,7 @@ allOf: - qcom,msm8998-slpi-pas - qcom,sdm845-adsp-pas - qcom,sdm845-cdsp-pas + - qcom,sdm845-slpi-pas then: properties: interrupts: @@ -157,6 +160,22 @@ allOf: required: - px-supply + - if: + properties: + compatible: + enum: + - qcom,sdm845-slpi-pas + then: + properties: + power-domains: + items: + - description: LCX power domain + - description: LMX power domain + power-domain-names: + items: + - const: lcx + - const: lmx + - if: properties: compatible: -- 2.39.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible Dylan Van Assche @ 2023-03-30 16:46 ` Dylan Van Assche 2023-03-30 23:03 ` Konrad Dybcio 2023-03-30 16:46 ` [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible Dylan Van Assche ` (2 subsequent siblings) 4 siblings, 1 reply; 8+ messages in thread From: Dylan Van Assche @ 2023-03-30 16:46 UTC (permalink / raw) To: Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel, Dylan Van Assche SLPI remoteproc initialization is the same for SDM845, SM8150, SM8250, SM8350 but is duplicated for each compatible. Refactor initialization structs for these 4 compatibles as a single struct. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> --- drivers/remoteproc/qcom_q6v5_pas.c | 48 +++++------------------------- 1 file changed, 8 insertions(+), 40 deletions(-) diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c index c99a20542685..b96020c93e58 100644 --- a/drivers/remoteproc/qcom_q6v5_pas.c +++ b/drivers/remoteproc/qcom_q6v5_pas.c @@ -1014,7 +1014,7 @@ static const struct adsp_data sc8180x_mpss_resource = { .ssctl_id = 0x12, }; -static const struct adsp_data slpi_resource_init = { +static const struct adsp_data msm8996_slpi_resource_init = { .crash_reason_smem = 424, .firmware_name = "slpi.mdt", .pas_id = 12, @@ -1028,7 +1028,7 @@ static const struct adsp_data slpi_resource_init = { .ssctl_id = 0x16, }; -static const struct adsp_data sm8150_slpi_resource = { +static const struct adsp_data sdm845_slpi_resource_init = { .crash_reason_smem = 424, .firmware_name = "slpi.mdt", .pas_id = 12, @@ -1044,38 +1044,6 @@ static const struct adsp_data sm8150_slpi_resource = { .ssctl_id = 0x16, }; -static const struct adsp_data sm8250_slpi_resource = { - .crash_reason_smem = 424, - .firmware_name = "slpi.mdt", - .pas_id = 12, - .auto_boot = true, - .proxy_pd_names = (char*[]){ - "lcx", - "lmx", - NULL - }, - .load_state = "slpi", - .ssr_name = "dsps", - .sysmon_name = "slpi", - .ssctl_id = 0x16, -}; - -static const struct adsp_data sm8350_slpi_resource = { - .crash_reason_smem = 424, - .firmware_name = "slpi.mdt", - .pas_id = 12, - .auto_boot = true, - .proxy_pd_names = (char*[]){ - "lcx", - "lmx", - NULL - }, - .load_state = "slpi", - .ssr_name = "dsps", - .sysmon_name = "slpi", - .ssctl_id = 0x16, -}; - static const struct adsp_data wcss_resource_init = { .crash_reason_smem = 421, .firmware_name = "wcnss.mdt", @@ -1184,9 +1152,9 @@ static const struct of_device_id adsp_of_match[] = { { .compatible = "qcom,msm8953-adsp-pil", .data = &msm8996_adsp_resource}, { .compatible = "qcom,msm8974-adsp-pil", .data = &adsp_resource_init}, { .compatible = "qcom,msm8996-adsp-pil", .data = &msm8996_adsp_resource}, - { .compatible = "qcom,msm8996-slpi-pil", .data = &slpi_resource_init}, + { .compatible = "qcom,msm8996-slpi-pil", .data = &msm8996_slpi_resource_init}, { .compatible = "qcom,msm8998-adsp-pas", .data = &msm8996_adsp_resource}, - { .compatible = "qcom,msm8998-slpi-pas", .data = &slpi_resource_init}, + { .compatible = "qcom,msm8998-slpi-pas", .data = &msm8996_slpi_resource_init}, { .compatible = "qcom,qcs404-adsp-pas", .data = &adsp_resource_init }, { .compatible = "qcom,qcs404-cdsp-pas", .data = &cdsp_resource_init }, { .compatible = "qcom,qcs404-wcss-pas", .data = &wcss_resource_init }, @@ -1211,17 +1179,17 @@ static const struct of_device_id adsp_of_match[] = { { .compatible = "qcom,sm8150-adsp-pas", .data = &sm8150_adsp_resource}, { .compatible = "qcom,sm8150-cdsp-pas", .data = &sm8150_cdsp_resource}, { .compatible = "qcom,sm8150-mpss-pas", .data = &mpss_resource_init}, - { .compatible = "qcom,sm8150-slpi-pas", .data = &sm8150_slpi_resource}, + { .compatible = "qcom,sm8150-slpi-pas", .data = &sdm845_slpi_resource_init}, { .compatible = "qcom,sm8250-adsp-pas", .data = &sm8250_adsp_resource}, { .compatible = "qcom,sm8250-cdsp-pas", .data = &sm8250_cdsp_resource}, - { .compatible = "qcom,sm8250-slpi-pas", .data = &sm8250_slpi_resource}, + { .compatible = "qcom,sm8250-slpi-pas", .data = &sdm845_slpi_resource_init}, { .compatible = "qcom,sm8350-adsp-pas", .data = &sm8350_adsp_resource}, { .compatible = "qcom,sm8350-cdsp-pas", .data = &sm8350_cdsp_resource}, - { .compatible = "qcom,sm8350-slpi-pas", .data = &sm8350_slpi_resource}, + { .compatible = "qcom,sm8350-slpi-pas", .data = &sdm845_slpi_resource_init}, { .compatible = "qcom,sm8350-mpss-pas", .data = &mpss_resource_init}, { .compatible = "qcom,sm8450-adsp-pas", .data = &sm8350_adsp_resource}, { .compatible = "qcom,sm8450-cdsp-pas", .data = &sm8350_cdsp_resource}, - { .compatible = "qcom,sm8450-slpi-pas", .data = &sm8350_slpi_resource}, + { .compatible = "qcom,sm8450-slpi-pas", .data = &sdm845_slpi_resource_init}, { .compatible = "qcom,sm8450-mpss-pas", .data = &sm8450_mpss_resource}, { .compatible = "qcom,sm8550-adsp-pas", .data = &sm8550_adsp_resource}, { .compatible = "qcom,sm8550-cdsp-pas", .data = &sm8550_cdsp_resource}, -- 2.39.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init 2023-03-30 16:46 ` [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init Dylan Van Assche @ 2023-03-30 23:03 ` Konrad Dybcio 0 siblings, 0 replies; 8+ messages in thread From: Konrad Dybcio @ 2023-03-30 23:03 UTC (permalink / raw) To: Dylan Van Assche, Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel On 30.03.2023 18:46, Dylan Van Assche wrote: > SLPI remoteproc initialization is the same for SDM845, SM8150, SM8250, > SM8350 but is duplicated for each compatible. Refactor initialization > structs for these 4 compatibles as a single struct. > > Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > drivers/remoteproc/qcom_q6v5_pas.c | 48 +++++------------------------- > 1 file changed, 8 insertions(+), 40 deletions(-) > > diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c > index c99a20542685..b96020c93e58 100644 > --- a/drivers/remoteproc/qcom_q6v5_pas.c > +++ b/drivers/remoteproc/qcom_q6v5_pas.c > @@ -1014,7 +1014,7 @@ static const struct adsp_data sc8180x_mpss_resource = { > .ssctl_id = 0x12, > }; > > -static const struct adsp_data slpi_resource_init = { > +static const struct adsp_data msm8996_slpi_resource_init = { > .crash_reason_smem = 424, > .firmware_name = "slpi.mdt", > .pas_id = 12, > @@ -1028,7 +1028,7 @@ static const struct adsp_data slpi_resource_init = { > .ssctl_id = 0x16, > }; > > -static const struct adsp_data sm8150_slpi_resource = { > +static const struct adsp_data sdm845_slpi_resource_init = { > .crash_reason_smem = 424, > .firmware_name = "slpi.mdt", > .pas_id = 12, > @@ -1044,38 +1044,6 @@ static const struct adsp_data sm8150_slpi_resource = { > .ssctl_id = 0x16, > }; > > -static const struct adsp_data