[PATCH v3 1/5] of: adapt of_find_i2c_driver() to be usable by SPI also

[PATCH v3 1/5] of: adapt of_find_i2c_driver() to be usable by SPI also

[Grant Likely]

From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

SPI has a similar problem as I2C in that it needs to determine an
appropriate modalias value for each device node.  This patch adapts
the of_i2c of_find_i2c_driver() function to be usable by of_spi also.

Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
---

 drivers/of/base.c   |   88 +++++++++++++++++++++++++++++++++++++++++++++++++++
 drivers/of/of_i2c.c |   64 ++-----------------------------------
 include/linux/of.h  |    1 +
 3 files changed, 92 insertions(+), 61 deletions(-)

diff --git a/drivers/of/base.c b/drivers/of/base.c
index 23ffb7c..ad8ac1a 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -385,3 +385,91 @@ struct device_node *of_find_matching_node(struct device_node *from,
 	return np;
 }
 EXPORT_SYMBOL(of_find_matching_node);
+
+/**
+ * of_modalias_table: Table of explicit compatible ==> modalias mappings
+ *
+ * This table allows particulare compatible property values to be mapped
+ * to modalias strings.  This is useful for busses which do not directly
+ * understand the OF device tree but are populated based on data contained
+ * within the device tree.  SPI and I2C are the two current users of this
+ * table.
+ *
+ * In most cases, devices do not need to be listed in this table because
+ * the modalias value can be derived directly from the compatible table.
+ * However, if for any reason a value cannot be derived, then this table
+ * provides a method to override the implicit derivation.
+ *
+ * At the moment, a single table is used for all bus types because it is
+ * assumed that the data size is small and that the compatible values
+ * should already be distinct enough to differentiate between SPI, I2C
+ * and other devices.
+ */
+struct of_modalias_table {
+	char *of_device;
+	char *modalias;
+};
+static struct of_modalias_table of_modalias_table[] = {
+	/* Empty for now; add entries as needed */
+};
+
+/**
+ * of_modalias_node - Lookup appropriate modalias for a device node
+ * @node:	pointer to a device tree node
+ * @modalias:	Pointer to buffer that modalias value will be copied into
+ * @len:	Length of modalias value
+ *
+ * Based on the value of the compatible property, this routine will determine
+ * an appropriate modalias value for a particular device tree node.  Three
+ * separate methods are used to derive a modalias value.
+ *
+ * First method is to lookup the compatible value in of_modalias_table.
+ * Second is to look for a "linux,<modalias>" entry in the compatible list
+ * and used that for modalias.  Third is to strip off the manufacturer
+ * prefix from the first compatible entry and use the remainder as modalias
+ *
+ * This routine returns 0 on success
+ */
+int of_modalias_node(struct device_node *node, char *modalias, int len)
+{
+	int i, cplen;
+	const char *compatible;
+	const char *p;
+
+	/* 1. search for exception list entry */
+	for (i = 0; i < ARRAY_SIZE(of_modalias_table); i++) {
+		compatible = of_modalias_table[i].of_device;
+		if (!of_device_is_compatible(node, compatible))
+			continue;
+		strlcpy(modalias, of_modalias_table[i].modalias, len);
+		return 0;
+	}
+
+	compatible = of_get_property(node, "compatible", &cplen);
+	if (!compatible)
+		return -ENODEV;
+
+	/* 2. search for linux,<modalias> entry */
+	p = compatible;
+	while (cplen > 0) {
+		if (!strncmp(p, "linux,", 6)) {
+			p += 6;
+			strlcpy(modalias, p, len);
+			return 0;
+		}
+
+		i = strlen(p) + 1;
+		p += i;
+		cplen -= i;
+	}
+
+	/* 3. take first compatible entry and strip manufacturer */
+	p = strchr(compatible, ',');
+	if (!p)
+		return -ENODEV;
+	p++;
+	strlcpy(modalias, p, len);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(of_modalias_node);
+
diff --git a/drivers/of/of_i2c.c b/drivers/of/of_i2c.c
index 5c015d3..65fd26d 100644
--- a/drivers/of/of_i2c.c
+++ b/drivers/of/of_i2c.c
@@ -16,62 +16,6 @@
 #include <linux/of_i2c.h>
 #include <linux/module.h>
 
-struct i2c_driver_device {
-	char    *of_device;
-	char    *i2c_type;
-};
-
-static struct i2c_driver_device i2c_devices[] = {
-};
-
-static int of_find_i2c_driver(struct device_node *node,
-			      struct i2c_board_info *info)
-{
-	int i, cplen;
-	const char *compatible;
-	const char *p;
-
-	/* 1. search for exception list entry */
-	for (i = 0; i < ARRAY_SIZE(i2c_devices); i++) {
-		if (!of_device_is_compatible(node, i2c_devices[i].of_device))
-			continue;
-		if (strlcpy(info->type, i2c_devices[i].i2c_type,
-			    I2C_NAME_SIZE) >= I2C_NAME_SIZE)
-			return -ENOMEM;
-
-		return 0;
-	}
-
-	compatible = of_get_property(node, "compatible", &cplen);
-	if (!compatible)
-		return -ENODEV;
-
-	/* 2. search for linux,<i2c-type> entry */
-	p = compatible;
-	while (cplen > 0) {
-		if (!strncmp(p, "linux,", 6)) {
-			p += 6;
-			if (strlcpy(info->type, p,
-				    I2C_NAME_SIZE) >= I2C_NAME_SIZE)
-				return -ENOMEM;
-			return 0;
-		}
-
-		i = strlen(p) + 1;
-		p += i;
-		cplen -= i;
-	}
-
-	/* 3. take fist compatible entry and strip manufacturer */
-	p = strchr(compatible, ',');
-	if (!p)
-		return -ENODEV;
-	p++;
-	if (strlcpy(info->type, p, I2C_NAME_SIZE) >= I2C_NAME_SIZE)
-		return -ENOMEM;
-	return 0;
-}
-
 void of_register_i2c_devices(struct i2c_adapter *adap,
 			     struct device_node *adap_node)
 {
@@ -83,6 +27,9 @@ void of_register_i2c_devices(struct i2c_adapter *adap,
 		const u32 *addr;
 		int len;
 
