* [PATCH 01/10] iwlwifi: mvm: fix antenna selection when BT is active
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 02/10] iwlwifi: mvm: Avoid accessing Null pointer when setting igtk Emmanuel Grumbach
` (9 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Emmanuel Grumbach, stable
When BT is active, we want to avoid the shared antenna for
management frame to make sure we don't disturb BT. There
was a bug in that code because it chose the antenna
BIT(ANT_A) where ANT_A is already a bitmap (0x1). This
means that the antenna chosen in the end was ANT_B.
While this is not optimal on devices with 2 antennas (it'd
disturb BT), it is critical on single antenna devices like
3160 which couldn't connect at all when BT was active.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=97181
CC: <stable@vger.kernel.org> [3.17+]
Fixes: 34c8b24ff284 ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/mvm/tx.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/iwlwifi/mvm/tx.c b/drivers/net/wireless/iwlwifi/mvm/tx.c
index 7ba7a118..8911686 100644
--- a/drivers/net/wireless/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/iwlwifi/mvm/tx.c
@@ -252,7 +252,7 @@ void iwl_mvm_set_tx_cmd_rate(struct iwl_mvm *mvm, struct iwl_tx_cmd *tx_cmd,
if (info->band == IEEE80211_BAND_2GHZ &&
!iwl_mvm_bt_coex_is_shared_ant_avail(mvm))
- rate_flags = BIT(mvm->cfg->non_shared_ant) << RATE_MCS_ANT_POS;
+ rate_flags = mvm->cfg->non_shared_ant << RATE_MCS_ANT_POS;
else
rate_flags =
BIT(mvm->mgmt_last_antenna_idx) << RATE_MCS_ANT_POS;
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 02/10] iwlwifi: mvm: Avoid accessing Null pointer when setting igtk
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
2015-07-12 17:08 ` [PATCH 01/10] iwlwifi: mvm: fix antenna selection when BT is active Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 03/10] iwlwifi: pcie: Fix bug in NIC's PM registers access Emmanuel Grumbach
` (8 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Matti Gottlieb, Emmanuel Grumbach
From: Matti Gottlieb <matti.gottlieb@intel.com>
Sometimes when setting an igtk key the station maybe NULL.
In the of case igtk the function will skip to the end, and
try to print sta->addr, if sta is Null - we will access a
Null pointer.
Avoid accessing a Null pointer when setting a igtk key &
the sta == NULL, and print a default MAC address instead.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/mvm/sta.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/iwlwifi/mvm/sta.c b/drivers/net/wireless/iwlwifi/mvm/sta.c
index d68dc69..26f076e 100644
--- a/drivers/net/wireless/iwlwifi/mvm/sta.c
+++ b/drivers/net/wireless/iwlwifi/mvm/sta.c
@@ -1401,6 +1401,7 @@ int iwl_mvm_set_sta_key(struct iwl_mvm *mvm,
bool mcast = !(keyconf->flags & IEEE80211_KEY_FLAG_PAIRWISE);
u8 sta_id;
int ret;
+ static const u8 __maybe_unused zero_addr[ETH_ALEN] = {0};
lockdep_assert_held(&mvm->mutex);
@@ -1467,7 +1468,7 @@ int iwl_mvm_set_sta_key(struct iwl_mvm *mvm,
end:
IWL_DEBUG_WEP(mvm, "key: cipher=%x len=%d idx=%d sta=%pM ret=%d\n",
keyconf->cipher, keyconf->keylen, keyconf->keyidx,
- sta->addr, ret);
+ sta ? sta->addr : zero_addr, ret);
return ret;
}
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 03/10] iwlwifi: pcie: Fix bug in NIC's PM registers access
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
2015-07-12 17:08 ` [PATCH 01/10] iwlwifi: mvm: fix antenna selection when BT is active Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 02/10] iwlwifi: mvm: Avoid accessing Null pointer when setting igtk Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 04/10] iwlwifi: pcie: don't panic if pcie transport alloc fails Emmanuel Grumbach
` (7 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Dreyfuss, Haim, Emmanuel Grumbach
From: "Dreyfuss, Haim" <haim.dreyfuss@intel.com>
While cleanig the access to those hw-dependent registers,
instead of using the product family type, wrong condition was added
mistakenly and enabled 8000 family devices a forbidden access
to HW registers, fix it.
Fixes: 95411d0455cc ("iwlwifi: pcie: Control access to the NIC's PM registers via iwl_cfg")
Signed-off-by: Dreyfuss, Haim <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/pcie/trans.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index 43ae658..608ba1e 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -182,7 +182,7 @@ static void iwl_trans_pcie_write_shr(struct iwl_trans *trans, u32 reg, u32 val)
static void iwl_pcie_set_pwr(struct iwl_trans *trans, bool vaux)
{
- if (!trans->cfg->apmg_not_supported)
+ if (trans->cfg->apmg_not_supported)
return;
if (vaux && pci_pme_capable(to_pci_dev(trans->dev), PCI_D3cold))
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 04/10] iwlwifi: pcie: don't panic if pcie transport alloc fails
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (2 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 03/10] iwlwifi: pcie: Fix bug in NIC's PM registers access Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 05/10] iwlwifi: pcie: prepare the device before accessing it Emmanuel Grumbach
` (6 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Emmanuel Grumbach, stable
iwl_trans_pcie_alloc needs to return a non-zero value
if it fails. Otherwise the iwl_drv_start will think that
the allocation succeeded.
