Linux-SPI Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH] Remove BCM2835 SPI chipselect limit.
@ 2021-04-14 12:25 Joe Burmeister
  0 siblings, 0 replies; only message in thread
From: Joe Burmeister @ 2021-04-14 12:25 UTC (permalink / raw)
  To: joe.burmeister, Mark Brown, Nicolas Saenz Julienne,
	Florian Fainelli, Ray Jui, Scott Branden,
	bcm-kernel-feedback-list, linux-spi, linux-rpi-kernel,
	linux-arm-kernel, linux-kernel

The limit of 4 chipselects for the BCM2835 was not required and also was
not inforced. Without inforcement it was possible to make a device tree
over this limit which would trample memory.

The chipselect count is now obtained from the device tree and expanded
if more devices are added.

Signed-off-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
---
 drivers/spi/spi-bcm2835.c | 114 +++++++++++++++++++++++++++++++++-----
 1 file changed, 101 insertions(+), 13 deletions(-)

diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
index aab6c7e5c114..4f215ec3bd1b 100644
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -28,6 +28,7 @@
 #include <linux/gpio/consumer.h>
 #include <linux/gpio/machine.h> /* FIXME: using chip internals */
 #include <linux/gpio/driver.h> /* FIXME: using chip internals */
+#include <linux/of_gpio.h>
 #include <linux/of_irq.h>
 #include <linux/spi/spi.h>
 
@@ -134,7 +135,8 @@ struct bcm2835_spi {
 	int tx_prologue;
 	int rx_prologue;
 	unsigned int tx_spillover;
-	u32 prepare_cs[BCM2835_SPI_NUM_CS];
+	unsigned int allocated_cs_num;
+	u32 *prepare_cs;
 
 	struct dentry *debugfs_dir;
 	u64 count_transfer_polling;
@@ -147,9 +149,9 @@ struct bcm2835_spi {
 	unsigned int rx_dma_active;
 	struct dma_async_tx_descriptor *fill_tx_desc;
 	dma_addr_t fill_tx_addr;
-	struct dma_async_tx_descriptor *clear_rx_desc[BCM2835_SPI_NUM_CS];
+	struct dma_async_tx_descriptor **clear_rx_desc;
 	dma_addr_t clear_rx_addr;
-	u32 clear_rx_cs[BCM2835_SPI_NUM_CS] ____cacheline_aligned;
+	u32 *clear_rx_cs;
 };
 
 #if defined(CONFIG_DEBUG_FS)
@@ -859,14 +861,18 @@ static void bcm2835_dma_release(struct spi_controller *ctlr,
 	if (ctlr->dma_tx) {
 		dmaengine_terminate_sync(ctlr->dma_tx);
 
-		if (bs->fill_tx_desc)
+		if (bs->fill_tx_desc) {
 			dmaengine_desc_free(bs->fill_tx_desc);
+			bs->fill_tx_desc = NULL;
+		}
 
-		if (bs->fill_tx_addr)
+		if (bs->fill_tx_addr) {
 			dma_unmap_page_attrs(ctlr->dma_tx->device->dev,
 					     bs->fill_tx_addr, sizeof(u32),
 					     DMA_TO_DEVICE,
 					     DMA_ATTR_SKIP_CPU_SYNC);
+			bs->fill_tx_addr = 0;
+		}
 
 		dma_release_channel(ctlr->dma_tx);
 		ctlr->dma_tx = NULL;
@@ -875,15 +881,19 @@ static void bcm2835_dma_release(struct spi_controller *ctlr,
 	if (ctlr->dma_rx) {
 		dmaengine_terminate_sync(ctlr->dma_rx);
 
-		for (i = 0; i < BCM2835_SPI_NUM_CS; i++)
-			if (bs->clear_rx_desc[i])
+		for (i = 0; i < bs->allocated_cs_num; i++)
+			if (bs->clear_rx_desc[i]) {
 				dmaengine_desc_free(bs->clear_rx_desc[i]);
+				bs->clear_rx_desc[i] = NULL;
+			}
 
