* [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
@ 2022-01-28 22:36 Adam Ford
2022-01-31 0:23 ` Yoshihiro Shimoda
0 siblings, 1 reply; 4+ messages in thread
From: Adam Ford @ 2022-01-28 22:36 UTC (permalink / raw)
To: linux-usb
Cc: linux-renesas-soc, cstevens, aford, Adam Ford, Felipe Balbi,
Greg Kroah-Hartman, Biju Das, Yoshihiro Shimoda, linux-kernel
The support the external role switch a variety of situations were
addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
leaves the host up which can cause some error messages when
switching from host to none, to gadget, to none, and then back
to host again.
xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
xhci-hcd ee000000.usb: HC died; cleaning up
usb 4-1: device not accepting address 6, error -108
usb usb4-port1: couldn't allocate usb_device
After this happens it will not act as a host again.
Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
Fixes: 0604160d8c0b ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
Signed-off-by: Adam Ford <aford173@gmail.com>
diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c
index 57d417a7c3e0..601829a6b4ba 100644
--- a/drivers/usb/gadget/udc/renesas_usb3.c
+++ b/drivers/usb/gadget/udc/renesas_usb3.c
@@ -2378,6 +2378,8 @@ static void handle_ext_role_switch_states(struct device *dev,
switch (role) {
case USB_ROLE_NONE:
usb3->connection_state = USB_ROLE_NONE;
+ if (cur_role == USB_ROLE_HOST)
+ device_release_driver(host);
if (usb3->driver)
usb3_disconnect(usb3);
usb3_vbus_out(usb3, false);
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* RE: [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
2022-01-28 22:36 [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition Adam Ford
@ 2022-01-31 0:23 ` Yoshihiro Shimoda
2022-01-31 1:01 ` Adam Ford
0 siblings, 1 reply; 4+ messages in thread
From: Yoshihiro Shimoda @ 2022-01-31 0:23 UTC (permalink / raw)
To: Adam Ford, linux-usb
Cc: linux-renesas-soc, cstevens, aford, Felipe Balbi,
Greg Kroah-Hartman, Biju Das, linux-kernel
Hi Adam-san,
Thank you for the patch!
> From: Adam Ford, Sent: Saturday, January 29, 2022 7:36 AM
>
> The support the external role switch a variety of situations were
> addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
> leaves the host up which can cause some error messages when
> switching from host to none, to gadget, to none, and then back
> to host again.
I think so. An external role switch in this driver is possible to
enter the role to USB_ROLE_NONE. (Just a record for me: in other words,
the "internal" role switch didn't enter the role to USB_ROLE_NONE.)
> xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
> xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
> xhci-hcd ee000000.usb: HC died; cleaning up
> usb 4-1: device not accepting address 6, error -108
> usb usb4-port1: couldn't allocate usb_device
>
> After this happens it will not act as a host again.
> Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
>
> Fixes: 0604160d8c0b ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
> Signed-off-by: Adam Ford <aford173@gmail.com>
>
> diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c
> index 57d417a7c3e0..601829a6b4ba 100644
> --- a/drivers/usb/gadget/udc/renesas_usb3.c
> +++ b/drivers/usb/gadget/udc/renesas_usb3.c
> @@ -2378,6 +2378,8 @@ static void handle_ext_role_switch_states(struct device *dev,
> switch (role) {
> case USB_ROLE_NONE:
> usb3->connection_state = USB_ROLE_NONE;
> + if (cur_role == USB_ROLE_HOST)
> + device_release_driver(host);
The handle_ext_role_switch_states() with role = USB_ROLE_NONE seems
to be called multiple times. So, we have to avoid multiple calling of
device_release_driver() somehow.
Best regards,
Yoshihiro Shimoda
> if (usb3->driver)
> usb3_disconnect(usb3);
> usb3_vbus_out(usb3, false);
> --
> 2.32.0
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
2022-01-31 0:23 ` Yoshihiro Shimoda
@ 2022-01-31 1:01 ` Adam Ford
2022-01-31 2:17 ` Yoshihiro Shimoda
0 siblings, 1 reply; 4+ messages in thread
From: Adam Ford @ 2022-01-31 1:01 UTC (permalink / raw)
To: Yoshihiro Shimoda
Cc: linux-usb, linux-renesas-soc, cstevens, aford, Felipe Balbi,
Greg Kroah-Hartman, Biju Das, linux-kernel
On Sun, Jan 30, 2022 at 6:23 PM Yoshihiro Shimoda
<yoshihiro.shimoda.uh@renesas.com> wrote:
>
> Hi Adam-san,
>
> Thank you for the patch!
