[PATCH 0/8] iwlwifi: more fixes intended for 4.13 2017-08-01

[PATCH 0/8] iwlwifi: more fixes intended for 4.13 2017-08-01

[Luca Coelho]

From: Luca Coelho <luciano.coelho@intel.com>

Hi,

This is my second batch of fixes for 4.13.

The issues solved here are:

* Some simple PCI HW ID fix-ups and additions for family 9000;
* A couple of bugzilla fixes:
  - Remove a bogus warning message with new FWs (196915)
  - Don't allow illegal channel options to be used (195299)
* A fix for checksum offload in family 9000;
* A fix serious throughput degradation in 11ac with multiple streams;
* An old bug in SMPS where the firmware was not aware of SMPS changes;

As usual, I'm pushing this to a pending branch, for kbuild bot, and
will send a pull-request later.

Please review.

Cheers,
Luca.


Emmanuel Grumbach (3):
  iwlwifi: mvm: fix TCP CSUM offload with WEP and A000 series
  iwlwifi: add TLV for MLME offload firmware capability
  iwlwifi: split the regulatory rules when the bandwidth flags require
    it

Gregory Greenman (2):
  iwlwifi: mvm: set A-MPDU bit upon empty BA notification from FW
  iwlwifi: mvm: rs: fix TLC statistics collection

Haim Dreyfuss (1):
  iwlwifi: fix fw_pre_next_step to apply also for C step

Naftali Goldstein (1):
  iwlwifi: mvm: set the RTS_MIMO_PROT bit in flag mask when sending sta
    to fw

Tzipi Peres (1):
  iwlwifi: add the new 9000 series PCI IDs

 drivers/net/wireless/intel/iwlwifi/cfg/9000.c      | 14 +++++++-------
 drivers/net/wireless/intel/iwlwifi/fw/file.h       |  2 ++
 drivers/net/wireless/intel/iwlwifi/iwl-config.h    |  8 ++++----
 drivers/net/wireless/intel/iwlwifi/iwl-drv.c       |  5 +++--
 drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c | 19 +++++++++++--------
 drivers/net/wireless/intel/iwlwifi/mvm/rs.c        |  8 ++++----
 drivers/net/wireless/intel/iwlwifi/mvm/sta.c       |  3 ++-
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c        | 12 ++++++++++--
 drivers/net/wireless/intel/iwlwifi/pcie/drv.c      | 20 ++++++++++++++++++++
 9 files changed, 63 insertions(+), 28 deletions(-)

-- 
2.13.2

[PATCH 1/8] iwlwifi: mvm: fix TCP CSUM offload with WEP and A000 series

[Luca Coelho]

From: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.

On A000 devices series, the IV is always added by the
device.

Fix this.

Fixes: 5e6a98dc4863 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
index 60360ed73f26..e5d3eba2e82a 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -185,8 +185,14 @@ static u16 iwl_mvm_tx_csum(struct iwl_mvm *mvm, struct sk_buff *skb,
 	else
 		udp_hdr(skb)->check = 0;
 
-	/* mac header len should include IV, size is in words */
-	if (info->control.hw_key)
+	/*
+	 * mac header len should include IV, size is in words unless
+	 * the IV is added by the firmware like in WEP.
+	 * In new Tx API, the IV is always added by the firmware.
+	 */
+	if (!iwl_mvm_has_new_tx_api(mvm) && info->control.hw_key &&
+	    info->control.hw_key->cipher != WLAN_CIPHER_SUITE_WEP40 &&
+	    info->control.hw_key->cipher != WLAN_CIPHER_SUITE_WEP104)
 		mh_len += info->control.hw_key->iv_len;
 	mh_len /= 2;
 	offload_assist |= mh_len << TX_CMD_OFFLD_MH_SIZE;
-- 
2.13.2

[PATCH 2/8] iwlwifi: add TLV for MLME offload firmware capability

[Luca Coelho]

From: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.

