* [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT
@ 2020-04-22 16:04 Felix Fietkau
2020-04-22 16:04 ` [PATCH 2/9] mt76: fix A-MPDU density handling Felix Fietkau
` (7 more replies)
0 siblings, 8 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
If VHT has a larger A-MPDU size limit, pass it to the MCU via the wtbl_ht
TLV element.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c | 11 +++++++++--
1 file changed, 9 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
index dc297856b749..24b78d10d7f7 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
@@ -924,11 +924,10 @@ mt7615_mcu_wtbl_ht_tlv(struct sk_buff *skb, struct ieee80211_sta *sta,
void *sta_wtbl, void *wtbl_tlv)
{
struct tlv *tlv;
+ struct wtbl_ht *ht = NULL;
u32 flags = 0;
if (sta->ht_cap.ht_supported) {
- struct wtbl_ht *ht;
-
tlv = mt7615_mcu_add_nested_tlv(skb, WTBL_HT, sizeof(*ht),
wtbl_tlv, sta_wtbl);
ht = (struct wtbl_ht *)tlv;
@@ -945,6 +944,7 @@ mt7615_mcu_wtbl_ht_tlv(struct sk_buff *skb, struct ieee80211_sta *sta,
if (sta->vht_cap.vht_supported) {
struct wtbl_vht *vht;
+ u8 af;
tlv = mt7615_mcu_add_nested_tlv(skb, WTBL_VHT, sizeof(*vht),
wtbl_tlv, sta_wtbl);
@@ -952,6 +952,13 @@ mt7615_mcu_wtbl_ht_tlv(struct sk_buff *skb, struct ieee80211_sta *sta,
vht->ldpc = sta->vht_cap.cap & IEEE80211_VHT_CAP_RXLDPC,
vht->vht = 1;
+ af = (sta->vht_cap.cap &
+ IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK) >>
+ IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT;
+
+ if (ht)
+ ht->af = max(ht->af, af);
+
if (sta->vht_cap.cap & IEEE80211_VHT_CAP_SHORT_GI_80)
flags |= MT_WTBL_W5_SHORT_GI_80;
if (sta->vht_cap.cap & IEEE80211_VHT_CAP_SHORT_GI_160)
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 2/9] mt76: fix A-MPDU density handling
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 3/9] mt76: mt7615: use larger rx buffers if VHT is supported Felix Fietkau
` (6 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
The hardware requirements for A-MPDU density are entirely on the tx side,
not the rx side. Because of that, the IE value should stay at 0 and the
minimum value should instead be enforced in WTBL/TXWI
MT7615 has no restrictions here
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mac80211.c | 1 -
drivers/net/wireless/mediatek/mt76/mt7603/mac.c | 5 +++++
drivers/net/wireless/mediatek/mt76/mt76x02_mac.c | 7 +++++--
3 files changed, 10 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mac80211.c b/drivers/net/wireless/mediatek/mt76/mac80211.c
index 39abedc45e4a..b6c0a6d0dfc1 100644
--- a/drivers/net/wireless/mediatek/mt76/mac80211.c
+++ b/drivers/net/wireless/mediatek/mt76/mac80211.c
@@ -198,7 +198,6 @@ mt76_init_sband(struct mt76_dev *dev, struct mt76_sband *msband,
ht_cap->mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED;
ht_cap->ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K;
- ht_cap->ampdu_density = IEEE80211_HT_MPDU_DENSITY_4;
mt76_init_stream_cap(dev, sband, vht);
diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
index 39b7c5d6e6cd..73c6a3ff399c 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
@@ -318,11 +318,16 @@ void mt7603_wtbl_update_cap(struct mt7603_dev *dev, struct ieee80211_sta *sta)
{
struct mt7603_sta *msta = (struct mt7603_sta *)sta->drv_priv;
int idx = msta->wcid.idx;
+ u8 ampdu_density;
u32 addr;
u32 val;
addr = mt7603_wtbl1_addr(idx);
+ ampdu_density = sta->ht_cap.ampdu_density;
+ if (ampdu_density < IEEE80211_HT_MPDU_DENSITY_4)