+		if (of_modalias_node(node, info.type, sizeof(info.type)) < 0)
+			continue;
+
 		addr = of_get_property(node, "reg", &len);
 		if (!addr || len < sizeof(int) || *addr > (1 << 10) - 1) {
 			printk(KERN_ERR
@@ -94,11 +41,6 @@ void of_register_i2c_devices(struct i2c_adapter *adap,
 		if (info.irq == NO_IRQ)
 			info.irq = -1;
 
-		if (of_find_i2c_driver(node, &info) < 0) {
-			irq_dispose_mapping(info.irq);
-			continue;
-		}
-
 		info.addr = *addr;
 
 		request_module(info.type);
diff --git a/include/linux/of.h b/include/linux/of.h
index 59a61bd..79886ad 100644
--- a/include/linux/of.h
+++ b/include/linux/of.h
@@ -70,5 +70,6 @@ extern int of_n_addr_cells(struct device_node *np);
 extern int of_n_size_cells(struct device_node *np);
 extern const struct of_device_id *of_match_node(
 	const struct of_device_id *matches, const struct device_node *node);
+extern int of_modalias_node(struct device_node *node, char *modalias, int len);
 
 #endif /* _LINUX_OF_H */


-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

[PATCH v3 2/5] spi: split up spi_new_device() to allow two stage registration.

[Grant Likely]

From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems.

This patch splits the allocation and registration portions of code out
of spi_new_device() and creates three new functions; spi_alloc_device(),
spi_register_device(), and spi_device_release().  spi_new_device() is
modified to use the new functions for allocation and registration.
None of the existing users of spi_new_device() should be affected by
this change.

Drivers using the new API can forego the use of an spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.

This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.

Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
---

 drivers/spi/spi.c       |  139 ++++++++++++++++++++++++++++++++---------------
 include/linux/spi/spi.h |   10 +++
 2 files changed, 105 insertions(+), 44 deletions(-)

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 32b7a42..e64add0 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -178,6 +178,96 @@ struct boardinfo {
 static LIST_HEAD(board_list);
 static DEFINE_MUTEX(board_lock);
 
+/**
+ * spi_alloc_device - Allocate a new SPI device
+ * @master: Controller to which device is connected
+ * Context: can sleep
+ *
+ * Allows a driver to allocate and initialize and spi_device without
+ * registering it immediately.  This allows a driver to directly
+ * fill the spi_device with device parameters before calling
+ * spi_add_device() on it.
+ *
+ * Caller is responsible to call spi_add_device() on the returned
+ * spi_device structure to add it to the SPI master.  If the caller
+ * needs to discard the spi_device without adding it, then it should
+ * call spi_dev_put() on it.
+ *
+ * Returns a pointer to the new device, or NULL.
+ */
+struct spi_device *spi_alloc_device(struct spi_master *master)
+{
+	struct spi_device	*spi;
+	struct device		*dev = master->dev.parent;
+
+	if (!spi_master_get(master))
+		return NULL;
+
+	spi = kzalloc(sizeof *spi, GFP_KERNEL);
+	if (!spi) {
+		dev_err(dev, "cannot alloc spi_device\n");
+		spi_master_put(master);
+		return NULL;
+	}
+
+	spi->master = master;
+	spi->dev.parent = dev;
+	spi->dev.bus = &spi_bus_type;
+	spi->dev.release = spidev_release;
+	device_initialize(&spi->dev);
+	return spi;
+}
+EXPORT_SYMBOL_GPL(spi_alloc_device);
+
+/**
+ * spi_add_device - Add an spi_device allocated with spi_alloc_device
+ * @spi: spi_device to register
+ *
+ * Companion function to spi_alloc_device.  Devices allocated with
+ * spi_alloc_device can be added onto the spi bus with this function.
+ *
+ * Returns 0 on success; non-zero on failure
+ */
+int spi_add_device(struct spi_device *spi)
+{
+	struct device *dev = spi->master->dev.parent;
+	int status;
+
+	/* Chipselects are numbered 0..max; validate. */
+	if (spi->chip_select >= spi->master->num_chipselect) {
+		dev_err(dev, "cs%d > max %d\n",
+			spi->chip_select,
+			spi->master->num_chipselect);
+		return -EINVAL;
+	}
+
+	/* Set the bus ID string */
+	snprintf(spi->dev.bus_id, sizeof spi->dev.bus_id,
+			"%s.%u", spi->master->dev.bus_id,
+			spi->chip_select);
+
+	/* drivers may modify this initial i/o setup */
+	status = spi->master->setup(spi);
+	if (status < 0) {
+		dev_err(dev, "can't %s %s, status %d\n",
+				"setup", spi->dev.bus_id, status);
+		return status;
+	}
+
+	/* driver core catches callers that misbehave by defining
+	 * devices that already exist.
+	 */
+	status = device_add(&spi->dev);
+	if (status < 0) {
+		dev_err(dev, "can't %s %s, status %d\n",
+				"add", spi->dev.bus_id, status);
+		return status;
+	}
+
+	dev_dbg(dev, "registered child %s\n", spi->dev.bus_id);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(spi_add_device);
 
 /**
  * spi_new_device - instantiate one new SPI device
@@ -197,7 +287,6 @@ struct spi_device *spi_new_device(struct spi_master *master,
 				  struct spi_board_info *chip)
 {
 	struct spi_device	*proxy;
-	struct device		*dev = master->dev.parent;
 	int			status;
 
 	/* NOTE:  caller did any chip->bus_num checks necessary.
@@ -207,66 +296,28 @@ struct spi_device *spi_new_device(struct spi_master *master,
 	 * suggests syslogged diagnostics are best here (ugh).
 	 */
 
-	/* Chipselects are numbered 0..max; validate. */
-	if (chip->chip_select >= master->num_chipselect) {
-		dev_err(dev, "cs%d > max %d\n",
-			chip->chip_select,
-			master->num_chipselect);
-		return NULL;
-	}
-
-	if (!spi_master_get(master))
+	proxy = spi_alloc_device(master);
+	if (!proxy)
 		return NULL;
 
 	WARN_ON(strlen(chip->modalias) >= sizeof(proxy->modalias));
 
