From: JC Kuo <jckuo@nvidia.com>
To: Nagarjuna Kristam <nkristam@nvidia.com>, <balbi@kernel.org>,
<gregkh@linuxfoundation.org>, <thierry.reding@gmail.com>,
<jonathanh@nvidia.com>, <mark.rutland@arm.com>,
<robh+dt@kernel.org>
Cc: <linux-tegra@vger.kernel.org>, <linux-usb@vger.kernel.org>,
<devicetree@vger.kernel.org>
Subject: Re: [Patch V3 4/8] dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding
Date: Tue, 21 May 2019 14:08:32 +0800 [thread overview]
Message-ID: <64954535-57fb-7444-306a-1a5a48dceeaf@nvidia.com> (raw)
In-Reply-To: <1557988772-15406-5-git-send-email-nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Thanks,
JC
On 5/16/19 2:39 PM, Nagarjuna Kristam wrote:
> Add device-tree binding documentation for the XUSB device mode controller
> present on Tegra210 SoC. This controller supports the USB 3.0
> specification.
>
> Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
> ---
> .../devicetree/bindings/usb/nvidia,tegra-xudc.txt | 101 +++++++++++++++++++++
> 1 file changed, 101 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
>
> diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
> new file mode 100644
> index 0000000..d78b436
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra-xudc.txt
> @@ -0,0 +1,101 @@
> +Device tree binding for NVIDIA Tegra XUSB device mode controller (XUDC)
> +=======================================================================
> +
> +The Tegra XUDC controller supports both USB 2.0 HighSpeed/FullSpeed and
> +USB 3.0 SuperSpeed protocols.
> +
> +Required properties:
> +--------------------
> +- compatible: For Tegra210, must contain "nvidia,tegra210-xudc".
> +- reg: Must contain the base and length of the XUSB device registers, XUSB device
> + PCI Config registers and XUSB device controller registers.
> +- interrupts: Must contain the XUSB device interrupt.
> +- clocks: Must contain an entry for all clocks used.
> + See ../clock/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - dev: Clock to enable core XUSB dev clock.
> + - ss: Clock to enable XUSB super speed clock.
> + - ss_src: Clock to enable XUSB super speed dev clock.
> + - hs_src: Clock to enable XUSB high Speed dev clock.
> + - fs_src: Clock to enable XUSB full Speed dev clock.
> +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to
> + configure the USB pads used by the XUDC controller.
> +- power-domains: A list of PM domain specifiers that reference each power-domain
> + used by the XUSB device mode controller. This list must comprise of a specifier
> + for the XUSBA and XUSBB power-domains. See ../power/power_domain.txt and
> + ../arm/tegra/nvidia,tegra20-pmc.txt for details.
> +- power-domain-names: A list of names that represent each of the specifiers in
> + the 'power-domains' property. Must include 'ss' and 'dev'.
> +
> +For Tegra210:
> +- avddio-usb-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V.
> +- hvdd-usb-supply: USB controller power supply. Must supply 3.3 V.
> +
> +- phys: Must contain an entry for each entry in phy-names.
> + See ../phy/phy-bindings.txt for details.
> +- phy-names: Should include an entry for each PHY used by the controller.
> + Names must be "usb2", and "usb3" if support SuperSpeed device mode.
> + - "usb3" phy, SuperSpeed (SSTX+/SSTX-/SSRX+/SSRX-) data lines.
> + - "usb2" phy, USB 2.0 (D+/D-) data lines.
> +
> +- extcon: Must contains an extcon entry which detects USB VBUS pin.
> + See ../extcon/extcon-usb-gpio.txt for details.
