[PATCH v4 00/12] soc: qcom: add UCSI function to PMIC GLINK

[PATCH v4 00/12] soc: qcom: add UCSI function to PMIC GLINK

[Neil Armstrong]

The PMIC GLINK interface offers an UCSI endpoint for newer
SoCs, the UCSI exchange is necessary to configure the USB-C
port USB role and altmode on the SM8450 HDK and SM8550 MTP
boards.
Since the DT description is the same, support for SM8350 HDK
is also added.

This patchset focuses on USB and disables altmode support
on those 2 SoCs until DP altmode over the combo phy is
supported.

Depends on PMIC Glink patchset at [1].

[1] https://lore.kernel.org/all/20230130042003.577063-1-quic_bjorande@quicinc.com/

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Changes in v4:
- Handle remove for UCSI driver
- Fixup client mask match data handling
- Added USB ports bindings review tag
- Link to v3: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v3-0-4c860d265d28@linaro.org

Changes in v3:
- Fixed patch 1 by moving mask to pmic_glink_of_match
- Fixed patch 8 by adding back hsphy
- Add bindings change to dwc3 to support separate HS & SS OF graph links
- Link to v2: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v2-0-71fea256474f@linaro.org

Changes in v2:
- Moved the dwc3 port subnodes to dtsi
- Added SM8350 HDK support
- Added help about ucsi module name
- Added bindings acks
- Fixed sm8550 pmic glink compatible
- Added more description in config update patch
- Link to v1: https://lore.kernel.org/r/20230130-topic-sm8450-upstream-pmic-glink-v1-0-0b0acfad301e@linaro.org

---
Neil Armstrong (12):
      usb: typec: ucsi: add PMIC Glink UCSI driver
      dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible
      dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible
      soc: qcom: pmic_glink: register ucsi aux device
      dt-bindings: usb: snps,dwc3: document HS & SS OF graph ports
      arm64: dts: qcom: sm8350: add port subnodes in dwc3 node
      arm64: dts: qcom: sm8450: add port subnodes in dwc3 node
      arm64: dts: qcom: sm8550: add port subnodes in dwc3 node
      arm64: dts: qcom: sm8350-hdk: add pmic glink node
      arm64: dts: qcom: sm8450-hdk: add pmic glink node
      arm64: dts: qcom: sm8550-mtp: add pmic glink node
      arm64: defconfig: add PMIC GLINK modules

 .../bindings/soc/qcom/qcom,pmic-glink.yaml         |   2 +
 .../devicetree/bindings/usb/snps,dwc3.yaml         |  16 +
 arch/arm64/boot/dts/qcom/sm8350-hdk.dts            |  67 +++-
 arch/arm64/boot/dts/qcom/sm8350.dtsi               |  19 ++
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts            |  45 ++-
 arch/arm64/boot/dts/qcom/sm8450.dtsi               |  19 ++
 arch/arm64/boot/dts/qcom/sm8550-mtp.dts            |  45 ++-
 arch/arm64/boot/dts/qcom/sm8550.dtsi               |  19 ++
 arch/arm64/configs/defconfig                       |   4 +
 drivers/soc/qcom/pmic_glink.c                      |  65 +++-
 drivers/usb/typec/ucsi/Kconfig                     |  10 +
 drivers/usb/typec/ucsi/Makefile                    |   1 +
 drivers/usb/typec/ucsi/ucsi_glink.c                | 345 +++++++++++++++++++++
 13 files changed, 642 insertions(+), 15 deletions(-)
---
base-commit: 6f72958a49f68553f2b6ff713e8c8e51a34c1e1e
change-id: 20230130-topic-sm8450-upstream-pmic-glink-3b3a0b7bcd33

Best regards,
-- 
Neil Armstrong <neil.armstrong@linaro.org>

[PATCH v4 01/12] usb: typec: ucsi: add PMIC Glink UCSI driver

[Neil Armstrong]

Introduce the UCSI PMIC Glink aux driver that communicates
with the aDSP firmware with the UCSI protocol which handles
the USB-C Port(s) Power Delivery.

The UCSI messaging is necessary on newer Qualcomm SoCs to
provide USB role switch and altmode notifications.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/usb/typec/ucsi/Kconfig      |  10 ++
 drivers/usb/typec/ucsi/Makefile     |   1 +
 drivers/usb/typec/ucsi/ucsi_glink.c | 345 ++++++++++++++++++++++++++++++++++++
 3 files changed, 356 insertions(+)

diff --git a/drivers/usb/typec/ucsi/Kconfig b/drivers/usb/typec/ucsi/Kconfig
index 8f9c4b9f31f7..b3bb0191987e 100644
--- a/drivers/usb/typec/ucsi/Kconfig
+++ b/drivers/usb/typec/ucsi/Kconfig
@@ -58,4 +58,14 @@ config UCSI_STM32G0
 	  To compile the driver as a module, choose M here: the module will be
 	  called ucsi_stm32g0.
 