Remove the duplication of err and ret variable and use ret
which is the name we usually use in other places of the
driver.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/pcie/trans.c | 44 +++++++++++++++----------------
1 file changed, 22 insertions(+), 22 deletions(-)
diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index 608ba1e..fe61d0a 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -2459,7 +2459,7 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
struct iwl_trans_pcie *trans_pcie;
struct iwl_trans *trans;
u16 pci_cmd;
- int err;
+ int ret;
trans = iwl_trans_alloc(sizeof(struct iwl_trans_pcie),
&pdev->dev, cfg, &trans_ops_pcie, 0);
@@ -2474,8 +2474,8 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
spin_lock_init(&trans_pcie->ref_lock);
init_waitqueue_head(&trans_pcie->ucode_write_waitq);
- err = pci_enable_device(pdev);
- if (err)
+ ret = pci_enable_device(pdev);
+ if (ret)
goto out_no_pci;
if (!cfg->base_params->pcie_l1_allowed) {
@@ -2491,23 +2491,23 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
pci_set_master(pdev);
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(36));
- if (!err)
- err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(36));
- if (err) {
- err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
- if (!err)
- err = pci_set_consistent_dma_mask(pdev,
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(36));
+ if (!ret)
+ ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(36));
+ if (ret) {
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (!ret)
+ ret = pci_set_consistent_dma_mask(pdev,
DMA_BIT_MASK(32));
/* both attempts failed: */
- if (err) {
+ if (ret) {
dev_err(&pdev->dev, "No suitable DMA available\n");
goto out_pci_disable_device;
}
}
- err = pci_request_regions(pdev, DRV_NAME);
- if (err) {
+ ret = pci_request_regions(pdev, DRV_NAME);
+ if (ret) {
dev_err(&pdev->dev, "pci_request_regions failed\n");
goto out_pci_disable_device;
}
@@ -2515,7 +2515,7 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
trans_pcie->hw_base = pci_ioremap_bar(pdev, 0);
if (!trans_pcie->hw_base) {
dev_err(&pdev->dev, "pci_ioremap_bar failed\n");
- err = -ENODEV;
+ ret = -ENODEV;
goto out_pci_release_regions;
}
@@ -2527,9 +2527,9 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
trans_pcie->pci_dev = pdev;
iwl_disable_interrupts(trans);
- err = pci_enable_msi(pdev);
- if (err) {
- dev_err(&pdev->dev, "pci_enable_msi failed(0X%x)\n", err);
+ ret = pci_enable_msi(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "pci_enable_msi failed(0X%x)\n", ret);
/* enable rfkill interrupt: hw bug w/a */
pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd);
if (pci_cmd & PCI_COMMAND_INTX_DISABLE) {
@@ -2547,7 +2547,6 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
*/
if (trans->cfg->device_family == IWL_DEVICE_FAMILY_8000) {
unsigned long flags;
- int ret;
trans->hw_rev = (trans->hw_rev & 0xfff0) |
(CSR_HW_REV_STEP(trans->hw_rev << 2) << 2);
@@ -2591,13 +2590,14 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
/* Initialize the wait queue for commands */
init_waitqueue_head(&trans_pcie->wait_command_queue);
- if (iwl_pcie_alloc_ict(trans))
+ ret = iwl_pcie_alloc_ict(trans);
+ if (ret)
goto out_pci_disable_msi;
- err = request_threaded_irq(pdev->irq, iwl_pcie_isr,
+ ret = request_threaded_irq(pdev->irq, iwl_pcie_isr,
iwl_pcie_irq_handler,
IRQF_SHARED, DRV_NAME, trans);
- if (err) {
+ if (ret) {
IWL_ERR(trans, "Error allocating IRQ %d\n", pdev->irq);
goto out_free_ict;
}
@@ -2617,5 +2617,5 @@ out_pci_disable_device:
pci_disable_device(pdev);
out_no_pci:
iwl_trans_free(trans);
- return ERR_PTR(err);
+ return ERR_PTR(ret);
}
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 05/10] iwlwifi: pcie: prepare the device before accessing it
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (3 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 04/10] iwlwifi: pcie: don't panic if pcie transport alloc fails Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 06/10] iwlwifi: mvm: check time-event vif to avoid bad deletion Emmanuel Grumbach
` (5 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Emmanuel Grumbach, stable
For 8000 series, we need to access the device to know what
firmware to load. Before we do so, we need to prepare the
device otherwise we might not be able to access the
hardware.
Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps")
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/pcie/trans.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index fe61d0a..6203c4a 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -2551,6 +2551,12 @@ struct iwl_trans *iwl_trans_pcie_alloc(struct pci_dev *pdev,
trans->hw_rev = (trans->hw_rev & 0xfff0) |
(CSR_HW_REV_STEP(trans->hw_rev << 2) << 2);
+ ret = iwl_pcie_prepare_card_hw(trans);
+ if (ret) {
+ IWL_WARN(trans, "Exit HW not ready\n");
+ goto out_pci_disable_msi;
+ }
+
/*
* in-order to recognize C step driver should read chip version
* id located at the AUX bus MISC address space.
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 06/10] iwlwifi: mvm: check time-event vif to avoid bad deletion
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (4 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 05/10] iwlwifi: pcie: prepare the device before accessing it Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 07/10] iwlwifi: edit the 3165 series and 8000 series PCI IDs Emmanuel Grumbach
` (4 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Johannes Berg, Emmanuel Grumbach
From: Johannes Berg <johannes.berg@intel.com>
The time event is initialized relatively late in interface (mvmvif)
initialization, so it's possible to fail before that happens. As a
consequence, the driver will crash if it ever tries to delete this
time event in case initialization was unsuccessful.
Avoid this by using the time event's vif pointer to indicate validity.
The vif pointer is != NULL whenever the id is != TE_MAX, except for
this special error case where the vif pointer will have the correct
property (as the whole memory is cleared on allocation) whereas the
id is 0, causing a crash in trying to delete the time event from the
list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/mvm/time-event.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/iwlwifi/mvm/time-event.c b/drivers/net/wireless/iwlwifi/mvm/time-event.c
index d24b6a8..e472729 100644
--- a/drivers/net/wireless/iwlwifi/mvm/time-event.c
+++ b/drivers/net/wireless/iwlwifi/mvm/time-event.c
@@ -86,7 +86,7 @@ void iwl_mvm_te_clear_data(struct iwl_mvm *mvm,
{
lockdep_assert_held(&mvm->time_event_lock);
- if (te_data->id == TE_MAX)
+ if (!te_data->vif)
return;
list_del(&te_data->list);
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 07/10] iwlwifi: edit the 3165 series and 8000 series PCI IDs
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (5 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 06/10] iwlwifi: mvm: check time-event vif to avoid bad deletion Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-17 8:15 ` Kalle Valo
2015-07-12 17:08 ` [PATCH 08/10] iwlwifi: mvm: Add preemptive flag to scheulded scan Emmanuel Grumbach
` (3 subsequent siblings)
10 siblings, 1 reply; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Oren Givon, Emmanuel Grumbach
From: Oren Givon <oren.givon@intel.com>
Add new 3165 devices support.
Add one new 8000 series device support.
