Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
From: Pratyush Yadav <p.yadav@ti.com>
To: Tudor Ambarus <tudor.ambarus@microchip.com>,
	Miquel Raynal <miquel.raynal@bootlin.com>,
	Richard Weinberger <richard@nod.at>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Mark Brown <broonie@kernel.org>,
	Nicolas Ferre <nicolas.ferre@microchip.com>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>,
	Ludovic Desroches <ludovic.desroches@microchip.com>,
	Matthias Brugger <matthias.bgg@gmail.com>,
	Michal Simek <michal.simek@xilinx.com>,
	<linux-mtd@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
	<linux-spi@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-mediatek@lists.infradead.org>
Cc: Pratyush Yadav <p.yadav@ti.com>, Sekhar Nori <nsekhar@ti.com>,
	Boris Brezillon <boris.brezillon@collabora.com>,
	Mason Yang <masonccyang@mxic.com.tw>
Subject: [PATCH v8 09/19] mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table
Date: Sat, 23 May 2020 04:10:32 +0530
Message-ID: <20200522224042.29970-10-p.yadav@ti.com> (raw)
In-Reply-To: <20200522224042.29970-1-p.yadav@ti.com>

This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
dummy cycles, the number of dummy cycles needed for a Read Status
Register command, and the number of address bytes needed for a Read
Status Register command.

We don't know what speed the controller is running at. Find the fast
read dummy cycles for the fastest frequency the flash can run at to be
sure we are never short of dummy cycles. If nothing is available,
default to 20. Flashes that use a different value should update it in
their fixup hooks.

Since we want to set read settings, expose spi_nor_set_read_settings()
in core.h.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/core.c |  2 +-
 drivers/mtd/spi-nor/core.h | 10 ++++
 drivers/mtd/spi-nor/sfdp.c | 99 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 110 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 388e695e763f..642e3c07acf9 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2355,7 +2355,7 @@ static int spi_nor_check(struct spi_nor *nor)
 	return 0;
 }
 
-static void
+void
 spi_nor_set_read_settings(struct spi_nor_read_command *read,
 			  u8 num_mode_clocks,
 			  u8 num_wait_states,
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index de1e3917889f..7e6df8322da0 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -192,6 +192,9 @@ struct spi_nor_locking_ops {
  *
  * @size:		the flash memory density in bytes.
  * @page_size:		the page size of the SPI NOR flash memory.
+ * @rdsr_dummy:		dummy cycles needed for Read Status Register command.
+ * @rdsr_addr_nbytes:	dummy address bytes needed for Read Status Register
+ *			command.
  * @hwcaps:		describes the read and page program hardware
  *			capabilities.
  * @reads:		read capabilities ordered by priority: the higher index
@@ -214,6 +217,8 @@ struct spi_nor_locking_ops {
 struct spi_nor_flash_parameter {
 	u64				size;
 	u32				page_size;
+	u8				rdsr_dummy;
+	u8				rdsr_addr_nbytes;
 
 	struct spi_nor_hwcaps		hwcaps;
 	struct spi_nor_read_command	reads[SNOR_CMD_READ_MAX];
@@ -424,6 +429,11 @@ ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
 
 int spi_nor_hwcaps_read2cmd(u32 hwcaps);
 u8 spi_nor_convert_3to4_read(u8 opcode);
+void spi_nor_set_read_settings(struct spi_nor_read_command *read,
+			      u8 num_mode_clocks,
+			      u8 num_wait_states,
+			      u8 opcode,
+			      enum spi_nor_protocol proto);
 void spi_nor_set_pp_settings(struct spi_nor_pp_command *pp, u8 opcode,
 			     enum spi_nor_protocol proto);
 
diff --git a/drivers/mtd/spi-nor/sfdp.c b/drivers/mtd/spi-nor/sfdp.c
index ab086aa4746f..052cabb52df9 100644
--- a/drivers/mtd/spi-nor/sfdp.c
+++ b/drivers/mtd/spi-nor/sfdp.c
@@ -4,12 +4,15 @@
  * Copyright (C) 2014, Freescale Semiconductor, Inc.
  */
 
+#include <linux/bitfield.h>
 #include <linux/slab.h>
 #include <linux/sort.h>
 #include <linux/mtd/spi-nor.h>
 
 #include "core.h"
 