+config UCSI_PMIC_GLINK
+	tristate "UCSI Qualcomm PMIC GLINK Interface Driver"
+	depends on QCOM_PMIC_GLINK
+	help
+	  This driver enables UCSI support on platforms that expose UCSI
+	  interface as PMIC GLINK device.
+
+	  To compile the driver as a module, choose M here: the module will be
+	  called ucsi_glink.
+
 endif
diff --git a/drivers/usb/typec/ucsi/Makefile b/drivers/usb/typec/ucsi/Makefile
index 480d533d762f..77f09e136956 100644
--- a/drivers/usb/typec/ucsi/Makefile
+++ b/drivers/usb/typec/ucsi/Makefile
@@ -18,3 +18,4 @@ endif
 obj-$(CONFIG_UCSI_ACPI)			+= ucsi_acpi.o
 obj-$(CONFIG_UCSI_CCG)			+= ucsi_ccg.o
 obj-$(CONFIG_UCSI_STM32G0)		+= ucsi_stm32g0.o
+obj-$(CONFIG_UCSI_PMIC_GLINK)		+= ucsi_glink.o
diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
new file mode 100644
index 000000000000..b454a5159896
--- /dev/null
+++ b/drivers/usb/typec/ucsi/ucsi_glink.c
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Linaro Ltd
+ */
+#include <linux/auxiliary_bus.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/mutex.h>
+#include <linux/property.h>
+#include <linux/soc/qcom/pdr.h>
+#include <linux/soc/qcom/pmic_glink.h>
+#include "ucsi.h"
+
+#define UCSI_BUF_SIZE                   48
+
+#define MSG_TYPE_REQ_RESP               1
+#define UCSI_BUF_SIZE                   48
+
+#define UC_NOTIFY_RECEIVER_UCSI         0x0
+#define UC_UCSI_READ_BUF_REQ            0x11
+#define UC_UCSI_WRITE_BUF_REQ           0x12
+#define UC_UCSI_USBC_NOTIFY_IND         0x13
+
+struct ucsi_read_buf_req_msg {
+	struct pmic_glink_hdr   hdr;
+};
+
+struct ucsi_read_buf_resp_msg {
+	struct pmic_glink_hdr   hdr;
+	u8                      buf[UCSI_BUF_SIZE];
+	u32                     ret_code;
+};
+
+struct ucsi_write_buf_req_msg {
+	struct pmic_glink_hdr   hdr;
+	u8                      buf[UCSI_BUF_SIZE];
+	u32                     reserved;
+};
+
+struct ucsi_write_buf_resp_msg {
+	struct pmic_glink_hdr   hdr;
+	u32                     ret_code;
+};
+
+struct ucsi_notify_ind_msg {
+	struct pmic_glink_hdr   hdr;
+	u32                     notification;
+	u32                     receiver;
+	u32                     reserved;
+};
+
+struct pmic_glink_ucsi {
+	struct device *dev;
+
+	struct pmic_glink_client *client;
+
+	struct ucsi *ucsi;
+	struct completion read_ack;
+	struct completion write_ack;
+	struct completion sync_ack;
+	bool sync_pending;
+	struct mutex lock;	/* protects concurrent access to PMIC Glink interface */
+
+	int sync_val;
+
+	struct work_struct notify_work;
+	struct work_struct register_work;
+
+	u8 read_buf[UCSI_BUF_SIZE];
+};
+
+static int pmic_glink_ucsi_read(struct ucsi *__ucsi, unsigned int offset,
+				void *val, size_t val_len)
+{
+	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+	struct ucsi_read_buf_req_msg req = {};
+	unsigned long left;
+	int ret;
+
+	req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+	req.hdr.type = MSG_TYPE_REQ_RESP;
+	req.hdr.opcode = UC_UCSI_READ_BUF_REQ;
+
+	mutex_lock(&ucsi->lock);
+	memset(ucsi->read_buf, 0, sizeof(ucsi->read_buf));
+	reinit_completion(&ucsi->read_ack);
+
+	ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+	if (ret < 0) {
+		dev_err(ucsi->dev, "failed to send UCSI read request: %d\n", ret);
+		goto out_unlock;
+	}
+
+	left = wait_for_completion_timeout(&ucsi->read_ack, 5 * HZ);
+	if (!left) {
+		dev_err(ucsi->dev, "timeout waiting for UCSI read response\n");
+		ret = -ETIMEDOUT;
+		goto out_unlock;
+	}
+
+	memcpy(val, &ucsi->read_buf[offset], val_len);
+	ret = 0;
+
+out_unlock:
+	mutex_unlock(&ucsi->lock);
+
+	return ret;
+}
+
+static int pmic_glink_ucsi_locked_write(struct pmic_glink_ucsi *ucsi, unsigned int offset,
+					const void *val, size_t val_len)
+{
+	struct ucsi_write_buf_req_msg req = {};
+	unsigned long left;
+	int ret;
+
+	req.hdr.owner = PMIC_GLINK_OWNER_USBC;
+	req.hdr.type = MSG_TYPE_REQ_RESP;
+	req.hdr.opcode = UC_UCSI_WRITE_BUF_REQ;
+	memcpy(&req.buf[offset], val, val_len);
+
+	reinit_completion(&ucsi->write_ack);
+
+	ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
+	if (ret < 0) {
+		dev_err(ucsi->dev, "failed to send UCSI write request: %d\n", ret);
+		return ret;
+	}
+
+	left = wait_for_completion_timeout(&ucsi->write_ack, 5 * HZ);
+	if (!left) {
+		dev_err(ucsi->dev, "timeout waiting for UCSI write response\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int pmic_glink_ucsi_async_write(struct ucsi *__ucsi, unsigned int offset,
+				       const void *val, size_t val_len)
+{
+	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+	int ret;
+
+	mutex_lock(&ucsi->lock);
+	ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+	mutex_unlock(&ucsi->lock);
+
+	return ret;
+}
+
+static int pmic_glink_ucsi_sync_write(struct ucsi *__ucsi, unsigned int offset,
+				      const void *val, size_t val_len)
+{
+	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
+	unsigned long left;
+	int ret;
+
+	/* TOFIX: Downstream forces recipient to CON when UCSI_GET_ALTERNATE_MODES command */
+
