From: Glen Lee <glen.lee@atmel.com>
To: <gregkh@linuxfoundation.org>
Cc: <devel@driverdev.osuosl.org>, <linux-wireless@vger.kernel.org>,
<tony.cho@atmel.com>, <glen.lee@atmel.com>, <leo.kim@atmel.com>,
<austin.shin@atmel.com>, <adel.noureldin@atmel.com>,
<adham.abozaeid@atmel.com>, <Nicolas.FERRE@atmel.com>
Subject: [PATCH 03/10] staging: wilc1000: remove unused functions
Date: Mon, 23 Nov 2015 18:48:01 +0900 [thread overview]
Message-ID: <1448272088-13973-3-git-send-email-glen.lee@atmel.com> (raw)
In-Reply-To: <1448272088-13973-1-git-send-email-glen.lee@atmel.com>
This patch removes unused function pointer hif_sync and hif_clear_int, and
removes it's related functions sdio_clear_int, sdio_sync, wilc_spi_clear_int
and wilc_spi_sync.
Signed-off-by: Glen Lee <glen.lee@atmel.com>
---
drivers/staging/wilc1000/wilc_sdio.c | 94 ------------------------------------
drivers/staging/wilc1000/wilc_spi.c | 60 -----------------------
drivers/staging/wilc1000/wilc_wlan.h | 2 -
3 files changed, 156 deletions(-)
diff --git a/drivers/staging/wilc1000/wilc_sdio.c b/drivers/staging/wilc1000/wilc_sdio.c
index c2c10dd..1381a10 100644
--- a/drivers/staging/wilc1000/wilc_sdio.c
+++ b/drivers/staging/wilc1000/wilc_sdio.c
@@ -130,37 +130,6 @@ _fail_:
return 0;
}
-static int sdio_clear_int(struct wilc *wilc)
-{
- struct sdio_func *func = dev_to_sdio_func(wilc->dev);
-
- if (!g_sdio.irq_gpio) {
- /* u32 sts; */
- sdio_cmd52_t cmd;
-
- cmd.read_write = 0;
- cmd.function = 1;
- cmd.raw = 0;
- cmd.address = 0x4;
- cmd.data = 0;
- wilc_sdio_cmd52(wilc, &cmd);
-
- return cmd.data;
- } else {
- u32 reg;
-
- if (!sdio_read_reg(wilc, WILC_HOST_RX_CTRL_0, ®)) {
- dev_err(&func->dev, "Failed read reg (%08x)...\n",
- WILC_HOST_RX_CTRL_0);
- return 0;
- }
- reg &= ~0x1;
- sdio_write_reg(wilc, WILC_HOST_RX_CTRL_0, reg);
- return 1;
- }
-
-}
-
/********************************************
*
* Sdio interfaces
@@ -451,67 +420,6 @@ static int sdio_deinit(struct wilc *wilc)
return 1;
}
-static int sdio_sync(struct wilc *wilc)
-{
- struct sdio_func *func = dev_to_sdio_func(wilc->dev);
- u32 reg;
-
- /**
- * Disable power sequencer
- **/
- if (!sdio_read_reg(wilc, WILC_MISC, ®)) {
- dev_err(&func->dev, "Failed read misc reg...\n");
- return 0;
- }
-
- reg &= ~BIT(8);
- if (!sdio_write_reg(wilc, WILC_MISC, reg)) {
- dev_err(&func->dev, "Failed write misc reg...\n");
- return 0;
- }
-
- if (g_sdio.irq_gpio) {
- u32 reg;
- int ret;
-
- /**
- * interrupt pin mux select
- **/
- ret = sdio_read_reg(wilc, WILC_PIN_MUX_0, ®);
- if (!ret) {
- dev_err(&func->dev, "Failed read reg (%08x)...\n",
- WILC_PIN_MUX_0);
- return 0;
- }
- reg |= BIT(8);
