Linux-Serial Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH AUTOSEL 4.19 373/671] serial: stm32: fix word length configuration
       [not found] <20200116170509.12787-1-sashal@kernel.org>
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 374/671] serial: stm32: fix rx error handling Sasha Levin
                   ` (9 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit c8a9d043947b4acb19a65f7fac2bd0893e581cd5 ]

STM32 supports either:
- 8 and 9 bits word length (including parity bit) for stm32f4 compatible
  devices
- 7, 8 and 9 bits word length (including parity bit) for stm32f7 and
  stm32h7 compatible devices.

As a consequence STM32 supports the following termios configurations:
- CS7 with parity bit, and CS8 (with or without parity bit) for stm32f4
  compatible devices.
- CS6 with parity bit, CS7 and CS8 (with or without parity bit) for
  stm32f7 and stm32h7 compatible devices.

This patch is fixing word length by configuring correctly the SoC with
supported configurations.

Fixes: ada8618ff3bf ("serial: stm32: adding support for stm32f7")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 56 ++++++++++++++++++++++++++++----
 drivers/tty/serial/stm32-usart.h |  3 +-
 2 files changed, 50 insertions(+), 9 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index e8d7a7bb4339..e8321850938a 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -599,6 +599,36 @@ static void stm32_shutdown(struct uart_port *port)
 	free_irq(port->irq, port);
 }
 
+unsigned int stm32_get_databits(struct ktermios *termios)
+{
+	unsigned int bits;
+
+	tcflag_t cflag = termios->c_cflag;
+
+	switch (cflag & CSIZE) {
+	/*
+	 * CSIZE settings are not necessarily supported in hardware.
+	 * CSIZE unsupported configurations are handled here to set word length
+	 * to 8 bits word as default configuration and to print debug message.
+	 */
+	case CS5:
+		bits = 5;
+		break;
+	case CS6:
+		bits = 6;
+		break;
+	case CS7:
+		bits = 7;
+		break;
+	/* default including CS8 */
+	default:
+		bits = 8;
+		break;
+	}
+
+	return bits;
+}
+
 static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
 			    struct ktermios *old)
 {
@@ -606,7 +636,7 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
 	struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	struct stm32_usart_config *cfg = &stm32_port->info->cfg;
 	struct serial_rs485 *rs485conf = &port->rs485;
-	unsigned int baud;
+	unsigned int baud, bits;
 	u32 usartdiv, mantissa, fraction, oversampling;
 	tcflag_t cflag = termios->c_cflag;
 	u32 cr1, cr2, cr3;
@@ -632,16 +662,28 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
 	if (cflag & CSTOPB)
 		cr2 |= USART_CR2_STOP_2B;
 
+	bits = stm32_get_databits(termios);
+
 	if (cflag & PARENB) {
+		bits++;
 		cr1 |= USART_CR1_PCE;
-		if ((cflag & CSIZE) == CS8) {
-			if (cfg->has_7bits_data)
-				cr1 |= USART_CR1_M0;
-			else
-				cr1 |= USART_CR1_M;
-		}
 	}
 
+	/*
+	 * Word length configuration:
+	 * CS8 + parity, 9 bits word aka [M1:M0] = 0b01
+	 * CS7 or (CS6 + parity), 7 bits word aka [M1:M0] = 0b10
+	 * CS8 or (CS7 + parity), 8 bits word aka [M1:M0] = 0b00
+	 * M0 and M1 already cleared by cr1 initialization.
+	 */
+	if (bits == 9)
+		cr1 |= USART_CR1_M0;
+	else if ((bits == 7) && cfg->has_7bits_data)
+		cr1 |= USART_CR1_M1;
+	else if (bits != 8)
+		dev_dbg(port->dev, "Unsupported data bits config: %u bits\n"
+			, bits);
+
 	if (cflag & PARODD)
 		cr1 |= USART_CR1_PS;
 
diff --git a/drivers/tty/serial/stm32-usart.h b/drivers/tty/serial/stm32-usart.h
index 6f294e280ea3..a70aa5006ab9 100644
--- a/drivers/tty/serial/stm32-usart.h
+++ b/drivers/tty/serial/stm32-usart.h
@@ -151,8 +151,7 @@ struct stm32_usart_info stm32h7_info = {
 #define USART_CR1_PS		BIT(9)
 #define USART_CR1_PCE		BIT(10)
 #define USART_CR1_WAKE		BIT(11)
-#define USART_CR1_M		BIT(12)
-#define USART_CR1_M0		BIT(12)		/* F7 */
+#define USART_CR1_M0		BIT(12)		/* F7 (CR1_M for F4) */
 #define USART_CR1_MME		BIT(13)		/* F7 */
 #define USART_CR1_CMIE		BIT(14)		/* F7 */
 #define USART_CR1_OVER8		BIT(15)
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 374/671] serial: stm32: fix rx error handling
       [not found] <20200116170509.12787-1-sashal@kernel.org>
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 373/671] serial: stm32: fix word length configuration Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 375/671] serial: stm32: fix rx data length when parity enabled Sasha Levin
                   ` (8 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit 4f01d833fdcdd6f9b85d9e5d5d7568eb683626a7 ]

