[PATCH v4 0/4] Add support for the Armada 3700 SPI controller

[PATCH v4 0/4] Add support for the Armada 3700 SPI controller

[Romain Perier]

The Marvell Armada 3700 SoC includes an SPI controller. This controller
supports up to 4 SPI slave devices, with dedicated chip selects, CPIO or
FIFO mode with DMA or CPU transfers and different SPI transfer modes
(Standard single, Dual or Quad).

This set of patches adds a basic support for the FIFO mode, (CPU-side
only, DMA not supported yet). It also adds the required definitions of
the spi nodes to the devicetree.

Romain Perier (4):
  spi: Add support for Armada 3700 SPI Controller
  spi: armada-3700: Add documentation for the Armada 3700 SPI Controller
  arm64: dts: marvell: Add definition of SPI controller for Armada 3700
  arm64: dts: marvell: Enable spi0 on the board Armada-3720-db

 .../devicetree/bindings/spi/spi-armada-3700.txt    |  25 +
 arch/arm64/boot/dts/marvell/armada-3720-db.dts     |  30 +
 arch/arm64/boot/dts/marvell/armada-37xx.dtsi       |  11 +
 drivers/spi/Kconfig                                |   7 +
 drivers/spi/Makefile                               |   1 +
 drivers/spi/spi-armada-3700.c                      | 923 +++++++++++++++++++++
 6 files changed, 997 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-armada-3700.txt
 create mode 100644 drivers/spi/spi-armada-3700.c

-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 1/4] spi: Add support for Armada 3700 SPI Controller

[Romain Perier]

Marvell Armada 3700 SoC comprises an SPI Controller. This Controller
supports up to 4 SPI slave devices, with dedicated chip selects,supports
SPI mode 0/1/2 and 3, CPIO or Fifo mode with DMA transfers and different
SPI transfer mode (Single, Dual or Quad).

This commit adds basic driver support for FIFO mode. In this mode,
dedicated registers are used to store the instruction, the address, the
read mode and the data. Write and Read FIFO are used to store the
outcoming or incoming data. The data FIFOs are accessible via DMA or by
the CPU. Only the CPU is supported for now.

Signed-off-by: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---

Changes in v4:
 - Added missing COMPILE_TEST in KConfig
 - Replaced the busy wait for loop by a single busy wait in spi_init()
 - Handle IRQ_NONE in the interrupt handler 
 - Assign pdev->id to master->cs_num directly (no conditionnal operator)
 - Moved clock gating into prepare/unprepare callbacks
 - Removed dev_info() in the end of the probe() function
 - Added flag to the spi master for single duplex transfers
 - Squashed patch 1/5 and 2/5 together: remove the non-fifo mode, just keep
   the more efficient mode
 - So removed the module parameter

Changes in v3:
 - Don't enable the fifo mode based on the compatible string, we introduce
   a module parameter "pio_mode". By default this option is set to zero, so
   the fifo mode is enabled. Pass pio_mode=1 to the driver enables the PIO
   mode.
 - Added tag "Tested-by" by Gregory
 - Fixed wrong variable passed as MODULE_DEVICE_TABLE
 - Added missing null terminated entry in a3700_spi_dt_ids 

Changes in v2:
 - Removed a3700_spi_bytelen_set from the setup function, it was accidentally
   let here and not required, as it is configured in the prepare callback now
   (defaults to 4 for fifo mode). It solves unrecognized spi-nor flash memory
   detection with jedec.

 drivers/spi/Kconfig           |   7 +
 drivers/spi/Makefile          |   1 +
 drivers/spi/spi-armada-3700.c | 923 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 931 insertions(+)
 create mode 100644 drivers/spi/spi-armada-3700.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index b799547..1faad2ce 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -67,6 +67,13 @@ config SPI_ATH79
 	  This enables support for the SPI controller present on the
 	  Atheros AR71XX/AR724X/AR913X SoCs.
 
+config SPI_ARMADA_3700
+	tristate "Marvell Armada 3700 SPI Controller"
+	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
+	help
+	  This enables support for the SPI controller present on the
+	  Marvell Armada 3700 SoCs.
+
 config SPI_ATMEL
 	tristate "Atmel SPI Controller"
 	depends on HAS_DMA
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index aa939d9..140ca45 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST)		+= spi-loopback-test.o
 