- ret = sdio_write_reg(wilc, WILC_PIN_MUX_0, reg);
- if (!ret) {
- dev_err(&func->dev, "Failed write reg (%08x)...\n",
- WILC_PIN_MUX_0);
- return 0;
- }
-
- /**
- * interrupt enable
- **/
- ret = sdio_read_reg(wilc, WILC_INTR_ENABLE, ®);
- if (!ret) {
- dev_err(&func->dev, "Failed read reg (%08x)...\n",
- WILC_INTR_ENABLE);
- return 0;
- }
- reg |= BIT(16);
- ret = sdio_write_reg(wilc, WILC_INTR_ENABLE, reg);
- if (!ret) {
- dev_err(&func->dev, "Failed write reg (%08x)...\n",
- WILC_INTR_ENABLE);
- return 0;
- }
- }
-
- return 1;
-}
-
static int sdio_init(struct wilc *wilc)
{
struct sdio_func *func = dev_to_sdio_func(wilc->dev);
@@ -950,8 +858,6 @@ const struct wilc_hif_func wilc_hif_sdio = {
.hif_write_reg = sdio_write_reg,
.hif_block_rx = sdio_read,
.hif_block_tx = sdio_write,
- .hif_sync = sdio_sync,
- .hif_clear_int = sdio_clear_int,
.hif_read_int = sdio_read_int,
.hif_clear_int_ext = sdio_clear_int_ext,
.hif_read_size = sdio_read_size,
diff --git a/drivers/staging/wilc1000/wilc_spi.c b/drivers/staging/wilc1000/wilc_spi.c
index 6032a8f..f54072b 100644
--- a/drivers/staging/wilc1000/wilc_spi.c
+++ b/drivers/staging/wilc1000/wilc_spi.c
@@ -668,21 +668,6 @@ static int _wilc_spi_read(struct wilc *wilc, u32 addr, u8 *buf, u32 size)
*
********************************************/
-static int wilc_spi_clear_int(struct wilc *wilc)
-{
- struct spi_device *spi = to_spi_device(wilc->dev);
- u32 reg;
-
- if (!wilc_spi_read_reg(wilc, WILC_HOST_RX_CTRL_0, ®)) {
- dev_err(&spi->dev, "Failed read reg (%08x)...\n",
- WILC_HOST_RX_CTRL_0);
- return 0;
- }
- reg &= ~0x1;
- wilc_spi_write_reg(wilc, WILC_HOST_RX_CTRL_0, reg);
- return 1;
-}
-
static int _wilc_spi_deinit(struct wilc *wilc)
{
/**
@@ -691,49 +676,6 @@ static int _wilc_spi_deinit(struct wilc *wilc)
return 1;
}
-static int wilc_spi_sync(struct wilc *wilc)
-{
- struct spi_device *spi = to_spi_device(wilc->dev);
- u32 reg;
- int ret;
-
- /**
- * interrupt pin mux select
- **/
- ret = wilc_spi_read_reg(wilc, WILC_PIN_MUX_0, ®);
- if (!ret) {
- dev_err(&spi->dev,"Failed read reg (%08x)...\n",
- WILC_PIN_MUX_0);
- return 0;
- }
- reg |= BIT(8);
- ret = wilc_spi_write_reg(wilc, WILC_PIN_MUX_0, reg);
- if (!ret) {
- dev_err(&spi->dev, "Failed write reg (%08x)...\n",
- WILC_PIN_MUX_0);
- return 0;
- }
-
- /**
- * interrupt enable
- **/
- ret = wilc_spi_read_reg(wilc, WILC_INTR_ENABLE, ®);
- if (!ret) {
- dev_err(&spi->dev, "Failed read reg (%08x)...\n",
- WILC_INTR_ENABLE);
- return 0;
- }
- reg |= BIT(16);
- ret = wilc_spi_write_reg(wilc, WILC_INTR_ENABLE, reg);
- if (!ret) {
- dev_err(&spi->dev, "Failed write reg (%08x)...\n",
- WILC_INTR_ENABLE);
- return 0;
- }
-
- return 1;
-}
-