-	proxy = kzalloc(sizeof *proxy, GFP_KERNEL);
-	if (!proxy) {
-		dev_err(dev, "can't alloc dev for cs%d\n",
-			chip->chip_select);
-		goto fail;
-	}
-	proxy->master = master;
 	proxy->chip_select = chip->chip_select;
 	proxy->max_speed_hz = chip->max_speed_hz;
 	proxy->mode = chip->mode;
 	proxy->irq = chip->irq;
 	strlcpy(proxy->modalias, chip->modalias, sizeof(proxy->modalias));
-
-	snprintf(proxy->dev.bus_id, sizeof proxy->dev.bus_id,
-			"%s.%u", master->dev.bus_id,
-			chip->chip_select);
-	proxy->dev.parent = dev;
-	proxy->dev.bus = &spi_bus_type;
 	proxy->dev.platform_data = (void *) chip->platform_data;
 	proxy->controller_data = chip->controller_data;
 	proxy->controller_state = NULL;
-	proxy->dev.release = spidev_release;
 
-	/* drivers may modify this initial i/o setup */
-	status = master->setup(proxy);
+	status = spi_add_device(proxy);
 	if (status < 0) {
-		dev_err(dev, "can't %s %s, status %d\n",
-				"setup", proxy->dev.bus_id, status);
-		goto fail;
+		spi_dev_put(proxy);
+		return NULL;
 	}
 
-	/* driver core catches callers that misbehave by defining
-	 * devices that already exist.
-	 */
-	status = device_register(&proxy->dev);
-	if (status < 0) {
-		dev_err(dev, "can't %s %s, status %d\n",
-				"add", proxy->dev.bus_id, status);
-		goto fail;
-	}
-	dev_dbg(dev, "registered child %s\n", proxy->dev.bus_id);
 	return proxy;
-
-fail:
-	spi_master_put(master);
-	kfree(proxy);
-	return NULL;
 }
 EXPORT_SYMBOL_GPL(spi_new_device);
 
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index b55910b..d45967e 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -778,8 +778,18 @@ spi_register_board_info(struct spi_board_info const *info, unsigned n)
  * use spi_new_device() to describe each device.  You can also call
  * spi_unregister_device() to start making that device vanish, but
  * normally that would be handled by spi_unregister_master().
+ *
+ * You can also use spi_alloc_device() and spi_add_device() to
+ * for a two stage registration of an SPI device.  This gives the caller
+ * some more control over the spi_device structure before it is registered
  */
 extern struct spi_device *
+spi_alloc_device(struct spi_master *master);
+
+extern int
+spi_add_device(struct spi_device *spi);
+
+extern struct spi_device *
 spi_new_device(struct spi_master *, struct spi_board_info *);
 
 static inline void


-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

[PATCH v3 3/5] of-bindings: Add binding documentation for SPI busses and devices

[Grant Likely]

From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

Add documentation about how to describe SPI busses in the device tree.

Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
---

 Documentation/powerpc/booting-without-of.txt |   58 ++++++++++++++++++++++++++
 1 files changed, 58 insertions(+), 0 deletions(-)

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index b68684d..3b964ed 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -62,6 +62,7 @@ Table of Contents
       s) Freescale on board FPGA
       t) Freescael MSI interrupt controller
       u) Freescale General-purpose Timers Module
+      v) SPI busses
 
   VII - Marvell Discovery mv64[345]6x System Controller chips
     1) The /system-controller node
@@ -2967,6 +2968,63 @@ platforms are moved over to use the flattened-device-tree model.
 	clock-frequency = <0>;
     };
 
+    v) SPI (Serial Peripheral Interface) busses
+
+    SPI busses can be described with a node for the SPI master device
+    and a set of child nodes for each SPI slave on the bus.  For this
+    discussion, it is assumed that the system's SPI controller is in
+    SPI master mode.  This binding does not describe SPI controllers
+    in slave mode.
+
+    The SPI master node requires the following properties:
+    - #address-cells  - number of cells required to define a chip select
+			address on the SPI bus.
+    - #size-cells     - should be zero.
+    - compatible      - name of SPI bus controller following generic names
+			recommended practice.
+    No other properties are required in the SPI bus node.  It is assumed
+    that a driver for an SPI bus device will understand that it is an SPI bus.
+    However, the binding does not attempt to define the specific method for
+    assigning chip select numbers.  Since SPI chip select configuration is
+    flexible and non-standardized, it is left out of this binding with the
+    assumption that board specific platform code will be used to manage
+    chip selects.  Individual drivers can define additional properties to
+    support describing the chip select layout.
+
+    SPI slave nodes must be children of the SPI master node and can
+    contain the following properties.
+    - reg             - (required) chip select address of device.
+    - compatible      - (required) name of SPI device following generic names
+			recommended practice
+    - spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz
+    - spi-cpol        - (optional) Empty property indicating device requires
+			inverse clock polarity (CPOL) mode
+    - spi-cpha        - (optional) Empty property indicating device requires
+			shifted clock phase (CPHA) mode
+
+    SPI example for an MPC5200 SPI bus:
+		spi@f00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+			reg = <0xf00 0x20>;
+			interrupts = <2 13 0 2 14 0>;
+			interrupt-parent = <&mpc5200_pic>;
+
+			ethernet-switch@0 {
+				compatible = "micrel,ks8995m";
+				spi-max-frequency = <1000000>;
+				reg = <0>;
+			};
+
+			codec@1 {
+				compatible = "ti,tlv320aic26";
+				spi-max-frequency = <100000>;
+				reg = <1>;
+			};
+		};
+
+
 VII - Marvell Discovery mv64[345]6x System Controller chips
 ===========================================================
 


-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

[PATCH v3 4/5] spi: Add OF binding support for SPI busses

[Grant Likely]

From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

This patch adds support for populating an SPI bus based on data in the
OF device tree.  This is useful for powerpc platforms which use the
device tree instead of discrete code for describing platform layout.

Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
---

 drivers/of/Kconfig     |    6 +++
 drivers/of/Makefile    |    1 +
 drivers/of/of_spi.c    |   93 ++++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/of_spi.h |   18 +++++++++
 4 files changed, 118 insertions(+), 0 deletions(-)

diff --git a/drivers/of/Kconfig b/drivers/of/Kconfig
index 3a7a11a..edd6e92 100644
--- a/drivers/of/Kconfig
+++ b/drivers/of/Kconfig
@@ -13,3 +13,9 @@ config OF_I2C
 	depends on PPC_OF && I2C
 	help
 	  OpenFirmware I2C accessors
+
+config OF_SPI
+	def_tristate SPI
+	depends on OF && PPC_OF && SPI
+	help
+	  OpenFirmware SPI accessors
diff --git a/drivers/of/Makefile b/drivers/of/Makefile
index 548772e..4c3c6f8 100644
--- a/drivers/of/Makefile
+++ b/drivers/of/Makefile
@@ -2,3 +2,4 @@ obj-y = base.o
 obj-$(CONFIG_OF_DEVICE) += device.o platform.o
 obj-$(CONFIG_OF_GPIO)   += gpio.o
 obj-$(CONFIG_OF_I2C)	+= of_i2c.o
+obj-$(CONFIG_OF_SPI)	+= of_spi.o
diff --git a/drivers/of/of_spi.c b/drivers/of/of_spi.c
new file mode 100644
index 0000000..b01eec0
--- /dev/null
+++ b/drivers/of/of_spi.c
@@ -0,0 +1,93 @@
+/*
+ * SPI OF support routines
+ * Copyright (C) 2008 Secret Lab Technologies Ltd.
+ *
+ * Support routines for deriving SPI device attachments from the device
+ * tree.
+ */
+
+#include <linux/of.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/of_spi.h>
+
+/**
+ * of_register_spi_devices - Register child devices onto the SPI bus
+ * @master:	Pointer to spi_master device
+ * @np:		parent node of SPI device nodes
+ *
+ * Registers an spi_device for each child node of 'np' which has a 'reg'
+ * property.
+ */
+void of_register_spi_devices(struct spi_master *master, struct device_node *np)
+{
+	struct spi_device *spi;
+	struct device_node *nc;
+	const u32 *prop;
+	int rc;
+	int len;
+
+	for_each_child_of_node(np, nc) {
+		/* Alloc an spi_device */
+		spi = spi_alloc_device(master);
+		if (!spi) {
+			dev_err(&master->dev, "spi_device alloc error for %s\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+
+		/* Select device driver */
+		if (of_modalias_node(nc, spi->modalias,
+				     sizeof(spi->modalias)) < 0) {
+			dev_err(&master->dev, "cannot find modalias for %s\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+
+		/* Device address */
+		prop = of_get_property(nc, "reg", &len);
+		if (!prop || len < sizeof(*prop)) {
+			dev_err(&master->dev, "%s has no 'reg' property\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+		spi->chip_select = *prop;
+
+		/* Mode (clock phase/polarity/etc.) */
+		if (of_find_property(nc, "spi-cpha", NULL))
+			spi->mode |= SPI_CPHA;
+		if (of_find_property(nc, "spi-cpol", NULL))
+			spi->mode |= SPI_CPOL;
+
+		/* Device speed */
+		prop = of_get_property(nc, "spi-max-frequency", &len);
+		if (!prop || len < sizeof(*prop)) {
+			dev_err(&master->dev, "%s has no 'spi-max-frequency' property\n",
+				nc->full_name);
+			spi_dev_put(spi);
+			continue;
+		}
+		spi->max_speed_hz = *prop;
+
+		/* IRQ */
+		spi->irq = irq_of_parse_and_map(nc, 0);
+
+		/* Store a pointer to the node in the device structure */
+		of_node_get(nc);
+		spi->dev.archdata.of_node = nc;
+
+		/* Register the new device */
+		request_module(spi->modalias);
+		rc = spi_add_device(spi);
+		if (rc) {
+			dev_err(&master->dev, "spi_device register error %s\n",
+				nc->full_name);
+			spi_dev_put(spi);
+		}
+
+	}
+}
+EXPORT_SYMBOL(of_register_spi_devices);
diff --git a/include/linux/of_spi.h b/include/linux/of_spi.h
new file mode 100644
index 0000000..5f71ee8
--- /dev/null
+++ b/include/linux/of_spi.h
@@ -0,0 +1,18 @@
+/*
+ * OpenFirmware SPI support routines
+ * Copyright (C) 2008 Secret Lab Technologies Ltd.
+ *
+ * Support routines for deriving SPI device attachments from the device
+ * tree.
+ */
+
+#ifndef __LINUX_OF_SPI_H
+#define __LINUX_OF_SPI_H
+
+#include <linux/of.h>
+#include <linux/spi/spi.h>
+
+extern void of_register_spi_devices(struct spi_master *master,
+				    struct device_node *np);
+
+#endif /* __LINUX_OF_SPI */


-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

[PATCH v3 5/5] powerpc/mpc5200: Add mpc5200-spi (non-PSC) device driver

[Grant Likely]

From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

Adds support for the dedicated SPI device on the Freescale MPC5200(b)
SoC.

Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
---

 drivers/spi/Kconfig             |    8 +
 drivers/spi/Makefile            |    1 
 drivers/spi/mpc52xx_spi.c       |  595 +++++++++++++++++++++++++++++++++++++++
 include/linux/spi/mpc52xx_spi.h |   10 +
 4 files changed, 614 insertions(+), 0 deletions(-)

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 66ec5d8..01860ac 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -116,6 +116,14 @@ config SPI_LM70_LLP
 	  which interfaces to an LM70 temperature sensor using
 	  a parallel port.
 
