linux-watchdog.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Guenter Roeck <linux@roeck-us.net>
To: Paul Cercueil <paul@crapouillou.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>,
	od@zcrc.me, linux-watchdog@vger.kernel.org,
	linux-kernel@vger.kernel.org,
	Mathieu Malaterre <malat@debian.org>,
	Artur Rojek <contact@artur-rojek.eu>
Subject: Re: [PATCH 1/3] watchdog: jz4740: Use WDT clock provided by TCU driver
Date: Fri, 9 Aug 2019 10:58:19 -0700	[thread overview]
Message-ID: <20190809175819.GA23562@roeck-us.net> (raw)
In-Reply-To: <20190809115930.6050-2-paul@crapouillou.net>

On Fri, Aug 09, 2019 at 01:59:28PM +0200, Paul Cercueil wrote:
> Instead of requesting the "ext" clock and handling the watchdog clock
> divider and gating in the watchdog driver, we now request and use the
> "wdt" clock that is supplied by the ingenic-timer "TCU" driver.
> 
> The major benefit is that the watchdog's clock rate and parent can now
> be specified from within devicetree, instead of hardcoded in the driver.
> 
> Also, this driver won't poke anymore into the TCU registers to
> enable/disable the clock, as this is now handled by the TCU driver.
> 
> On the bad side, we break the ABI with devicetree - as we now request a
> different clock. In this very specific case it is still okay, as every
> Ingenic JZ47xx-based board out there compile the devicetree within the
> kernel; so it's still time to push breaking changes, in order to get a
> clean devicetree that won't break once it musn't.
> 
> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> Tested-by: Mathieu Malaterre <malat@debian.org>
> Tested-by: Artur Rojek <contact@artur-rojek.eu>