 # SPI master controller drivers (bus)
 obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
+obj-$(CONFIG_SPI_ARMADA_3700)		+= spi-armada-3700.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c
new file mode 100644
index 0000000..e89da0a
--- /dev/null
+++ b/drivers/spi/spi-armada-3700.c
@@ -0,0 +1,923 @@
+/*
+ * Marvell Armada-3700 SPI controller driver
+ *
+ * Copyright (C) 2016 Marvell Ltd.
+ *
+ * Author: Wilson Ding <dingwei-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
+ * Author: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/spi/spi.h>
+
+#define DRIVER_NAME			"armada_3700_spi"
+
+#define A3700_SPI_TIMEOUT		10
+
+/* SPI Register Offest */
+#define A3700_SPI_IF_CTRL_REG		0x00
+#define A3700_SPI_IF_CFG_REG		0x04
+#define A3700_SPI_DATA_OUT_REG		0x08
+#define A3700_SPI_DATA_IN_REG		0x0C
+#define A3700_SPI_IF_INST_REG		0x10
+#define A3700_SPI_IF_ADDR_REG		0x14
+#define A3700_SPI_IF_RMODE_REG		0x18
+#define A3700_SPI_IF_HDR_CNT_REG	0x1C
+#define A3700_SPI_IF_DIN_CNT_REG	0x20
+#define A3700_SPI_IF_TIME_REG		0x24
+#define A3700_SPI_INT_STAT_REG		0x28
+#define A3700_SPI_INT_MASK_REG		0x2C
+
+/* A3700_SPI_IF_CTRL_REG */
+#define A3700_SPI_EN			BIT(16)
+#define A3700_SPI_ADDR_NOT_CONFIG	BIT(12)
+#define A3700_SPI_WFIFO_OVERFLOW	BIT(11)
+#define A3700_SPI_WFIFO_UNDERFLOW	BIT(10)
+#define A3700_SPI_RFIFO_OVERFLOW	BIT(9)
+#define A3700_SPI_RFIFO_UNDERFLOW	BIT(8)
+#define A3700_SPI_WFIFO_FULL		BIT(7)
+#define A3700_SPI_WFIFO_EMPTY		BIT(6)
+#define A3700_SPI_RFIFO_FULL		BIT(5)
+#define A3700_SPI_RFIFO_EMPTY		BIT(4)
+#define A3700_SPI_WFIFO_RDY		BIT(3)
+#define A3700_SPI_RFIFO_RDY		BIT(2)
+#define A3700_SPI_XFER_RDY		BIT(1)
+#define A3700_SPI_XFER_DONE		BIT(0)
+
+/* A3700_SPI_IF_CFG_REG */
+#define A3700_SPI_WFIFO_THRS		BIT(28)
+#define A3700_SPI_RFIFO_THRS		BIT(24)
+#define A3700_SPI_AUTO_CS		BIT(20)
+#define A3700_SPI_DMA_RD_EN		BIT(18)
+#define A3700_SPI_FIFO_MODE		BIT(17)
+#define A3700_SPI_SRST			BIT(16)
+#define A3700_SPI_XFER_START		BIT(15)
+#define A3700_SPI_XFER_STOP		BIT(14)
+#define A3700_SPI_INST_PIN		BIT(13)
+#define A3700_SPI_ADDR_PIN		BIT(12)
+#define A3700_SPI_DATA_PIN1		BIT(11)
+#define A3700_SPI_DATA_PIN0		BIT(10)
+#define A3700_SPI_FIFO_FLUSH		BIT(9)
+#define A3700_SPI_RW_EN			BIT(8)
+#define A3700_SPI_CLK_POL		BIT(7)
+#define A3700_SPI_CLK_PHA		BIT(6)
+#define A3700_SPI_BYTE_LEN		BIT(5)
+#define A3700_SPI_CLK_PRESCALE		BIT(0)
+#define A3700_SPI_CLK_PRESCALE_MASK	(0x1f)
+
+#define A3700_SPI_WFIFO_THRS_BIT	28
+#define A3700_SPI_RFIFO_THRS_BIT	24
+#define A3700_SPI_FIFO_THRS_MASK	0x7
+
+#define A3700_SPI_DATA_PIN_MASK		0x3
+
+/* A3700_SPI_IF_HDR_CNT_REG */
+#define A3700_SPI_DUMMY_CNT_BIT		12
+#define A3700_SPI_DUMMY_CNT_MASK	0x7
+#define A3700_SPI_RMODE_CNT_BIT		8
+#define A3700_SPI_RMODE_CNT_MASK	0x3
+#define A3700_SPI_ADDR_CNT_BIT		4
+#define A3700_SPI_ADDR_CNT_MASK		0x7
+#define A3700_SPI_INSTR_CNT_BIT		0
+#define A3700_SPI_INSTR_CNT_MASK	0x3
+
+/* A3700_SPI_IF_TIME_REG */
+#define A3700_SPI_CLK_CAPT_EDGE		BIT(7)
+
+/* Flags and macros for struct a3700_spi */
+#define A3700_INSTR_CNT			1
+#define A3700_ADDR_CNT			3
+#define A3700_DUMMY_CNT			1
+
+struct a3700_spi {
+	struct spi_master *master;
+	void __iomem *base;
+	struct clk *clk;
+	unsigned int irq;
+	unsigned int flags;
+	bool xmit_data;
+	const u8 *tx_buf;
+	u8 *rx_buf;
+	size_t buf_len;
+	u8 byte_len;
+	u32 wait_mask;
+	struct completion done;
+	u32 addr_cnt;
+	u32 instr_cnt;
+	size_t hdr_cnt;
+};
+
+static u32 spireg_read(struct a3700_spi *a3700_spi, u32 offset)
+{
+	return readl(a3700_spi->base + offset);
+}
+
+static void spireg_write(struct a3700_spi *a3700_spi, u32 offset, u32 data)
+{
+	writel(data, a3700_spi->base + offset);
+}
+
+static void a3700_spi_auto_cs_unset(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~A3700_SPI_AUTO_CS;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_activate_cs(struct a3700_spi *a3700_spi, unsigned int cs)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	val |= (A3700_SPI_EN << cs);
+	spireg_write(a3700_spi, A3700_SPI_IF_CTRL_REG, val);
+}
+
+static void a3700_spi_deactivate_cs(struct a3700_spi *a3700_spi,
+				    unsigned int cs)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	val &= ~(A3700_SPI_EN << cs);
+	spireg_write(a3700_spi, A3700_SPI_IF_CTRL_REG, val);
+}
+
+static int a3700_spi_pin_mode_set(struct a3700_spi *a3700_spi,
+				  unsigned int pin_mode)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_INST_PIN | A3700_SPI_ADDR_PIN);
+	val &= ~(A3700_SPI_DATA_PIN0 | A3700_SPI_DATA_PIN1);
+
+	switch (pin_mode) {
+	case 1:
+		break;
+	case 2:
+		val |= A3700_SPI_DATA_PIN0;
+		break;
+	case 4:
+		val |= A3700_SPI_DATA_PIN1;
+		break;
+	default:
+		dev_err(&a3700_spi->master->dev, "wrong pin mode %u", pin_mode);
+		return -EINVAL;
+	}
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	return 0;
+}
+
+static void a3700_spi_fifo_mode_set(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_FIFO_MODE;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_mode_set(struct a3700_spi *a3700_spi,
+			       unsigned int mode_bits)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+
+	if (mode_bits & SPI_CPOL)
+		val |= A3700_SPI_CLK_POL;
+	else
+		val &= ~A3700_SPI_CLK_POL;
+
+	if (mode_bits & SPI_CPHA)
+		val |= A3700_SPI_CLK_PHA;
+	else
+		val &= ~A3700_SPI_CLK_PHA;
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_clock_set(struct a3700_spi *a3700_spi,
+				unsigned int speed_hz, u16 mode)
+{
+	u32 val;
+	u32 prescale;
+
+	prescale = DIV_ROUND_UP(clk_get_rate(a3700_spi->clk), speed_hz);
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val = val & ~A3700_SPI_CLK_PRESCALE_MASK;
+
+	val = val | (prescale & A3700_SPI_CLK_PRESCALE_MASK);
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	if (prescale <= 2) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_TIME_REG);
+		val |= A3700_SPI_CLK_CAPT_EDGE;
+		spireg_write(a3700_spi, A3700_SPI_IF_TIME_REG, val);
+	}
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_CLK_POL | A3700_SPI_CLK_PHA);
+
+	if (mode & SPI_CPOL)
+		val |= A3700_SPI_CLK_POL;
+
+	if (mode & SPI_CPHA)
+		val |= A3700_SPI_CLK_PHA;
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_bytelen_set(struct a3700_spi *a3700_spi, unsigned int len)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	if (len == 4)
+		val |= A3700_SPI_BYTE_LEN;
+	else
+		val &= ~A3700_SPI_BYTE_LEN;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	a3700_spi->byte_len = len;
+}
+
+static int a3700_spi_fifo_flush(struct a3700_spi *a3700_spi)
+{
+	int timeout = A3700_SPI_TIMEOUT;
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_FIFO_FLUSH;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_FIFO_FLUSH))
+			return 0;
+		udelay(1);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int a3700_spi_init(struct a3700_spi *a3700_spi)
+{
+	struct spi_master *master = a3700_spi->master;
+	u32 val;
+	int i, ret = 0;
+
+	/* Reset SPI unit */
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_SRST;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	udelay(A3700_SPI_TIMEOUT);
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~A3700_SPI_SRST;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	/* Disable AUTO_CS and deactivate all chip-selects */
+	a3700_spi_auto_cs_unset(a3700_spi);
+	for (i = 0; i < master->num_chipselect; i++)
+		a3700_spi_deactivate_cs(a3700_spi, i);
+
+	/* Enable FIFO mode */
+	a3700_spi_fifo_mode_set(a3700_spi);
+
+	/* Set SPI mode */
+	a3700_spi_mode_set(a3700_spi, master->mode_bits);
+
+	/* Reset counters */
+	spireg_write(a3700_spi, A3700_SPI_IF_HDR_CNT_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_DIN_CNT_REG, 0);
+
+	/* Mask the interrupts and clear cause bits */
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, ~0U);
+
+	return ret;
+}
+
+static irqreturn_t a3700_spi_interrupt(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct a3700_spi *a3700_spi;
+	u32 cause;
+
+	a3700_spi = spi_master_get_devdata(master);
+
+	/* Get interrupt causes */
+	cause = spireg_read(a3700_spi, A3700_SPI_INT_STAT_REG);
+
+	if (!cause || !(a3700_spi->wait_mask & cause))
+		return IRQ_NONE;
+
+	/* mask and acknowledge the SPI interrupts */
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, cause);
+
+	/* Wake up the transfer */
+	if (a3700_spi->wait_mask & cause)
+		complete(&a3700_spi->done);
+
+	return IRQ_HANDLED;
+}
+
+static bool a3700_spi_wait_completion(struct spi_device *spi)
+{
+	struct a3700_spi *a3700_spi;
+	unsigned int timeout;
+	unsigned int ctrl_reg;
+	unsigned long timeout_jiffies;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+
+	/* SPI interrupt is edge-triggered, which means an interrupt will
+	 * be generated only when detecting a specific status bit changed
+	 * from '0' to '1'. So when we start waiting for a interrupt, we
+	 * need to check status bit in control reg first, if it is already 1,
+	 * then we do not need to wait for interrupt
+	 */
+	ctrl_reg = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	if (a3700_spi->wait_mask & ctrl_reg)
+		return true;
+
+	reinit_completion(&a3700_spi->done);
+
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG,
+		     a3700_spi->wait_mask);
+
+	timeout_jiffies = msecs_to_jiffies(A3700_SPI_TIMEOUT);
+	timeout = wait_for_completion_timeout(&a3700_spi->done,
+					      timeout_jiffies);
+
+	a3700_spi->wait_mask = 0;
+
+	if (timeout)
+		return true;
+
+	/* there might be the case that right after we checked the
+	 * status bits in this routine and before start to wait for
+	 * interrupt by wait_for_completion_timeout, the interrupt
+	 * happens, to avoid missing it we need to double check
+	 * status bits in control reg, if it is already 1, then
+	 * consider that we have the interrupt successfully and
+	 * return true.
+	 */
+	ctrl_reg = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	if (a3700_spi->wait_mask & ctrl_reg)
+		return true;
+
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+
+	return true;
+}
+
+static bool a3700_spi_transfer_wait(struct spi_device *spi,
+				    unsigned int bit_mask)
+{
+	struct a3700_spi *a3700_spi;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+	a3700_spi->wait_mask = bit_mask;
+
+	return a3700_spi_wait_completion(spi);
+}
+
+static void a3700_spi_fifo_thres_set(struct a3700_spi *a3700_spi,
+				     unsigned int bytes)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_FIFO_THRS_MASK << A3700_SPI_RFIFO_THRS_BIT);
+	val |= (bytes - 1) << A3700_SPI_RFIFO_THRS_BIT;
+	val &= ~(A3700_SPI_FIFO_THRS_MASK << A3700_SPI_WFIFO_THRS_BIT);
+	val |= (7 - bytes) << A3700_SPI_WFIFO_THRS_BIT;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_transfer_setup(struct spi_device *spi,
+				    struct spi_transfer *xfer)
+{
+	struct a3700_spi *a3700_spi;
+	unsigned int byte_len;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+
+	a3700_spi_clock_set(a3700_spi, xfer->speed_hz, spi->mode);
+
+	byte_len = xfer->bits_per_word >> 3;
+
+	a3700_spi_fifo_thres_set(a3700_spi, byte_len);
+}
+
+static void a3700_spi_set_cs(struct spi_device *spi, bool enable)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(spi->master);
+
+	if (!enable)
+		a3700_spi_activate_cs(a3700_spi, spi->chip_select);
+	else
+		a3700_spi_deactivate_cs(a3700_spi, spi->chip_select);
+}
+
+static void a3700_spi_header_set(struct a3700_spi *a3700_spi)
+{
+	u32 instr_cnt = 0, addr_cnt = 0, dummy_cnt = 0;
+	u32 val = 0;
+
+	/* Clear the header registers */
+	spireg_write(a3700_spi, A3700_SPI_IF_INST_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_ADDR_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_RMODE_REG, 0);
+
