Linux-RTC Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v12 00/10] Support ROHM BD71828 PMIC
@ 2020-01-20  9:12 Matti Vaittinen
  2020-01-20  9:12 ` [PATCH v12 01/10] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
                   ` (10 more replies)
  0 siblings, 11 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:12 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

Patch series introducing support for ROHM BD71828 PMIC

ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs. All
regulators can be controlled individually via I2C. Bucks 1,2,6 and
7 can also be assigned to a "regulator group" controlled by run-levels.
Eg. Run level specific voltages and enable/disable statuses for each of
these bucks can be set via register interface. The buck run-level group
assignment (selection if buck is to be controlled individually or via
run-levels) can be changed at run-time via I2C.

This patch series brings only the basic support for controlling
regulators individually via I2C.

In addition to the bucks and LDOs there are:

- The usual clk gate
- 4 IO pins (mostly usable as GPO or tied to specific purpose)
- power button support
- RTC
- two LEDs
- battery charger
- HALL sensor input

This patch series adds support to regulators, clk, RTC and GPIOs.

Power-supply driver for charger or LED driver is not included in this series.

Changelog v12:
  - removed input: tag from MFD gpio-keys patch
  - dropped LED patches for now.

Changelog v11:
  - converted a macro to enum member as was requested by Lee.

Changelog v10:
  - Split RTC patch to a BD70528 fix (which hopefully goes to 5.4) and to
    BD71828 support

Changelog v9: (Changes suggested by Lee)
  - Added kerneldoc to struct rohm_dvs_config
  - cleaned few comments
  - updated copyright date
  - renamed variable 'mfd' to 'parent'.

Changelog v8:
  LEDs:
    - Fixed bunch of typos.
    - Corrected the commit message which errorneously contained the
      'leds-compatible' which I dropped in favour of match_property.
    - use max_brightness instead of LED_FULL if it is given when
      handling the default_state, "on".
    - clean fwnode_owned at the end of unsuccessful registration or
      at the end of deregistration.
    - fix the accidental linuxdoc comment.
    - rename led_find_fwnode to led_get_fwnode as it increases refcount.

Changelog v7:
  - Rebased on top of v5.5-rc2
  - Dropped already applied patches
    - basic regulator support (in regulator tree now)
    - regulator dt-bindings (in regulator tree now)
    - gpio devm function documentation (in GPIO tree now)
  - Dropped new devm-variant of gpio_array getting for MFD sub-devices who
    have consumer information in parent DT node as gpio consumer was
    dropped from the series
  - removed extra line-breaks from MFD driver and Makefile
  - fixed RTC patch subject line (added missing colon)
  - included a patch which adds compatible for ROHM BD71850 PMIC

Changelog v6:
  Rebased on top of v5.5-rc1
  LED core:
    - Do new fw-node look-up only if the new match data is given. That
      way behaviour for existing drivers is not changed
    - Handle generic LED properties by core only if explisitly requested
      in init-data. That way behaviour for existing drivers is not changed
      until they are verified to work.
  BD71828 LEDs:
    - Fix module loading by adding "dummy" of_device_id table.
  DT bindings:
    All:
    - Remove regulator run-level properties as run-level support was
      dropped for now.
    - Change SPDX to dual lisence
    LED:
    - added select: false
    - replace oneOf + const by enum
    Regulator:
    - remove forgotten comments
    - comment indenting
    MFD:
    - remove unnecessary descriptions
  Regulators:
    - Dropped patch 12 with run-level controls
    - Dropped unnecessary ramp_delay_supported() - ram_delay ops were
      already only filled for DVS bucks.
  GPIO:
    - rename internal function.
  RTC:
    - Added missing blank line
  
Changelog v5:
  Only LED patch (patch 15) changed, rest as in v4.
  LED:
    - Fixed issues reported by Dan Carpenter and kbuild-bot static
      analysis.
Changelog v4 (first non RFC):
  General:
    - Changed subdevice loading and chip version identification to use
      platform ID.
    - License identifiers changed to GPL-2.0-only
  MFD:
    - Styling fixes mostly
  DT-Bindings:
    - a few more checks as suggested by Rob Herring.
    - Order of DT patches changed.
    - me as maintainer
    - standard units to new properties (microvolts, ohms)
    - runlevel values in an array
  LED:
    - BD71828 driver added (back)
      - Added DT support
    - Added LED DT node lookup in led framework when init_data is given
      with DT node match information.
    - Added common property parsing for default-state and
      default-trigger.
  Regulators:
    - dropped sysfs interfaces
    - fixed module unload/reload by binding gpio consumer information to
      regulator device not to MFD.
  GPIO:
    - Added devm_gpiod_get_parent_array
    - added few missing devm functions to documentation

Changelog v3:
  DT-Bindings:
    - yamlify
    - add LED binding doc
  CLK:
    - Move clk register definitions from MFD headers to clk driver
  GPIO:
    - Add generic direction define and use it.
  LED:
    - Drop LED driver from the series (for now).

Changelog v2: Mainly RTC and GPIO fixes suggested by Alexandre and Bartosz
  General:
    -Patch ordering changed to provide dt binding documents right after the
     MFD core.
  DT-Bindings for regulators (Patch 3)
    -Fix typo in PMIC model number
  RTC (patch 11)
    -Reverted renaming in order to reduce patch size.
    -Reworded commit message
  BD71828 regulator (patch 7)
    -Add MODULE_ALIAS
  GPIO (patch 12)
    -Remove file-name from comment
    -prefix IN and OUT defines with chip type
    -improved documentation for the INPUT only pin.
    -removed empty left-over function
    -removed unnecessary #ifdef CONFIG_OF_GPIO
    -removed unnecessary error print
    -Add MODULE_ALIAS

Patch 1:
        dt-bindings for LEDs on BD71828 PMIC
Patch 2:
	dt-bindings for BD71828 PMIC
Patch 3:
	Convert rohm PMICs with common sub-devices to use platform_
	device_id to match MFD sub-devices
Patch 4:
	Add compatible for BD71850
Patch 5:
        BD71828 MFD core.
Patch 6:
	Power button support using GPIO keys.
Patch 7:
        CLK gate support using existing clk-bd718x7
Patch 8:
        Split existing bd718x7 regulator driver to generic ROHM dt
        parsing portion (used by more than one ROHM drivers) and
        bd718x8 specific parts
Patch 9:
        Fix BD70528 RTC HOUR mask
Patch 10:
        Support BD71828 RTC block using BD70528 RTC driver
Patch 11:
        Allow control of GP(I)O pins on BD71828 via GPIO subsystem

---


Matti Vaittinen (10):
  dt-bindings: leds: ROHM BD71282 PMIC LED driver
  dt-bindings: mfd: Document ROHM BD71828 bindings
  mfd: rohm PMICs - use platform_device_id to match MFD sub-devices
  mfd: bd718x7: Add compatible for BD71850
  mfd: bd71828: Support ROHM BD71828 PMIC - core
  mfd: bd71828: Add power-key support
  clk: bd718x7: Support ROHM BD71828 clk block
  regulator: bd718x7: Split driver to common and bd718x7 specific parts
  mfd: bd70528: Fix hour register mask
  rtc: bd70528: add BD71828 support

 .../bindings/leds/rohm,bd71828-leds.yaml      |  52 +++
 .../bindings/mfd/rohm,bd71828-pmic.yaml       | 193 ++++++++
 drivers/clk/Kconfig                           |   6 +-
 drivers/clk/clk-bd718x7.c                     |  50 ++-
 drivers/mfd/Kconfig                           |  15 +
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/rohm-bd70528.c                    |   3 +-
 drivers/mfd/rohm-bd71828.c                    | 344 ++++++++++++++
 drivers/mfd/rohm-bd718x7.c                    |  43 +-
 drivers/regulator/Kconfig                     |   4 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/bd718x7-regulator.c         | 200 +++------
 drivers/regulator/rohm-regulator.c            |  95 ++++
 drivers/rtc/Kconfig                           |   3 +-
 drivers/rtc/rtc-bd70528.c                     | 220 +++++++--
 include/linux/mfd/rohm-bd70528.h              |  19 +-
 include/linux/mfd/rohm-bd71828.h              | 423 ++++++++++++++++++
 include/linux/mfd/rohm-bd718x7.h              |   6 -
 include/linux/mfd/rohm-generic.h              |  70 ++-
 include/linux/mfd/rohm-shared.h               |  21 +
 20 files changed, 1546 insertions(+), 223 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
 create mode 100644 drivers/mfd/rohm-bd71828.c
 create mode 100644 drivers/regulator/rohm-regulator.c
 create mode 100644 include/linux/mfd/rohm-bd71828.h
 create mode 100644 include/linux/mfd/rohm-shared.h


base-commit: b3a987b0264d ("Linux 5.5-rc6")
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 01/10] dt-bindings: leds: ROHM BD71282 PMIC LED driver
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
@ 2020-01-20  9:12 ` Matti Vaittinen
  2020-01-20  9:13 ` [PATCH v12 02/10] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
                   ` (9 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:12 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

Document ROHM BD71828 PMIC LED driver device tree bindings.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 .../bindings/leds/rohm,bd71828-leds.yaml      | 52 +++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml

diff --git a/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml b/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
new file mode 100644
index 000000000000..b50f4bcc98f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/rohm,bd71828-leds.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/rohm,bd71828-leds.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit LED driver
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  This module is part of the ROHM BD71828 MFD device. For more details
+  see Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml.
+
+  The LED controller is represented as a sub-node of the PMIC node on the device
+  tree.
+
+  The device has two LED outputs referred as GRNLED and AMBLED in data-sheet.
+
+select: false
+
+properties:
+  compatible:
+    const: rohm,bd71828-leds
+
+patternProperties:
+  "^led-[1-2]$":
+    type: object
+    description:
+      Properties for a single LED.
+    properties:
+      #allOf:
+        #- $ref: "common.yaml#"
+      rohm,led-compatible:
+        description: LED identification string
+        allOf:
+          - $ref: "/schemas/types.yaml#/definitions/string"
+          - enum:
+            - bd71828-ambled
+            - bd71828-grnled
+      function:
+        description:
+          Purpose of LED as defined in dt-bindings/leds/common.h
+        $ref: "/schemas/types.yaml#/definitions/string"
+      color:
+        description:
+          LED colour as defined in dt-bindings/leds/common.h
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+required:
+  - compatible
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 02/10] dt-bindings: mfd: Document ROHM BD71828 bindings
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
  2020-01-20  9:12 ` [PATCH v12 01/10] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
@ 2020-01-20  9:13 ` Matti Vaittinen
  2020-01-20  9:17 ` [PATCH v12 03/10] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
                   ` (8 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:13 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
a real-time clock (RTC), 3 GPO/regulator control pins, HALL input
and a 32.768 kHz clock gate.

Document the dt bindings drivers are using.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/mfd/rohm,bd71828-pmic.yaml       | 193 ++++++++++++++++++
 1 file changed, 193 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml

diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
new file mode 100644
index 000000000000..4fbb9e734284
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
@@ -0,0 +1,193 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rohm,bd71828-pmic.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD71828 Power Management Integrated Circuit bindings
+
+maintainers:
+  - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
+
+description: |
+  BD71828GW is a single-chip power management IC for battery-powered portable
+  devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
+  single-cell linear charger. Also included is a Coulomb counter, a real-time
+  clock (RTC), and a 32.768 kHz clock gate.
+
+properties:
+  compatible:
+    const: rohm,bd71828
+
+  reg:
+    description:
+      I2C slave address.
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      The first cell is the pin number and the second cell is used to specify
+      flags. See ../gpio/gpio.txt for more information.
+
+  clocks:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 0
+
+  rohm,charger-sense-resistor-ohms:
+    minimum: 10000000
+    maximum: 50000000
+    description: |
+      BD71827 and BD71828 have SAR ADC for measuring charging currents.
+      External sense resistor (RSENSE in data sheet) should be used. If some
+      other but 30MOhm resistor is used the resistance value should be given
+      here in Ohms.
+
+  regulators:
+    $ref: ../regulator/rohm,bd71828-regulator.yaml
+    description:
+      List of child nodes that specify the regulators.
+
+  leds:
+    $ref: ../leds/rohm,bd71828-leds.yaml
+
+  gpio-reserved-ranges:
+    description: |
+      Usage of BD71828 GPIO pins can be changed via OTP. This property can be
+      used to mark the pins which should not be configured for GPIO. Please see
+      the ../gpio/gpio.txt for more information.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - "#clock-cells"
+  - regulators
+  - gpio-controller
+  - "#gpio-cells"
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/leds/common.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pmic: pmic@4b {
+            compatible = "rohm,bd71828";
+            reg = <0x4b>;
+
+            interrupt-parent = <&gpio1>;
+            interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+            clocks = <&osc 0>;
+            #clock-cells = <0>;
+            clock-output-names = "bd71828-32k-out";
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-reserved-ranges = <0 1>, <2 1>;
+
+            rohm,charger-sense-resistor-ohms = <10000000>;
+
+            regulators {
+                buck1: BUCK1 {
+                    regulator-name = "buck1";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck2: BUCK2 {
+                    regulator-name = "buck2";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck3: BUCK3 {
+                    regulator-name = "buck3";
+                    regulator-min-microvolt = <1200000>;
+                    regulator-max-microvolt = <2000000>;
+                };
+                buck4: BUCK4 {
+                    regulator-name = "buck4";
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                buck5: BUCK5 {
+                    regulator-name = "buck5";
+                    regulator-min-microvolt = <2500000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                buck6: BUCK6 {
+                    regulator-name = "buck6";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                buck7: BUCK7 {
+                    regulator-name = "buck7";
+                    regulator-min-microvolt = <500000>;
+                    regulator-max-microvolt = <2000000>;
+                    regulator-ramp-delay = <2500>;
+                };
+                ldo1: LDO1 {
+                    regulator-name = "ldo1";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo2: LDO2 {
+                    regulator-name = "ldo2";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo3: LDO3 {
+                    regulator-name = "ldo3";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo4: LDO4 {
+                    regulator-name = "ldo4";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo5: LDO5 {
+                    regulator-name = "ldo5";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+                ldo6: LDO6 {
+                    regulator-name = "ldo6";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                };
+                ldo7_reg: LDO7 {
+                    regulator-name = "ldo7";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <3300000>;
+                };
+            };
+
+            leds {
+                compatible = "rohm,bd71828-leds";
+
+                led-1 {
+                    rohm,led-compatible = "bd71828-grnled";
+                    function = LED_FUNCTION_INDICATOR;
+                    color = <LED_COLOR_ID_GREEN>;
+                };
+                led-2 {
+                    rohm,led-compatible = "bd71828-ambled";
+                    function = LED_FUNCTION_CHARGING;
+                    color = <LED_COLOR_ID_AMBER>;
+                };
+            };
+        };
+    };
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 03/10] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
  2020-01-20  9:12 ` [PATCH v12 01/10] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
  2020-01-20  9:13 ` [PATCH v12 02/10] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
@ 2020-01-20  9:17 ` Matti Vaittinen
  2020-01-20  9:18 ` [PATCH v12 04/10] mfd: bd718x7: Add compatible for BD71850 Matti Vaittinen
                   ` (7 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:17 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount, Stephen Boyd, Mark Brown
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

Thanks to Stephen Boyd I today learned we can use platform_device_id
to do device and module matching for MFD sub-devices!