- Fixes parity and framing error bit by clearing parity and framing error
  flag. The current implementation doesn't clear the error bits when an
  error is detected.
- Fixes the incorrect name of framing error clearing flag in header file.
- Fixes misalignement between data frame and errors status. The status
  read for "n" frame was the status of "n+1" frame".
- Fixes break detection was not triggered by the expected register.

Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 54 +++++++++++++++++++++-----------
 drivers/tty/serial/stm32-usart.h | 10 ++----
 2 files changed, 37 insertions(+), 27 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index e8321850938a..f6b739351dde 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -225,35 +225,51 @@ static void stm32_receive_chars(struct uart_port *port, bool threaded)
 
 	while (stm32_pending_rx(port, &sr, &stm32_port->last_res, threaded)) {
 		sr |= USART_SR_DUMMY_RX;
-		c = stm32_get_char(port, &sr, &stm32_port->last_res);
 		flag = TTY_NORMAL;
-		port->icount.rx++;
 
+		/*
+		 * Status bits has to be cleared before reading the RDR:
+		 * In FIFO mode, reading the RDR will pop the next data
+		 * (if any) along with its status bits into the SR.
+		 * Not doing so leads to misalignement between RDR and SR,
+		 * and clear status bits of the next rx data.
+		 *
+		 * Clear errors flags for stm32f7 and stm32h7 compatible
+		 * devices. On stm32f4 compatible devices, the error bit is
+		 * cleared by the sequence [read SR - read DR].
+		 */
+		if ((sr & USART_SR_ERR_MASK) && ofs->icr != UNDEF_REG)
+			stm32_clr_bits(port, ofs->icr, USART_ICR_ORECF |
+				       USART_ICR_PECF | USART_ICR_FECF);
+
+		c = stm32_get_char(port, &sr, &stm32_port->last_res);
+		port->icount.rx++;
 		if (sr & USART_SR_ERR_MASK) {
-			if (sr & USART_SR_LBD) {
-				port->icount.brk++;
-				if (uart_handle_break(port))
-					continue;
-			} else if (sr & USART_SR_ORE) {
-				if (ofs->icr != UNDEF_REG)
-					writel_relaxed(USART_ICR_ORECF,
-						       port->membase +
-						       ofs->icr);
+			if (sr & USART_SR_ORE) {
 				port->icount.overrun++;
 			} else if (sr & USART_SR_PE) {
 				port->icount.parity++;
 			} else if (sr & USART_SR_FE) {
-				port->icount.frame++;
+				/* Break detection if character is null */
+				if (!c) {
+					port->icount.brk++;
+					if (uart_handle_break(port))
+						continue;
+				} else {
+					port->icount.frame++;
+				}
 			}
 
 			sr &= port->read_status_mask;
 
-			if (sr & USART_SR_LBD)
-				flag = TTY_BREAK;
-			else if (sr & USART_SR_PE)
+			if (sr & USART_SR_PE) {
 				flag = TTY_PARITY;
-			else if (sr & USART_SR_FE)
-				flag = TTY_FRAME;
+			} else if (sr & USART_SR_FE) {
+				if (!c)
+					flag = TTY_BREAK;
+				else
+					flag = TTY_FRAME;
+			}
 		}
 
 		if (uart_handle_sysrq_char(port, c))
@@ -721,14 +737,14 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
 	if (termios->c_iflag & INPCK)
 		port->read_status_mask |= USART_SR_PE | USART_SR_FE;
 	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
-		port->read_status_mask |= USART_SR_LBD;
+		port->read_status_mask |= USART_SR_FE;
 