Remove support for 0x0000, 0xC030 and 0xD030 sub-system IDs
in the 8000 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/pcie/drv.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/iwlwifi/pcie/drv.c b/drivers/net/wireless/iwlwifi/pcie/drv.c
index 2ed1e4d..9f65c1c 100644
--- a/drivers/net/wireless/iwlwifi/pcie/drv.c
+++ b/drivers/net/wireless/iwlwifi/pcie/drv.c
@@ -368,12 +368,14 @@ static const struct pci_device_id iwl_hw_card_ids[] = {
/* 3165 Series */
{IWL_PCI_DEVICE(0x3165, 0x4010, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3165, 0x4012, iwl3165_2ac_cfg)},
+ {IWL_PCI_DEVICE(0x3166, 0x4212, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3165, 0x4410, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3165, 0x4510, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3165, 0x4110, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3166, 0x4310, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3166, 0x4210, iwl3165_2ac_cfg)},
{IWL_PCI_DEVICE(0x3165, 0x8010, iwl3165_2ac_cfg)},
+ {IWL_PCI_DEVICE(0x3165, 0x8110, iwl3165_2ac_cfg)},
/* 7265 Series */
{IWL_PCI_DEVICE(0x095A, 0x5010, iwl7265_2ac_cfg)},
@@ -426,9 +428,8 @@ static const struct pci_device_id iwl_hw_card_ids[] = {
{IWL_PCI_DEVICE(0x24F4, 0x1130, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F4, 0x1030, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F3, 0xC010, iwl8260_2ac_cfg)},
+ {IWL_PCI_DEVICE(0x24F3, 0xC110, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F3, 0xD010, iwl8260_2ac_cfg)},
- {IWL_PCI_DEVICE(0x24F4, 0xC030, iwl8260_2ac_cfg)},
- {IWL_PCI_DEVICE(0x24F4, 0xD030, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F3, 0xC050, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F3, 0xD050, iwl8260_2ac_cfg)},
{IWL_PCI_DEVICE(0x24F3, 0x8010, iwl8260_2ac_cfg)},
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 08/10] iwlwifi: mvm: Add preemptive flag to scheulded scan
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (6 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 07/10] iwlwifi: edit the 3165 series and 8000 series PCI IDs Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 09/10] Revert "iwlwifi: pcie: New RBD allocation model" Emmanuel Grumbach
` (2 subsequent siblings)
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Avraham Stern, Emmanuel Grumbach
From: Avraham Stern <avraham.stern@intel.com>
Add preemptive flag to scheduled scan command flags. Without this
flag, all scan requests after scheduled scan was started will be
delayed until scheduled scan stops. As a result, P2P_FIND will be
blocked while scheduled scan is active.
This flag was omitted during refactoring.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h | 3 ++-
drivers/net/wireless/iwlwifi/mvm/scan.c | 3 +++
2 files changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h b/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
index 5e4cbdb..737774a 100644
--- a/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
+++ b/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
@@ -660,7 +660,8 @@ struct iwl_scan_config {
* iwl_umac_scan_flags
*@IWL_UMAC_SCAN_FLAG_PREEMPTIVE: scan process triggered by this scan request
* can be preempted by other scan requests with higher priority.
- * The low priority scan is aborted.
+ * The low priority scan will be resumed when the higher proirity scan is
+ * completed.
*@IWL_UMAC_SCAN_FLAG_START_NOTIF: notification will be sent to the driver
* when scan starts.
*/
diff --git a/drivers/net/wireless/iwlwifi/mvm/scan.c b/drivers/net/wireless/iwlwifi/mvm/scan.c
index 5de1449..5000bfcd 100644
--- a/drivers/net/wireless/iwlwifi/mvm/scan.c
+++ b/drivers/net/wireless/iwlwifi/mvm/scan.c
@@ -1109,6 +1109,9 @@ static int iwl_mvm_scan_umac(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
cmd->uid = cpu_to_le32(uid);
cmd->general_flags = cpu_to_le32(iwl_mvm_scan_umac_flags(mvm, params));
+ if (type == IWL_MVM_SCAN_SCHED)
+ cmd->flags = cpu_to_le32(IWL_UMAC_SCAN_FLAG_PREEMPTIVE);
+
if (iwl_mvm_scan_use_ebs(mvm, vif, n_iterations))
cmd->channel_flags = IWL_SCAN_CHANNEL_FLAG_EBS |
IWL_SCAN_CHANNEL_FLAG_EBS_ACCURATE |
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 09/10] Revert "iwlwifi: pcie: New RBD allocation model"
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (7 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 08/10] iwlwifi: mvm: Add preemptive flag to scheulded scan Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-12 17:08 ` [PATCH 10/10] iwlwifi: nvm: remove mac address byte swapping in 8000 family Emmanuel Grumbach
2015-07-17 8:26 ` pull request: iwlwifi 2015-06-15 Kalle Valo
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Emmanuel Grumbach
This reverts commit 5f17570354f91275b0a37a4da33d29a2ab57d32e.
This patch introduced a high latency in buffer allocation
under extreme load. This latency caused a firmwre crash.
