[PATCH v6 28/49] serial: ucc_uart: explicitly include soc/fsl/cpm.h

[PATCH v6 28/49] serial: ucc_uart: explicitly include soc/fsl/cpm.h

[Rasmus Villemoes]

This driver uses #defines from soc/fsl/cpm.h, so instead of relying on
some other header pulling that in, do that explicitly. This is
preparation for allowing this driver to build on ARM.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index a0555ae2b1ef..7e802616cba8 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -32,6 +32,7 @@
 #include <soc/fsl/qe/ucc_slow.h>
 
 #include <linux/firmware.h>
+#include <soc/fsl/cpm.h>
 #include <asm/reg.h>
 
 /*
-- 
2.23.0

[PATCH v6 29/49] serial: ucc_uart: replace ppc-specific IO accessors

[Rasmus Villemoes]

Some ARM-based SOCs (e.g. LS1021A) also have a QUICC engine. As
preparation for allowing this driver to build on ARM, replace the
ppc-specific in_be16() etc. by the qe_io* helpers. Done via
coccinelle.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 210 +++++++++++++++++-----------------
 1 file changed, 102 insertions(+), 108 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 7e802616cba8..8a378ee5d34f 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -258,11 +258,11 @@ static unsigned int qe_uart_tx_empty(struct uart_port *port)
 	struct qe_bd *bdp = qe_port->tx_bd_base;
 
 	while (1) {
-		if (in_be16(&bdp->status) & BD_SC_READY)
+		if (qe_ioread16be(&bdp->status) & BD_SC_READY)
 			/* This BD is not done, so return "not done" */
 			return 0;
 
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			/*
 			 * This BD is done and it's the last one, so return
 			 * "done"
@@ -308,7 +308,7 @@ static void qe_uart_stop_tx(struct uart_port *port)
 	struct uart_qe_port *qe_port =
 		container_of(port, struct uart_qe_port, port);
 
-	clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+	qe_clrbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
 }
 
 /*
@@ -343,10 +343,10 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 		p = qe2cpu_addr(bdp->buf, qe_port);
 
 		*p++ = port->x_char;
-		out_be16(&bdp->length, 1);
-		setbits16(&bdp->status, BD_SC_READY);
+		qe_iowrite16be(1, &bdp->length);
+		qe_setbits_be16(&bdp->status, BD_SC_READY);
 		/* Get next BD. */
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->tx_bd_base;
 		else
 			bdp++;
@@ -365,7 +365,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 	/* Pick next descriptor and fill from buffer */
 	bdp = qe_port->tx_cur;
 
-	while (!(in_be16(&bdp->status) & BD_SC_READY) &&
+	while (!(qe_ioread16be(&bdp->status) & BD_SC_READY) &&
 	       (xmit->tail != xmit->head)) {
 		count = 0;
 		p = qe2cpu_addr(bdp->buf, qe_port);
@@ -378,11 +378,11 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 				break;
 		}
 
-		out_be16(&bdp->length, count);
-		setbits16(&bdp->status, BD_SC_READY);
+		qe_iowrite16be(count, &bdp->length);
+		qe_setbits_be16(&bdp->status, BD_SC_READY);
 
 		/* Get next BD. */
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->tx_bd_base;
 		else
 			bdp++;
@@ -415,12 +415,12 @@ static void qe_uart_start_tx(struct uart_port *port)
 		container_of(port, struct uart_qe_port, port);
 
 	/* If we currently are transmitting, then just return */
-	if (in_be16(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
+	if (qe_ioread16be(&qe_port->uccp->uccm) & UCC_UART_UCCE_TX)
 		return;
 
 	/* Otherwise, pump the port and start transmission */
 	if (qe_uart_tx_pump(qe_port))
-		setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
+		qe_setbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_TX);
 }
 
 /*
@@ -431,7 +431,7 @@ static void qe_uart_stop_rx(struct uart_port *port)
 	struct uart_qe_port *qe_port =
 		container_of(port, struct uart_qe_port, port);
 
-	clrbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+	qe_clrbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
 }
 
