From: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
To: <ath11k@lists.infradead.org>
Cc: <linux-wireless@vger.kernel.org>, <devicetree@vger.kernel.org>,
<robh@kernel.org>,
Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Subject: [PATCH v2 06/19] ath11k: Add HW params for WCN6750
Date: Sun, 16 Jan 2022 18:17:02 +0530 [thread overview]
Message-ID: <1642337235-8618-7-git-send-email-quic_mpubbise@quicinc.com> (raw)
In-Reply-To: <1642337235-8618-1-git-send-email-quic_mpubbise@quicinc.com>
Add HW params for WCN6750. It is similar to the HW params
of QCA6390 with few differences wrt DP APIs and register
offsets.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
---
drivers/net/wireless/ath/ath11k/core.c | 58 ++++++++++++++++++++++++++++++++++
drivers/net/wireless/ath/ath11k/core.h | 1 +
drivers/net/wireless/ath/ath11k/qmi.h | 2 ++
3 files changed, 61 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/core.c b/drivers/net/wireless/ath/ath11k/core.c
index 90ac0b5..3acc3e4 100644
--- a/drivers/net/wireless/ath/ath11k/core.c
+++ b/drivers/net/wireless/ath/ath11k/core.c
@@ -408,6 +408,64 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.supports_rssi_stats = true,
.fw_wmi_diag_event = true,
},
+ {
+ .name = "wcn6750 hw1.0",
+ .hw_rev = ATH11K_HW_WCN6750_HW10,
+ .fw = {
+ .dir = "WCN6750/hw1.0",
+ .board_size = 256 * 1024,
+ .cal_offset = 128 * 1024,
+ },
+ .max_radios = 1,
+ .bdf_addr = 0x4B0C0000,
+ .ring_mask = &ath11k_hw_ring_mask_qca6390,
+ .internal_sleep_clock = false,
+ .qmi_service_ins_id = ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_WCN6750,
+ .host_ce_config = ath11k_host_ce_config_qca6390,
+ .ce_count = 9,
+ .target_ce_config = ath11k_target_ce_config_wlan_qca6390,
+ .target_ce_count = 9,
+ .svc_to_ce_map = ath11k_target_service_to_ce_map_wlan_qca6390,
+ .svc_to_ce_map_len = 14,
+ .rfkill_pin = 0,
+ .rfkill_cfg = 0,
+ .rfkill_on_level = 0,
+ .single_pdev_only = true,
+ .rxdma1_enable = false,
+ .num_rxmda_per_pdev = 1,
+ .rx_mac_buf_ring = true,
+ .vdev_start_delay = true,
+ .htt_peer_map_v2 = false,
+
+ .spectral = {
+ .fft_sz = 0,
+ .fft_pad_sz = 0,
+ .summary_pad_sz = 0,
+ .fft_hdr_len = 0,
+ .max_fft_bins = 0,
+ },
+
+ .interface_modes = BIT(NL80211_IFTYPE_STATION) |
+ BIT(NL80211_IFTYPE_AP),
+ .supports_monitor = false,
+ .supports_shadow_regs = true,
+ .idle_ps = true,
+ .supports_sta_ps = true,
+ .cold_boot_calib = false,
+ .fw_mem_mode = 0,
+ .num_vdevs = 16 + 1,
+ .num_peers = 512,
+ .supports_suspend = false,
+ .supports_regdb = true,
+ .fix_l1ss = true,
+ .credit_flow = true,
+ .max_tx_ring = DP_TCL_NUM_RING_MAX_QCA6390,
+ .hal_params = &ath11k_hw_hal_params_qca6390,
+ .supports_dynamic_smps_6ghz = false,
+ .alloc_cacheable_memory = false,
+ .supports_rssi_stats = true,
+ .fw_wmi_diag_event = false,
+ },
};
int ath11k_core_suspend(struct ath11k_base *ab)
diff --git a/drivers/net/wireless/ath/ath11k/core.h b/drivers/net/wireless/ath/ath11k/core.h
index 9dd1904..803d977 100644
--- a/drivers/net/wireless/ath/ath11k/core.h
+++ b/drivers/net/wireless/ath/ath11k/core.h
@@ -119,6 +119,7 @@ enum ath11k_hw_rev {
ATH11K_HW_QCN9074_HW10,
ATH11K_HW_WCN6855_HW20,
ATH11K_HW_WCN6855_HW21,
+ ATH11K_HW_WCN6750_HW10,
};
enum ath11k_firmware_mode {
diff --git a/drivers/net/wireless/ath/ath11k/qmi.h b/drivers/net/wireless/ath/ath11k/qmi.h
index ba2eff4..404dbf8 100644
--- a/drivers/net/wireless/ath/ath11k/qmi.h
+++ b/drivers/net/wireless/ath/ath11k/qmi.h
@@ -1,6 +1,7 @@
/* SPDX-License-Identifier: BSD-3-Clause-Clear */
/*
* Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021, Qualcomm Innovation Center, Inc. All rights reserved.