This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/fw/file.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/fw/file.h b/drivers/net/wireless/intel/iwlwifi/fw/file.h
index 0fa8c473f1e2..c73a6438ce8f 100644
--- a/drivers/net/wireless/intel/iwlwifi/fw/file.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/file.h
@@ -328,6 +328,7 @@ typedef unsigned int __bitwise iwl_ucode_tlv_capa_t;
  * @IWL_UCODE_TLV_CAPA_TX_POWER_ACK: reduced TX power API has larger
  *	command size (command version 4) that supports toggling ACK TX
  *	power reduction.
+ * @IWL_UCODE_TLV_CAPA_MLME_OFFLOAD: supports MLME offload
  *
  * @NUM_IWL_UCODE_TLV_CAPA: number of bits used
  */
@@ -373,6 +374,7 @@ enum iwl_ucode_tlv_capa {
 	IWL_UCODE_TLV_CAPA_EXTEND_SHARED_MEM_CFG	= (__force iwl_ucode_tlv_capa_t)80,
 	IWL_UCODE_TLV_CAPA_LQM_SUPPORT			= (__force iwl_ucode_tlv_capa_t)81,
 	IWL_UCODE_TLV_CAPA_TX_POWER_ACK			= (__force iwl_ucode_tlv_capa_t)84,
+	IWL_UCODE_TLV_CAPA_MLME_OFFLOAD			= (__force iwl_ucode_tlv_capa_t)96,
 
 	NUM_IWL_UCODE_TLV_CAPA
 #ifdef __CHECKER__
-- 
2.13.2

[PATCH 3/8] iwlwifi: split the regulatory rules when the bandwidth flags require it

[Luca Coelho]

From: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since  (40, 44) is invalid.

Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.

Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.

Fixes: af45a9003f1f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c b/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
index 5c08f4d40f6a..3ee6767392b6 100644
--- a/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
+++ b/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
@@ -785,7 +785,8 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 		       int num_of_ch, __le32 *channels, u16 fw_mcc)
 {
 	int ch_idx;
-	u16 ch_flags, prev_ch_flags = 0;
+	u16 ch_flags;
+	u32 reg_rule_flags, prev_reg_rule_flags = 0;
 	const u8 *nvm_chan = cfg->ext_nvm ?
 			     iwl_ext_nvm_channels : iwl_nvm_channels;
 	struct ieee80211_regdomain *regd;
@@ -834,8 +835,11 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 			continue;
 		}
 
+		reg_rule_flags = iwl_nvm_get_regdom_bw_flags(nvm_chan, ch_idx,
+							     ch_flags, cfg);
+
 		/* we can't continue the same rule */
-		if (ch_idx == 0 || prev_ch_flags != ch_flags ||
+		if (ch_idx == 0 || prev_reg_rule_flags != reg_rule_flags ||
 		    center_freq - prev_center_freq > 20) {
 			valid_rules++;
 			new_rule = true;
@@ -854,18 +858,17 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 		rule->power_rule.max_eirp =
 			DBM_TO_MBM(IWL_DEFAULT_MAX_TX_POWER);
 
-		rule->flags = iwl_nvm_get_regdom_bw_flags(nvm_chan, ch_idx,
-							  ch_flags, cfg);
+		rule->flags = reg_rule_flags;
 
 		/* rely on auto-calculation to merge BW of contiguous chans */
 		rule->flags |= NL80211_RRF_AUTO_BW;
 		rule->freq_range.max_bandwidth_khz = 0;
 
-		prev_ch_flags = ch_flags;
 		prev_center_freq = center_freq;
+		prev_reg_rule_flags = reg_rule_flags;
 
 		IWL_DEBUG_DEV(dev, IWL_DL_LAR,
-			      "Ch. %d [%sGHz] %s%s%s%s%s%s%s%s%s(0x%02x): Ad-Hoc %ssupported\n",
+			      "Ch. %d [%sGHz] %s%s%s%s%s%s%s%s%s(0x%02x) reg_flags 0x%x: %s\n",
 			      center_freq,
 			      band == NL80211_BAND_5GHZ ? "5.2" : "2.4",
 			      CHECK_AND_PRINT_I(VALID),
@@ -877,10 +880,10 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 			      CHECK_AND_PRINT_I(160MHZ),
 			      CHECK_AND_PRINT_I(INDOOR_ONLY),
 			      CHECK_AND_PRINT_I(GO_CONCURRENT),
-			      ch_flags,
+			      ch_flags, reg_rule_flags,
 			      ((ch_flags & NVM_CHANNEL_ACTIVE) &&
 			       !(ch_flags & NVM_CHANNEL_RADAR))
-					 ? "" : "not ");
+					 ? "Ad-Hoc" : "");
 	}
 
 	regd->n_reg_rules = valid_rules;
-- 
2.13.2

[PATCH 4/8] iwlwifi: mvm: set A-MPDU bit upon empty BA notification from FW

[Luca Coelho]

From: Gregory Greenman <gregory.greenman@intel.com>

The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.