 /* Start or stop sending  break signal
@@ -470,14 +470,14 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 	 */
 	bdp = qe_port->rx_cur;
 	while (1) {
-		status = in_be16(&bdp->status);
+		status = qe_ioread16be(&bdp->status);
 
 		/* If this one is empty, then we assume we've read them all */
 		if (status & BD_SC_EMPTY)
 			break;
 
 		/* get number of characters, and check space in RX buffer */
-		i = in_be16(&bdp->length);
+		i = qe_ioread16be(&bdp->length);
 
 		/* If we don't have enough room in RX buffer for the entire BD,
 		 * then we try later, which will be the next RX interrupt.
@@ -508,9 +508,10 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 		}
 
 		/* This BD is ready to be used again. Clear status. get next */
-		clrsetbits_be16(&bdp->status, BD_SC_BR | BD_SC_FR | BD_SC_PR |
-			BD_SC_OV | BD_SC_ID, BD_SC_EMPTY);
-		if (in_be16(&bdp->status) & BD_SC_WRAP)
+		qe_clrsetbits_be16(&bdp->status,
+				   BD_SC_BR | BD_SC_FR | BD_SC_PR | BD_SC_OV | BD_SC_ID,
+				   BD_SC_EMPTY);
+		if (qe_ioread16be(&bdp->status) & BD_SC_WRAP)
 			bdp = qe_port->rx_bd_base;
 		else
 			bdp++;
@@ -569,8 +570,8 @@ static irqreturn_t qe_uart_int(int irq, void *data)
 	u16 events;
 
 	/* Clear the interrupts */
-	events = in_be16(&uccp->ucce);
-	out_be16(&uccp->ucce, events);
+	events = qe_ioread16be(&uccp->ucce);
+	qe_iowrite16be(events, &uccp->ucce);
 
 	if (events & UCC_UART_UCCE_BRKE)
 		uart_handle_break(&qe_port->port);
@@ -601,17 +602,17 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port)
 	bdp = qe_port->rx_bd_base;
 	qe_port->rx_cur = qe_port->rx_bd_base;
 	for (i = 0; i < (qe_port->rx_nrfifos - 1); i++) {
-		out_be16(&bdp->status, BD_SC_EMPTY | BD_SC_INTRPT);
-		out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-		out_be16(&bdp->length, 0);
+		qe_iowrite16be(BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status);
+		qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+		qe_iowrite16be(0, &bdp->length);
 		bd_virt += qe_port->rx_fifosize;
 		bdp++;
 	}
 
 	/* */
-	out_be16(&bdp->status, BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT);
-	out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-	out_be16(&bdp->length, 0);
+	qe_iowrite16be(BD_SC_WRAP | BD_SC_EMPTY | BD_SC_INTRPT, &bdp->status);
+	qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+	qe_iowrite16be(0, &bdp->length);
 
 	/* Set the physical address of the host memory
 	 * buffers in the buffer descriptors, and the
@@ -622,21 +623,21 @@ static void qe_uart_initbd(struct uart_qe_port *qe_port)
 	qe_port->tx_cur = qe_port->tx_bd_base;
 	bdp = qe_port->tx_bd_base;
 	for (i = 0; i < (qe_port->tx_nrfifos - 1); i++) {
-		out_be16(&bdp->status, BD_SC_INTRPT);
-		out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-		out_be16(&bdp->length, 0);
+		qe_iowrite16be(BD_SC_INTRPT, &bdp->status);
+		qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+		qe_iowrite16be(0, &bdp->length);
 		bd_virt += qe_port->tx_fifosize;
 		bdp++;
 	}
 
 	/* Loopback requires the preamble bit to be set on the first TX BD */
 #ifdef LOOPBACK
-	setbits16(&qe_port->tx_cur->status, BD_SC_P);
+	qe_setbits_be16(&qe_port->tx_cur->status, BD_SC_P);
 #endif
 
