* [PATCH v6 0/2] Use the generic PHY framework for Ingenic USB PHY. @ 2020-09-23 16:25 周琰杰 (Zhou Yanjie) 2020-09-23 16:25 ` [PATCH v6 1/2] USB: PHY: JZ4770: Remove unnecessary function calls 周琰杰 (Zhou Yanjie) 2020-09-23 16:26 ` [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework 周琰杰 (Zhou Yanjie) 0 siblings, 2 replies; 5+ messages in thread From: 周琰杰 (Zhou Yanjie) @ 2020-09-23 16:25 UTC (permalink / raw) To: vkoul, kishon, gregkh, balbi, paul Cc: linux-kernel, linux-usb, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li, sernia.zhou, zhenwenjin v3->v4: Only add new generic-PHY driver, without removing the old one. Because the jz4740-musb driver is not ready to use the generic PHY framework. When the jz4740-musb driver is modified to use the generic PHY framework, the old jz4770-phy driver can be "retired". v4->v5: 1.Add an extra blank line between "devm_of_phy_provider_register" and "return". 2.Remove unnecessary "phy_set_drvdata". 3.Add Paul Cercueil's Reviewed-by. v5->v6: 1.Revert the removal of "phy_set_drvdata" in v5, removing "phy_set_drvdata" will cause a kernel panic on CI20. Reported-by: H. Nikolaus Schaller <hns@goldelico.com> 2.Rewrite the macro definitions, replace the original code with "FIELD_PREP()" and "u32p_replace_bits()" according to Vinod Koul's suggestion. 周琰杰 (Zhou Yanjie) (2): USB: PHY: JZ4770: Remove unnecessary function calls. PHY: Ingenic: Add USB PHY driver using generic PHY framework. drivers/phy/Kconfig | 1 + drivers/phy/Makefile | 1 + drivers/phy/ingenic/Kconfig | 12 ++ drivers/phy/ingenic/Makefile | 2 + drivers/phy/ingenic/phy-ingenic-usb.c | 378 ++++++++++++++++++++++++++++++++++ drivers/usb/phy/phy-jz4770.c | 2 +- 6 files changed, 395 insertions(+), 1 deletion(-) create mode 100644 drivers/phy/ingenic/Kconfig create mode 100644 drivers/phy/ingenic/Makefile create mode 100644 drivers/phy/ingenic/phy-ingenic-usb.c -- 2.11.0 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v6 1/2] USB: PHY: JZ4770: Remove unnecessary function calls. 2020-09-23 16:25 [PATCH v6 0/2] Use the generic PHY framework for Ingenic USB PHY 周琰杰 (Zhou Yanjie) @ 2020-09-23 16:25 ` 周琰杰 (Zhou Yanjie) 2020-09-23 16:26 ` [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework 周琰杰 (Zhou Yanjie) 1 sibling, 0 replies; 5+ messages in thread From: 周琰杰 (Zhou Yanjie) @ 2020-09-23 16:25 UTC (permalink / raw) To: vkoul, kishon, gregkh, balbi, paul Cc: linux-kernel, linux-usb, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li, sernia.zhou, zhenwenjin Remove unnecessary "of_match_ptr()", because Ingenic SoCs all depend on Device Tree. Suggested-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> --- Notes: v3: New patch. v3->v4: No change. v4->v5: Add Paul Cercueil's Reviewed-by. v5->v6: No change. drivers/usb/phy/phy-jz4770.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/phy/phy-jz4770.c b/drivers/usb/phy/phy-jz4770.c index f6d3731581eb..4025da20b3fd 100644 --- a/drivers/usb/phy/phy-jz4770.c +++ b/drivers/usb/phy/phy-jz4770.c @@ -350,7 +350,7 @@ static struct platform_driver ingenic_phy_driver = { .probe = jz4770_phy_probe, .driver = { .name = "jz4770-phy", - .of_match_table = of_match_ptr(ingenic_usb_phy_of_matches), + .of_match_table = ingenic_usb_phy_of_matches, }, }; module_platform_driver(ingenic_phy_driver); -- 2.11.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework. 2020-09-23 16:25 [PATCH v6 0/2] Use the generic PHY framework for Ingenic USB PHY 周琰杰 (Zhou Yanjie) 2020-09-23 16:25 ` [PATCH v6 1/2] USB: PHY: JZ4770: Remove unnecessary function calls 周琰杰 (Zhou Yanjie) @ 2020-09-23 16:26 ` 周琰杰 (Zhou Yanjie) 2020-09-23 17:29 ` Paul Cercueil 1 sibling, 1 reply; 5+ messages in thread From: 周琰杰 (Zhou Yanjie) @ 2020-09-23 16:26 UTC (permalink / raw) To: vkoul, kishon, gregkh, balbi, paul Cc: linux-kernel, linux-usb, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li, sernia.zhou, zhenwenjin Used the generic PHY framework API to create the PHY, this driver supoorts USB OTG PHY used in JZ4770 SoC, JZ4780 SoC, X1000 SoC, and X1830 SoC. Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> --- Notes: v1->v2: Fix bug, ".of_match_table = of_match_ptr(ingenic_usb_phy_of_matches)" is wrong and should be replaced with ".of_match_table = ingenic_usb_phy_of_matches". v2->v3: 1.Change "depends on (MACH_INGENIC && MIPS) || COMPILE_TEST" to "depends on MIPS || COMPILE_TEST". 2.Keep the adjustments of "ingenic_usb_phy_init()" and "ingenic_usb_phu_exit()" positions in v2 to make them consistent with the order in "ingenic_usb_phy_ops", keep the adjustments to the positions of "ingenic_usb_phy_of_matches[]" in v2 to keep them consistent with the styles of other USB PHY drivers. And remove some unnecessary changes to reduce the diff size, from the original 256 lines change to the current 209 lines. v3->v4: Only add new generic-PHY driver, without removing the old one. Because the jz4740-musb driver is not ready to use the generic PHY framework. When the jz4740-musb driver is modified to use the generic PHY framework, the old jz4770-phy driver can be "retired". v4->v5: 1.Add an extra blank line between "devm_of_phy_provider_register" and "return". 2.Remove unnecessary "phy_set_drvdata". 3.Add Paul Cercueil's Reviewed-by. v5->v6: 1.Revert the removal of "phy_set_drvdata" in v5, removing "phy_set_drvdata" will cause a kernel panic on CI20. Reported-by: H. Nikolaus Schaller <hns@goldelico.com> 2.Rewrite the macro definitions, replace the original code with "FIELD_PREP()" and "u32p_replace_bits()" according to Vinod Koul's suggestion. drivers/phy/Kconfig | 1 + drivers/phy/Makefile | 1 + drivers/phy/ingenic/Kconfig | 12 ++ drivers/phy/ingenic/Makefile | 2 + drivers/phy/ingenic/phy-ingenic-usb.c | 378 ++++++++++++++++++++++++++++++++++ 5 files changed, 394 insertions(+) create mode 100644 drivers/phy/ingenic/Kconfig create mode 100644 drivers/phy/ingenic/Makefile create mode 100644 drivers/phy/ingenic/phy-ingenic-usb.c diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index de9362c25c07..0534b0fdd057 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -55,6 +55,7 @@ source "drivers/phy/broadcom/Kconfig" source "drivers/phy/cadence/Kconfig" source "drivers/phy/freescale/Kconfig" source "drivers/phy/hisilicon/Kconfig" +source "drivers/phy/ingenic/Kconfig" source "drivers/phy/lantiq/Kconfig" source "drivers/phy/marvell/Kconfig" source "drivers/phy/mediatek/Kconfig" diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index c27408e4daae..ab24f0d20763 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -14,6 +14,7 @@ obj-y += allwinner/ \ cadence/ \ freescale/ \ hisilicon/ \ + ingenic/ \ intel/ \ lantiq/ \ marvell/ \ diff --git a/drivers/phy/ingenic/Kconfig b/drivers/phy/ingenic/Kconfig new file mode 100644 index 000000000000..912b14e512cb --- /dev/null +++ b/drivers/phy/ingenic/Kconfig @@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Phy drivers for Ingenic platforms +# +config PHY_INGENIC_USB + tristate "Ingenic SoCs USB PHY Driver" + depends on MIPS || COMPILE_TEST + depends on USB_SUPPORT + select GENERIC_PHY + help + This driver provides USB PHY support for the USB controller found + on the JZ-series and X-series SoCs from Ingenic. diff --git a/drivers/phy/ingenic/Makefile b/drivers/phy/ingenic/Makefile new file mode 100644 index 000000000000..65d5ea00fc9d --- /dev/null +++ b/drivers/phy/ingenic/Makefile @@ -0,0 +1,2 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-y += phy-ingenic-usb.o diff --git a/drivers/phy/ingenic/phy-ingenic-usb.c b/drivers/phy/ingenic/phy-ingenic-usb.c new file mode 100644 index 000000000000..55da6ca8faf7 --- /dev/null +++ b/drivers/phy/ingenic/phy-ingenic-usb.c @@ -0,0 +1,378 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Ingenic SoCs USB PHY driver + * Copyright (c) Paul Cercueil <paul@crapouillou.net> + * Copyright (c) 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> + * Copyright (c) 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> + */ + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/regulator/consumer.h> + +/* OTGPHY register offsets */ +#define REG_USBPCR_OFFSET 0x00 +#define REG_USBRDT_OFFSET 0x04 +#define REG_USBVBFIL_OFFSET 0x08 +#define REG_USBPCR1_OFFSET 0x0c + +/* bits within the USBPCR register */ +#define USBPCR_USB_MODE BIT(31) +#define USBPCR_AVLD_REG BIT(30) +#define USBPCR_COMMONONN BIT(25) +#define USBPCR_VBUSVLDEXT BIT(24) +#define USBPCR_VBUSVLDEXTSEL BIT(23) +#define USBPCR_POR BIT(22) +#define USBPCR_SIDDQ BIT(21) +#define USBPCR_OTG_DISABLE BIT(20) +#define USBPCR_TXPREEMPHTUNE BIT(6) + +#define USBPCR_IDPULLUP_MASK GENMASK(29, 28) +#define USBPCR_IDPULLUP_ALWAYS 0x2 +#define USBPCR_IDPULLUP_SUSPEND 0x1 +#define USBPCR_IDPULLUP_OTG 0x0 + +#define USBPCR_COMPDISTUNE_MASK GENMASK(19, 17) +#define USBPCR_COMPDISTUNE_DFT 0x4 + +#define USBPCR_OTGTUNE_MASK GENMASK(16, 14) +#define USBPCR_OTGTUNE_DFT 0x4 + +#define USBPCR_SQRXTUNE_MASK GENMASK(13, 11) +#define USBPCR_SQRXTUNE_DCR_20PCT 0x7 +#define USBPCR_SQRXTUNE_DFT 0x3 + +#define USBPCR_TXFSLSTUNE_MASK GENMASK(10, 7) +#define USBPCR_TXFSLSTUNE_DCR_50PPT 0xf +#define USBPCR_TXFSLSTUNE_DCR_25PPT 0x7 +#define USBPCR_TXFSLSTUNE_DFT 0x3 +#define USBPCR_TXFSLSTUNE_INC_25PPT 0x1 +#define USBPCR_TXFSLSTUNE_INC_50PPT 0x0 + +#define USBPCR_TXHSXVTUNE_MASK GENMASK(5, 4) +#define USBPCR_TXHSXVTUNE_DFT 0x3 +#define USBPCR_TXHSXVTUNE_DCR_15MV 0x1 + +#define USBPCR_TXRISETUNE_MASK GENMASK(5, 4) +#define USBPCR_TXRISETUNE_DFT 0x3 + +#define USBPCR_TXVREFTUNE_MASK GENMASK(3, 0) +#define USBPCR_TXVREFTUNE_INC_25PPT 0x7 +#define USBPCR_TXVREFTUNE_DFT 0x5 + +/* bits within the USBRDTR register */ +#define USBRDT_UTMI_RST BIT(27) +#define USBRDT_HB_MASK BIT(26) +#define USBRDT_VBFIL_LD_EN BIT(25) +#define USBRDT_IDDIG_EN BIT(24) +#define USBRDT_IDDIG_REG BIT(23) +#define USBRDT_VBFIL_EN BIT(2) + +/* bits within the USBPCR1 register */ +#define USBPCR1_BVLD_REG BIT(31) +#define USBPCR1_DPPD BIT(29) +#define USBPCR1_DMPD BIT(28) +#define USBPCR1_USB_SEL BIT(28) +#define USBPCR1_WORD_IF_16BIT BIT(19) + +enum ingenic_usb_phy_version { + ID_JZ4770, + ID_JZ4780, + ID_X1000, + ID_X1830, +}; + +struct ingenic_soc_info { + enum ingenic_usb_phy_version version; + + void (*usb_phy_init)(struct phy *phy); +}; + +struct ingenic_usb_phy { + const struct ingenic_soc_info *soc_info; + + struct phy *phy; + struct device *dev; + void __iomem *base; + struct clk *clk; + struct regulator *vcc_supply; +}; + +static int ingenic_usb_phy_init(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + int err; + u32 reg; + + err = clk_prepare_enable(priv->clk); + if (err) { + dev_err(priv->dev, "Unable to start clock: %d\n", err); + return err; + } + + priv->soc_info->usb_phy_init(phy); + + /* Wait for PHY to reset */ + usleep_range(30, 300); + reg = readl(priv->base + REG_USBPCR_OFFSET); + writel(reg & ~USBPCR_POR, priv->base + REG_USBPCR_OFFSET); + usleep_range(300, 1000); + + return 0; +} + +static int ingenic_usb_phy_exit(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + + clk_disable_unprepare(priv->clk); + regulator_disable(priv->vcc_supply); + + return 0; +} + +static int ingenic_usb_phy_power_on(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + int err; + + err = regulator_enable(priv->vcc_supply); + if (err) { + dev_err(priv->dev, "Unable to enable VCC: %d\n", err); + return err; + } + + return 0; +} + +static int ingenic_usb_phy_power_off(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + + regulator_disable(priv->vcc_supply); + + return 0; +} + +static int ingenic_usb_phy_set_mode(struct phy *phy, + enum phy_mode mode, int submode) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + u32 reg; + + switch (mode) { + case PHY_MODE_USB_HOST: + reg = readl(priv->base + REG_USBPCR_OFFSET); + u32p_replace_bits(®, 1, USBPCR_USB_MODE); + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXT); + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXTSEL); + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); + writel(reg, priv->base + REG_USBPCR_OFFSET); + + break; + case PHY_MODE_USB_DEVICE: + if (priv->soc_info->version >= ID_X1000) { + reg = readl(priv->base + REG_USBPCR1_OFFSET); + u32p_replace_bits(®, 1, USBPCR1_BVLD_REG); + writel(reg, priv->base + REG_USBPCR1_OFFSET); + } + + reg = readl(priv->base + REG_USBPCR_OFFSET); + u32p_replace_bits(®, 0, USBPCR_USB_MODE); + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); + u32p_replace_bits(®, 1, USBPCR_OTG_DISABLE); + writel(reg, priv->base + REG_USBPCR_OFFSET); + + break; + case PHY_MODE_USB_OTG: + reg = readl(priv->base + REG_USBPCR_OFFSET); + u32p_replace_bits(®, 1, USBPCR_USB_MODE); + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); + writel(reg, priv->base + REG_USBPCR_OFFSET); + + break; + default: + return -EINVAL; + } + + return 0; +} + +static const struct phy_ops ingenic_usb_phy_ops = { + .init = ingenic_usb_phy_init, + .exit = ingenic_usb_phy_exit, + .power_on = ingenic_usb_phy_power_on, + .power_off = ingenic_usb_phy_power_off, + .set_mode = ingenic_usb_phy_set_mode, + .owner = THIS_MODULE, +}; + +static void jz4770_usb_phy_init(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + u32 reg; + + reg = USBPCR_AVLD_REG | USBPCR_COMMONONN | USBPCR_POR | + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_ALWAYS) | + FIELD_PREP(USBPCR_COMPDISTUNE_MASK, USBPCR_COMPDISTUNE_DFT) | + FIELD_PREP(USBPCR_OTGTUNE_MASK, USBPCR_OTGTUNE_DFT) | + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DFT) | + FIELD_PREP(USBPCR_TXFSLSTUNE_MASK, USBPCR_TXFSLSTUNE_DFT) | + FIELD_PREP(USBPCR_TXRISETUNE_MASK, USBPCR_TXRISETUNE_DFT) | + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, USBPCR_TXVREFTUNE_DFT); + writel(reg, priv->base + REG_USBPCR_OFFSET); +} + +static void jz4780_usb_phy_init(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + u32 reg; + + reg = readl(priv->base + REG_USBPCR1_OFFSET) | USBPCR1_USB_SEL | + USBPCR1_WORD_IF_16BIT; + writel(reg, priv->base + REG_USBPCR1_OFFSET); + + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR; + writel(reg, priv->base + REG_USBPCR_OFFSET); +} + +static void x1000_usb_phy_init(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + u32 reg; + + reg = readl(priv->base + REG_USBPCR1_OFFSET) | USBPCR1_WORD_IF_16BIT; + writel(reg, priv->base + REG_USBPCR1_OFFSET); + + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR | + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DCR_20PCT) | + FIELD_PREP(USBPCR_TXHSXVTUNE_MASK, USBPCR_TXHSXVTUNE_DCR_15MV) | + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, USBPCR_TXVREFTUNE_INC_25PPT); + writel(reg, priv->base + REG_USBPCR_OFFSET); +} + +static void x1830_usb_phy_init(struct phy *phy) +{ + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); + u32 reg; + + /* rdt */ + writel(USBRDT_VBFIL_EN | USBRDT_UTMI_RST, priv->base + REG_USBRDT_OFFSET); + + reg = readl(priv->base + REG_USBPCR1_OFFSET) | USBPCR1_WORD_IF_16BIT | + USBPCR1_DMPD | USBPCR1_DPPD; + writel(reg, priv->base + REG_USBPCR1_OFFSET); + + reg = USBPCR_VBUSVLDEXT | USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR | + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_OTG); + writel(reg, priv->base + REG_USBPCR_OFFSET); +} + +static const struct ingenic_soc_info jz4770_soc_info = { + .version = ID_JZ4770, + + .usb_phy_init = jz4770_usb_phy_init, +}; + +static const struct ingenic_soc_info jz4780_soc_info = { + .version = ID_JZ4780, + + .usb_phy_init = jz4780_usb_phy_init, +}; + +static const struct ingenic_soc_info x1000_soc_info = { + .version = ID_X1000, + + .usb_phy_init = x1000_usb_phy_init, +}; + +static const struct ingenic_soc_info x1830_soc_info = { + .version = ID_X1830, + + .usb_phy_init = x1830_usb_phy_init, +}; + +static int ingenic_usb_phy_probe(struct platform_device *pdev) +{ + struct ingenic_usb_phy *priv; + struct phy_provider *provider; + struct device *dev = &pdev->dev; + int err; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->soc_info = device_get_match_data(dev); + if (!priv->soc_info) { + dev_err(dev, "Error: No device match found\n"); + return -ENODEV; + } + + platform_set_drvdata(pdev, priv); + priv->dev = dev; + + priv->base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(priv->base)) { + dev_err(dev, "Failed to map registers\n"); + return PTR_ERR(priv->base); + } + + priv->clk = devm_clk_get(dev, NULL); + if (IS_ERR(priv->clk)) { + err = PTR_ERR(priv->clk); + if (err != -EPROBE_DEFER) + dev_err(dev, "Failed to get clock\n"); + return err; + } + + priv->vcc_supply = devm_regulator_get(dev, "vcc"); + if (IS_ERR(priv->vcc_supply)) { + err = PTR_ERR(priv->vcc_supply); + if (err != -EPROBE_DEFER) + dev_err(dev, "Failed to get regulator\n"); + return err; + } + + priv->phy = devm_phy_create(dev, NULL, &ingenic_usb_phy_ops); + if (IS_ERR(priv)) + return PTR_ERR(priv); + + phy_set_drvdata(priv->phy, priv); + + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + + return PTR_ERR_OR_ZERO(provider); +} + +static const struct of_device_id ingenic_usb_phy_of_matches[] = { + { .compatible = "ingenic,jz4770-phy", .data = &jz4770_soc_info }, + { .compatible = "ingenic,jz4780-phy", .data = &jz4780_soc_info }, + { .compatible = "ingenic,x1000-phy", .data = &x1000_soc_info }, + { .compatible = "ingenic,x1830-phy", .data = &x1830_soc_info }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, ingenic_usb_phy_of_matches); + +static struct platform_driver ingenic_usb_phy_driver = { + .probe = ingenic_usb_phy_probe, + .driver = { + .name = "ingenic-usb-phy", + .of_match_table = ingenic_usb_phy_of_matches, + }, +}; +module_platform_driver(ingenic_usb_phy_driver); + +MODULE_AUTHOR("周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>"); +MODULE_AUTHOR("漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>"); +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>"); +MODULE_DESCRIPTION("Ingenic SoCs USB PHY driver"); +MODULE_LICENSE("GPL"); -- 2.11.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework. 2020-09-23 16:26 ` [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework 周琰杰 (Zhou Yanjie) @ 2020-09-23 17:29 ` Paul Cercueil 2020-09-25 15:10 ` Zhou Yanjie 0 siblings, 1 reply; 5+ messages in thread From: Paul Cercueil @ 2020-09-23 17:29 UTC (permalink / raw) To: 周琰杰 Cc: vkoul, kishon, gregkh, balbi, linux-kernel, linux-usb, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li, sernia.zhou, zhenwenjin Hi Zhou, Le jeu. 24 sept. 2020 à 0:26, 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> a écrit : > Used the generic PHY framework API to create the PHY, this driver > supoorts USB OTG PHY used in JZ4770 SoC, JZ4780 SoC, X1000 SoC, > and X1830 SoC. > > Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> > Tested-by: H. Nikolaus Schaller <hns@goldelico.com> > Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> > Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> > Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> > Reviewed-by: Paul Cercueil <paul@crapouillou.net> > --- > > Notes: > v1->v2: > Fix bug, ".of_match_table = > of_match_ptr(ingenic_usb_phy_of_matches)" is wrong > and should be replaced with ".of_match_table = > ingenic_usb_phy_of_matches". > > v2->v3: > 1.Change "depends on (MACH_INGENIC && MIPS) || COMPILE_TEST" to > "depends on MIPS || COMPILE_TEST". > 2.Keep the adjustments of "ingenic_usb_phy_init()" and > "ingenic_usb_phu_exit()" > positions in v2 to make them consistent with the order in > "ingenic_usb_phy_ops", > keep the adjustments to the positions of > "ingenic_usb_phy_of_matches[]" in v2 > to keep them consistent with the styles of other USB PHY > drivers. And remove > some unnecessary changes to reduce the diff size, from the > original 256 lines > change to the current 209 lines. > > v3->v4: > Only add new generic-PHY driver, without removing the