From: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
To: ath11k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org,
Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Subject: [PATCH v5 1/8] ath11k: add 6G frequency list supported by driver
Date: Tue, 2 Jun 2020 17:17:17 -0700 [thread overview]
Message-ID: <20200603001724.12161-2-pradeepc@codeaurora.org> (raw)
In-Reply-To: <20200603001724.12161-1-pradeepc@codeaurora.org>
This patch adds support for 6GHz frequency listing.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
---
v5:
- no change
v4:
- no change
v3:
- update channel starting frequency from 5945 to 5950 as per
IEEE P802.11ax/D6.1
drivers/net/wireless/ath/ath11k/mac.c | 71 +++++++++++++++++++++++++++
1 file changed, 71 insertions(+)
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 1729e96113ef..45ffe9543c63 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -33,6 +33,15 @@
.max_power = 30, \
}
+#define CHAN6G(_channel, _freq, _flags) { \
+ .band = NL80211_BAND_6GHZ, \
+ .hw_value = (_channel), \
+ .center_freq = (_freq), \
+ .flags = (_flags), \
+ .max_antenna_gain = 0, \
+ .max_power = 30, \
+}
+
/* frame mode values are mapped as per enum ath11k_hw_txrx_mode */
static unsigned int ath11k_frame_mode = ATH11K_HW_TXRX_NATIVE_WIFI;
module_param_named(frame_mode, ath11k_frame_mode, uint, 0644);
@@ -86,6 +95,68 @@ static const struct ieee80211_channel ath11k_5ghz_channels[] = {
CHAN5G(173, 5865, 0),
};
+static const struct ieee80211_channel ath11k_6ghz_channels[] = {
+ CHAN6G(1, 5955, 0),
+ CHAN6G(5, 5975, 0),
+ CHAN6G(9, 5995, 0),
+ CHAN6G(13, 6015, 0),
+ CHAN6G(17, 6035, 0),
+ CHAN6G(21, 6055, 0),
+ CHAN6G(25, 6075, 0),
+ CHAN6G(29, 6095, 0),
+ CHAN6G(33, 6115, 0),
+ CHAN6G(37, 6135, 0),
+ CHAN6G(41, 6155, 0),
+ CHAN6G(45, 6175, 0),
+ CHAN6G(49, 6195, 0),
+ CHAN6G(53, 6215, 0),
+ CHAN6G(57, 6235, 0),
+ CHAN6G(61, 6255, 0),
+ CHAN6G(65, 6275, 0),
+ CHAN6G(69, 6295, 0),
+ CHAN6G(73, 6315, 0),
+ CHAN6G(77, 6335, 0),
+ CHAN6G(81, 6355, 0),
+ CHAN6G(85, 6375, 0),
+ CHAN6G(89, 6395, 0),
+ CHAN6G(93, 6415, 0),
+ CHAN6G(97, 6435, 0),
+ CHAN6G(101, 6455, 0),
+ CHAN6G(105, 6475, 0),
+ CHAN6G(109, 6495, 0),
+ CHAN6G(113, 6515, 0),
+ CHAN6G(117, 6535, 0),
+ CHAN6G(121, 6555, 0),
+ CHAN6G(125, 6575, 0),
+ CHAN6G(129, 6595, 0),
+ CHAN6G(133, 6615, 0),
+ CHAN6G(137, 6635, 0),
+ CHAN6G(141, 6655, 0),
+ CHAN6G(145, 6675, 0),
+ CHAN6G(149, 6695, 0),
+ CHAN6G(153, 6715, 0),
+ CHAN6G(157, 6735, 0),
+ CHAN6G(161, 6755, 0),
+ CHAN6G(165, 6775, 0),
+ CHAN6G(169, 6795, 0),
+ CHAN6G(173, 6815, 0),
+ CHAN6G(177, 6835, 0),
+ CHAN6G(181, 6855, 0),
+ CHAN6G(185, 6875, 0),
+ CHAN6G(189, 6895, 0),
+ CHAN6G(193, 6915, 0),
+ CHAN6G(197, 6935, 0),
+ CHAN6G(201, 6955, 0),
+ CHAN6G(205, 6975, 0),
+ CHAN6G(209, 6995, 0),
+ CHAN6G(213, 7015, 0),
+ CHAN6G(217, 7035, 0),
+ CHAN6G(221, 7055, 0),
+ CHAN6G(225, 7075, 0),
+ CHAN6G(229, 7095, 0),
+ CHAN6G(233, 7115, 0),
+};
+
static struct ieee80211_rate ath11k_legacy_rates[] = {
{ .bitrate = 10,
.hw_value = ATH11K_HW_RATE_CCK_LP_1M },
--
2.17.1
next prev parent reply other threads:[~2020-06-03 0:17 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-03 0:17 [PATCH v5 0/8] add 6GHz radio support in ath11k driver Pradeep Kumar Chitrapu
2020-06-03 0:17 ` Pradeep Kumar Chitrapu [this message]
2020-06-08 15:41 ` [PATCH v5 1/8] ath11k: add 6G frequency list supported by driver Kalle Valo
2020-06-11 5:06 ` Kalle Valo
2020-06-03 0:17 ` [PATCH v5 2/8] ath11k: add support for 6GHz radio in driver Pradeep Kumar Chitrapu
2020-09-15 11:16 ` Wen Gong
2020-09-15 12:32 ` Wen Gong
2020-09-15 23:07 ` Pradeep Kumar Chitrapu
2020-09-16 2:33 ` Wen Gong
2020-09-16 3:56 ` Wen Gong
2020-06-03 0:17 ` [PATCH v5 3/8] ath11k: Use freq instead of channel number in rx path Pradeep Kumar Chitrapu
2020-06-03 0:17 ` [PATCH v5 4/8] ath11k: extend peer_assoc_cmd for 6GHz band Pradeep Kumar Chitrapu
2020-06-03 0:17 ` [PATCH v5 5/8] ath11k: set psc channel flag when sending channel list to firmware Pradeep Kumar Chitrapu
2020-06-03 0:17 ` [PATCH v5 6/8] ath11k: Add 6G scan dwell time parameter in scan request command Pradeep Kumar Chitrapu
2020-06-03 0:17 ` [PATCH v5 7/8] ath11k: Send multiple scan_chan_list messages if required Pradeep Kumar Chitrapu
2020-06-09 6:37 ` Kalle Valo
2020-06-03 0:17 ` [PATCH v5 8/8] ath11k: Add support for 6g scan hint Pradeep Kumar Chitrapu
2020-08-24 3:29 ` Wen Gong
2020-09-09 8:38 ` Kalle Valo
2020-06-03 13:12 ` [PATCH v5 0/8] add 6GHz radio support in ath11k driver Kalle Valo
2020-06-03 17:50 ` Pradeep Kumar Chitrapu
2020-06-08 11:04 ` Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200603001724.12161-2-pradeepc@codeaurora.org \
--to=pradeepc@codeaurora.org \
--cc=ath11k@lists.infradead.org \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).