From: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
To: Vasily Khoruzhick <anarsoul@gmail.com>,
Yangtao Li <tiny.windzz@gmail.com>,
"Rafael J. Wysocki" <rafael@kernel.org>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Amit Kucheria <amitk@kernel.org>, Zhang Rui <rui.zhang@intel.com>,
Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>,
Philipp Zabel <p.zabel@pengutronix.de>,
Ondrej Jirman <megous@megous.com>,
Maxime Ripard <mripard@kernel.org>
Cc: linux-kernel@vger.kernel.org, kernel-janitors@vger.kernel.org,
Christophe JAILLET <christophe.jaillet@wanadoo.fr>,
linux-pm@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev
Subject: [PATCH v2] thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe()
Date: Sun, 14 May 2023 20:46:05 +0200 [thread overview]
Message-ID: <a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr> (raw)
Should an error occur after calling sun8i_ths_resource_init() in the probe
function, some resources need to be released, as already done in the
.remove() function.
Switch to the devm_clk_get_enabled() helper and add a new devm_action to
turn sun8i_ths_resource_init() into a fully managed function.
Move the place where reset_control_deassert() is called so that the
recommended order of reset release/clock enable steps is kept.
A64 manual states that:
3.3.6.4. Gating and reset
Make sure that the reset signal has been released before the release of
module clock gating;
This fixes the issue and removes some LoC at the same time.
Fixes: dccc5c3b6f30 ("thermal/drivers/sun8i: Add thermal driver for H6/H5/H3/A64/A83T/R40")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
---
Changes in v2:
- move reset_control_deassert() next to devm_reset_control_get()
v1: https://lore.kernel.org/all/26f9e3bb3fcd0c12ea24a44c75b7960da993b68b.1684077651.git.christophe.jaillet@wanadoo.fr/
---
drivers/thermal/sun8i_thermal.c | 55 +++++++++++----------------------
1 file changed, 18 insertions(+), 37 deletions(-)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 793ddce72132..d4d241686c81 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -319,6 +319,11 @@ static int sun8i_ths_calibrate(struct ths_device *tmdev)
return ret;
}
+static void sun8i_ths_reset_control_assert(void *data)
+{
+ reset_control_assert(data);
+}
+
static int sun8i_ths_resource_init(struct ths_device *tmdev)
{
struct device *dev = tmdev->dev;
@@ -339,47 +344,35 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
if (IS_ERR(tmdev->reset))
return PTR_ERR(tmdev->reset);
- tmdev->bus_clk = devm_clk_get(&pdev->dev, "bus");
+ ret = reset_control_deassert(tmdev->reset);
+ if (ret)
+ return ret;
+
+ ret = devm_add_action_or_reset(dev, sun8i_ths_reset_control_assert,
+ tmdev->reset);
+ if (ret)
+ return ret;
+
+ tmdev->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus");
if (IS_ERR(tmdev->bus_clk))
return PTR_ERR(tmdev->bus_clk);
}
if (tmdev->chip->has_mod_clk) {
- tmdev->mod_clk = devm_clk_get(&pdev->dev, "mod");
+ tmdev->mod_clk = devm_clk_get_enabled(&pdev->dev, "mod");
if (IS_ERR(tmdev->mod_clk))
return PTR_ERR(tmdev->mod_clk);
}
- ret = reset_control_deassert(tmdev->reset);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(tmdev->bus_clk);
- if (ret)
- goto assert_reset;
-
ret = clk_set_rate(tmdev->mod_clk, 24000000);
if (ret)
- goto bus_disable;
-
- ret = clk_prepare_enable(tmdev->mod_clk);
- if (ret)
- goto bus_disable;
+ return ret;
ret = sun8i_ths_calibrate(tmdev);
if (ret)
- goto mod_disable;
+ return ret;
return 0;
-
-mod_disable:
- clk_disable_unprepare(tmdev->mod_clk);
-bus_disable:
- clk_disable_unprepare(tmdev->bus_clk);
-assert_reset:
- reset_control_assert(tmdev->reset);
-
- return ret;
}
static int sun8i_h3_thermal_init(struct ths_device *tmdev)
@@ -530,17 +523,6 @@ static int sun8i_ths_probe(struct platform_device *pdev)
return 0;
}
-static int sun8i_ths_remove(struct platform_device *pdev)
-{
- struct ths_device *tmdev = platform_get_drvdata(pdev);
-
- clk_disable_unprepare(tmdev->mod_clk);
- clk_disable_unprepare(tmdev->bus_clk);
- reset_control_assert(tmdev->reset);
-
- return 0;
-}
-
static const struct ths_thermal_chip sun8i_a83t_ths = {
.sensor_num = 3,
.scale = 705,
@@ -642,7 +624,6 @@ MODULE_DEVICE_TABLE(of, of_ths_match);
static struct platform_driver ths_driver = {
.probe = sun8i_ths_probe,
- .remove = sun8i_ths_remove,
.driver = {
.name = "sun8i-thermal",
.of_match_table = of_ths_match,
--
2.34.1
next reply other threads:[~2023-05-14 18:53 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-14 18:46 Christophe JAILLET [this message]
2023-05-15 11:54 ` [PATCH v2] thermal/drivers/sun8i: Fix some error handling paths in sun8i_ths_probe() Maxime Ripard
2023-05-15 12:33 ` Ondřej Jirman
2023-06-13 8:49 ` Daniel Lezcano
2023-06-13 9:16 ` Maxime Ripard
2023-06-13 9:17 ` Daniel Lezcano
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a8ae84bd2dc4b55fe428f8e20f31438bf8bb6762.1684089931.git.christophe.jaillet@wanadoo.fr \
--to=christophe.jaillet@wanadoo.fr \
--cc=amitk@kernel.org \
--cc=anarsoul@gmail.com \
--cc=daniel.lezcano@linaro.org \
--cc=jernej.skrabec@gmail.com \
--cc=kernel-janitors@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=megous@megous.com \
--cc=mripard@kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=rafael@kernel.org \
--cc=rui.zhang@intel.com \
--cc=samuel@sholland.org \
--cc=tiny.windzz@gmail.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).