old one. > Because the > jz4740-musb driver is not ready to use the generic PHY framework. > When the > jz4740-musb driver is modified to use the generic PHY framework, > the old > jz4770-phy driver can be "retired". > > v4->v5: > 1.Add an extra blank line between "devm_of_phy_provider_register" > and "return". > 2.Remove unnecessary "phy_set_drvdata". > 3.Add Paul Cercueil's Reviewed-by. > > v5->v6: > 1.Revert the removal of "phy_set_drvdata" in v5, removing > "phy_set_drvdata" will > cause a kernel panic on CI20. > Reported-by: H. Nikolaus Schaller <hns@goldelico.com> My bad, I overlooked the code of phy_set_drvdata(), indeed phy->dev and pdev->dev are different. Sorry about that. With that said, you should then be able to remove the platform_set_drvdata() call. > 2.Rewrite the macro definitions, replace the original code with > "FIELD_PREP()" > and "u32p_replace_bits()" according to Vinod Koul's suggestion. > > drivers/phy/Kconfig | 1 + > drivers/phy/Makefile | 1 + > drivers/phy/ingenic/Kconfig | 12 ++ > drivers/phy/ingenic/Makefile | 2 + > drivers/phy/ingenic/phy-ingenic-usb.c | 378 > ++++++++++++++++++++++++++++++++++ > 5 files changed, 394 insertions(+) > create mode 100644 drivers/phy/ingenic/Kconfig > create mode 100644 drivers/phy/ingenic/Makefile > create mode 100644 drivers/phy/ingenic/phy-ingenic-usb.c > > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > index de9362c25c07..0534b0fdd057 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -55,6 +55,7 @@ source "drivers/phy/broadcom/Kconfig" > source "drivers/phy/cadence/Kconfig" > source "drivers/phy/freescale/Kconfig" > source "drivers/phy/hisilicon/Kconfig" > +source "drivers/phy/ingenic/Kconfig" > source "drivers/phy/lantiq/Kconfig" > source "drivers/phy/marvell/Kconfig" > source "drivers/phy/mediatek/Kconfig" > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index c27408e4daae..ab24f0d20763 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -14,6 +14,7 @@ obj-y += allwinner/ \ > cadence/ \ > freescale/ \ > hisilicon/ \ > + ingenic/ \ > intel/ \ > lantiq/ \ > marvell/ \ > diff --git a/drivers/phy/ingenic/Kconfig b/drivers/phy/ingenic/Kconfig > new file mode 100644 > index 000000000000..912b14e512cb > --- /dev/null > +++ b/drivers/phy/ingenic/Kconfig > @@ -0,0 +1,12 @@ > +# SPDX-License-Identifier: GPL-2.0 > +# > +# Phy drivers for Ingenic platforms > +# > +config PHY_INGENIC_USB > + tristate "Ingenic SoCs USB PHY Driver" > + depends on MIPS || COMPILE_TEST > + depends on USB_SUPPORT > + select GENERIC_PHY > + help > + This driver provides USB PHY support for the USB controller found > + on the JZ-series and X-series SoCs from Ingenic. > diff --git a/drivers/phy/ingenic/Makefile > b/drivers/phy/ingenic/Makefile > new file mode 100644 > index 000000000000..65d5ea00fc9d > --- /dev/null > +++ b/drivers/phy/ingenic/Makefile > @@ -0,0 +1,2 @@ > +# SPDX-License-Identifier: GPL-2.0 > +obj-y += phy-ingenic-usb.o > diff --git a/drivers/phy/ingenic/phy-ingenic-usb.c > b/drivers/phy/ingenic/phy-ingenic-usb.c > new file mode 100644 > index 000000000000..55da6ca8faf7 > --- /dev/null > +++ b/drivers/phy/ingenic/phy-ingenic-usb.c > @@ -0,0 +1,378 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Ingenic SoCs USB PHY driver > + * Copyright (c) Paul Cercueil <paul@crapouillou.net> > + * Copyright (c) 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> > + * Copyright (c) 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> > + */ > + > +#include <linux/bitfield.h> > +#include <linux/clk.h> > +#include <linux/delay.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/regulator/consumer.h> > + > +/* OTGPHY register offsets */ > +#define REG_USBPCR_OFFSET 0x00 > +#define REG_USBRDT_OFFSET 0x04 > +#define REG_USBVBFIL_OFFSET 0x08 > +#define REG_USBPCR1_OFFSET 0x0c > + > +/* bits within the USBPCR register */ > +#define USBPCR_USB_MODE BIT(31) > +#define USBPCR_AVLD_REG BIT(30) > +#define USBPCR_COMMONONN BIT(25) > +#define USBPCR_VBUSVLDEXT BIT(24) > +#define USBPCR_VBUSVLDEXTSEL BIT(23) > +#define USBPCR_POR BIT(22) > +#define USBPCR_SIDDQ BIT(21) > +#define USBPCR_OTG_DISABLE BIT(20) > +#define USBPCR_TXPREEMPHTUNE BIT(6) > + > +#define USBPCR_IDPULLUP_MASK GENMASK(29, 28) > +#define USBPCR_IDPULLUP_ALWAYS 0x2 > +#define USBPCR_IDPULLUP_SUSPEND 0x1 > +#define USBPCR_IDPULLUP_OTG 0x0 > + > +#define USBPCR_COMPDISTUNE_MASK GENMASK(19, 17) > +#define USBPCR_COMPDISTUNE_DFT 0x4 > + > +#define USBPCR_OTGTUNE_MASK GENMASK(16, 14) > +#define USBPCR_OTGTUNE_DFT 0x4 > + > +#define USBPCR_SQRXTUNE_MASK GENMASK(13, 11) > +#define USBPCR_SQRXTUNE_DCR_20PCT 0x7 > +#define USBPCR_SQRXTUNE_DFT 0x3 > + > +#define USBPCR_TXFSLSTUNE_MASK GENMASK(10, 7) > +#define USBPCR_TXFSLSTUNE_DCR_50PPT 0xf > +#define USBPCR_TXFSLSTUNE_DCR_25PPT 0x7 > +#define USBPCR_TXFSLSTUNE_DFT 0x3 > +#define USBPCR_TXFSLSTUNE_INC_25PPT 0x1 > +#define USBPCR_TXFSLSTUNE_INC_50PPT 0x0 > + > +#define USBPCR_TXHSXVTUNE_MASK GENMASK(5, 4) > +#define USBPCR_TXHSXVTUNE_DFT 0x3 > +#define USBPCR_TXHSXVTUNE_DCR_15MV 0x1 > + > +#define USBPCR_TXRISETUNE_MASK GENMASK(5, 4) > +#define USBPCR_TXRISETUNE_DFT 0x3 > + > +#define USBPCR_TXVREFTUNE_MASK GENMASK(3, 0) > +#define USBPCR_TXVREFTUNE_INC_25PPT 0x7 > +#define USBPCR_TXVREFTUNE_DFT 0x5 > + > +/* bits within the USBRDTR register */ > +#define USBRDT_UTMI_RST BIT(27) > +#define USBRDT_HB_MASK BIT(26) > +#define USBRDT_VBFIL_LD_EN BIT(25) > +#define USBRDT_IDDIG_EN BIT(24) > +#define USBRDT_IDDIG_REG BIT(23) > +#define USBRDT_VBFIL_EN BIT(2) > + > +/* bits within the USBPCR1 register */ > +#define USBPCR1_BVLD_REG BIT(31) > +#define USBPCR1_DPPD BIT(29) > +#define USBPCR1_DMPD BIT(28) > +#define USBPCR1_USB_SEL BIT(28) > +#define USBPCR1_WORD_IF_16BIT BIT(19) > + > +enum ingenic_usb_phy_version { > + ID_JZ4770, > + ID_JZ4780, > + ID_X1000, > + ID_X1830, > +}; > + > +struct ingenic_soc_info { > + enum ingenic_usb_phy_version version; > + > + void (*usb_phy_init)(struct phy *phy); > +}; > + > +struct ingenic_usb_phy { > + const struct ingenic_soc_info *soc_info; > + > + struct phy *phy; > + struct device *dev; > + void __iomem *base; > + struct clk *clk; > + struct regulator *vcc_supply; > +}; > + > +static int ingenic_usb_phy_init(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + int err; > + u32 reg; > + > + err = clk_prepare_enable(priv->clk); > + if (err) { > + dev_err(priv->dev, "Unable to start clock: %d\n", err); > + return err; > + } > + > + priv->soc_info->usb_phy_init(phy); > + > + /* Wait for PHY to reset */ > + usleep_range(30, 300); > + reg = readl(priv->base + REG_USBPCR_OFFSET); > + writel(reg & ~USBPCR_POR, priv->base + REG_USBPCR_OFFSET); > + usleep_range(300, 1000); > + > + return 0; > +} > + > +static int ingenic_usb_phy_exit(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + > + clk_disable_unprepare(priv->clk); > + regulator_disable(priv->vcc_supply); > + > + return 0; > +} > + > +static int ingenic_usb_phy_power_on(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + int err; > + > + err = regulator_enable(priv->vcc_supply); > + if (err) { > + dev_err(priv->dev, "Unable to enable VCC: %d\n", err); > + return err; > + } > + > + return 0; > +} > + > +static int ingenic_usb_phy_power_off(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + > + regulator_disable(priv->vcc_supply); > + > + return 0; > +} > + > +static int ingenic_usb_phy_set_mode(struct phy *phy, > + enum phy_mode mode, int submode) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + u32 reg; > + > + switch (mode) { > + case PHY_MODE_USB_HOST: > + reg = readl(priv->base + REG_USBPCR_OFFSET); > + u32p_replace_bits(®, 1, USBPCR_USB_MODE); > + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXT); > + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXTSEL); > + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > + > + break; > + case PHY_MODE_USB_DEVICE: > + if (priv->soc_info->version >= ID_X1000) { > + reg = readl(priv->base + REG_USBPCR1_OFFSET); > + u32p_replace_bits(®, 1, USBPCR1_BVLD_REG); > + writel(reg, priv->base + REG_USBPCR1_OFFSET); > + } > + > + reg = readl(priv->base + REG_USBPCR_OFFSET); > + u32p_replace_bits(®, 0, USBPCR_USB_MODE); > + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); > + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); > + u32p_replace_bits(®, 1, USBPCR_OTG_DISABLE); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > + > + break; > + case PHY_MODE_USB_OTG: > + reg = readl(priv->base + REG_USBPCR_OFFSET); > + u32p_replace_bits(®, 1, USBPCR_USB_MODE); > + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); > + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); > + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > + > + break; > + default: > + return -EINVAL; > + } > + > + return 0; > +} > + > +static const struct phy_ops ingenic_usb_phy_ops = { > + .init = ingenic_usb_phy_init, > + .exit = ingenic_usb_phy_exit, > + .power_on = ingenic_usb_phy_power_on, > + .power_off = ingenic_usb_phy_power_off, > + .set_mode = ingenic_usb_phy_set_mode, > + .owner = THIS_MODULE, > +}; > + > +static void jz4770_usb_phy_init(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + u32 reg; > + > + reg = USBPCR_AVLD_REG | USBPCR_COMMONONN | USBPCR_POR | > + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_ALWAYS) | > + FIELD_PREP(USBPCR_COMPDISTUNE_MASK, USBPCR_COMPDISTUNE_DFT) | > + FIELD_PREP(USBPCR_OTGTUNE_MASK, USBPCR_OTGTUNE_DFT) | > + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DFT) | > + FIELD_PREP(USBPCR_TXFSLSTUNE_MASK, USBPCR_TXFSLSTUNE_DFT) | > + FIELD_PREP(USBPCR_TXRISETUNE_MASK, USBPCR_TXRISETUNE_DFT) | > + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, USBPCR_TXVREFTUNE_DFT); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > +} > + > +static void jz4780_usb_phy_init(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + u32 reg; > + > + reg = readl(priv->base + REG_USBPCR1_OFFSET) | USBPCR1_USB_SEL | > + USBPCR1_WORD_IF_16BIT; > + writel(reg, priv->base + REG_USBPCR1_OFFSET); > + > + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR; > + writel(reg, priv->base + REG_USBPCR_OFFSET); > +} > + > +static void x1000_usb_phy_init(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + u32 reg; > + > + reg = readl(priv->base + REG_USBPCR1_OFFSET) | > USBPCR1_WORD_IF_16BIT; > + writel(reg, priv->base + REG_USBPCR1_OFFSET); > + > + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR | > + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DCR_20PCT) | > + FIELD_PREP(USBPCR_TXHSXVTUNE_MASK, USBPCR_TXHSXVTUNE_DCR_15MV) | > + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, USBPCR_TXVREFTUNE_INC_25PPT); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > +} > + > +static void x1830_usb_phy_init(struct phy *phy) > +{ > + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); > + u32 reg; > + > + /* rdt */ > + writel(USBRDT_VBFIL_EN | USBRDT_UTMI_RST, priv->base + > REG_USBRDT_OFFSET); > + > + reg = readl(priv->base + REG_USBPCR1_OFFSET) | > USBPCR1_WORD_IF_16BIT | > + USBPCR1_DMPD | USBPCR1_DPPD; > + writel(reg, priv->base + REG_USBPCR1_OFFSET); > + > + reg = USBPCR_VBUSVLDEXT | USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | > USBPCR_POR | There's a stray tab character here. > + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_OTG); > + writel(reg, priv->base + REG_USBPCR_OFFSET); > +} > + > +static const struct ingenic_soc_info jz4770_soc_info = { > + .version = ID_JZ4770, > + > + .usb_phy_init = jz4770_usb_phy_init, > +}; > + > +static const struct ingenic_soc_info jz4780_soc_info = { > + .version = ID_JZ4780, > + > + .usb_phy_init = jz4780_usb_phy_init, > +}; > + > +static const struct ingenic_soc_info x1000_soc_info = { > + .version = ID_X1000, > + > + .usb_phy_init = x1000_usb_phy_init, > +}; > + > +static const struct ingenic_soc_info x1830_soc_info = { > + .version = ID_X1830, > + > + .usb_phy_init = x1830_usb_phy_init, > +}; > + > +static int ingenic_usb_phy_probe(struct platform_device *pdev) > +{ > + struct ingenic_usb_phy *priv; > + struct phy_provider *provider; > + struct device *dev = &pdev->dev; > + int err; > + > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + > + priv->soc_info = device_get_match_data(dev); > + if (!priv->soc_info) { > + dev_err(dev, "Error: No device match found\n"); > + return -ENODEV; > + } > + > + platform_set_drvdata(pdev, priv); You should be able to remove the platform_set_drvdata() here. Not the phy_set_drvdata() ;) > + priv->dev = dev; You may also remove the "dev" field in your priv structure, and use &phy->dev instead, from what I can see it's only used in your dev_err() calls. Not a deal-breaker though, I'm fine with both. > + > + priv->base = devm_platform_ioremap_resource(pdev, 0); > + if (IS_ERR(priv->base)) { > + dev_err(dev, "Failed to map registers\n"); > + return PTR_ERR(priv->base); > + } > + > + priv->clk = devm_clk_get(dev, NULL); > + if (IS_ERR(priv->clk)) { > + err = PTR_ERR(priv->clk); > + if (err != -EPROBE_DEFER) > + dev_err(dev, "Failed to get clock\n"); > + return err; You can do: if (IS_ERR(priv->clk)) return dev_err_probe(dev, PTR_ERR(priv->clk), "Failed to get clock\n"); if Vinod is okay with