From: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
To: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org,
spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org,
lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org,
broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
rpurdie@rpsys
Cc: dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org,
Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>,
akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org,
alan-qBU/x9rampVanCEyBjwyrvXRex20P6io@public.gmane.org
Subject: [PATCH v7 00/12] tnetv107x ssp drivers
Date: Tue, 7 Dec 2010 09:51:50 -0500 [thread overview]
Message-ID: <1291733522-3626-1-git-send-email-cyril@ti.com> (raw)
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port
device. It has a built-in programmable execution engine that can be programmed
to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch series implements a driver stack that looks like the following:
+--------+
| eeprom | . . .
+--------+
+-----------+ +--------------+ +---------+
| regulator | . . . | i2c-gpio | | 1-wire | . . .
+-----------+ +--------------+ +---------+
+----------------------+ +--------------------------------+
| ssp-spi | | ssp-gpio |
+----------------------+ +--------------------------------+
+----------------------------------------------------------+
| ssp |
+----------------------------------------------------------+
Changes between v7 and v6 if this series:
- Workaround for iosel2 register not reading back set bits.
- Update backlight status once probe succeeds.
Changes between v6 and v5 of this series:
- Changed initcalls to module_init() across all drivers. This series now
uses a late_initcall() in the board to delay initialization of gpio and
regulator dependent devices.
Changes between v5 and v4 of this series:
- Moved drivers from misc/gpio/spi to mfd
- Removed implicit init-time iosel setup
- Minor cleanups in backlight driver
Changes between v3 and v4 of this series:
- Replaced polled wait for sequence termination with interrupt
- Improved locking within SSP driver
- Other minor cleanups
Changes between v2 and v3 of this series:
- Minor cleanups in Kconfig and Makefile ordering
Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device
registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups
Cyril Chemparathy (12):
misc: add driver for sequencer serial port
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
spi: add ti-ssp spi master driver
davinci: add spi devices on tnetv107x evm
regulator: add driver for tps6524x regulator
davinci: add tnetv107x evm regulators
gpio: add ti-ssp gpio driver
davinci: add tnetv107x evm ti-ssp gpio device
backlight: add support for tps6116x controller
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device
arch/arm/mach-davinci/board-tnetv107x-evm.c | 197 +++++++
arch/arm/mach-davinci/devices-tnetv107x.c | 25 +
arch/arm/mach-davinci/include/mach/tnetv107x.h | 2 +
arch/arm/mach-davinci/tnetv107x.c | 2 +-
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 1 +
drivers/gpio/ti-ssp-gpio.c | 206 +++++++
drivers/mfd/Kconfig | 11 +
drivers/mfd/Makefile | 1 +
drivers/mfd/ti-ssp.c | 476 ++++++++++++++++
drivers/regulator/Kconfig | 10 +
drivers/regulator/Makefile | 1 +
drivers/regulator/tps6524x-regulator.c | 692 ++++++++++++++++++++++++
drivers/spi/Kconfig | 10 +
drivers/spi/Makefile | 1 +
drivers/spi/ti-ssp-spi.c | 402 ++++++++++++++
drivers/video/backlight/Kconfig | 7 +
drivers/video/backlight/Makefile | 2 +-
drivers/video/backlight/tps6116x.c | 299 ++++++++++
include/linux/mfd/ti_ssp.h | 97 ++++
20 files changed, 2450 insertions(+), 2 deletions(-)
create mode 100644 drivers/gpio/ti-ssp-gpio.c
create mode 100644 drivers/mfd/ti-ssp.c
create mode 100644 drivers/regulator/tps6524x-regulator.c
create mode 100644 drivers/spi/ti-ssp-spi.c
create mode 100644 drivers/video/backlight/tps6116x.c
create mode 100644 include/linux/mfd/ti_ssp.h
------------------------------------------------------------------------------