+	mutex_lock(&ucsi->lock);
+	ucsi->sync_val = 0;
+	reinit_completion(&ucsi->sync_ack);
+	ucsi->sync_pending = true;
+	ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
+	mutex_unlock(&ucsi->lock);
+
+	left = wait_for_completion_timeout(&ucsi->sync_ack, 5 * HZ);
+	if (!left) {
+		dev_err(ucsi->dev, "timeout waiting for UCSI sync write response\n");
+		ret = -ETIMEDOUT;
+	} else if (ucsi->sync_val) {
+		dev_err(ucsi->dev, "sync write returned: %d\n", ucsi->sync_val);
+	}
+
+	ucsi->sync_pending = false;
+
+	return ret;
+}
+
+static const struct ucsi_operations pmic_glink_ucsi_ops = {
+	.read = pmic_glink_ucsi_read,
+	.sync_write = pmic_glink_ucsi_sync_write,
+	.async_write = pmic_glink_ucsi_async_write
+};
+
+static void pmic_glink_ucsi_read_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+	const struct ucsi_read_buf_resp_msg *resp = data;
+
+	if (resp->ret_code)
+		return;
+
+	memcpy(ucsi->read_buf, resp->buf, UCSI_BUF_SIZE);
+	complete(&ucsi->read_ack);
+}
+
+static void pmic_glink_ucsi_write_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
+{
+	const struct ucsi_write_buf_resp_msg *resp = data;
+
+	if (resp->ret_code)
+		return;
+
+	ucsi->sync_val = resp->ret_code;
+	complete(&ucsi->write_ack);
+}
+
+static void pmic_glink_ucsi_notify(struct work_struct *work)
+{
+	struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, notify_work);
+	unsigned int con_num;
+	u32 cci;
+	int ret;
+
+	ret = pmic_glink_ucsi_read(ucsi->ucsi, UCSI_CCI, &cci, sizeof(cci));
+	if (ret) {
+		dev_err(ucsi->dev, "failed to read CCI on notification\n");
+		return;
+	}
+
+	con_num = UCSI_CCI_CONNECTOR(cci);
+	if (con_num)
+		ucsi_connector_change(ucsi->ucsi, con_num);
+
+	if (ucsi->sync_pending && cci & UCSI_CCI_BUSY) {
+		ucsi->sync_val = -EBUSY;
+		complete(&ucsi->sync_ack);
+	} else if (ucsi->sync_pending &&
+		   (cci & (UCSI_CCI_ACK_COMPLETE | UCSI_CCI_COMMAND_COMPLETE))) {
+		complete(&ucsi->sync_ack);
+	}
+}
+
+static void pmic_glink_ucsi_register(struct work_struct *work)
+{
+	struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, register_work);
+
+	ucsi_register(ucsi->ucsi);
+}
+
+static void pmic_glink_ucsi_callback(const void *data, size_t len, void *priv)
+{
+	struct pmic_glink_ucsi *ucsi = priv;
+	const struct pmic_glink_hdr *hdr = data;
+
+	switch (hdr->opcode) {
+	case UC_UCSI_READ_BUF_REQ:
+		pmic_glink_ucsi_read_ack(ucsi, data, len);
+		break;
+	case UC_UCSI_WRITE_BUF_REQ:
+		pmic_glink_ucsi_write_ack(ucsi, data, len);
+		break;
+	case UC_UCSI_USBC_NOTIFY_IND:
+		schedule_work(&ucsi->notify_work);
+		break;
+	};
+}
+
+static void pmic_glink_ucsi_pdr_notify(void *priv, int state)
+{
+	struct pmic_glink_ucsi *ucsi = priv;
+
+	if (state == SERVREG_SERVICE_STATE_UP)
+		schedule_work(&ucsi->register_work);
+	else if (state == SERVREG_SERVICE_STATE_DOWN)
+		ucsi_unregister(ucsi->ucsi);
+}
+
+static void pmic_glink_ucsi_destroy(void *data)
+{
+	struct pmic_glink_ucsi *ucsi = data;
+
+	/* Protect to make sure we're not in a middle of a transaction from a glink callback */
+	mutex_lock(&ucsi->lock);
+	ucsi_destroy(ucsi->ucsi);
+	mutex_unlock(&ucsi->lock);
+}
+
+static int pmic_glink_ucsi_probe(struct auxiliary_device *adev,
+				 const struct auxiliary_device_id *id)
+{
+	struct pmic_glink_ucsi *ucsi;
+	struct device *dev = &adev->dev;
+	int ret;
+
+	ucsi = devm_kzalloc(dev, sizeof(*ucsi), GFP_KERNEL);
+	if (!ucsi)
+		return -ENOMEM;
+
+	ucsi->dev = dev;
+	dev_set_drvdata(dev, ucsi);
+
+	INIT_WORK(&ucsi->notify_work, pmic_glink_ucsi_notify);
+	INIT_WORK(&ucsi->register_work, pmic_glink_ucsi_register);
+	init_completion(&ucsi->read_ack);
+	init_completion(&ucsi->write_ack);
+	init_completion(&ucsi->sync_ack);
+	mutex_init(&ucsi->lock);
+
+	ucsi->ucsi = ucsi_create(dev, &pmic_glink_ucsi_ops);
+	if (IS_ERR(ucsi->ucsi))
+		return PTR_ERR(ucsi->ucsi);
+
+	/* Make sure we destroy *after* pmic_glink unregister */
+	ret = devm_add_action_or_reset(dev, pmic_glink_ucsi_destroy, ucsi);
+	if (ret)
+		return ret;
+
+	ucsi_set_drvdata(ucsi->ucsi, ucsi);
+
+	ucsi->client = devm_pmic_glink_register_client(dev,
+						       PMIC_GLINK_OWNER_USBC,
+						       pmic_glink_ucsi_callback,
+						       pmic_glink_ucsi_pdr_notify,
+						       ucsi);
+	return PTR_ERR_OR_ZERO(ucsi->client);
+}
+
+static void pmic_glink_ucsi_remove(struct auxiliary_device *adev)
+{
+	struct pmic_glink_ucsi *ucsi = dev_get_drvdata(&adev->dev);
+
+	/* Unregister first to stop having read & writes */
+	ucsi_unregister(ucsi->ucsi);
+}
+
+static const struct auxiliary_device_id pmic_glink_ucsi_id_table[] = {
+	{ .name = "pmic_glink.ucsi", },
+	{},
+};
+MODULE_DEVICE_TABLE(auxiliary, pmic_glink_ucsi_id_table);
+
+static struct auxiliary_driver pmic_glink_ucsi_driver = {
+	.name = "pmic_glink_ucsi",
+	.probe = pmic_glink_ucsi_probe,
+	.remove = pmic_glink_ucsi_remove,
+	.id_table = pmic_glink_ucsi_id_table,
+};
+
+module_auxiliary_driver(pmic_glink_ucsi_driver);
+
+MODULE_DESCRIPTION("Qualcomm PMIC GLINK UCSI driver");
+MODULE_LICENSE("GPL");