-	out_be16(&bdp->status, BD_SC_WRAP | BD_SC_INTRPT);
-	out_be32(&bdp->buf, cpu2qe_addr(bd_virt, qe_port));
-	out_be16(&bdp->length, 0);
+	qe_iowrite16be(BD_SC_WRAP | BD_SC_INTRPT, &bdp->status);
+	qe_iowrite32be(cpu2qe_addr(bd_virt, qe_port), &bdp->buf);
+	qe_iowrite16be(0, &bdp->length);
 }
 
 /*
@@ -658,78 +659,74 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
 	ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
 
 	/* Program the UCC UART parameter RAM */
-	out_8(&uccup->common.rbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
-	out_8(&uccup->common.tbmr, UCC_BMR_GBL | UCC_BMR_BO_BE);
-	out_be16(&uccup->common.mrblr, qe_port->rx_fifosize);
-	out_be16(&uccup->maxidl, 0x10);
-	out_be16(&uccup->brkcr, 1);
-	out_be16(&uccup->parec, 0);
-	out_be16(&uccup->frmec, 0);
-	out_be16(&uccup->nosec, 0);
-	out_be16(&uccup->brkec, 0);
-	out_be16(&uccup->uaddr[0], 0);
-	out_be16(&uccup->uaddr[1], 0);
-	out_be16(&uccup->toseq, 0);
+	qe_iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.rbmr);
+	qe_iowrite8(UCC_BMR_GBL | UCC_BMR_BO_BE, &uccup->common.tbmr);
+	qe_iowrite16be(qe_port->rx_fifosize, &uccup->common.mrblr);
+	qe_iowrite16be(0x10, &uccup->maxidl);
+	qe_iowrite16be(1, &uccup->brkcr);
+	qe_iowrite16be(0, &uccup->parec);
+	qe_iowrite16be(0, &uccup->frmec);
+	qe_iowrite16be(0, &uccup->nosec);
+	qe_iowrite16be(0, &uccup->brkec);
+	qe_iowrite16be(0, &uccup->uaddr[0]);
+	qe_iowrite16be(0, &uccup->uaddr[1]);
+	qe_iowrite16be(0, &uccup->toseq);
 	for (i = 0; i < 8; i++)
-		out_be16(&uccup->cchars[i], 0xC000);
-	out_be16(&uccup->rccm, 0xc0ff);
+		qe_iowrite16be(0xC000, &uccup->cchars[i]);
+	qe_iowrite16be(0xc0ff, &uccup->rccm);
 
 	/* Configure the GUMR registers for UART */
 	if (soft_uart) {
 		/* Soft-UART requires a 1X multiplier for TX */
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 |
-			UCC_SLOW_GUMR_L_RDCR_16);
-
-		clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
-			UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_1 | UCC_SLOW_GUMR_L_RDCR_16);
+
+		qe_clrsetbits_be32(&uccp->gumr_h, UCC_SLOW_GUMR_H_RFW,
+				   UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX);
 	} else {
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 |
-			UCC_SLOW_GUMR_L_RDCR_16);
-
-		clrsetbits_be32(&uccp->gumr_h,
-			UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
-			UCC_SLOW_GUMR_H_RFW);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_UART | UCC_SLOW_GUMR_L_TDCR_16 | UCC_SLOW_GUMR_L_RDCR_16);
+
+		qe_clrsetbits_be32(&uccp->gumr_h,
+				   UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX,
+				   UCC_SLOW_GUMR_H_RFW);
 	}
 
 #ifdef LOOPBACK
-	clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
-		UCC_SLOW_GUMR_L_DIAG_LOOP);
-	clrsetbits_be32(&uccp->gumr_h,
-		UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
-		UCC_SLOW_GUMR_H_CDS);
+	qe_clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+			   UCC_SLOW_GUMR_L_DIAG_LOOP);
+	qe_clrsetbits_be32(&uccp->gumr_h,
+			   UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_RSYN,
+			   UCC_SLOW_GUMR_H_CDS);
 #endif
 
 	/* Disable rx interrupts  and clear all pending events.  */
-	out_be16(&uccp->uccm, 0);
-	out_be16(&uccp->ucce, 0xffff);
-	out_be16(&uccp->udsr, 0x7e7e);
+	qe_iowrite16be(0, &uccp->uccm);
+	qe_iowrite16be(0xffff, &uccp->ucce);
+	qe_iowrite16be(0x7e7e, &uccp->udsr);
 