The same scenario works fine with this patch reverted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/iwl-fh.h | 6 +
drivers/net/wireless/iwlwifi/pcie/internal.h | 51 +---
drivers/net/wireless/iwlwifi/pcie/rx.c | 414 ++++++---------------------
3 files changed, 97 insertions(+), 374 deletions(-)
diff --git a/drivers/net/wireless/iwlwifi/iwl-fh.h b/drivers/net/wireless/iwlwifi/iwl-fh.h
index d560648..d45dc02 100644
--- a/drivers/net/wireless/iwlwifi/iwl-fh.h
+++ b/drivers/net/wireless/iwlwifi/iwl-fh.h
@@ -438,6 +438,12 @@ static inline unsigned int FH_MEM_CBBC_QUEUE(unsigned int chnl)
#define RX_QUEUE_MASK 255
#define RX_QUEUE_SIZE_LOG 8
+/*
+ * RX related structures and functions
+ */
+#define RX_FREE_BUFFERS 64
+#define RX_LOW_WATERMARK 8
+
/**
* struct iwl_rb_status - reserve buffer status
* host memory mapped FH registers
diff --git a/drivers/net/wireless/iwlwifi/pcie/internal.h b/drivers/net/wireless/iwlwifi/pcie/internal.h
index 31f72a6..376b84e 100644
--- a/drivers/net/wireless/iwlwifi/pcie/internal.h
+++ b/drivers/net/wireless/iwlwifi/pcie/internal.h
@@ -44,15 +44,6 @@
#include "iwl-io.h"
#include "iwl-op-mode.h"
-/*
- * RX related structures and functions
- */
-#define RX_NUM_QUEUES 1
-#define RX_POST_REQ_ALLOC 2
-#define RX_CLAIM_REQ_ALLOC 8
-#define RX_POOL_SIZE ((RX_CLAIM_REQ_ALLOC - RX_POST_REQ_ALLOC) * RX_NUM_QUEUES)
-#define RX_LOW_WATERMARK 8
-
struct iwl_host_cmd;
/*This file includes the declaration that are internal to the
@@ -86,29 +77,29 @@ struct isr_statistics {
* struct iwl_rxq - Rx queue
* @bd: driver's pointer to buffer of receive buffer descriptors (rbd)
* @bd_dma: bus address of buffer of receive buffer descriptors (rbd)
+ * @pool:
+ * @queue:
* @read: Shared index to newest available Rx buffer
* @write: Shared index to oldest written Rx packet
* @free_count: Number of pre-allocated buffers in rx_free
- * @used_count: Number of RBDs handled to allocator to use for allocation
* @write_actual:
- * @rx_free: list of RBDs with allocated RB ready for use
- * @rx_used: list of RBDs with no RB attached
+ * @rx_free: list of free SKBs for use
+ * @rx_used: List of Rx buffers with no SKB
* @need_update: flag to indicate we need to update read/write index
* @rb_stts: driver's pointer to receive buffer status
* @rb_stts_dma: bus address of receive buffer status
* @lock:
- * @pool: initial pool of iwl_rx_mem_buffer for the queue
- * @queue: actual rx queue
*
* NOTE: rx_free and rx_used are used as a FIFO for iwl_rx_mem_buffers
*/
struct iwl_rxq {
__le32 *bd;
dma_addr_t bd_dma;
+ struct iwl_rx_mem_buffer pool[RX_QUEUE_SIZE + RX_FREE_BUFFERS];
+ struct iwl_rx_mem_buffer *queue[RX_QUEUE_SIZE];
u32 read;
u32 write;
u32 free_count;
- u32 used_count;
u32 write_actual;
struct list_head rx_free;
struct list_head rx_used;
@@ -116,32 +107,6 @@ struct iwl_rxq {
struct iwl_rb_status *rb_stts;
dma_addr_t rb_stts_dma;
spinlock_t lock;
- struct iwl_rx_mem_buffer pool[RX_QUEUE_SIZE];
- struct iwl_rx_mem_buffer *queue[RX_QUEUE_SIZE];
-};
-
-/**
- * struct iwl_rb_allocator - Rx allocator
- * @pool: initial pool of allocator
- * @req_pending: number of requests the allcator had not processed yet
- * @req_ready: number of requests honored and ready for claiming
- * @rbd_allocated: RBDs with pages allocated and ready to be handled to
- * the queue. This is a list of &struct iwl_rx_mem_buffer
- * @rbd_empty: RBDs with no page attached for allocator use. This is a list
- * of &struct iwl_rx_mem_buffer
- * @lock: protects the rbd_allocated and rbd_empty lists
- * @alloc_wq: work queue for background calls
- * @rx_alloc: work struct for background calls
- */
-struct iwl_rb_allocator {
- struct iwl_rx_mem_buffer pool[RX_POOL_SIZE];
- atomic_t req_pending;
- atomic_t req_ready;
- struct list_head rbd_allocated;
- struct list_head rbd_empty;
- spinlock_t lock;
- struct workqueue_struct *alloc_wq;
- struct work_struct rx_alloc;
};
struct iwl_dma_ptr {
@@ -285,7 +250,7 @@ iwl_pcie_get_scratchbuf_dma(struct iwl_txq *txq, int idx)
/**
* struct iwl_trans_pcie - PCIe transport specific data
* @rxq: all the RX queue data
- * @rba: allocator for RX replenishing
+ * @rx_replenish: work that will be called when buffers need to be allocated
* @drv - pointer to iwl_drv
* @trans: pointer to the generic transport area
* @scd_base_addr: scheduler sram base address in SRAM
@@ -308,7 +273,7 @@ iwl_pcie_get_scratchbuf_dma(struct iwl_txq *txq, int idx)
*/
struct iwl_trans_pcie {
struct iwl_rxq rxq;
- struct iwl_rb_allocator rba;
+ struct work_struct rx_replenish;
struct iwl_trans *trans;
struct iwl_drv *drv;
diff --git a/drivers/net/wireless/iwlwifi/pcie/rx.c b/drivers/net/wireless/iwlwifi/pcie/rx.c
index a3fbaa0..adad8d0 100644
--- a/drivers/net/wireless/iwlwifi/pcie/rx.c
+++ b/drivers/net/wireless/iwlwifi/pcie/rx.c
@@ -1,7 +1,7 @@
/******************************************************************************
*
* Copyright(c) 2003 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
*
* Portions of this file are derived from the ipw3945 project, as well
* as portions of the ieee80211 subsystem header files.
@@ -74,29 +74,16 @@
* resets the Rx queue buffers with new memory.
*
* The management in the driver is as follows:
- * + A list of pre-allocated RBDs is stored in iwl->rxq->rx_free.
- * When the interrupt handler is called, the request is processed.
- * The page is either stolen - transferred to the upper layer
- * or reused - added immediately to the iwl->rxq->rx_free list.
- * + When the page is stolen - the driver updates the matching queue's used
- * count, detaches the RBD and transfers it to the queue used list.
- * When there are two used RBDs - they are transferred to the allocator empty
- * list. Work is then scheduled for the allocator to start allocating
- * eight buffers.
- * When there are another 6 used RBDs - they are transferred to the allocator
- * empty list and the driver tries to claim the pre-allocated buffers and
- * add them to iwl->rxq->rx_free. If it fails - it continues to claim them
- * until ready.
- * When there are 8+ buffers in the free list - either from allocation or from
- * 8 reused unstolen pages - restock is called to update the FW and indexes.
- * + In order to make sure the allocator always has RBDs to use for allocation
- * the allocator has initial pool in the size of num_queues*(8-2) - the
- * maximum missing RBDs per allocation request (request posted with 2
- * empty RBDs, there is no guarantee when the other 6 RBDs are supplied).
- * The queues supplies the recycle of the rest of the RBDs.
+ * + A list of pre-allocated SKBs is stored in iwl->rxq->rx_free. When
+ * iwl->rxq->free_count drops to or below RX_LOW_WATERMARK, work is scheduled
+ * to replenish the iwl->rxq->rx_free.
