[PATCH AUTOSEL 4.19 14/23] scsi: bnx2fc: Return failure if io_req is already in ABTS processing

[PATCH AUTOSEL 4.19 14/23] scsi: bnx2fc: Return failure if io_req is already in ABTS processing

[Sasha Levin]

From: Javed Hasan <jhasan@marvell.com>

[ Upstream commit 122c81c563b0c1c6b15ff76a9159af5ee1f21563 ]

Return failure from bnx2fc_eh_abort() if io_req is already in ABTS
processing.

Link: https://lore.kernel.org/r/20210519061416.19321-1-jhasan@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Javed Hasan <jhasan@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/bnx2fc/bnx2fc_io.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/scsi/bnx2fc/bnx2fc_io.c b/drivers/scsi/bnx2fc/bnx2fc_io.c
index bc9f2a2365f4..5d89cc30bf30 100644
--- a/drivers/scsi/bnx2fc/bnx2fc_io.c
+++ b/drivers/scsi/bnx2fc/bnx2fc_io.c
@@ -1218,6 +1218,7 @@ int bnx2fc_eh_abort(struct scsi_cmnd *sc_cmd)
 		   was a result from the ABTS request rather than the CLEANUP
 		   request */
 		set_bit(BNX2FC_FLAG_IO_CLEANUP,	&io_req->req_flags);
+		rc = FAILED;
 		goto done;
 	}
 
-- 
2.30.2

[PATCH AUTOSEL 4.19 15/23] scsi: vmw_pvscsi: Set correct residual data length

[Sasha Levin]

From: Matt Wang <wwentao@vmware.com>

[ Upstream commit e662502b3a782d479e67736a5a1c169a703d853a ]

Some commands (such as INQUIRY) may return less data than the initiator
requested. To avoid conducting useless information, set the right residual
count to make upper layer aware of this.

Before (INQUIRY PAGE 0xB0 with 128B buffer):

$ sg_raw -r 128 /dev/sda 12 01 B0 00 80 00
SCSI Status: Good

Received 128 bytes of data:
 00 00 b0 00 3c 01 00 00 00 00 00 00 00 00 00 00 00 ...<............
 10 00 00 00 00 00 01 00 00 00 00 00 40 00 00 08 00 ...........@....
 20 80 00 00 00 00 00 00 00 00 00 20 00 00 00 00 00 .......... .....
 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
 60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

After:

$ sg_raw -r 128 /dev/sda 12 01 B0 00 80 00
SCSI Status: Good

Received 64 bytes of data:
00 00 b0 00 3c 01 00 00 00 00 00 00 00 00 00 00 00 ...<............
10 00 00 00 00 00 01 00 00 00 00 00 40 00 00 08 00 ...........@....
20 80 00 00 00 00 00 00 00 00 00 20 00 00 00 00 00 .......... .....
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

[mkp: clarified description]

Link: https://lore.kernel.org/r/03C41093-B62E-43A2-913E-CFC92F1C70C3@vmware.com
Signed-off-by: Matt Wang <wwentao@vmware.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/vmw_pvscsi.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/scsi/vmw_pvscsi.c b/drivers/scsi/vmw_pvscsi.c
index 64eb8ffb2ddf..2c707b5c7b0b 100644
--- a/drivers/scsi/vmw_pvscsi.c
+++ b/drivers/scsi/vmw_pvscsi.c
@@ -574,7 +574,13 @@ static void pvscsi_complete_request(struct pvscsi_adapter *adapter,
 		case BTSTAT_SUCCESS:
 		case BTSTAT_LINKED_COMMAND_COMPLETED:
 		case BTSTAT_LINKED_COMMAND_COMPLETED_WITH_FLAG:
-			/* If everything went fine, let's move on..  */
+			/*
+			 * Commands like INQUIRY may transfer less data than
+			 * requested by the initiator via bufflen. Set residual
+			 * count to make upper layer aware of the actual amount
+			 * of data returned.
+			 */
+			scsi_set_resid(cmd, scsi_bufflen(cmd) - e->dataLen);
 			cmd->result = (DID_OK << 16);
 			break;
 
-- 
2.30.2

[PATCH AUTOSEL 4.19 16/23] scsi: target: qla2xxx: Wait for stop_phase1 at WWN removal

[Sasha Levin]

From: Dmitry Bogdanov <d.bogdanov@yadro.com>

[ Upstream commit 2ef7665dfd88830f15415ba007c7c9a46be7acd8 ]

Target de-configuration panics at high CPU load because TPGT and WWPN can
be removed on separate threads.

TPGT removal requests a reset HBA on a separate thread and waits for reset
complete (phase1). Due to high CPU load that HBA reset can be delayed for
some time.

WWPN removal does qlt_stop_phase2(). There it is believed that phase1 has
already completed and thus tgt.tgt_ops is subsequently cleared. However,
tgt.tgt_ops is needed to process incoming traffic and therefore this will
cause one of the following panics:

NIP qlt_reset+0x7c/0x220 [qla2xxx]
LR  qlt_reset+0x68/0x220 [qla2xxx]
Call Trace:
0xc000003ffff63a78 (unreliable)
qlt_handle_imm_notify+0x800/0x10c0 [qla2xxx]
qlt_24xx_atio_pkt+0x208/0x590 [qla2xxx]
qlt_24xx_process_atio_queue+0x33c/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]

or

NIP qlt_24xx_handle_abts+0xd0/0x2a0 [qla2xxx]
LR  qlt_24xx_handle_abts+0xb4/0x2a0 [qla2xxx]
Call Trace:
qlt_24xx_handle_abts+0x90/0x2a0 [qla2xxx] (unreliable)
qlt_24xx_process_atio_queue+0x500/0x7a0 [qla2xxx]
qla83xx_msix_atio_q+0x54/0x90 [qla2xxx]

or

NIP qlt_create_sess+0x90/0x4e0 [qla2xxx]
LR  qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
Call Trace:
0xc0000000348fba30 (unreliable)
qla24xx_do_nack_work+0xa8/0x180 [qla2xxx]
qla2x00_do_work+0x674/0xbf0 [qla2xxx]
qla2x00_iocb_work_fn

The patch fixes the issue by serializing qlt_stop_phase1() and
qlt_stop_phase2() functions to make WWPN removal wait for phase1
completion.

Link: https://lore.kernel.org/r/20210415203554.27890-1-d.bogdanov@yadro.com
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/qla2xxx/qla_target.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/scsi/qla2xxx/qla_target.c b/drivers/scsi/qla2xxx/qla_target.c
index eb6112eb475e..ec54c8f34bc8 100644
--- a/drivers/scsi/qla2xxx/qla_target.c
+++ b/drivers/scsi/qla2xxx/qla_target.c
@@ -1571,10 +1571,12 @@ void qlt_stop_phase2(struct qla_tgt *tgt)
 		return;
 	}
 
+	mutex_lock(&tgt->ha->optrom_mutex);
 	mutex_lock(&vha->vha_tgt.tgt_mutex);
 	tgt->tgt_stop = 0;
 	tgt->tgt_stopped = 1;
 	mutex_unlock(&vha->vha_tgt.tgt_mutex);
+	mutex_unlock(&tgt->ha->optrom_mutex);
 
 	ql_dbg(ql_dbg_tgt_mgt, vha, 0xf00c, "Stop of tgt %p finished\n",
 	    tgt);
-- 
2.30.2