*/
#ifndef ATH11K_QMI_H
@@ -20,6 +21,7 @@
#define ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_QCA6390 0x01
#define ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_IPQ8074 0x02
#define ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_QCN9074 0x07
+#define ATH11K_QMI_WLFW_SERVICE_INS_ID_V01_WCN6750 0x03
#define ATH11K_QMI_WLANFW_MAX_TIMESTAMP_LEN_V01 32
#define ATH11K_QMI_RESP_LEN_MAX 8192
#define ATH11K_QMI_WLANFW_MAX_NUM_MEM_SEG_V01 52
--
2.7.4
next prev parent reply other threads:[~2022-01-16 12:47 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-01-16 12:46 [PATCH v2 00/19] add support for WCN6750 Manikanta Pubbisetty
2022-01-16 12:46 ` [PATCH v2 01/19] ath11k: PCI changes to support WCN6750 Manikanta Pubbisetty
2022-01-16 12:46 ` [PATCH v2 02/19] ath11k: Refactor PCI code to support hybrid bus devices Manikanta Pubbisetty
2022-01-28 10:16 ` Kalle Valo
2022-02-25 5:50 ` Manikanta Pubbisetty
2022-03-08 6:00 ` Manikanta Pubbisetty
2022-01-28 12:13 ` Kalle Valo
2022-02-21 8:04 ` Manikanta Pubbisetty
2022-02-21 9:19 ` Kalle Valo
2022-02-21 10:19 ` Manikanta Pubbisetty
2022-01-16 12:46 ` [PATCH v2 03/19] ath11k: Choose MSI config based on HW revision Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 04/19] ath11k: Refactor MSI logic Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 05/19] ath11k: Remove core PCI references from PCI common code Manikanta Pubbisetty
2022-01-28 10:20 ` Kalle Valo
2022-01-28 10:37 ` Kalle Valo
2022-02-21 7:07 ` Manikanta Pubbisetty
2022-02-21 9:21 ` Kalle Valo
2022-02-21 6:55 ` Manikanta Pubbisetty
2022-02-21 9:17 ` Kalle Valo
2022-02-21 10:08 ` Manikanta Pubbisetty
2022-01-16 12:47 ` Manikanta Pubbisetty [this message]
2022-01-16 12:47 ` [PATCH v2 07/19] ath11k: Add bus params for WCN6750 Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 08/19] ath11k: Add register access logic " Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 09/19] ath11k: Fetch device information via QMI " Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 10/19] ath11k: Add QMI changes " Manikanta Pubbisetty
2022-01-28 10:50 ` Kalle Valo
2022-02-21 8:02 ` Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 11/19] ath11k: HAL changes to support WCN6750 Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 12/19] ath11k: Datapath " Manikanta Pubbisetty
2022-04-27 5:32 ` Kalle Valo
2022-04-27 5:37 ` Manikanta Pubbisetty
2022-04-27 5:48 ` Kalle Valo
2022-04-27 5:56 ` Manikanta Pubbisetty
2022-04-29 8:56 ` Kalle Valo
2022-01-16 12:47 ` [PATCH v2 13/19] ath11k: Fix RX de-fragmentation issue on WCN6750 Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 14/19] ath11k: Do not put HW in DBS mode for WCN6750 Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 15/19] ath11k: WMI changes to support WCN6750 Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 16/19] ath11k: Update WBM idle ring HP after FW mode on Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 17/19] ath11k: Add support for WCN6750 device Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 18/19] ath11k: Add support for targets without trustzone Manikanta Pubbisetty
2022-01-28 10:42 ` Kalle Valo
2022-02-21 8:00 ` Manikanta Pubbisetty
2022-01-16 12:47 ` [PATCH v2 19/19] dt: bindings: net: add bindings of WCN6750 for ath11k Manikanta Pubbisetty
2022-01-28 10:39 ` Kalle Valo
2022-02-21 7:08 ` Manikanta Pubbisetty
2022-02-07 22:13 ` Rob Herring
2022-02-25 11:34 ` Manikanta Pubbisetty
2022-01-28 10:07 ` [PATCH v2 00/19] add support for WCN6750 Kalle Valo
2022-02-21 6:29 ` Manikanta Pubbisetty
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1642337235-8618-7-git-send-email-quic_mpubbise@quicinc.com \
--to=quic_mpubbise@quicinc.com \
--cc=ath11k@lists.infradead.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).