+ * + In iwl_pcie_rx_replenish (scheduled) if 'processed' != 'read' then the
+ * iwl->rxq is replenished and the READ INDEX is updated (updating the
+ * 'processed' and 'read' driver indexes as well)
* + A received packet is processed and handed to the kernel network stack,
* detached from the iwl->rxq. The driver 'processed' index is updated.
- * + If there are no allocated buffers in iwl->rxq->rx_free,
+ * + The Host/Firmware iwl->rxq is replenished at irq thread time from the
+ * rx_free list. If there are no allocated buffers in iwl->rxq->rx_free,
* the READ INDEX is not incremented and iwl->status(RX_STALLED) is set.
* If there were enough free buffers and RX_STALLED is set it is cleared.
*
@@ -105,32 +92,18 @@
*
* iwl_rxq_alloc() Allocates rx_free
* iwl_pcie_rx_replenish() Replenishes rx_free list from rx_used, and calls
- * iwl_pcie_rxq_restock.
- * Used only during initialization.
+ * iwl_pcie_rxq_restock
* iwl_pcie_rxq_restock() Moves available buffers from rx_free into Rx
* queue, updates firmware pointers, and updates
- * the WRITE index.
- * iwl_pcie_rx_allocator() Background work for allocating pages.
+ * the WRITE index. If insufficient rx_free buffers
+ * are available, schedules iwl_pcie_rx_replenish
*
* -- enable interrupts --
* ISR - iwl_rx() Detach iwl_rx_mem_buffers from pool up to the
* READ INDEX, detaching the SKB from the pool.
* Moves the packet buffer from queue to rx_used.
- * Posts and claims requests to the allocator.
* Calls iwl_pcie_rxq_restock to refill any empty
* slots.
- *
- * RBD life-cycle:
- *
- * Init:
- * rxq.pool -> rxq.rx_used -> rxq.rx_free -> rxq.queue
- *
- * Regular Receive interrupt:
- * Page Stolen:
- * rxq.queue -> rxq.rx_used -> allocator.rbd_empty ->
- * allocator.rbd_allocated -> rxq.rx_free -> rxq.queue
- * Page not Stolen:
- * rxq.queue -> rxq.rx_free -> rxq.queue
* ...
*
*/
@@ -267,6 +240,10 @@ static void iwl_pcie_rxq_restock(struct iwl_trans *trans)
rxq->free_count--;
}
spin_unlock(&rxq->lock);
+ /* If the pre-allocated buffer pool is dropping low, schedule to
+ * refill it */
+ if (rxq->free_count <= RX_LOW_WATERMARK)
+ schedule_work(&trans_pcie->rx_replenish);
/* If we've added more space for the firmware to place data, tell it.
* Increment device's write pointer in multiples of 8. */
@@ -278,44 +255,6 @@ static void iwl_pcie_rxq_restock(struct iwl_trans *trans)
}
/*
- * iwl_pcie_rx_alloc_page - allocates and returns a page.
- *
- */
-static struct page *iwl_pcie_rx_alloc_page(struct iwl_trans *trans)
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct iwl_rxq *rxq = &trans_pcie->rxq;
- struct page *page;
- gfp_t gfp_mask = GFP_KERNEL;
-
- if (rxq->free_count > RX_LOW_WATERMARK)
- gfp_mask |= __GFP_NOWARN;
-
- if (trans_pcie->rx_page_order > 0)
- gfp_mask |= __GFP_COMP;
-
- /* Alloc a new receive buffer */
- page = alloc_pages(gfp_mask, trans_pcie->rx_page_order);
- if (!page) {
- if (net_ratelimit())
- IWL_DEBUG_INFO(trans, "alloc_pages failed, order: %d\n",
- trans_pcie->rx_page_order);
- /* Issue an error if the hardware has consumed more than half
- * of its free buffer list and we don't have enough
- * pre-allocated buffers.
-` */
- if (rxq->free_count <= RX_LOW_WATERMARK &&
- iwl_rxq_space(rxq) > (RX_QUEUE_SIZE / 2) &&
- net_ratelimit())
- IWL_CRIT(trans,
- "Failed to alloc_pages with GFP_KERNEL. Only %u free buffers remaining.\n",
- rxq->free_count);
- return NULL;
- }
- return page;
-}
-
-/*
* iwl_pcie_rxq_alloc_rbs - allocate a page for each used RBD
*
* A used RBD is an Rx buffer that has been given to the stack. To use it again
@@ -324,12 +263,13 @@ static struct page *iwl_pcie_rx_alloc_page(struct iwl_trans *trans)
* iwl_pcie_rxq_restock. The latter function will update the HW to use the newly
* allocated buffers.
*/
-static void iwl_pcie_rxq_alloc_rbs(struct iwl_trans *trans)
+static void iwl_pcie_rxq_alloc_rbs(struct iwl_trans *trans, gfp_t priority)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
struct iwl_rxq *rxq = &trans_pcie->rxq;
struct iwl_rx_mem_buffer *rxb;
struct page *page;
+ gfp_t gfp_mask = priority;
while (1) {
spin_lock(&rxq->lock);
@@ -339,10 +279,32 @@ static void iwl_pcie_rxq_alloc_rbs(struct iwl_trans *trans)
}
spin_unlock(&rxq->lock);
+ if (rxq->free_count > RX_LOW_WATERMARK)
+ gfp_mask |= __GFP_NOWARN;
+
+ if (trans_pcie->rx_page_order > 0)
+ gfp_mask |= __GFP_COMP;
+
/* Alloc a new receive buffer */
- page = iwl_pcie_rx_alloc_page(trans);
- if (!page)
+ page = alloc_pages(gfp_mask, trans_pcie->rx_page_order);
+ if (!page) {
+ if (net_ratelimit())
+ IWL_DEBUG_INFO(trans, "alloc_pages failed, "
+ "order: %d\n",
+ trans_pcie->rx_page_order);
+
+ if ((rxq->free_count <= RX_LOW_WATERMARK) &&
+ net_ratelimit())
+ IWL_CRIT(trans, "Failed to alloc_pages with %s."
+ "Only %u free buffers remaining.\n",
+ priority == GFP_ATOMIC ?