-		if (bs->clear_rx_addr)
+		if (bs->clear_rx_addr) {
 			dma_unmap_single(ctlr->dma_rx->device->dev,
 					 bs->clear_rx_addr,
-					 sizeof(bs->clear_rx_cs),
+					 sizeof(u32) * bs->allocated_cs_num,
 					 DMA_TO_DEVICE);
+			bs->clear_rx_addr = 0;
+		}
 
 		dma_release_channel(ctlr->dma_rx);
 		ctlr->dma_rx = NULL;
@@ -978,7 +988,7 @@ static int bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 
 	bs->clear_rx_addr = dma_map_single(ctlr->dma_rx->device->dev,
 					   bs->clear_rx_cs,
-					   sizeof(bs->clear_rx_cs),
+					   sizeof(u32) * bs->allocated_cs_num,
 					   DMA_TO_DEVICE);
 	if (dma_mapping_error(ctlr->dma_rx->device->dev, bs->clear_rx_addr)) {
 		dev_err(dev, "cannot map clear_rx_cs - not using DMA mode\n");
@@ -987,7 +997,7 @@ static int bcm2835_dma_init(struct spi_controller *ctlr, struct device *dev,
 		goto err_release;
 	}
 
-	for (i = 0; i < BCM2835_SPI_NUM_CS; i++) {
+	for (i = 0; i < bs->allocated_cs_num; i++) {
 		bs->clear_rx_desc[i] = dmaengine_prep_dma_cyclic(ctlr->dma_rx,
 					   bs->clear_rx_addr + i * sizeof(u32),
 					   sizeof(u32), 0,
@@ -1209,6 +1219,48 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 	struct gpio_chip *chip;
 	u32 cs;
 
+	if (spi->chip_select >= bs->allocated_cs_num) {
+		unsigned int new_allocated_cs_num = spi->chip_select + 1;
+		void *new_prepare_cs, *new_clear_rx_desc, *new_clear_rx_cs;
+		int err;
+
+		dev_info(&spi->dev, "Increasing CS count to %u\n",
+			new_allocated_cs_num);
+
+		bcm2835_dma_release(ctlr, bs);
+
+		new_prepare_cs  = kmalloc_array(new_allocated_cs_num,
+			sizeof(u32), GFP_KERNEL);
+		new_clear_rx_desc = kmalloc_array(new_allocated_cs_num,
+			sizeof(struct dma_async_tx_descriptor *), GFP_KERNEL);
+		new_clear_rx_cs = kmalloc_array(new_allocated_cs_num,
+			sizeof(u32), GFP_DMA);
+
+		if (!new_prepare_cs || !new_clear_rx_desc || !new_clear_rx_cs) {
+			dev_err(&spi->dev, "Failed to allocate new CS arrays.\n");
+			return -ENOMEM;
+		}
+
+		memcpy(new_prepare_cs, bs->prepare_cs,
+			bs->allocated_cs_num * sizeof(u32));
+
+		kfree(bs->prepare_cs);
+		kfree(bs->clear_rx_desc);
+		kfree(bs->clear_rx_cs);
+
+		bs->prepare_cs  = new_prepare_cs;
+		bs->clear_rx_desc = new_clear_rx_desc;
+		bs->clear_rx_cs = new_clear_rx_cs;
+
+		bs->allocated_cs_num = new_allocated_cs_num;
+
+		err = bcm2835_dma_init(ctlr, &spi->dev, bs);
+		if (err) {
+			dev_err(&spi->dev, "Failed to reinit DMA after CS count change.");
+			return err;
+		}
+	}
+
 	/*
 	 * Precalculate SPI slave's CS register value for ->prepare_message():
 	 * The driver always uses software-controlled GPIO chip select, hence
@@ -1233,7 +1285,7 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 						    BCM2835_SPI_CS_CLEAR_RX;
 		dma_sync_single_for_device(ctlr->dma_rx->device->dev,
 					   bs->clear_rx_addr,
-					   sizeof(bs->clear_rx_cs),
+					   sizeof(u32) * bs->allocated_cs_num,
 					   DMA_TO_DEVICE);
 	}
 