 	/* Characters to ignore */
 	port->ignore_status_mask = 0;
 	if (termios->c_iflag & IGNPAR)
 		port->ignore_status_mask = USART_SR_PE | USART_SR_FE;
 	if (termios->c_iflag & IGNBRK) {
-		port->ignore_status_mask |= USART_SR_LBD;
+		port->ignore_status_mask |= USART_SR_FE;
 		/*
 		 * If we're ignoring parity and break indicators,
 		 * ignore overruns too (for real raw support).
diff --git a/drivers/tty/serial/stm32-usart.h b/drivers/tty/serial/stm32-usart.h
index a70aa5006ab9..8d34802e572e 100644
--- a/drivers/tty/serial/stm32-usart.h
+++ b/drivers/tty/serial/stm32-usart.h
@@ -108,7 +108,6 @@ struct stm32_usart_info stm32h7_info = {
 #define USART_SR_RXNE		BIT(5)
 #define USART_SR_TC		BIT(6)
 #define USART_SR_TXE		BIT(7)
-#define USART_SR_LBD		BIT(8)
 #define USART_SR_CTSIF		BIT(9)
 #define USART_SR_CTS		BIT(10)		/* F7 */
 #define USART_SR_RTOF		BIT(11)		/* F7 */
@@ -120,8 +119,7 @@ struct stm32_usart_info stm32h7_info = {
 #define USART_SR_SBKF		BIT(18)		/* F7 */
 #define USART_SR_WUF		BIT(20)		/* H7 */
 #define USART_SR_TEACK		BIT(21)		/* F7 */
-#define USART_SR_ERR_MASK	(USART_SR_LBD | USART_SR_ORE | \
-				 USART_SR_FE | USART_SR_PE)
+#define USART_SR_ERR_MASK	(USART_SR_ORE | USART_SR_FE | USART_SR_PE)
 /* Dummy bits */
 #define USART_SR_DUMMY_RX	BIT(16)
 
@@ -168,8 +166,6 @@ struct stm32_usart_info stm32h7_info = {
 /* USART_CR2 */
 #define USART_CR2_ADD_MASK	GENMASK(3, 0)	/* F4 */
 #define USART_CR2_ADDM7		BIT(4)		/* F7 */
-#define USART_CR2_LBDL		BIT(5)
-#define USART_CR2_LBDIE		BIT(6)
 #define USART_CR2_LBCL		BIT(8)
 #define USART_CR2_CPHA		BIT(9)
 #define USART_CR2_CPOL		BIT(10)
@@ -226,12 +222,10 @@ struct stm32_usart_info stm32h7_info = {
 
 /* USART_ICR */
 #define USART_ICR_PECF		BIT(0)		/* F7 */
-#define USART_ICR_FFECF		BIT(1)		/* F7 */
-#define USART_ICR_NCF		BIT(2)		/* F7 */
+#define USART_ICR_FECF		BIT(1)		/* F7 */
 #define USART_ICR_ORECF		BIT(3)		/* F7 */
 #define USART_ICR_IDLECF	BIT(4)		/* F7 */
 #define USART_ICR_TCCF		BIT(6)		/* F7 */
-#define USART_ICR_LBDCF		BIT(8)		/* F7 */
 #define USART_ICR_CTSCF		BIT(9)		/* F7 */
 #define USART_ICR_RTOCF		BIT(11)		/* F7 */
 #define USART_ICR_EOBCF		BIT(12)		/* F7 */
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 375/671] serial: stm32: fix rx data length when parity enabled
       [not found] <20200116170509.12787-1-sashal@kernel.org>
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 373/671] serial: stm32: fix word length configuration Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 374/671] serial: stm32: fix rx error handling Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 376/671] serial: stm32: fix transmit_chars when tx is stopped Sasha Levin
                   ` (7 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit 6c5962f30bce147b1c83869085f3ddde3b34c9e3 ]

- Fixes a rx data error when data length < 8 bits and parity is enabled.
RDR register MSB is used for parity bit reception.
- Adds a mask to ignore MSB when data is get from RDR.

Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 12 ++++++++----
 drivers/tty/serial/stm32-usart.h |  1 +
 2 files changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index f6b739351dde..0a7953e5ce47 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -194,8 +194,8 @@ static int stm32_pending_rx(struct uart_port *port, u32 *sr, int *last_res,
 	return 0;
 }
 
-static unsigned long
-stm32_get_char(struct uart_port *port, u32 *sr, int *last_res)
+static unsigned long stm32_get_char(struct uart_port *port, u32 *sr,
+				    int *last_res)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
@@ -205,10 +205,13 @@ stm32_get_char(struct uart_port *port, u32 *sr, int *last_res)
 		c = stm32_port->rx_buf[RX_BUF_L - (*last_res)--];
 		if ((*last_res) == 0)
 			*last_res = RX_BUF_L;
-		return c;
 	} else {
-		return readl_relaxed(port->membase + ofs->rdr);
+		c = readl_relaxed(port->membase + ofs->rdr);
+		/* apply RDR data mask */
+		c &= stm32_port->rdr_mask;
 	}
+
+	return c;
 }
 