+#define ROUND_UP_TO(x, y)	(((x) + (y) - 1) / (y) * (y))
+
 #define SFDP_PARAM_HEADER_ID(p)	(((p)->id_msb << 8) | (p)->id_lsb)
 #define SFDP_PARAM_HEADER_PTP(p) \
 	(((p)->parameter_table_pointer[2] << 16) | \
@@ -19,12 +22,14 @@
 #define SFDP_BFPT_ID		0xff00	/* Basic Flash Parameter Table */
 #define SFDP_SECTOR_MAP_ID	0xff81	/* Sector Map Table */
 #define SFDP_4BAIT_ID		0xff84  /* 4-byte Address Instruction Table */
+#define SFDP_PROFILE1_ID	0xff05	/* xSPI Profile 1.0 table. */
 
 #define SFDP_SIGNATURE		0x50444653U
 #define SFDP_JESD216_MAJOR	1
 #define SFDP_JESD216_MINOR	0
 #define SFDP_JESD216A_MINOR	5
 #define SFDP_JESD216B_MINOR	6
+#define SFDP_JESD216D_MINOR	8
 
 struct sfdp_header {
 	u32		signature; /* Ox50444653U <=> "SFDP" */
@@ -70,6 +75,16 @@ struct sfdp_bfpt_erase {
 	u32			shift;
 };
 
+/* xSPI Profile 1.0 table (from JESD216D.01). */
+#define PROFILE1_DWORD1_RD_FAST_CMD		GENMASK(15, 8)
+#define PROFILE1_DWORD1_RDSR_DUMMY		BIT(28)
+#define PROFILE1_DWORD1_RDSR_ADDR_BYTES		BIT(29)
+#define PROFILE1_DWORD4_DUMMY_200MHZ		GENMASK(11, 7)
+#define PROFILE1_DWORD5_DUMMY_166MHZ		GENMASK(31, 27)
+#define PROFILE1_DWORD5_DUMMY_133MHZ		GENMASK(21, 17)
+#define PROFILE1_DWORD5_DUMMY_100MHZ		GENMASK(11, 7)
+#define PROFILE1_DUMMY_DEFAULT			20
+
 #define SMPT_CMD_ADDRESS_LEN_MASK		GENMASK(23, 22)
 #define SMPT_CMD_ADDRESS_LEN_0			(0x0UL << 22)
 #define SMPT_CMD_ADDRESS_LEN_3			(0x1UL << 22)
@@ -1110,6 +1125,86 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
 	return ret;
 }
 
+/**
+ * spi_nor_parse_profile1() - parse the xSPI Profile 1.0 table
+ * @nor:		pointer to a 'struct spi_nor'
+ * @param_header:	pointer to the 'struct sfdp_parameter_header' describing
+ *			the 4-Byte Address Instruction Table length and version.
+ * @params:		pointer to the 'struct spi_nor_flash_parameter' to be.
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_parse_profile1(struct spi_nor *nor,
+				  const struct sfdp_parameter_header *profile1_header,
+				  struct spi_nor_flash_parameter *params)
+{
+	u32 *table, opcode, addr;
+	size_t len;
+	int ret, i;
+	u8 dummy;
+
+	len = profile1_header->length * sizeof(*table);
+	table = kmalloc(len, GFP_KERNEL);
+	if (!table)
+		return -ENOMEM;
+
+	addr = SFDP_PARAM_HEADER_PTP(profile1_header);
+	ret = spi_nor_read_sfdp(nor, addr, len, table);
+	if (ret)
+		goto out;
+
+	/* Fix endianness of the table DWORDs. */
+	for (i = 0; i < profile1_header->length; i++)
+		table[i] = le32_to_cpu(table[i]);
+
+	/* Get 8D-8D-8D fast read opcode and dummy cycles. */
+	opcode = FIELD_GET(PROFILE1_DWORD1_RD_FAST_CMD, table[0]);
+
+	/*
+	 * We don't know what speed the controller is running at. Find the
+	 * dummy cycles for the fastest frequency the flash can run at to be
+	 * sure we are never short of dummy cycles. A value of 0 means the
+	 * frequency is not supported.
+	 *
+	 * Default to PROFILE1_DUMMY_DEFAULT if we don't find anything, and let
+	 * flashes set the correct value if needed in their fixup hooks.
+	 */
+	dummy = FIELD_GET(PROFILE1_DWORD4_DUMMY_200MHZ, table[3]);
+	if (!dummy)
+		dummy = FIELD_GET(PROFILE1_DWORD5_DUMMY_166MHZ, table[4]);
+	if (!dummy)
+		dummy = FIELD_GET(PROFILE1_DWORD5_DUMMY_133MHZ, table[4]);
+	if (!dummy)
+		dummy = FIELD_GET(PROFILE1_DWORD5_DUMMY_100MHZ, table[4]);
+	if (!dummy)
+		dummy = PROFILE1_DUMMY_DEFAULT;
+
+	/* Round up to an even value to avoid tripping controllers up. */
+	dummy = ROUND_UP_TO(dummy, 2);
+
+	/* Update the fast read settings. */
+	spi_nor_set_read_settings(&params->reads[SNOR_CMD_READ_8_8_8_DTR],
+				  0, dummy, opcode,
+				  SNOR_PROTO_8_8_8_DTR);
+
+	/*
+	 * Set the Read Status Register dummy cycles and dummy address bytes.
+	 */
+	if (table[0] & PROFILE1_DWORD1_RDSR_DUMMY)
+		params->rdsr_dummy = 8;
+	else
+		params->rdsr_dummy = 4;
+
+	if (table[0] & PROFILE1_DWORD1_RDSR_ADDR_BYTES)
+		params->rdsr_addr_nbytes = 4;
+	else
+		params->rdsr_addr_nbytes = 0;
+
+out:
+	kfree(table);
+	return ret;
+}
+
 /**
  * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
  * @nor:		pointer to a 'struct spi_nor'
@@ -1211,6 +1306,10 @@ int spi_nor_parse_sfdp(struct spi_nor *nor,
 			err = spi_nor_parse_4bait(nor, param_header, params);
 			break;
 
