* [PATCH v3 1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S
@ 2020-09-20 15:45 David Bauer
2020-09-20 15:45 ` [PATCH v3 2/2] rockchip: rk3328: Add support " David Bauer
2020-09-22 14:06 ` [PATCH v3 1/2] dt-bindings: Add doc " Heiko Stuebner
0 siblings, 2 replies; 3+ messages in thread
From: David Bauer @ 2020-09-20 15:45 UTC (permalink / raw)
To: robh+dt, heiko, andy.yan, jagan, jbx6244, robin.murphy,
kever.yang, m.reichl, devicetree, linux-arm-kernel,
linux-rockchip
Cc: Rob Herring
Add devicetree binding documentation for the FriendlyARM NanoPi R2S.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index db2e35796795..61722b9ffa9a 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -104,6 +104,11 @@ properties:
- firefly,roc-rk3399-pc-mezzanine
- const: rockchip,rk3399
+ - description: FriendlyElec NanoPi R2S
+ items:
+ - const: friendlyarm,nanopi-r2s
+ - const: rockchip,rk3328
+
- description: FriendlyElec NanoPi4 series boards
items:
- enum:
--
2.28.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v3 2/2] rockchip: rk3328: Add support for FriendlyARM NanoPi R2S
2020-09-20 15:45 [PATCH v3 1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S David Bauer
@ 2020-09-20 15:45 ` David Bauer
2020-09-22 14:06 ` [PATCH v3 1/2] dt-bindings: Add doc " Heiko Stuebner
1 sibling, 0 replies; 3+ messages in thread
From: David Bauer @ 2020-09-20 15:45 UTC (permalink / raw)
To: robh+dt, heiko, andy.yan, jagan, jbx6244, robin.murphy,
kever.yang, m.reichl, devicetree, linux-arm-kernel,
linux-rockchip
This adds support for the NanoPi R2S from FriendlyARM.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
---
Changes in v3:
- Rename gmac-clock node
- Various sorting fixes
- Rename label for reset button
- Fix LED pinctrl bracketing
- Fix ethernet-phy node name
- add dr_mode property to OTG node
Changes in v2:
- Change model name to FriendlyElec
- Enable SD UHS modes
- Add startup delay to SDIO regulator to improve
issues reported with some cards
- Fix PMIC interrupt pin
- Add pinctrl node for ethernet-PHY
- Fix various formatting issues
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3328-nanopi-r2s.dts | 368 ++++++++++++++++++
2 files changed, 369 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index b87b1f773083..20055c51e150 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
new file mode 100644
index 000000000000..b9daf89e950a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 David Bauer <mail@david-bauer.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "rk3328.dtsi"
+
+/ {
+ model = "FriendlyElec NanoPi R2S";
+ compatible = "friendlyarm,nanopi-r2s", "rockchip,rk3328";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clk: gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clk";
+ #clock-cells = <0>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&reset_button_pin>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <50>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
+ pinctrl-names = "default";
+
+ lan_led: led-0 {
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:green:lan";
+ };
+
+ sys_led: led-1 {
+ gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:red:sys";
+ };
+
+ wan_led: led-2 {
+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+ label = "nanopi-r2s:green:wan";
+ };
+ };
+
+ vcc_io_sdio: sdmmcio-regulator {
+ compatible = "regulator-gpio";
+ enable-active-high;
+ gpios = <&gpio1 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&sdio_vcc_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_io_sdio";
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-settling-time-us = <5000>;
+ regulator-type = "voltage";
+ startup-delay-us = <2000>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdmmc0m1_gpio>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_sd";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io_33>;
+ };
+
+ vdd_5v: vdd-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+ clock_in_out = "input";
+ phy-handle = <&rtl8211e>;
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_io_33>;
+ pinctrl-0 = <&rgmiim1_pins>;
+ pinctrl-names = "default";
+ rx_delay = <0x18>;
+ snps,aal;
+ tx_delay = <0x24>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtl8211e: ethernet-phy@1 {
+ reg = <1>;
+ pinctrl-0 = <ð_phy_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&pmic_int_l>;
+ pinctrl-names = "default";
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vdd_5v>;
+ vcc2-supply = <&vdd_5v>;
+ vcc3-supply = <&vdd_5v>;
+ vcc4-supply = <&vdd_5v>;
+ vcc5-supply = <&vcc_io_33>;
+ vcc6-supply = <&vdd_5v>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io_33: DCDC_REG4 {
+ regulator-name = "vcc_io_33";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+};
+
+&io_domains {
+ pmuio-supply = <&vcc_io_33>;
+ vccio1-supply = <&vcc_io_33>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_io_sdio>;
+ vccio4-supply = <&vcc_18>;
+ vccio5-supply = <&vcc_io_33>;
+ vccio6-supply = <&vcc_io_33>;
+ status = "okay";
+};
+
+&pinctrl {
+ button {
+ reset_button_pin: reset-button-pin {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ethernet-phy {
+ eth_phy_reset_pin: eth-phy-reset-pin {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ lan_led_pin: lan-led-pin {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ sys_led_pin: sys-led-pin {
+ rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wan_led_pin: wan-led-pin {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sd {
+ sdio_vcc_pin: sdio-vcc-pin {
+ rockchip,pins = <1 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+ pinctrl-names = "default";
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vcc_io_sdio>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
--
2.28.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S
2020-09-20 15:45 [PATCH v3 1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S David Bauer
2020-09-20 15:45 ` [PATCH v3 2/2] rockchip: rk3328: Add support " David Bauer
@ 2020-09-22 14:06 ` Heiko Stuebner
1 sibling, 0 replies; 3+ messages in thread
From: Heiko Stuebner @ 2020-09-22 14:06 UTC (permalink / raw)
To: devicetree, m.reichl, David Bauer, kever.yang, linux-arm-kernel,
robin.murphy, jbx6244, robh+dt, andy.yan, jagan, linux-rockchip
Cc: Rob Herring, Heiko Stuebner
On Sun, 20 Sep 2020 17:45:27 +0200, David Bauer wrote:
> Add devicetree binding documentation for the FriendlyARM NanoPi R2S.
Applied, thanks!
[1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S
commit: 8cfcf3279419acbf2d2c471262bfb18d9e175fc9
[2/2] arm64: dts: rockchip: Add support for FriendlyARM NanoPi R2S
commit: f1ec83f880dbeaceb10d33c40c47aa1769b787e8
After adapting to the renamed pinctrl name.
Best regards,
--
Heiko Stuebner <heiko@sntech.de>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2020-09-22 14:06 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-09-20 15:45 [PATCH v3 1/2] dt-bindings: Add doc for FriendlyARM NanoPi R2S David Bauer
2020-09-20 15:45 ` [PATCH v3 2/2] rockchip: rk3328: Add support " David Bauer
2020-09-22 14:06 ` [PATCH v3 1/2] dt-bindings: Add doc " Heiko Stuebner
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).