+	/* Set header counters */
+	if (a3700_spi->tx_buf) {
+		if (a3700_spi->buf_len <= a3700_spi->instr_cnt) {
+			instr_cnt = a3700_spi->buf_len;
+		} else if (a3700_spi->buf_len <= (a3700_spi->instr_cnt +
+						  a3700_spi->addr_cnt)) {
+			instr_cnt = a3700_spi->instr_cnt;
+			addr_cnt = a3700_spi->buf_len - instr_cnt;
+		} else if (a3700_spi->buf_len <= a3700_spi->hdr_cnt) {
+			instr_cnt = a3700_spi->instr_cnt;
+			addr_cnt = a3700_spi->addr_cnt;
+			/* Need to handle the normal write case with 1 byte
+			 * data
+			 */
+			if (!a3700_spi->tx_buf[instr_cnt + addr_cnt])
+				dummy_cnt = a3700_spi->buf_len - instr_cnt -
+					    addr_cnt;
+		}
+		val |= ((instr_cnt & A3700_SPI_INSTR_CNT_MASK)
+			<< A3700_SPI_INSTR_CNT_BIT);
+		val |= ((addr_cnt & A3700_SPI_ADDR_CNT_MASK)
+			<< A3700_SPI_ADDR_CNT_BIT);
+		val |= ((dummy_cnt & A3700_SPI_DUMMY_CNT_MASK)
+			<< A3700_SPI_DUMMY_CNT_BIT);
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_HDR_CNT_REG, val);
+
+	/* Update the buffer length to be transferred */
+	a3700_spi->buf_len -= (instr_cnt + addr_cnt + dummy_cnt);
+
+	/* Set Instruction */
+	val = 0;
+	while (instr_cnt--) {
+		val = (val << 8) | a3700_spi->tx_buf[0];
+		a3700_spi->tx_buf++;
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_INST_REG, val);
+
+	/* Set Address */
+	val = 0;
+	while (addr_cnt--) {
+		val = (val << 8) | a3700_spi->tx_buf[0];
+		a3700_spi->tx_buf++;
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_ADDR_REG, val);
+}
+
+static int a3700_is_wfifo_full(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	return (val & A3700_SPI_WFIFO_FULL);
+}
+
+static int a3700_spi_fifo_write(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+	int i = 0;
+
+	while (!a3700_is_wfifo_full(a3700_spi) && a3700_spi->buf_len) {
+		val = 0;
+		if (a3700_spi->buf_len >= 4) {
+			val = cpu_to_le32(*(u32 *)a3700_spi->tx_buf);
+			spireg_write(a3700_spi, A3700_SPI_DATA_OUT_REG, val);
+
+			a3700_spi->buf_len -= 4;
+			a3700_spi->tx_buf += 4;
+		} else {
+			/*
+			 * If the remained buffer length is less than 4-bytes,
+			 * we should pad the write buffer with all ones. So that
+			 * it avoids overwrite the unexpected bytes following
+			 * the last one.
+			 */
+			val = GENMASK(31, 0);
+			while (a3700_spi->buf_len) {
+				val &= ~(0xff << (8 * i));
+				val |= *a3700_spi->tx_buf++ << (8 * i);
+				i++;
+				a3700_spi->buf_len--;
+
+				spireg_write(a3700_spi, A3700_SPI_DATA_OUT_REG,
+					     val);
+			}
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int a3700_is_rfifo_empty(struct a3700_spi *a3700_spi)
+{
+	u32 val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+
+	return (val & A3700_SPI_RFIFO_EMPTY);
+}
+
+static int a3700_spi_fifo_read(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	while (!a3700_is_rfifo_empty(a3700_spi) && a3700_spi->buf_len) {
+		val = spireg_read(a3700_spi, A3700_SPI_DATA_IN_REG);
+		if (a3700_spi->buf_len >= 4) {
+			u32 data = le32_to_cpu(val);
+			memcpy(a3700_spi->rx_buf, &data, 4);
+
+			a3700_spi->buf_len -= 4;
+			a3700_spi->rx_buf += 4;
+		} else {
+			/*
+			 * When remain bytes is not larger than 4, we should
+			 * avoid memory overwriting and just write the left rx
+			 * buffer bytes.
+			 */
+			while (a3700_spi->buf_len) {
+				*a3700_spi->rx_buf = val & 0xff;
+				val >>= 8;
+
+				a3700_spi->buf_len--;
+				a3700_spi->rx_buf++;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static void a3700_spi_transfer_abort_fifo(struct a3700_spi *a3700_spi)
+{
+	int timeout = A3700_SPI_TIMEOUT;
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_XFER_START))
+			break;
+		udelay(1);
+	}
+
+	a3700_spi_fifo_flush(a3700_spi);
+
+	val &= ~A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static int a3700_spi_prepare_message(struct spi_master *master,
+				     struct spi_message *message)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+	struct spi_device *spi = message->spi;
+	int ret;
+
+	ret = clk_enable(a3700_spi->clk);
+	if (ret) {
+		dev_err(&spi->dev, "failed to enable clk with error %d\n", ret);
+		return ret;
+	}
+
+	/* Flush the FIFOs */
+	ret = a3700_spi_fifo_flush(a3700_spi);
+	if (ret)
+		return ret;
+
+	a3700_spi_bytelen_set(a3700_spi, 4);
+
+	return 0;
+}
+
+static int a3700_spi_transfer_one(struct spi_master *master,
+				  struct spi_device *spi,
+				  struct spi_transfer *xfer)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+	int ret = 0, timeout = A3700_SPI_TIMEOUT;
+	unsigned int nbits = 0;
+	u32 val;
+
+	a3700_spi_transfer_setup(spi, xfer);
+
+	a3700_spi->tx_buf  = xfer->tx_buf;
+	a3700_spi->rx_buf  = xfer->rx_buf;
+	a3700_spi->buf_len = xfer->len;
+
+	/* SPI transfer headers */
+	a3700_spi_header_set(a3700_spi);
+
+	if (xfer->tx_buf)
+		nbits = xfer->tx_nbits;
+	else if (xfer->rx_buf)
+		nbits = xfer->rx_nbits;
+
+	a3700_spi_pin_mode_set(a3700_spi, nbits);
+
+	if (xfer->rx_buf) {
+		/* Set read data length */
+		spireg_write(a3700_spi, A3700_SPI_IF_DIN_CNT_REG,
+			     a3700_spi->buf_len);
+		/* Start READ transfer */
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val &= ~A3700_SPI_RW_EN;
+		val |= A3700_SPI_XFER_START;
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	} else if (xfer->tx_buf) {
+		/* Start Write transfer */
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val |= (A3700_SPI_XFER_START | A3700_SPI_RW_EN);
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+		/*
+		 * If there are data to be written to the SPI device, xmit_data
+		 * flag is set true; otherwise the instruction in SPI_INSTR does
+		 * not require data to be written to the SPI device, then
+		 * xmit_data flag is set false.
+		 */
+		a3700_spi->xmit_data = (a3700_spi->buf_len != 0);
+	}
+
+	while (a3700_spi->buf_len) {
+		if (a3700_spi->tx_buf) {
+			/* Wait wfifo ready */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_WFIFO_RDY)) {
+				dev_err(&spi->dev,
+					"wait wfifo ready timed out\n");
+				ret = -ETIMEDOUT;
+				goto error;
+			}
+			/* Fill up the wfifo */
+			ret = a3700_spi_fifo_write(a3700_spi);
+			if (ret)
+				goto error;
+		} else if (a3700_spi->rx_buf) {
+			/* Wait rfifo ready */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_RFIFO_RDY)) {
+				dev_err(&spi->dev,
+					"wait rfifo ready timed out\n");
+				ret = -ETIMEDOUT;
+				goto error;
+			}
+			/* Drain out the rfifo */
+			ret = a3700_spi_fifo_read(a3700_spi);
+			if (ret)
+				goto error;
+		}
+	}
+
+	/*
+	 * Stop a write transfer in fifo mode:
+	 *	- wait all the bytes in wfifo to be shifted out
+	 *	 - set XFER_STOP bit
+	 *	- wait XFER_START bit clear
+	 *	- clear XFER_STOP bit
+	 * Stop a read transfer in fifo mode:
+	 *	- the hardware is to reset the XFER_START bit
+	 *	   after the number of bytes indicated in DIN_CNT
+	 *	   register
+	 *	- just wait XFER_START bit clear
+	 */
+	if (a3700_spi->tx_buf) {
+		if (a3700_spi->xmit_data) {
+			/*
+			 * If there are data written to the SPI device, wait
+			 * until SPI_WFIFO_EMPTY is 1 to wait for all data to
+			 * transfer out of write FIFO.
+			 */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_WFIFO_EMPTY)) {
+				dev_err(&spi->dev, "wait wfifo empty timed out\n");
+				return -ETIMEDOUT;
+			}
+		} else {
+			/*
+			 * If the instruction in SPI_INSTR does not require data
+			 * to be written to the SPI device, wait until SPI_RDY
+			 * is 1 for the SPI interface to be in idle.
+			 */
+			if (!a3700_spi_transfer_wait(spi, A3700_SPI_XFER_RDY)) {
+				dev_err(&spi->dev, "wait xfer ready timed out\n");
+				return -ETIMEDOUT;
+			}
+		}
+
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val |= A3700_SPI_XFER_STOP;
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	}
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_XFER_START))
+			break;
+		udelay(1);
+	}
+
+	if (timeout == 0) {
+		dev_err(&spi->dev, "wait transfer start clear timed out\n");
+		ret = -ETIMEDOUT;
+		goto error;
+	}
+
+	val &= ~A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	goto out;
+
+error:
+	a3700_spi_transfer_abort_fifo(a3700_spi);
+out:
+	spi_finalize_current_transfer(master);
+
+	return ret;
+}
+
+static int a3700_spi_unprepare_message(struct spi_master *master,
+				       struct spi_message *message)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+
+	clk_disable(a3700_spi->clk);
+
+	return 0;
+}
+
+static const struct of_device_id a3700_spi_dt_ids[] = {
+	{ .compatible = "marvell,armada-3700-spi", .data = NULL },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, a3700_spi_dt_ids);
+
+static int a3700_spi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *of_node = dev->of_node;
+	struct resource *res;
+	struct spi_master *master;
+	struct a3700_spi *spi;
+	u32 num_cs = 0;
+	int ret = 0;
+
+	master = spi_alloc_master(dev, sizeof(*spi));
+	if (!master) {
+		dev_err(dev, "master allocation failed\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (of_property_read_u32(of_node, "num-cs", &num_cs)) {
+		dev_err(dev, "could not find num-cs\n");
+		ret = -ENXIO;
+		goto error;
+	}
+
+	master->bus_num = pdev->id;
+	master->dev.of_node = of_node;
+	master->mode_bits = SPI_MODE_3;
+	master->num_chipselect = num_cs;
+	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(32);
+	master->prepare_message =  a3700_spi_prepare_message;
+	master->transfer_one = a3700_spi_transfer_one;
+	master->unprepare_message = a3700_spi_unprepare_message;
+	master->set_cs = a3700_spi_set_cs;
+	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->mode_bits |= (SPI_RX_DUAL | SPI_RX_DUAL |
+			      SPI_RX_QUAD | SPI_TX_QUAD);
+
+	platform_set_drvdata(pdev, master);
+
+	spi = spi_master_get_devdata(master);
+	memset(spi, 0, sizeof(struct a3700_spi));
+
+	spi->master = master;
+	spi->instr_cnt = A3700_INSTR_CNT;
+	spi->addr_cnt = A3700_ADDR_CNT;
+	spi->hdr_cnt = A3700_INSTR_CNT + A3700_ADDR_CNT +
+		       A3700_DUMMY_CNT;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	spi->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(spi->base)) {
+		ret = PTR_ERR(spi->base);
+		goto error;
+	}
+
+	spi->irq = platform_get_irq(pdev, 0);
+	if (spi->irq < 0) {
+		dev_err(dev, "could not get irq: %d\n", spi->irq);
+		ret = -ENXIO;
+		goto error;
+	}
+
+	init_completion(&spi->done);
+
+	spi->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(spi->clk)) {
+		dev_err(dev, "could not find clk: %ld\n", PTR_ERR(spi->clk));
+		goto error;
+	}
+
+	ret = clk_prepare(spi->clk);
+	if (ret) {
+		dev_err(dev, "could not prepare clk: %d\n", ret);
+		goto error;
+	}
+
+	ret = a3700_spi_init(spi);
+	if (ret)
+		goto error_clk;
+
+	ret = devm_request_irq(dev, spi->irq, a3700_spi_interrupt, 0,
+			       dev_name(dev), master);
+	if (ret) {
+		dev_err(dev, "could not request IRQ: %d\n", ret);
+		goto error_clk;
+	}
+
+	ret = devm_spi_register_master(dev, master);
+	if (ret) {
+		dev_err(dev, "Failed to register master\n");
+		goto error_clk;
+	}
+
+	return 0;
+
+error_clk:
+	clk_disable_unprepare(spi->clk);
+error:
+	spi_master_put(master);
+out:
+	return ret;
+}
+
+static int a3700_spi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct a3700_spi *spi = spi_master_get_devdata(master);
+
+	clk_unprepare(spi->clk);
+	spi_master_put(master);
+
+	return 0;
+}
+
+static struct platform_driver a3700_spi_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(a3700_spi_dt_ids),
+	},
+	.probe		= a3700_spi_probe,
+	.remove		= a3700_spi_remove,
+};
+
+module_platform_driver(a3700_spi_driver);
+
+MODULE_DESCRIPTION("Armada-3700 SPI driver");
+MODULE_AUTHOR("Wilson Ding <dingwei-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Applied "spi: Add support for Armada 3700 SPI Controller" to the spi tree