This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
index e5d3eba2e82a..5fcc9dd6be56 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -1821,6 +1821,8 @@ void iwl_mvm_rx_ba_notif(struct iwl_mvm *mvm, struct iwl_rx_cmd_buffer *rxb)
 	struct iwl_mvm_tid_data *tid_data;
 	struct iwl_mvm_sta *mvmsta;
 
+	ba_info.flags = IEEE80211_TX_STAT_AMPDU;
+
 	if (iwl_mvm_has_new_tx_api(mvm)) {
 		struct iwl_mvm_compressed_ba_notif *ba_res =
 			(void *)pkt->data;
-- 
2.13.2

[PATCH 5/8] iwlwifi: mvm: rs: fix TLC statistics collection

[Luca Coelho]

From: Gregory Greenman <gregory.greenman@intel.com>

Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).

This is needed to remove throughput degradation.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/mvm/rs.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
index 65beca3a457a..8999a1199d60 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/rs.c
@@ -1291,7 +1291,7 @@ void iwl_mvm_rs_tx_status(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
 	 * first index into rate scale table.
 	 */
 	if (info->flags & IEEE80211_TX_STAT_AMPDU) {
-		rs_collect_tpc_data(mvm, lq_sta, curr_tbl, lq_rate.index,
+		rs_collect_tpc_data(mvm, lq_sta, curr_tbl, tx_resp_rate.index,
 				    info->status.ampdu_len,
 				    info->status.ampdu_ack_len,
 				    reduced_txp);
@@ -1312,7 +1312,7 @@ void iwl_mvm_rs_tx_status(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
 		if (info->status.ampdu_ack_len == 0)
 			info->status.ampdu_len = 1;
 
-		rs_collect_tlc_data(mvm, lq_sta, curr_tbl, lq_rate.index,
+		rs_collect_tlc_data(mvm, lq_sta, curr_tbl, tx_resp_rate.index,
 				    info->status.ampdu_len,
 				    info->status.ampdu_ack_len);
 
@@ -1348,11 +1348,11 @@ void iwl_mvm_rs_tx_status(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
 				continue;
 
 			rs_collect_tpc_data(mvm, lq_sta, tmp_tbl,
-					    lq_rate.index, 1,
+					    tx_resp_rate.index, 1,
 					    i < retries ? 0 : legacy_success,
 					    reduced_txp);
 			rs_collect_tlc_data(mvm, lq_sta, tmp_tbl,
-					    lq_rate.index, 1,
+					    tx_resp_rate.index, 1,
 					    i < retries ? 0 : legacy_success);
 		}
 
-- 
2.13.2

[PATCH 6/8] iwlwifi: fix fw_pre_next_step to apply also for C step

[Luca Coelho]

From: Haim Dreyfuss <haim.dreyfuss@intel.com>

C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.

Fixes: 5da083d1922c ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/cfg/9000.c   | 14 +++++++-------
 drivers/net/wireless/intel/iwlwifi/iwl-config.h |  8 ++++----
 drivers/net/wireless/intel/iwlwifi/iwl-drv.c    |  5 +++--
 3 files changed, 14 insertions(+), 13 deletions(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/cfg/9000.c b/drivers/net/wireless/intel/iwlwifi/cfg/9000.c
index b4ecd1fe1374..97208ce19f92 100644
--- a/drivers/net/wireless/intel/iwlwifi/cfg/9000.c
+++ b/drivers/net/wireless/intel/iwlwifi/cfg/9000.c
@@ -154,7 +154,7 @@ static const struct iwl_tt_params iwl9000_tt_params = {
 const struct iwl_cfg iwl9160_2ac_cfg = {
 	.name = "Intel(R) Dual Band Wireless AC 9160",
 	.fw_name_pre = IWL9260A_FW_PRE,
-	.fw_name_pre_next_step = IWL9260B_FW_PRE,
+	.fw_name_pre_b_or_c_step = IWL9260B_FW_PRE,
 	IWL_DEVICE_9000,
 	.ht_params = &iwl9000_ht_params,
 	.nvm_ver = IWL9000_NVM_VERSION,
@@ -165,7 +165,7 @@ const struct iwl_cfg iwl9160_2ac_cfg = {
 const struct iwl_cfg iwl9260_2ac_cfg = {
 	.name = "Intel(R) Dual Band Wireless AC 9260",
 	.fw_name_pre = IWL9260A_FW_PRE,
-	.fw_name_pre_next_step = IWL9260B_FW_PRE,
+	.fw_name_pre_b_or_c_step = IWL9260B_FW_PRE,
 	IWL_DEVICE_9000,
 	.ht_params = &iwl9000_ht_params,
 	.nvm_ver = IWL9000_NVM_VERSION,
@@ -176,7 +176,7 @@ const struct iwl_cfg iwl9260_2ac_cfg = {
 const struct iwl_cfg iwl9270_2ac_cfg = {
 	.name = "Intel(R) Dual Band Wireless AC 9270",
 	.fw_name_pre = IWL9260A_FW_PRE,
-	.fw_name_pre_next_step = IWL9260B_FW_PRE,
+	.fw_name_pre_b_or_c_step = IWL9260B_FW_PRE,
 	IWL_DEVICE_9000,
 	.ht_params = &iwl9000_ht_params,
 	.nvm_ver = IWL9000_NVM_VERSION,
@@ -186,8 +186,8 @@ const struct iwl_cfg iwl9270_2ac_cfg = {
 