 	/* Initialize UPSMR */
-	out_be16(&uccp->upsmr, 0);
+	qe_iowrite16be(0, &uccp->upsmr);
 
 	if (soft_uart) {
-		out_be16(&uccup->supsmr, 0x30);
-		out_be16(&uccup->res92, 0);
-		out_be32(&uccup->rx_state, 0);
-		out_be32(&uccup->rx_cnt, 0);
-		out_8(&uccup->rx_bitmark, 0);
-		out_8(&uccup->rx_length, 10);
-		out_be32(&uccup->dump_ptr, 0x4000);
-		out_8(&uccup->rx_temp_dlst_qe, 0);
-		out_be32(&uccup->rx_frame_rem, 0);
-		out_8(&uccup->rx_frame_rem_size, 0);
+		qe_iowrite16be(0x30, &uccup->supsmr);
+		qe_iowrite16be(0, &uccup->res92);
+		qe_iowrite32be(0, &uccup->rx_state);
+		qe_iowrite32be(0, &uccup->rx_cnt);
+		qe_iowrite8(0, &uccup->rx_bitmark);
+		qe_iowrite8(10, &uccup->rx_length);
+		qe_iowrite32be(0x4000, &uccup->dump_ptr);
+		qe_iowrite8(0, &uccup->rx_temp_dlst_qe);
+		qe_iowrite32be(0, &uccup->rx_frame_rem);
+		qe_iowrite8(0, &uccup->rx_frame_rem_size);
 		/* Soft-UART requires TX to be 1X */
-		out_8(&uccup->tx_mode,
-			UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1);
-		out_be16(&uccup->tx_state, 0);
-		out_8(&uccup->resD4, 0);
-		out_be16(&uccup->resD5, 0);
+		qe_iowrite8(UCC_UART_TX_STATE_UART | UCC_UART_TX_STATE_X1,
+			    &uccup->tx_mode);
+		qe_iowrite16be(0, &uccup->tx_state);
+		qe_iowrite8(0, &uccup->resD4);
+		qe_iowrite16be(0, &uccup->resD5);
 
 		/* Set UART mode.
 		 * Enable receive and transmit.
@@ -743,22 +740,19 @@ static void qe_uart_init_ucc(struct uart_qe_port *qe_port)
 		 * ...
 		 * 6.Receiver must use 16x over sampling
 		 */
-		clrsetbits_be32(&uccp->gumr_l,
-			UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK |
-			UCC_SLOW_GUMR_L_RDCR_MASK,
-			UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 |
-			UCC_SLOW_GUMR_L_RDCR_16);
+		qe_clrsetbits_be32(&uccp->gumr_l,
+				   UCC_SLOW_GUMR_L_MODE_MASK | UCC_SLOW_GUMR_L_TDCR_MASK | UCC_SLOW_GUMR_L_RDCR_MASK,
+				   UCC_SLOW_GUMR_L_MODE_QMC | UCC_SLOW_GUMR_L_TDCR_16 | UCC_SLOW_GUMR_L_RDCR_16);
 
-		clrsetbits_be32(&uccp->gumr_h,
-			UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
-			UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX |
-			UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
+		qe_clrsetbits_be32(&uccp->gumr_h,
+				   UCC_SLOW_GUMR_H_RFW | UCC_SLOW_GUMR_H_RSYN,
+				   UCC_SLOW_GUMR_H_SUART | UCC_SLOW_GUMR_H_TRX | UCC_SLOW_GUMR_H_TTX | UCC_SLOW_GUMR_H_TFL);
 