[Mark Brown]

The patch

   spi: Add support for Armada 3700 SPI Controller

has been applied to the spi tree at

   git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git 

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.  

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

>From 5762ab71eb24a8393a167361510d7ca5e18c99f9 Mon Sep 17 00:00:00 2001
From: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Date: Thu, 8 Dec 2016 15:58:44 +0100
Subject: [PATCH] spi: Add support for Armada 3700 SPI Controller

Marvell Armada 3700 SoC comprises an SPI Controller. This Controller
supports up to 4 SPI slave devices, with dedicated chip selects,supports
SPI mode 0/1/2 and 3, CPIO or Fifo mode with DMA transfers and different
SPI transfer mode (Single, Dual or Quad).

This commit adds basic driver support for FIFO mode. In this mode,
dedicated registers are used to store the instruction, the address, the
read mode and the data. Write and Read FIFO are used to store the
outcoming or incoming data. The data FIFOs are accessible via DMA or by
the CPU. Only the CPU is supported for now.

Signed-off-by: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Signed-off-by: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/Kconfig           |   7 +
 drivers/spi/Makefile          |   1 +
 drivers/spi/spi-armada-3700.c | 923 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 931 insertions(+)
 create mode 100644 drivers/spi/spi-armada-3700.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index b7995474148c..1faad2ce4b4b 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -67,6 +67,13 @@ config SPI_ATH79
 	  This enables support for the SPI controller present on the
 	  Atheros AR71XX/AR724X/AR913X SoCs.
 
+config SPI_ARMADA_3700
+	tristate "Marvell Armada 3700 SPI Controller"
+	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
+	help
+	  This enables support for the SPI controller present on the
+	  Marvell Armada 3700 SoCs.
+
 config SPI_ATMEL
 	tristate "Atmel SPI Controller"
 	depends on HAS_DMA
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index aa939d955521..140ca45aa9d2 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST)		+= spi-loopback-test.o
 