 const struct iwl_cfg iwl9460_2ac_cfg = {
 	.name = "Intel(R) Dual Band Wireless AC 9460",
-	.fw_name_pre = IWL9000_FW_PRE,
-	.fw_name_pre_rf_next_step = IWL9000RFB_FW_PRE,
+	.fw_name_pre = IWL9260A_FW_PRE,
+	.fw_name_pre_b_or_c_step = IWL9260B_FW_PRE,
 	IWL_DEVICE_9000,
 	.ht_params = &iwl9000_ht_params,
 	.nvm_ver = IWL9000_NVM_VERSION,
@@ -198,8 +198,8 @@ const struct iwl_cfg iwl9460_2ac_cfg = {
 
 const struct iwl_cfg iwl9560_2ac_cfg = {
 	.name = "Intel(R) Dual Band Wireless AC 9560",
-	.fw_name_pre = IWL9000_FW_PRE,
-	.fw_name_pre_rf_next_step = IWL9000RFB_FW_PRE,
+	.fw_name_pre = IWL9260A_FW_PRE,
+	.fw_name_pre_b_or_c_step = IWL9260B_FW_PRE,
 	IWL_DEVICE_9000,
 	.ht_params = &iwl9000_ht_params,
 	.nvm_ver = IWL9000_NVM_VERSION,
diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-config.h b/drivers/net/wireless/intel/iwlwifi/iwl-config.h
index c52623cb7c2a..d19c74827fbb 100644
--- a/drivers/net/wireless/intel/iwlwifi/iwl-config.h
+++ b/drivers/net/wireless/intel/iwlwifi/iwl-config.h
@@ -276,10 +276,10 @@ struct iwl_pwr_tx_backoff {
  * @fw_name_pre: Firmware filename prefix. The api version and extension
  *	(.ucode) will be added to filename before loading from disk. The
  *	filename is constructed as fw_name_pre<api>.ucode.
- * @fw_name_pre_next_step: same as @fw_name_pre, only for next step
+ * @fw_name_pre_b_or_c_step: same as @fw_name_pre, only for b or c steps
  *	(if supported)
- * @fw_name_pre_rf_next_step: same as @fw_name_pre_next_step, only for rf next
- *	step. Supported only in integrated solutions.
+ * @fw_name_pre_rf_next_step: same as @fw_name_pre_b_or_c_step, only for rf
+ *	next step. Supported only in integrated solutions.
  * @ucode_api_max: Highest version of uCode API supported by driver.
  * @ucode_api_min: Lowest version of uCode API supported by driver.
  * @max_inst_size: The maximal length of the fw inst section
@@ -330,7 +330,7 @@ struct iwl_cfg {
 	/* params specific to an individual device within a device family */
 	const char *name;
 	const char *fw_name_pre;
-	const char *fw_name_pre_next_step;
+	const char *fw_name_pre_b_or_c_step;
 	const char *fw_name_pre_rf_next_step;
 	/* params not likely to change within a device family */
 	const struct iwl_base_params *base_params;
diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-drv.c b/drivers/net/wireless/intel/iwlwifi/iwl-drv.c
index 6fdb5921e17f..4e0f86fe0a6f 100644
--- a/drivers/net/wireless/intel/iwlwifi/iwl-drv.c
+++ b/drivers/net/wireless/intel/iwlwifi/iwl-drv.c
@@ -216,8 +216,9 @@ static int iwl_request_firmware(struct iwl_drv *drv, bool first)
 	const char *fw_pre_name;
 