 static void stm32_receive_chars(struct uart_port *port, bool threaded)
@@ -679,6 +682,7 @@ static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
 		cr2 |= USART_CR2_STOP_2B;
 
 	bits = stm32_get_databits(termios);
+	stm32_port->rdr_mask = (BIT(bits) - 1);
 
 	if (cflag & PARENB) {
 		bits++;
diff --git a/drivers/tty/serial/stm32-usart.h b/drivers/tty/serial/stm32-usart.h
index 8d34802e572e..30d2433e27c3 100644
--- a/drivers/tty/serial/stm32-usart.h
+++ b/drivers/tty/serial/stm32-usart.h
@@ -254,6 +254,7 @@ struct stm32_port {
 	bool hw_flow_control;
 	bool fifoen;
 	int wakeirq;
+	int rdr_mask;		/* receive data register mask */
 };
 
 static struct stm32_port stm32_ports[STM32_MAX_PORTS];
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 376/671] serial: stm32: fix transmit_chars when tx is stopped
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (2 preceding siblings ...)
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 375/671] serial: stm32: fix rx data length when parity enabled Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 377/671] serial: stm32: Add support of TC bit status check Sasha Levin
                   ` (6 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit b83b957c91f68e53f0dc596e129e8305761f2a32 ]

Disables the tx irq  when the transmission is ended and updates stop_tx
conditions for code cleanup.

Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 11 +++--------
 1 file changed, 3 insertions(+), 8 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 0a7953e5ce47..2e7757d5e5d8 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -420,13 +420,8 @@ static void stm32_transmit_chars(struct uart_port *port)
 		return;
 	}
 
-	if (uart_tx_stopped(port)) {
-		stm32_stop_tx(port);
-		return;
-	}
-
-	if (uart_circ_empty(xmit)) {
-		stm32_stop_tx(port);
+	if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+		stm32_clr_bits(port, ofs->cr1, USART_CR1_TXEIE);
 		return;
 	}
 
@@ -439,7 +434,7 @@ static void stm32_transmit_chars(struct uart_port *port)
 		uart_write_wakeup(port);
 
 	if (uart_circ_empty(xmit))
-		stm32_stop_tx(port);
+		stm32_clr_bits(port, ofs->cr1, USART_CR1_TXEIE);
 }
 
 static irqreturn_t stm32_interrupt(int irq, void *ptr)
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 377/671] serial: stm32: Add support of TC bit status check
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (3 preceding siblings ...)
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 376/671] serial: stm32: fix transmit_chars when tx is stopped Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 378/671] serial: stm32: fix wakeup source initialization Sasha Levin
                   ` (5 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit 64c32eab660386f9904bb295a104c9c425e9f8b2 ]

Adds a check on the Transmission Complete bit status before closing the
com port. Prevents the port closure before the end of the transmission.
TC poll loop is moved from stm32_tx_dma_complete to stm32_shutdown
routine, in order to check TC before shutdown in both dma and
PIO tx modes.
TC clear is added in stm32_transmit_char routine, in order to be cleared
before transmitting in both dma and PIO tx modes.

Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 2e7757d5e5d8..d603be9669a9 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -290,21 +290,6 @@ static void stm32_tx_dma_complete(void *arg)
 	struct uart_port *port = arg;
 	struct stm32_port *stm32port = to_stm32_port(port);
 	struct stm32_usart_offsets *ofs = &stm32port->info->ofs;
-	unsigned int isr;
-	int ret;
-
-	ret = readl_relaxed_poll_timeout_atomic(port->membase + ofs->isr,
-						isr,
-						(isr & USART_SR_TC),
-						10, 100000);
-
-	if (ret)
-		dev_err(port->dev, "terminal count not set\n");
-
-	if (ofs->icr == UNDEF_REG)
-		stm32_clr_bits(port, ofs->isr, USART_SR_TC);
-	else
-		stm32_set_bits(port, ofs->icr, USART_CR_TC);
 
 	stm32_clr_bits(port, ofs->cr3, USART_CR3_DMAT);
 	stm32port->tx_dma_busy = false;
@@ -396,7 +381,6 @@ static void stm32_transmit_chars_dma(struct uart_port *port)
 	/* Issue pending DMA TX requests */
 	dma_async_issue_pending(stm32port->tx_ch);
 
-	stm32_clr_bits(port, ofs->isr, USART_SR_TC);
 	stm32_set_bits(port, ofs->cr3, USART_CR3_DMAT);
 
 	xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
@@ -425,6 +409,11 @@ static void stm32_transmit_chars(struct uart_port *port)
 		return;
 	}
 