+ ampdu_density = IEEE80211_HT_MPDU_DENSITY_4;
+
val = mt76_rr(dev, addr + 2 * 4);
val &= MT_WTBL1_W2_KEY_TYPE | MT_WTBL1_W2_ADMISSION_CONTROL;
val |= FIELD_PREP(MT_WTBL1_W2_AMPDU_FACTOR, sta->ht_cap.ampdu_factor) |
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c b/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
index 8b072277ea10..a5a3bcd30d6f 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_mac.c
@@ -409,6 +409,7 @@ void mt76x02_mac_write_txwi(struct mt76x02_dev *dev, struct mt76x02_txwi *txwi,
txwi->ack_ctl |= MT_TXWI_ACK_CTL_NSEQ;
if ((info->flags & IEEE80211_TX_CTL_AMPDU) && sta) {
u8 ba_size = IEEE80211_MIN_AMPDU_BUF;
+ u8 ampdu_density = sta->ht_cap.ampdu_density;
ba_size <<= sta->ht_cap.ampdu_factor;
ba_size = min_t(int, 63, ba_size - 1);
@@ -416,9 +417,11 @@ void mt76x02_mac_write_txwi(struct mt76x02_dev *dev, struct mt76x02_txwi *txwi,
ba_size = 0;
txwi->ack_ctl |= FIELD_PREP(MT_TXWI_ACK_CTL_BA_WINDOW, ba_size);
+ if (ampdu_density < IEEE80211_HT_MPDU_DENSITY_4)
+ ampdu_density = IEEE80211_HT_MPDU_DENSITY_4;
+
txwi_flags |= MT_TXWI_FLAGS_AMPDU |
- FIELD_PREP(MT_TXWI_FLAGS_MPDU_DENSITY,
- sta->ht_cap.ampdu_density);
+ FIELD_PREP(MT_TXWI_FLAGS_MPDU_DENSITY, ampdu_density);
}
if (ieee80211_is_probe_resp(hdr->frame_control) ||
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 3/9] mt76: mt7615: use larger rx buffers if VHT is supported
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
2020-04-22 16:04 ` [PATCH 2/9] mt76: fix A-MPDU density handling Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 4/9] mt76: mt7615: never use an 802.11b CF-End rate on 5GHz Felix Fietkau
` (5 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
In VHT mode we can receive larger MPDUs. Increasing the buffer size reduces
fragmentation here, which should improve performance.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/dma.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/dma.c b/drivers/net/wireless/mediatek/mt76/mt7615/dma.c
index 5cdbe3747901..0b1fbddd1c3f 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/dma.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/dma.c
@@ -192,8 +192,13 @@ static void mt7663_dma_sched_init(struct mt7615_dev *dev)
int mt7615_dma_init(struct mt7615_dev *dev)
{
int rx_ring_size = MT7615_RX_RING_SIZE;
+ int rx_buf_size = MT_RX_BUF_SIZE;
int ret;
+ /* Increase buffer size to receive large VHT MPDUs */
+ if (dev->mt76.cap.has_5ghz)
+ rx_buf_size *= 2;
+
mt76_dma_attach(&dev->mt76);
mt76_wr(dev, MT_WPDMA_GLO_CFG,
@@ -234,7 +239,7 @@ int mt7615_dma_init(struct mt7615_dev *dev)
/* init rx queues */
ret = mt76_queue_alloc(dev, &dev->mt76.q_rx[MT_RXQ_MCU], 1,
- MT7615_RX_MCU_RING_SIZE, MT_RX_BUF_SIZE,
+ MT7615_RX_MCU_RING_SIZE, rx_buf_size,
MT_RX_RING_BASE);
if (ret)
return ret;
@@ -243,7 +248,7 @@ int mt7615_dma_init(struct mt7615_dev *dev)
rx_ring_size /= 2;
ret = mt76_queue_alloc(dev, &dev->mt76.q_rx[MT_RXQ_MAIN], 0,
- rx_ring_size, MT_RX_BUF_SIZE, MT_RX_RING_BASE);
+ rx_ring_size, rx_buf_size, MT_RX_RING_BASE);
if (ret)
return ret;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 4/9] mt76: mt7615: never use an 802.11b CF-End rate on 5GHz
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
2020-04-22 16:04 ` [PATCH 2/9] mt76: fix A-MPDU density handling Felix Fietkau
2020-04-22 16:04 ` [PATCH 3/9] mt76: mt7615: use larger rx buffers if VHT is supported Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 5/9] mt76: mt7603: " Felix Fietkau