Do device matching using the platform_device_id instead of using
explicit module_aliases to load modules and custom parent-data field
to do module loading and sub-device matching.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>

---

Mark and Stephen - Could you please ack this or tell me what to change?

 drivers/clk/clk-bd718x7.c             | 12 ++++++++-
 drivers/mfd/rohm-bd70528.c            |  3 +--
 drivers/mfd/rohm-bd718x7.c            | 39 ++++++++++++++++++++++-----
 drivers/regulator/bd718x7-regulator.c | 17 +++++++++---
 include/linux/mfd/rohm-generic.h      |  3 +--
 5 files changed, 58 insertions(+), 16 deletions(-)

diff --git a/drivers/clk/clk-bd718x7.c b/drivers/clk/clk-bd718x7.c
index 00926c587390..33699ee1bdf3 100644
--- a/drivers/clk/clk-bd718x7.c
+++ b/drivers/clk/clk-bd718x7.c
@@ -74,6 +74,7 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 		.name = "bd718xx-32k-out",
 		.ops = &bd71837_clk_ops,
 	};
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
 	c = devm_kzalloc(&pdev->dev, sizeof(*c), GFP_KERNEL);
 	if (!c)
@@ -87,7 +88,7 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "No parent clk found\n");
 		return -EINVAL;
 	}
-	switch (mfd->chip_type) {
+	switch (chip) {
 	case ROHM_CHIP_TYPE_BD71837:
 	case ROHM_CHIP_TYPE_BD71847:
 		c->reg = BD718XX_REG_OUT32K;
@@ -121,11 +122,20 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 	return rval;
 }
 
+static const struct platform_device_id bd718x7_clk_id[] = {
+	{ "bd71837-clk", ROHM_CHIP_TYPE_BD71837 },
+	{ "bd71847-clk", ROHM_CHIP_TYPE_BD71847 },
+	{ "bd70528-clk", ROHM_CHIP_TYPE_BD70528 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_clk_id);
+
 static struct platform_driver bd71837_clk = {
 	.driver = {
 		.name = "bd718xx-clk",
 	},
 	.probe = bd71837_clk_probe,
+	.id_table = bd718x7_clk_id,
 };
 
 module_platform_driver(bd71837_clk);
diff --git a/drivers/mfd/rohm-bd70528.c b/drivers/mfd/rohm-bd70528.c
index ef6786fd3b00..5c44d3b77b3e 100644
--- a/drivers/mfd/rohm-bd70528.c
+++ b/drivers/mfd/rohm-bd70528.c
@@ -48,7 +48,7 @@ static struct mfd_cell bd70528_mfd_cells[] = {
 	 * We use BD71837 driver to drive the clock block. Only differences to
 	 * BD70528 clock gate are the register address and mask.
 	 */
-	{ .name = "bd718xx-clk", },
+	{ .name = "bd70528-clk", },
 	{ .name = "bd70528-wdt", },
 	{
 		.name = "bd70528-power",
@@ -236,7 +236,6 @@ static int bd70528_i2c_probe(struct i2c_client *i2c,
 
 	dev_set_drvdata(&i2c->dev, &bd70528->chip);
 
-	bd70528->chip.chip_type = ROHM_CHIP_TYPE_BD70528;
 	bd70528->chip.regmap = devm_regmap_init_i2c(i2c, &bd70528_regmap);
 	if (IS_ERR(bd70528->chip.regmap)) {
 		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
diff --git a/drivers/mfd/rohm-bd718x7.c b/drivers/mfd/rohm-bd718x7.c
index 85e7f5133365..bb86ec829079 100644
--- a/drivers/mfd/rohm-bd718x7.c
+++ b/drivers/mfd/rohm-bd718x7.c
@@ -30,14 +30,24 @@ static struct gpio_keys_platform_data bd718xx_powerkey_data = {
 	.name = "bd718xx-pwrkey",
 };
 
-static struct mfd_cell bd718xx_mfd_cells[] = {
+static struct mfd_cell bd71837_mfd_cells[] = {
 	{
 		.name = "gpio-keys",
 		.platform_data = &bd718xx_powerkey_data,
 		.pdata_size = sizeof(bd718xx_powerkey_data),
 	},
-	{ .name = "bd718xx-clk", },
-	{ .name = "bd718xx-pmic", },
+	{ .name = "bd71837-clk", },
+	{ .name = "bd71837-pmic", },
+};
+
+static struct mfd_cell bd71847_mfd_cells[] = {
+	{
+		.name = "gpio-keys",
+		.platform_data = &bd718xx_powerkey_data,
+		.pdata_size = sizeof(bd718xx_powerkey_data),
+	},
+	{ .name = "bd71847-clk", },
+	{ .name = "bd71847-pmic", },
 };
 
 static const struct regmap_irq bd718xx_irqs[] = {
@@ -124,6 +134,9 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 {
 	struct bd718xx *bd718xx;
 	int ret;
+	unsigned int chip_type;
+	struct mfd_cell *mfd;
+	int cells;
 
 	if (!i2c->irq) {
 		dev_err(&i2c->dev, "No IRQ configured\n");
@@ -136,8 +149,21 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 		return -ENOMEM;
 
 	bd718xx->chip_irq = i2c->irq;
-	bd718xx->chip.chip_type = (unsigned int)(uintptr_t)
-				of_device_get_match_data(&i2c->dev);
+	chip_type = (unsigned int)(uintptr_t)
+		    of_device_get_match_data(&i2c->dev);
+	switch (chip_type) {
+	case ROHM_CHIP_TYPE_BD71837:
+		mfd = bd71837_mfd_cells;
+		cells = ARRAY_SIZE(bd71837_mfd_cells);
+		break;
+	case ROHM_CHIP_TYPE_BD71847:
+		mfd = bd71847_mfd_cells;
+		cells = ARRAY_SIZE(bd71847_mfd_cells);
+		break;
+	default:
+		dev_err(&i2c->dev, "Unknown device type");
+		return -EINVAL;
+	}
 	bd718xx->chip.dev = &i2c->dev;
 	dev_set_drvdata(&i2c->dev, bd718xx);
 
@@ -170,8 +196,7 @@ static int bd718xx_i2c_probe(struct i2c_client *i2c,
 	button.irq = ret;
 
 	ret = devm_mfd_add_devices(bd718xx->chip.dev, PLATFORM_DEVID_AUTO,
-				   bd718xx_mfd_cells,
-				   ARRAY_SIZE(bd718xx_mfd_cells), NULL, 0,
+				   mfd, cells, NULL, 0,
 				   regmap_irq_get_domain(bd718xx->irq_data));
 	if (ret)
 		dev_err(&i2c->dev, "Failed to create subdevices\n");
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index 13a43eee2e46..6beaf867d9cb 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -1164,6 +1164,7 @@ static int bd718xx_probe(struct platform_device *pdev)
 
 	int i, j, err;
 	bool use_snvs;
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
 	mfd = dev_get_drvdata(pdev->dev.parent);
 	if (!mfd) {
@@ -1172,8 +1173,8 @@ static int bd718xx_probe(struct platform_device *pdev)
 		goto err;
 	}
 
-	if (mfd->chip.chip_type >= ROHM_CHIP_TYPE_AMOUNT ||
-	    !pmic_regulators[mfd->chip.chip_type].r_datas) {
+	if (chip >= ROHM_CHIP_TYPE_AMOUNT || chip < 0 ||
+	    !pmic_regulators[chip].r_datas) {
 		dev_err(&pdev->dev, "Unsupported chip type\n");
 		err = -EINVAL;
 		goto err;
@@ -1215,13 +1216,13 @@ static int bd718xx_probe(struct platform_device *pdev)
 		}
 	}
 
-	for (i = 0; i < pmic_regulators[mfd->chip.chip_type].r_amount; i++) {
+	for (i = 0; i < pmic_regulators[chip].r_amount; i++) {
 
 		const struct regulator_desc *desc;
 		struct regulator_dev *rdev;
 		const struct bd718xx_regulator_data *r;
 
-		r = &pmic_regulators[mfd->chip.chip_type].r_datas[i];
+		r = &pmic_regulators[chip].r_datas[i];
 		desc = &r->desc;
 
 		config.dev = pdev->dev.parent;
@@ -1281,11 +1282,19 @@ static int bd718xx_probe(struct platform_device *pdev)
 	return err;
 }
 
+static const struct platform_device_id bd718x7_pmic_id[] = {
+	{ "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 },
+	{ "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id);
+
 static struct platform_driver bd718xx_regulator = {
 	.driver = {
 		.name = "bd718xx-pmic",
 	},
 	.probe = bd718xx_probe,
+	.id_table = bd718x7_pmic_id,
 };
 
 module_platform_driver(bd718xx_regulator);
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index bff15ac26f2c..922f88008232 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,7 +4,7 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
-enum {
+enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
 	ROHM_CHIP_TYPE_BD70528,
@@ -12,7 +12,6 @@ enum {
 };
 
 struct rohm_regmap_dev {
-	unsigned int chip_type;
 	struct device *dev;
 	struct regmap *regmap;
 };
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 04/10] mfd: bd718x7: Add compatible for BD71850
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (2 preceding siblings ...)
  2020-01-20  9:17 ` [PATCH v12 03/10] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
@ 2020-01-20  9:18 ` Matti Vaittinen
  2020-01-20  9:18 ` [PATCH v12 05/10] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
                   ` (6 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:18 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

ROHM BD71850 PMIC is almost identical to BD71847. Main difference is some
initial voltage values for regulators. The BD71850 can be handled by
BD71847 driver but adding own compatible makes it clearer for one who
creates the DT for board containing this PMIC and allows SW to be
differentiating PMICs if needed.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/rohm-bd718x7.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/mfd/rohm-bd718x7.c b/drivers/mfd/rohm-bd718x7.c
index bb86ec829079..c32c1b6c98fa 100644
--- a/drivers/mfd/rohm-bd718x7.c
+++ b/drivers/mfd/rohm-bd718x7.c
@@ -213,6 +213,10 @@ static const struct of_device_id bd718xx_of_match[] = {
 		.compatible = "rohm,bd71847",
 		.data = (void *)ROHM_CHIP_TYPE_BD71847,
 	},
+	{
+		.compatible = "rohm,bd71850",
+		.data = (void *)ROHM_CHIP_TYPE_BD71847,
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, bd718xx_of_match);
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 05/10] mfd: bd71828: Support ROHM BD71828 PMIC - core
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (3 preceding siblings ...)
  2020-01-20  9:18 ` [PATCH v12 04/10] mfd: bd718x7: Add compatible for BD71850 Matti Vaittinen
@ 2020-01-20  9:18 ` Matti Vaittinen
  2020-01-20  9:19 ` [PATCH v12 06/10] mfd: bd71828: Add power-key support Matti Vaittinen
                   ` (5 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:18 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

BD71828GW is a single-chip power management IC for battery-powered portable
devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
single-cell linear charger. Also included is a Coulomb counter, a real-time
clock (RTC), 3 GPO/regulator control pins, HALL input and a 32.768 kHz
clock gate.

Add MFD core driver providing interrupt controller facilities and i2c
access to sub device drivers.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
 drivers/mfd/Kconfig              |  15 ++
 drivers/mfd/Makefile             |   1 +
 drivers/mfd/rohm-bd71828.c       | 318 +++++++++++++++++++++++
 include/linux/mfd/rohm-bd71828.h | 425 +++++++++++++++++++++++++++++++
 include/linux/mfd/rohm-generic.h |   1 +
 5 files changed, 760 insertions(+)
 create mode 100644 drivers/mfd/rohm-bd71828.c
 create mode 100644 include/linux/mfd/rohm-bd71828.h

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 420900852166..c3c9432ef51c 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1906,6 +1906,21 @@ config MFD_ROHM_BD70528
 	  10 bits SAR ADC for battery temperature monitor and 1S battery
 	  charger.
 
+config MFD_ROHM_BD71828
+	tristate "ROHM BD71828 Power Management IC"
+	depends on I2C=y
+	depends on OF
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	select MFD_CORE
+	help
+	  Select this option to get support for the ROHM BD71828 Power
+	  Management IC. BD71828GW is a single-chip power management IC for
+	  battery-powered portable devices. The IC integrates 7 buck
+	  converters, 7 LDOs, and a 1500 mA single-cell linear charger.
+	  Also included is a Coulomb counter, a real-time clock (RTC), and
+	  a 32.768 kHz clock gate.
+
 config MFD_STM32_LPTIMER
 	tristate "Support for STM32 Low-Power Timer"
 	depends on (ARCH_STM32 && OF) || COMPILE_TEST
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index aed99f08739f..61b3093af39d 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -252,6 +252,7 @@ obj-$(CONFIG_MFD_MXS_LRADC)     += mxs-lradc.o
 obj-$(CONFIG_MFD_SC27XX_PMIC)	+= sprd-sc27xx-spi.o
 obj-$(CONFIG_RAVE_SP_CORE)	+= rave-sp.o
 obj-$(CONFIG_MFD_ROHM_BD70528)	+= rohm-bd70528.o
+obj-$(CONFIG_MFD_ROHM_BD71828)	+= rohm-bd71828.o
 obj-$(CONFIG_MFD_ROHM_BD718XX)	+= rohm-bd718x7.o
 obj-$(CONFIG_MFD_STMFX) 	+= stmfx.o
 