 #ifdef LOOPBACK
-		clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
-				UCC_SLOW_GUMR_L_DIAG_LOOP);
-		clrbits32(&uccp->gumr_h, UCC_SLOW_GUMR_H_CTSP |
-			  UCC_SLOW_GUMR_H_CDS);
+		qe_clrsetbits_be32(&uccp->gumr_l, UCC_SLOW_GUMR_L_DIAG_MASK,
+				   UCC_SLOW_GUMR_L_DIAG_LOOP);
+		qe_clrbits_be32(&uccp->gumr_h,
+				UCC_SLOW_GUMR_H_CTSP | UCC_SLOW_GUMR_H_CDS);
 #endif
 
 		cecr_subblock = ucc_slow_get_qe_cr_subblock(qe_port->ucc_num);
@@ -801,7 +795,7 @@ static int qe_uart_startup(struct uart_port *port)
 	}
 
 	/* Startup rx-int */
-	setbits16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
+	qe_setbits_be16(&qe_port->uccp->uccm, UCC_UART_UCCE_RX);
 	ucc_slow_enable(qe_port->us_private, COMM_DIR_RX_AND_TX);
 
 	return 0;
@@ -837,7 +831,7 @@ static void qe_uart_shutdown(struct uart_port *port)
 
 	/* Stop uarts */
 	ucc_slow_disable(qe_port->us_private, COMM_DIR_RX_AND_TX);
-	clrbits16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
+	qe_clrbits_be16(&uccp->uccm, UCC_UART_UCCE_TX | UCC_UART_UCCE_RX);
 
 	/* Shut them really down and reinit buffer descriptors */
 	ucc_slow_graceful_stop_tx(qe_port->us_private);
@@ -857,9 +851,9 @@ static void qe_uart_set_termios(struct uart_port *port,
 	struct ucc_slow __iomem *uccp = qe_port->uccp;
 	unsigned int baud;
 	unsigned long flags;
-	u16 upsmr = in_be16(&uccp->upsmr);
+	u16 upsmr = qe_ioread16be(&uccp->upsmr);
 	struct ucc_uart_pram __iomem *uccup = qe_port->uccup;
-	u16 supsmr = in_be16(&uccup->supsmr);
+	u16 supsmr = qe_ioread16be(&uccup->supsmr);
 	u8 char_length = 2; /* 1 + CL + PEN + 1 + SL */
 
 	/* Character length programmed into the mode register is the
@@ -957,10 +951,10 @@ static void qe_uart_set_termios(struct uart_port *port,
 	/* Update the per-port timeout. */
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	out_be16(&uccp->upsmr, upsmr);
+	qe_iowrite16be(upsmr, &uccp->upsmr);
 	if (soft_uart) {
-		out_be16(&uccup->supsmr, supsmr);
-		out_8(&uccup->rx_length, char_length);
+		qe_iowrite16be(supsmr, &uccup->supsmr);
+		qe_iowrite8(char_length, &uccup->rx_length);
 
 		/* Soft-UART requires a 1X multiplier for TX */
 		qe_setbrg(qe_port->us_info.rx_clock, baud, 16);
-- 
2.23.0

[PATCH v6 30/49] serial: ucc_uart: factor out soft_uart initialization

[Rasmus Villemoes]

The "soft uart" mechanism is a workaround for a silicon bug which (as
far as I know) only affects some PPC-based SOCs.

The code that determines which microcode blob to request relies on
some powerpc-specific bits (e.g. the mfspr(SPRN_SVR) and hence also
the asm/reg.h header). This makes it a little awkward to allow this
driver to be built for non-PPC based SOCs with a QE, even if they are
not affected by that silicon bug and thus don't need any of the Soft
UART logic.

There's no way around guarding those bits with some ifdeffery, so to
keep that isolated, factor out the
do-we-need-soft-uart-and-if-so-handle-the-firmware to a separate
function, which we can then easily stub out for non-PPC.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 110 ++++++++++++++++++----------------
 1 file changed, 58 insertions(+), 52 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 8a378ee5d34f..f286e91714cb 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1183,70 +1183,76 @@ static void uart_firmware_cont(const struct firmware *fw, void *context)
 	release_firmware(fw);
 }
 
-static int ucc_uart_probe(struct platform_device *ofdev)
+static int soft_uart_init(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-	const unsigned int *iprop;      /* Integer OF properties */
-	const char *sprop;      /* String OF properties */
-	struct uart_qe_port *qe_port = NULL;
-	struct resource res;
+	struct qe_firmware_info *qe_fw_info;
 	int ret;
 