static int _wilc_spi_init(struct wilc *wilc)
{
struct spi_device *spi = to_spi_device(wilc->dev);
@@ -1056,8 +998,6 @@ const struct wilc_hif_func wilc_hif_spi = {
.hif_write_reg = wilc_spi_write_reg,
.hif_block_rx = _wilc_spi_read,
.hif_block_tx = _wilc_spi_write,
- .hif_sync = wilc_spi_sync,
- .hif_clear_int = wilc_spi_clear_int,
.hif_read_int = wilc_spi_read_int,
.hif_clear_int_ext = wilc_spi_clear_int_ext,
.hif_read_size = wilc_spi_read_size,
diff --git a/drivers/staging/wilc1000/wilc_wlan.h b/drivers/staging/wilc1000/wilc_wlan.h
index 580e1d6..2edd744 100644
--- a/drivers/staging/wilc1000/wilc_wlan.h
+++ b/drivers/staging/wilc1000/wilc_wlan.h
@@ -232,8 +232,6 @@ struct wilc_hif_func {
int (*hif_write_reg)(struct wilc *, u32, u32);
int (*hif_block_rx)(struct wilc *, u32, u8 *, u32);
int (*hif_block_tx)(struct wilc *, u32, u8 *, u32);
- int (*hif_sync)(struct wilc *);
- int (*hif_clear_int)(struct wilc *);
int (*hif_read_int)(struct wilc *, u32 *);
int (*hif_clear_int_ext)(struct wilc *, u32);
int (*hif_read_size)(struct wilc *, u32 *);
--
1.9.1
next prev parent reply other threads:[~2015-11-23 9:44 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-23 9:47 [PATCH 01/10] staging: wilc1000: sdio/spi: use device print api instead of custom one Glen Lee
2015-11-23 9:48 ` [PATCH 02/10] staging: wilc1000: remove wilc_debug_func of hif_init Glen Lee
2015-11-23 9:48 ` Glen Lee [this message]
2015-11-23 9:48 ` [PATCH 04/10] staging: wilc1000: linux_wlan_sdio.c: fix checkpatch warning line over 80 Glen Lee
2015-11-23 9:48 ` [PATCH 05/10] staging: wilc1000: linux_wlan_sdio.c: remove braces Glen Lee
2015-11-23 9:48 ` [PATCH 06/10] staging: wilc1000: wilc_sdio_cmd53: return linux error value Glen Lee
2015-11-23 9:48 ` [PATCH 07/10] staging: wilc1000: wilc_sdio_cmd52: " Glen Lee
2015-11-23 9:48 ` [PATCH 08/10] staging: wilc1000: linux_wlan_spi.c: remove braces for single statement Glen Lee
2015-11-23 9:48 ` [PATCH 09/10] staging: wilc1000: linux_wlan_spi.c: add a blank Glen Lee
2015-11-23 9:48 ` [PATCH 10/10] staging: wilc1000: linux_wlan_spi.c: fix NULL comparison style Glen Lee
2015-12-18 22:38 ` [PATCH 01/10] staging: wilc1000: sdio/spi: use device print api instead of custom one Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1448272088-13973-3-git-send-email-glen.lee@atmel.com \
--to=glen.lee@atmel.com \
--cc=Nicolas.FERRE@atmel.com \
--cc=adel.noureldin@atmel.com \
--cc=adham.abozaeid@atmel.com \
--cc=austin.shin@atmel.com \
--cc=devel@driverdev.osuosl.org \
--cc=gregkh@linuxfoundation.org \
--cc=leo.kim@atmel.com \
--cc=linux-wireless@vger.kernel.org \
--cc=tony.cho@atmel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).