+	if (ofs->icr == UNDEF_REG)
+		stm32_clr_bits(port, ofs->isr, USART_SR_TC);
+	else
+		stm32_set_bits(port, ofs->icr, USART_ICR_TCCF);
+
 	if (stm32_port->tx_ch)
 		stm32_transmit_chars_dma(port);
 	else
@@ -601,12 +590,21 @@ static void stm32_shutdown(struct uart_port *port)
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
 	struct stm32_usart_config *cfg = &stm32_port->info->cfg;
-	u32 val;
+	u32 val, isr;
+	int ret;
 
 	val = USART_CR1_TXEIE | USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
 	val |= BIT(cfg->uart_enable_bit);
 	if (stm32_port->fifoen)
 		val |= USART_CR1_FIFOEN;
+
+	ret = readl_relaxed_poll_timeout(port->membase + ofs->isr,
+					 isr, (isr & USART_SR_TC),
+					 10, 100000);
+
+	if (ret)
+		dev_err(port->dev, "transmission complete not set\n");
+
 	stm32_clr_bits(port, ofs->cr1, val);
 
 	dev_pm_clear_wake_irq(port->dev);
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 378/671] serial: stm32: fix wakeup source initialization
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (4 preceding siblings ...)
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 377/671] serial: stm32: Add support of TC bit status check Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 402/671] serial: stm32: fix a recursive locking in stm32_config_rs485 Sasha Levin
                   ` (4 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Erwan Le Ray, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Erwan Le Ray <erwan.leray@st.com>

[ Upstream commit 5297f274e8b61ceb9676cba6649d3de9d03387ad ]

Fixes dedicated_irq_wakeup issue and deactivated uart as wakeup source by
default.

Fixes: 270e5a74fe4c ("serial: stm32: add wakeup mechanism")
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 28 +++++++++++++++-------------
 1 file changed, 15 insertions(+), 13 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index d603be9669a9..1334e4293977 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -557,7 +557,6 @@ static int stm32_startup(struct uart_port *port)
 {
 	struct stm32_port *stm32_port = to_stm32_port(port);
 	struct stm32_usart_offsets *ofs = &stm32_port->info->ofs;
-	struct stm32_usart_config *cfg = &stm32_port->info->cfg;
 	const char *name = to_platform_device(port->dev)->name;
 	u32 val;
 	int ret;
@@ -568,15 +567,6 @@ static int stm32_startup(struct uart_port *port)
 	if (ret)
 		return ret;
 
-	if (cfg->has_wakeup && stm32_port->wakeirq >= 0) {
-		ret = dev_pm_set_dedicated_wake_irq(port->dev,
-						    stm32_port->wakeirq);
-		if (ret) {
-			free_irq(port->irq, port);
-			return ret;
-		}
-	}
-
 	val = USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
 	if (stm32_port->fifoen)
 		val |= USART_CR1_FIFOEN;
@@ -607,7 +597,6 @@ static void stm32_shutdown(struct uart_port *port)
 
 	stm32_clr_bits(port, ofs->cr1, val);
 
-	dev_pm_clear_wake_irq(port->dev);
 	free_irq(port->irq, port);
 }
 
@@ -1079,11 +1068,18 @@ static int stm32_serial_probe(struct platform_device *pdev)
 		ret = device_init_wakeup(&pdev->dev, true);
 		if (ret)
 			goto err_uninit;
+
+		ret = dev_pm_set_dedicated_wake_irq(&pdev->dev,
+						    stm32port->wakeirq);
+		if (ret)
+			goto err_nowup;
+
+		device_set_wakeup_enable(&pdev->dev, false);
 	}
 
 	ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port);
 	if (ret)
-		goto err_nowup;
+		goto err_wirq;
 
 	ret = stm32_of_dma_rx_probe(stm32port, pdev);
 	if (ret)
@@ -1097,6 +1093,10 @@ static int stm32_serial_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_wirq:
+	if (stm32port->info->cfg.has_wakeup && stm32port->wakeirq >= 0)
+		dev_pm_clear_wake_irq(&pdev->dev);
+
 err_nowup:
 	if (stm32port->info->cfg.has_wakeup && stm32port->wakeirq >= 0)
 		device_init_wakeup(&pdev->dev, false);
@@ -1134,8 +1134,10 @@ static int stm32_serial_remove(struct platform_device *pdev)
 				  TX_BUF_L, stm32_port->tx_buf,
 				  stm32_port->tx_dma_buf);
 