` (4 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 396f11e1bbf6..63c7acfd4cc2 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -117,8 +117,9 @@ void mt7615_mac_set_timing(struct mt7615_phy *phy)
u32 ofdm = FIELD_PREP(MT_TIMEOUT_VAL_PLCP, 60) |
FIELD_PREP(MT_TIMEOUT_VAL_CCA, 24);
int sifs, offset;
+ bool is_5ghz = phy->mt76->chandef.chan->band == NL80211_BAND_5GHZ;
- if (phy->mt76->chandef.chan->band == NL80211_BAND_5GHZ)
+ if (is_5ghz)
sifs = 16;
else
sifs = 10;
@@ -151,7 +152,7 @@ void mt7615_mac_set_timing(struct mt7615_phy *phy)
FIELD_PREP(MT_IFS_SIFS, sifs) |
FIELD_PREP(MT_IFS_SLOT, phy->slottime));
- if (phy->slottime < 20)
+ if (phy->slottime < 20 || is_5ghz)
val = MT7615_CFEND_RATE_DEFAULT;
else
val = MT7615_CFEND_RATE_11B;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 5/9] mt76: mt7603: never use an 802.11b CF-End rate on 5GHz
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
` (2 preceding siblings ...)
2020-04-22 16:04 ` [PATCH 4/9] mt76: mt7615: never use an 802.11b CF-End rate on 5GHz Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 6/9] mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values Felix Fietkau
` (3 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
Sometimes mt7615_mac_set_timing gets called while the slot time is still
configured to 20. Ensure that in this case it always uses the OFDM CFend
rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7603/mac.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
index 73c6a3ff399c..d34828715e1c 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
@@ -51,10 +51,11 @@ void mt7603_mac_set_timing(struct mt7603_dev *dev)
int offset = 3 * dev->coverage_class;
u32 reg_offset = FIELD_PREP(MT_TIMEOUT_VAL_PLCP, offset) |
FIELD_PREP(MT_TIMEOUT_VAL_CCA, offset);
+ bool is_5ghz = dev->mphy.chandef.chan->band == NL80211_BAND_5GHZ;
int sifs;
u32 val;
- if (dev->mphy.chandef.chan->band == NL80211_BAND_5GHZ)
+ if (is_5ghz)
sifs = 16;
else
sifs = 10;
@@ -71,7 +72,7 @@ void mt7603_mac_set_timing(struct mt7603_dev *dev)
FIELD_PREP(MT_IFS_SIFS, sifs) |
FIELD_PREP(MT_IFS_SLOT, dev->slottime));
- if (dev->slottime < 20)
+ if (dev->slottime < 20 || is_5ghz)
val = MT7603_CFEND_RATE_DEFAULT;
else
val = MT7603_CFEND_RATE_11B;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 6/9] mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
` (3 preceding siblings ...)
2020-04-22 16:04 ` [PATCH 5/9] mt76: mt7603: " Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 7/9] mt76: mt7615: do not adjust MAC timings if the device is not running Felix Fietkau
` (2 subsequent siblings)
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
Slightly improves performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 63c7acfd4cc2..88cbf5ffa290 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -115,7 +115,7 @@ void mt7615_mac_set_timing(struct mt7615_phy *phy)
u32 cck = FIELD_PREP(MT_TIMEOUT_VAL_PLCP, 231) |
FIELD_PREP(MT_TIMEOUT_VAL_CCA, 48);
u32 ofdm = FIELD_PREP(MT_TIMEOUT_VAL_PLCP, 60) |
- FIELD_PREP(MT_TIMEOUT_VAL_CCA, 24);
+ FIELD_PREP(MT_TIMEOUT_VAL_CCA, 28);
int sifs, offset;
bool is_5ghz = phy->mt76->chandef.chan->band == NL80211_BAND_5GHZ;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 7/9] mt76: mt7615: do not adjust MAC timings if the device is not running
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
` (4 preceding siblings ...)