> +
> +Example:
> +--------
> + pmc: pmc@7000e400 {
> + compatible = "nvidia,tegra210-pmc";
> + reg = <0x0 0x7000e400 0x0 0x400>;
> + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
> + clock-names = "pclk", "clk32k_in";
> +
> + powergates {
> + pd_xusbss: xusba {
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
> + resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
> + #power-domain-cells = <0>;
> + };
> +
> + pd_xusbdev: xusbb {
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
> + resets = <&tegra_car 95>;
> + #power-domain-cells = <0>;
> + };
> + };
> + };
> +
> + xudc@700d0000 {
> + compatible = "nvidia,tegra210-xudc";
> + reg = <0x0 0x700d0000 0x0 0x8000>,
> + <0x0 0x700d8000 0x0 0x1000>,
> + <0x0 0x700d9000 0x0 0x1000>;
> +
> + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>,
> + <&tegra_car TEGRA210_CLK_XUSB_SS>,
> + <&tegra_car TEGRA210_CLK_XUSB_SSP_SRC>,
> + <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
> + <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>;
> + clock-names = "dev", "ss", "ss_src",
> + "hs_src", "fs_src";
> +
> + power-domains = <&pd_xusbdev>, <&pd_xusbss>;
> + power-domain-names = "dev", "ss";
> +
> + nvidia,xusb-padctl = <&padctl>;
> +
> + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>;
> + phy-names = "usb2;
> +
> + avddio-usb-supply = <&vdd_pex_1v05>;
> + hvdd-usb-supply = <&vdd_3v3_sys>;
> +
> + extcon = <&extcon_usb>;
> + };
> +
> + extcon_usb: extcon_vbus {
> + compatible = "linux,extcon-usb-gpio";
> + vbus-gpio = <&gpio TEGRA_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
> + };
> +
next prev parent reply other threads:[~2019-05-21 6:08 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-16 6:39 [Patch V3 0/8] Tegra XUSB gadget driver support Nagarjuna Kristam
2019-05-16 6:39 ` [Patch V3 1/8] phy: tegra: xusb: t210: add XUSB dual mode support Nagarjuna Kristam
2019-05-21 2:16 ` jckuo
2019-05-23 9:39 ` Thierry Reding
2019-05-16 6:39 ` [Patch V3 2/8] phy: tegra: xusb: t210: add usb3 port fake support Nagarjuna Kristam
2019-05-21 3:00 ` jckuo
2019-05-23 11:16 ` Nagarjuna Kristam
2019-05-23 10:01 ` Thierry Reding
2019-05-23 11:24 ` Nagarjuna Kristam
2019-05-16 6:39 ` [Patch V3 3/8] phy: tegra: xusb: t210: add vbus override support Nagarjuna Kristam
2019-05-21 4:34 ` jckuo
2019-05-23 11:15 ` Nagarjuna Kristam
2019-05-23 10:03 ` Thierry Reding
2019-05-23 11:13 ` Nagarjuna Kristam
2019-05-16 6:39 ` [Patch V3 4/8] dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding Nagarjuna Kristam
2019-05-21 6:08 ` JC Kuo [this message]
2019-05-23 10:13 ` Thierry Reding
2019-05-23 11:41 ` Nagarjuna Kristam
2019-06-13 21:32 ` Rob Herring
2019-06-18 6:18 ` Nagarjuna Kristam
2019-05-16 6:39 ` [Patch V3 5/8] arm64: tegra: Add xudc node for Tegra210 Nagarjuna Kristam
2019-05-21 6:08 ` JC Kuo
2019-05-23 10:15 ` Thierry Reding
2019-05-16 6:39 ` [Patch V3 6/8] arm64: tegra: Enable xudc on Jetson TX1 Nagarjuna Kristam
2019-05-21 6:11 ` JC Kuo
2019-05-16 6:39 ` [Patch V3 7/8] usb: gadget: Add UDC driver for tegra XUSB device mode controller Nagarjuna Kristam
2019-05-16 9:08 ` Chunfeng Yun
2019-05-24 6:50 ` Nagarjuna Kristam
2019-05-29 8:06 ` Chunfeng Yun
2019-05-23 10:26 ` Thierry Reding
2019-05-23 10:28 ` Thierry Reding
2019-05-16 6:39 ` [Patch V3 8/8] arm64: defconfig: Enable tegra XUDC driver Nagarjuna Kristam
2019-05-23 10:30 ` Thierry Reding
2019-05-24 8:01 ` Nagarjuna Kristam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=64954535-57fb-7444-306a-1a5a48dceeaf@nvidia.com \
--to=jckuo@nvidia.com \
--cc=balbi@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jonathanh@nvidia.com \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=nkristam@nvidia.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).