Acked-by: Guenter Roeck <linux@roeck-us.net>

> ---
>  drivers/watchdog/Kconfig      |  1 +
>  drivers/watchdog/jz4740_wdt.c | 75 ++++++++++++++---------------------
>  2 files changed, 31 insertions(+), 45 deletions(-)
> 
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index 8188963a405b..820d8a472310 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -1645,6 +1645,7 @@ config INDYDOG
>  config JZ4740_WDT
>  	tristate "Ingenic jz4740 SoC hardware watchdog"
>  	depends on MACH_JZ4740 || MACH_JZ4780
> +	depends on COMMON_CLK
>  	select WATCHDOG_CORE
>  	help
>  	  Hardware driver for the built-in watchdog timer on Ingenic jz4740 SoCs.
> diff --git a/drivers/watchdog/jz4740_wdt.c b/drivers/watchdog/jz4740_wdt.c
> index d4a90916dd38..07fbd9d96e84 100644
> --- a/drivers/watchdog/jz4740_wdt.c
> +++ b/drivers/watchdog/jz4740_wdt.c
> @@ -18,19 +18,6 @@
>  #include <linux/err.h>
>  #include <linux/of.h>
>  
> -#include <asm/mach-jz4740/timer.h>
> -
> -#define JZ_WDT_CLOCK_PCLK 0x1
> -#define JZ_WDT_CLOCK_RTC  0x2
> -#define JZ_WDT_CLOCK_EXT  0x4
> -
> -#define JZ_WDT_CLOCK_DIV_1    (0 << TCU_TCSR_PRESCALE_LSB)
> -#define JZ_WDT_CLOCK_DIV_4    (1 << TCU_TCSR_PRESCALE_LSB)
> -#define JZ_WDT_CLOCK_DIV_16   (2 << TCU_TCSR_PRESCALE_LSB)
> -#define JZ_WDT_CLOCK_DIV_64   (3 << TCU_TCSR_PRESCALE_LSB)
> -#define JZ_WDT_CLOCK_DIV_256  (4 << TCU_TCSR_PRESCALE_LSB)
> -#define JZ_WDT_CLOCK_DIV_1024 (5 << TCU_TCSR_PRESCALE_LSB)
> -
>  #define DEFAULT_HEARTBEAT 5
>  #define MAX_HEARTBEAT     2048
>  
> @@ -50,7 +37,8 @@ MODULE_PARM_DESC(heartbeat,
>  struct jz4740_wdt_drvdata {
>  	struct watchdog_device wdt;
>  	void __iomem *base;
> -	struct clk *rtc_clk;
> +	struct clk *clk;
> +	unsigned long clk_rate;
>  };
>  
>  static int jz4740_wdt_ping(struct watchdog_device *wdt_dev)
> @@ -65,32 +53,14 @@ static int jz4740_wdt_set_timeout(struct watchdog_device *wdt_dev,
>  				    unsigned int new_timeout)
>  {
>  	struct jz4740_wdt_drvdata *drvdata = watchdog_get_drvdata(wdt_dev);
> -	unsigned int rtc_clk_rate;
> -	unsigned int timeout_value;
> -	unsigned short clock_div = JZ_WDT_CLOCK_DIV_1;
> +	u16 timeout_value = (u16)(drvdata->clk_rate * new_timeout);
>  	u8 tcer;
>  
> -	rtc_clk_rate = clk_get_rate(drvdata->rtc_clk);
> -
> -	timeout_value = rtc_clk_rate * new_timeout;
> -	while (timeout_value > 0xffff) {
> -		if (clock_div == JZ_WDT_CLOCK_DIV_1024) {
> -			/* Requested timeout too high;
> -			* use highest possible value. */
> -			timeout_value = 0xffff;
> -			break;
> -		}
> -		timeout_value >>= 2;
> -		clock_div += (1 << TCU_TCSR_PRESCALE_LSB);
> -	}
> -
>  	tcer = readb(drvdata->base + TCU_REG_WDT_TCER);
>  	writeb(0x0, drvdata->base + TCU_REG_WDT_TCER);
> -	writew(clock_div, drvdata->base + TCU_REG_WDT_TCSR);
>  
>  	writew((u16)timeout_value, drvdata->base + TCU_REG_WDT_TDR);
>  	writew(0x0, drvdata->base + TCU_REG_WDT_TCNT);
> -	writew(clock_div | JZ_WDT_CLOCK_RTC, drvdata->base + TCU_REG_WDT_TCSR);
>  
>  	if (tcer & TCU_WDT_TCER_TCEN)
>  		writeb(TCU_WDT_TCER_TCEN, drvdata->base + TCU_REG_WDT_TCER);
> @@ -102,11 +72,15 @@ static int jz4740_wdt_set_timeout(struct watchdog_device *wdt_dev,
>  static int jz4740_wdt_start(struct watchdog_device *wdt_dev)
>  {
>  	struct jz4740_wdt_drvdata *drvdata = watchdog_get_drvdata(wdt_dev);
> +	int ret;
>  	u8 tcer;
>  
> +	ret = clk_prepare_enable(drvdata->clk);
> +	if (ret)
> +		return ret;
> +
>  	tcer = readb(drvdata->base + TCU_REG_WDT_TCER);
>  
> -	jz4740_timer_enable_watchdog();
>  	jz4740_wdt_set_timeout(wdt_dev, wdt_dev->timeout);
>  
>  	/* Start watchdog if it wasn't started already */
> @@ -121,7 +95,7 @@ static int jz4740_wdt_stop(struct watchdog_device *wdt_dev)
>  	struct jz4740_wdt_drvdata *drvdata = watchdog_get_drvdata(wdt_dev);
>  
>  	writeb(0x0, drvdata->base + TCU_REG_WDT_TCER);
> -	jz4740_timer_disable_watchdog();
> +	clk_disable_unprepare(drvdata->clk);
>  
>  	return 0;
>  }
> @@ -162,6 +136,8 @@ static int jz4740_wdt_probe(struct platform_device *pdev)
>  	struct device *dev = &pdev->dev;
>  	struct jz4740_wdt_drvdata *drvdata;
>  	struct watchdog_device *jz4740_wdt;
> +	struct resource	*res;
> +	long rate;
>  	int ret;
>  
>  	drvdata = devm_kzalloc(dev, sizeof(struct jz4740_wdt_drvdata),
> @@ -169,15 +145,30 @@ static int jz4740_wdt_probe(struct platform_device *pdev)
>  	if (!drvdata)
>  		return -ENOMEM;
>  
> -	if (heartbeat < 1 || heartbeat > MAX_HEARTBEAT)
> -		heartbeat = DEFAULT_HEARTBEAT;
> +	drvdata->clk = devm_clk_get(&pdev->dev, "wdt");
> +	if (IS_ERR(drvdata->clk)) {
> +		dev_err(&pdev->dev, "cannot find WDT clock\n");
> +		return PTR_ERR(drvdata->clk);
> +	}
> +
> +	/* Set smallest clock possible */
> +	rate = clk_round_rate(drvdata->clk, 1);
> +	if (rate < 0)
> +		return rate;
>  
> +	ret = clk_set_rate(drvdata->clk, rate);
> +	if (ret)
> +		return ret;
> +
> +	drvdata->clk_rate = rate;
>  	jz4740_wdt = &drvdata->wdt;
>  	jz4740_wdt->info = &jz4740_wdt_info;
>  	jz4740_wdt->ops = &jz4740_wdt_ops;
> -	jz4740_wdt->timeout = heartbeat;
>  	jz4740_wdt->min_timeout = 1;
> -	jz4740_wdt->max_timeout = MAX_HEARTBEAT;
> +	jz4740_wdt->max_timeout = 0xffff / rate;
> +	jz4740_wdt->timeout = clamp(heartbeat,
> +				    jz4740_wdt->min_timeout,
> +				    jz4740_wdt->max_timeout);
>  	jz4740_wdt->parent = dev;
>  	watchdog_set_nowayout(jz4740_wdt, nowayout);
>  	watchdog_set_drvdata(jz4740_wdt, drvdata);
> @@ -186,12 +177,6 @@ static int jz4740_wdt_probe(struct platform_device *pdev)
>  	if (IS_ERR(drvdata->base))
>  		return PTR_ERR(drvdata->base);
>  
> -	drvdata->rtc_clk = devm_clk_get(dev, "rtc");
> -	if (IS_ERR(drvdata->rtc_clk)) {
> -		dev_err(dev, "cannot find RTC clock\n");
> -		return PTR_ERR(drvdata->rtc_clk);
> -	}
> -
>  	return devm_watchdog_register_device(dev, &drvdata->wdt);
>  }
>  