diff --git a/drivers/mfd/rohm-bd71828.c b/drivers/mfd/rohm-bd71828.c
new file mode 100644
index 000000000000..0ec386c9f26b
--- /dev/null
+++ b/drivers/mfd/rohm-bd71828.c
@@ -0,0 +1,318 @@
+// SPDX-License-Identifier: GPL-2.0-only
+//
+// Copyright (C) 2019 ROHM Semiconductors
+//
+// ROHM BD71828 PMIC driver
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rohm-bd71828.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+static const struct resource rtc_irqs[] = {
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC0, "bd71828-rtc-alm-0"),
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC1, "bd71828-rtc-alm-1"),
+	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC2, "bd71828-rtc-alm-2"),
+};
+
+static struct mfd_cell bd71828_mfd_cells[] = {
+	{ .name = "bd71828-pmic", },
+	{ .name = "bd71828-gpio", },
+	{ .name = "bd71828-led", .of_compatible = "rohm,bd71828-leds" },
+	/*
+	 * We use BD71837 driver to drive the clock block. Only differences to
+	 * BD70528 clock gate are the register address and mask.
+	 */
+	{ .name = "bd71828-clk", },
+	{ .name = "bd71827-power", },
+	{
+		.name = "bd71828-rtc",
+		.resources = rtc_irqs,
+		.num_resources = ARRAY_SIZE(rtc_irqs),
+	},
+};
+
+static const struct regmap_range volatile_ranges[] = {
+	{
+		.range_min = BD71828_REG_PS_CTRL_1,
+		.range_max = BD71828_REG_PS_CTRL_1,
+	}, {
+		.range_min = BD71828_REG_PS_CTRL_3,
+		.range_max = BD71828_REG_PS_CTRL_3,
+	}, {
+		.range_min = BD71828_REG_RTC_SEC,
+		.range_max = BD71828_REG_RTC_YEAR,
+	}, {
+		/*
+		 * For now make all charger registers volatile because many
+		 * needs to be and because the charger block is not that
+		 * performance critical.
+		 */
+		.range_min = BD71828_REG_CHG_STATE,
+		.range_max = BD71828_REG_CHG_FULL,
+	}, {
+		.range_min = BD71828_REG_INT_MAIN,
+		.range_max = BD71828_REG_IO_STAT,
+	},
+};
+
+static const struct regmap_access_table volatile_regs = {
+	.yes_ranges = &volatile_ranges[0],
+	.n_yes_ranges = ARRAY_SIZE(volatile_ranges),
+};
+
+static struct regmap_config bd71828_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.volatile_table = &volatile_regs,
+	.max_register = BD71828_MAX_REGISTER,
+	.cache_type = REGCACHE_RBTREE,
+};
+
+/*
+ * Mapping of main IRQ register bits to sub-IRQ register offsets so that we can
+ * access corect sub-IRQ registers based on bits that are set in main IRQ
+ * register.
+ */
+
+static unsigned int bit0_offsets[] = {11};		/* RTC IRQ */
+static unsigned int bit1_offsets[] = {10};		/* TEMP IRQ */
+static unsigned int bit2_offsets[] = {6, 7, 8, 9};	/* BAT MON IRQ */
+static unsigned int bit3_offsets[] = {5};		/* BAT IRQ */
+static unsigned int bit4_offsets[] = {4};		/* CHG IRQ */
+static unsigned int bit5_offsets[] = {3};		/* VSYS IRQ */
+static unsigned int bit6_offsets[] = {1, 2};		/* DCIN IRQ */
+static unsigned int bit7_offsets[] = {0};		/* BUCK IRQ */
+
+static struct regmap_irq_sub_irq_map bd71828_sub_irq_offsets[] = {
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit0_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit1_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit2_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit3_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit4_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit5_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit6_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit7_offsets),
+};
+
+static struct regmap_irq bd71828_irqs[] = {
+	REGMAP_IRQ_REG(BD71828_INT_BUCK1_OCP, 0, BD71828_INT_BUCK1_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK2_OCP, 0, BD71828_INT_BUCK2_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK3_OCP, 0, BD71828_INT_BUCK3_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK4_OCP, 0, BD71828_INT_BUCK4_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK5_OCP, 0, BD71828_INT_BUCK5_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK6_OCP, 0, BD71828_INT_BUCK6_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BUCK7_OCP, 0, BD71828_INT_BUCK7_OCP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_PGFAULT, 0, BD71828_INT_PGFAULT_MASK),
+	/* DCIN1 interrupts */
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_DET, 1, BD71828_INT_DCIN_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_RMV, 1, BD71828_INT_DCIN_RMV_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CLPS_OUT, 1, BD71828_INT_CLPS_OUT_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CLPS_IN, 1, BD71828_INT_CLPS_IN_MASK),
+	/* DCIN2 interrupts */
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_RES, 2,
+		       BD71828_INT_DCIN_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_DCIN_MON_DET, 2,
+		       BD71828_INT_DCIN_MON_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_LONGPUSH, 2, BD71828_INT_LONGPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_MIDPUSH, 2, BD71828_INT_MIDPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_SHORTPUSH, 2, BD71828_INT_SHORTPUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_PUSH, 2, BD71828_INT_PUSH_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_WDOG, 2, BD71828_INT_WDOG_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_SWRESET, 2, BD71828_INT_SWRESET_MASK),
+	/* Vsys */
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_RES, 3,
+		       BD71828_INT_VSYS_UV_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_UV_DET, 3,
+		       BD71828_INT_VSYS_UV_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_RES, 3,
+		       BD71828_INT_VSYS_LOW_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_LOW_DET, 3,
+		       BD71828_INT_VSYS_LOW_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_IN, 3,
+		       BD71828_INT_VSYS_HALL_IN_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_HALL_TOGGLE, 3,
+		       BD71828_INT_VSYS_HALL_TOGGLE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_RES, 3,
+		       BD71828_INT_VSYS_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_VSYS_MON_DET, 3,
+		       BD71828_INT_VSYS_MON_DET_MASK),
+	/* Charger */
+	REGMAP_IRQ_REG(BD71828_INT_CHG_DCIN_ILIM, 4,
+		       BD71828_INT_CHG_DCIN_ILIM_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_TOPOFF_TO_DONE, 4,
+		       BD71828_INT_CHG_TOPOFF_TO_DONE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TEMP, 4,
+		       BD71828_INT_CHG_WDG_TEMP_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_WDG_TIME, 4,
+		       BD71828_INT_CHG_WDG_TIME_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_RES, 4,
+		       BD71828_INT_CHG_RECHARGE_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RECHARGE_DET, 4,
+		       BD71828_INT_CHG_RECHARGE_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_RANGED_TEMP_TRANSITION, 4,
+		       BD71828_INT_CHG_RANGED_TEMP_TRANSITION_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_CHG_STATE_TRANSITION, 4,
+		       BD71828_INT_CHG_STATE_TRANSITION_MASK),
+	/* Battery */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_NORMAL, 5,
+		       BD71828_INT_BAT_TEMP_NORMAL_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_ERANGE, 5,
+		       BD71828_INT_BAT_TEMP_ERANGE_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_TEMP_WARN, 5,
+		       BD71828_INT_BAT_TEMP_WARN_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_REMOVED, 5,
+		       BD71828_INT_BAT_REMOVED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_DETECTED, 5,
+		       BD71828_INT_BAT_DETECTED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_THERM_REMOVED, 5,
+		       BD71828_INT_THERM_REMOVED_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_THERM_DETECTED, 5,
+		       BD71828_INT_THERM_DETECTED_MASK),
+	/* Battery Mon 1 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_DEAD, 6, BD71828_INT_BAT_DEAD_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_RES, 6,
+		       BD71828_INT_BAT_SHORTC_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_SHORTC_DET, 6,
+		       BD71828_INT_BAT_SHORTC_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_RES, 6,
+		       BD71828_INT_BAT_LOW_VOLT_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_LOW_VOLT_DET, 6,
+		       BD71828_INT_BAT_LOW_VOLT_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_RES, 6,
+		       BD71828_INT_BAT_OVER_VOLT_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_VOLT_DET, 6,
+		       BD71828_INT_BAT_OVER_VOLT_DET_MASK),
+	/* Battery Mon 2 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_RES, 7,
+		       BD71828_INT_BAT_MON_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_MON_DET, 7,
+		       BD71828_INT_BAT_MON_DET_MASK),
+	/* Battery Mon 3 (Coulomb counter) */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON1, 8,
+		       BD71828_INT_BAT_CC_MON1_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON2, 8,
+		       BD71828_INT_BAT_CC_MON2_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_CC_MON3, 8,
+		       BD71828_INT_BAT_CC_MON3_MASK),
+	/* Battery Mon 4 */
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_1_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_1_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_1_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_2_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_2_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_2_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_RES, 9,
+		       BD71828_INT_BAT_OVER_CURR_3_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_BAT_OVER_CURR_3_DET, 9,
+		       BD71828_INT_BAT_OVER_CURR_3_DET_MASK),
+	/* Temperature */
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_RES, 10,
+		       BD71828_INT_TEMP_BAT_LOW_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_LOW_DET, 10,
+		       BD71828_INT_TEMP_BAT_LOW_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_RES, 10,
+		       BD71828_INT_TEMP_BAT_HI_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_BAT_HI_DET, 10,
+		       BD71828_INT_TEMP_BAT_HI_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_RES, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_125_RES_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_125_DET, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_125_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_DET, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_VF_DET_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_TEMP_CHIP_OVER_VF_RES, 10,
+		       BD71828_INT_TEMP_CHIP_OVER_VF_RES_MASK),
+	/* RTC Alarm */
+	REGMAP_IRQ_REG(BD71828_INT_RTC0, 11, BD71828_INT_RTC0_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_RTC1, 11, BD71828_INT_RTC1_MASK),
+	REGMAP_IRQ_REG(BD71828_INT_RTC2, 11, BD71828_INT_RTC2_MASK),
+};
+
+static struct regmap_irq_chip bd71828_irq_chip = {
+	.name = "bd71828_irq",
+	.main_status = BD71828_REG_INT_MAIN,
+	.irqs = &bd71828_irqs[0],
+	.num_irqs = ARRAY_SIZE(bd71828_irqs),
+	.status_base = BD71828_REG_INT_BUCK,
+	.mask_base = BD71828_REG_INT_MASK_BUCK,
+	.ack_base = BD71828_REG_INT_BUCK,
+	.mask_invert = true,
+	.init_ack_masked = true,
+	.num_regs = 12,
+	.num_main_regs = 1,
+	.sub_reg_offsets = &bd71828_sub_irq_offsets[0],
+	.num_main_status_bits = 8,
+	.irq_reg_stride = 1,
+};
+
+static int bd71828_i2c_probe(struct i2c_client *i2c)
+{
+	struct rohm_regmap_dev *chip;
+	struct regmap_irq_chip_data *irq_data;
+	int ret;
+
+	if (!i2c->irq) {
+		dev_err(&i2c->dev, "No IRQ configured\n");
+		return -EINVAL;
+	}
+
+	chip = devm_kzalloc(&i2c->dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	dev_set_drvdata(&i2c->dev, chip);
+
+	chip->regmap = devm_regmap_init_i2c(i2c, &bd71828_regmap);
+	if (IS_ERR(chip->regmap)) {
+		dev_err(&i2c->dev, "Failed to initialize Regmap\n");
+		return PTR_ERR(chip->regmap);
+	}
+
+	ret = devm_regmap_add_irq_chip(&i2c->dev, chip->regmap,
+				       i2c->irq, IRQF_ONESHOT, 0,
+				       &bd71828_irq_chip, &irq_data);
+	if (ret) {
+		dev_err(&i2c->dev, "Failed to add IRQ chip\n");
+		return ret;
+	}
+
+	dev_dbg(&i2c->dev, "Registered %d IRQs for chip\n",
+		bd71828_irq_chip.num_irqs);
+
+	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
+				   bd71828_mfd_cells,
+				   ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
+				   regmap_irq_get_domain(irq_data));
+	if (ret)
+		dev_err(&i2c->dev, "Failed to create subdevices\n");
+
+	return ret;
+}
+
+static const struct of_device_id bd71828_of_match[] = {
+	{ .compatible = "rohm,bd71828", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bd71828_of_match);
+
+static struct i2c_driver bd71828_drv = {
+	.driver = {
+		.name = "rohm-bd71828",
+		.of_match_table = bd71828_of_match,
+	},
+	.probe_new = &bd71828_i2c_probe,
+};
+module_i2c_driver(bd71828_drv);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("ROHM BD71828 Power Management IC driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
new file mode 100644
index 000000000000..eb0557eb5314
--- /dev/null
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -0,0 +1,425 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2019 ROHM Semiconductors */
+
+#ifndef __LINUX_MFD_BD71828_H__
+#define __LINUX_MFD_BD71828_H__
+
+#include <linux/mfd/rohm-generic.h>
+
+/* Regulator IDs */
+enum {
+	BD71828_BUCK1,
+	BD71828_BUCK2,
+	BD71828_BUCK3,
+	BD71828_BUCK4,
+	BD71828_BUCK5,
+	BD71828_BUCK6,
+	BD71828_BUCK7,
+	BD71828_LDO1,
+	BD71828_LDO2,
+	BD71828_LDO3,
+	BD71828_LDO4,