 # SPI master controller drivers (bus)
 obj-$(CONFIG_SPI_ALTERA)		+= spi-altera.o
+obj-$(CONFIG_SPI_ARMADA_3700)		+= spi-armada-3700.o
 obj-$(CONFIG_SPI_ATMEL)			+= spi-atmel.o
 obj-$(CONFIG_SPI_ATH79)			+= spi-ath79.o
 obj-$(CONFIG_SPI_AU1550)		+= spi-au1550.o
diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c
new file mode 100644
index 000000000000..e89da0af45d2
--- /dev/null
+++ b/drivers/spi/spi-armada-3700.c
@@ -0,0 +1,923 @@
+/*
+ * Marvell Armada-3700 SPI controller driver
+ *
+ * Copyright (C) 2016 Marvell Ltd.
+ *
+ * Author: Wilson Ding <dingwei-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
+ * Author: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/spi/spi.h>
+
+#define DRIVER_NAME			"armada_3700_spi"
+
+#define A3700_SPI_TIMEOUT		10
+
+/* SPI Register Offest */
+#define A3700_SPI_IF_CTRL_REG		0x00
+#define A3700_SPI_IF_CFG_REG		0x04
+#define A3700_SPI_DATA_OUT_REG		0x08
+#define A3700_SPI_DATA_IN_REG		0x0C
+#define A3700_SPI_IF_INST_REG		0x10
+#define A3700_SPI_IF_ADDR_REG		0x14
+#define A3700_SPI_IF_RMODE_REG		0x18
+#define A3700_SPI_IF_HDR_CNT_REG	0x1C
+#define A3700_SPI_IF_DIN_CNT_REG	0x20
+#define A3700_SPI_IF_TIME_REG		0x24
+#define A3700_SPI_INT_STAT_REG		0x28
+#define A3700_SPI_INT_MASK_REG		0x2C
+
+/* A3700_SPI_IF_CTRL_REG */
+#define A3700_SPI_EN			BIT(16)
+#define A3700_SPI_ADDR_NOT_CONFIG	BIT(12)
+#define A3700_SPI_WFIFO_OVERFLOW	BIT(11)
+#define A3700_SPI_WFIFO_UNDERFLOW	BIT(10)
+#define A3700_SPI_RFIFO_OVERFLOW	BIT(9)
+#define A3700_SPI_RFIFO_UNDERFLOW	BIT(8)
+#define A3700_SPI_WFIFO_FULL		BIT(7)
+#define A3700_SPI_WFIFO_EMPTY		BIT(6)
+#define A3700_SPI_RFIFO_FULL		BIT(5)
+#define A3700_SPI_RFIFO_EMPTY		BIT(4)
+#define A3700_SPI_WFIFO_RDY		BIT(3)
+#define A3700_SPI_RFIFO_RDY		BIT(2)
+#define A3700_SPI_XFER_RDY		BIT(1)
+#define A3700_SPI_XFER_DONE		BIT(0)
+
+/* A3700_SPI_IF_CFG_REG */
+#define A3700_SPI_WFIFO_THRS		BIT(28)
+#define A3700_SPI_RFIFO_THRS		BIT(24)
+#define A3700_SPI_AUTO_CS		BIT(20)
+#define A3700_SPI_DMA_RD_EN		BIT(18)
+#define A3700_SPI_FIFO_MODE		BIT(17)
+#define A3700_SPI_SRST			BIT(16)
+#define A3700_SPI_XFER_START		BIT(15)
+#define A3700_SPI_XFER_STOP		BIT(14)
+#define A3700_SPI_INST_PIN		BIT(13)
+#define A3700_SPI_ADDR_PIN		BIT(12)
+#define A3700_SPI_DATA_PIN1		BIT(11)
+#define A3700_SPI_DATA_PIN0		BIT(10)
+#define A3700_SPI_FIFO_FLUSH		BIT(9)
+#define A3700_SPI_RW_EN			BIT(8)
+#define A3700_SPI_CLK_POL		BIT(7)
+#define A3700_SPI_CLK_PHA		BIT(6)
+#define A3700_SPI_BYTE_LEN		BIT(5)
+#define A3700_SPI_CLK_PRESCALE		BIT(0)
+#define A3700_SPI_CLK_PRESCALE_MASK	(0x1f)
+
+#define A3700_SPI_WFIFO_THRS_BIT	28
+#define A3700_SPI_RFIFO_THRS_BIT	24
+#define A3700_SPI_FIFO_THRS_MASK	0x7
+
+#define A3700_SPI_DATA_PIN_MASK		0x3
+
+/* A3700_SPI_IF_HDR_CNT_REG */
+#define A3700_SPI_DUMMY_CNT_BIT		12
+#define A3700_SPI_DUMMY_CNT_MASK	0x7
+#define A3700_SPI_RMODE_CNT_BIT		8
+#define A3700_SPI_RMODE_CNT_MASK	0x3
+#define A3700_SPI_ADDR_CNT_BIT		4
+#define A3700_SPI_ADDR_CNT_MASK		0x7
+#define A3700_SPI_INSTR_CNT_BIT		0
+#define A3700_SPI_INSTR_CNT_MASK	0x3
+
+/* A3700_SPI_IF_TIME_REG */
+#define A3700_SPI_CLK_CAPT_EDGE		BIT(7)
+
+/* Flags and macros for struct a3700_spi */
+#define A3700_INSTR_CNT			1
+#define A3700_ADDR_CNT			3
+#define A3700_DUMMY_CNT			1
+
+struct a3700_spi {
+	struct spi_master *master;
+	void __iomem *base;
+	struct clk *clk;
+	unsigned int irq;
+	unsigned int flags;
+	bool xmit_data;
+	const u8 *tx_buf;
+	u8 *rx_buf;
+	size_t buf_len;
+	u8 byte_len;
+	u32 wait_mask;
+	struct completion done;
+	u32 addr_cnt;
+	u32 instr_cnt;
+	size_t hdr_cnt;
+};
+
+static u32 spireg_read(struct a3700_spi *a3700_spi, u32 offset)
+{
+	return readl(a3700_spi->base + offset);
+}
+
+static void spireg_write(struct a3700_spi *a3700_spi, u32 offset, u32 data)
+{
+	writel(data, a3700_spi->base + offset);
+}
+
+static void a3700_spi_auto_cs_unset(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~A3700_SPI_AUTO_CS;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_activate_cs(struct a3700_spi *a3700_spi, unsigned int cs)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	val |= (A3700_SPI_EN << cs);
+	spireg_write(a3700_spi, A3700_SPI_IF_CTRL_REG, val);
+}
+
+static void a3700_spi_deactivate_cs(struct a3700_spi *a3700_spi,
+				    unsigned int cs)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	val &= ~(A3700_SPI_EN << cs);
+	spireg_write(a3700_spi, A3700_SPI_IF_CTRL_REG, val);
+}
+
+static int a3700_spi_pin_mode_set(struct a3700_spi *a3700_spi,
+				  unsigned int pin_mode)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_INST_PIN | A3700_SPI_ADDR_PIN);
+	val &= ~(A3700_SPI_DATA_PIN0 | A3700_SPI_DATA_PIN1);
+
+	switch (pin_mode) {
+	case 1:
+		break;
+	case 2:
+		val |= A3700_SPI_DATA_PIN0;
+		break;
+	case 4:
+		val |= A3700_SPI_DATA_PIN1;
+		break;
+	default:
+		dev_err(&a3700_spi->master->dev, "wrong pin mode %u", pin_mode);
+		return -EINVAL;
+	}
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	return 0;
+}
+
+static void a3700_spi_fifo_mode_set(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_FIFO_MODE;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_mode_set(struct a3700_spi *a3700_spi,
+			       unsigned int mode_bits)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+
+	if (mode_bits & SPI_CPOL)
+		val |= A3700_SPI_CLK_POL;
+	else
+		val &= ~A3700_SPI_CLK_POL;
+
+	if (mode_bits & SPI_CPHA)
+		val |= A3700_SPI_CLK_PHA;
+	else
+		val &= ~A3700_SPI_CLK_PHA;
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_clock_set(struct a3700_spi *a3700_spi,
+				unsigned int speed_hz, u16 mode)
+{
+	u32 val;
+	u32 prescale;
+
+	prescale = DIV_ROUND_UP(clk_get_rate(a3700_spi->clk), speed_hz);
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val = val & ~A3700_SPI_CLK_PRESCALE_MASK;
+
+	val = val | (prescale & A3700_SPI_CLK_PRESCALE_MASK);
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	if (prescale <= 2) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_TIME_REG);
+		val |= A3700_SPI_CLK_CAPT_EDGE;
+		spireg_write(a3700_spi, A3700_SPI_IF_TIME_REG, val);
+	}
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_CLK_POL | A3700_SPI_CLK_PHA);
+
+	if (mode & SPI_CPOL)
+		val |= A3700_SPI_CLK_POL;
+
+	if (mode & SPI_CPHA)
+		val |= A3700_SPI_CLK_PHA;
+
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_bytelen_set(struct a3700_spi *a3700_spi, unsigned int len)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	if (len == 4)
+		val |= A3700_SPI_BYTE_LEN;
+	else
+		val &= ~A3700_SPI_BYTE_LEN;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	a3700_spi->byte_len = len;
+}
+
+static int a3700_spi_fifo_flush(struct a3700_spi *a3700_spi)
+{
+	int timeout = A3700_SPI_TIMEOUT;
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_FIFO_FLUSH;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_FIFO_FLUSH))
+			return 0;
+		udelay(1);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int a3700_spi_init(struct a3700_spi *a3700_spi)
+{
+	struct spi_master *master = a3700_spi->master;
+	u32 val;
+	int i, ret = 0;
+
+	/* Reset SPI unit */
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_SRST;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	udelay(A3700_SPI_TIMEOUT);
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~A3700_SPI_SRST;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	/* Disable AUTO_CS and deactivate all chip-selects */
+	a3700_spi_auto_cs_unset(a3700_spi);
+	for (i = 0; i < master->num_chipselect; i++)
+		a3700_spi_deactivate_cs(a3700_spi, i);
+
+	/* Enable FIFO mode */
+	a3700_spi_fifo_mode_set(a3700_spi);
+
+	/* Set SPI mode */
+	a3700_spi_mode_set(a3700_spi, master->mode_bits);
+
+	/* Reset counters */
+	spireg_write(a3700_spi, A3700_SPI_IF_HDR_CNT_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_DIN_CNT_REG, 0);
+
+	/* Mask the interrupts and clear cause bits */