-- 
2.34.1

Re: [PATCH v4 01/12] usb: typec: ucsi: add PMIC Glink UCSI driver

[Heikki Krogerus]

On Fri, Mar 17, 2023 at 04:04:17PM +0100, Neil Armstrong wrote:
> Introduce the UCSI PMIC Glink aux driver that communicates
> with the aDSP firmware with the UCSI protocol which handles
> the USB-C Port(s) Power Delivery.
> 
> The UCSI messaging is necessary on newer Qualcomm SoCs to
> provide USB role switch and altmode notifications.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> ---
>  drivers/usb/typec/ucsi/Kconfig      |  10 ++
>  drivers/usb/typec/ucsi/Makefile     |   1 +
>  drivers/usb/typec/ucsi/ucsi_glink.c | 345 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 356 insertions(+)
> 
> diff --git a/drivers/usb/typec/ucsi/Kconfig b/drivers/usb/typec/ucsi/Kconfig
> index 8f9c4b9f31f7..b3bb0191987e 100644
> --- a/drivers/usb/typec/ucsi/Kconfig
> +++ b/drivers/usb/typec/ucsi/Kconfig
> @@ -58,4 +58,14 @@ config UCSI_STM32G0
>  	  To compile the driver as a module, choose M here: the module will be
>  	  called ucsi_stm32g0.
>  
> +config UCSI_PMIC_GLINK
> +	tristate "UCSI Qualcomm PMIC GLINK Interface Driver"
> +	depends on QCOM_PMIC_GLINK
> +	help
> +	  This driver enables UCSI support on platforms that expose UCSI
> +	  interface as PMIC GLINK device.
> +
> +	  To compile the driver as a module, choose M here: the module will be
> +	  called ucsi_glink.
> +
>  endif
> diff --git a/drivers/usb/typec/ucsi/Makefile b/drivers/usb/typec/ucsi/Makefile
> index 480d533d762f..77f09e136956 100644
> --- a/drivers/usb/typec/ucsi/Makefile
> +++ b/drivers/usb/typec/ucsi/Makefile
> @@ -18,3 +18,4 @@ endif
>  obj-$(CONFIG_UCSI_ACPI)			+= ucsi_acpi.o
>  obj-$(CONFIG_UCSI_CCG)			+= ucsi_ccg.o
>  obj-$(CONFIG_UCSI_STM32G0)		+= ucsi_stm32g0.o
> +obj-$(CONFIG_UCSI_PMIC_GLINK)		+= ucsi_glink.o
> diff --git a/drivers/usb/typec/ucsi/ucsi_glink.c b/drivers/usb/typec/ucsi/ucsi_glink.c
> new file mode 100644
> index 000000000000..b454a5159896
> --- /dev/null
> +++ b/drivers/usb/typec/ucsi/ucsi_glink.c
> @@ -0,0 +1,345 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2019-2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2023, Linaro Ltd
> + */
> +#include <linux/auxiliary_bus.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/mutex.h>
> +#include <linux/property.h>
> +#include <linux/soc/qcom/pdr.h>
> +#include <linux/soc/qcom/pmic_glink.h>
> +#include "ucsi.h"
> +
> +#define UCSI_BUF_SIZE                   48
> +
> +#define MSG_TYPE_REQ_RESP               1
> +#define UCSI_BUF_SIZE                   48
> +
> +#define UC_NOTIFY_RECEIVER_UCSI         0x0
> +#define UC_UCSI_READ_BUF_REQ            0x11
> +#define UC_UCSI_WRITE_BUF_REQ           0x12
> +#define UC_UCSI_USBC_NOTIFY_IND         0x13
> +
> +struct ucsi_read_buf_req_msg {
> +	struct pmic_glink_hdr   hdr;
> +};
> +
> +struct ucsi_read_buf_resp_msg {
> +	struct pmic_glink_hdr   hdr;
> +	u8                      buf[UCSI_BUF_SIZE];
> +	u32                     ret_code;
> +};
> +
> +struct ucsi_write_buf_req_msg {
> +	struct pmic_glink_hdr   hdr;
> +	u8                      buf[UCSI_BUF_SIZE];
> +	u32                     reserved;
> +};
> +
> +struct ucsi_write_buf_resp_msg {
> +	struct pmic_glink_hdr   hdr;
> +	u32                     ret_code;
> +};
> +
> +struct ucsi_notify_ind_msg {
> +	struct pmic_glink_hdr   hdr;
> +	u32                     notification;
> +	u32                     receiver;
> +	u32                     reserved;
> +};
> +
> +struct pmic_glink_ucsi {
> +	struct device *dev;
> +
> +	struct pmic_glink_client *client;
> +
> +	struct ucsi *ucsi;
> +	struct completion read_ack;
> +	struct completion write_ack;
> +	struct completion sync_ack;
> +	bool sync_pending;
> +	struct mutex lock;	/* protects concurrent access to PMIC Glink interface */
> +
> +	int sync_val;
> +
> +	struct work_struct notify_work;
> +	struct work_struct register_work;
> +
> +	u8 read_buf[UCSI_BUF_SIZE];
> +};
> +
> +static int pmic_glink_ucsi_read(struct ucsi *__ucsi, unsigned int offset,
> +				void *val, size_t val_len)
> +{
> +	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
> +	struct ucsi_read_buf_req_msg req = {};
> +	unsigned long left;
> +	int ret;
> +
> +	req.hdr.owner = PMIC_GLINK_OWNER_USBC;
> +	req.hdr.type = MSG_TYPE_REQ_RESP;
> +	req.hdr.opcode = UC_UCSI_READ_BUF_REQ;
> +
> +	mutex_lock(&ucsi->lock);
> +	memset(ucsi->read_buf, 0, sizeof(ucsi->read_buf));
> +	reinit_completion(&ucsi->read_ack);
> +
> +	ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
> +	if (ret < 0) {
> +		dev_err(ucsi->dev, "failed to send UCSI read request: %d\n", ret);
> +		goto out_unlock;
> +	}
> +
> +	left = wait_for_completion_timeout(&ucsi->read_ack, 5 * HZ);
> +	if (!left) {
> +		dev_err(ucsi->dev, "timeout waiting for UCSI read response\n");
> +		ret = -ETIMEDOUT;
> +		goto out_unlock;
> +	}
> +
> +	memcpy(val, &ucsi->read_buf[offset], val_len);
> +	ret = 0;
> +
> +out_unlock:
> +	mutex_unlock(&ucsi->lock);
> +
> +	return ret;
> +}
> +
> +static int pmic_glink_ucsi_locked_write(struct pmic_glink_ucsi *ucsi, unsigned int offset,
> +					const void *val, size_t val_len)
> +{
> +	struct ucsi_write_buf_req_msg req = {};
> +	unsigned long left;
> +	int ret;
> +
> +	req.hdr.owner = PMIC_GLINK_OWNER_USBC;
> +	req.hdr.type = MSG_TYPE_REQ_RESP;
> +	req.hdr.opcode = UC_UCSI_WRITE_BUF_REQ;
> +	memcpy(&req.buf[offset], val, val_len);
> +
> +	reinit_completion(&ucsi->write_ack);
> +
> +	ret = pmic_glink_send(ucsi->client, &req, sizeof(req));
> +	if (ret < 0) {
> +		dev_err(ucsi->dev, "failed to send UCSI write request: %d\n", ret);
> +		return ret;
> +	}
> +
> +	left = wait_for_completion_timeout(&ucsi->write_ack, 5 * HZ);
> +	if (!left) {
> +		dev_err(ucsi->dev, "timeout waiting for UCSI write response\n");
> +		return -ETIMEDOUT;
> +	}
> +
> +	return 0;
> +}
> +
> +static int pmic_glink_ucsi_async_write(struct ucsi *__ucsi, unsigned int offset,
> +				       const void *val, size_t val_len)
> +{