>
> > From: Adam Ford, Sent: Saturday, January 29, 2022 7:36 AM
> >
> > The support the external role switch a variety of situations were
> > addressed, but the transition from USB_ROLE_HOST to USB_ROLE_NONE
> > leaves the host up which can cause some error messages when
> > switching from host to none, to gadget, to none, and then back
> > to host again.
>
> I think so. An external role switch in this driver is possible to
> enter the role to USB_ROLE_NONE. (Just a record for me: in other words,
> the "internal" role switch didn't enter the role to USB_ROLE_NONE.)
>
> > xhci-hcd ee000000.usb: Abort failed to stop command ring: -110
> > xhci-hcd ee000000.usb: xHCI host controller not responding, assume dead
> > xhci-hcd ee000000.usb: HC died; cleaning up
> > usb 4-1: device not accepting address 6, error -108
> > usb usb4-port1: couldn't allocate usb_device
> >
> > After this happens it will not act as a host again.
> > Fix this by releasing the host mode when transitioning to USB_ROLE_NONE.
> >
> > Fixes: 0604160d8c0b ("usb: gadget: udc: renesas_usb3: Enhance role switch support")
> > Signed-off-by: Adam Ford <aford173@gmail.com>
> >
> > diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c
> > index 57d417a7c3e0..601829a6b4ba 100644
> > --- a/drivers/usb/gadget/udc/renesas_usb3.c
> > +++ b/drivers/usb/gadget/udc/renesas_usb3.c
> > @@ -2378,6 +2378,8 @@ static void handle_ext_role_switch_states(struct device *dev,
> > switch (role) {
> > case USB_ROLE_NONE:
> > usb3->connection_state = USB_ROLE_NONE;
> > + if (cur_role == USB_ROLE_HOST)
> > + device_release_driver(host);
>
> The handle_ext_role_switch_states() with role = USB_ROLE_NONE seems
> to be called multiple times. So, we have to avoid multiple calling of
> device_release_driver() somehow.
From what I can tell, it appears that device_release_driver ultimately
calls __device_release_driver which checks for a NULL, and during the
release sets it to NULL, so subsequent releases should just get
ignored. Maybe I am missing something.
adam
>
> Best regards,
> Yoshihiro Shimoda
>
> > if (usb3->driver)
> > usb3_disconnect(usb3);
> > usb3_vbus_out(usb3, false);
> > --
> > 2.32.0
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* RE: [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
2022-01-31 1:01 ` Adam Ford
@ 2022-01-31 2:17 ` Yoshihiro Shimoda
0 siblings, 0 replies; 4+ messages in thread
From: Yoshihiro Shimoda @ 2022-01-31 2:17 UTC (permalink / raw)
To: Adam Ford
Cc: linux-usb, linux-renesas-soc, cstevens, aford, Felipe Balbi,
Greg Kroah-Hartman, Biju Das, linux-kernel
Hi Adam-san,
> From: Adam Ford, Sent: Monday, January 31, 2022 10:01 AM
>
> On Sun, Jan 30, 2022 at 6:23 PM Yoshihiro Shimoda
> <yoshihiro.shimoda.uh@renesas.com> wrote:
<snip>
> > > diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c
> > > index 57d417a7c3e0..601829a6b4ba 100644
> > > --- a/drivers/usb/gadget/udc/renesas_usb3.c
> > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c
> > > @@ -2378,6 +2378,8 @@ static void handle_ext_role_switch_states(struct device *dev,
> > > switch (role) {
> > > case USB_ROLE_NONE:
> > > usb3->connection_state = USB_ROLE_NONE;
> > > + if (cur_role == USB_ROLE_HOST)
> > > + device_release_driver(host);
> >
> > The handle_ext_role_switch_states() with role = USB_ROLE_NONE seems
> > to be called multiple times. So, we have to avoid multiple calling of
> > device_release_driver() somehow.
>
> From what I can tell, it appears that device_release_driver ultimately
> calls __device_release_driver which checks for a NULL, and during the
> release sets it to NULL, so subsequent releases should just get
> ignored. Maybe I am missing something.
Thank you for your comment. You're correct. I'm sorry, I didn't check
the __device_release_driver() behavior. This patch looks good to me. So,
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Best regards,
Yoshihiro Shimoda
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2022-01-31 2:17 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-01-28 22:36 [PATCH] usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition Adam Ford
2022-01-31 0:23 ` Yoshihiro Shimoda
2022-01-31 1:01 ` Adam Ford
2022-01-31 2:17 ` Yoshihiro Shimoda
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).