linux-renesas-soc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
To: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Rob Herring <robh+dt@kernel.org>,
	Jonathan Cameron <jic23@kernel.org>,
	Lars-Peter Clausen <lars@metafoo.de>,
	Magnus Damm <magnus.damm@gmail.com>,
	Alexandru Ardelean <aardelean@deviqon.com>,
	linux-iio <linux-iio@vger.kernel.org>,
	"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS" 
	<devicetree@vger.kernel.org>,
	Linux-Renesas <linux-renesas-soc@vger.kernel.org>,
	LKML <linux-kernel@vger.kernel.org>,
	Biju Das <biju.das.jz@bp.renesas.com>
Subject: Re: [PATCH v3 2/3] iio: adc: Add driver for Renesas RZ/G2L A/D converter
Date: Tue, 27 Jul 2021 09:02:10 +0100	[thread overview]
Message-ID: <CA+V-a8shgfxffdOTj0cyxz36XVxGxUkq1obPJNOSc94BKUWung@mail.gmail.com> (raw)
In-Reply-To: <f23358e3e040cc8522b259669ec61a22c5439394.camel@pengutronix.de>

Hi Philipp,

Thank you for the review.

On Tue, Jul 27, 2021 at 8:13 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
>
> Hi Prabhakar,
>
> On Mon, 2021-07-26 at 19:28 +0100, Lad Prabhakar wrote:
> > Add ADC driver support for Renesas RZ/G2L A/D converter in SW
> > trigger mode.
> >
> > A/D Converter block is a successive approximation analog-to-digital
> > converter with a 12-bit accuracy and supports a maximum of 8 input
> > channels.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> > ---
> >  MAINTAINERS                 |   8 +
> >  drivers/iio/adc/Kconfig     |  10 +
> >  drivers/iio/adc/Makefile    |   1 +
> >  drivers/iio/adc/rzg2l_adc.c | 595 ++++++++++++++++++++++++++++++++++++
> >  4 files changed, 614 insertions(+)
> >  create mode 100644 drivers/iio/adc/rzg2l_adc.c
> >
> [...]
> > diff --git a/drivers/iio/adc/rzg2l_adc.c b/drivers/iio/adc/rzg2l_adc.c
> > new file mode 100644
> > index 000000000000..d05a3208ff9d
> > --- /dev/null
> > +++ b/drivers/iio/adc/rzg2l_adc.c
> > @@ -0,0 +1,595 @@
> [...]
> > +static void rzg2l_adc_pm_runtime_disable(void *data)
> > +{
> > +     struct iio_dev *indio_dev = data;
> > +
> > +     pm_runtime_disable(indio_dev->dev.parent);
> > +}
> > +
> > +static void rzg2l_adc_reset_assert(void *data)
> > +{
> > +     struct reset_control *reset = data;
> > +
> > +     reset_control_assert(reset);
> > +}
> > +
> > +static int rzg2l_adc_probe(struct platform_device *pdev)
> > +{
> > +     struct device *dev = &pdev->dev;
> > +     struct iio_dev *indio_dev;
> > +     struct rzg2l_adc *adc;
> > +     int ret;
> > +     int irq;
> > +
> > +     indio_dev = devm_iio_device_alloc(dev, sizeof(*adc));
> > +     if (!indio_dev)
> > +             return -ENOMEM;
> > +
> > +     adc = iio_priv(indio_dev);
> > +
> > +     ret = rzg2l_adc_parse_properties(pdev, adc);
> > +     if (ret)
> > +             return ret;
> > +
> > +     adc->base = devm_platform_ioremap_resource(pdev, 0);
> > +     if (IS_ERR(adc->base))
> > +             return PTR_ERR(adc->base);
> > +
> > +     irq = platform_get_irq(pdev, 0);
> > +     if (irq < 0) {
> > +             dev_err(dev, "no irq resource\n");
> > +             return irq;
> > +     }
> > +
> > +     adc->pclk = devm_clk_get(dev, "pclk");
> > +     if (IS_ERR(adc->pclk)) {
> > +             dev_err(dev, "Failed to get pclk");
> > +             return PTR_ERR(adc->pclk);
> > +     }
> > +
> > +     adc->adclk = devm_clk_get(dev, "adclk");
> > +     if (IS_ERR(adc->adclk)) {
> > +             dev_err(dev, "Failed to get adclk");
> > +             return PTR_ERR(adc->adclk);
> > +     }
> > +
> > +     adc->adrstn = devm_reset_control_get_exclusive(dev, "adrst-n");
> > +     if (IS_ERR(adc->adrstn)) {
> > +             dev_err(dev, "failed to get adrstn\n");
> > +             return PTR_ERR(adc->adrstn);
> > +     }
>
> I'd request the "presetn" control up here, so if that fails we don't
> touch the "adrst-n" reset line.
>
Ok will move the devm_reset_control_get_exclusive() call for presetn here.