+config SPI_MPC52xx
+	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
+	depends on PPC_MPC52xx && SPI
+	select SPI_MASTER_OF
+	help
+	  This drivers supports the MPC52xx SPI controller in master SPI
+	  mode.
+
 config SPI_MPC52xx_PSC
 	tristate "Freescale MPC52xx PSC SPI controller"
 	depends on SPI_MASTER && PPC_MPC52xx && EXPERIMENTAL
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 7fca043..340b878 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -22,6 +22,7 @@ obj-$(CONFIG_SPI_PXA2XX)		+= pxa2xx_spi.o
 obj-$(CONFIG_SPI_OMAP_UWIRE)		+= omap_uwire.o
 obj-$(CONFIG_SPI_OMAP24XX)		+= omap2_mcspi.o
 obj-$(CONFIG_SPI_MPC52xx_PSC)		+= mpc52xx_psc_spi.o
+obj-$(CONFIG_SPI_MPC52xx)		+= mpc52xx_spi.o
 obj-$(CONFIG_SPI_MPC83xx)		+= spi_mpc83xx.o
 obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx.o
diff --git a/drivers/spi/mpc52xx_spi.c b/drivers/spi/mpc52xx_spi.c
new file mode 100644
index 0000000..453690f
--- /dev/null
+++ b/drivers/spi/mpc52xx_spi.c
@@ -0,0 +1,595 @@
+/*
+ * MPC52xx SPI master driver.
+ * Copyright (C) 2008 Secret Lab Technologies Ltd.
+ *
+ * This is the driver for the MPC5200's dedicated SPI device (not for a
+ * PSC in SPI mode)
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/of_platform.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/mpc52xx_spi.h>
+#include <linux/of_spi.h>
+#include <linux/io.h>
+#include <asm/time.h>
+#include <asm/mpc52xx.h>
+
+MODULE_AUTHOR("Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>");
+MODULE_DESCRIPTION("MPC52xx SPI (non-PSC) Driver");
+MODULE_LICENSE("GPL");
+
+/* Register offsets */
+#define SPI_CTRL1	0x00
+#define SPI_CTRL1_SPIE		(1 << 7)
+#define SPI_CTRL1_SPE		(1 << 6)
+#define SPI_CTRL1_MSTR		(1 << 4)
+#define SPI_CTRL1_CPOL		(1 << 3)
+#define SPI_CTRL1_CPHA		(1 << 2)
+#define SPI_CTRL1_SSOE		(1 << 1)
+#define SPI_CTRL1_LSBFE		(1 << 0)
+
+#define SPI_CTRL2	0x01
+#define SPI_BRR		0x04
+
+#define SPI_STATUS	0x05
+#define SPI_STATUS_SPIF		(1 << 7)
+#define SPI_STATUS_WCOL		(1 << 6)
+#define SPI_STATUS_MODF		(1 << 4)
+
+#define SPI_DATA	0x09
+#define SPI_PORTDATA	0x0d
+#define SPI_DATADIR	0x10
+
+/* FSM state return values */
+#define FSM_STOP	0
+#define FSM_POLL	1
+#define FSM_CONTINUE	2
+
+/* Driver internal data */
+struct mpc52xx_spi {
+	struct spi_master *master;
+	u32 sysclk;
+	void __iomem *regs;
+	int irq0;	/* MODF irq */
+	int irq1;	/* SPIF irq */
+	int ipb_freq;
+
+	/* Statistics */
+	int msg_count;
+	int wcol_count;
+	int wcol_ticks;
+	u32 wcol_tx_timestamp;
+	int modf_count;
+	int byte_count;
+
+	/* Hooks for platform modification of behaviour */
+	void (*premessage)(struct spi_message *m, void *context);
+	void *premessage_context;
+
+	struct list_head queue;		/* queue of pending messages */
+	spinlock_t lock;
+	struct work_struct work;
+
+
+	/* Details of current transfer (length, and buffer pointers) */
+	struct spi_message *message;	/* current message */
+	struct spi_transfer *transfer;	/* current transfer */
+	int (*state)(int irq, struct mpc52xx_spi *ms, u8 status, u8 data);
+	int len;
+	int timestamp;
+	u8 *rx_buf;
+	const u8 *tx_buf;
+	int cs_change;
+};
+
+/*
+ * CS control function
+ */
+static void mpc52xx_spi_chipsel(struct mpc52xx_spi *ms, int value)
+{
+	if (value)
+		writeb(0, ms->regs + SPI_PORTDATA); /* Assert SS pin */
+	else
+		writeb(0x08, ms->regs + SPI_PORTDATA); /* Deassert SS pin */
+}
+
+/*
+ * Start a new transfer.  This is called both by the idle state
+ * for the first transfer in a message, and by the wait state when the
+ * previous transfer in a message is complete.
+ */
+static void mpc52xx_spi_start_transfer(struct mpc52xx_spi *ms)
+{
+	ms->rx_buf = ms->transfer->rx_buf;
+	ms->tx_buf = ms->transfer->tx_buf;
+	ms->len = ms->transfer->len;
+
+	/* Activate the chip select */
+	if (ms->cs_change)
+		mpc52xx_spi_chipsel(ms, 1);
+	ms->cs_change = ms->transfer->cs_change;
+
+	/* Write out the first byte */
+	ms->wcol_tx_timestamp = get_tbl();
+	if (ms->tx_buf)
+		writeb(*ms->tx_buf++, ms->regs + SPI_DATA);
+	else
+		writeb(0, ms->regs + SPI_DATA);
+}
+
+/* Forward declaration of state handlers */
+static int mpc52xx_spi_fsmstate_transfer(int irq, struct mpc52xx_spi *ms,
+					 u8 status, u8 data);
+static int mpc52xx_spi_fsmstate_wait(int irq, struct mpc52xx_spi *ms,
+				     u8 status, u8 data);
+
+/*
+ * IDLE state
+ *
+ * No transfers are in progress; if another transfer is pending then retrieve
+ * it and kick it off.  Otherwise, stop processing the state machine
+ */
+static int
+mpc52xx_spi_fsmstate_idle(int irq, struct mpc52xx_spi *ms, u8 status, u8 data)
+{
+	struct spi_message *m;
+	struct spi_device *spi;
+	int spr, sppr;
+	u8 ctrl1;
+
+	if (status && (irq != NO_IRQ))
+		dev_err(&ms->master->dev, "spurious irq, status=0x%.2x\n",
+			status);
+
+	/* Check if there is another transfer waiting */
+	if (list_empty(&ms->queue))
+		return FSM_STOP;
+
+	/* Get the next message */
+	spin_lock(&ms->lock);
+
+	/* Call the pre-message hook with a pointer to the next
+	 * message.  The pre-message hook may enqueue a new message for
+	 * changing the chip select value to the head of the queue */
+	m = list_first_entry(&ms->queue, struct spi_message, queue);
+	if (ms->premessage)
+		ms->premessage(m, ms->premessage_context);
+
+	/* reget the head of the queue (the premessage hook may have enqueued
+	 * something before it.) and drop the spinlock */
+	ms->message = list_first_entry(&ms->queue, struct spi_message, queue);
+	list_del_init(&ms->message->queue);
+	spin_unlock(&ms->lock);
+
+	/* Setup the controller parameters */
+	ctrl1 = SPI_CTRL1_SPIE | SPI_CTRL1_SPE | SPI_CTRL1_MSTR;
+	spi = ms->message->spi;
+	if (spi->mode & SPI_CPHA)
+		ctrl1 |= SPI_CTRL1_CPHA;
+	if (spi->mode & SPI_CPOL)
+		ctrl1 |= SPI_CTRL1_CPOL;
+	if (spi->mode & SPI_LSB_FIRST)
+		ctrl1 |= SPI_CTRL1_LSBFE;
+	writeb(ctrl1, ms->regs + SPI_CTRL1);
+
+	/* Setup the controller speed */
+	/* minimum divider is '2'.  Also, add '1' to force rounding up. */
+	sppr = ((ms->ipb_freq / ms->message->spi->max_speed_hz) + 1) >> 1;
+	spr = 0;
+	if (sppr < 1)
+		sppr = 1;
+	while (((sppr - 1) & ~0x7) != 0) {
+		sppr = (sppr + 1) >> 1; /* add '1' to force rounding up */
+		spr++;
+	}