-	/*
-	 * Determine if we need Soft-UART mode
-	 */
 	if (of_find_property(np, "soft-uart", NULL)) {
 		dev_dbg(&ofdev->dev, "using Soft-UART mode\n");
 		soft_uart = 1;
+	} else {
+		return 0;
 	}
 
-	/*
-	 * If we are using Soft-UART, determine if we need to upload the
-	 * firmware, too.
-	 */
-	if (soft_uart) {
-		struct qe_firmware_info *qe_fw_info;
-
-		qe_fw_info = qe_get_firmware_info();
-
-		/* Check if the firmware has been uploaded. */
-		if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
-			firmware_loaded = 1;
-		} else {
-			char filename[32];
-			unsigned int soc;
-			unsigned int rev_h;
-			unsigned int rev_l;
-
-			soc = soc_info(&rev_h, &rev_l);
-			if (!soc) {
-				dev_err(&ofdev->dev, "unknown CPU model\n");
-				return -ENXIO;
-			}
-			sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
-				soc, rev_h, rev_l);
-
-			dev_info(&ofdev->dev, "waiting for firmware %s\n",
-				filename);
+	qe_fw_info = qe_get_firmware_info();
 
-			/*
-			 * We call request_firmware_nowait instead of
-			 * request_firmware so that the driver can load and
-			 * initialize the ports without holding up the rest of
-			 * the kernel.  If hotplug support is enabled in the
-			 * kernel, then we use it.
-			 */
-			ret = request_firmware_nowait(THIS_MODULE,
-				FW_ACTION_HOTPLUG, filename, &ofdev->dev,
-				GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
-			if (ret) {
-				dev_err(&ofdev->dev,
-					"could not load firmware %s\n",
-					filename);
-				return ret;
-			}
+	/* Check if the firmware has been uploaded. */
+	if (qe_fw_info && strstr(qe_fw_info->id, "Soft-UART")) {
+		firmware_loaded = 1;
+	} else {
+		char filename[32];
+		unsigned int soc;
+		unsigned int rev_h;
+		unsigned int rev_l;
+
+		soc = soc_info(&rev_h, &rev_l);
+		if (!soc) {
+			dev_err(&ofdev->dev, "unknown CPU model\n");
+			return -ENXIO;
+		}
+		sprintf(filename, "fsl_qe_ucode_uart_%u_%u%u.bin",
+			soc, rev_h, rev_l);
+
+		dev_info(&ofdev->dev, "waiting for firmware %s\n",
+			 filename);
+
+		/*
+		 * We call request_firmware_nowait instead of
+		 * request_firmware so that the driver can load and
+		 * initialize the ports without holding up the rest of
+		 * the kernel.  If hotplug support is enabled in the
+		 * kernel, then we use it.
+		 */
+		ret = request_firmware_nowait(THIS_MODULE,
+					      FW_ACTION_HOTPLUG, filename, &ofdev->dev,
+					      GFP_KERNEL, &ofdev->dev, uart_firmware_cont);
+		if (ret) {
+			dev_err(&ofdev->dev,
+				"could not load firmware %s\n",
+				filename);
+			return ret;
 		}
 	}
+	return 0;
+}
+
+static int ucc_uart_probe(struct platform_device *ofdev)
+{
+	struct device_node *np = ofdev->dev.of_node;
+	const unsigned int *iprop;      /* Integer OF properties */
+	const char *sprop;      /* String OF properties */
+	struct uart_qe_port *qe_port = NULL;
+	struct resource res;
+	int ret;
+
+	/*
+	 * Determine if we need Soft-UART mode
+	 */
+	ret = soft_uart_init(ofdev);
+	if (ret)
+		return ret;
 
 	qe_port = kzalloc(sizeof(struct uart_qe_port), GFP_KERNEL);
 	if (!qe_port) {
-- 
2.23.0

[PATCH v6 31/49] serial: ucc_uart: stub out soft_uart_init for !CONFIG_PPC32

[Rasmus Villemoes]