> +	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
> +	int ret;
> +
> +	mutex_lock(&ucsi->lock);
> +	ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
> +	mutex_unlock(&ucsi->lock);
> +
> +	return ret;
> +}
> +
> +static int pmic_glink_ucsi_sync_write(struct ucsi *__ucsi, unsigned int offset,
> +				      const void *val, size_t val_len)
> +{
> +	struct pmic_glink_ucsi *ucsi = ucsi_get_drvdata(__ucsi);
> +	unsigned long left;
> +	int ret;
> +
> +	/* TOFIX: Downstream forces recipient to CON when UCSI_GET_ALTERNATE_MODES command */
> +
> +	mutex_lock(&ucsi->lock);
> +	ucsi->sync_val = 0;
> +	reinit_completion(&ucsi->sync_ack);
> +	ucsi->sync_pending = true;
> +	ret = pmic_glink_ucsi_locked_write(ucsi, offset, val, val_len);
> +	mutex_unlock(&ucsi->lock);
> +
> +	left = wait_for_completion_timeout(&ucsi->sync_ack, 5 * HZ);
> +	if (!left) {
> +		dev_err(ucsi->dev, "timeout waiting for UCSI sync write response\n");
> +		ret = -ETIMEDOUT;
> +	} else if (ucsi->sync_val) {
> +		dev_err(ucsi->dev, "sync write returned: %d\n", ucsi->sync_val);
> +	}
> +
> +	ucsi->sync_pending = false;
> +
> +	return ret;
> +}
> +
> +static const struct ucsi_operations pmic_glink_ucsi_ops = {
> +	.read = pmic_glink_ucsi_read,
> +	.sync_write = pmic_glink_ucsi_sync_write,
> +	.async_write = pmic_glink_ucsi_async_write
> +};
> +
> +static void pmic_glink_ucsi_read_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
> +{
> +	const struct ucsi_read_buf_resp_msg *resp = data;
> +
> +	if (resp->ret_code)
> +		return;
> +
> +	memcpy(ucsi->read_buf, resp->buf, UCSI_BUF_SIZE);
> +	complete(&ucsi->read_ack);
> +}
> +
> +static void pmic_glink_ucsi_write_ack(struct pmic_glink_ucsi *ucsi, const void *data, int len)
> +{
> +	const struct ucsi_write_buf_resp_msg *resp = data;
> +
> +	if (resp->ret_code)
> +		return;
> +
> +	ucsi->sync_val = resp->ret_code;
> +	complete(&ucsi->write_ack);
> +}
> +
> +static void pmic_glink_ucsi_notify(struct work_struct *work)
> +{
> +	struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, notify_work);
> +	unsigned int con_num;
> +	u32 cci;
> +	int ret;
> +
> +	ret = pmic_glink_ucsi_read(ucsi->ucsi, UCSI_CCI, &cci, sizeof(cci));
> +	if (ret) {
> +		dev_err(ucsi->dev, "failed to read CCI on notification\n");
> +		return;
> +	}
> +
> +	con_num = UCSI_CCI_CONNECTOR(cci);
> +	if (con_num)
> +		ucsi_connector_change(ucsi->ucsi, con_num);
> +
> +	if (ucsi->sync_pending && cci & UCSI_CCI_BUSY) {
> +		ucsi->sync_val = -EBUSY;
> +		complete(&ucsi->sync_ack);
> +	} else if (ucsi->sync_pending &&
> +		   (cci & (UCSI_CCI_ACK_COMPLETE | UCSI_CCI_COMMAND_COMPLETE))) {
> +		complete(&ucsi->sync_ack);
> +	}
> +}
> +
> +static void pmic_glink_ucsi_register(struct work_struct *work)
> +{
> +	struct pmic_glink_ucsi *ucsi = container_of(work, struct pmic_glink_ucsi, register_work);
> +
> +	ucsi_register(ucsi->ucsi);
> +}
> +
> +static void pmic_glink_ucsi_callback(const void *data, size_t len, void *priv)
> +{
> +	struct pmic_glink_ucsi *ucsi = priv;
> +	const struct pmic_glink_hdr *hdr = data;
> +
> +	switch (hdr->opcode) {
> +	case UC_UCSI_READ_BUF_REQ:
> +		pmic_glink_ucsi_read_ack(ucsi, data, len);
> +		break;
> +	case UC_UCSI_WRITE_BUF_REQ:
> +		pmic_glink_ucsi_write_ack(ucsi, data, len);
> +		break;
> +	case UC_UCSI_USBC_NOTIFY_IND:
> +		schedule_work(&ucsi->notify_work);
> +		break;
> +	};
> +}
> +
> +static void pmic_glink_ucsi_pdr_notify(void *priv, int state)
> +{
> +	struct pmic_glink_ucsi *ucsi = priv;
> +
> +	if (state == SERVREG_SERVICE_STATE_UP)
> +		schedule_work(&ucsi->register_work);
> +	else if (state == SERVREG_SERVICE_STATE_DOWN)
> +		ucsi_unregister(ucsi->ucsi);
> +}
> +
> +static void pmic_glink_ucsi_destroy(void *data)
> +{
> +	struct pmic_glink_ucsi *ucsi = data;
> +
> +	/* Protect to make sure we're not in a middle of a transaction from a glink callback */
> +	mutex_lock(&ucsi->lock);
> +	ucsi_destroy(ucsi->ucsi);
> +	mutex_unlock(&ucsi->lock);
> +}
> +
> +static int pmic_glink_ucsi_probe(struct auxiliary_device *adev,
> +				 const struct auxiliary_device_id *id)
> +{
> +	struct pmic_glink_ucsi *ucsi;
> +	struct device *dev = &adev->dev;
> +	int ret;
> +
> +	ucsi = devm_kzalloc(dev, sizeof(*ucsi), GFP_KERNEL);
> +	if (!ucsi)
> +		return -ENOMEM;
> +
> +	ucsi->dev = dev;
> +	dev_set_drvdata(dev, ucsi);
> +
> +	INIT_WORK(&ucsi->notify_work, pmic_glink_ucsi_notify);
> +	INIT_WORK(&ucsi->register_work, pmic_glink_ucsi_register);
> +	init_completion(&ucsi->read_ack);
> +	init_completion(&ucsi->write_ack);
> +	init_completion(&ucsi->sync_ack);
> +	mutex_init(&ucsi->lock);
> +
> +	ucsi->ucsi = ucsi_create(dev, &pmic_glink_ucsi_ops);
> +	if (IS_ERR(ucsi->ucsi))
> +		return PTR_ERR(ucsi->ucsi);
> +
> +	/* Make sure we destroy *after* pmic_glink unregister */
> +	ret = devm_add_action_or_reset(dev, pmic_glink_ucsi_destroy, ucsi);
> +	if (ret)
> +		return ret;
> +
> +	ucsi_set_drvdata(ucsi->ucsi, ucsi);
> +
> +	ucsi->client = devm_pmic_glink_register_client(dev,
> +						       PMIC_GLINK_OWNER_USBC,
> +						       pmic_glink_ucsi_callback,
> +						       pmic_glink_ucsi_pdr_notify,
> +						       ucsi);
> +	return PTR_ERR_OR_ZERO(ucsi->client);
> +}
> +
> +static void pmic_glink_ucsi_remove(struct auxiliary_device *adev)
> +{
> +	struct pmic_glink_ucsi *ucsi = dev_get_drvdata(&adev->dev);
> +
> +	/* Unregister first to stop having read & writes */
> +	ucsi_unregister(ucsi->ucsi);
> +}
> +
> +static const struct auxiliary_device_id pmic_glink_ucsi_id_table[] = {
> +	{ .name = "pmic_glink.ucsi", },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(auxiliary, pmic_glink_ucsi_id_table);
> +
> +static struct auxiliary_driver pmic_glink_ucsi_driver = {
> +	.name = "pmic_glink_ucsi",
> +	.probe = pmic_glink_ucsi_probe,
> +	.remove = pmic_glink_ucsi_remove,
> +	.id_table = pmic_glink_ucsi_id_table,
> +};
> +
> +module_auxiliary_driver(pmic_glink_ucsi_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm PMIC GLINK UCSI driver");
> +MODULE_LICENSE("GPL");