  reply	other threads:[~2019-08-09 17:58 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-08-09 11:59 [PATCH 0/3] watchdog: jz4740: Driver update Paul Cercueil
2019-08-09 11:59 ` [PATCH 1/3] watchdog: jz4740: Use WDT clock provided by TCU driver Paul Cercueil
2019-08-09 17:58   ` Guenter Roeck [this message]
2019-08-09 11:59 ` [PATCH 2/3] watchdog: jz4740: Use regmap " Paul Cercueil
2019-08-09 17:58   ` Guenter Roeck
2019-08-09 11:59 ` [PATCH 3/3] watchdog: jz4740: Drop dependency on MACH_JZ47xx Paul Cercueil
2019-08-09 17:59   ` Guenter Roeck
2019-08-09 16:52 ` [PATCH 0/3] watchdog: jz4740: Driver update Guenter Roeck
2019-08-09 16:55   ` Paul Cercueil
2019-08-09 17:29     ` Guenter Roeck
2019-08-09 17:34       ` Paul Cercueil
2019-08-09 17:57         ` Guenter Roeck

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190809175819.GA23562@roeck-us.net \
    --to=linux@roeck-us.net \
    --cc=contact@artur-rojek.eu \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-watchdog@vger.kernel.org \
    --cc=malat@debian.org \
    --cc=od@zcrc.me \
    --cc=paul@crapouillou.net \
    --cc=wim@linux-watchdog.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).