+ "GFP_ATOMIC" : "GFP_KERNEL",
+ rxq->free_count);
+ /* We don't reschedule replenish work here -- we will
+ * call the restock method and if it still needs
+ * more buffers it will schedule replenish */
return;
+ }
spin_lock(&rxq->lock);
@@ -393,7 +355,7 @@ static void iwl_pcie_rxq_free_rbs(struct iwl_trans *trans)
lockdep_assert_held(&rxq->lock);
- for (i = 0; i < RX_QUEUE_SIZE; i++) {
+ for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++) {
if (!rxq->pool[i].page)
continue;
dma_unmap_page(trans->dev, rxq->pool[i].page_dma,
@@ -410,144 +372,32 @@ static void iwl_pcie_rxq_free_rbs(struct iwl_trans *trans)
* When moving to rx_free an page is allocated for the slot.
*
* Also restock the Rx queue via iwl_pcie_rxq_restock.
- * This is called only during initialization
+ * This is called as a scheduled work item (except for during initialization)
*/
-static void iwl_pcie_rx_replenish(struct iwl_trans *trans)
+static void iwl_pcie_rx_replenish(struct iwl_trans *trans, gfp_t gfp)
{
- iwl_pcie_rxq_alloc_rbs(trans);
+ iwl_pcie_rxq_alloc_rbs(trans, gfp);
iwl_pcie_rxq_restock(trans);
}
-/*
- * iwl_pcie_rx_allocator - Allocates pages in the background for RX queues
- *
- * Allocates for each received request 8 pages
- * Called as a scheduled work item.
- */
-static void iwl_pcie_rx_allocator(struct iwl_trans *trans)
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
-
- while (atomic_read(&rba->req_pending)) {
- int i;
- struct list_head local_empty;
- struct list_head local_allocated;
-
- INIT_LIST_HEAD(&local_allocated);
- spin_lock(&rba->lock);
- /* swap out the entire rba->rbd_empty to a local list */
- list_replace_init(&rba->rbd_empty, &local_empty);
- spin_unlock(&rba->lock);
-
- for (i = 0; i < RX_CLAIM_REQ_ALLOC;) {
- struct iwl_rx_mem_buffer *rxb;
- struct page *page;
-
- /* List should never be empty - each reused RBD is
- * returned to the list, and initial pool covers any
- * possible gap between the time the page is allocated
- * to the time the RBD is added.
- */
- BUG_ON(list_empty(&local_empty));
- /* Get the first rxb from the rbd list */
- rxb = list_first_entry(&local_empty,
- struct iwl_rx_mem_buffer, list);
- BUG_ON(rxb->page);
-
- /* Alloc a new receive buffer */
- page = iwl_pcie_rx_alloc_page(trans);
- if (!page)
- continue;
- rxb->page = page;
-
- /* Get physical address of the RB */
- rxb->page_dma = dma_map_page(trans->dev, page, 0,
- PAGE_SIZE << trans_pcie->rx_page_order,
- DMA_FROM_DEVICE);
- if (dma_mapping_error(trans->dev, rxb->page_dma)) {
- rxb->page = NULL;
- __free_pages(page, trans_pcie->rx_page_order);
- continue;
- }
- /* dma address must be no more than 36 bits */
- BUG_ON(rxb->page_dma & ~DMA_BIT_MASK(36));
- /* and also 256 byte aligned! */
- BUG_ON(rxb->page_dma & DMA_BIT_MASK(8));
-
- /* move the allocated entry to the out list */
- list_move(&rxb->list, &local_allocated);
- i++;
- }
-
- spin_lock(&rba->lock);
- /* add the allocated rbds to the allocator allocated list */
- list_splice_tail(&local_allocated, &rba->rbd_allocated);
- /* add the unused rbds back to the allocator empty list */
- list_splice_tail(&local_empty, &rba->rbd_empty);
- spin_unlock(&rba->lock);
-
- atomic_dec(&rba->req_pending);
- atomic_inc(&rba->req_ready);
- }
-}
-
-/*
- * iwl_pcie_rx_allocator_get - Returns the pre-allocated pages
-.*
-.* Called by queue when the queue posted allocation request and
- * has freed 8 RBDs in order to restock itself.
- */
-static int iwl_pcie_rx_allocator_get(struct iwl_trans *trans,
- struct iwl_rx_mem_buffer
- *out[RX_CLAIM_REQ_ALLOC])
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
- int i;
-
- if (atomic_dec_return(&rba->req_ready) < 0) {
- atomic_inc(&rba->req_ready);
- IWL_DEBUG_RX(trans,
- "Allocation request not ready, pending requests = %d\n",
- atomic_read(&rba->req_pending));
- return -ENOMEM;
- }
-
- spin_lock(&rba->lock);
- for (i = 0; i < RX_CLAIM_REQ_ALLOC; i++) {
- /* Get next free Rx buffer, remove it from free list */
- out[i] = list_first_entry(&rba->rbd_allocated,
- struct iwl_rx_mem_buffer, list);
- list_del(&out[i]->list);
- }
- spin_unlock(&rba->lock);
-
- return 0;
-}
-
-static void iwl_pcie_rx_allocator_work(struct work_struct *data)
+static void iwl_pcie_rx_replenish_work(struct work_struct *data)
{
- struct iwl_rb_allocator *rba_p =
- container_of(data, struct iwl_rb_allocator, rx_alloc);
struct iwl_trans_pcie *trans_pcie =
- container_of(rba_p, struct iwl_trans_pcie, rba);
+ container_of(data, struct iwl_trans_pcie, rx_replenish);
- iwl_pcie_rx_allocator(trans_pcie->trans);
+ iwl_pcie_rx_replenish(trans_pcie->trans, GFP_KERNEL);
}
static int iwl_pcie_rx_alloc(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
struct iwl_rxq *rxq = &trans_pcie->rxq;
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
struct device *dev = trans->dev;
memset(&trans_pcie->rxq, 0, sizeof(trans_pcie->rxq));
spin_lock_init(&rxq->lock);
- spin_lock_init(&rba->lock);
if (WARN_ON(rxq->bd || rxq->rb_stts))
return -EINVAL;
@@ -637,49 +487,15 @@ static void iwl_pcie_rx_init_rxb_lists(struct iwl_rxq *rxq)
INIT_LIST_HEAD(&rxq->rx_free);
INIT_LIST_HEAD(&rxq->rx_used);
rxq->free_count = 0;
- rxq->used_count = 0;
- for (i = 0; i < RX_QUEUE_SIZE; i++)
+ for (i = 0; i < RX_FREE_BUFFERS + RX_QUEUE_SIZE; i++)
list_add(&rxq->pool[i].list, &rxq->rx_used);
}
-static void iwl_pcie_rx_init_rba(struct iwl_rb_allocator *rba)
-{
- int i;
-
- lockdep_assert_held(&rba->lock);
-
- INIT_LIST_HEAD(&rba->rbd_allocated);