The Soft UART hack is only needed for some PPC-based SOCs. To allow
building this driver for non-PPC, guard soft_uart_init() and its
helpers by CONFIG_PPC32, and use a no-op soft_uart_init() otherwise.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index f286e91714cb..313697842e24 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -33,7 +33,10 @@
 
 #include <linux/firmware.h>
 #include <soc/fsl/cpm.h>
-#include <asm/reg.h>
+
+#ifdef CONFIG_PPC32
+#include <asm/reg.h> /* mfspr, SPRN_SVR */
+#endif
 
 /*
  * The GUMR flag for Soft UART.  This would normally be defined in qe.h,
@@ -1096,6 +1099,8 @@ static const struct uart_ops qe_uart_pops = {
 	.verify_port    = qe_uart_verify_port,
 };
 
+
+#ifdef CONFIG_PPC32
 /*
  * Obtain the SOC model number and revision level
  *
@@ -1238,6 +1243,16 @@ static int soft_uart_init(struct platform_device *ofdev)
 	return 0;
 }
 
+#else /* !CONFIG_PPC32 */
+
+static int soft_uart_init(struct platform_device *ofdev)
+{
+	return 0;
+}
+
+#endif
+
+
 static int ucc_uart_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-- 
2.23.0

[PATCH v6 32/49] serial: ucc_uart: use of_property_read_u32() in ucc_uart_probe()

[Rasmus Villemoes]

For this to work correctly on little-endian hosts, don't access the
device-tree properties directly in native endianness, but use the
of_property_read_u32() helper.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 36 +++++++++++++++--------------------
 1 file changed, 15 insertions(+), 21 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 313697842e24..c055abf4c919 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1256,10 +1256,10 @@ static int soft_uart_init(struct platform_device *ofdev)
 static int ucc_uart_probe(struct platform_device *ofdev)
 {
 	struct device_node *np = ofdev->dev.of_node;
-	const unsigned int *iprop;      /* Integer OF properties */
 	const char *sprop;      /* String OF properties */
 	struct uart_qe_port *qe_port = NULL;
 	struct resource res;
+	u32 val;
 	int ret;
 
 	/*
@@ -1290,23 +1290,20 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 
 	/* Get the UCC number (device ID) */
 	/* UCCs are numbered 1-7 */
-	iprop = of_get_property(np, "cell-index", NULL);
-	if (!iprop) {
-		iprop = of_get_property(np, "device-id", NULL);
-		if (!iprop) {
-			dev_err(&ofdev->dev, "UCC is unspecified in "
-				"device tree\n");
+	if (of_property_read_u32(np, "cell-index", &val)) {
+		if (of_property_read_u32(np, "device-id", &val)) {
+			dev_err(&ofdev->dev, "UCC is unspecified in device tree\n");
 			ret = -EINVAL;
 			goto out_free;
 		}
 	}
 
-	if ((*iprop < 1) || (*iprop > UCC_MAX_NUM)) {
-		dev_err(&ofdev->dev, "no support for UCC%u\n", *iprop);
+	if (val < 1 || val > UCC_MAX_NUM) {
+		dev_err(&ofdev->dev, "no support for UCC%u\n", val);
 		ret = -ENODEV;
 		goto out_free;
 	}
-	qe_port->ucc_num = *iprop - 1;
+	qe_port->ucc_num = val - 1;
 
 	/*
 	 * In the future, we should not require the BRG to be specified in the
@@ -1350,13 +1347,12 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 	}
 
 	/* Get the port number, numbered 0-3 */
-	iprop = of_get_property(np, "port-number", NULL);
-	if (!iprop) {
+	if (of_property_read_u32(np, "port-number", &val)) {
 		dev_err(&ofdev->dev, "missing port-number in device tree\n");
 		ret = -EINVAL;
 		goto out_free;
 	}
-	qe_port->port.line = *iprop;
+	qe_port->port.line = val;
 	if (qe_port->port.line >= UCC_MAX_UART) {
 		dev_err(&ofdev->dev, "port-number must be 0-%u\n",
 			UCC_MAX_UART - 1);
@@ -1386,31 +1382,29 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 		}
 	}
 