-	if (cfg->has_wakeup && stm32_port->wakeirq >= 0)
+	if (cfg->has_wakeup && stm32_port->wakeirq >= 0) {
+		dev_pm_clear_wake_irq(&pdev->dev);
 		device_init_wakeup(&pdev->dev, false);
+	}
 
 	clk_disable_unprepare(stm32_port->clk);
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 402/671] serial: stm32: fix a recursive locking in stm32_config_rs485
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (5 preceding siblings ...)
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 378/671] serial: stm32: fix wakeup source initialization Sasha Levin
@ 2020-01-16 17:00 ` Sasha Levin
  2020-01-16 17:02 ` [PATCH AUTOSEL 4.19 527/671] tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs Sasha Levin
                   ` (3 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:00 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Borut Seljak, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Borut Seljak <borut.seljak@t-2.net>

[ Upstream commit 707aeea13a9c85520262e11899d86df3c4b48262 ]

Remove spin_lock_irqsave in stm32_config_rs485, it cause recursive locking.
Already locked in uart_set_rs485_config.

Fixes: 1bcda09d291081 ("serial: stm32: add support for RS485 hardware control mode")
Signed-off-by: Borut Seljak <borut.seljak@t-2.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 1334e4293977..d096e552176c 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -105,9 +105,7 @@ static int stm32_config_rs485(struct uart_port *port,
 	struct stm32_usart_config *cfg = &stm32_port->info->cfg;
 	u32 usartdiv, baud, cr1, cr3;
 	bool over8;
-	unsigned long flags;
 
-	spin_lock_irqsave(&port->lock, flags);
 	stm32_clr_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
 
 	port->rs485 = *rs485conf;
@@ -147,7 +145,6 @@ static int stm32_config_rs485(struct uart_port *port,
 	}
 
 	stm32_set_bits(port, ofs->cr1, BIT(cfg->uart_enable_bit));
-	spin_unlock_irqrestore(&port->lock, flags);
 
 	return 0;
 }
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 527/671] tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (6 preceding siblings ...)
  2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 402/671] serial: stm32: fix a recursive locking in stm32_config_rs485 Sasha Levin
@ 2020-01-16 17:02 ` Sasha Levin
  2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 645/671] tty: serial: imx: use the sg count from dma_map_sg Sasha Levin
                   ` (2 subsequent siblings)
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:02 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Andrey Smirnov, Stefan Agner, Bhuvanchandra DV, Chris Healy,
	Cory Tusar, Lucas Stach, Greg Kroah-Hartman, Jiri Slaby,
	linux-imx, linux-serial, Sasha Levin

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit 1da17d7cf8e2c4b60163d54300f72c02f510327c ]

When dealing with 32-bit variant of LPUART IP block appropriate I/O
helpers have to be used to properly deal with endianness
differences. Change all of the offending code to do that.

Fixes: a5fa2660d787 ("tty/serial/fsl_lpuart: Add CONSOLE_POLL support
for lpuart32.")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-imx@nxp.com
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20190729195226.8862-14-andrew.smirnov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/fsl_lpuart.c | 28 ++++++++++++++--------------
 1 file changed, 14 insertions(+), 14 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index ee8a5cb61a5f..2daccb10ae2f 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -528,26 +528,26 @@ static int lpuart32_poll_init(struct uart_port *port)
 	spin_lock_irqsave(&sport->port.lock, flags);
 
 	/* Disable Rx & Tx */
-	writel(0, sport->port.membase + UARTCTRL);
+	lpuart32_write(&sport->port, UARTCTRL, 0);
 
-	temp = readl(sport->port.membase + UARTFIFO);
+	temp = lpuart32_read(&sport->port, UARTFIFO);
 
 	/* Enable Rx and Tx FIFO */
-	writel(temp | UARTFIFO_RXFE | UARTFIFO_TXFE,
-		   sport->port.membase + UARTFIFO);
+	lpuart32_write(&sport->port, UARTFIFO,
+		       temp | UARTFIFO_RXFE | UARTFIFO_TXFE);
 
 	/* flush Tx and Rx FIFO */
-	writel(UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH,
-			sport->port.membase + UARTFIFO);
+	lpuart32_write(&sport->port, UARTFIFO,
+		       UARTFIFO_TXFLUSH | UARTFIFO_RXFLUSH);
 
 	/* explicitly clear RDRF */
-	if (readl(sport->port.membase + UARTSTAT) & UARTSTAT_RDRF) {
-		readl(sport->port.membase + UARTDATA);
-		writel(UARTFIFO_RXUF, sport->port.membase + UARTFIFO);
+	if (lpuart32_read(&sport->port, UARTSTAT) & UARTSTAT_RDRF) {
+		lpuart32_read(&sport->port, UARTDATA);
+		lpuart32_write(&sport->port, UARTFIFO, UARTFIFO_RXUF);
 	}
 