+	sppr--;		/* sppr quantity in register is offset by 1 */
+	if (spr > 7) {
+		/* Don't overrun limits of SPI baudrate register */
+		spr = 7;
+		sppr = 7;
+	}
+	writeb(sppr << 4 | spr, ms->regs + SPI_BRR); /* Set speed */
+
+	ms->cs_change = 1;
+	ms->transfer = container_of(ms->message->transfers.next,
+				    struct spi_transfer, transfer_list);
+
+	mpc52xx_spi_start_transfer(ms);
+	ms->state = mpc52xx_spi_fsmstate_transfer;
+
+#if defined(VERBOSE_DEBUG)
+	dev_info(&ms->master->dev, "msg:%p, max_speed:%i, brr:%.2x\n",
+		 ms->message, ms->message->spi->max_speed_hz,
+		 readb(ms->regs + SPI_BRR));
+#endif
+
+	return FSM_CONTINUE;
+}
+
+/*
+ * TRANSFER state
+ *
+ * In the middle of a transfer.  If the SPI core has completed processing
+ * a byte, then read out the received data and write out the next byte
+ * (unless this transfer is finished; in which case go on to the wait
+ * state)
+ */
+static int mpc52xx_spi_fsmstate_transfer(int irq, struct mpc52xx_spi *ms,
+					 u8 status, u8 data)
+{
+	if (!status)
+		return ms->irq0 == NO_IRQ ? FSM_POLL : FSM_STOP;
+
+	if (status & SPI_STATUS_WCOL) {
+		/* The SPI device is stoopid.  At slower speeds, it may raise
+		 * the SPIF flag before the state machine is actually finished.
+		 * which causes a collision (internal to the state machine
+		 * only).  The manual recommends inserting a delay between
+		 * receving the interrupt and sending the next byte, but
+		 * it can also be worked around simply by retrying the
+		 * transfer which is what we do here. */
+		ms->wcol_count++;
+		ms->wcol_ticks += get_tbl() - ms->wcol_tx_timestamp;
+		ms->wcol_tx_timestamp = get_tbl();
+		data = 0;
+		if (ms->tx_buf)
+			data = *(ms->tx_buf-1);
+		writeb(data, ms->regs + SPI_DATA); /* try again */
+		return FSM_CONTINUE;
+	} else if (status & SPI_STATUS_MODF) {
+		ms->modf_count++;
+		dev_err(&ms->master->dev, "mod fault\n");
+		mpc52xx_spi_chipsel(ms, 0);
+		ms->message->status = -EIO;
+		if (ms->message->complete)
+			ms->message->complete(ms->message->context);
+		ms->state = mpc52xx_spi_fsmstate_idle;
+		return FSM_CONTINUE;
+	}
+
+	/* Read data out of the spi device */
+	ms->byte_count++;
+	if (ms->rx_buf)
+		*ms->rx_buf++ = data;
+
+	/* Is the transfer complete? */
+	ms->len--;
+	if (ms->len == 0) {
+		ms->timestamp = get_tbl();
+		ms->timestamp += ms->transfer->delay_usecs * tb_ticks_per_usec;
+		ms->state = mpc52xx_spi_fsmstate_wait;
+		return FSM_CONTINUE;
+	}
+
+	/* Write out the next byte */
+	ms->wcol_tx_timestamp = get_tbl();
+	if (ms->tx_buf)
+		writeb(*ms->tx_buf++, ms->regs + SPI_DATA);
+	else
+		writeb(0, ms->regs + SPI_DATA);
+
+	return FSM_CONTINUE;
+}
+
+/*
+ * WAIT state
+ *
+ * A transfer has completed; need to wait for the delay period to complete
+ * before starting the next transfer
+ */
+static int
+mpc52xx_spi_fsmstate_wait(int irq, struct mpc52xx_spi *ms, u8 status, u8 data)
+{
+	if (status && irq != NO_IRQ)
+		dev_err(&ms->master->dev, "spurious irq, status=0x%.2x\n",
+			status);
+
+	if (((int)get_tbl()) - ms->timestamp < 0)
+		return FSM_POLL;
+
+	ms->message->actual_length += ms->transfer->len;
+
+	/* Check if there is another transfer in this message.  If there
+	 * aren't then deactivate CS, notify sender, and drop back to idle
+	 * to start the next message. */
+	if (ms->transfer->transfer_list.next == &ms->message->transfers) {
+		ms->msg_count++;
+		mpc52xx_spi_chipsel(ms, 0);
+		ms->message->status = 0;
+		if (ms->message->complete)
+			ms->message->complete(ms->message->context);
+		ms->state = mpc52xx_spi_fsmstate_idle;
+		return FSM_CONTINUE;
+	}
+
+	/* There is another transfer; kick it off */
+
+	if (ms->cs_change)
+		mpc52xx_spi_chipsel(ms, 0);
+
+	ms->transfer = container_of(ms->transfer->transfer_list.next,
+				    struct spi_transfer, transfer_list);
+	mpc52xx_spi_start_transfer(ms);
+	ms->state = mpc52xx_spi_fsmstate_transfer;
+	return FSM_CONTINUE;
+}
+
+/*
+ * IRQ handler
+ */
+static irqreturn_t mpc52xx_spi_irq(int irq, void *_ms)
+{
+	struct mpc52xx_spi *ms = _ms;
+	int rc = FSM_CONTINUE;
+	u8 status, data;
+
+	while (rc == FSM_CONTINUE) {
+		/* Interrupt cleared by read of STATUS followed by
+		 * read of DATA registers*/
+		status = readb(ms->regs + SPI_STATUS);
+		data = readb(ms->regs + SPI_DATA); /* clear status */
+		rc = ms->state(irq, ms, status, data);
+	}
+
+	if (rc == FSM_POLL)
+		schedule_work(&ms->work);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Workqueue method of running the state machine
+ */
+static void mpc52xx_spi_wq(struct work_struct *work)
+{
+	struct mpc52xx_spi *ms = container_of(work, struct mpc52xx_spi, work);
+	mpc52xx_spi_irq(NO_IRQ, ms);
+}
+
+/*
+ * spi_master callbacks
+ */
+
+static int mpc52xx_spi_setup(struct spi_device *spi)
+{
+	return 0;
+}
+
+static int mpc52xx_spi_transfer(struct spi_device *spi, struct spi_message *m)
+{
+	struct mpc52xx_spi *ms = spi_master_get_devdata(spi->master);
+	unsigned long flags;
+
+	m->actual_length = 0;
+	m->status = -EINPROGRESS;
+
+	spin_lock_irqsave(&ms->lock, flags);
+	list_add_tail(&m->queue, &ms->queue);
+	spin_unlock_irqrestore(&ms->lock, flags);
+	schedule_work(&ms->work);
+
+	return 0;
+}
+
+/*
+ * Hook to modify premessage hook
+ */
+void mpc52xx_spi_set_premessage_hook(struct spi_master *master,
+				     void (*hook)(struct spi_message *m,
+						  void *context),
+				     void *hook_context)
+{
+	struct mpc52xx_spi *ms = spi_master_get_devdata(master);
+	ms->premessage = hook;
+	ms->premessage_context = hook_context;
+}
+EXPORT_SYMBOL(mpc52xx_spi_set_premessage_hook);
+
+/*
+ * SysFS files
+ */
+static int
+*mpc52xx_spi_sysfs_get_counter(struct mpc52xx_spi *ms, const char *name)
+{
+	if (strcmp(name, "msg_count") == 0)
+		return &ms->msg_count;
+	if (strcmp(name, "byte_count") == 0)
+		return &ms->byte_count;
+	if (strcmp(name, "wcol_count") == 0)
+		return &ms->wcol_count;
+	if (strcmp(name, "wcol_ticks") == 0)
+		return &ms->wcol_ticks;
+	if (strcmp(name, "modf_count") == 0)
+		return &ms->modf_count;
+	return NULL;
+}
+
+static ssize_t mpc52xx_spi_show_count(struct device *dev,
+				      struct device_attribute *attr,
+				      char *buf)
+{
+	struct spi_master *master = container_of(dev, struct spi_master, dev);