that (I know some maintainers don't like it). > + } > + > + priv->vcc_supply = devm_regulator_get(dev, "vcc"); > + if (IS_ERR(priv->vcc_supply)) { > + err = PTR_ERR(priv->vcc_supply); > + if (err != -EPROBE_DEFER) > + dev_err(dev, "Failed to get regulator\n"); > + return err; Same here. These are nitpicks though and I'm happy with the V6 being merged. Cheers, -Paul > + } > + > + priv->phy = devm_phy_create(dev, NULL, &ingenic_usb_phy_ops); > + if (IS_ERR(priv)) > + return PTR_ERR(priv); > + > + phy_set_drvdata(priv->phy, priv); > + > + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); > + > + return PTR_ERR_OR_ZERO(provider); > +} > + > +static const struct of_device_id ingenic_usb_phy_of_matches[] = { > + { .compatible = "ingenic,jz4770-phy", .data = &jz4770_soc_info }, > + { .compatible = "ingenic,jz4780-phy", .data = &jz4780_soc_info }, > + { .compatible = "ingenic,x1000-phy", .data = &x1000_soc_info }, > + { .compatible = "ingenic,x1830-phy", .data = &x1830_soc_info }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, ingenic_usb_phy_of_matches); > + > +static struct platform_driver ingenic_usb_phy_driver = { > + .probe = ingenic_usb_phy_probe, > + .driver = { > + .name = "ingenic-usb-phy", > + .of_match_table = ingenic_usb_phy_of_matches, > + }, > +}; > +module_platform_driver(ingenic_usb_phy_driver); > + > +MODULE_AUTHOR("周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>"); > +MODULE_AUTHOR("漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>"); > +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>"); > +MODULE_DESCRIPTION("Ingenic SoCs USB PHY driver"); > +MODULE_LICENSE("GPL"); > -- > 2.11.0 > ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework. 2020-09-23 17:29 ` Paul Cercueil @ 2020-09-25 15:10 ` Zhou Yanjie 0 siblings, 0 replies; 5+ messages in thread From: Zhou Yanjie @ 2020-09-25 15:10 UTC (permalink / raw) To: Paul Cercueil Cc: vkoul, kishon, gregkh, balbi, linux-kernel, linux-usb, dongsheng.qiu, aric.pzqi, rick.tyliu, yanfei.li, sernia.zhou, zhenwenjin Hi Paul, 在 2020/9/24 上午1:29, Paul Cercueil 写道: > Hi Zhou, > > Le jeu. 24 sept. 2020 à 0:26, 周琰杰 (Zhou Yanjie) > <zhouyanjie@wanyeetech.com> a écrit : >> Used the generic PHY framework API to create the PHY, this driver >> supoorts USB OTG PHY used in JZ4770 SoC, JZ4780 SoC, X1000 SoC, >> and X1830 SoC. >> >> Tested-by: 周正 (Zhou Zheng) <sernia.zhou@foxmail.com> >> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> >> Co-developed-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> >> Signed-off-by: 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> >> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> >> Reviewed-by: Paul Cercueil <paul@crapouillou.net> >> --- >> >> Notes: >> v1->v2: >> Fix bug, ".of_match_table = >> of_match_ptr(ingenic_usb_phy_of_matches)" is wrong >> and should be replaced with ".of_match_table = >> ingenic_usb_phy_of_matches". >> >> v2->v3: >> 1.Change "depends on (MACH_INGENIC && MIPS) || COMPILE_TEST" to >> "depends on MIPS || COMPILE_TEST". >> 2.Keep the adjustments of "ingenic_usb_phy_init()" and >> "ingenic_usb_phu_exit()" >> positions in v2 to make them consistent with the order in >> "ingenic_usb_phy_ops", >> keep the adjustments to the positions of >> "ingenic_usb_phy_of_matches[]" in v2 >> to keep them consistent with the styles of other USB PHY >> drivers. And remove >> some unnecessary changes to reduce the diff size, from the >> original 256 lines >> change to the current 209 lines. >> >> v3->v4: >> Only add new generic-PHY driver, without removing the old one. >> Because the >> jz4740-musb driver is not ready to use the generic PHY framework. >> When the >> jz4740-musb driver is modified to use the generic PHY framework, >> the old >> jz4770-phy driver can be "retired". >> >> v4->v5: >> 1.Add an extra blank line between "devm_of_phy_provider_register" >> and "return". >> 2.Remove unnecessary "phy_set_drvdata". >> 3.Add Paul Cercueil's Reviewed-by. >> >> v5->v6: >> 1.Revert the removal of "phy_set_drvdata" in v5, removing >> "phy_set_drvdata" will >> cause a kernel panic on CI20. >> Reported-by: H. Nikolaus Schaller <hns@goldelico.com> > > My bad, I overlooked the code of phy_set_drvdata(), indeed phy->dev > and pdev->dev are different. Sorry about that. > > With that said, you should then be able to remove the > platform_set_drvdata() call. > Sure. >> 2.Rewrite the macro definitions, replace the original code with >> "FIELD_PREP()" >> and "u32p_replace_bits()" according to Vinod Koul's suggestion. >> >> drivers/phy/Kconfig | 1 + >> drivers/phy/Makefile | 1 + >> drivers/phy/ingenic/Kconfig | 12 ++ >> drivers/phy/ingenic/Makefile | 2 + >> drivers/phy/ingenic/phy-ingenic-usb.c | 378 >> ++++++++++++++++++++++++++++++++++ >> 5 files changed, 394 insertions(+) >> create mode 100644 drivers/phy/ingenic/Kconfig >> create mode 100644 drivers/phy/ingenic/Makefile >> create mode 100644 drivers/phy/ingenic/phy-ingenic-usb.c >> >> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig >> index de9362c25c07..0534b0fdd057 100644 >> --- a/drivers/phy/Kconfig >> +++ b/drivers/phy/Kconfig >> @@ -55,6 +55,7 @@ source "drivers/phy/broadcom/Kconfig" >> source "drivers/phy/cadence/Kconfig" >> source "drivers/phy/freescale/Kconfig" >> source "drivers/phy/hisilicon/Kconfig" >> +source "drivers/phy/ingenic/Kconfig" >> source "drivers/phy/lantiq/Kconfig" >> source "drivers/phy/marvell/Kconfig" >> source "drivers/phy/mediatek/Kconfig" >> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile >> index c27408e4daae..ab24f0d20763 100644 >> --- a/drivers/phy/Makefile >> +++ b/drivers/phy/Makefile >> @@ -14,6 +14,7 @@ obj-y += allwinner/ \ >> cadence/ \ >> freescale/ \ >> hisilicon/ \ >> + ingenic/ \ >> intel/ \ >> lantiq/ \ >> marvell/ \ >> diff --git a/drivers/phy/ingenic/Kconfig b/drivers/phy/ingenic/Kconfig >> new file mode 100644 >> index 000000000000..912b14e512cb >> --- /dev/null >> +++ b/drivers/phy/ingenic/Kconfig >> @@ -0,0 +1,12 @@ >> +# SPDX-License-Identifier: GPL-2.0 >> +# >> +# Phy drivers for Ingenic platforms >> +# >> +config PHY_INGENIC_USB >> + tristate "Ingenic SoCs USB PHY Driver" >> + depends on MIPS || COMPILE_TEST >> + depends on USB_SUPPORT >> + select GENERIC_PHY >> + help >> + This driver provides USB PHY support for the USB controller found >> + on the JZ-series and X-series SoCs from Ingenic. >> diff --git a/drivers/phy/ingenic/Makefile b/drivers/phy/ingenic/Makefile >> new file mode 100644 >> index 000000000000..65d5ea00fc9d >> --- /dev/null >> +++ b/drivers/phy/ingenic/Makefile >> @@ -0,0 +1,2 @@ >> +# SPDX-License-Identifier: GPL-2.0 >> +obj-y += phy-ingenic-usb.o >> diff --git a/drivers/phy/ingenic/phy-ingenic-usb.c >> b/drivers/phy/ingenic/phy-ingenic-usb.c >> new file mode 100644 >> index 000000000000..55da6ca8faf7 >> --- /dev/null >> +++ b/drivers/phy/ingenic/phy-ingenic-usb.c >> @@ -0,0 +1,378 @@ >> +// SPDX-License-Identifier: GPL-2.0 >> +/* >> + * Ingenic SoCs USB PHY driver >> + * Copyright (c) Paul Cercueil <paul@crapouillou.net> >> + * Copyright (c) 漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com> >> + * Copyright (c) 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> >> + */ >> + >> +#include <linux/bitfield.h> >> +#include <linux/clk.h> >> +#include <linux/delay.h> >> +#include <linux/io.h> >> +#include <linux/module.h> >> +#include <linux/phy/phy.h> >> +#include <linux/platform_device.h> >> +#include <linux/regulator/consumer.h> >> + >> +/* OTGPHY register offsets */ >> +#define REG_USBPCR_OFFSET 0x00 >> +#define REG_USBRDT_OFFSET 0x04 >> +#define REG_USBVBFIL_OFFSET 0x08 >> +#define REG_USBPCR1_OFFSET 0x0c >> + >> +/* bits within the USBPCR register */ >> +#define USBPCR_USB_MODE BIT(31) >> +#define USBPCR_AVLD_REG BIT(30) >> +#define USBPCR_COMMONONN BIT(25) >> +#define USBPCR_VBUSVLDEXT BIT(24) >> +#define USBPCR_VBUSVLDEXTSEL BIT(23) >> +#define USBPCR_POR BIT(22) >> +#define USBPCR_SIDDQ BIT(21) >> +#define USBPCR_OTG_DISABLE BIT(20) >> +#define USBPCR_TXPREEMPHTUNE BIT(6) >> + >> +#define USBPCR_IDPULLUP_MASK GENMASK(29, 28) >> +#define USBPCR_IDPULLUP_ALWAYS 0x2 >> +#define USBPCR_IDPULLUP_SUSPEND 0x1 >> +#define USBPCR_IDPULLUP_OTG 0x0 >> + >> +#define USBPCR_COMPDISTUNE_MASK GENMASK(19, 17) >> +#define USBPCR_COMPDISTUNE_DFT 0x4 >> + >> +#define USBPCR_OTGTUNE_MASK GENMASK(16, 14) >> +#define USBPCR_OTGTUNE_DFT 0x4 >> + >> +#define USBPCR_SQRXTUNE_MASK GENMASK(13, 11) >> +#define USBPCR_SQRXTUNE_DCR_20PCT 0x7 >> +#define USBPCR_SQRXTUNE_DFT 0x3 >> + >> +#define USBPCR_TXFSLSTUNE_MASK GENMASK(10, 7) >> +#define USBPCR_TXFSLSTUNE_DCR_50PPT 0xf >> +#define USBPCR_TXFSLSTUNE_DCR_25PPT 0x7 >> +#define USBPCR_TXFSLSTUNE_DFT 0x3 >> +#define USBPCR_TXFSLSTUNE_INC_25PPT 0x1 >> +#define USBPCR_TXFSLSTUNE_INC_50PPT 0x0 >> + >> +#define USBPCR_TXHSXVTUNE_MASK GENMASK(5, 4) >> +#define USBPCR_TXHSXVTUNE_DFT 0x3 >> +#define USBPCR_TXHSXVTUNE_DCR_15MV 0x1 >> + >> +#define USBPCR_TXRISETUNE_MASK GENMASK(5, 4) >> +#define USBPCR_TXRISETUNE_DFT 0x3 >> + >> +#define USBPCR_TXVREFTUNE_MASK GENMASK(3, 0) >> +#define USBPCR_TXVREFTUNE_INC_25PPT 0x7 >> +#define USBPCR_TXVREFTUNE_DFT 0x5 >> + >> +/* bits within the USBRDTR register */ >> +#define USBRDT_UTMI_RST BIT(27) >> +#define USBRDT_HB_MASK BIT(26) >> +#define USBRDT_VBFIL_LD_EN BIT(25) >> +#define USBRDT_IDDIG_EN BIT(24) >> +#define USBRDT_IDDIG_REG BIT(23) >> +#define USBRDT_VBFIL_EN BIT(2) >> + >> +/* bits within the USBPCR1 register */ >> +#define USBPCR1_BVLD_REG BIT(31) >> +#define USBPCR1_DPPD BIT(29) >> +#define USBPCR1_DMPD BIT(28) >> +#define USBPCR1_USB_SEL BIT(28) >> +#define USBPCR1_WORD_IF_16BIT BIT(19) >> + >> +enum ingenic_usb_phy_version { >> + ID_JZ4770, >> + ID_JZ4780, >> + ID_X1000, >> + ID_X1830, >> +}; >> + >> +struct ingenic_soc_info { >> + enum ingenic_usb_phy_version version; >> + >> + void (*usb_phy_init)(struct phy *phy); >> +}; >> + >> +struct ingenic_usb_phy { >> + const struct ingenic_soc_info *soc_info; >> + >> + struct phy *phy; >> + struct device *dev; >> + void __iomem *base; >> + struct clk *clk; >> + struct regulator *vcc_supply; >> +}; >> + >> +static int ingenic_usb_phy_init(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + int err; >> + u32 reg; >> + >> + err = clk_prepare_enable(priv->clk); >> + if (err) { >> + dev_err(priv->dev, "Unable to start clock: %d\n", err); >> + return err; >> + } >> + >> + priv->soc_info->usb_phy_init(phy); >> + >> + /* Wait for PHY to reset */ >> + usleep_range(30, 300); >> + reg = readl(priv->base + REG_USBPCR_OFFSET); >> + writel(reg & ~USBPCR_POR, priv->base + REG_USBPCR_OFFSET); >> + usleep_range(300, 1000); >> + >> + return 0; >> +} >> + >> +static int ingenic_usb_phy_exit(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + >> + clk_disable_unprepare(priv->clk); >> + regulator_disable(priv->vcc_supply); >> + >> + return 0; >> +} >> + >> +static int ingenic_usb_phy_power_on(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + int err; >> + >> + err = regulator_enable(priv->vcc_supply); >> + if (err) { >> + dev_err(priv->dev, "Unable to enable VCC: %d\n", err); >> + return err; >> + } >> + >> + return 0; >> +} >> + >> +static int ingenic_usb_phy_power_off(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + >> + regulator_disable(priv->vcc_supply); >> + >> + return 0; >> +} >> + >> +static int ingenic_usb_phy_set_mode(struct phy *phy, >> + enum phy_mode mode, int submode) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + u32 reg; >> + >> + switch (mode) { >> + case PHY_MODE_USB_HOST: >> + reg = readl(priv->base + REG_USBPCR_OFFSET); >> + u32p_replace_bits(®, 1, USBPCR_USB_MODE); >> + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXT); >> + u32p_replace_bits(®, 0, USBPCR_VBUSVLDEXTSEL); >> + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> + >> + break; >> + case PHY_MODE_USB_DEVICE: >> + if (priv->soc_info->version >= ID_X1000) { >> + reg = readl(priv->base + REG_USBPCR1_OFFSET); >> + u32p_replace_bits(®, 1, USBPCR1_BVLD_REG); >> + writel(reg, priv->base + REG_USBPCR1_OFFSET); >> + } >> + >> + reg = readl(priv->base + REG_USBPCR_OFFSET); >> + u32p_replace_bits(®, 0, USBPCR_USB_MODE); >> + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); >> + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); >> + u32p_replace_bits(®, 1, USBPCR_OTG_DISABLE); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> + >> + break; >> + case PHY_MODE_USB_OTG: >> + reg = readl(priv->base + REG_USBPCR_OFFSET); >> + u32p_replace_bits(®, 1, USBPCR_USB_MODE); >> + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXT); >> + u32p_replace_bits(®, 1, USBPCR_VBUSVLDEXTSEL); >> + u32p_replace_bits(®, 0, USBPCR_OTG_DISABLE); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> + >> + break; >> + default: >> + return -EINVAL; >> + } >> + >> + return 0; >> +} >> + >> +static const struct phy_ops ingenic_usb_phy_ops = { >> + .init = ingenic_usb_phy_init, >> + .exit = ingenic_usb_phy_exit, >> + .power_on = ingenic_usb_phy_power_on, >> + .power_off = ingenic_usb_phy_power_off, >> + .set_mode = ingenic_usb_phy_set_mode, >> + .owner = THIS_MODULE, >> +}; >> + >> +static void jz4770_usb_phy_init(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + u32 reg; >> + >> + reg = USBPCR_AVLD_REG | USBPCR_COMMONONN | USBPCR_POR | >> + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_ALWAYS) | >> + FIELD_PREP(USBPCR_COMPDISTUNE_MASK, USBPCR_COMPDISTUNE_DFT) | >> + FIELD_PREP(USBPCR_OTGTUNE_MASK, USBPCR_OTGTUNE_DFT) | >> + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DFT) | >> + FIELD_PREP(USBPCR_TXFSLSTUNE_MASK, USBPCR_TXFSLSTUNE_DFT) | >> + FIELD_PREP(USBPCR_TXRISETUNE_MASK, USBPCR_TXRISETUNE_DFT) | >> + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, USBPCR_TXVREFTUNE_DFT); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> +} >> + >> +static void jz4780_usb_phy_init(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + u32 reg; >> + >> + reg = readl(priv->base + REG_USBPCR1_OFFSET) | USBPCR1_USB_SEL | >> + USBPCR1_WORD_IF_16BIT; >> + writel(reg, priv->base + REG_USBPCR1_OFFSET); >> + >> + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR; >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> +} >> + >> +static void x1000_usb_phy_init(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + u32 reg; >> + >> + reg = readl(priv->base + REG_USBPCR1_OFFSET) | >> USBPCR1_WORD_IF_16BIT; >> + writel(reg, priv->base + REG_USBPCR1_OFFSET); >> + >> + reg = USBPCR_TXPREEMPHTUNE | USBPCR_COMMONONN | USBPCR_POR | >> + FIELD_PREP(USBPCR_SQRXTUNE_MASK, USBPCR_SQRXTUNE_DCR_20PCT) | >> + FIELD_PREP(USBPCR_TXHSXVTUNE_MASK, >> USBPCR_TXHSXVTUNE_DCR_15MV) | >> + FIELD_PREP(USBPCR_TXVREFTUNE_MASK, >> USBPCR_TXVREFTUNE_INC_25PPT); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> +} >> + >> +static void x1830_usb_phy_init(struct phy *phy) >> +{ >> + struct ingenic_usb_phy *priv = phy_get_drvdata(phy); >> + u32 reg; >> + >> + /* rdt */ >> + writel(USBRDT_VBFIL_EN | USBRDT_UTMI_RST, priv->base + >> REG_USBRDT_OFFSET); >> + >> + reg = readl(priv->base + REG_USBPCR1_OFFSET) | >> USBPCR1_WORD_IF_16BIT | >> + USBPCR1_DMPD | USBPCR1_DPPD; >> + writel(reg, priv->base + REG_USBPCR1_OFFSET); >> + >> + reg = USBPCR_VBUSVLDEXT | USBPCR_TXPREEMPHTUNE | >> USBPCR_COMMONONN | USBPCR_POR | > > There's a stray tab character here. > I will fix this in v7. >> + FIELD_PREP(USBPCR_IDPULLUP_MASK, USBPCR_IDPULLUP_OTG); >> + writel(reg, priv->base + REG_USBPCR_OFFSET); >> +} >> + >> +static const struct ingenic_soc_info jz4770_soc_info = { >> + .version = ID_JZ4770, >> + >> + .usb_phy_init = jz4770_usb_phy_init, >> +}; >> + >> +static const struct ingenic_soc_info jz4780_soc_info = { >> + .version = ID_JZ4780, >> + >> + .usb_phy_init = jz4780_usb_phy_init, >> +}; >> + >> +static const struct ingenic_soc_info x1000_soc_info = { >> + .version = ID_X1000, >> + >> + .usb_phy_init = x1000_usb_phy_init, >> +}; >> + >> +static const struct ingenic_soc_info x1830_soc_info = { >> + .version = ID_X1830, >> + >> + .usb_phy_init = x1830_usb_phy_init, >> +}; >> + >> +static int ingenic_usb_phy_probe(struct platform_device *pdev) >> +{ >> + struct ingenic_usb_phy *priv; >> + struct phy_provider *provider; >> + struct device *dev = &pdev->dev; >> + int err; >> + >> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); >> + if (!priv) >> + return -ENOMEM; >> + >> + priv->soc_info = device_get_match_data(dev); >> + if (!priv->soc_info) { >> + dev_err(dev, "Error: No device match found\n"); >> + return -ENODEV; >> + } >> + >> + platform_set_drvdata(pdev, priv); > > You should be able to remove the platform_set_drvdata() here. Not the > phy_set_drvdata() ;) > Sure. >> + priv->dev = dev; > > You may also remove the "dev" field in your priv structure, and use > &phy->dev instead, from what I can see it's only used in your > dev_err() calls. Not a deal-breaker though, I'm fine with both. > Sure. >> + >> + priv->base = devm_platform_ioremap_resource(pdev, 0); >> + if (IS_ERR(priv->base)) { >> + dev_err(dev, "Failed to map registers\n"); >> + return PTR_ERR(priv->base); >> + } >> + >> + priv->clk = devm_clk_get(dev, NULL); >> + if (IS_ERR(priv->clk)) { >> + err = PTR_ERR(priv->clk); >> + if (err != -EPROBE_DEFER) >> + dev_err(dev, "Failed to get clock\n"); >> + return err; > > You can do: > > if (IS_ERR(priv->clk)) > return dev_err_probe(dev, PTR_ERR(priv->clk), "Failed to get > clock\n"); > > if Vinod is okay with that (I know some maintainers don't like it). > Sure, if Vinod feel it is okay, I will make changes in v7. Thanks and best regards! >> + } >> + >> + priv->vcc_supply = devm_regulator_get(dev, "vcc"); >> + if (IS_ERR(priv->vcc_supply)) { >> + err = PTR_ERR(priv->vcc_supply); >> + if (err != -EPROBE_DEFER) >> + dev_err(dev, "Failed to get regulator\n"); >> + return err; > > Same here. > > These are nitpicks though and I'm happy with the V6 being merged. > > Cheers, > -Paul > >> + } >> + >> + priv->phy = devm_phy_create(dev, NULL, &ingenic_usb_phy_ops); >> + if (IS_ERR(priv)) >> + return PTR_ERR(priv); >> + >> + phy_set_drvdata(priv->phy, priv); >> + >> + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); >> + >> + return PTR_ERR_OR_ZERO(provider); >> +} >> + >> +static const struct of_device_id ingenic_usb_phy_of_matches[] = { >> + { .compatible = "ingenic,jz4770-phy", .data = &jz4770_soc_info }, >> + { .compatible = "ingenic,jz4780-phy", .data = &jz4780_soc_info }, >> + { .compatible = "ingenic,x1000-phy", .data = &x1000_soc_info }, >> + { .compatible = "ingenic,x1830-phy", .data = &x1830_soc_info }, >> + { /* sentinel */ } >> +}; >> +MODULE_DEVICE_TABLE(of, ingenic_usb_phy_of_matches); >> + >> +static struct platform_driver ingenic_usb_phy_driver = { >> + .probe = ingenic_usb_phy_probe, >> + .driver = { >> + .name = "ingenic-usb-phy", >> + .of_match_table = ingenic_usb_phy_of_matches, >> + }, >> +}; >> +module_platform_driver(ingenic_usb_phy_driver); >> + >> +MODULE_AUTHOR("周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>"); >> +MODULE_AUTHOR("漆鹏振 (Qi Pengzhen) <aric.pzqi@ingenic.com>"); >> +MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>"); >> +MODULE_DESCRIPTION("Ingenic SoCs USB PHY driver"); >> +MODULE_LICENSE("GPL"); >> -- >> 2.11.0 >> > ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2020-09-25 15:11 UTC | newest] Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2020-09-23 16:25 [PATCH v6 0/2] Use the generic PHY framework for Ingenic USB PHY 周琰杰 (Zhou Yanjie) 2020-09-23 16:25 ` [PATCH v6 1/2] USB: PHY: JZ4770: Remove unnecessary function calls 周琰杰 (Zhou Yanjie) 2020-09-23 16:26 ` [PATCH v6 2/2] PHY: Ingenic: Add USB PHY driver using generic PHY framework 周琰杰 (Zhou Yanjie) 2020-09-23 17:29 ` Paul Cercueil 2020-09-25 15:10 ` Zhou Yanjie
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).