From: Atish Patra <atish.patra@wdc.com>
To: Kevin Hilman <khilman@baylibre.com>,
Paul Walmsley <paul.walmsley@sifive.com>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"linux-riscv@lists.infradead.org"
<linux-riscv@lists.infradead.org>
Subject: Re: [PATCH v3 0/5] arch: riscv: add board and SoC DT file support
Date: Thu, 6 Jun 2019 16:15:40 -0700 [thread overview]
Message-ID: <05010310-baa2-c711-cb54-96a9138f582a@wdc.com> (raw)
In-Reply-To: <7h36kogchx.fsf@baylibre.com>
On 6/5/19 10:37 AM, Kevin Hilman wrote:
> Hi Paul,
>
> Paul Walmsley <paul.walmsley@sifive.com> writes:
>
>> Add support for building flattened DT files from DT source files under
>> arch/riscv/boot/dts. Follow existing kernel precedent from other SoC
>> architectures. Start our board support by adding initial support for
>> the SiFive FU540 SoC and the first development board that uses it, the
>> SiFive HiFive Unleashed A00.
>>
>> This third version of the patch set adds I2C data for the chip,
>> incorporates all remaining changes that riscv-pk was making
>> automatically, and addresses a comment from Rob Herring
>> <robh@kernel.org>.
>>
>> Boot-tested on v5.2-rc1 on a HiFive Unleashed A00 board, using the
>> BBL and open-source FSBL, with modifications to pass in the DTB
>> file generated by these patches.
>
> Tested this series on top of v5.2-rc3 on HiFive Unleashed board using
> OpenSBI + mainline u-boot (master branch as of today).
>
> Tested-by: Kevin Hilman <khilman@baylibre.com>
>
>> This patch series can be found, along with the PRCI patch set
>> and the DT macro prerequisite patch, at:
>>
>> https://github.com/sifive/riscv-linux/tree/dev/paulw/dts-v5.2-rc1
>
> nit: I only see this series in that branch, not any of the prerequisite
> patches you mentioned, which made me assume I could this series alone on
> top of v5.2-rc3, which worked just fine.
>
I tried only this series on top of v5.2-rc3. Kernel boots file with DT
updated via U-Boot. But networking didn't come up.
Do you have networking up after the boot? If yes, can you please share
the config.
> Kevin
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv
>
--
Regards,
Atish
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2019-06-06 23:19 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-02 8:04 [PATCH v3 0/5] arch: riscv: add board and SoC DT file support Paul Walmsley
2019-06-02 8:04 ` [PATCH v3 1/5] arch: riscv: add support for building DTB files from DT source data Paul Walmsley
2019-06-04 14:37 ` Loys Ollivier
2019-06-07 5:12 ` Paul Walmsley
2019-06-07 9:49 ` Loys Ollivier
2019-06-08 17:56 ` Palmer Dabbelt
2019-06-09 5:50 ` Paul Walmsley
2019-06-09 7:49 ` Christoph Hellwig
2019-06-02 8:04 ` [PATCH v3 2/5] dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540 Paul Walmsley
2019-06-10 21:44 ` Rob Herring
2019-06-16 18:39 ` Paul Walmsley
2019-06-02 8:04 ` [PATCH v3 3/5] dt-bindings: riscv: convert cpu binding to json-schema Paul Walmsley
2019-06-02 8:04 ` [PATCH v3 4/5] riscv: dts: add initial support for the SiFive FU540-C000 SoC Paul Walmsley
2019-06-04 14:38 ` Loys Ollivier
2019-06-02 8:05 ` [PATCH v3 5/5] riscv: dts: add initial board data for the SiFive HiFive Unleashed Paul Walmsley
2019-06-04 14:41 ` Loys Ollivier
2019-06-09 6:18 ` Antony Pavlov
2019-06-16 18:36 ` Paul Walmsley
2019-06-04 14:31 ` [PATCH v3 0/5] arch: riscv: add board and SoC DT file support Loys Ollivier
2019-06-07 5:14 ` Paul Walmsley
2019-06-05 17:36 ` Kevin Hilman
2019-06-06 23:15 ` Atish Patra [this message]
2019-06-07 16:51 ` Kevin Hilman
2019-06-07 17:58 ` Atish Patra
2019-06-07 20:55 ` Auer, Lukas
2019-06-07 5:18 ` Paul Walmsley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=05010310-baa2-c711-cb54-96a9138f582a@wdc.com \
--to=atish.patra@wdc.com \
--cc=khilman@baylibre.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=paul.walmsley@sifive.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).