[PATCH AUTOSEL 5.8 01/53] ARC: HSDK: wireup perf irq

[PATCH AUTOSEL 5.8 01/53] ARC: HSDK: wireup perf irq

[Sasha Levin]

From: Vineet Gupta <vgupta@synopsys.com>

[ Upstream commit fe81d927b78c4f0557836661d32e41ebc957b024 ]

Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/boot/dts/hsdk.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arc/boot/dts/hsdk.dts b/arch/arc/boot/dts/hsdk.dts
index 9acbeba832c0b..5d64a5a940ee6 100644
--- a/arch/arc/boot/dts/hsdk.dts
+++ b/arch/arc/boot/dts/hsdk.dts
@@ -88,6 +88,8 @@ idu_intc: idu-interrupt-controller {
 
 	arcpct: pct {
 		compatible = "snps,archs-pct";
+		interrupt-parent = <&cpu_intc>;
+		interrupts = <20>;
 	};
 
 	/* TIMER0 with interrupt for clockevent */
-- 
2.25.1


_______________________________________________
linux-snps-arc mailing list
linux-snps-arc@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-snps-arc

[PATCH AUTOSEL 5.8 24/53] ARC: show_regs: fix r12 printing and simplify

[Sasha Levin]

From: Vineet Gupta <vgupta@synopsys.com>

[ Upstream commit e5c388b4b967037a0e00b60194b0dbcf94881a9b ]

when working on ARC64, spotted an issue in ARCv2 reg file printing.
print_reg_file() assumes contiguous reg-file whereas in ARCv2 they are
not: r12 comes before r0-r11 due to hardware auto-save. Apparently this
issue has been present since v2 port submission.

To avoid bolting hacks for this discontinuity while looping through
pt_regs, just ditching the loop and print pt_regs directly.

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/kernel/troubleshoot.c | 77 +++++++++++++---------------------
 1 file changed, 30 insertions(+), 47 deletions(-)

diff --git a/arch/arc/kernel/troubleshoot.c b/arch/arc/kernel/troubleshoot.c
index 28e8bf04b253f..a331bb5d8319f 100644
--- a/arch/arc/kernel/troubleshoot.c
+++ b/arch/arc/kernel/troubleshoot.c
@@ -18,44 +18,37 @@
 
 #define ARC_PATH_MAX	256
 
-/*
- * Common routine to print scratch regs (r0-r12) or callee regs (r13-r25)
- *   -Prints 3 regs per line and a CR.
- *   -To continue, callee regs right after scratch, special handling of CR
- */
-static noinline void print_reg_file(long *reg_rev, int start_num)
+static noinline void print_regs_scratch(struct pt_regs *regs)
 {
-	unsigned int i;
-	char buf[512];
-	int n = 0, len = sizeof(buf);
-
-	for (i = start_num; i < start_num + 13; i++) {
-		n += scnprintf(buf + n, len - n, "r%02u: 0x%08lx\t",
-			       i, (unsigned long)*reg_rev);
-
-		if (((i + 1) % 3) == 0)
-			n += scnprintf(buf + n, len - n, "\n");
-
-		/* because pt_regs has regs reversed: r12..r0, r25..r13 */
-		if (is_isa_arcv2() && start_num == 0)
-			reg_rev++;
-		else
-			reg_rev--;
-	}
-
-	if (start_num != 0)
-		n += scnprintf(buf + n, len - n, "\n\n");
+	pr_cont("BTA: 0x%08lx\n SP: 0x%08lx  FP: 0x%08lx BLK: %pS\n",
+		regs->bta, regs->sp, regs->fp, (void *)regs->blink);
+	pr_cont("LPS: 0x%08lx\tLPE: 0x%08lx\tLPC: 0x%08lx\n",
+		regs->lp_start, regs->lp_end, regs->lp_count);
 