- INIT_LIST_HEAD(&rba->rbd_empty);
-
- for (i = 0; i < RX_POOL_SIZE; i++)
- list_add(&rba->pool[i].list, &rba->rbd_empty);
-}
-
-static void iwl_pcie_rx_free_rba(struct iwl_trans *trans)
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
- int i;
-
- lockdep_assert_held(&rba->lock);
-
- for (i = 0; i < RX_POOL_SIZE; i++) {
- if (!rba->pool[i].page)
- continue;
- dma_unmap_page(trans->dev, rba->pool[i].page_dma,
- PAGE_SIZE << trans_pcie->rx_page_order,
- DMA_FROM_DEVICE);
- __free_pages(rba->pool[i].page, trans_pcie->rx_page_order);
- rba->pool[i].page = NULL;
- }
-}
-
int iwl_pcie_rx_init(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
struct iwl_rxq *rxq = &trans_pcie->rxq;
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
int i, err;
if (!rxq->bd) {
@@ -687,21 +503,11 @@ int iwl_pcie_rx_init(struct iwl_trans *trans)
if (err)
return err;
}
- if (!rba->alloc_wq)
- rba->alloc_wq = alloc_workqueue("rb_allocator",
- WQ_HIGHPRI | WQ_UNBOUND, 1);
- INIT_WORK(&rba->rx_alloc, iwl_pcie_rx_allocator_work);
-
- spin_lock(&rba->lock);
- atomic_set(&rba->req_pending, 0);
- atomic_set(&rba->req_ready, 0);
- /* free all first - we might be reconfigured for a different size */
- iwl_pcie_rx_free_rba(trans);
- iwl_pcie_rx_init_rba(rba);
- spin_unlock(&rba->lock);
spin_lock(&rxq->lock);
+ INIT_WORK(&trans_pcie->rx_replenish, iwl_pcie_rx_replenish_work);
+
/* free all first - we might be reconfigured for a different size */
iwl_pcie_rxq_free_rbs(trans);
iwl_pcie_rx_init_rxb_lists(rxq);
@@ -716,7 +522,7 @@ int iwl_pcie_rx_init(struct iwl_trans *trans)
memset(rxq->rb_stts, 0, sizeof(*rxq->rb_stts));
spin_unlock(&rxq->lock);
- iwl_pcie_rx_replenish(trans);
+ iwl_pcie_rx_replenish(trans, GFP_KERNEL);
iwl_pcie_rx_hw_init(trans, rxq);
@@ -731,7 +537,6 @@ void iwl_pcie_rx_free(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
struct iwl_rxq *rxq = &trans_pcie->rxq;
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
/*if rxq->bd is NULL, it means that nothing has been allocated,
* exit now */
@@ -740,15 +545,7 @@ void iwl_pcie_rx_free(struct iwl_trans *trans)
return;
}
- cancel_work_sync(&rba->rx_alloc);
- if (rba->alloc_wq) {
- destroy_workqueue(rba->alloc_wq);
- rba->alloc_wq = NULL;
- }
-
- spin_lock(&rba->lock);
- iwl_pcie_rx_free_rba(trans);
- spin_unlock(&rba->lock);
+ cancel_work_sync(&trans_pcie->rx_replenish);
spin_lock(&rxq->lock);
iwl_pcie_rxq_free_rbs(trans);
@@ -769,43 +566,6 @@ void iwl_pcie_rx_free(struct iwl_trans *trans)
rxq->rb_stts = NULL;
}
-/*
- * iwl_pcie_rx_reuse_rbd - Recycle used RBDs
- *
- * Called when a RBD can be reused. The RBD is transferred to the allocator.
- * When there are 2 empty RBDs - a request for allocation is posted
- */
-static void iwl_pcie_rx_reuse_rbd(struct iwl_trans *trans,
- struct iwl_rx_mem_buffer *rxb,
- struct iwl_rxq *rxq)
-{
- struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
-
- /* Count the used RBDs */
- rxq->used_count++;
-
- /* Move the RBD to the used list, will be moved to allocator in batches
- * before claiming or posting a request*/
- list_add_tail(&rxb->list, &rxq->rx_used);
-
- /* If we have RX_POST_REQ_ALLOC new released rx buffers -
- * issue a request for allocator. Modulo RX_CLAIM_REQ_ALLOC is
- * used for the case we failed to claim RX_CLAIM_REQ_ALLOC,
- * after but we still need to post another request.
- */
- if ((rxq->used_count % RX_CLAIM_REQ_ALLOC) == RX_POST_REQ_ALLOC) {
- /* Move the 2 RBDs to the allocator ownership.
- Allocator has another 6 from pool for the request completion*/
- spin_lock(&rba->lock);
- list_splice_tail_init(&rxq->rx_used, &rba->rbd_empty);
- spin_unlock(&rba->lock);
-
- atomic_inc(&rba->req_pending);
- queue_work(rba->alloc_wq, &rba->rx_alloc);
- }
-}
-
static void iwl_pcie_rx_handle_rb(struct iwl_trans *trans,
struct iwl_rx_mem_buffer *rxb)
{
@@ -928,13 +688,13 @@ static void iwl_pcie_rx_handle_rb(struct iwl_trans *trans,
*/
__free_pages(rxb->page, trans_pcie->rx_page_order);
rxb->page = NULL;
- iwl_pcie_rx_reuse_rbd(trans, rxb, rxq);
+ list_add_tail(&rxb->list, &rxq->rx_used);
} else {
list_add_tail(&rxb->list, &rxq->rx_free);
rxq->free_count++;
}
} else
- iwl_pcie_rx_reuse_rbd(trans, rxb, rxq);
+ list_add_tail(&rxb->list, &rxq->rx_used);
}
/*
@@ -944,7 +704,10 @@ static void iwl_pcie_rx_handle(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
struct iwl_rxq *rxq = &trans_pcie->rxq;
- u32 r, i, j;
+ u32 r, i;
+ u8 fill_rx = 0;
+ u32 count = 8;
+ int total_empty;
restart:
spin_lock(&rxq->lock);
@@ -957,6 +720,14 @@ restart:
if (i == r)
IWL_DEBUG_RX(trans, "HW = SW = %d\n", r);
+ /* calculate total frames need to be restock after handling RX */
+ total_empty = r - rxq->write_actual;
+ if (total_empty < 0)
+ total_empty += RX_QUEUE_SIZE;
+
+ if (total_empty > (RX_QUEUE_SIZE / 2))
+ fill_rx = 1;
+
while (i != r) {
struct iwl_rx_mem_buffer *rxb;
@@ -968,48 +739,29 @@ restart:
iwl_pcie_rx_handle_rb(trans, rxb);
i = (i + 1) & RX_QUEUE_MASK;
-
- /* If we have RX_CLAIM_REQ_ALLOC released rx buffers -
- * try to claim the pre-allocated buffers from the allocator */
- if (rxq->used_count >= RX_CLAIM_REQ_ALLOC) {
- struct iwl_rb_allocator *rba = &trans_pcie->rba;
- struct iwl_rx_mem_buffer *out[RX_CLAIM_REQ_ALLOC];
-
- /* Add the remaining 6 empty RBDs for allocator use */
- spin_lock(&rba->lock);
- list_splice_tail_init(&rxq->rx_used, &rba->rbd_empty);
- spin_unlock(&rba->lock);
-
- /* If not ready - continue, will try to reclaim later.