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, ~0U);
+
+	return ret;
+}
+
+static irqreturn_t a3700_spi_interrupt(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct a3700_spi *a3700_spi;
+	u32 cause;
+
+	a3700_spi = spi_master_get_devdata(master);
+
+	/* Get interrupt causes */
+	cause = spireg_read(a3700_spi, A3700_SPI_INT_STAT_REG);
+
+	if (!cause || !(a3700_spi->wait_mask & cause))
+		return IRQ_NONE;
+
+	/* mask and acknowledge the SPI interrupts */
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, cause);
+
+	/* Wake up the transfer */
+	if (a3700_spi->wait_mask & cause)
+		complete(&a3700_spi->done);
+
+	return IRQ_HANDLED;
+}
+
+static bool a3700_spi_wait_completion(struct spi_device *spi)
+{
+	struct a3700_spi *a3700_spi;
+	unsigned int timeout;
+	unsigned int ctrl_reg;
+	unsigned long timeout_jiffies;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+
+	/* SPI interrupt is edge-triggered, which means an interrupt will
+	 * be generated only when detecting a specific status bit changed
+	 * from '0' to '1'. So when we start waiting for a interrupt, we
+	 * need to check status bit in control reg first, if it is already 1,
+	 * then we do not need to wait for interrupt
+	 */
+	ctrl_reg = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	if (a3700_spi->wait_mask & ctrl_reg)
+		return true;
+
+	reinit_completion(&a3700_spi->done);
+
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG,
+		     a3700_spi->wait_mask);
+
+	timeout_jiffies = msecs_to_jiffies(A3700_SPI_TIMEOUT);
+	timeout = wait_for_completion_timeout(&a3700_spi->done,
+					      timeout_jiffies);
+
+	a3700_spi->wait_mask = 0;
+
+	if (timeout)
+		return true;
+
+	/* there might be the case that right after we checked the
+	 * status bits in this routine and before start to wait for
+	 * interrupt by wait_for_completion_timeout, the interrupt
+	 * happens, to avoid missing it we need to double check
+	 * status bits in control reg, if it is already 1, then
+	 * consider that we have the interrupt successfully and
+	 * return true.
+	 */
+	ctrl_reg = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	if (a3700_spi->wait_mask & ctrl_reg)
+		return true;
+
+	spireg_write(a3700_spi, A3700_SPI_INT_MASK_REG, 0);
+
+	return true;
+}
+
+static bool a3700_spi_transfer_wait(struct spi_device *spi,
+				    unsigned int bit_mask)
+{
+	struct a3700_spi *a3700_spi;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+	a3700_spi->wait_mask = bit_mask;
+
+	return a3700_spi_wait_completion(spi);
+}
+
+static void a3700_spi_fifo_thres_set(struct a3700_spi *a3700_spi,
+				     unsigned int bytes)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val &= ~(A3700_SPI_FIFO_THRS_MASK << A3700_SPI_RFIFO_THRS_BIT);
+	val |= (bytes - 1) << A3700_SPI_RFIFO_THRS_BIT;
+	val &= ~(A3700_SPI_FIFO_THRS_MASK << A3700_SPI_WFIFO_THRS_BIT);
+	val |= (7 - bytes) << A3700_SPI_WFIFO_THRS_BIT;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static void a3700_spi_transfer_setup(struct spi_device *spi,
+				    struct spi_transfer *xfer)
+{
+	struct a3700_spi *a3700_spi;
+	unsigned int byte_len;
+
+	a3700_spi = spi_master_get_devdata(spi->master);
+
+	a3700_spi_clock_set(a3700_spi, xfer->speed_hz, spi->mode);
+
+	byte_len = xfer->bits_per_word >> 3;
+
+	a3700_spi_fifo_thres_set(a3700_spi, byte_len);
+}
+
+static void a3700_spi_set_cs(struct spi_device *spi, bool enable)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(spi->master);
+
+	if (!enable)
+		a3700_spi_activate_cs(a3700_spi, spi->chip_select);
+	else
+		a3700_spi_deactivate_cs(a3700_spi, spi->chip_select);
+}
+
+static void a3700_spi_header_set(struct a3700_spi *a3700_spi)
+{
+	u32 instr_cnt = 0, addr_cnt = 0, dummy_cnt = 0;
+	u32 val = 0;
+
+	/* Clear the header registers */
+	spireg_write(a3700_spi, A3700_SPI_IF_INST_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_ADDR_REG, 0);
+	spireg_write(a3700_spi, A3700_SPI_IF_RMODE_REG, 0);
+
+	/* Set header counters */
+	if (a3700_spi->tx_buf) {
+		if (a3700_spi->buf_len <= a3700_spi->instr_cnt) {
+			instr_cnt = a3700_spi->buf_len;
+		} else if (a3700_spi->buf_len <= (a3700_spi->instr_cnt +
+						  a3700_spi->addr_cnt)) {
+			instr_cnt = a3700_spi->instr_cnt;
+			addr_cnt = a3700_spi->buf_len - instr_cnt;
+		} else if (a3700_spi->buf_len <= a3700_spi->hdr_cnt) {
+			instr_cnt = a3700_spi->instr_cnt;
+			addr_cnt = a3700_spi->addr_cnt;
+			/* Need to handle the normal write case with 1 byte
+			 * data
+			 */
+			if (!a3700_spi->tx_buf[instr_cnt + addr_cnt])
+				dummy_cnt = a3700_spi->buf_len - instr_cnt -
+					    addr_cnt;
+		}
+		val |= ((instr_cnt & A3700_SPI_INSTR_CNT_MASK)
+			<< A3700_SPI_INSTR_CNT_BIT);
+		val |= ((addr_cnt & A3700_SPI_ADDR_CNT_MASK)
+			<< A3700_SPI_ADDR_CNT_BIT);
+		val |= ((dummy_cnt & A3700_SPI_DUMMY_CNT_MASK)
+			<< A3700_SPI_DUMMY_CNT_BIT);
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_HDR_CNT_REG, val);
+
+	/* Update the buffer length to be transferred */
+	a3700_spi->buf_len -= (instr_cnt + addr_cnt + dummy_cnt);
+
+	/* Set Instruction */
+	val = 0;
+	while (instr_cnt--) {
+		val = (val << 8) | a3700_spi->tx_buf[0];
+		a3700_spi->tx_buf++;
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_INST_REG, val);
+
+	/* Set Address */
+	val = 0;
+	while (addr_cnt--) {
+		val = (val << 8) | a3700_spi->tx_buf[0];
+		a3700_spi->tx_buf++;
+	}
+	spireg_write(a3700_spi, A3700_SPI_IF_ADDR_REG, val);
+}
+
+static int a3700_is_wfifo_full(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+	return (val & A3700_SPI_WFIFO_FULL);
+}
+
+static int a3700_spi_fifo_write(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+	int i = 0;
+
+	while (!a3700_is_wfifo_full(a3700_spi) && a3700_spi->buf_len) {
+		val = 0;
+		if (a3700_spi->buf_len >= 4) {
+			val = cpu_to_le32(*(u32 *)a3700_spi->tx_buf);
+			spireg_write(a3700_spi, A3700_SPI_DATA_OUT_REG, val);
+
+			a3700_spi->buf_len -= 4;
+			a3700_spi->tx_buf += 4;
+		} else {
+			/*
+			 * If the remained buffer length is less than 4-bytes,
+			 * we should pad the write buffer with all ones. So that
+			 * it avoids overwrite the unexpected bytes following
+			 * the last one.
+			 */
+			val = GENMASK(31, 0);
+			while (a3700_spi->buf_len) {
+				val &= ~(0xff << (8 * i));
+				val |= *a3700_spi->tx_buf++ << (8 * i);
+				i++;
+				a3700_spi->buf_len--;
+
+				spireg_write(a3700_spi, A3700_SPI_DATA_OUT_REG,
+					     val);
+			}
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static int a3700_is_rfifo_empty(struct a3700_spi *a3700_spi)
+{
+	u32 val = spireg_read(a3700_spi, A3700_SPI_IF_CTRL_REG);
+
+	return (val & A3700_SPI_RFIFO_EMPTY);
+}
+
+static int a3700_spi_fifo_read(struct a3700_spi *a3700_spi)
+{
+	u32 val;
+
+	while (!a3700_is_rfifo_empty(a3700_spi) && a3700_spi->buf_len) {
+		val = spireg_read(a3700_spi, A3700_SPI_DATA_IN_REG);
+		if (a3700_spi->buf_len >= 4) {
+			u32 data = le32_to_cpu(val);
+			memcpy(a3700_spi->rx_buf, &data, 4);
+
+			a3700_spi->buf_len -= 4;
+			a3700_spi->rx_buf += 4;
+		} else {
+			/*
+			 * When remain bytes is not larger than 4, we should
+			 * avoid memory overwriting and just write the left rx
+			 * buffer bytes.
+			 */
+			while (a3700_spi->buf_len) {
+				*a3700_spi->rx_buf = val & 0xff;
+				val >>= 8;
+
+				a3700_spi->buf_len--;
+				a3700_spi->rx_buf++;
+			}
+		}
+	}
+
+	return 0;
+}
+
+static void a3700_spi_transfer_abort_fifo(struct a3700_spi *a3700_spi)
+{
+	int timeout = A3700_SPI_TIMEOUT;
+	u32 val;
+
+	val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+	val |= A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_XFER_START))
+			break;
+		udelay(1);
+	}
+
+	a3700_spi_fifo_flush(a3700_spi);
+
+	val &= ~A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+}
+
+static int a3700_spi_prepare_message(struct spi_master *master,
+				     struct spi_message *message)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+	struct spi_device *spi = message->spi;