-	/* To continue printing callee regs on same line as scratch regs */
-	if (start_num == 0)
-		pr_info("%s", buf);
-	else
-		pr_cont("%s\n", buf);
+	pr_info("r00: 0x%08lx\tr01: 0x%08lx\tr02: 0x%08lx\n"	\
+		"r03: 0x%08lx\tr04: 0x%08lx\tr05: 0x%08lx\n"	\
+		"r06: 0x%08lx\tr07: 0x%08lx\tr08: 0x%08lx\n"	\
+		"r09: 0x%08lx\tr10: 0x%08lx\tr11: 0x%08lx\n"	\
+		"r12: 0x%08lx\t",
+		regs->r0, regs->r1, regs->r2,
+		regs->r3, regs->r4, regs->r5,
+		regs->r6, regs->r7, regs->r8,
+		regs->r9, regs->r10, regs->r11,
+		regs->r12);
 }
 
-static void show_callee_regs(struct callee_regs *cregs)
+static void print_regs_callee(struct callee_regs *regs)
 {
-	print_reg_file(&(cregs->r13), 13);
+	pr_cont("r13: 0x%08lx\tr14: 0x%08lx\n"			\
+		"r15: 0x%08lx\tr16: 0x%08lx\tr17: 0x%08lx\n"	\
+		"r18: 0x%08lx\tr19: 0x%08lx\tr20: 0x%08lx\n"	\
+		"r21: 0x%08lx\tr22: 0x%08lx\tr23: 0x%08lx\n"	\
+		"r24: 0x%08lx\tr25: 0x%08lx\n",
+		regs->r13, regs->r14,
+		regs->r15, regs->r16, regs->r17,
+		regs->r18, regs->r19, regs->r20,
+		regs->r21, regs->r22, regs->r23,
+		regs->r24, regs->r25);
 }
 
 static void print_task_path_n_nm(struct task_struct *tsk)
@@ -175,7 +168,7 @@ static void show_ecr_verbose(struct pt_regs *regs)
 void show_regs(struct pt_regs *regs)
 {
 	struct task_struct *tsk = current;
-	struct callee_regs *cregs;
+	struct callee_regs *cregs = (struct callee_regs *)tsk->thread.callee_reg;
 
 	/*
 	 * generic code calls us with preemption disabled, but some calls
@@ -204,25 +197,15 @@ void show_regs(struct pt_regs *regs)
 			STS_BIT(regs, A2), STS_BIT(regs, A1),
 			STS_BIT(regs, E2), STS_BIT(regs, E1));
 #else
-	pr_cont(" [%2s%2s%2s%2s]",
+	pr_cont(" [%2s%2s%2s%2s]   ",
 			STS_BIT(regs, IE),
 			(regs->status32 & STATUS_U_MASK) ? "U " : "K ",
 			STS_BIT(regs, DE), STS_BIT(regs, AE));
 #endif
-	pr_cont("  BTA: 0x%08lx\n  SP: 0x%08lx  FP: 0x%08lx BLK: %pS\n",
-		regs->bta, regs->sp, regs->fp, (void *)regs->blink);
-	pr_info("LPS: 0x%08lx\tLPE: 0x%08lx\tLPC: 0x%08lx\n",
-		regs->lp_start, regs->lp_end, regs->lp_count);
-
-	/* print regs->r0 thru regs->r12
-	 * Sequential printing was generating horrible code
-	 */
-	print_reg_file(&(regs->r0), 0);
 
-	/* If Callee regs were saved, display them too */
-	cregs = (struct callee_regs *)current->thread.callee_reg;
+	print_regs_scratch(regs);
 	if (cregs)
-		show_callee_regs(cregs);
+		print_regs_callee(cregs);
 
 	preempt_disable();
 }
-- 
2.25.1


_______________________________________________
linux-snps-arc mailing list
linux-snps-arc@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-snps-arc

[PATCH AUTOSEL 5.8 25/53] irqchip/eznps: Fix build error for !ARC700 builds

[Sasha Levin]

From: Vineet Gupta <vgupta@synopsys.com>

[ Upstream commit 89d29997f103d08264b0685796b420d911658b96 ]

eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.