 	if (drv->trans->cfg->device_family == IWL_DEVICE_FAMILY_9000 &&
-	    CSR_HW_REV_STEP(drv->trans->hw_rev) == SILICON_B_STEP)
-		fw_pre_name = cfg->fw_name_pre_next_step;
+	    (CSR_HW_REV_STEP(drv->trans->hw_rev) == SILICON_B_STEP ||
+	     CSR_HW_REV_STEP(drv->trans->hw_rev) == SILICON_C_STEP))
+		fw_pre_name = cfg->fw_name_pre_b_or_c_step;
 	else if (drv->trans->cfg->integrated &&
 		 CSR_HW_RFID_STEP(drv->trans->hw_rf_id) == SILICON_B_STEP &&
 		 cfg->fw_name_pre_rf_next_step)
-- 
2.13.2

[PATCH 7/8] iwlwifi: mvm: set the RTS_MIMO_PROT bit in flag mask when sending sta to fw

[Luca Coelho]

From: Naftali Goldstein <naftali.goldstein@intel.com>

Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.

In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.

Fixes: 5bc5aaad407c ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/mvm/sta.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/sta.c b/drivers/net/wireless/intel/iwlwifi/mvm/sta.c
index ab66b4394dfc..dcaef7c043ac 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/sta.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/sta.c
@@ -121,7 +121,8 @@ int iwl_mvm_sta_send_to_fw(struct iwl_mvm *mvm, struct ieee80211_sta *sta,
 		.mac_id_n_color = cpu_to_le32(mvm_sta->mac_id_n_color),
 		.add_modify = update ? 1 : 0,
 		.station_flags_msk = cpu_to_le32(STA_FLG_FAT_EN_MSK |
-						 STA_FLG_MIMO_EN_MSK),
+						 STA_FLG_MIMO_EN_MSK |
+						 STA_FLG_RTS_MIMO_PROT),
 		.tid_disable_tx = cpu_to_le16(mvm_sta->tid_disable_agg),
 	};
 	int ret;
-- 
2.13.2

[PATCH 8/8] iwlwifi: add the new 9000 series PCI IDs

[Luca Coelho]

From: Tzipi Peres <tzipi.peres@intel.com>

Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.

Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
---
 drivers/net/wireless/intel/iwlwifi/pcie/drv.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/pcie/drv.c b/drivers/net/wireless/intel/iwlwifi/pcie/drv.c
index f16c1bb9bf94..84f4ba01e14f 100644
--- a/drivers/net/wireless/intel/iwlwifi/pcie/drv.c
+++ b/drivers/net/wireless/intel/iwlwifi/pcie/drv.c
@@ -510,9 +510,17 @@ static const struct pci_device_id iwl_hw_card_ids[] = {
 
 /* 9000 Series */
 	{IWL_PCI_DEVICE(0x271B, 0x0010, iwl9160_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x271B, 0x0014, iwl9160_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x271B, 0x0210, iwl9160_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x2526, 0x0000, iwl9260_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x2526, 0x0010, iwl9260_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0014, iwl9260_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0xA014, iwl9260_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x4010, iwl9260_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0210, iwl9260_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0214, iwl9260_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x2526, 0x1410, iwl9270_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x1610, iwl9270_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x9DF0, 0x0A10, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x9DF0, 0x0010, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x9DF0, 0x0210, iwl9460_2ac_cfg)},
@@ -527,10 +535,22 @@ static const struct pci_device_id iwl_hw_card_ids[] = {
 	{IWL_PCI_DEVICE(0x9DF0, 0x2A10, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x30DC, 0x0060, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x2526, 0x0060, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0260, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0064, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x00A4, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x40A4, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x02A4, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x00A0, iwl9460_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x02A0, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x9DF0, 0x0060, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0xA370, 0x0060, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x31DC, 0x0060, iwl9460_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x2526, 0x0030, iwl9560_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x4030, iwl9560_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0230, iwl9560_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0234, iwl9560_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x0238, iwl9560_2ac_cfg)},
+	{IWL_PCI_DEVICE(0x2526, 0x023C, iwl9560_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x9DF0, 0x0030, iwl9560_2ac_cfg)},
 	{IWL_PCI_DEVICE(0xA370, 0x0030, iwl9560_2ac_cfg)},
 	{IWL_PCI_DEVICE(0x31DC, 0x0030, iwl9560_2ac_cfg)},
-- 
2.13.2