thanks,

-- 
heikki

[PATCH v4 02/12] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8450 compatible

[Neil Armstrong]

Document the SM8450 compatible used to describe the pmic glink
on this platform.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index cf863683c21a..a85bc14de065 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -25,6 +25,7 @@ properties:
           - qcom,sc8180x-pmic-glink
           - qcom,sc8280xp-pmic-glink
           - qcom,sm8350-pmic-glink
+          - qcom,sm8450-pmic-glink
       - const: qcom,pmic-glink
 
   '#address-cells':

-- 
2.34.1

[PATCH v4 03/12] dt-bindings: soc: qcom: qcom,pmic-glink: document SM8550 compatible

[Neil Armstrong]

Document the SM8550 compatible used to describe the pmic glink
on this platform.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
index a85bc14de065..6440dc801387 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,pmic-glink.yaml
@@ -26,6 +26,7 @@ properties:
           - qcom,sc8280xp-pmic-glink
           - qcom,sm8350-pmic-glink
           - qcom,sm8450-pmic-glink
+          - qcom,sm8550-pmic-glink
       - const: qcom,pmic-glink
 
   '#address-cells':

-- 
2.34.1

[PATCH v4 04/12] soc: qcom: pmic_glink: register ucsi aux device

[Neil Armstrong]

Only register UCSI on know working devices, like on the SM8450
or SM8550 which requires UCSI to get USB mode switch events.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 drivers/soc/qcom/pmic_glink.c | 65 +++++++++++++++++++++++++++++++++++--------
 1 file changed, 54 insertions(+), 11 deletions(-)

diff --git a/drivers/soc/qcom/pmic_glink.c b/drivers/soc/qcom/pmic_glink.c
index bb3fb57abcc6..8bf95df0a56a 100644
--- a/drivers/soc/qcom/pmic_glink.c
+++ b/drivers/soc/qcom/pmic_glink.c
@@ -4,6 +4,7 @@
  * Copyright (c) 2022, Linaro Ltd
  */
 #include <linux/auxiliary_bus.h>
+#include <linux/of_device.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/rpmsg.h>
@@ -11,12 +12,23 @@
 #include <linux/soc/qcom/pdr.h>
 #include <linux/soc/qcom/pmic_glink.h>
 