The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
 - copy AUX_IENABLE from arch/arc header
 - move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/plat-eznps/include/plat/ctop.h | 1 -
 include/soc/nps/common.h                | 6 ++++++
 2 files changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arc/plat-eznps/include/plat/ctop.h b/arch/arc/plat-eznps/include/plat/ctop.h
index a4a61531c7fb9..77712c5ffe848 100644
--- a/arch/arc/plat-eznps/include/plat/ctop.h
+++ b/arch/arc/plat-eznps/include/plat/ctop.h
@@ -33,7 +33,6 @@
 #define CTOP_AUX_DPC				(CTOP_AUX_BASE + 0x02C)
 #define CTOP_AUX_LPC				(CTOP_AUX_BASE + 0x030)
 #define CTOP_AUX_EFLAGS				(CTOP_AUX_BASE + 0x080)
-#define CTOP_AUX_IACK				(CTOP_AUX_BASE + 0x088)
 #define CTOP_AUX_GPA1				(CTOP_AUX_BASE + 0x08C)
 #define CTOP_AUX_UDMC				(CTOP_AUX_BASE + 0x300)
 
diff --git a/include/soc/nps/common.h b/include/soc/nps/common.h
index 9b1d43d671a3f..8c18dc6d3fde5 100644
--- a/include/soc/nps/common.h
+++ b/include/soc/nps/common.h
@@ -45,6 +45,12 @@
 #define CTOP_INST_MOV2B_FLIP_R3_B1_B2_INST	0x5B60
 #define CTOP_INST_MOV2B_FLIP_R3_B1_B2_LIMM	0x00010422
 
+#ifndef AUX_IENABLE
+#define AUX_IENABLE				0x40c
+#endif
+
+#define CTOP_AUX_IACK				(0xFFFFF800 + 0x088)
+
 #ifndef __ASSEMBLY__
 
 /* In order to increase compilation test coverage */
-- 
2.25.1


_______________________________________________
linux-snps-arc mailing list
linux-snps-arc@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-snps-arc

[PATCH AUTOSEL 5.8 41/53] ARC: [plat-hsdk]: Switch ethernet phy-mode to rgmii-id

[Sasha Levin]

From: Evgeniy Didin <Evgeniy.Didin@synopsys.com>

[ Upstream commit 26907eb605fbc3ba9dbf888f21d9d8d04471271d ]

HSDK board has Micrel KSZ9031, recent commit
bcf3440c6dd ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
caused a breakdown of Ethernet.
Using 'phy-mode = "rgmii"' is not correct because accodring RGMII
specification it is necessary to have delay on RX (PHY to MAX)
which is not generated in case of "rgmii".
Using "rgmii-id" adds necessary delay and solves the issue.

Also adding name of PHY placed on HSDK board.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arc/boot/dts/hsdk.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arc/boot/dts/hsdk.dts b/arch/arc/boot/dts/hsdk.dts
index 5d64a5a940ee6..dcaa44e408ace 100644
--- a/arch/arc/boot/dts/hsdk.dts
+++ b/arch/arc/boot/dts/hsdk.dts
@@ -210,7 +210,7 @@ gmac: ethernet@8000 {
 			reg = <0x8000 0x2000>;
 			interrupts = <10>;
 			interrupt-names = "macirq";
-			phy-mode = "rgmii";
+			phy-mode = "rgmii-id";
 			snps,pbl = <32>;
 			snps,multicast-filter-bins = <256>;
 			clocks = <&gmacclk>;
@@ -228,7 +228,7 @@ mdio {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "snps,dwmac-mdio";
-				phy0: ethernet-phy@0 {
+				phy0: ethernet-phy@0 { /* Micrel KSZ9031 */
 					reg = <0>;
 				};
 			};
-- 
2.25.1


_______________________________________________
linux-snps-arc mailing list
linux-snps-arc@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-snps-arc