2020-04-22 16:04 ` [PATCH 6/9] mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 8/9] mt76: mt7615: fix tx status rate index calculation Felix Fietkau
2020-04-22 16:04 ` [PATCH 9/9] mt76: mt7603: " Felix Fietkau
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
Avoids register writes and MAC start/stop when the hardware isn't ready for it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 88cbf5ffa290..89aed6d67de0 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -119,6 +119,9 @@ void mt7615_mac_set_timing(struct mt7615_phy *phy)
int sifs, offset;
bool is_5ghz = phy->mt76->chandef.chan->band == NL80211_BAND_5GHZ;
+ if (!test_bit(MT76_STATE_RUNNING, &phy->mt76->state))
+ return;
+
if (is_5ghz)
sifs = 16;
else
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 8/9] mt76: mt7615: fix tx status rate index calculation
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
` (5 preceding siblings ...)
2020-04-22 16:04 ` [PATCH 7/9] mt76: mt7615: do not adjust MAC timings if the device is not running Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
2020-04-22 16:04 ` [PATCH 9/9] mt76: mt7603: " Felix Fietkau
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7615/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
index 89aed6d67de0..e7a76032caff 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mac.c
@@ -1148,7 +1148,7 @@ static bool mt7615_fill_txs(struct mt7615_dev *dev, struct mt7615_sta *sta,
if (ampdu || (info->flags & IEEE80211_TX_CTL_AMPDU))
info->flags |= IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_CTL_AMPDU;
- first_idx = max_t(int, 0, last_idx - (count + 1) / MT7615_RATE_RETRY);
+ first_idx = max_t(int, 0, last_idx - (count - 1) / MT7615_RATE_RETRY);
if (fixed_rate && !probe) {
info->status.rates[0].count = count;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH 9/9] mt76: mt7603: fix tx status rate index calculation
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
` (6 preceding siblings ...)
2020-04-22 16:04 ` [PATCH 8/9] mt76: mt7615: fix tx status rate index calculation Felix Fietkau
@ 2020-04-22 16:04 ` Felix Fietkau
7 siblings, 0 replies; 9+ messages in thread
From: Felix Fietkau @ 2020-04-22 16:04 UTC (permalink / raw)
To: linux-wireless
A switch from one rate index to the next only happens when tx count from
the current slot is greater than MT7615_RATE_RETRY, which is 1 has to be
subtracted from count, instead of added to it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
---
drivers/net/wireless/mediatek/mt76/mt7603/mac.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
index d34828715e1c..f8c0c957ca01 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7603/mac.c
@@ -1103,7 +1103,7 @@ mt7603_fill_txs(struct mt7603_dev *dev, struct mt7603_sta *sta,
if (ampdu || (info->flags & IEEE80211_TX_CTL_AMPDU))
info->flags |= IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_CTL_AMPDU;
- first_idx = max_t(int, 0, last_idx - (count + 1) / MT7603_RATE_RETRY);
+ first_idx = max_t(int, 0, last_idx - (count - 1) / MT7603_RATE_RETRY);
if (fixed_rate && !probe) {
info->status.rates[0].count = count;
--
2.24.0
^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2020-04-22 16:05 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-22 16:04 [PATCH 1/9] mt76: mt7615: fix sta ampdu factor for VHT Felix Fietkau
2020-04-22 16:04 ` [PATCH 2/9] mt76: fix A-MPDU density handling Felix Fietkau
2020-04-22 16:04 ` [PATCH 3/9] mt76: mt7615: use larger rx buffers if VHT is supported Felix Fietkau
2020-04-22 16:04 ` [PATCH 4/9] mt76: mt7615: never use an 802.11b CF-End rate on 5GHz Felix Fietkau
2020-04-22 16:04 ` [PATCH 5/9] mt76: mt7603: " Felix Fietkau
2020-04-22 16:04 ` [PATCH 6/9] mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values Felix Fietkau
2020-04-22 16:04 ` [PATCH 7/9] mt76: mt7615: do not adjust MAC timings if the device is not running Felix Fietkau
2020-04-22 16:04 ` [PATCH 8/9] mt76: mt7615: fix tx status rate index calculation Felix Fietkau
2020-04-22 16:04 ` [PATCH 9/9] mt76: mt7603: " Felix Fietkau
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).