@@ -1248,6 +1300,7 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 	 */
 	if (spi->cs_gpiod)
 		return 0;
+
 	if (spi->chip_select > 1) {
 		/* error in the case of native CS requested with CS > 1
 		 * officially there is a CS2, but it is not documented
@@ -1286,10 +1339,25 @@ static int bcm2835_spi_setup(struct spi_device *spi)
 	return 0;
 }
 
+
+#ifdef CONFIG_OF
+static int bcm2835_spi_get_num_chipselect(struct platform_device *pdev)
+{
+	return max_t(int, of_gpio_named_count(pdev->dev.of_node, "cs-gpios"), BCM2835_SPI_NUM_CS);
+}
+#else
+static int bcm2835_spi_get_num_chipselect(struct platform_device *pdev)
+{
+	return BCM2835_SPI_NUM_CS;
+}
+#endif
+
+
 static int bcm2835_spi_probe(struct platform_device *pdev)
 {
 	struct spi_controller *ctlr;
 	struct bcm2835_spi *bs;
+	int num_chipselect;
 	int err;
 
 	ctlr = devm_spi_alloc_master(&pdev->dev, ALIGN(sizeof(*bs),
@@ -1297,12 +1365,14 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 	if (!ctlr)
 		return -ENOMEM;
 
+	num_chipselect = bcm2835_spi_get_num_chipselect(pdev);
+
 	platform_set_drvdata(pdev, ctlr);
 
 	ctlr->use_gpio_descriptors = true;
 	ctlr->mode_bits = BCM2835_SPI_MODE_BITS;
 	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
-	ctlr->num_chipselect = BCM2835_SPI_NUM_CS;
+	ctlr->num_chipselect = num_chipselect;
 	ctlr->setup = bcm2835_spi_setup;
 	ctlr->transfer_one = bcm2835_spi_transfer_one;
 	ctlr->handle_err = bcm2835_spi_handle_err;
@@ -1311,6 +1381,20 @@ static int bcm2835_spi_probe(struct platform_device *pdev)
 
 	bs = spi_controller_get_devdata(ctlr);
 	bs->ctlr = ctlr;
+	bs->allocated_cs_num = num_chipselect;
+
+	bs->prepare_cs = kmalloc_array(num_chipselect, sizeof(u32), GFP_KERNEL);
+	if (!bs->prepare_cs)
+		return -ENOMEM;
+
+	bs->clear_rx_desc = kmalloc_array(num_chipselect,
+		sizeof(struct dma_async_tx_descriptor *), GFP_KERNEL);
+	if (!bs->clear_rx_desc)
+		return -ENOMEM;
+
+	bs->clear_rx_cs = kmalloc_array(num_chipselect, sizeof(u32), GFP_DMA);
+	if (!bs->clear_rx_cs)
+		return -ENOMEM;
 
 	bs->regs = devm_platform_ioremap_resource(pdev, 0);
 	if (IS_ERR(bs->regs))
@@ -1378,6 +1462,10 @@ static int bcm2835_spi_remove(struct platform_device *pdev)
 
 	clk_disable_unprepare(bs->clk);
 
+	kfree(bs->prepare_cs);
+	kfree(bs->clear_rx_desc);
+	kfree(bs->clear_rx_cs);
+
 	return 0;
 }
 
-- 
2.30.2


^ permalink raw reply	[flat|nested] only message in thread

only message in thread, back to index

Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-14 12:25 [PATCH] Remove BCM2835 SPI chipselect limit Joe Burmeister

Linux-SPI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-spi/0 linux-spi/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-spi linux-spi/ https://lore.kernel.org/linux-spi \
		linux-spi@vger.kernel.org
	public-inbox-index linux-spi

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-spi


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git