+enum {
+	PMIC_GLINK_CLIENT_BATT = 0,
+	PMIC_GLINK_CLIENT_ALTMODE,
+	PMIC_GLINK_CLIENT_UCSI,
+};
+
+#define PMIC_GLINK_CLIENT_DEFAULT	(BIT(PMIC_GLINK_CLIENT_BATT) |	\
+					 BIT(PMIC_GLINK_CLIENT_ALTMODE))
+
 struct pmic_glink {
 	struct device *dev;
 	struct pdr_handle *pdr;
 
 	struct rpmsg_endpoint *ept;
 
+	unsigned long client_mask;
+
 	struct auxiliary_device altmode_aux;
 	struct auxiliary_device ps_aux;
 	struct auxiliary_device ucsi_aux;
@@ -233,6 +245,7 @@ static struct rpmsg_driver pmic_glink_rpmsg_driver = {
 
 static int pmic_glink_probe(struct platform_device *pdev)
 {
+	const unsigned long *match_data;
 	struct pdr_service *service;
 	struct pmic_glink *pg;
 	int ret;
@@ -249,12 +262,27 @@ static int pmic_glink_probe(struct platform_device *pdev)
 	mutex_init(&pg->client_lock);
 	mutex_init(&pg->state_lock);
 
-	ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
-	if (ret)
-		return ret;
-	ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
-	if (ret)
-		goto out_release_altmode_aux;
+	match_data = (unsigned long *)of_device_get_match_data(&pdev->dev);
+	if (match_data)
+		pg->client_mask = *match_data;
+	else
+		pg->client_mask = PMIC_GLINK_CLIENT_DEFAULT;
+
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI)) {
+		ret = pmic_glink_add_aux_device(pg, &pg->ucsi_aux, "ucsi");
+		if (ret)
+			return ret;
+	}
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE)) {
+		ret = pmic_glink_add_aux_device(pg, &pg->altmode_aux, "altmode");
+		if (ret)
+			goto out_release_ucsi_aux;
+	}
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT)) {
+		ret = pmic_glink_add_aux_device(pg, &pg->ps_aux, "power-supply");
+		if (ret)
+			goto out_release_altmode_aux;
+	}
 
 	pg->pdr = pdr_handle_alloc(pmic_glink_pdr_callback, pg);
 	if (IS_ERR(pg->pdr)) {
@@ -278,9 +306,14 @@ static int pmic_glink_probe(struct platform_device *pdev)
 out_release_pdr_handle:
 	pdr_handle_release(pg->pdr);
 out_release_aux_devices:
-	pmic_glink_del_aux_device(pg, &pg->ps_aux);
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+		pmic_glink_del_aux_device(pg, &pg->ps_aux);
 out_release_altmode_aux:
-	pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+		pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+out_release_ucsi_aux:
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+		pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
 
 	return ret;
 }
@@ -291,8 +324,12 @@ static int pmic_glink_remove(struct platform_device *pdev)
 
 	pdr_handle_release(pg->pdr);
 
-	pmic_glink_del_aux_device(pg, &pg->ps_aux);
-	pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_BATT))
+		pmic_glink_del_aux_device(pg, &pg->ps_aux);
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_ALTMODE))
+		pmic_glink_del_aux_device(pg, &pg->altmode_aux);
+	if (pg->client_mask & BIT(PMIC_GLINK_CLIENT_UCSI))
+		pmic_glink_del_aux_device(pg, &pg->ucsi_aux);
 
 	mutex_lock(&__pmic_glink_lock);
 	__pmic_glink = NULL;
@@ -301,8 +338,14 @@ static int pmic_glink_remove(struct platform_device *pdev)
 	return 0;
 }
 
+/* Do not handle altmode for now on those platforms */
+static const unsigned long pmic_glink_sm8450_client_mask = BIT(PMIC_GLINK_CLIENT_BATT) |
+							   BIT(PMIC_GLINK_CLIENT_UCSI);
+
 static const struct of_device_id pmic_glink_of_match[] = {
-	{ .compatible = "qcom,pmic-glink", },
+	{ .compatible = "qcom,sm8450-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+	{ .compatible = "qcom,sm8550-pmic-glink", .data = &pmic_glink_sm8450_client_mask },
+	{ .compatible = "qcom,pmic-glink" },
 	{}
 };
 MODULE_DEVICE_TABLE(of, pmic_glink_of_match);

-- 
2.34.1

[PATCH v4 05/12] dt-bindings: usb: snps,dwc3: document HS & SS OF graph ports

[Neil Armstrong]

Document the optional ports subnode to describe the High-Speed
and Super-Speed connections as separate OF graph links.

The ports property is an alternative to the already documented
single port subnode property.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 Documentation/devicetree/bindings/usb/snps,dwc3.yaml | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
index 16c7d06c9172..cce74c59bf0e 100644
--- a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -379,6 +379,22 @@ properties:
       This port is used with the 'usb-role-switch' property  to connect the
       dwc3 to type C connector.
 
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    description:
+      Those ports should be used with any connector to the data bus of this
+      controller using the OF graph bindings specified if the "usb-role-switch"
+      property is used.
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: High Speed (HS) data bus.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Super Speed (SS) data bus.
+
   wakeup-source:
     $ref: /schemas/types.yaml#/definitions/flag
     description:

-- 
2.34.1

[PATCH v4 06/12] arm64: dts: qcom: sm8350: add port subnodes in dwc3 node

[Neil Armstrong]

Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 1afc4311796e..6c3a82c63585 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2270,6 +2270,25 @@ usb_1_dwc3: usb@a600000 {
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+						};
+					};
+				};
 			};
 		};
 

-- 
2.34.1

[PATCH v4 07/12] arm64: dts: qcom: sm8450: add port subnodes in dwc3 node

[Neil Armstrong]

Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 69695eb83897..d92d49a1ca2c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -4170,6 +4170,25 @@ usb_1_dwc3: usb@a600000 {
 				snps,dis_enblslpm_quirk;
 				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+						};
+					};
+				};
 			};
 		};
 

-- 
2.34.1

[PATCH v4 08/12] arm64: dts: qcom: sm8550: add port subnodes in dwc3 node

[Neil Armstrong]