sm8250_slpi_resource = { > - .crash_reason_smem = 424, > - .firmware_name = "slpi.mdt", > - .pas_id = 12, > - .auto_boot = true, > - .proxy_pd_names = (char*[]){ > - "lcx", > - "lmx", > - NULL > - }, > - .load_state = "slpi", > - .ssr_name = "dsps", > - .sysmon_name = "slpi", > - .ssctl_id = 0x16, > -}; > - > -static const struct adsp_data sm8350_slpi_resource = { > - .crash_reason_smem = 424, > - .firmware_name = "slpi.mdt", > - .pas_id = 12, > - .auto_boot = true, > - .proxy_pd_names = (char*[]){ > - "lcx", > - "lmx", > - NULL > - }, > - .load_state = "slpi", > - .ssr_name = "dsps", > - .sysmon_name = "slpi", > - .ssctl_id = 0x16, > -}; > - > static const struct adsp_data wcss_resource_init = { > .crash_reason_smem = 421, > .firmware_name = "wcnss.mdt", > @@ -1184,9 +1152,9 @@ static const struct of_device_id adsp_of_match[] = { > { .compatible = "qcom,msm8953-adsp-pil", .data = &msm8996_adsp_resource}, > { .compatible = "qcom,msm8974-adsp-pil", .data = &adsp_resource_init}, > { .compatible = "qcom,msm8996-adsp-pil", .data = &msm8996_adsp_resource}, > - { .compatible = "qcom,msm8996-slpi-pil", .data = &slpi_resource_init}, > + { .compatible = "qcom,msm8996-slpi-pil", .data = &msm8996_slpi_resource_init}, > { .compatible = "qcom,msm8998-adsp-pas", .data = &msm8996_adsp_resource}, > - { .compatible = "qcom,msm8998-slpi-pas", .data = &slpi_resource_init}, > + { .compatible = "qcom,msm8998-slpi-pas", .data = &msm8996_slpi_resource_init}, > { .compatible = "qcom,qcs404-adsp-pas", .data = &adsp_resource_init }, > { .compatible = "qcom,qcs404-cdsp-pas", .data = &cdsp_resource_init }, > { .compatible = "qcom,qcs404-wcss-pas", .data = &wcss_resource_init }, > @@ -1211,17 +1179,17 @@ static const struct of_device_id adsp_of_match[] = { > { .compatible = "qcom,sm8150-adsp-pas", .data = &sm8150_adsp_resource}, > { .compatible = "qcom,sm8150-cdsp-pas", .data = &sm8150_cdsp_resource}, > { .compatible = "qcom,sm8150-mpss-pas", .data = &mpss_resource_init}, > - { .compatible = "qcom,sm8150-slpi-pas", .data = &sm8150_slpi_resource}, > + { .compatible = "qcom,sm8150-slpi-pas", .data = &sdm845_slpi_resource_init}, > { .compatible = "qcom,sm8250-adsp-pas", .data = &sm8250_adsp_resource}, > { .compatible = "qcom,sm8250-cdsp-pas", .data = &sm8250_cdsp_resource}, > - { .compatible = "qcom,sm8250-slpi-pas", .data = &sm8250_slpi_resource}, > + { .compatible = "qcom,sm8250-slpi-pas", .data = &sdm845_slpi_resource_init}, > { .compatible = "qcom,sm8350-adsp-pas", .data = &sm8350_adsp_resource}, > { .compatible = "qcom,sm8350-cdsp-pas", .data = &sm8350_cdsp_resource}, > - { .compatible = "qcom,sm8350-slpi-pas", .data = &sm8350_slpi_resource}, > + { .compatible = "qcom,sm8350-slpi-pas", .data = &sdm845_slpi_resource_init}, > { .compatible = "qcom,sm8350-mpss-pas", .data = &mpss_resource_init}, > { .compatible = "qcom,sm8450-adsp-pas", .data = &sm8350_adsp_resource}, > { .compatible = "qcom,sm8450-cdsp-pas", .data = &sm8350_cdsp_resource}, > - { .compatible = "qcom,sm8450-slpi-pas", .data = &sm8350_slpi_resource}, > + { .compatible = "qcom,sm8450-slpi-pas", .data = &sdm845_slpi_resource_init}, > { .compatible = "qcom,sm8450-mpss-pas", .data = &sm8450_mpss_resource}, > { .compatible = "qcom,sm8550-adsp-pas", .data = &sm8550_adsp_resource}, > { .compatible = "qcom,sm8550-cdsp-pas", .data = &sm8550_cdsp_resource}, ^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init Dylan Van Assche @ 2023-03-30 16:46 ` Dylan Van Assche 2023-03-30 23:03 ` Konrad Dybcio 2023-07-15 22:13 ` (subset) [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Bjorn Andersson 2023-07-15 22:23 ` Bjorn Andersson 4 siblings, 1 reply; 8+ messages in thread From: Dylan Van Assche @ 2023-03-30 16:46 UTC (permalink / raw) To: Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel, Dylan Van Assche Add a compatible for the SDM845 SLPI to the Qualcomm remoteproc q6v5_pas driver. The SLPI is the same as in SM8150, SM8250, SM8350, and SM8450, so use the same resource in the driver. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> --- drivers/remoteproc/qcom_q6v5_pas.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c index b96020c93e58..f3a7ae503bd1 100644 --- a/drivers/remoteproc/qcom_q6v5_pas.c +++ b/drivers/remoteproc/qcom_q6v5_pas.c @@ -1169,6 +1169,7 @@ static const struct of_device_id adsp_of_match[] = { { .compatible = "qcom,sdm660-adsp-pas", .data = &adsp_resource_init}, { .compatible = "qcom,sdm845-adsp-pas", .data = &sdm845_adsp_resource_init}, { .compatible = "qcom,sdm845-cdsp-pas", .data = &sdm845_cdsp_resource_init}, + { .compatible = "qcom,sdm845-slpi-pas", .data = &sdm845_slpi_resource_init}, { .compatible = "qcom,sdx55-mpss-pas", .data = &sdx55_mpss_resource}, { .compatible = "qcom,sm6115-adsp-pas", .data = &adsp_resource_init}, { .compatible = "qcom,sm6115-cdsp-pas", .data = &cdsp_resource_init}, -- 2.39.2 ^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible 2023-03-30 16:46 ` [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible Dylan Van Assche @ 2023-03-30 23:03 ` Konrad Dybcio 0 siblings, 0 replies; 8+ messages in thread From: Konrad Dybcio @ 2023-03-30 23:03 UTC (permalink / raw) To: Dylan Van Assche, Andy Gross, Bjorn Andersson, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski Cc: Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel On 30.03.2023 18:46, Dylan Van Assche wrote: > Add a compatible for the SDM845 SLPI to the Qualcomm remoteproc q6v5_pas > driver. The SLPI is the same as in SM8150, SM8250, SM8350, and SM8450, > so use the same resource in the driver. > > Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > drivers/remoteproc/qcom_q6v5_pas.c | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/drivers/remoteproc/qcom_q6v5_pas.c b/drivers/remoteproc/qcom_q6v5_pas.c > index b96020c93e58..f3a7ae503bd1 100644 > --- a/drivers/remoteproc/qcom_q6v5_pas.c > +++ b/drivers/remoteproc/qcom_q6v5_pas.c > @@ -1169,6 +1169,7 @@ static const struct of_device_id adsp_of_match[] = { > { .compatible = "qcom,sdm660-adsp-pas", .data = &adsp_resource_init}, > { .compatible = "qcom,sdm845-adsp-pas", .data = &sdm845_adsp_resource_init}, > { .compatible = "qcom,sdm845-cdsp-pas", .data = &sdm845_cdsp_resource_init}, > + { .compatible = "qcom,sdm845-slpi-pas", .data = &sdm845_slpi_resource_init}, > { .compatible = "qcom,sdx55-mpss-pas", .data = &sdx55_mpss_resource}, > { .compatible = "qcom,sm6115-adsp-pas", .data = &adsp_resource_init}, > { .compatible = "qcom,sm6115-cdsp-pas", .data = &cdsp_resource_init}, ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: (subset) [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche ` (2 preceding siblings ...) 2023-03-30 16:46 ` [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible Dylan Van Assche @ 2023-07-15 22:13 ` Bjorn Andersson 2023-07-15 22:23 ` Bjorn Andersson 4 siblings, 0 replies; 8+ messages in thread From: Bjorn Andersson @ 2023-07-15 22:13 UTC (permalink / raw) To: Andy Gross, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski, Dylan Van Assche Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel On Thu, 30 Mar 2023 18:46:30 +0200, Dylan Van Assche wrote: > * About * > > The Qualcomm SDM845 SoC has a separate SLPI (Sensor Low Power Island) > DSP for sensors connected to the SoC which is responsible for exposing > sensors to userspace, power saving, and other features. > While sensors are connected to GPIOs of the SoC, they cannot be used > because the hypervisor blocks direct access to the sensors, thus the > DSP must be used to access any sensor on this SoC. The SLPI DSP uses a > GLink edge (dsps) to communicate with the host and has a FastRPC interface > to load files from the host filesystem such as sensor configuration files. > The FastRPC interface does not use regular FastRPC Compute Banks > but instead uses an allocated CMA region through which communication happens. > > [...] Applied, thanks! [1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible commit: 242a626870eb453934b75749f8dbab997556b555 [2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init commit: 637e98bfe20b2c6866cd79b8d487430af09dc8ac Best regards, -- Bjorn Andersson <andersson@kernel.org> ^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche ` (3 preceding siblings ...) 2023-07-15 22:13 ` (subset) [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Bjorn Andersson @ 2023-07-15 22:23 ` Bjorn Andersson 4 siblings, 0 replies; 8+ messages in thread From: Bjorn Andersson @ 2023-07-15 22:23 UTC (permalink / raw) To: Andy Gross, Mathieu Poirier, Rob Herring, Krzysztof Kozlowski, Dylan Van Assche Cc: Konrad Dybcio, Manivannan Sadhasivam, linux-arm-msm, linux-remoteproc, devicetree, linux-kernel, ~postmarketos/upstreaming, phone-devel On Thu, 30 Mar 2023 18:46:30 +0200, Dylan Van Assche wrote: > * About * > > The Qualcomm SDM845 SoC has a separate SLPI (Sensor Low Power Island) > DSP for sensors connected to the SoC which is responsible for exposing > sensors to userspace, power saving, and other features. > While sensors are connected to GPIOs of the SoC, they cannot be used > because the hypervisor blocks direct access to the sensors, thus the > DSP must be used to access any sensor on this SoC. The SLPI DSP uses a > GLink edge (dsps) to communicate with the host and has a FastRPC interface > to load files from the host filesystem such as sensor configuration files. > The FastRPC interface does not use regular FastRPC Compute Banks > but instead uses an allocated CMA region through which communication happens. > > [...] Applied, thanks! [1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible commit: 242a626870eb453934b75749f8dbab997556b555 [2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init commit: 637e98bfe20b2c6866cd79b8d487430af09dc8ac [3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible commit: ba3125b47016cdc66454cf720f899b3bf806debc Best regards, -- Bjorn Andersson <andersson@kernel.org> ^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2023-07-15 22:19 UTC | newest] Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2023-03-30 16:46 [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 1/3] dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible Dylan Van Assche 2023-03-30 16:46 ` [PATCH v3 2/3] remoteproc: qcom: pas: refactor SLPI remoteproc init Dylan Van Assche 2023-03-30 23:03 ` Konrad Dybcio 2023-03-30 16:46 ` [PATCH v3 3/3] remoteproc: qcom: pas: add SDM845 SLPI compatible Dylan Van Assche 2023-03-30 23:03 ` Konrad Dybcio 2023-07-15 22:13 ` (subset) [PATCH v3 0/3] remoteproc: qcom: pas: Support SDM845 SLPI Bjorn Andersson 2023-07-15 22:23 ` Bjorn Andersson
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).