+	struct mpc52xx_spi *ms = spi_master_get_devdata(master);
+	int *counter;
+
+	counter = mpc52xx_spi_sysfs_get_counter(ms, attr->attr.name);
+	if (!counter)
+		return sprintf(buf, "error\n");
+	return sprintf(buf, "%d\n", *counter);
+}
+
+static ssize_t mpc52xx_spi_set_count(struct device *dev,
+				     struct device_attribute *attr,
+				     const char *buf, size_t count)
+{
+	struct spi_master *master = container_of(dev, struct spi_master, dev);
+	struct mpc52xx_spi *ms = spi_master_get_devdata(master);
+	int *counter;
+	int value = simple_strtoul(buf, NULL, 0);
+
+	counter = mpc52xx_spi_sysfs_get_counter(ms, attr->attr.name);
+	if (counter)
+		*counter = value;
+	return count;
+}
+
+DEVICE_ATTR(msg_count, 0644, mpc52xx_spi_show_count, mpc52xx_spi_set_count);
+DEVICE_ATTR(byte_count, 0644, mpc52xx_spi_show_count, mpc52xx_spi_set_count);
+DEVICE_ATTR(wcol_count, 0644, mpc52xx_spi_show_count, mpc52xx_spi_set_count);
+DEVICE_ATTR(wcol_ticks, 0644, mpc52xx_spi_show_count, mpc52xx_spi_set_count);
+DEVICE_ATTR(modf_count, 0644, mpc52xx_spi_show_count, mpc52xx_spi_set_count);
+
+/*
+ * OF Platform Bus Binding
+ */
+static int __devinit mpc52xx_spi_of_probe(struct of_device *op,
+					  const struct of_device_id *match)
+{
+	struct spi_master *master;
+	struct mpc52xx_spi *ms;
+	void __iomem *regs;
+	const u32 *prop;
+	int rc, len;
+
+	/* MMIO registers */
+	dev_dbg(&op->dev, "probing mpc5200 SPI device\n");
+	regs = of_iomap(op->node, 0);
+	if (!regs)
+		return -ENODEV;
+
+	/* initialize the device */
+	writeb(SPI_CTRL1_SPIE | SPI_CTRL1_SPE | SPI_CTRL1_MSTR, regs+SPI_CTRL1);
+	writeb(0x0, regs + SPI_CTRL2);
+	writeb(0xe, regs + SPI_DATADIR);	/* Set output pins */
+	writeb(0x8, regs + SPI_PORTDATA);	/* Deassert /SS signal */
+
+	/* Clear the status register and re-read it to check for a MODF
+	 * failure.  This driver cannot currently handle multiple masters
+	 * on the SPI bus.  This fault will also occur if the SPI signals
+	 * are not connected to any pins (port_config setting) */
+	readb(regs + SPI_STATUS);
+	readb(regs + SPI_DATA);
+	if (readb(regs + SPI_STATUS) & SPI_STATUS_MODF) {
+		dev_err(&op->dev, "mode fault; is port_config correct?\n");
+		return -EIO;
+	}
+
+	dev_dbg(&op->dev, "allocating spi_master struct\n");
+	master = spi_alloc_master(&op->dev, sizeof *ms);
+	if (!master)
+		return -ENOMEM;
+	master->bus_num = -1;
+	master->num_chipselect = 1;
+	prop = of_get_property(op->node, "num-slaves", &len);
+	if (prop && len >= sizeof(*prop))
+		master->num_chipselect = *prop;
+
+	master->setup = mpc52xx_spi_setup;
+	master->transfer = mpc52xx_spi_transfer;
+	dev_set_drvdata(&op->dev, master);
+
+	ms = spi_master_get_devdata(master);
+	ms->master = master;
+	ms->regs = regs;
+	ms->irq0 = irq_of_parse_and_map(op->node, 0);
+	ms->irq1 = irq_of_parse_and_map(op->node, 1);
+	ms->state = mpc52xx_spi_fsmstate_idle;
+	ms->ipb_freq = mpc52xx_find_ipb_freq(op->node);
+	spin_lock_init(&ms->lock);
+	INIT_LIST_HEAD(&ms->queue);
+	INIT_WORK(&ms->work, mpc52xx_spi_wq);
+
+	dev_dbg(&op->dev, "registering spi_master struct\n");
+	rc = spi_register_master(master);
+	if (rc < 0)
+		goto err_register;
+
+	/* Decide if interrupts can be used */
+	if ((ms->irq0 != NO_IRQ) && (ms->irq1 != NO_IRQ)) {
+		rc = request_irq(ms->irq0, mpc52xx_spi_irq, IRQF_SAMPLE_RANDOM,
+				  "mpc5200-spi-modf", ms);
+		rc |= request_irq(ms->irq1, mpc52xx_spi_irq, IRQF_SAMPLE_RANDOM,
+				  "mpc5200-spi-spiF", ms);
+		if (rc) {
+			free_irq(ms->irq0, ms);
+			free_irq(ms->irq1, ms);
+			ms->irq0 = ms->irq1 = NO_IRQ;
+			dev_info(&op->dev, "using polled mode\n");
+		}
+	} else {
+		/* operate in polled mode */
+		ms->irq0 = ms->irq1 = NO_IRQ;
+		dev_info(&op->dev, "using polled mode\n");
+	}
+
+	/* Create SysFS files */
+	rc = device_create_file(&ms->master->dev, &dev_attr_msg_count);
+	rc |= device_create_file(&ms->master->dev, &dev_attr_byte_count);
+	rc |= device_create_file(&ms->master->dev, &dev_attr_wcol_count);
+	rc |= device_create_file(&ms->master->dev, &dev_attr_wcol_ticks);
+	rc |= device_create_file(&ms->master->dev, &dev_attr_modf_count);
+	if (rc)
+		dev_info(&ms->master->dev, "error creating sysfs files\n");
+
+	dev_info(&ms->master->dev, "registered MPC5200 SPI bus\n");
+
+	of_register_spi_devices(master, op->node);
+
+	return rc;
+
+ err_register:
+	dev_err(&ms->master->dev, "initialization failed\n");
+	spi_master_put(master);
+	return rc;
+}
+
+static void __devexit mpc52xx_spi_of_remove(struct of_device *op)
+{
+	struct spi_master *master = dev_get_drvdata(&op->dev);
+	struct mpc52xx_spi *ms = spi_master_get_devdata(master);
+
+	device_remove_file(&ms->master->dev, &dev_attr_msg_count);
+	device_remove_file(&ms->master->dev, &dev_attr_byte_count);
+	device_remove_file(&ms->master->dev, &dev_attr_wcol_count);
+	device_remove_file(&ms->master->dev, &dev_attr_wcol_ticks);
+	device_remove_file(&ms->master->dev, &dev_attr_modf_count);
+
+	free_irq(ms->irq0, ms);
+	free_irq(ms->irq1, ms);
+
+	spi_unregister_master(master);
+	spi_master_put(master);
+	iounmap(ms->regs);
+}
+
+static struct of_device_id mpc52xx_spi_of_match[] __devinitdata = {
+	{ .compatible = "fsl,mpc5200-spi", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, mpc52xx_psc_spi_of_match);
+
+static struct of_platform_driver mpc52xx_spi_of_driver = {
+	.owner = THIS_MODULE,
+	.name = "mpc52xx-spi",
+	.match_table = mpc52xx_spi_of_match,
+	.probe = mpc52xx_spi_of_probe,
+	.remove = __exit_p(mpc52xx_spi_of_remove),
+};
+
+static int __init mpc52xx_spi_init(void)
+{
+	return of_register_platform_driver(&mpc52xx_spi_of_driver);
+}
+module_init(mpc52xx_spi_init);
+
+static void __exit mpc52xx_spi_exit(void)
+{
+	of_unregister_platform_driver(&mpc52xx_spi_of_driver);
+}
+module_exit(mpc52xx_spi_exit);
+
diff --git a/include/linux/spi/mpc52xx_spi.h b/include/linux/spi/mpc52xx_spi.h
new file mode 100644
index 0000000..d1004cf
--- /dev/null
+++ b/include/linux/spi/mpc52xx_spi.h
@@ -0,0 +1,10 @@
+
+#ifndef INCLUDE_MPC5200_SPI_H
+#define INCLUDE_MPC5200_SPI_H
+
+extern void mpc52xx_spi_set_premessage_hook(struct spi_master *master,
+					    void (*hook)(struct spi_message *m,
+							 void *context),
+					    void *hook_context);
+
+#endif