-	iprop = of_get_property(np, "brg-frequency", NULL);
-	if (!iprop) {
+	if (of_property_read_u32(np, "brg-frequency", &val)) {
 		dev_err(&ofdev->dev,
 		       "missing brg-frequency in device tree\n");
 		ret = -EINVAL;
 		goto out_np;
 	}
 
-	if (*iprop)
-		qe_port->port.uartclk = *iprop;
+	if (val)
+		qe_port->port.uartclk = val;
 	else {
 		/*
 		 * Older versions of U-Boot do not initialize the brg-frequency
 		 * property, so in this case we assume the BRG frequency is
 		 * half the QE bus frequency.
 		 */
-		iprop = of_get_property(np, "bus-frequency", NULL);
-		if (!iprop) {
+		if (of_property_read_u32(np, "bus-frequency", &val)) {
 			dev_err(&ofdev->dev,
 				"missing QE bus-frequency in device tree\n");
 			ret = -EINVAL;
 			goto out_np;
 		}
-		if (*iprop)
-			qe_port->port.uartclk = *iprop / 2;
+		if (val)
+			qe_port->port.uartclk = val / 2;
 		else {
 			dev_err(&ofdev->dev,
 				"invalid QE bus-frequency in device tree\n");
-- 
2.23.0

[PATCH v6 33/49] serial: ucc_uart: limit brg-frequency workaround to PPC32

[Rasmus Villemoes]

According to Timur Tabi

    This bug in older U-Boots is definitely PowerPC-specific

So before allowing this driver to be built for platforms other than
PPC32, make sure that we don't accept malformed device trees on those
other platforms.

Suggested-by: Timur Tabi <timur@kernel.org>
Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index c055abf4c919..9436b93d5cfa 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -1392,6 +1392,13 @@ static int ucc_uart_probe(struct platform_device *ofdev)
 	if (val)
 		qe_port->port.uartclk = val;
 	else {
+		if (!IS_ENABLED(CONFIG_PPC32)) {
+			dev_err(&ofdev->dev,
+				"invalid brg-frequency in device tree\n");
+			ret = -EINVAL;
+			goto out_np;
+		}
+
 		/*
 		 * Older versions of U-Boot do not initialize the brg-frequency
 		 * property, so in this case we assume the BRG frequency is
-- 
2.23.0

[PATCH v6 34/49] serial: ucc_uart: access __be32 field using be32_to_cpu

[Rasmus Villemoes]

The buf member of struct qe_bd is a __be32, so to make this work on
little-endian hosts, use be32_to_cpu when reading it.

Reviewed-by: Timur Tabi <timur@kernel.org>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
---
 drivers/tty/serial/ucc_uart.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/ucc_uart.c b/drivers/tty/serial/ucc_uart.c
index 9436b93d5cfa..afc2a5d69202 100644
--- a/drivers/tty/serial/ucc_uart.c
+++ b/drivers/tty/serial/ucc_uart.c
@@ -343,7 +343,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 		/* Pick next descriptor and fill from buffer */
 		bdp = qe_port->tx_cur;
 
-		p = qe2cpu_addr(bdp->buf, qe_port);
+		p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 
 		*p++ = port->x_char;
 		qe_iowrite16be(1, &bdp->length);
@@ -371,7 +371,7 @@ static int qe_uart_tx_pump(struct uart_qe_port *qe_port)
 	while (!(qe_ioread16be(&bdp->status) & BD_SC_READY) &&
 	       (xmit->tail != xmit->head)) {
 		count = 0;
-		p = qe2cpu_addr(bdp->buf, qe_port);
+		p = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 		while (count < qe_port->tx_fifosize) {
 			*p++ = xmit->buf[xmit->tail];
 			xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
@@ -491,7 +491,7 @@ static void qe_uart_int_rx(struct uart_qe_port *qe_port)
 		}
 
 		/* get pointer */
-		cp = qe2cpu_addr(bdp->buf, qe_port);
+		cp = qe2cpu_addr(be32_to_cpu(bdp->buf), qe_port);
 
 		/* loop through the buffer */
 		while (i-- > 0) {
-- 
2.23.0