+	int ret;
+
+	ret = clk_enable(a3700_spi->clk);
+	if (ret) {
+		dev_err(&spi->dev, "failed to enable clk with error %d\n", ret);
+		return ret;
+	}
+
+	/* Flush the FIFOs */
+	ret = a3700_spi_fifo_flush(a3700_spi);
+	if (ret)
+		return ret;
+
+	a3700_spi_bytelen_set(a3700_spi, 4);
+
+	return 0;
+}
+
+static int a3700_spi_transfer_one(struct spi_master *master,
+				  struct spi_device *spi,
+				  struct spi_transfer *xfer)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+	int ret = 0, timeout = A3700_SPI_TIMEOUT;
+	unsigned int nbits = 0;
+	u32 val;
+
+	a3700_spi_transfer_setup(spi, xfer);
+
+	a3700_spi->tx_buf  = xfer->tx_buf;
+	a3700_spi->rx_buf  = xfer->rx_buf;
+	a3700_spi->buf_len = xfer->len;
+
+	/* SPI transfer headers */
+	a3700_spi_header_set(a3700_spi);
+
+	if (xfer->tx_buf)
+		nbits = xfer->tx_nbits;
+	else if (xfer->rx_buf)
+		nbits = xfer->rx_nbits;
+
+	a3700_spi_pin_mode_set(a3700_spi, nbits);
+
+	if (xfer->rx_buf) {
+		/* Set read data length */
+		spireg_write(a3700_spi, A3700_SPI_IF_DIN_CNT_REG,
+			     a3700_spi->buf_len);
+		/* Start READ transfer */
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val &= ~A3700_SPI_RW_EN;
+		val |= A3700_SPI_XFER_START;
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	} else if (xfer->tx_buf) {
+		/* Start Write transfer */
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val |= (A3700_SPI_XFER_START | A3700_SPI_RW_EN);
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+
+		/*
+		 * If there are data to be written to the SPI device, xmit_data
+		 * flag is set true; otherwise the instruction in SPI_INSTR does
+		 * not require data to be written to the SPI device, then
+		 * xmit_data flag is set false.
+		 */
+		a3700_spi->xmit_data = (a3700_spi->buf_len != 0);
+	}
+
+	while (a3700_spi->buf_len) {
+		if (a3700_spi->tx_buf) {
+			/* Wait wfifo ready */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_WFIFO_RDY)) {
+				dev_err(&spi->dev,
+					"wait wfifo ready timed out\n");
+				ret = -ETIMEDOUT;
+				goto error;
+			}
+			/* Fill up the wfifo */
+			ret = a3700_spi_fifo_write(a3700_spi);
+			if (ret)
+				goto error;
+		} else if (a3700_spi->rx_buf) {
+			/* Wait rfifo ready */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_RFIFO_RDY)) {
+				dev_err(&spi->dev,
+					"wait rfifo ready timed out\n");
+				ret = -ETIMEDOUT;
+				goto error;
+			}
+			/* Drain out the rfifo */
+			ret = a3700_spi_fifo_read(a3700_spi);
+			if (ret)
+				goto error;
+		}
+	}
+
+	/*
+	 * Stop a write transfer in fifo mode:
+	 *	- wait all the bytes in wfifo to be shifted out
+	 *	 - set XFER_STOP bit
+	 *	- wait XFER_START bit clear
+	 *	- clear XFER_STOP bit
+	 * Stop a read transfer in fifo mode:
+	 *	- the hardware is to reset the XFER_START bit
+	 *	   after the number of bytes indicated in DIN_CNT
+	 *	   register
+	 *	- just wait XFER_START bit clear
+	 */
+	if (a3700_spi->tx_buf) {
+		if (a3700_spi->xmit_data) {
+			/*
+			 * If there are data written to the SPI device, wait
+			 * until SPI_WFIFO_EMPTY is 1 to wait for all data to
+			 * transfer out of write FIFO.
+			 */
+			if (!a3700_spi_transfer_wait(spi,
+						     A3700_SPI_WFIFO_EMPTY)) {
+				dev_err(&spi->dev, "wait wfifo empty timed out\n");
+				return -ETIMEDOUT;
+			}
+		} else {
+			/*
+			 * If the instruction in SPI_INSTR does not require data
+			 * to be written to the SPI device, wait until SPI_RDY
+			 * is 1 for the SPI interface to be in idle.
+			 */
+			if (!a3700_spi_transfer_wait(spi, A3700_SPI_XFER_RDY)) {
+				dev_err(&spi->dev, "wait xfer ready timed out\n");
+				return -ETIMEDOUT;
+			}
+		}
+
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		val |= A3700_SPI_XFER_STOP;
+		spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	}
+
+	while (--timeout) {
+		val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG);
+		if (!(val & A3700_SPI_XFER_START))
+			break;
+		udelay(1);
+	}
+
+	if (timeout == 0) {
+		dev_err(&spi->dev, "wait transfer start clear timed out\n");
+		ret = -ETIMEDOUT;
+		goto error;
+	}
+
+	val &= ~A3700_SPI_XFER_STOP;
+	spireg_write(a3700_spi, A3700_SPI_IF_CFG_REG, val);
+	goto out;
+
+error:
+	a3700_spi_transfer_abort_fifo(a3700_spi);
+out:
+	spi_finalize_current_transfer(master);
+
+	return ret;
+}
+
+static int a3700_spi_unprepare_message(struct spi_master *master,
+				       struct spi_message *message)
+{
+	struct a3700_spi *a3700_spi = spi_master_get_devdata(master);
+
+	clk_disable(a3700_spi->clk);
+
+	return 0;
+}
+
+static const struct of_device_id a3700_spi_dt_ids[] = {
+	{ .compatible = "marvell,armada-3700-spi", .data = NULL },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, a3700_spi_dt_ids);
+
+static int a3700_spi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *of_node = dev->of_node;
+	struct resource *res;
+	struct spi_master *master;
+	struct a3700_spi *spi;
+	u32 num_cs = 0;
+	int ret = 0;
+
+	master = spi_alloc_master(dev, sizeof(*spi));
+	if (!master) {
+		dev_err(dev, "master allocation failed\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (of_property_read_u32(of_node, "num-cs", &num_cs)) {
+		dev_err(dev, "could not find num-cs\n");
+		ret = -ENXIO;
+		goto error;
+	}
+
+	master->bus_num = pdev->id;
+	master->dev.of_node = of_node;
+	master->mode_bits = SPI_MODE_3;
+	master->num_chipselect = num_cs;
+	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(32);
+	master->prepare_message =  a3700_spi_prepare_message;
+	master->transfer_one = a3700_spi_transfer_one;
+	master->unprepare_message = a3700_spi_unprepare_message;
+	master->set_cs = a3700_spi_set_cs;
+	master->flags = SPI_MASTER_HALF_DUPLEX;
+	master->mode_bits |= (SPI_RX_DUAL | SPI_RX_DUAL |
+			      SPI_RX_QUAD | SPI_TX_QUAD);
+
+	platform_set_drvdata(pdev, master);
+
+	spi = spi_master_get_devdata(master);
+	memset(spi, 0, sizeof(struct a3700_spi));
+
+	spi->master = master;
+	spi->instr_cnt = A3700_INSTR_CNT;
+	spi->addr_cnt = A3700_ADDR_CNT;
+	spi->hdr_cnt = A3700_INSTR_CNT + A3700_ADDR_CNT +
+		       A3700_DUMMY_CNT;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	spi->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(spi->base)) {
+		ret = PTR_ERR(spi->base);
+		goto error;
+	}
+
+	spi->irq = platform_get_irq(pdev, 0);
+	if (spi->irq < 0) {
+		dev_err(dev, "could not get irq: %d\n", spi->irq);
+		ret = -ENXIO;
+		goto error;
+	}
+
+	init_completion(&spi->done);
+
+	spi->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(spi->clk)) {
+		dev_err(dev, "could not find clk: %ld\n", PTR_ERR(spi->clk));
+		goto error;
+	}
+
+	ret = clk_prepare(spi->clk);
+	if (ret) {
+		dev_err(dev, "could not prepare clk: %d\n", ret);
+		goto error;
+	}
+
+	ret = a3700_spi_init(spi);
+	if (ret)
+		goto error_clk;
+
+	ret = devm_request_irq(dev, spi->irq, a3700_spi_interrupt, 0,
+			       dev_name(dev), master);
+	if (ret) {
+		dev_err(dev, "could not request IRQ: %d\n", ret);
+		goto error_clk;
+	}
+
+	ret = devm_spi_register_master(dev, master);
+	if (ret) {
+		dev_err(dev, "Failed to register master\n");
+		goto error_clk;
+	}
+
+	return 0;
+
+error_clk:
+	clk_disable_unprepare(spi->clk);
+error:
+	spi_master_put(master);
+out:
+	return ret;
+}
+
+static int a3700_spi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct a3700_spi *spi = spi_master_get_devdata(master);
+
+	clk_unprepare(spi->clk);
+	spi_master_put(master);
+
+	return 0;
+}
+
+static struct platform_driver a3700_spi_driver = {
+	.driver = {
+		.name	= DRIVER_NAME,
+		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(a3700_spi_dt_ids),
+	},
+	.probe		= a3700_spi_probe,
+	.remove		= a3700_spi_remove,
+};
+
+module_platform_driver(a3700_spi_driver);
+
+MODULE_DESCRIPTION("Armada-3700 SPI driver");
+MODULE_AUTHOR("Wilson Ding <dingwei-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
-- 
2.10.2