-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

Re: [PATCH v3 5/5] powerpc/mpc5200: Add mpc5200-spi (non-PSC) device driver

[Jon Smirl]

On 7/12/08, Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org> wrote:
> From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
>
>  Adds support for the dedicated SPI device on the Freescale MPC5200(b)
>  SoC.

Can you adjust the existing PSC based SPI driver to use this device
tree code? It will be confusing if there are two different ways to do
SPI on the mpc5200.

-- 
Jon Smirl
jonsmirl-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org

-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08

Re: [PATCH v3 3/5] of-bindings: Add binding documentation for SPI busses and devices

[Segher Boessenkool]

> From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
>
> Add documentation about how to describe SPI busses in the device tree.
>
> Signed-off-by: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>

Very nice!  I wish all bindings were like this (namely, not overly 
terse).

Acked-by: Segher Boessenkool <segher-XVmvHMARGAS8U2dJNN8I7kB+6BGkLq7r@public.gmane.org>


Segher


-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/

Re: [PATCH v3 5/5] powerpc/mpc5200: Add mpc5200-spi (non-PSC) device driver

[Grant Likely]

On Mon, Jul 14, 2008 at 09:21:08AM -0400, Jon Smirl wrote:
> On 7/12/08, Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org> wrote:
> > From: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
> >
> >  Adds support for the dedicated SPI device on the Freescale MPC5200(b)
> >  SoC.
> 
> Can you adjust the existing PSC based SPI driver to use this device
> tree code? It will be confusing if there are two different ways to do
> SPI on the mpc5200.

Yes, I'll do that and post the patch

g.

-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/