> > +     ret = devm_add_action_or_reset(&pdev->dev,
> > +                                    rzg2l_adc_reset_assert, adc->adrstn);
> > +     if (ret) {
> > +             dev_err(&pdev->dev, "failed to register adrstn assert devm action, %d\n",
> > +                     ret);
> > +             return ret;
> > +     }
>
> This is the wrong way around. Installing devres actions should be done
> after the thing they are supposed to revert in case of error. You should
> move this down below the reset_control_deassert(adc->adrstn).
>
Ouch my understanding was, there won't be any harm in asserting the
reset line. Agree with will move this below
reset_control_deassert(adc->adrstn).

> > +
> > +     adc->presetn = devm_reset_control_get_exclusive(dev, "presetn");
> > +     if (IS_ERR(adc->presetn)) {
> > +             dev_err(dev, "failed to get presetn\n");
> > +             return PTR_ERR(adc->presetn);
> > +     }
> > +
> > +     ret = devm_add_action_or_reset(&pdev->dev,
> > +                                    rzg2l_adc_reset_assert, adc->presetn);
> > +     if (ret) {
> > +             dev_err(&pdev->dev, "failed to register presetn assert devm action, %d\n",
> > +                     ret);
> > +             return ret;
> > +     }
>
> Same as above, this belongs after the presetn deassert below.
>
Agreed.

> > +
> > +     ret = reset_control_deassert(adc->adrstn);
> > +     if (ret) {
> > +             dev_err(&pdev->dev, "failed to deassert adrstn pin, %d\n", ret);
> > +             return ret;
> > +     }
>
> Here is the place to install the adrstn assert action.
>
Agreed will move the devres action here.

> > +     ret = reset_control_deassert(adc->presetn);
> > +     if (ret) {
> > +             dev_err(&pdev->dev, "failed to deassert presetn pin, %d\n", ret);
> > +             return ret;
> > +     }
>
> And here is the place to install the presetn assert action.
>
Agreed will move the devres action here.

Cheers,
Prabhakar

> regards
> Philipp

  reply	other threads:[~2021-07-27  8:03 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-07-26 18:28 [PATCH v3 0/3] Renesas RZ/G2L ADC driver support Lad Prabhakar
2021-07-26 18:28 ` [PATCH v3 1/3] dt-bindings: iio: adc: Add binding documentation for Renesas RZ/G2L A/D converter Lad Prabhakar
2021-07-26 21:42   ` Rob Herring
2021-07-27  8:06     ` Lad, Prabhakar
2021-07-27 20:30   ` Rob Herring
2021-07-26 18:28 ` [PATCH v3 2/3] iio: adc: Add driver " Lad Prabhakar
2021-07-27  7:13   ` Philipp Zabel
2021-07-27  8:02     ` Lad, Prabhakar [this message]
2021-07-27  8:13       ` Philipp Zabel
2021-07-27  8:54         ` Lad, Prabhakar
2021-07-31 17:11   ` Jonathan Cameron
2021-07-31 18:31     ` Lad, Prabhakar
2021-08-01 16:59       ` Jonathan Cameron
2021-08-01 19:51         ` Lad, Prabhakar
2021-07-26 18:28 ` [PATCH v3 3/3] arm64: dts: renesas: r9a07g044: Add ADC node Lad Prabhakar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CA+V-a8shgfxffdOTj0cyxz36XVxGxUkq1obPJNOSc94BKUWung@mail.gmail.com \
    --to=prabhakar.csengg@gmail.com \
    --cc=aardelean@deviqon.com \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=devicetree@vger.kernel.org \
    --cc=geert+renesas@glider.be \
    --cc=jic23@kernel.org \
    --cc=lars@metafoo.de \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=magnus.damm@gmail.com \
    --cc=p.zabel@pengutronix.de \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=robh+dt@kernel.org \
    --subject='Re: [PATCH v3 2/3] iio: adc: Add driver for Renesas RZ/G2L A/D converter' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).