- * No need to reschedule work - allocator exits only on
- * success */
- if (!iwl_pcie_rx_allocator_get(trans, out)) {
- /* If success - then RX_CLAIM_REQ_ALLOC
- * buffers were retrieved and should be added
- * to free list */
- rxq->used_count -= RX_CLAIM_REQ_ALLOC;
- for (j = 0; j < RX_CLAIM_REQ_ALLOC; j++) {
- list_add_tail(&out[j]->list,
- &rxq->rx_free);
- rxq->free_count++;
- }
+ /* If there are a lot of unused frames,
+ * restock the Rx queue so ucode wont assert. */
+ if (fill_rx) {
+ count++;
+ if (count >= 8) {
+ rxq->read = i;
+ spin_unlock(&rxq->lock);
+ iwl_pcie_rx_replenish(trans, GFP_ATOMIC);
+ count = 0;
+ goto restart;
}
}
- /* handle restock for two cases:
- * - we just pulled buffers from the allocator
- * - we have 8+ unstolen pages accumulated */
- if (rxq->free_count >= RX_CLAIM_REQ_ALLOC) {
- rxq->read = i;
- spin_unlock(&rxq->lock);
- iwl_pcie_rxq_restock(trans);
- goto restart;
- }
}
/* Backtrack one entry */
rxq->read = i;
spin_unlock(&rxq->lock);
+ if (fill_rx)
+ iwl_pcie_rx_replenish(trans, GFP_ATOMIC);
+ else
+ iwl_pcie_rxq_restock(trans);
+
if (trans_pcie->napi.poll)
napi_gro_flush(&trans_pcie->napi, false);
}
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 10/10] iwlwifi: nvm: remove mac address byte swapping in 8000 family
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (8 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 09/10] Revert "iwlwifi: pcie: New RBD allocation model" Emmanuel Grumbach
@ 2015-07-12 17:08 ` Emmanuel Grumbach
2015-07-17 8:26 ` pull request: iwlwifi 2015-06-15 Kalle Valo
10 siblings, 0 replies; 13+ messages in thread
From: Emmanuel Grumbach @ 2015-07-12 17:08 UTC (permalink / raw)
To: linux-wireless; +Cc: Liad Kaufman, stable, Emmanuel Grumbach
From: Liad Kaufman <liad.kaufman@intel.com>
This fixes the byte order copying in the MAO (Mac Override
Section) section from the PNVM, as the byte swapping is not
required anymore in the 8000 family. Due to the byte
swapping, the driver was reporting an incorrect MAC
adddress.
CC: <stable@vger.kernel.org> [4.1]
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
---
drivers/net/wireless/iwlwifi/iwl-nvm-parse.c | 12 +++++-------
1 file changed, 5 insertions(+), 7 deletions(-)
diff --git a/drivers/net/wireless/iwlwifi/iwl-nvm-parse.c b/drivers/net/wireless/iwlwifi/iwl-nvm-parse.c
index 80fefe7..3b8e85e 100644
--- a/drivers/net/wireless/iwlwifi/iwl-nvm-parse.c
+++ b/drivers/net/wireless/iwlwifi/iwl-nvm-parse.c
@@ -540,13 +540,11 @@ static void iwl_set_hw_address_family_8000(struct device *dev,
hw_addr = (const u8 *)(mac_override +
MAC_ADDRESS_OVERRIDE_FAMILY_8000);
- /* The byte order is little endian 16 bit, meaning 214365 */
- data->hw_addr[0] = hw_addr[1];
- data->hw_addr[1] = hw_addr[0];
- data->hw_addr[2] = hw_addr[3];
- data->hw_addr[3] = hw_addr[2];
- data->hw_addr[4] = hw_addr[5];
- data->hw_addr[5] = hw_addr[4];
+ /*
+ * Store the MAC address from MAO section.
+ * No byte swapping is required in MAO section
+ */
+ memcpy(data->hw_addr, hw_addr, ETH_ALEN);
/*
* Force the use of the OTP MAC address in case of reserved MAC
--
2.1.4
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: pull request: iwlwifi 2015-06-15
2015-07-12 17:06 pull request: iwlwifi 2015-06-15 Grumbach, Emmanuel
` (9 preceding siblings ...)
2015-07-12 17:08 ` [PATCH 10/10] iwlwifi: nvm: remove mac address byte swapping in 8000 family Emmanuel Grumbach
@ 2015-07-17 8:26 ` Kalle Valo
10 siblings, 0 replies; 13+ messages in thread
From: Kalle Valo @ 2015-07-17 8:26 UTC (permalink / raw)
To: Grumbach, Emmanuel; +Cc: linux-wireless
"Grumbach, Emmanuel" <emmanuel.grumbach@intel.com> writes:
> This is the first pull request of fixes for 4.2. A few of the patches
> here are CCed to stable. Besides fix for (hard to hit) crashes there are
> a bunch of fixes for 8000 devices which are now undergoing the final
> round of tests.
> Let me know if you have issues!
>
> emmanuel
>
>
> The following changes since commit e0456717e483bb8a9431b80a5bdc99a928b9b003:
>
> Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next (2015-06-24 16:49:49 -0700)
>
> are available in the git repository at:
>
> https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes.git tags/iwlwifi-for-kalle-2015-06-12
>
Thanks, pulled.
--
Kalle Valo
^ permalink raw reply [flat|nested] 13+ messages in thread