+		case SFDP_PROFILE1_ID:
+			err = spi_nor_parse_profile1(nor, param_header, params);
+			break;
+
 		default:
 			break;
 		}
-- 
2.26.2


  parent reply index

Thread overview: 21+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-05-22 22:40 [PATCH v8 00/19] mtd: spi-nor: add xSPI Octal DTR support Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 01/19] spi: spi-mem: allow specifying whether an op is DTR or not Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 02/19] spi: spi-mem: allow specifying a command's extension Pratyush Yadav
2020-05-24 20:17   ` Boris Brezillon
2020-05-22 22:40 ` [PATCH v8 03/19] spi: atmel-quadspi: reject DTR ops Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 04/19] spi: spi-mtk-nor: " Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 05/19] mtd: spi-nor: add support for DTR protocol Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 06/19] mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 07/19] mtd: spi-nor: sfdp: prepare BFPT parsing for JESD216 rev D Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 08/19] mtd: spi-nor: sfdp: get command opcode extension type from BFPT Pratyush Yadav
2020-05-22 22:40 ` Pratyush Yadav [this message]
2020-05-22 22:40 ` [PATCH v8 10/19] mtd: spi-nor: core: use dummy cycle and address width info from SFDP Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 11/19] mtd: spi-nor: core: do 2 byte reads for SR and FSR in DTR mode Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 12/19] mtd: spi-nor: core: enable octal DTR mode when possible Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 13/19] mtd: spi-nor: sfdp: do not make invalid quad enable fatal Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 14/19] mtd: spi-nor: sfdp: detect Soft Reset sequence support from BFPT Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 15/19] mtd: spi-nor: core: perform a Soft Reset on shutdown Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 16/19] mtd: spi-nor: core: disable Octal DTR mode on suspend Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 17/19] mtd: spi-nor: core: expose spi_nor_default_setup() in core.h Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 18/19] mtd: spi-nor: spansion: add support for Cypress Semper flash Pratyush Yadav
2020-05-22 22:40 ` [PATCH v8 19/19] mtd: spi-nor: micron-st: allow using MT35XU512ABA in Octal DTR mode Pratyush Yadav

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200522224042.29970-10-p.yadav@ti.com \
    --to=p.yadav@ti.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=boris.brezillon@collabora.com \
    --cc=broonie@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mediatek@lists.infradead.org \
    --cc=linux-mtd@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=ludovic.desroches@microchip.com \
    --cc=masonccyang@mxic.com.tw \
    --cc=matthias.bgg@gmail.com \
    --cc=michal.simek@xilinx.com \
    --cc=miquel.raynal@bootlin.com \
    --cc=nicolas.ferre@microchip.com \
    --cc=nsekhar@ti.com \
    --cc=richard@nod.at \
    --cc=tudor.ambarus@microchip.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git