+	BD71828_LDO5,
+	BD71828_LDO6,
+	BD71828_LDO_SNVS,
+	BD71828_REGULATOR_AMOUNT,
+};
+
+#define BD71828_BUCK1267_VOLTS		0xEF
+#define BD71828_BUCK3_VOLTS		0x10
+#define BD71828_BUCK4_VOLTS		0x20
+#define BD71828_BUCK5_VOLTS		0x10
+#define BD71828_LDO_VOLTS		0x32
+/* LDO6 is fixed 1.8V voltage */
+#define BD71828_LDO_6_VOLTAGE		1800000
+
+/* Registers and masks*/
+
+/* MODE control */
+#define BD71828_REG_PS_CTRL_1		0x04
+#define BD71828_REG_PS_CTRL_2		0x05
+#define BD71828_REG_PS_CTRL_3		0x06
+
+//#define BD71828_REG_SWRESET		0x06
+#define BD71828_MASK_RUN_LVL_CTRL	0x30
+
+/* Regulator control masks */
+
+#define BD71828_MASK_RAMP_DELAY		0x6
+
+#define BD71828_MASK_RUN_EN		0x08
+#define BD71828_MASK_SUSP_EN		0x04
+#define BD71828_MASK_IDLE_EN		0x02
+#define BD71828_MASK_LPSR_EN		0x01
+
+#define BD71828_MASK_RUN0_EN		0x01
+#define BD71828_MASK_RUN1_EN		0x02
+#define BD71828_MASK_RUN2_EN		0x04
+#define BD71828_MASK_RUN3_EN		0x08
+
+#define BD71828_MASK_DVS_BUCK1_CTRL	0x10
+#define BD71828_DVS_BUCK1_CTRL_I2C	0
+#define BD71828_DVS_BUCK1_USE_RUNLVL	0x10
+
+#define BD71828_MASK_DVS_BUCK2_CTRL	0x20
+#define BD71828_DVS_BUCK2_CTRL_I2C	0
+#define BD71828_DVS_BUCK2_USE_RUNLVL	0x20
+
+#define BD71828_MASK_DVS_BUCK6_CTRL	0x40
+#define BD71828_DVS_BUCK6_CTRL_I2C	0
+#define BD71828_DVS_BUCK6_USE_RUNLVL	0x40
+
+#define BD71828_MASK_DVS_BUCK7_CTRL	0x80
+#define BD71828_DVS_BUCK7_CTRL_I2C	0
+#define BD71828_DVS_BUCK7_USE_RUNLVL	0x80
+
+#define BD71828_MASK_BUCK1267_VOLT	0xff
+#define BD71828_MASK_BUCK3_VOLT		0x1f
+#define BD71828_MASK_BUCK4_VOLT		0x3f
+#define BD71828_MASK_BUCK5_VOLT		0x1f
+#define BD71828_MASK_LDO_VOLT		0x3f
+
+/* Regulator control regs */
+#define BD71828_REG_BUCK1_EN		0x08
+#define BD71828_REG_BUCK1_CTRL		0x09
+#define BD71828_REG_BUCK1_MODE		0x0a
+#define BD71828_REG_BUCK1_IDLE_VOLT	0x0b
+#define BD71828_REG_BUCK1_SUSP_VOLT	0x0c
+#define BD71828_REG_BUCK1_VOLT		0x0d
+
+#define BD71828_REG_BUCK2_EN		0x12
+#define BD71828_REG_BUCK2_CTRL		0x13
+#define BD71828_REG_BUCK2_MODE		0x14
+#define BD71828_REG_BUCK2_IDLE_VOLT	0x15
+#define BD71828_REG_BUCK2_SUSP_VOLT	0x16
+#define BD71828_REG_BUCK2_VOLT		0x17
+
+#define BD71828_REG_BUCK3_EN		0x1c
+#define BD71828_REG_BUCK3_MODE		0x1d
+#define BD71828_REG_BUCK3_VOLT		0x1e
+
+#define BD71828_REG_BUCK4_EN		0x1f
+#define BD71828_REG_BUCK4_MODE		0x20
+#define BD71828_REG_BUCK4_VOLT		0x21
+
+#define BD71828_REG_BUCK5_EN		0x22
+#define BD71828_REG_BUCK5_MODE		0x23
+#define BD71828_REG_BUCK5_VOLT		0x24
+
+#define BD71828_REG_BUCK6_EN		0x25
+#define BD71828_REG_BUCK6_CTRL		0x26
+#define BD71828_REG_BUCK6_MODE		0x27
+#define BD71828_REG_BUCK6_IDLE_VOLT	0x28
+#define BD71828_REG_BUCK6_SUSP_VOLT	0x29
+#define BD71828_REG_BUCK6_VOLT		0x2a
+
+#define BD71828_REG_BUCK7_EN		0x2f
+#define BD71828_REG_BUCK7_CTRL		0x30
+#define BD71828_REG_BUCK7_MODE		0x31
+#define BD71828_REG_BUCK7_IDLE_VOLT	0x32
+#define BD71828_REG_BUCK7_SUSP_VOLT	0x33
+#define BD71828_REG_BUCK7_VOLT		0x34
+
+#define BD71828_REG_LDO1_EN		0x39
+#define BD71828_REG_LDO1_VOLT		0x3a
+#define BD71828_REG_LDO2_EN		0x3b
+#define BD71828_REG_LDO2_VOLT		0x3c
+#define BD71828_REG_LDO3_EN		0x3d
+#define BD71828_REG_LDO3_VOLT		0x3e
+#define BD71828_REG_LDO4_EN		0x3f
+#define BD71828_REG_LDO4_VOLT		0x40
+#define BD71828_REG_LDO5_EN		0x41
+#define BD71828_REG_LDO5_VOLT		0x43
+#define BD71828_REG_LDO5_VOLT_OPT	0x42
+#define BD71828_REG_LDO6_EN		0x44
+//#define BD71828_REG_LDO6_VOLT		0x4
+#define BD71828_REG_LDO7_EN		0x45
+#define BD71828_REG_LDO7_VOLT		0x46
+
+/* GPIO */
+
+#define BD71828_GPIO_DRIVE_MASK		0x2
+#define BD71828_GPIO_OPEN_DRAIN		0x0
+#define BD71828_GPIO_PUSH_PULL		0x2
+#define BD71828_GPIO_OUT_HI		0x1
+#define BD71828_GPIO_OUT_LO		0x0
+#define BD71828_GPIO_OUT_MASK		0x1
+
+#define BD71828_REG_GPIO_CTRL1		0x47
+#define BD71828_REG_GPIO_CTRL2		0x48
+#define BD71828_REG_GPIO_CTRL3		0x49
+#define BD71828_REG_IO_STAT		0xed
+
+/* RTC */
+#define BD71828_REG_RTC_SEC		0x4c
+#define BD71828_REG_RTC_MINUTE		0x4d
+#define BD71828_REG_RTC_HOUR		0x4e
+#define BD71828_REG_RTC_WEEK		0x4f
+#define BD71828_REG_RTC_DAY		0x50
+#define BD71828_REG_RTC_MONTH		0x51
+#define BD71828_REG_RTC_YEAR		0x52
+
+#define BD71828_REG_RTC_ALM0_SEC	0x53
+#define BD71828_REG_RTC_ALM0_MINUTE	0x54
+#define BD71828_REG_RTC_ALM0_HOUR	0x55
+#define BD71828_REG_RTC_ALM0_WEEK	0x56
+#define BD71828_REG_RTC_ALM0_DAY	0x57
+#define BD71828_REG_RTC_ALM0_MONTH	0x58
+#define BD71828_REG_RTC_ALM0_YEAR	0x59
+#define BD71828_REG_RTC_ALM0_MASK	0x61
+
+#define BD71828_REG_RTC_ALM1_SEC	0x5a
+#define BD71828_REG_RTC_ALM1_MINUTE	0x5b
+#define BD71828_REG_RTC_ALM1_HOUR	0x5c
+#define BD71828_REG_RTC_ALM1_WEEK	0x5d
+#define BD71828_REG_RTC_ALM1_DAY	0x5e
+#define BD71828_REG_RTC_ALM1_MONTH	0x5f
+#define BD71828_REG_RTC_ALM1_YEAR	0x60
+#define BD71828_REG_RTC_ALM1_MASK	0x62
+
+#define BD71828_REG_RTC_ALM2		0x63
+
+/* Charger/Battey */
+#define BD71828_REG_CHG_STATE		0x65
+#define BD71828_REG_CHG_FULL		0xd2
+
+/* CLK */
+#define BD71828_REG_OUT32K		0x4B
+
+/* LEDs */
+#define BD71828_REG_LED_CTRL		0x4A
+#define BD71828_MASK_LED_AMBER		0x80
+#define BD71828_MASK_LED_GREEN		0x40
+#define BD71828_LED_ON			0xff
+#define BD71828_LED_OFF			0x0
+
+/* IRQ registers */
+#define BD71828_REG_INT_MASK_BUCK	0xd3
+#define BD71828_REG_INT_MASK_DCIN1	0xd4
+#define BD71828_REG_INT_MASK_DCIN2	0xd5
+#define BD71828_REG_INT_MASK_VSYS	0xd6
+#define BD71828_REG_INT_MASK_CHG	0xd7
+#define BD71828_REG_INT_MASK_BAT	0xd8
+#define BD71828_REG_INT_MASK_BAT_MON1	0xd9
+#define BD71828_REG_INT_MASK_BAT_MON2	0xda
+#define BD71828_REG_INT_MASK_BAT_MON3	0xdb
+#define BD71828_REG_INT_MASK_BAT_MON4	0xdc
+#define BD71828_REG_INT_MASK_TEMP	0xdd
+#define BD71828_REG_INT_MASK_RTC	0xde
+
+
+#define BD71828_REG_INT_MAIN		0xdf
+#define BD71828_REG_INT_BUCK		0xe0
+#define BD71828_REG_INT_DCIN1		0xe1
+#define BD71828_REG_INT_DCIN2		0xe2
+#define BD71828_REG_INT_VSYS		0xe3
+#define BD71828_REG_INT_CHG		0xe4
+#define BD71828_REG_INT_BAT		0xe5
+#define BD71828_REG_INT_BAT_MON1	0xe6
+#define BD71828_REG_INT_BAT_MON2	0xe7
+#define BD71828_REG_INT_BAT_MON3	0xe8
+#define BD71828_REG_INT_BAT_MON4	0xe9
+#define BD71828_REG_INT_TEMP		0xea
+#define BD71828_REG_INT_RTC		0xeb
+#define BD71828_REG_INT_UPDATE		0xec
+
+#define BD71828_MAX_REGISTER BD71828_REG_IO_STAT
+
+/* Masks for main IRQ register bits */
+enum {
+	BD71828_INT_BUCK,
+#define BD71828_INT_BUCK_MASK BIT(BD71828_INT_BUCK)
+	BD71828_INT_DCIN,
+#define BD71828_INT_DCIN_MASK BIT(BD71828_INT_DCIN)
+	BD71828_INT_VSYS,
+#define BD71828_INT_VSYS_MASK BIT(BD71828_INT_VSYS)
+	BD71828_INT_CHG,
+#define BD71828_INT_CHG_MASK BIT(BD71828_INT_CHG)
+	BD71828_INT_BAT,
+#define BD71828_INT_BAT_MASK BIT(BD71828_INT_BAT)
+	BD71828_INT_BAT_MON,
+#define BD71828_INT_BAT_MON_MASK BIT(BD71828_INT_BAT_MON)
+	BD71828_INT_TEMP,
+#define BD71828_INT_TEMP_MASK BIT(BD71828_INT_TEMP)
+	BD71828_INT_RTC,
+#define BD71828_INT_RTC_MASK BIT(BD71828_INT_RTC)
+};
+
+/* Interrupts */
+enum {
+	/* BUCK reg interrupts */
+	BD71828_INT_BUCK1_OCP,
+	BD71828_INT_BUCK2_OCP,
+	BD71828_INT_BUCK3_OCP,
+	BD71828_INT_BUCK4_OCP,
+	BD71828_INT_BUCK5_OCP,
+	BD71828_INT_BUCK6_OCP,
+	BD71828_INT_BUCK7_OCP,
+	BD71828_INT_PGFAULT,
+	/* DCIN1 interrupts */
+	BD71828_INT_DCIN_DET,
+	BD71828_INT_DCIN_RMV,
+	BD71828_INT_CLPS_OUT,
+	BD71828_INT_CLPS_IN,
+	/* DCIN2 interrupts */
+	BD71828_INT_DCIN_MON_RES,
+	BD71828_INT_DCIN_MON_DET,
+	BD71828_INT_LONGPUSH,
+	BD71828_INT_MIDPUSH,
+	BD71828_INT_SHORTPUSH,
+	BD71828_INT_PUSH,
+	BD71828_INT_WDOG,
+	BD71828_INT_SWRESET,
+	/* Vsys */
+	BD71828_INT_VSYS_UV_RES,
+	BD71828_INT_VSYS_UV_DET,
+	BD71828_INT_VSYS_LOW_RES,
+	BD71828_INT_VSYS_LOW_DET,
+	BD71828_INT_VSYS_HALL_IN,
+	BD71828_INT_VSYS_HALL_TOGGLE,
+	BD71828_INT_VSYS_MON_RES,
+	BD71828_INT_VSYS_MON_DET,
+	/* Charger */
+	BD71828_INT_CHG_DCIN_ILIM,
+	BD71828_INT_CHG_TOPOFF_TO_DONE,
+	BD71828_INT_CHG_WDG_TEMP,
+	BD71828_INT_CHG_WDG_TIME,
+	BD71828_INT_CHG_RECHARGE_RES,
+	BD71828_INT_CHG_RECHARGE_DET,
+	BD71828_INT_CHG_RANGED_TEMP_TRANSITION,
+	BD71828_INT_CHG_STATE_TRANSITION,
+	/* Battery */
+	BD71828_INT_BAT_TEMP_NORMAL,
+	BD71828_INT_BAT_TEMP_ERANGE,
+	BD71828_INT_BAT_TEMP_WARN,
+	BD71828_INT_BAT_REMOVED,
+	BD71828_INT_BAT_DETECTED,
+	BD71828_INT_THERM_REMOVED,
+	BD71828_INT_THERM_DETECTED,
+	/* Battery Mon 1 */
+	BD71828_INT_BAT_DEAD,
+	BD71828_INT_BAT_SHORTC_RES,
+	BD71828_INT_BAT_SHORTC_DET,
+	BD71828_INT_BAT_LOW_VOLT_RES,
+	BD71828_INT_BAT_LOW_VOLT_DET,
+	BD71828_INT_BAT_OVER_VOLT_RES,
+	BD71828_INT_BAT_OVER_VOLT_DET,
+	/* Battery Mon 2 */
+	BD71828_INT_BAT_MON_RES,
+	BD71828_INT_BAT_MON_DET,
+	/* Battery Mon 3 (Coulomb counter) */
+	BD71828_INT_BAT_CC_MON1,
+	BD71828_INT_BAT_CC_MON2,
+	BD71828_INT_BAT_CC_MON3,
+	/* Battery Mon 4 */
+	BD71828_INT_BAT_OVER_CURR_1_RES,
+	BD71828_INT_BAT_OVER_CURR_1_DET,
+	BD71828_INT_BAT_OVER_CURR_2_RES,
+	BD71828_INT_BAT_OVER_CURR_2_DET,
+	BD71828_INT_BAT_OVER_CURR_3_RES,
+	BD71828_INT_BAT_OVER_CURR_3_DET,
+	/* Temperature */
+	BD71828_INT_TEMP_BAT_LOW_RES,
+	BD71828_INT_TEMP_BAT_LOW_DET,
+	BD71828_INT_TEMP_BAT_HI_RES,
+	BD71828_INT_TEMP_BAT_HI_DET,
+	BD71828_INT_TEMP_CHIP_OVER_125_RES,
+	BD71828_INT_TEMP_CHIP_OVER_125_DET,
+	BD71828_INT_TEMP_CHIP_OVER_VF_DET,
+	BD71828_INT_TEMP_CHIP_OVER_VF_RES,
+	/* RTC Alarm */
+	BD71828_INT_RTC0,
+	BD71828_INT_RTC1,
+	BD71828_INT_RTC2,
+};
+
+#define BD71828_INT_BUCK1_OCP_MASK			0x1
+#define BD71828_INT_BUCK2_OCP_MASK			0x2
+#define BD71828_INT_BUCK3_OCP_MASK			0x4
+#define BD71828_INT_BUCK4_OCP_MASK			0x8
+#define BD71828_INT_BUCK5_OCP_MASK			0x10
+#define BD71828_INT_BUCK6_OCP_MASK			0x20
+#define BD71828_INT_BUCK7_OCP_MASK			0x40
+#define BD71828_INT_PGFAULT_MASK			0x80
+
+#define BD71828_INT_DCIN_DET_MASK			0x1
+#define BD71828_INT_DCIN_RMV_MASK			0x2
+#define BD71828_INT_CLPS_OUT_MASK			0x4
+#define BD71828_INT_CLPS_IN_MASK			0x8
+	/* DCIN2 interrupts */
+#define BD71828_INT_DCIN_MON_RES_MASK			0x1
+#define BD71828_INT_DCIN_MON_DET_MASK			0x2
+#define BD71828_INT_LONGPUSH_MASK			0x4
+#define BD71828_INT_MIDPUSH_MASK			0x8
+#define BD71828_INT_SHORTPUSH_MASK			0x10
+#define BD71828_INT_PUSH_MASK				0x20
+#define BD71828_INT_WDOG_MASK				0x40
+#define BD71828_INT_SWRESET_MASK			0x80
+	/* Vsys */
+#define BD71828_INT_VSYS_UV_RES_MASK			0x1
+#define BD71828_INT_VSYS_UV_DET_MASK			0x2
+#define BD71828_INT_VSYS_LOW_RES_MASK			0x4
+#define BD71828_INT_VSYS_LOW_DET_MASK			0x8
+#define BD71828_INT_VSYS_HALL_IN_MASK			0x10
+#define BD71828_INT_VSYS_HALL_TOGGLE_MASK		0x20
+#define BD71828_INT_VSYS_MON_RES_MASK			0x40
+#define BD71828_INT_VSYS_MON_DET_MASK			0x80
+	/* Charger */
+#define BD71828_INT_CHG_DCIN_ILIM_MASK			0x1
+#define BD71828_INT_CHG_TOPOFF_TO_DONE_MASK		0x2
+#define BD71828_INT_CHG_WDG_TEMP_MASK			0x4
+#define BD71828_INT_CHG_WDG_TIME_MASK			0x8
+#define BD71828_INT_CHG_RECHARGE_RES_MASK		0x10
+#define BD71828_INT_CHG_RECHARGE_DET_MASK		0x20
+#define BD71828_INT_CHG_RANGED_TEMP_TRANSITION_MASK	0x40
+#define BD71828_INT_CHG_STATE_TRANSITION_MASK		0x80
+	/* Battery */
+#define BD71828_INT_BAT_TEMP_NORMAL_MASK		0x1
+#define BD71828_INT_BAT_TEMP_ERANGE_MASK		0x2
+#define BD71828_INT_BAT_TEMP_WARN_MASK			0x4
+#define BD71828_INT_BAT_REMOVED_MASK			0x10
+#define BD71828_INT_BAT_DETECTED_MASK			0x20
+#define BD71828_INT_THERM_REMOVED_MASK			0x40
+#define BD71828_INT_THERM_DETECTED_MASK			0x80
+	/* Battery Mon 1 */
+#define BD71828_INT_BAT_DEAD_MASK			0x2
+#define BD71828_INT_BAT_SHORTC_RES_MASK			0x4
+#define BD71828_INT_BAT_SHORTC_DET_MASK			0x8
+#define BD71828_INT_BAT_LOW_VOLT_RES_MASK		0x10
+#define BD71828_INT_BAT_LOW_VOLT_DET_MASK		0x20
+#define BD71828_INT_BAT_OVER_VOLT_RES_MASK		0x40
+#define BD71828_INT_BAT_OVER_VOLT_DET_MASK		0x80
+	/* Battery Mon 2 */
+#define BD71828_INT_BAT_MON_RES_MASK			0x1
+#define BD71828_INT_BAT_MON_DET_MASK			0x2
+	/* Battery Mon 3 (Coulomb counter) */
+#define BD71828_INT_BAT_CC_MON1_MASK			0x1
+#define BD71828_INT_BAT_CC_MON2_MASK			0x2
+#define BD71828_INT_BAT_CC_MON3_MASK			0x4
+	/* Battery Mon 4 */
+#define BD71828_INT_BAT_OVER_CURR_1_RES_MASK		0x1
+#define BD71828_INT_BAT_OVER_CURR_1_DET_MASK		0x2
+#define BD71828_INT_BAT_OVER_CURR_2_RES_MASK		0x4
+#define BD71828_INT_BAT_OVER_CURR_2_DET_MASK		0x8
+#define BD71828_INT_BAT_OVER_CURR_3_RES_MASK		0x10
+#define BD71828_INT_BAT_OVER_CURR_3_DET_MASK		0x20
+	/* Temperature */
+#define BD71828_INT_TEMP_BAT_LOW_RES_MASK		0x1
+#define BD71828_INT_TEMP_BAT_LOW_DET_MASK		0x2
+#define BD71828_INT_TEMP_BAT_HI_RES_MASK		0x4
+#define BD71828_INT_TEMP_BAT_HI_DET_MASK		0x8
+#define BD71828_INT_TEMP_CHIP_OVER_125_RES_MASK		0x10
+#define BD71828_INT_TEMP_CHIP_OVER_125_DET_MASK		0x20
+#define BD71828_INT_TEMP_CHIP_OVER_VF_RES_MASK		0x40
+#define BD71828_INT_TEMP_CHIP_OVER_VF_DET_MASK		0x80
+	/* RTC Alarm */
+#define BD71828_INT_RTC0_MASK				0x1
+#define BD71828_INT_RTC1_MASK				0x2
+#define BD71828_INT_RTC2_MASK				0x4
+
+#define BD71828_OUT32K_EN				0x1
+#define BD71828_OUT_TYPE_MASK				0x2
+#define BD71828_OUT_TYPE_OPEN_DRAIN			0x0
+#define BD71828_OUT_TYPE_CMOS				0x2
+
+#endif /* __LINUX_MFD_BD71828_H__ */
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index 922f88008232..ff3dd7578fd3 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -8,6 +8,7 @@ enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
 	ROHM_CHIP_TYPE_BD70528,
+	ROHM_CHIP_TYPE_BD71828,
 	ROHM_CHIP_TYPE_AMOUNT
 };
 
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 06/10] mfd: bd71828: Add power-key support
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (4 preceding siblings ...)
  2020-01-20  9:18 ` [PATCH v12 05/10] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
@ 2020-01-20  9:19 ` Matti Vaittinen
  2020-01-20  9:19 ` [PATCH v12 07/10] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
                   ` (4 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:19 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

Use gpio_keys to send power input-event to user-space when power
button (short) press is detected.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
Changes since v11:
Removed input: tag from subject

 drivers/mfd/rohm-bd71828.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/mfd/rohm-bd71828.c b/drivers/mfd/rohm-bd71828.c
index 0ec386c9f26b..210261d026f2 100644
--- a/drivers/mfd/rohm-bd71828.c
+++ b/drivers/mfd/rohm-bd71828.c
@@ -4,7 +4,9 @@
 //
 // ROHM BD71828 PMIC driver
 
+#include <linux/gpio_keys.h>
 #include <linux/i2c.h>
+#include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
 #include <linux/irq.h>
@@ -15,6 +17,18 @@
 #include <linux/regmap.h>
 #include <linux/types.h>
 
+static struct gpio_keys_button button = {
+	.code = KEY_POWER,
+	.gpio = -1,
+	.type = EV_KEY,
+};
+
+static struct gpio_keys_platform_data bd71828_powerkey_data = {
+	.buttons = &button,
+	.nbuttons = 1,
+	.name = "bd71828-pwrkey",
+};
+
 static const struct resource rtc_irqs[] = {
 	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC0, "bd71828-rtc-alm-0"),
 	DEFINE_RES_IRQ_NAMED(BD71828_INT_RTC1, "bd71828-rtc-alm-1"),
@@ -35,6 +49,10 @@ static struct mfd_cell bd71828_mfd_cells[] = {
 		.name = "bd71828-rtc",
 		.resources = rtc_irqs,
 		.num_resources = ARRAY_SIZE(rtc_irqs),
+	}, {
+		.name = "gpio-keys",
+		.platform_data = &bd71828_powerkey_data,
+		.pdata_size = sizeof(bd71828_powerkey_data),
 	},
 };
 
@@ -288,6 +306,14 @@ static int bd71828_i2c_probe(struct i2c_client *i2c)
 	dev_dbg(&i2c->dev, "Registered %d IRQs for chip\n",
 		bd71828_irq_chip.num_irqs);
 
+	ret = regmap_irq_get_virq(irq_data, BD71828_INT_SHORTPUSH);
+	if (ret < 0) {
+		dev_err(&i2c->dev, "Failed to get the power-key IRQ\n");
+		return ret;
+	}
+
+	button.irq = ret;
+
 	ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO,
 				   bd71828_mfd_cells,
 				   ARRAY_SIZE(bd71828_mfd_cells), NULL, 0,
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 07/10] clk: bd718x7: Support ROHM BD71828 clk block
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (5 preceding siblings ...)
  2020-01-20  9:19 ` [PATCH v12 06/10] mfd: bd71828: Add power-key support Matti Vaittinen
@ 2020-01-20  9:19 ` Matti Vaittinen
  2020-01-20  9:21 ` [PATCH v12 08/10] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
                   ` (3 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:19 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

BD71828GW is a single-chip power management IC for battery-powered portable
devices. Add support for controlling BD71828 clk using bd718x7 driver.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
---
 drivers/clk/Kconfig              |  6 ++---
 drivers/clk/clk-bd718x7.c        | 38 +++++++++++++++++++++++---------
 include/linux/mfd/rohm-bd70528.h |  6 -----
 include/linux/mfd/rohm-bd71828.h |  4 ----
 include/linux/mfd/rohm-bd718x7.h |  6 -----
 5 files changed, 31 insertions(+), 29 deletions(-)

diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index 45653a0e6ecd..ac5981ce2477 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -305,10 +305,10 @@ config COMMON_CLK_MMP2
 	  Support for Marvell MMP2 and MMP3 SoC clocks
 
 config COMMON_CLK_BD718XX
-	tristate "Clock driver for ROHM BD718x7 PMIC"
-	depends on MFD_ROHM_BD718XX || MFD_ROHM_BD70528
+	tristate "Clock driver for 32K clk gates on ROHM PMICs"
+	depends on MFD_ROHM_BD718XX || MFD_ROHM_BD70528 || MFD_ROHM_BD71828
 	help
-	  This driver supports ROHM BD71837, ROHM BD71847 and
+	  This driver supports ROHM BD71837, ROHM BD71847, ROHM BD71828 and
 	  ROHM BD70528 PMICs clock gates.
 
 config COMMON_CLK_FIXED_MMIO
diff --git a/drivers/clk/clk-bd718x7.c b/drivers/clk/clk-bd718x7.c
index 33699ee1bdf3..b52e8d6f660c 100644
--- a/drivers/clk/clk-bd718x7.c
+++ b/drivers/clk/clk-bd718x7.c
@@ -7,12 +7,25 @@
 #include <linux/err.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/mfd/rohm-bd718x7.h>
-#include <linux/mfd/rohm-bd70528.h>
+#include <linux/mfd/rohm-generic.h>
 #include <linux/clk-provider.h>
 #include <linux/clkdev.h>
 #include <linux/regmap.h>
 
+/* clk control registers */
+/* BD70528 */
+#define BD70528_REG_OUT32K	0x2c
+/* BD71828 */
+#define BD71828_REG_OUT32K	0x4B
+/* BD71837 and BD71847 */
+#define BD718XX_REG_OUT32K	0x2E
+
+/*
+ * BD71837, BD71847, BD70528 and BD71828 all use bit [0] to clk output control
+ */
+#define CLK_OUT_EN_MASK		BIT(0)
+
+
 struct bd718xx_clk {
 	struct clk_hw hw;
 	u8 reg;
@@ -21,10 +34,8 @@ struct bd718xx_clk {
 	struct rohm_regmap_dev *mfd;
 };
 
-static int bd71837_clk_set(struct clk_hw *hw, int status)
+static int bd71837_clk_set(struct bd718xx_clk *c, unsigned int status)
 {
-	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
-
 	return regmap_update_bits(c->mfd->regmap, c->reg, c->mask, status);
 }
 
@@ -33,14 +44,16 @@ static void bd71837_clk_disable(struct clk_hw *hw)
 	int rv;
 	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
 
-	rv = bd71837_clk_set(hw, 0);
+	rv = bd71837_clk_set(c, 0);
 	if (rv)
 		dev_dbg(&c->pdev->dev, "Failed to disable 32K clk (%d)\n", rv);
 }
 
 static int bd71837_clk_enable(struct clk_hw *hw)
 {
-	return bd71837_clk_set(hw, 1);
+	struct bd718xx_clk *c = container_of(hw, struct bd718xx_clk, hw);
+
+	return bd71837_clk_set(c, 0xffffffff);
 }
 
 static int bd71837_clk_is_enabled(struct clk_hw *hw)
@@ -92,11 +105,15 @@ static int bd71837_clk_probe(struct platform_device *pdev)
 	case ROHM_CHIP_TYPE_BD71837:
 	case ROHM_CHIP_TYPE_BD71847:
 		c->reg = BD718XX_REG_OUT32K;
-		c->mask = BD718XX_OUT32K_EN;
+		c->mask = CLK_OUT_EN_MASK;
+		break;
+	case ROHM_CHIP_TYPE_BD71828:
+		c->reg = BD71828_REG_OUT32K;
+		c->mask = CLK_OUT_EN_MASK;
 		break;
 	case ROHM_CHIP_TYPE_BD70528:
-		c->reg = BD70528_REG_CLK_OUT;
-		c->mask = BD70528_CLK_OUT_EN_MASK;
+		c->reg = BD70528_REG_OUT32K;
+		c->mask = CLK_OUT_EN_MASK;
 		break;
 	default:
 		dev_err(&pdev->dev, "Unknown clk chip\n");
@@ -126,6 +143,7 @@ static const struct platform_device_id bd718x7_clk_id[] = {
 	{ "bd71837-clk", ROHM_CHIP_TYPE_BD71837 },
 	{ "bd71847-clk", ROHM_CHIP_TYPE_BD71847 },
 	{ "bd70528-clk", ROHM_CHIP_TYPE_BD70528 },
+	{ "bd71828-clk", ROHM_CHIP_TYPE_BD71828 },
 	{ },
 };
 MODULE_DEVICE_TABLE(platform, bd718x7_clk_id);
diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index 1013e60c5b25..2ad2320d0a96 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -89,10 +89,6 @@ struct bd70528_data {
 #define BD70528_REG_GPIO3_OUT	0x52
 #define BD70528_REG_GPIO4_OUT	0x54
 
-/* clk control */
-
-#define BD70528_REG_CLK_OUT	0x2c
-
 /* RTC */
 
 #define BD70528_REG_RTC_COUNT_H		0x2d
@@ -309,8 +305,6 @@ enum {
 
 #define BD70528_GPIO_IN_STATE_BASE 1
 
-#define BD70528_CLK_OUT_EN_MASK 0x1
-
 /* RTC masks to mask out reserved bits */
 
 #define BD70528_MASK_RTC_SEC		0x7f
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index eb0557eb5314..d013e03f742d 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -183,9 +183,6 @@ enum {
 #define BD71828_REG_CHG_STATE		0x65
 #define BD71828_REG_CHG_FULL		0xd2
 
-/* CLK */
-#define BD71828_REG_OUT32K		0x4B
-
 /* LEDs */
 #define BD71828_REG_LED_CTRL		0x4A
 #define BD71828_MASK_LED_AMBER		0x80
@@ -417,7 +414,6 @@ enum {
 #define BD71828_INT_RTC1_MASK				0x2
 #define BD71828_INT_RTC2_MASK				0x4
 
-#define BD71828_OUT32K_EN				0x1
 #define BD71828_OUT_TYPE_MASK				0x2
 #define BD71828_OUT_TYPE_OPEN_DRAIN			0x0
 #define BD71828_OUT_TYPE_CMOS				0x2
diff --git a/include/linux/mfd/rohm-bd718x7.h b/include/linux/mfd/rohm-bd718x7.h
index 7f2dbde402a1..bee2474a8f9f 100644
--- a/include/linux/mfd/rohm-bd718x7.h
+++ b/include/linux/mfd/rohm-bd718x7.h
@@ -191,12 +191,6 @@ enum {
 #define IRQ_ON_REQ		0x02
 #define IRQ_STBY_REQ		0x01
 
-/* BD718XX_REG_OUT32K bits */
-#define BD718XX_OUT32K_EN	0x01
-
-/* BD7183XX gated clock rate */
-#define BD718XX_CLK_RATE 32768
-
 /* ROHM BD718XX irqs */
 enum {
 	BD718XX_INT_STBY_REQ,
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 08/10] regulator: bd718x7: Split driver to common and bd718x7 specific parts
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (6 preceding siblings ...)
  2020-01-20  9:19 ` [PATCH v12 07/10] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
@ 2020-01-20  9:21 ` Matti Vaittinen
  2020-01-20  9:21 ` [PATCH v12 09/10] mfd: bd70528: Fix hour register mask Matti Vaittinen
                   ` (2 subsequent siblings)
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:21 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

Few ROHM PMICs allow setting the voltage states for different system states
like RUN, IDLE, SUSPEND and LPSR. States are then changed via SoC specific
mechanisms. bd718x7 driver implemented device-tree parsing functions for
these state specific voltages. The parsing functions can be re-used by
other ROHM chip drivers like bd71828. Split the generic functions from
bd718x7-regulator.c to rohm-regulator.c and export them for other modules
to use.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
---
 drivers/regulator/Kconfig             |   4 +
 drivers/regulator/Makefile            |   1 +
 drivers/regulator/bd718x7-regulator.c | 183 ++++++++------------------
 drivers/regulator/rohm-regulator.c    |  95 +++++++++++++
 include/linux/mfd/rohm-generic.h      |  66 ++++++++++
 5 files changed, 221 insertions(+), 128 deletions(-)
 create mode 100644 drivers/regulator/rohm-regulator.c

diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 74eb5af7295f..a4897ae52f14 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -197,6 +197,7 @@ config REGULATOR_BD70528
 config REGULATOR_BD718XX
 	tristate "ROHM BD71837 Power Regulator"
 	depends on MFD_ROHM_BD718XX
+	select REGULATOR_ROHM
 	help
 	  This driver supports voltage regulators on ROHM BD71837 PMIC.
 	  This will enable support for the software controllable buck
@@ -790,6 +791,9 @@ config REGULATOR_RN5T618
 	  Say y here to support the regulators found on Ricoh RN5T567,
 	  RN5T618 or RC5T619 PMIC.
 
+config REGULATOR_ROHM
+	tristate
+
 config REGULATOR_RT5033
 	tristate "Richtek RT5033 Regulators"
 	depends on MFD_RT5033
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 2210ba56f9bd..6bcab72c1fc7 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -99,6 +99,7 @@ obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o
 obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
 obj-$(CONFIG_REGULATOR_RK808)   += rk808-regulator.o
 obj-$(CONFIG_REGULATOR_RN5T618) += rn5t618-regulator.o
+obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
diff --git a/drivers/regulator/bd718x7-regulator.c b/drivers/regulator/bd718x7-regulator.c
index 6beaf867d9cb..55decb58c777 100644
--- a/drivers/regulator/bd718x7-regulator.c
+++ b/drivers/regulator/bd718x7-regulator.c
@@ -318,6 +318,7 @@ struct reg_init {
 };
 struct bd718xx_regulator_data {
 	struct regulator_desc desc;
+	const struct rohm_dvs_config dvs;
 	const struct reg_init init;
 	const struct reg_init *additional_inits;
 	int additional_init_amnt;
@@ -349,133 +350,15 @@ static const struct reg_init bd71837_ldo6_inits[] = {
 	},
 };
 
-#define NUM_DVS_BUCKS 4
-
-struct of_dvs_setting {
-	const char *prop;
-	unsigned int reg;
-};
-
-static int set_dvs_levels(const struct of_dvs_setting *dvs,
-			  struct device_node *np,
-			  const struct regulator_desc *desc,
-			  struct regmap *regmap)
-{
-	int ret, i;
-	unsigned int uv;
-
-	ret = of_property_read_u32(np, dvs->prop, &uv);
-	if (ret) {
-		if (ret != -EINVAL)
-			return ret;
-		return 0;
-	}
-
-	for (i = 0; i < desc->n_voltages; i++) {
-		ret = regulator_desc_list_voltage_linear_range(desc, i);
-		if (ret < 0)
-			continue;
-		if (ret == uv) {
-			i <<= ffs(desc->vsel_mask) - 1;
-			ret = regmap_update_bits(regmap, dvs->reg,
-						 DVS_BUCK_RUN_MASK, i);
-			break;
-		}
-	}
-	return ret;
-}
-
-static int buck4_set_hw_dvs_levels(struct device_node *np,
+static int buck_set_hw_dvs_levels(struct device_node *np,
 			    const struct regulator_desc *desc,
 			    struct regulator_config *cfg)
 {
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK4_VOLT_RUN,
-		},
-	};
+	struct bd718xx_regulator_data *data;
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-static int buck3_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD71837_REG_BUCK3_VOLT_RUN,
-		},
-	};
+	data = container_of(desc, struct bd718xx_regulator_data, desc);
 
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck2_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK2_VOLT_IDLE,
-		},
-	};
-
-
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
-}
-
-static int buck1_set_hw_dvs_levels(struct device_node *np,
-			    const struct regulator_desc *desc,
-			    struct regulator_config *cfg)
-{
-	int ret, i;
-	const struct of_dvs_setting dvs[] = {
-		{
-			.prop = "rohm,dvs-run-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_RUN,
-		},
-		{
-			.prop = "rohm,dvs-idle-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_IDLE,
-		},
-		{
-			.prop = "rohm,dvs-suspend-voltage",
-			.reg = BD718XX_REG_BUCK1_VOLT_SUSP,
-		},
-	};
-
-	for (i = 0; i < ARRAY_SIZE(dvs); i++) {
-		ret = set_dvs_levels(&dvs[i], np, desc, cfg->regmap);
-		if (ret)
-			break;
-	}
-	return ret;
+	return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap);
 }
 
 static const struct bd718xx_regulator_data bd71847_regulators[] = {
@@ -496,7 +379,17 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -520,7 +413,14 @@ static const struct bd718xx_regulator_data bd71847_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -792,7 +692,17 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK1_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck1_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE |
+				     ROHM_DVS_LEVEL_SUSPEND,
+			.run_reg = BD718XX_REG_BUCK1_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
+			.suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP,
+			.suspend_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK1_CTRL,
@@ -816,7 +726,14 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD718XX_REG_BUCK2_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck2_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE,
+			.run_reg = BD718XX_REG_BUCK2_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
+			.idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE,
+			.idle_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD718XX_REG_BUCK2_CTRL,
@@ -840,7 +757,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK3_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck3_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK3_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK3_CTRL,
@@ -864,7 +786,12 @@ static const struct bd718xx_regulator_data bd71837_regulators[] = {
 			.enable_reg = BD71837_REG_BUCK4_CTRL,
 			.enable_mask = BD718XX_BUCK_EN,
 			.owner = THIS_MODULE,
-			.of_parse_cb = buck4_set_hw_dvs_levels,
+			.of_parse_cb = buck_set_hw_dvs_levels,
+		},
+		.dvs = {
+			.level_map = ROHM_DVS_LEVEL_RUN,
+			.run_reg = BD71837_REG_BUCK4_VOLT_RUN,
+			.run_mask = DVS_BUCK_RUN_MASK,
 		},
 		.init = {
 			.reg = BD71837_REG_BUCK4_CTRL,
diff --git a/drivers/regulator/rohm-regulator.c b/drivers/regulator/rohm-regulator.c
new file mode 100644
index 000000000000..399002383b28
--- /dev/null
+++ b/drivers/regulator/rohm-regulator.c
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2020 ROHM Semiconductors
+
+#include <linux/errno.h>
+#include <linux/mfd/rohm-generic.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
+static int set_dvs_level(const struct regulator_desc *desc,
+			 struct device_node *np, struct regmap *regmap,
+			 char *prop, unsigned int reg, unsigned int mask,
+			 unsigned int omask, unsigned int oreg)
+{
+	int ret, i;
+	uint32_t uv;
+
+	ret = of_property_read_u32(np, prop, &uv);
+	if (ret) {
+		if (ret != -EINVAL)
+			return ret;
+		return 0;
+	}
+
+	if (uv == 0) {
+		if (omask)
+			return regmap_update_bits(regmap, oreg, omask, 0);
+	}
+	for (i = 0; i < desc->n_voltages; i++) {
+		ret = regulator_desc_list_voltage_linear_range(desc, i);
+		if (ret < 0)
+			continue;
+		if (ret == uv) {
+			i <<= ffs(desc->vsel_mask) - 1;
+			ret = regmap_update_bits(regmap, reg, mask, i);
+			if (omask && !ret)
+				ret = regmap_update_bits(regmap, oreg, omask,
+							 omask);
+			break;
+		}
+	}
+	return ret;
+}
+
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+			  struct device_node *np,
+			  const struct regulator_desc *desc,
+			  struct regmap *regmap)
+{
+	int i, ret = 0;
+	char *prop;
+	unsigned int reg, mask, omask, oreg = desc->enable_reg;
+
+	for (i = 0; i < ROHM_DVS_LEVEL_MAX && !ret; i++) {
+		if (dvs->level_map & (1 << i)) {
+			switch (i + 1) {
+			case ROHM_DVS_LEVEL_RUN:
+				prop = "rohm,dvs-run-voltage";
+				reg = dvs->run_reg;
+				mask = dvs->run_mask;
+				omask = dvs->run_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_IDLE:
+				prop = "rohm,dvs-idle-voltage";
+				reg = dvs->idle_reg;
+				mask = dvs->idle_mask;
+				omask = dvs->idle_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_SUSPEND:
+				prop = "rohm,dvs-suspend-voltage";
+				reg = dvs->suspend_reg;
+				mask = dvs->suspend_mask;
+				omask = dvs->suspend_on_mask;
+				break;
+			case ROHM_DVS_LEVEL_LPSR:
+				prop = "rohm,dvs-lpsr-voltage";
+				reg = dvs->lpsr_reg;
+				mask = dvs->lpsr_mask;
+				omask = dvs->lpsr_on_mask;
+				break;
+			default:
+				return -EINVAL;
+			}
+			ret = set_dvs_level(desc, np, regmap, prop, reg, mask,
+					    omask, oreg);
+		}
+	}
+	return ret;
+}
+EXPORT_SYMBOL(rohm_regulator_set_dvs_levels);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("Generic helpers for ROHM PMIC regulator drivers");
diff --git a/include/linux/mfd/rohm-generic.h b/include/linux/mfd/rohm-generic.h
index ff3dd7578fd3..4283b5b33e04 100644
--- a/include/linux/mfd/rohm-generic.h
+++ b/include/linux/mfd/rohm-generic.h
@@ -4,6 +4,9 @@
 #ifndef __LINUX_MFD_ROHM_H__
 #define __LINUX_MFD_ROHM_H__
 
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+
 enum rohm_chip_type {
 	ROHM_CHIP_TYPE_BD71837 = 0,
 	ROHM_CHIP_TYPE_BD71847,
@@ -17,4 +20,67 @@ struct rohm_regmap_dev {
 	struct regmap *regmap;
 };
 
+enum {
+	ROHM_DVS_LEVEL_UNKNOWN,
+	ROHM_DVS_LEVEL_RUN,
+	ROHM_DVS_LEVEL_IDLE,
+	ROHM_DVS_LEVEL_SUSPEND,
+	ROHM_DVS_LEVEL_LPSR,
+	ROHM_DVS_LEVEL_MAX = ROHM_DVS_LEVEL_LPSR,
+};
+
+/**
+ * struct rohm_dvs_config - dynamic voltage scaling register descriptions
+ *
+ * @level_map:		bitmap representing supported run-levels for this
+ *			regulator
+ * @run_reg:		register address for regulator config at 'run' state
+ * @run_mask:		value mask for regulator voltages at 'run' state
+ * @run_on_mask:	enable mask for regulator at 'run' state
+ * @idle_reg:		register address for regulator config at 'idle' state
+ * @idle_mask:		value mask for regulator voltages at 'idle' state
+ * @idle_on_mask:	enable mask for regulator at 'idle' state
+ * @suspend_reg:	register address for regulator config at 'suspend' state
+ * @suspend_mask:	value mask for regulator voltages at 'suspend' state
+ * @suspend_on_mask:	enable mask for regulator at 'suspend' state
+ * @lpsr_reg:		register address for regulator config at 'lpsr' state
+ * @lpsr_mask:		value mask for regulator voltages at 'lpsr' state
+ * @lpsr_on_mask:	enable mask for regulator at 'lpsr' state
+ *
+ * Description of ROHM PMICs voltage configuration registers for different
+ * system states. This is used to correctly configure the PMIC at startup
+ * based on values read from DT.
+ */
+struct rohm_dvs_config {
+	uint64_t level_map;
+	unsigned int run_reg;
+	unsigned int run_mask;
+	unsigned int run_on_mask;
+	unsigned int idle_reg;
+	unsigned int idle_mask;
+	unsigned int idle_on_mask;
+	unsigned int suspend_reg;
+	unsigned int suspend_mask;
+	unsigned int suspend_on_mask;
+	unsigned int lpsr_reg;
+	unsigned int lpsr_mask;
+	unsigned int lpsr_on_mask;
+};
+
+#if IS_ENABLED(CONFIG_REGULATOR_ROHM)
+int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+				  struct device_node *np,
+				  const struct regulator_desc *desc,
+				  struct regmap *regmap);
+
+#else
+static inline int rohm_regulator_set_dvs_levels(const struct rohm_dvs_config *dvs,
+						struct device_node *np,
+						const struct regulator_desc *desc,
+						struct regmap *regmap)
+{
+	return 0;
+}
+#endif
+
 #endif
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 09/10] mfd: bd70528: Fix hour register mask
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (7 preceding siblings ...)
  2020-01-20  9:21 ` [PATCH v12 08/10] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
@ 2020-01-20  9:21 ` Matti Vaittinen
  2020-01-20  9:22 ` [PATCH v12 10/10] rtc: bd70528: add BD71828 support Matti Vaittinen
  2020-01-20 12:41 ` [PATCH v12 00/10] Support ROHM BD71828 PMIC Vaittinen, Matti
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:21 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

When RTC is used in 24H mode (and it is by this driver) the maximum
hour value is 24 in BCD. This occupies bits [5:0] - which means
correct mask for HOUR register is 0x3f not 0x1f. Fix the mask

Fixes: 32a4a4ebf768 ("rtc: bd70528: Initial support for ROHM bd70528 RTC")

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
 include/linux/mfd/rohm-bd70528.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index 2ad2320d0a96..edae6f7afd8e 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -311,7 +311,7 @@ enum {
 #define BD70528_MASK_RTC_MINUTE		0x7f
 #define BD70528_MASK_RTC_HOUR_24H	0x80
 #define BD70528_MASK_RTC_HOUR_PM	0x20
-#define BD70528_MASK_RTC_HOUR		0x1f
+#define BD70528_MASK_RTC_HOUR		0x3f
 #define BD70528_MASK_RTC_DAY		0x3f
 #define BD70528_MASK_RTC_WEEK		0x07
 #define BD70528_MASK_RTC_MONTH		0x1f
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* [PATCH v12 10/10] rtc: bd70528: add BD71828 support
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (8 preceding siblings ...)
  2020-01-20  9:21 ` [PATCH v12 09/10] mfd: bd70528: Fix hour register mask Matti Vaittinen
@ 2020-01-20  9:22 ` Matti Vaittinen
  2020-01-20 12:41 ` [PATCH v12 00/10] Support ROHM BD71828 PMIC Vaittinen, Matti
  10 siblings, 0 replies; 13+ messages in thread
From: Matti Vaittinen @ 2020-01-20  9:22 UTC (permalink / raw)
  To: matti.vaittinen, mazziesaccount
  Cc: Jacek Anaszewski, Pavel Machek, Dan Murphy, Rob Herring,
	Mark Rutland, Lee Jones, Liam Girdwood, Mark Brown,
	Jonathan Corbet, Michael Turquette, Stephen Boyd, Linus Walleij,
	Bartosz Golaszewski, Alessandro Zummo, Alexandre Belloni,
	Greg Kroah-Hartman, Arnd Bergmann, Mauro Carvalho Chehab,
	Wolfram Sang, Phil Edworthy, Noralf Trønnes, linux-leds,
	devicetree, linux-kernel, linux-doc, linux-clk, linux-gpio,
	linux-rtc

ROHM BD71828 PMIC RTC block is from many parts similar to one
on BD70528. Support BD71828 RTC using BD70528 RTC driver and
avoid re-inventing the wheel.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 drivers/rtc/Kconfig              |   3 +-
 drivers/rtc/rtc-bd70528.c        | 220 +++++++++++++++++++++++++------
 include/linux/mfd/rohm-bd70528.h |  13 +-
 include/linux/mfd/rohm-bd71828.h |   4 +-
 include/linux/mfd/rohm-shared.h  |  21 +++
 5 files changed, 206 insertions(+), 55 deletions(-)
 create mode 100644 include/linux/mfd/rohm-shared.h

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index d77515d8382c..df7a3843069d 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -498,12 +498,13 @@ config RTC_DRV_M41T80_WDT
 	help
 	  If you say Y here you will get support for the
 	  watchdog timer in the ST M41T60 and M41T80 RTC chips series.
+
 config RTC_DRV_BD70528
 	tristate "ROHM BD70528 PMIC RTC"
 	depends on MFD_ROHM_BD70528 && (BD70528_WATCHDOG || !BD70528_WATCHDOG)
 	help
 	  If you say Y here you will get support for the RTC
-	  on ROHM BD70528 Power Management IC.
+	  block on ROHM BD70528 and BD71828 Power Management IC.
 
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-bd70528.
diff --git a/drivers/rtc/rtc-bd70528.c b/drivers/rtc/rtc-bd70528.c
index 627037aa66a8..bbbb1f07c91f 100644
--- a/drivers/rtc/rtc-bd70528.c
+++ b/drivers/rtc/rtc-bd70528.c
@@ -6,6 +6,7 @@
 
 #include <linux/bcd.h>
 #include <linux/mfd/rohm-bd70528.h>
+#include <linux/mfd/rohm-bd71828.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/platform_device.h>
@@ -15,7 +16,7 @@
 /*
  * We read regs RTC_SEC => RTC_YEAR
  * this struct is ordered according to chip registers.
- * Keep it u8 only to avoid padding issues.
+ * Keep it u8 only (or packed) to avoid padding issues.
  */
 struct bd70528_rtc_day {
 	u8 sec;
@@ -36,6 +37,13 @@ struct bd70528_rtc_wake {
 	u8 ctrl;
 } __packed;
 
+struct bd71828_rtc_alm {
+	struct bd70528_rtc_data alm0;
+	struct bd70528_rtc_data alm1;
+	u8 alm_mask;
+	u8 alm1_mask;
+} __packed;
+
 struct bd70528_rtc_alm {
 	struct bd70528_rtc_data data;
 	u8 alm_mask;
@@ -43,8 +51,10 @@ struct bd70528_rtc_alm {
 } __packed;
 
 struct bd70528_rtc {
-	struct rohm_regmap_dev *mfd;
+	struct rohm_regmap_dev *parent;
 	struct device *dev;
+	u8 reg_time_start;
+	bool has_rtc_timers;
 };
 
 static int bd70528_set_wake(struct rohm_regmap_dev *bd70528,
@@ -123,14 +133,14 @@ static int bd70528_set_rtc_based_timers(struct bd70528_rtc *r, int new_state,
 {
 	int ret;
 
-	ret = bd70528_wdt_set(r->mfd, new_state & BD70528_WDT_STATE_BIT,
+	ret = bd70528_wdt_set(r->parent, new_state & BD70528_WDT_STATE_BIT,
 			      old_state);
 	if (ret) {
 		dev_err(r->dev,
 			"Failed to disable WDG for RTC setting (%d)\n", ret);
 		return ret;
 	}
-	ret = bd70528_set_elapsed_tmr(r->mfd,
+	ret = bd70528_set_elapsed_tmr(r->parent,
 				      new_state & BD70528_ELAPSED_STATE_BIT,
 				      old_state);
 	if (ret) {
@@ -138,7 +148,7 @@ static int bd70528_set_rtc_based_timers(struct bd70528_rtc *r, int new_state,
 			"Failed to disable 'elapsed timer' for RTC setting\n");
 		return ret;
 	}
-	ret = bd70528_set_wake(r->mfd, new_state & BD70528_WAKE_STATE_BIT,
+	ret = bd70528_set_wake(r->parent, new_state & BD70528_WAKE_STATE_BIT,
 			       old_state);
 	if (ret) {
 		dev_err(r->dev,
@@ -152,12 +162,18 @@ static int bd70528_set_rtc_based_timers(struct bd70528_rtc *r, int new_state,
 static int bd70528_re_enable_rtc_based_timers(struct bd70528_rtc *r,
 					      int old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, old_state, NULL);
 }
 
 static int bd70528_disable_rtc_based_timers(struct bd70528_rtc *r,
 					    int *old_state)
 {
+	if (!r->has_rtc_timers)
+		return 0;
+
 	return bd70528_set_rtc_based_timers(r, 0, old_state);
 }
 
@@ -213,22 +229,52 @@ static inline void rtc2tm(struct bd70528_rtc_data *r, struct rtc_time *t)
 	t->tm_wday = bcd2bin(r->week & BD70528_MASK_RTC_WEEK);
 }
 
+static int bd71828_set_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *parent = r->parent;
+
+	ret = regmap_bulk_read(parent->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	tm2rtc(&a->time, &alm.alm0);
+
+	if (!a->enabled)
+		alm.alm_mask &= ~BD70528_MASK_ALM_EN;
+	else
+		alm.alm_mask |= BD70528_MASK_ALM_EN;
+
+	ret = regmap_bulk_write(parent->regmap, BD71828_REG_RTC_ALM_START,
+				&alm, sizeof(alm));
+	if (ret)
+		dev_err(dev, "Failed to set alarm time\n");
+
+	return ret;
+
+}
+
 static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_wake wake;
 	struct bd70528_rtc_alm alm;
 	int ret;
 	struct bd70528_rtc *r = dev_get_drvdata(dev);
-	struct rohm_regmap_dev *bd70528 = r->mfd;
+	struct rohm_regmap_dev *parent = r->parent;
 
-	ret = regmap_bulk_read(bd70528->regmap, BD70528_REG_RTC_WAKE_START,
+	ret = regmap_bulk_read(parent->regmap, BD70528_REG_RTC_WAKE_START,
 			       &wake, sizeof(wake));
 	if (ret) {
 		dev_err(dev, "Failed to read wake regs\n");
 		return ret;
 	}
 
-	ret = regmap_bulk_read(bd70528->regmap, BD70528_REG_RTC_ALM_START,
+	ret = regmap_bulk_read(parent->regmap, BD70528_REG_RTC_ALM_START,
 			       &alm, sizeof(alm));
 	if (ret) {
 		dev_err(dev, "Failed to read alarm regs\n");
@@ -246,14 +292,14 @@ static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 		wake.ctrl &= ~BD70528_MASK_WAKE_EN;
 	}
 
-	ret = regmap_bulk_write(bd70528->regmap,
+	ret = regmap_bulk_write(parent->regmap,
 				BD70528_REG_RTC_WAKE_START, &wake,
 				sizeof(wake));
 	if (ret) {
 		dev_err(dev, "Failed to set wake time\n");
 		return ret;
 	}
-	ret = regmap_bulk_write(bd70528->regmap, BD70528_REG_RTC_ALM_START,
+	ret = regmap_bulk_write(parent->regmap, BD70528_REG_RTC_ALM_START,
 				&alm, sizeof(alm));
 	if (ret)
 		dev_err(dev, "Failed to set alarm time\n");
@@ -261,14 +307,38 @@ static int bd70528_set_alarm(struct device *dev, struct rtc_wkalrm *a)
 	return ret;
 }
 
+static int bd71828_read_alarm(struct device *dev, struct rtc_wkalrm *a)
+{
+	int ret;
+	struct bd71828_rtc_alm alm;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	struct rohm_regmap_dev *parent = r->parent;
+
+	ret = regmap_bulk_read(parent->regmap, BD71828_REG_RTC_ALM_START,
+			       &alm, sizeof(alm));
+	if (ret) {
+		dev_err(dev, "Failed to read alarm regs\n");
+		return ret;
+	}
+
+	rtc2tm(&alm.alm0, &a->time);
+	a->time.tm_mday = -1;
+	a->time.tm_mon = -1;
+	a->time.tm_year = -1;
+	a->enabled = !!(alm.alm_mask & BD70528_MASK_ALM_EN);
+	a->pending = 0;
+
+	return 0;
+}
+
 static int bd70528_read_alarm(struct device *dev, struct rtc_wkalrm *a)
 {
 	struct bd70528_rtc_alm alm;
 	int ret;
 	struct bd70528_rtc *r = dev_get_drvdata(dev);
-	struct rohm_regmap_dev *bd70528 = r->mfd;
+	struct rohm_regmap_dev *parent = r->parent;
 
-	ret = regmap_bulk_read(bd70528->regmap, BD70528_REG_RTC_ALM_START,
+	ret = regmap_bulk_read(parent->regmap, BD70528_REG_RTC_ALM_START,
 			       &alm, sizeof(alm));
 	if (ret) {
 		dev_err(dev, "Failed to read alarm regs\n");
@@ -290,14 +360,14 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	int ret, tmpret, old_states;
 	struct bd70528_rtc_data rtc_data;
 	struct bd70528_rtc *r = dev_get_drvdata(dev);
-	struct rohm_regmap_dev *bd70528 = r->mfd;
+	struct rohm_regmap_dev *parent = r->parent;
 
 	ret = bd70528_disable_rtc_based_timers(r, &old_states);
 	if (ret)
 		return ret;
 
-	tmpret = regmap_bulk_read(bd70528->regmap,
-				  BD70528_REG_RTC_START, &rtc_data,
+	tmpret = regmap_bulk_read(parent->regmap,
+				  r->reg_time_start, &rtc_data,
 				  sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to read RTC time registers\n");
@@ -305,8 +375,8 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	}
 	tm2rtc(t, &rtc_data);
 
-	tmpret = regmap_bulk_write(bd70528->regmap,
-				   BD70528_REG_RTC_START, &rtc_data,
+	tmpret = regmap_bulk_write(parent->regmap,
+				   r->reg_time_start, &rtc_data,
 				   sizeof(rtc_data));
 	if (tmpret) {
 		dev_err(dev, "Failed to set RTC time\n");
@@ -321,27 +391,32 @@ static int bd70528_set_time_locked(struct device *dev, struct rtc_time *t)
 	return ret;
 }
 
+static int bd71828_set_time(struct device *dev, struct rtc_time *t)
+{
+	return bd70528_set_time_locked(dev, t);
+}
+
 static int bd70528_set_time(struct device *dev, struct rtc_time *t)
 {
 	int ret;
 	struct bd70528_rtc *r = dev_get_drvdata(dev);
 
-	bd70528_wdt_lock(r->mfd);
+	bd70528_wdt_lock(r->parent);
 	ret = bd70528_set_time_locked(dev, t);
-	bd70528_wdt_unlock(r->mfd);
+	bd70528_wdt_unlock(r->parent);
 	return ret;
 }
 
 static int bd70528_get_time(struct device *dev, struct rtc_time *t)
 {
 	struct bd70528_rtc *r = dev_get_drvdata(dev);
-	struct rohm_regmap_dev *bd70528 = r->mfd;
+	struct rohm_regmap_dev *parent = r->parent;
 	struct bd70528_rtc_data rtc_data;
 	int ret;
 
 	/* read the RTC date and time registers all at once */
-	ret = regmap_bulk_read(bd70528->regmap,
-			       BD70528_REG_RTC_START, &rtc_data,
+	ret = regmap_bulk_read(parent->regmap,
+			       r->reg_time_start, &rtc_data,
 			       sizeof(rtc_data));
 	if (ret) {
 		dev_err(dev, "Failed to read RTC time (err %d)\n", ret);
@@ -362,19 +437,36 @@ static int bd70528_alm_enable(struct device *dev, unsigned int enabled)
 	if (enabled)
 		enableval = 0;
 
-	bd70528_wdt_lock(r->mfd);
-	ret = bd70528_set_wake(r->mfd, enabled, NULL);
+	bd70528_wdt_lock(r->parent);
+	ret = bd70528_set_wake(r->parent, enabled, NULL);
 	if (ret) {
 		dev_err(dev, "Failed to change wake state\n");
 		goto out_unlock;
 	}
-	ret = regmap_update_bits(r->mfd->regmap, BD70528_REG_RTC_ALM_MASK,
+	ret = regmap_update_bits(r->parent->regmap, BD70528_REG_RTC_ALM_MASK,
 				 BD70528_MASK_ALM_EN, enableval);
 	if (ret)
 		dev_err(dev, "Failed to change alarm state\n");
 
 out_unlock:
-	bd70528_wdt_unlock(r->mfd);
+	bd70528_wdt_unlock(r->parent);
+	return ret;
+}
+
+static int bd71828_alm_enable(struct device *dev, unsigned int enabled)
+{
+	int ret;
+	struct bd70528_rtc *r = dev_get_drvdata(dev);
+	unsigned int enableval = BD70528_MASK_ALM_EN;
+
+	if (!enabled)
+		enableval = 0;
+
+	ret = regmap_update_bits(r->parent->regmap, BD71828_REG_RTC_ALM0_MASK,
+				 BD70528_MASK_ALM_EN, enableval);
+	if (ret)
+		dev_err(dev, "Failed to change alarm state\n");
+
 	return ret;
 }
 
@@ -386,6 +478,14 @@ static const struct rtc_class_ops bd70528_rtc_ops = {
 	.alarm_irq_enable	= bd70528_alm_enable,
 };
 
+static const struct rtc_class_ops bd71828_rtc_ops = {
+	.read_time		= bd70528_get_time,
+	.set_time		= bd71828_set_time,
+	.read_alarm		= bd71828_read_alarm,
+	.set_alarm		= bd71828_set_alarm,
+	.alarm_irq_enable	= bd71828_alm_enable,
+};
+
 static irqreturn_t alm_hndlr(int irq, void *data)
 {
 	struct rtc_device *rtc = data;
@@ -397,14 +497,19 @@ static irqreturn_t alm_hndlr(int irq, void *data)
 static int bd70528_probe(struct platform_device *pdev)
 {
 	struct bd70528_rtc *bd_rtc;
-	struct rohm_regmap_dev *mfd;
+	const struct rtc_class_ops *rtc_ops;
+	struct rohm_regmap_dev *parent;
+	const char *irq_name;
 	int ret;
 	struct rtc_device *rtc;
 	int irq;
 	unsigned int hr;
+	bool enable_main_irq = false;
+	u8 hour_reg;
+	enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data;
 
-	mfd = dev_get_drvdata(pdev->dev.parent);
-	if (!mfd) {
+	parent = dev_get_drvdata(pdev->dev.parent);
+	if (!parent) {
 		dev_err(&pdev->dev, "No MFD driver data\n");
 		return -EINVAL;
 	}
@@ -412,16 +517,39 @@ static int bd70528_probe(struct platform_device *pdev)
 	if (!bd_rtc)
 		return -ENOMEM;
 
-	bd_rtc->mfd = mfd;
+	bd_rtc->parent = parent;
 	bd_rtc->dev = &pdev->dev;
 
-	irq = platform_get_irq_byname(pdev, "bd70528-rtc-alm");
-	if (irq < 0)
+	switch (chip) {
+	case ROHM_CHIP_TYPE_BD70528:
+		irq_name = "bd70528-rtc-alm";
+		bd_rtc->has_rtc_timers = true;
+		bd_rtc->reg_time_start = BD70528_REG_RTC_START;
+		hour_reg = BD70528_REG_RTC_HOUR;
+		enable_main_irq = true;
+		rtc_ops = &bd70528_rtc_ops;
+		break;
+	case ROHM_CHIP_TYPE_BD71828:
+		irq_name = "bd71828-rtc-alm-0";
+		bd_rtc->reg_time_start = BD71828_REG_RTC_START;
+		hour_reg = BD71828_REG_RTC_HOUR;
+		rtc_ops = &bd71828_rtc_ops;
+		break;
+	default:
+		dev_err(&pdev->dev, "Unknown chip\n");
+		return -ENOENT;
+	}
+
+	irq = platform_get_irq_byname(pdev, irq_name);
+
+	if (irq < 0) {
+		dev_err(&pdev->dev, "Failed to get irq\n");
 		return irq;
+	}
 
 	platform_set_drvdata(pdev, bd_rtc);
 
-	ret = regmap_read(mfd->regmap, BD70528_REG_RTC_HOUR, &hr);
+	ret = regmap_read(parent->regmap, hour_reg, &hr);
 
 	if (ret) {
 		dev_err(&pdev->dev, "Failed to reag RTC clock\n");
@@ -431,10 +559,10 @@ static int bd70528_probe(struct platform_device *pdev)
 	if (!(hr & BD70528_MASK_RTC_HOUR_24H)) {
 		struct rtc_time t;
 
-		ret = bd70528_get_time(&pdev->dev, &t);
+		ret = rtc_ops->read_time(&pdev->dev, &t);
 
 		if (!ret)
-			ret = bd70528_set_time(&pdev->dev, &t);
+			ret = rtc_ops->set_time(&pdev->dev, &t);
 
 		if (ret) {
 			dev_err(&pdev->dev,
@@ -454,7 +582,7 @@ static int bd70528_probe(struct platform_device *pdev)
 
 	rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
 	rtc->range_max = RTC_TIMESTAMP_END_2099;
-	rtc->ops = &bd70528_rtc_ops;
+	rtc->ops = rtc_ops;
 
 	/* Request alarm IRQ prior to registerig the RTC */
 	ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, &alm_hndlr,
@@ -468,27 +596,37 @@ static int bd70528_probe(struct platform_device *pdev)
 	 *  leave them enabled as irq-controller should disable irqs
 	 *  from sub-registers when IRQ is disabled or freed.
 	 */
-	ret = regmap_update_bits(mfd->regmap,
+	if (enable_main_irq) {
+		ret = regmap_update_bits(parent->regmap,
 				 BD70528_REG_INT_MAIN_MASK,
 				 BD70528_INT_RTC_MASK, 0);
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
-		return ret;
+		if (ret) {
+			dev_err(&pdev->dev, "Failed to enable RTC interrupts\n");
+			return ret;
+		}
 	}
 
 	return rtc_register_device(rtc);
 }
 
+static const struct platform_device_id bd718x7_rtc_id[] = {
+	{ "bd70528-rtc", ROHM_CHIP_TYPE_BD70528 },
+	{ "bd71828-rtc", ROHM_CHIP_TYPE_BD71828 },
+	{ },
+};
+MODULE_DEVICE_TABLE(platform, bd718x7_rtc_id);
+
 static struct platform_driver bd70528_rtc = {
 	.driver = {
 		.name = "bd70528-rtc"
 	},
 	.probe = bd70528_probe,
+	.id_table = bd718x7_rtc_id,
 };
 
 module_platform_driver(bd70528_rtc);
 
 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
-MODULE_DESCRIPTION("BD70528 RTC driver");
+MODULE_DESCRIPTION("ROHM BD70528 and BD71828 PMIC RTC driver");
 MODULE_LICENSE("GPL");
 MODULE_ALIAS("platform:bd70528-rtc");
diff --git a/include/linux/mfd/rohm-bd70528.h b/include/linux/mfd/rohm-bd70528.h
index edae6f7afd8e..a57af878fd0c 100644
--- a/include/linux/mfd/rohm-bd70528.h
+++ b/include/linux/mfd/rohm-bd70528.h
@@ -7,6 +7,7 @@
 #include <linux/bits.h>
 #include <linux/device.h>
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 #include <linux/regmap.h>
 
 enum {
@@ -307,17 +308,6 @@ enum {
 
 /* RTC masks to mask out reserved bits */
 
-#define BD70528_MASK_RTC_SEC		0x7f
-#define BD70528_MASK_RTC_MINUTE		0x7f
-#define BD70528_MASK_RTC_HOUR_24H	0x80
-#define BD70528_MASK_RTC_HOUR_PM	0x20
-#define BD70528_MASK_RTC_HOUR		0x3f
-#define BD70528_MASK_RTC_DAY		0x3f
-#define BD70528_MASK_RTC_WEEK		0x07
-#define BD70528_MASK_RTC_MONTH		0x1f
-#define BD70528_MASK_RTC_YEAR		0xff
-#define BD70528_MASK_RTC_COUNT_L	0x7f
-
 #define BD70528_MASK_ELAPSED_TIMER_EN	0x1
 /* Mask second, min and hour fields
  * HW would support ALM irq for over 24h
@@ -326,7 +316,6 @@ enum {
  * wake-up we limit ALM to 24H and only
  * unmask sec, min and hour
  */
-#define BD70528_MASK_ALM_EN		0x7
 #define BD70528_MASK_WAKE_EN		0x1
 
 /* WDT masks */
diff --git a/include/linux/mfd/rohm-bd71828.h b/include/linux/mfd/rohm-bd71828.h
index d013e03f742d..017a4c01cb31 100644
--- a/include/linux/mfd/rohm-bd71828.h
+++ b/include/linux/mfd/rohm-bd71828.h
@@ -5,6 +5,7 @@
 #define __LINUX_MFD_BD71828_H__
 
 #include <linux/mfd/rohm-generic.h>
+#include <linux/mfd/rohm-shared.h>
 
 /* Regulator IDs */
 enum {
@@ -160,6 +161,7 @@ enum {
 #define BD71828_REG_RTC_YEAR		0x52
 
 #define BD71828_REG_RTC_ALM0_SEC	0x53
+#define BD71828_REG_RTC_ALM_START	BD71828_REG_RTC_ALM0_SEC
 #define BD71828_REG_RTC_ALM0_MINUTE	0x54
 #define BD71828_REG_RTC_ALM0_HOUR	0x55
 #define BD71828_REG_RTC_ALM0_WEEK	0x56
@@ -178,6 +180,7 @@ enum {
 #define BD71828_REG_RTC_ALM1_MASK	0x62
 
 #define BD71828_REG_RTC_ALM2		0x63
+#define BD71828_REG_RTC_START		BD71828_REG_RTC_SEC
 
 /* Charger/Battey */
 #define BD71828_REG_CHG_STATE		0x65
@@ -204,7 +207,6 @@ enum {
 #define BD71828_REG_INT_MASK_TEMP	0xdd
 #define BD71828_REG_INT_MASK_RTC	0xde
 
-
 #define BD71828_REG_INT_MAIN		0xdf
 #define BD71828_REG_INT_BUCK		0xe0
 #define BD71828_REG_INT_DCIN1		0xe1
diff --git a/include/linux/mfd/rohm-shared.h b/include/linux/mfd/rohm-shared.h
new file mode 100644
index 000000000000..53dd7f638bfd
--- /dev/null
+++ b/include/linux/mfd/rohm-shared.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright (C) 2020 ROHM Semiconductors */
+
+
+#ifndef __LINUX_MFD_ROHM_SHARED_H__
+#define __LINUX_MFD_ROHM_SHARED_H__
+
+/* RTC definitions shared between BD70528 and BD71828 */
+
+#define BD70528_MASK_RTC_SEC		0x7f
+#define BD70528_MASK_RTC_MINUTE		0x7f
+#define BD70528_MASK_RTC_HOUR_24H	0x80
+#define BD70528_MASK_RTC_HOUR_PM	0x20
+#define BD70528_MASK_RTC_HOUR		0x3f
+#define BD70528_MASK_RTC_DAY		0x3f
+#define BD70528_MASK_RTC_WEEK		0x07
+#define BD70528_MASK_RTC_MONTH		0x1f
+#define BD70528_MASK_RTC_YEAR		0xff
+#define BD70528_MASK_ALM_EN		0x7
+
+#endif /* __LINUX_MFD_ROHM_SHARED_H__ */
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: [PATCH v12 00/10] Support ROHM BD71828 PMIC
  2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
                   ` (9 preceding siblings ...)
  2020-01-20  9:22 ` [PATCH v12 10/10] rtc: bd70528: add BD71828 support Matti Vaittinen
@ 2020-01-20 12:41 ` Vaittinen, Matti
  2020-01-20 13:41   ` Vaittinen, Matti
  10 siblings, 1 reply; 13+ messages in thread
From: Vaittinen, Matti @ 2020-01-20 12:41 UTC (permalink / raw)
  To: mazziesaccount
  Cc: corbet, linux-doc, phil.edworthy, dmurphy, linux-leds,
	devicetree, linux-rtc, linux-gpio, mchehab+samsung,
	alexandre.belloni, linux-kernel, mturquette, lgirdwood,
	jacek.anaszewski, wsa+renesas, a.zummo, linus.walleij, arnd,
	mark.rutland, robh+dt, noralf, gregkh, bgolaszewski, linux-clk,
	lee.jones, pavel, broonie, sboyd

Hello,

Do you know those days when nothing, _nothing_ just works out as
intended? Today is one of those.

On Mon, 2020-01-20 at 11:12 +0200, Matti Vaittinen wrote:
> Patch series introducing support for ROHM BD71828 PMIC
> 
> ROHM BD71828 is a power management IC containing 7 bucks and 7 LDOs.
> All
> regulators can be controlled individually via I2C. Bucks 1,2,6 and
> 7 can also be assigned to a "regulator group" controlled by run-
> levels.
> Eg. Run level specific voltages and enable/disable statuses for each
> of
> these bucks can be set via register interface. The buck run-level
> group
> assignment (selection if buck is to be controlled individually or via
> run-levels) can be changed at run-time via I2C.
> 
> This patch series brings only the basic support for controlling
> regulators individually via I2C.

//snip

> Patch 11:
>         Allow control of GP(I)O pins on BD71828 via GPIO subsystem
> 

I accidentally rebased to wrong commit and cropped the GPIO patch out
of the series. Lee - can you take the GPIO part from v11 (patch 11/13
there). It should apply cleanly and I have no changes to it. Or should
I just resend the whole series (again)?

Br,
    Matti Vaittinen

^ permalink raw reply	[flat|nested] 13+ messages in thread

* Re: [PATCH v12 00/10] Support ROHM BD71828 PMIC
  2020-01-20 12:41 ` [PATCH v12 00/10] Support ROHM BD71828 PMIC Vaittinen, Matti
@ 2020-01-20 13:41   ` Vaittinen, Matti
  0 siblings, 0 replies; 13+ messages in thread
From: Vaittinen, Matti @ 2020-01-20 13:41 UTC (permalink / raw)
  To: mazziesaccount
  Cc: corbet, linux-doc, phil.edworthy, dmurphy, linux-leds,
	devicetree, linux-rtc, linux-gpio, mchehab+samsung,
	alexandre.belloni, linux-kernel, mturquette, lgirdwood,
	jacek.anaszewski, wsa+renesas, a.zummo, linus.walleij, arnd,
	mark.rutland, robh+dt, noralf, gregkh, bgolaszewski, linux-clk,
	lee.jones, pavel, broonie, sboyd


On Mon, 2020-01-20 at 14:41 +0200, Matti Vaittinen wrote:
> Hello,
> 
> Do you know those days when nothing, _nothing_ just works out as
> intended? Today is one of those.
> 
> On Mon, 2020-01-20 at 11:12 +0200, Matti Vaittinen wrote:
> > Patch series introducing support for ROHM BD71828 PMIC
> > 
> > ROHM BD71828 is a power management IC containing 7 bucks and 7
> > LDOs.
> > All
> > regulators can be controlled individually via I2C. Bucks 1,2,6 and
> > 7 can also be assigned to a "regulator group" controlled by run-
> > levels.
> > Eg. Run level specific voltages and enable/disable statuses for
> > each
> > of
> > these bucks can be set via register interface. The buck run-level
> > group
> > assignment (selection if buck is to be controlled individually or
> > via
> > run-levels) can be changed at run-time via I2C.
> > 
> > This patch series brings only the basic support for controlling
> > regulators individually via I2C.
> 
> //snip
> 
> > Patch 11:
> >         Allow control of GP(I)O pins on BD71828 via GPIO subsystem
> > 
> 
> I accidentally rebased to wrong commit and cropped the GPIO patch out
> of the series. Lee - can you take the GPIO part from v11 (patch 11/13
> there). It should apply cleanly and I have no changes to it. Or
> should
> I just resend the whole series (again)?

Maybe it is clearest if I just do resend... v13 is on it's way but I
dropped most of the recipients. Please let me know if some of you want
to get it.

> 
> Br,
>     Matti Vaittinen


^ permalink raw reply	[flat|nested] 13+ messages in thread

end of thread, back to index

Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-01-20  9:12 [PATCH v12 00/10] Support ROHM BD71828 PMIC Matti Vaittinen
2020-01-20  9:12 ` [PATCH v12 01/10] dt-bindings: leds: ROHM BD71282 PMIC LED driver Matti Vaittinen
2020-01-20  9:13 ` [PATCH v12 02/10] dt-bindings: mfd: Document ROHM BD71828 bindings Matti Vaittinen
2020-01-20  9:17 ` [PATCH v12 03/10] mfd: rohm PMICs - use platform_device_id to match MFD sub-devices Matti Vaittinen
2020-01-20  9:18 ` [PATCH v12 04/10] mfd: bd718x7: Add compatible for BD71850 Matti Vaittinen
2020-01-20  9:18 ` [PATCH v12 05/10] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2020-01-20  9:19 ` [PATCH v12 06/10] mfd: bd71828: Add power-key support Matti Vaittinen
2020-01-20  9:19 ` [PATCH v12 07/10] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2020-01-20  9:21 ` [PATCH v12 08/10] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2020-01-20  9:21 ` [PATCH v12 09/10] mfd: bd70528: Fix hour register mask Matti Vaittinen
2020-01-20  9:22 ` [PATCH v12 10/10] rtc: bd70528: add BD71828 support Matti Vaittinen
2020-01-20 12:41 ` [PATCH v12 00/10] Support ROHM BD71828 PMIC Vaittinen, Matti
2020-01-20 13:41   ` Vaittinen, Matti

Linux-RTC Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-rtc/0 linux-rtc/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-rtc linux-rtc/ https://lore.kernel.org/linux-rtc \
		linux-rtc@vger.kernel.org
	public-inbox-index linux-rtc

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-rtc


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git