Add ports subnodes in dwc3 node to avoid repeating the
same description in each board DT.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 6af4079c9a35..da32f6bc34ab 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2460,6 +2460,25 @@ usb_1_dwc3: usb@a600000 {
 				phys = <&usb_1_hsphy>,
 				       <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
 				phy-names = "usb2-phy", "usb3-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						usb_1_dwc3_ss: endpoint {
+						};
+					};
+				};
 			};
 		};
 

-- 
2.34.1

[PATCH v4 09/12] arm64: dts: qcom: sm8350-hdk: add pmic glink node

[Neil Armstrong]

Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350-hdk.dts | 67 ++++++++++++++++++++++++++++++++-
 1 file changed, 65 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 09baf6959c71..01affb16d039 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -31,6 +31,40 @@ hdmi_con: endpoint {
 		};
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8350-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -674,8 +708,37 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	/* TODO: Define USB-C connector properly */
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			usb_1_dwc3_hs: endpoint {
+				remote-endpoint = <&pmic_glink_hs_in>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			usb_1_dwc3_ss: endpoint {
+				remote-endpoint = <&pmic_glink_ss_in>;
+			};
+		};
+	};
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&pmic_glink_ss_in>;
 };
 
 &usb_1_hsphy {

-- 
2.34.1

Re: [PATCH v4 09/12] arm64: dts: qcom: sm8350-hdk: add pmic glink node

[Konrad Dybcio]

On 17.03.2023 16:04, Neil Armstrong wrote:
> Add the pmic glink node linked with the DWC3 USB controller
> switched to OTG mode and tagged with usb-role-switch.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---

[...]

>  &usb_1_dwc3 {
> -	/* TODO: Define USB-C connector properly */
> -	dr_mode = "peripheral";
> +	dr_mode = "otg";
> +	usb-role-switch;
> +
> +	ports {
You created these in patch [6/12]!

Konrad
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		port@0 {
> +			reg = <0>;
> +
> +			usb_1_dwc3_hs: endpoint {
> +				remote-endpoint = <&pmic_glink_hs_in>;
> +			};
> +		};
> +
> +		port@1 {
> +			reg = <1>;
> +
> +			usb_1_dwc3_ss: endpoint {
> +				remote-endpoint = <&pmic_glink_ss_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&usb_1_dwc3_hs {
> +	remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_dwc3_ss {
> +	remote-endpoint = <&pmic_glink_ss_in>;
>  };
>  
>  &usb_1_hsphy {
> 

Re: [PATCH v4 09/12] arm64: dts: qcom: sm8350-hdk: add pmic glink node

[Neil Armstrong]

On 18/03/2023 15:00, Konrad Dybcio wrote:
> 
> 
> On 17.03.2023 16:04, Neil Armstrong wrote:
>> Add the pmic glink node linked with the DWC3 USB controller
>> switched to OTG mode and tagged with usb-role-switch.
>>
>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>> ---
> 
> [...]
> 
>>   &usb_1_dwc3 {
>> -	/* TODO: Define USB-C connector properly */
>> -	dr_mode = "peripheral";
>> +	dr_mode = "otg";
>> +	usb-role-switch;
>> +
>> +	ports {
> You created these in patch [6/12]!

Damn!

Thx!

Neil

> 
> Konrad
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		port@0 {
>> +			reg = <0>;
>> +
>> +			usb_1_dwc3_hs: endpoint {
>> +				remote-endpoint = <&pmic_glink_hs_in>;
>> +			};
>> +		};
>> +
>> +		port@1 {
>> +			reg = <1>;
>> +
>> +			usb_1_dwc3_ss: endpoint {
>> +				remote-endpoint = <&pmic_glink_ss_in>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&usb_1_dwc3_hs {
>> +	remote-endpoint = <&pmic_glink_hs_in>;
>> +};
>> +
>> +&usb_1_dwc3_ss {
>> +	remote-endpoint = <&pmic_glink_ss_in>;
>>   };
>>   
>>   &usb_1_hsphy {
>>

[PATCH v4 10/12] arm64: dts: qcom: sm8450-hdk: add pmic glink node

[Neil Armstrong]

Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450-hdk.dts | 45 ++++++++++++++++++++++++++++++++-
 1 file changed, 44 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
index feef3837e4cd..1755ee3aa04c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -87,6 +87,40 @@ lt9611_3v3: lt9611-3v3-regulator {
 		enable-active-high;
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -724,7 +758,16 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&pmic_glink_ss_in>;
 };
 
 &usb_1_hsphy {

-- 
2.34.1

[PATCH v4 11/12] arm64: dts: qcom: sm8550-mtp: add pmic glink node

[Neil Armstrong]

Add the pmic glink node linked with the DWC3 USB controller
switched to OTG mode and tagged with usb-role-switch.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550-mtp.dts | 45 ++++++++++++++++++++++++++++++++-
 1 file changed, 44 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
index 9d4ddb883a70..e2b9bb6b1e27 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-mtp.dts
@@ -27,6 +27,40 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_ss>;
+					};
+				};
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -561,7 +595,16 @@ &usb_1 {
 };
 
 &usb_1_dwc3 {
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	usb-role-switch;
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_dwc3_ss {
+	remote-endpoint = <&pmic_glink_ss_in>;
 };
 
 &usb_1_hsphy {

-- 
2.34.1

[PATCH v4 12/12] arm64: defconfig: add PMIC GLINK modules

[Neil Armstrong]

Enable the PMIC GLINK core, altmode, battery and UCSI
aux drivers as module to enable USB Type-C management
over the PMIC GLINK protocol on modern Qcom platforms.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
 arch/arm64/configs/defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 3a6d995384d9..d849fa2ca852 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -273,6 +273,10 @@ CONFIG_VIRTIO_BLK=y
 CONFIG_BLK_DEV_NVME=m
 CONFIG_QCOM_COINCELL=m
 CONFIG_QCOM_FASTRPC=m
+CONFIG_BATTERY_QCOM_BATTMGR=m
+CONFIG_QCOM_PMIC_GLINK=m
+CONFIG_TYPEC_UCSI=m
+CONFIG_UCSI_PMIC_GLINK=m
 CONFIG_SRAM=y
 CONFIG_PCI_ENDPOINT_TEST=m
 CONFIG_EEPROM_AT24=m

-- 
2.34.1