What happens now with your Lotus Notes apps - do you make another costly
upgrade, or settle for being marooned without product support? Time to move
off Lotus Notes and onto the cloud with Force.com, apps are easier to build,
use, and manage than apps on traditional platforms. Sign up for the Lotus
Notes Migration Kit to learn more. http://p.sf.net/sfu/salesforce-d2d
next reply other threads:[~2010-12-07 14:51 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-07 14:51 Cyril Chemparathy [this message]
[not found] ` <1291733522-3626-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-07 14:51 ` [PATCH v7 01/12] misc: add driver for sequencer serial port Cyril Chemparathy
[not found] ` <1291733522-3626-2-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-11 0:13 ` Kevin Hilman
2010-12-07 14:51 ` [PATCH v7 02/12] davinci: add tnetv107x ssp platform device Cyril Chemparathy
2010-12-07 14:51 ` [PATCH v7 03/12] davinci: add ssp config for tnetv107x evm board Cyril Chemparathy
2010-12-07 14:51 ` [PATCH v7 04/12] spi: add ti-ssp spi master driver Cyril Chemparathy
[not found] ` <1291733522-3626-5-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-31 6:26 ` Grant Likely
2010-12-07 14:51 ` [PATCH v7 05/12] davinci: add spi devices on tnetv107x evm Cyril Chemparathy
2010-12-07 14:51 ` [PATCH v7 06/12] regulator: add driver for tps6524x regulator Cyril Chemparathy
[not found] ` <1291733522-3626-7-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-07 15:22 ` Mark Brown
[not found] ` <20101207152222.GD9689-HF5t3jzXg/6ND3a5+9QAFujbO/Zr0HzV@public.gmane.org>
2010-12-07 16:46 ` Cyril Chemparathy
2010-12-07 14:51 ` [PATCH v7 07/12] davinci: add tnetv107x evm regulators Cyril Chemparathy
2010-12-07 14:51 ` [PATCH v7 08/12] gpio: add ti-ssp gpio driver Cyril Chemparathy
[not found] ` <1291733522-3626-9-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-31 6:16 ` Grant Likely
2010-12-07 14:51 ` [PATCH v7 09/12] davinci: add tnetv107x evm ti-ssp gpio device Cyril Chemparathy
2010-12-07 14:52 ` [PATCH v7 10/12] backlight: add support for tps6116x controller Cyril Chemparathy
2010-12-07 14:52 ` [PATCH v7 11/12] davinci: add tnetv107x evm backlight device Cyril Chemparathy
[not found] ` <1291733522-3626-12-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-12-09 8:55 ` Nori, Sekhar
[not found] ` <B85A65D85D7EB246BE421B3FB0FBB5930247CD83E1@dbde02.ent.ti.com>
[not found] ` <B85A65D85D7EB246BE421B3FB0FBB5930247CD83E1-/tLxBxkBPtCIQmiDNMet8wC/G2K4zDHf@public.gmane.org>
2010-12-09 11:00 ` Nori, Sekhar
[not found] ` <B85A65D85D7EB246BE421B3FB0FBB5930247CD84F4@dbde02.ent.ti.com>
[not found] ` <B85A65D85D7EB246BE421B3FB0FBB5930247CD84F4-/tLxBxkBPtCIQmiDNMet8wC/G2K4zDHf@public.gmane.org>
2010-12-09 14:58 ` Cyril Chemparathy
[not found] ` <4D00EEA1.8070201-l0cyMroinI0@public.gmane.org>
2010-12-10 16:01 ` Nori, Sekhar
[not found] ` <B85A65D85D7EB246BE421B3FB0FBB5930247CD8CE8-/tLxBxkBPtCIQmiDNMet8wC/G2K4zDHf@public.gmane.org>
2010-12-10 16:56 ` Kevin Hilman
2010-12-07 14:52 ` [PATCH v7 12/12] davinci: add tnetv107x evm i2c eeprom device Cyril Chemparathy
2010-12-11 0:19 ` [PATCH v7 00/12] tnetv107x ssp drivers Kevin Hilman
[not found] ` <87r5dp6tzv.fsf-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org>
2010-12-11 12:42 ` Mark Brown
[not found] ` <20101211124242.GE9380-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
2010-12-30 21:05 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1291733522-3626-1-git-send-email-cyril@ti.com \
--to=cyril-l0cymroini0@public.gmane.org \
--cc=akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b@public.gmane.org \
--cc=alan-qBU/x9rampVanCEyBjwyrvXRex20P6io@public.gmane.org \
--cc=broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org \
--cc=dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
--cc=khilman-1D3HCaltpLuhEniVeURVKkEOCMrvLtNR@public.gmane.org \
--cc=lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org \
--cc=rpurdie@rpsys \
--cc=sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org \
--cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).