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/4] spi: armada-3700: Add documentation for the Armada 3700 SPI Controller

[Romain Perier]

This adds the devicetree bindings documentation for the SPI controller
present in the Marvell Armada 3700 SoCs.

Signed-off-by: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---

Changes in v4:
 - Added tag "Acked-by" by Rob Herring

Changes in v3:
 - Added tag "Tested-by" by Gregory
 - Fixed commit title, as requested by Mark Brown

 .../devicetree/bindings/spi/spi-armada-3700.txt    | 25 ++++++++++++++++++++++
 1 file changed, 25 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/spi-armada-3700.txt

diff --git a/Documentation/devicetree/bindings/spi/spi-armada-3700.txt b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt
new file mode 100644
index 0000000..1564aa8
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-armada-3700.txt
@@ -0,0 +1,25 @@
+* Marvell Armada 3700 SPI Controller
+
+Required Properties:
+
+- compatible: should be "marvell,armada-3700-spi"
+- reg: physical base address of the controller and length of memory mapped
+       region.
+- interrupts: The interrupt number. The interrupt specifier format depends on
+	      the interrupt controller and of its driver.
+- clocks: Must contain the clock source, usually from the North Bridge clocks.
+- num-cs: The number of chip selects that is supported by this SPI Controller
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+
+Example:
+
+	spi0: spi@10600 {
+		compatible = "marvell,armada-3700-spi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10600 0x5d>;
+		clocks = <&nb_perih_clk 7>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		num-cs = <4>;
+	};
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 3/4] arm64: dts: marvell: Add definition of SPI controller for Armada 3700

[Romain Perier]

Armada 3700 SoC has an SPI Controller, this commit adds the definition
of the SPI device node at the SoC level.

Signed-off-by: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---

Changes in v3:
 - Fixed wrong register size for spi0, as suggested by the maintainer
   on the ML.
 - Added tag "Tested-by" by Gregory

Changes in v2:
 - Removed properties max-frequency and clock-frequency, it is no
   longer required and not used by the DT-bindings.

 arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index e9bd587..fcef9a5 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -98,6 +98,17 @@
 			/* 32M internal register @ 0xd000_0000 */
 			ranges = <0x0 0x0 0xd0000000 0x2000000>;
 
+			spi0: spi@10600 {
+				compatible = "marvell,armada-3700-spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x10600 0xA00>;
+				clocks = <&nb_periph_clk 7>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				num-cs = <4>;
+				status = "disabled";
+			};
+
 			uart0: serial@12000 {
 				compatible = "marvell,armada-3700-uart";
 				reg = <0x12000 0x400>;
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 3/4] arm64: dts: marvell: Add definition of SPI controller for Armada 3700

[Gregory CLEMENT]

Hi Romain,
 
 On jeu., déc. 08 2016, Romain Perier <romain.perier@free-electrons.com> wrote:

> Armada 3700 SoC has an SPI Controller, this commit adds the definition
> of the SPI device node at the SoC level.
>
> Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Applied on mvebu/dt64

Thanks,

Gregory
> ---
>
> Changes in v3:
>  - Fixed wrong register size for spi0, as suggested by the maintainer
>    on the ML.
>  - Added tag "Tested-by" by Gregory
>
> Changes in v2:
>  - Removed properties max-frequency and clock-frequency, it is no
>    longer required and not used by the DT-bindings.
>
>  arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
> index e9bd587..fcef9a5 100644
> --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
> +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
> @@ -98,6 +98,17 @@
>  			/* 32M internal register @ 0xd000_0000 */
>  			ranges = <0x0 0x0 0xd0000000 0x2000000>;
>  
> +			spi0: spi@10600 {
> +				compatible = "marvell,armada-3700-spi";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				reg = <0x10600 0xA00>;
> +				clocks = <&nb_periph_clk 7>;
> +				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +				num-cs = <4>;
> +				status = "disabled";
> +			};
> +
>  			uart0: serial@12000 {
>  				compatible = "marvell,armada-3700-uart";
>  				reg = <0x12000 0x400>;
> -- 
> 2.9.3
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v4 4/4] arm64: dts: marvell: Enable spi0 on the board Armada-3720-db

[Romain Perier]

This commit enables the device node spi0 on the official development
board for the Marvell Armada 3700. It also adds sub-node for the 128Mb
SPI-NOR present on the board.

Signed-off-by: Romain Perier <romain.perier-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Tested-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---

Changes in v3:
 - Added tag "Tested-by" by Gregory

 arch/arm64/boot/dts/marvell/armada-3720-db.dts | 30 ++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
index 1372e9a6..0c4eb98 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
@@ -67,6 +67,36 @@
 	status = "okay";
 };
 
+&spi0 {
+	status = "okay";
+
+	m25p80@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <108000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "bootloader";
+				reg = <0x0 0x200000>;
+			};
+			partition@200000 {
+				label = "U-boot Env";
+				reg = <0x200000 0x10000>;
+			};
+			partition@210000 {
+				label = "Linux";
+				reg = <0x210000 0xDF0000>;
+			};
+		};
+	};
+};
+
 /* Exported on the micro USB connector CON32 through an FTDI */
 &uart0 {
 	status = "okay";
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v4 4/4] arm64: dts: marvell: Enable spi0 on the board Armada-3720-db

[Gregory CLEMENT]

Hi Romain,
 
 On jeu., déc. 08 2016, Romain Perier <romain.perier@free-electrons.com> wrote:

> This commit enables the device node spi0 on the official development
> board for the Marvell Armada 3700. It also adds sub-node for the 128Mb
> SPI-NOR present on the board.
>
> Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Applied on mvebu/dt64

Thanks,

Gregory
> ---
>
> Changes in v3:
>  - Added tag "Tested-by" by Gregory
>
>  arch/arm64/boot/dts/marvell/armada-3720-db.dts | 30 ++++++++++++++++++++++++++
>  1 file changed, 30 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
> index 1372e9a6..0c4eb98 100644
> --- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
> @@ -67,6 +67,36 @@
>  	status = "okay";
>  };
>  
> +&spi0 {
> +	status = "okay";
> +
> +	m25p80@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <108000000>;
> +		spi-rx-bus-width = <4>;
> +		spi-tx-bus-width = <4>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			partition@0 {
> +				label = "bootloader";
> +				reg = <0x0 0x200000>;
> +			};
> +			partition@200000 {
> +				label = "U-boot Env";
> +				reg = <0x200000 0x10000>;
> +			};
> +			partition@210000 {
> +				label = "Linux";
> +				reg = <0x210000 0xDF0000>;
> +			};
> +		};
> +	};
> +};
> +
>  /* Exported on the micro USB connector CON32 through an FTDI */
>  &uart0 {
>  	status = "okay";
> -- 
> 2.9.3
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel