[PATCH AUTOSEL 4.9 01/64] ath10k: fix kernel panic by moving pci flush after napi_disable

[PATCH AUTOSEL 4.9 01/64] ath10k: fix kernel panic by moving pci flush after napi_disable

[Sasha Levin]

From: Tamizh chelvam <tamizhr@codeaurora.org>

[ Upstream commit bd1d395070cca4f42a93e520b0597274789274a4 ]

When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush

Steps:
  In a certain condition, during wifi down below scenario might occur.

ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).

In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.

Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60

Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010

Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/ahb.c | 4 ++--
 drivers/net/wireless/ath/ath10k/pci.c | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/ahb.c b/drivers/net/wireless/ath/ath10k/ahb.c
index da770af830369..125b5c31b2b0a 100644
--- a/drivers/net/wireless/ath/ath10k/ahb.c
+++ b/drivers/net/wireless/ath/ath10k/ahb.c
@@ -658,10 +658,10 @@ static void ath10k_ahb_hif_stop(struct ath10k *ar)
 	ath10k_ahb_irq_disable(ar);
 	synchronize_irq(ar_ahb->irq);
 
-	ath10k_pci_flush(ar);
-
 	napi_synchronize(&ar->napi);
 	napi_disable(&ar->napi);
+
+	ath10k_pci_flush(ar);
 }
 
 static int ath10k_ahb_hif_power_up(struct ath10k *ar)
diff --git a/drivers/net/wireless/ath/ath10k/pci.c b/drivers/net/wireless/ath/ath10k/pci.c
index 25b8d501d437e..b7bac14d1487b 100644
--- a/drivers/net/wireless/ath/ath10k/pci.c
+++ b/drivers/net/wireless/ath/ath10k/pci.c
@@ -1781,9 +1781,9 @@ static void ath10k_pci_hif_stop(struct ath10k *ar)
 
 	ath10k_pci_irq_disable(ar);
 	ath10k_pci_irq_sync(ar);
-	ath10k_pci_flush(ar);
 	napi_synchronize(&ar->napi);
 	napi_disable(&ar->napi);
+	ath10k_pci_flush(ar);
 
 	spin_lock_irqsave(&ar_pci->ps_lock, flags);
 	WARN_ON(ar_pci->ps_wake_refcount > 0);
-- 
2.20.1

[PATCH AUTOSEL 4.9 06/64] cfg80211: Avoid regulatory restore when COUNTRY_IE_IGNORE is set

[Sasha Levin]

From: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>

[ Upstream commit 7417844b63d4b0dc8ab23f88259bf95de7d09b57 ]

When REGULATORY_COUNTRY_IE_IGNORE is set,  __reg_process_hint_country_ie()
ignores the country code change request from __cfg80211_connect_result()
via regulatory_hint_country_ie().

After Disconnect, similar to above, country code should not be reset to
world when country IE ignore is set. But this is violated and restore of
regulatory settings is invoked by cfg80211_disconnect_work via
regulatory_hint_disconnect().

To address this, avoid regulatory restore from regulatory_hint_disconnect()
when COUNTRY_IE_IGNORE is set.

Note: Currently, restore_regulatory_settings() takes care of clearing
beacon hints. But in the proposed change, regulatory restore is avoided.
Therefore, explicitly clear beacon hints when DISABLE_BEACON_HINTS
is not set.

Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 net/wireless/reg.c | 46 ++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 46 insertions(+)

diff --git a/net/wireless/reg.c b/net/wireless/reg.c
index 44befe9f9ff08..dde741f298de7 100644
--- a/net/wireless/reg.c
+++ b/net/wireless/reg.c
@@ -2616,8 +2616,54 @@ static void restore_regulatory_settings(bool reset_user)
 	schedule_work(&reg_work);
 }
 
+static bool is_wiphy_all_set_reg_flag(enum ieee80211_regulatory_flags flag)
+{
+	struct cfg80211_registered_device *rdev;
+	struct wireless_dev *wdev;
+
+	list_for_each_entry(rdev, &cfg80211_rdev_list, list) {
+		list_for_each_entry(wdev, &rdev->wiphy.wdev_list, list) {
+			wdev_lock(wdev);
+			if (!(wdev->wiphy->regulatory_flags & flag)) {
+				wdev_unlock(wdev);
+				return false;
+			}
+			wdev_unlock(wdev);
+		}
+	}
+
+	return true;
+}
+
 void regulatory_hint_disconnect(void)
 {
+	/* Restore of regulatory settings is not required when wiphy(s)
+	 * ignore IE from connected access point but clearance of beacon hints
+	 * is required when wiphy(s) supports beacon hints.
+	 */
+	if (is_wiphy_all_set_reg_flag(REGULATORY_COUNTRY_IE_IGNORE)) {
+		struct reg_beacon *reg_beacon, *btmp;
+
+		if (is_wiphy_all_set_reg_flag(REGULATORY_DISABLE_BEACON_HINTS))
+			return;
+
+		spin_lock_bh(&reg_pending_beacons_lock);
+		list_for_each_entry_safe(reg_beacon, btmp,
+					 &reg_pending_beacons, list) {
+			list_del(&reg_beacon->list);
+			kfree(reg_beacon);
+		}
+		spin_unlock_bh(&reg_pending_beacons_lock);
+
+		list_for_each_entry_safe(reg_beacon, btmp,
+					 &reg_beacon_list, list) {
+			list_del(&reg_beacon->list);
+			kfree(reg_beacon);
+		}
+
+		return;
+	}
+
 	pr_debug("All devices are disconnected, going to restore regulatory settings\n");
 	restore_regulatory_settings(false);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.9 08/64] ath9k: fix tx99 with monitor mode interface

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit d9c52fd17cb483bd8a470398afcb79f86c1b77c8 ]

Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/ath9k.h |  1 -
 drivers/net/wireless/ath/ath9k/main.c  | 12 +++---------
 drivers/net/wireless/ath/ath9k/tx99.c  |  9 ---------
 drivers/net/wireless/ath/ath9k/xmit.c  |  2 +-
 4 files changed, 4 insertions(+), 20 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ath9k.h b/drivers/net/wireless/ath/ath9k/ath9k.h
index 7bda18c61eb6e..51e878a9d5211 100644
--- a/drivers/net/wireless/ath/ath9k/ath9k.h
+++ b/drivers/net/wireless/ath/ath9k/ath9k.h
@@ -1033,7 +1033,6 @@ struct ath_softc {
 
 	struct ath_spec_scan_priv spec_priv;
 
-	struct ieee80211_vif *tx99_vif;
 	struct sk_buff *tx99_skb;
 	bool tx99_state;
 	s16 tx99_power;
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index b868f02ced893..fbc34beee1580 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1249,15 +1249,10 @@ static int ath9k_add_interface(struct ieee80211_hw *hw,
 	struct ath_vif *avp = (void *)vif->drv_priv;
 	struct ath_node *an = &avp->mcast_node;
 
-	mutex_lock(&sc->mutex);
+	if (IS_ENABLED(CONFIG_ATH9K_TX99))
+		return -EOPNOTSUPP;
 
-	if (IS_ENABLED(CONFIG_ATH9K_TX99)) {
-		if (sc->cur_chan->nvifs >= 1) {
-			mutex_unlock(&sc->mutex);
-			return -EOPNOTSUPP;
-		}
-		sc->tx99_vif = vif;
-	}
+	mutex_lock(&sc->mutex);
 
 	ath_dbg(common, CONFIG, "Attach a VIF of type: %d\n", vif->type);
 	sc->cur_chan->nvifs++;
@@ -1340,7 +1335,6 @@ static void ath9k_remove_interface(struct ieee80211_hw *hw,
 	ath9k_p2p_remove_vif(sc, vif);
 
 	sc->cur_chan->nvifs--;
-	sc->tx99_vif = NULL;
 	if (!ath9k_is_chanctx_enabled())
 		list_del(&avp->list);
 
diff --git a/drivers/net/wireless/ath/ath9k/tx99.c b/drivers/net/wireless/ath/ath9k/tx99.c
index 8e9480cc33e15..0cb5b2a873be8 100644
--- a/drivers/net/wireless/ath/ath9k/tx99.c
+++ b/drivers/net/wireless/ath/ath9k/tx99.c
@@ -54,12 +54,6 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
 	struct ieee80211_hdr *hdr;
 	struct ieee80211_tx_info *tx_info;
 	struct sk_buff *skb;
-	struct ath_vif *avp;
-
-	if (!sc->tx99_vif)
-		return NULL;
-
-	avp = (struct ath_vif *)sc->tx99_vif->drv_priv;
 
 	skb = alloc_skb(len, GFP_KERNEL);
 	if (!skb)
@@ -77,14 +71,11 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
 	memcpy(hdr->addr2, hw->wiphy->perm_addr, ETH_ALEN);
 	memcpy(hdr->addr3, hw->wiphy->perm_addr, ETH_ALEN);
 
-	hdr->seq_ctrl |= cpu_to_le16(avp->seq_no);
-
 	tx_info = IEEE80211_SKB_CB(skb);
 	memset(tx_info, 0, sizeof(*tx_info));
 	rate = &tx_info->control.rates[0];
 	tx_info->band = sc->cur_chan->chandef.chan->band;
 	tx_info->flags = IEEE80211_TX_CTL_NO_ACK;
-	tx_info->control.vif = sc->tx99_vif;
 	rate->count = 1;
 	if (ah->curchan && IS_CHAN_HT(ah->curchan)) {
 		rate->flags |= IEEE80211_TX_RC_MCS;
diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c
index 0ef27d99bef33..2c35819f65426 100644
--- a/drivers/net/wireless/ath/ath9k/xmit.c
+++ b/drivers/net/wireless/ath/ath9k/xmit.c
@@ -2970,7 +2970,7 @@ int ath9k_tx99_send(struct ath_softc *sc, struct sk_buff *skb,
 		return -EINVAL;
 	}
 
-	ath_set_rates(sc->tx99_vif, NULL, bf);
+	ath_set_rates(NULL, NULL, bf);
 
 	ath9k_hw_set_desc_link(sc->sc_ah, bf->bf_desc, bf->bf_daddr);
 	ath9k_hw_tx99_start(sc->sc_ah, txctl->txq->axq_qnum);
-- 
2.20.1

[PATCH AUTOSEL 4.9 18/64] iwlwifi: mvm: avoid sending too many BARs

[Sasha Levin]

From: Sara Sharon <sara.sharon@intel.com>

[ Upstream commit 1a19c139be18ed4d6d681049cc48586fae070120 ]

When we receive TX response, we may release a few packets
due to a hole that was closed in the transmission window.

However, if that frame failed, we will mark all the released
frames as failed and will send multiple BARs.

This affects statistics badly, and cause unnecessary frames
transmission.

Instead, mark all the following packets as success, with the
desired result of sending a bar for the failed frame only.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/intel/iwlwifi/mvm/tx.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
index 1aa74b87599ff..63dcea640d076 100644
--- a/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/tx.c
@@ -1303,6 +1303,14 @@ static void iwl_mvm_rx_tx_cmd_single(struct iwl_mvm *mvm,
 			break;
 		}
 
+		/*
+		 * If we are freeing multiple frames, mark all the frames
+		 * but the first one as acked, since they were acknowledged
+		 * before
+		 * */
+		if (skb_freed > 1)
+			info->flags |= IEEE80211_TX_STAT_ACK;
+
 		iwl_mvm_tx_status_check_trigger(mvm, status);
 
 		info->status.rates[0].count = tx_resp->failure_frame + 1;
-- 
2.20.1

[PATCH AUTOSEL 4.9 20/64] rtl8187: Fix warning generated when strncpy() destination length matches the sixe argument

[Sasha Levin]

From: Larry Finger <Larry.Finger@lwfinger.net>

[ Upstream commit 199ba9faca909e77ac533449ecd1248123ce89e7 ]

In gcc8, when the 3rd argument (size) of a call to strncpy() matches the
length of the first argument, the compiler warns of the possibility of an
unterminated string. Using strlcpy() forces a null at the end.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/realtek/rtl818x/rtl8187/leds.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/realtek/rtl818x/rtl8187/leds.c b/drivers/net/wireless/realtek/rtl818x/rtl8187/leds.c
index c2d5b495c179a..c089540116fa7 100644
--- a/drivers/net/wireless/realtek/rtl818x/rtl8187/leds.c
+++ b/drivers/net/wireless/realtek/rtl818x/rtl8187/leds.c
@@ -146,7 +146,7 @@ static int rtl8187_register_led(struct ieee80211_hw *dev,
 	led->dev = dev;
 	led->ledpin = ledpin;
 	led->is_radio = is_radio;
-	strncpy(led->name, name, sizeof(led->name));
+	strlcpy(led->name, name, sizeof(led->name));
 
 	led->led_dev.name = led->name;
 	led->led_dev.default_trigger = default_trigger;
-- 
2.20.1

[PATCH AUTOSEL 4.9 24/64] ath10k: wmi: disable softirq's while calling ieee80211_rx

[Sasha Levin]

From: Erik Stromdahl <erik.stromdahl@gmail.com>

[ Upstream commit 37f62c0d5822f631b786b29a1b1069ab714d1a28 ]

This is done in order not to trig the below warning in
ieee80211_rx_napi:

WARN_ON_ONCE(softirq_count() == 0);

ieee80211_rx_napi requires that softirq's are disabled during
execution.

The High latency bus drivers (SDIO and USB) sometimes call the wmi
ep_rx_complete callback from non softirq context, resulting in a trigger
of the above warning.

Calling ieee80211_rx_ni with softirq's already disabled (e.g., from
softirq context) should be safe as the local_bh_disable and
local_bh_enable functions (called from ieee80211_rx_ni) are fully
reentrant.

Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/wmi.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/wmi.c b/drivers/net/wireless/ath/ath10k/wmi.c
index bbfe7be214e12..c208fed048554 100644
--- a/drivers/net/wireless/ath/ath10k/wmi.c
+++ b/drivers/net/wireless/ath/ath10k/wmi.c
@@ -2384,7 +2384,8 @@ int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb)
 		   status->freq, status->band, status->signal,
 		   status->rate_idx);
 
-	ieee80211_rx(ar->hw, skb);
+	ieee80211_rx_ni(ar->hw, skb);
+
 	return 0;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.9 36/64] ath9k: add back support for using active monitor interfaces for tx99

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 6df0580be8bc30803c4d8b2ed9c2230a2740c795 ]

Various documented examples on how to set up tx99 with ath9k rely
on setting up a regular monitor interface for setting the channel.
My previous patch "ath9k: fix tx99 with monitor mode interface" made
it possible to set it up this way again. However, it was removing support
for using an active monitor interface, which is required for controlling
the bitrate as well, since the bitrate is not passed down with a regular
monitor interface.

This patch partially reverts the previous one, but keeps support for using
a regular monitor interface to keep documented steps working in cases
where the bitrate does not matter

Fixes: d9c52fd17cb48 ("ath9k: fix tx99 with monitor mode interface")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/ath9k.h |  1 +
 drivers/net/wireless/ath/ath9k/main.c  | 10 ++++++++--
 drivers/net/wireless/ath/ath9k/tx99.c  |  7 +++++++
 drivers/net/wireless/ath/ath9k/xmit.c  |  2 +-
 4 files changed, 17 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/ath9k.h b/drivers/net/wireless/ath/ath9k/ath9k.h
index 51e878a9d5211..7bda18c61eb6e 100644
--- a/drivers/net/wireless/ath/ath9k/ath9k.h
+++ b/drivers/net/wireless/ath/ath9k/ath9k.h
@@ -1033,6 +1033,7 @@ struct ath_softc {
 
 	struct ath_spec_scan_priv spec_priv;
 
+	struct ieee80211_vif *tx99_vif;
 	struct sk_buff *tx99_skb;
 	bool tx99_state;
 	s16 tx99_power;
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index fbc34beee1580..f6151a00041d6 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1249,8 +1249,13 @@ static int ath9k_add_interface(struct ieee80211_hw *hw,
 	struct ath_vif *avp = (void *)vif->drv_priv;
 	struct ath_node *an = &avp->mcast_node;
 
-	if (IS_ENABLED(CONFIG_ATH9K_TX99))
-		return -EOPNOTSUPP;
+	if (IS_ENABLED(CONFIG_ATH9K_TX99)) {
+		if (sc->cur_chan->nvifs >= 1) {
+			mutex_unlock(&sc->mutex);
+			return -EOPNOTSUPP;
+		}
+		sc->tx99_vif = vif;
+	}
 
 	mutex_lock(&sc->mutex);
 
@@ -1335,6 +1340,7 @@ static void ath9k_remove_interface(struct ieee80211_hw *hw,
 	ath9k_p2p_remove_vif(sc, vif);
 
 	sc->cur_chan->nvifs--;
+	sc->tx99_vif = NULL;
 	if (!ath9k_is_chanctx_enabled())
 		list_del(&avp->list);
 
diff --git a/drivers/net/wireless/ath/ath9k/tx99.c b/drivers/net/wireless/ath/ath9k/tx99.c
index 0cb5b2a873be8..096902e0fdf5c 100644
--- a/drivers/net/wireless/ath/ath9k/tx99.c
+++ b/drivers/net/wireless/ath/ath9k/tx99.c
@@ -54,6 +54,7 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
 	struct ieee80211_hdr *hdr;
 	struct ieee80211_tx_info *tx_info;
 	struct sk_buff *skb;
+	struct ath_vif *avp;
 
 	skb = alloc_skb(len, GFP_KERNEL);
 	if (!skb)
@@ -71,11 +72,17 @@ static struct sk_buff *ath9k_build_tx99_skb(struct ath_softc *sc)
 	memcpy(hdr->addr2, hw->wiphy->perm_addr, ETH_ALEN);
 	memcpy(hdr->addr3, hw->wiphy->perm_addr, ETH_ALEN);
 
+	if (sc->tx99_vif) {
+		avp = (struct ath_vif *) sc->tx99_vif->drv_priv;
+		hdr->seq_ctrl |= cpu_to_le16(avp->seq_no);
+	}
+
 	tx_info = IEEE80211_SKB_CB(skb);
 	memset(tx_info, 0, sizeof(*tx_info));
 	rate = &tx_info->control.rates[0];
 	tx_info->band = sc->cur_chan->chandef.chan->band;
 	tx_info->flags = IEEE80211_TX_CTL_NO_ACK;
+	tx_info->control.vif = sc->tx99_vif;
 	rate->count = 1;
 	if (ah->curchan && IS_CHAN_HT(ah->curchan)) {
 		rate->flags |= IEEE80211_TX_RC_MCS;
diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c
index 2c35819f65426..0ef27d99bef33 100644
--- a/drivers/net/wireless/ath/ath9k/xmit.c
+++ b/drivers/net/wireless/ath/ath9k/xmit.c
@@ -2970,7 +2970,7 @@ int ath9k_tx99_send(struct ath_softc *sc, struct sk_buff *skb,
 		return -EINVAL;
 	}
 
-	ath_set_rates(NULL, NULL, bf);
+	ath_set_rates(sc->tx99_vif, NULL, bf);
 
 	ath9k_hw_set_desc_link(sc->sc_ah, bf->bf_desc, bf->bf_daddr);
 	ath9k_hw_tx99_start(sc->sc_ah, txctl->txq->axq_qnum);
-- 
2.20.1

[PATCH AUTOSEL 4.9 64/64] ath9k: Fix a locking bug in ath9k_add_interface()

[Sasha Levin]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit 461cf036057477805a8a391e5fd0f5264a5e56a8 ]

We tried to revert commit d9c52fd17cb4 ("ath9k: fix tx99 with monitor
mode interface") but accidentally missed part of the locking change.

The lock has to be held earlier so that we're holding it when we do
"sc->tx99_vif = vif;" and also there in the current code there is a
stray unlock before we have taken the lock.

Fixes: 6df0580be8bc ("ath9k: add back support for using active monitor interfaces for tx99")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath9k/main.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index f6151a00041d6..abc997427bae5 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1249,6 +1249,7 @@ static int ath9k_add_interface(struct ieee80211_hw *hw,
 	struct ath_vif *avp = (void *)vif->drv_priv;
 	struct ath_node *an = &avp->mcast_node;
 
+	mutex_lock(&sc->mutex);
 	if (IS_ENABLED(CONFIG_ATH9K_TX99)) {
 		if (sc->cur_chan->nvifs >= 1) {
 			mutex_unlock(&sc->mutex);
@@ -1257,8 +1258,6 @@ static int ath9k_add_interface(struct ieee80211_hw *hw,
 		sc->tx99_vif = vif;
 	}
 
-	mutex_lock(&sc->mutex);
-
 	ath_dbg(common, CONFIG, "Attach a VIF of type: %d\n", vif->type);
 	sc->cur_chan->nvifs++;
 
-- 
2.20.1