 	/* Enable Rx and Tx */
-	writel(UARTCTRL_RE | UARTCTRL_TE, sport->port.membase + UARTCTRL);
+	lpuart32_write(&sport->port, UARTCTRL, UARTCTRL_RE | UARTCTRL_TE);
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 
 	return 0;
@@ -555,18 +555,18 @@ static int lpuart32_poll_init(struct uart_port *port)
 
 static void lpuart32_poll_put_char(struct uart_port *port, unsigned char c)
 {
-	while (!(readl(port->membase + UARTSTAT) & UARTSTAT_TDRE))
+	while (!(lpuart32_read(port, UARTSTAT) & UARTSTAT_TDRE))
 		barrier();
 
-	writel(c, port->membase + UARTDATA);
+	lpuart32_write(port, UARTDATA, c);
 }
 
 static int lpuart32_poll_get_char(struct uart_port *port)
 {
-	if (!(readl(port->membase + UARTSTAT) & UARTSTAT_RDRF))
+	if (!(lpuart32_read(port, UARTSTAT) & UARTSTAT_RDRF))
 		return NO_POLL_CHAR;
 
-	return readl(port->membase + UARTDATA);
+	return lpuart32_read(port, UARTDATA);
 }
 #endif
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 645/671] tty: serial: imx: use the sg count from dma_map_sg
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (7 preceding siblings ...)
  2020-01-16 17:02 ` [PATCH AUTOSEL 4.19 527/671] tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs Sasha Levin
@ 2020-01-16 17:04 ` Sasha Levin
  2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 646/671] tty: serial: pch_uart: correct usage of dma_unmap_sg Sasha Levin
  2020-01-16 17:05 ` [PATCH AUTOSEL 4.19 670/671] serial: stm32: fix clearing interrupt error flags Sasha Levin
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:04 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Peng Fan, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-arm-kernel

From: Peng Fan <peng.fan@nxp.com>

[ Upstream commit 596fd8dffb745afcebc0ec6968e17fe29f02044c ]

The dmaengine_prep_slave_sg needs to use sg count returned
by dma_map_sg, not use sport->dma_tx_nents, because the return
value of dma_map_sg is not always same with "nents".

Fixes: b4cdc8f61beb ("serial: imx: add DMA support for imx6q")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573108875-26530-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/imx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 989ca7d662f3..672e97978279 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -624,7 +624,7 @@ static void imx_uart_dma_tx(struct imx_port *sport)
 		dev_err(dev, "DMA mapping error for TX.\n");
 		return;
 	}
-	desc = dmaengine_prep_slave_sg(chan, sgl, sport->dma_tx_nents,
+	desc = dmaengine_prep_slave_sg(chan, sgl, ret,
 					DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
 	if (!desc) {
 		dma_unmap_sg(dev, sgl, sport->dma_tx_nents,
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 646/671] tty: serial: pch_uart: correct usage of dma_unmap_sg
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (8 preceding siblings ...)
  2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 645/671] tty: serial: imx: use the sg count from dma_map_sg Sasha Levin
@ 2020-01-16 17:04 ` Sasha Levin
  2020-01-16 17:05 ` [PATCH AUTOSEL 4.19 670/671] serial: stm32: fix clearing interrupt error flags Sasha Levin
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:04 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Peng Fan, Greg Kroah-Hartman, Sasha Levin, linux-serial

From: Peng Fan <peng.fan@nxp.com>

[ Upstream commit 74887542fdcc92ad06a48c0cca17cdf09fc8aa00 ]

Per Documentation/DMA-API-HOWTO.txt,
To unmap a scatterlist, just call:
	dma_unmap_sg(dev, sglist, nents, direction);

.. note::

	The 'nents' argument to the dma_unmap_sg call must be
	the _same_ one you passed into the dma_map_sg call,
	it should _NOT_ be the 'count' value _returned_ from the
	dma_map_sg call.

However in the driver, priv->nent is directly assigned with value
returned from dma_map_sg, and dma_unmap_sg use priv->nent for unmap,
this breaks the API usage.

So introduce a new entry orig_nent to remember 'nents'.

Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1573623259-6339-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/pch_uart.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index cb85002a10d8..3245cdbf9116 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -235,6 +235,7 @@ struct eg20t_port {
 	struct dma_chan			*chan_rx;
 	struct scatterlist		*sg_tx_p;
 	int				nent;
+	int				orig_nent;
 	struct scatterlist		sg_rx;
 	int				tx_dma_use;
 	void				*rx_buf_virt;
@@ -789,9 +790,10 @@ static void pch_dma_tx_complete(void *arg)
 	}
 	xmit->tail &= UART_XMIT_SIZE - 1;
 	async_tx_ack(priv->desc_tx);
-	dma_unmap_sg(port->dev, sg, priv->nent, DMA_TO_DEVICE);
+	dma_unmap_sg(port->dev, sg, priv->orig_nent, DMA_TO_DEVICE);
 	priv->tx_dma_use = 0;
 	priv->nent = 0;
+	priv->orig_nent = 0;
 	kfree(priv->sg_tx_p);
 	pch_uart_hal_enable_interrupt(priv, PCH_UART_HAL_TX_INT);
 }
@@ -1015,6 +1017,7 @@ static unsigned int dma_handle_tx(struct eg20t_port *priv)
 		dev_err(priv->port.dev, "%s:dma_map_sg Failed\n", __func__);
 		return 0;
 	}
+	priv->orig_nent = num;
 	priv->nent = nent;
 
 	for (i = 0; i < nent; i++, sg++) {
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH AUTOSEL 4.19 670/671] serial: stm32: fix clearing interrupt error flags
       [not found] <20200116170509.12787-1-sashal@kernel.org>
                   ` (9 preceding siblings ...)
  2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 646/671] tty: serial: pch_uart: correct usage of dma_unmap_sg Sasha Levin
@ 2020-01-16 17:05 ` Sasha Levin
  10 siblings, 0 replies; 11+ messages in thread
From: Sasha Levin @ 2020-01-16 17:05 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Fabrice Gasnier, Greg Kroah-Hartman, Sasha Levin, linux-serial,
	linux-stm32, linux-arm-kernel

From: Fabrice Gasnier <fabrice.gasnier@st.com>

[ Upstream commit 1250ed7114a977cdc2a67a0c09d6cdda63970eb9 ]

The interrupt clear flag register is a "write 1 to clear" register.
So, only writing ones allows to clear flags:
- Replace buggy stm32_clr_bits() by a simple write to clear error flags
- Replace useless read/modify/write stm32_set_bits() routine by a
  simple write to clear TC (transfer complete) flag.

Fixes: 4f01d833fdcd ("serial: stm32: fix rx error handling")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1574323849-1909-1-git-send-email-fabrice.gasnier@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/stm32-usart.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index d096e552176c..bce4ac1787ad 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -239,8 +239,8 @@ static void stm32_receive_chars(struct uart_port *port, bool threaded)
 		 * cleared by the sequence [read SR - read DR].
 		 */
 		if ((sr & USART_SR_ERR_MASK) && ofs->icr != UNDEF_REG)
-			stm32_clr_bits(port, ofs->icr, USART_ICR_ORECF |
-				       USART_ICR_PECF | USART_ICR_FECF);
+			writel_relaxed(sr & USART_SR_ERR_MASK,
+				       port->membase + ofs->icr);
 
 		c = stm32_get_char(port, &sr, &stm32_port->last_res);
 		port->icount.rx++;
@@ -409,7 +409,7 @@ static void stm32_transmit_chars(struct uart_port *port)
 	if (ofs->icr == UNDEF_REG)
 		stm32_clr_bits(port, ofs->isr, USART_SR_TC);
 	else
-		stm32_set_bits(port, ofs->icr, USART_ICR_TCCF);
+		writel_relaxed(USART_ICR_TCCF, port->membase + ofs->icr);
 
 	if (stm32_port->tx_ch)
 		stm32_transmit_chars_dma(port);
-- 
2.20.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
     [not found] <20200116170509.12787-1-sashal@kernel.org>
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 373/671] serial: stm32: fix word length configuration Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 374/671] serial: stm32: fix rx error handling Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 375/671] serial: stm32: fix rx data length when parity enabled Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 376/671] serial: stm32: fix transmit_chars when tx is stopped Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 377/671] serial: stm32: Add support of TC bit status check Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 378/671] serial: stm32: fix wakeup source initialization Sasha Levin
2020-01-16 17:00 ` [PATCH AUTOSEL 4.19 402/671] serial: stm32: fix a recursive locking in stm32_config_rs485 Sasha Levin
2020-01-16 17:02 ` [PATCH AUTOSEL 4.19 527/671] tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs Sasha Levin
2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 645/671] tty: serial: imx: use the sg count from dma_map_sg Sasha Levin
2020-01-16 17:04 ` [PATCH AUTOSEL 4.19 646/671] tty: serial: pch_uart: correct usage of dma_unmap_sg Sasha Levin
2020-01-16 17:05 ` [PATCH AUTOSEL 4.19 670/671] serial: stm32: fix clearing interrupt error flags Sasha Levin

Linux-Serial Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-serial/0 linux-serial/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-serial linux-serial/ https://lore.kernel.org/linux-serial \
		linux-serial@vger.kernel.org
	public-inbox-index linux-serial

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-serial


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git