* [PATCH V2] b43: implement baseband init for LP-PHY <= rev1
@ 2009-08-02 23:28 Gábor Stefanik
2009-08-02 23:31 ` Gábor Stefanik
0 siblings, 1 reply; 2+ messages in thread
From: Gábor Stefanik @ 2009-08-02 23:28 UTC (permalink / raw)
To: John Linville, Michael Buesch
Cc: Larry Finger, Gábor Stefanik, Broadcom Wireless, linux-wireless
Implement baseband init for rev.0 and rev.1 LP PHYs. Convert boardflags_hi values to defines.
Implement b43_phy_copy for easier copying between registers, as needed by LP-PHY init.
Signed-off-by: Gábor Stefanik<netrolller.3d@gmail.com>
Cc: Michael Buesch<mb@bu3sch.de>
Cc: Larry Finger<larry.finger@lwfinger.net>
---
V2:
-Reversed argument order for b43_phy_copy.
-Named all registers, no more magic numbers.
-Whitespace errors hopefully fixed (I hope my mailer doesn't re-introduce them...)
b43.h | 11 ++++++
phy_common.c | 7 ++++
phy_common.h | 5 +++
phy_lp.c | 94 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
phy_lp.h | 11 +++++-
phy_n.c | 3 +
6 files changed, 127 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h
index 4e8ad84..41ca727 100644
--- a/drivers/net/wireless/b43/b43.h
+++ b/drivers/net/wireless/b43/b43.h
@@ -142,6 +142,17 @@
#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
+/* SPROM boardflags_hi values */
+#define B43_BFH_NOPA 0x0001 /* has no PA */
+#define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */
+#define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */
+#define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared
+ * with bluetooth */
+#define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */
+#define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */
+#define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna
+ * with bluetooth */
+
/* GPIO register offset, in both ChipCommon and PCI core. */
#define B43_GPIO_CONTROL 0x6c
diff --git a/drivers/net/wireless/b43/phy_common.c b/drivers/net/wireless/b43/phy_common.c
index e176b6e..1661b03 100644
--- a/drivers/net/wireless/b43/phy_common.c
+++ b/drivers/net/wireless/b43/phy_common.c
@@ -240,6 +240,13 @@ void b43_phy_write(struct b43_wldev *dev, u16 reg, u16 value)
dev->phy.ops->phy_write(dev, reg, value);
}
+void b43_phy_copy(struct b43_wldev *dev, u16 destreg, u16 srcreg)
+{
+ assert_mac_suspended(dev);
+ dev->phy.ops->phy_write(dev, destreg,
+ dev->phy.ops->phy_read(dev, srcreg));
+}
+
void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask)
{
b43_phy_write(dev, offset,
diff --git a/drivers/net/wireless/b43/phy_common.h b/drivers/net/wireless/b43/phy_common.h
index b2d9910..c7a7d6b 100644
--- a/drivers/net/wireless/b43/phy_common.h
+++ b/drivers/net/wireless/b43/phy_common.h
@@ -291,6 +291,11 @@ u16 b43_phy_read(struct b43_wldev *dev, u16 reg);
void b43_phy_write(struct b43_wldev *dev, u16 reg, u16 value);
/**
+ * b43_phy_copy - copy contents of 16bit PHY register to another
+ */
+void b43_phy_copy(struct b43_wldev *dev, u16 destreg, u16 srcreg);
+
+/**
* b43_phy_mask - Mask a PHY register with a mask
*/
void b43_phy_mask(struct b43_wldev *dev, u16 offset, u16 mask);
diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c
index 58e319d..9653b5a 100644
--- a/drivers/net/wireless/b43/phy_lp.c
+++ b/drivers/net/wireless/b43/phy_lp.c
@@ -66,7 +66,99 @@ static void lpphy_table_init(struct b43_wldev *dev)
static void lpphy_baseband_rev0_1_init(struct b43_wldev *dev)
{
- B43_WARN_ON(1);//TODO rev < 2 not supported, yet.
+ struct ssb_bus *bus = dev->dev->bus;
+ u16 tmp, tmp2;
+
+ if (dev->phy.rev == 1 &&
+ (bus->sprom.boardflags_hi & B43_BFH_FEM_BT)) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0x3F00, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0400);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_5, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_5, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_6, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_6, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_7, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_7, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_8, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_8, 0xC0FF, 0x0B00);
+ } else if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ ||
+ (bus->boardinfo.type == 0x048A) || ((dev->phy.rev == 0) &&
+ (bus->sprom.boardflags_lo & B43_BFL_FEM))) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x0001);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0400);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x0001);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0500);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0800);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0A00);
+ } else if (dev->phy.rev == 1 ||
+ (bus->sprom.boardflags_lo & B43_BFL_FEM)) {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x0004);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0800);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x0004);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0C00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0100);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0002);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0300);
+ } else {
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_1, 0xC0FF, 0x0900);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xFFC0, 0x000A);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_2, 0xC0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xFFC0, 0x0006);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_3, 0xC0FF, 0x0500);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xFFC0, 0x0006);
+ b43_phy_maskset(dev, B43_LPPHY_TR_LOOKUP_4, 0xC0FF, 0x0700);
+ }
+ if (dev->phy.rev == 1) {
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_5, B43_LPPHY_TR_LOOKUP_1);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_6, B43_LPPHY_TR_LOOKUP_2);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_7, B43_LPPHY_TR_LOOKUP_3);
+ b43_phy_copy(dev, B43_LPPHY_TR_LOOKUP_8, B43_LPPHY_TR_LOOKUP_4);
+ }
+ if ((bus->sprom.boardflags_hi & B43_BFH_FEM_BT) &&
+ (bus->chip_id == 0x5354) &&
+ (bus->chip_package == SSB_CHIPPACK_BCM4712S)) {
+ b43_phy_set(dev, B43_LPPHY_CRSGAIN_CTL, 0x0006);
+ b43_phy_write(dev, B43_LPPHY_GPIO_SELECT, 0x0005);
+ b43_phy_write(dev, B43_LPPHY_GPIO_OUTEN, 0xFFFF);
+ b43_hf_write(dev, b43_hf_read(dev) | 0x0800ULL << 32);
+ }
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
+ b43_phy_set(dev, B43_LPPHY_LP_PHY_CTL, 0x8000);
+ b43_phy_set(dev, B43_LPPHY_CRSGAIN_CTL, 0x0040);
+ b43_phy_maskset(dev, B43_LPPHY_MINPWR_LEVEL, 0x00FF, 0xA400);
+ b43_phy_maskset(dev, B43_LPPHY_CRSGAIN_CTL, 0xF0FF, 0x0B00);
+ b43_phy_maskset(dev, B43_LPPHY_SYNCPEAKCNT, 0xFFF8, 0x0007);
+ b43_phy_maskset(dev, B43_LPPHY_DSSS_CONFIRM_CNT, 0xFFF8, 0x0003);
+ b43_phy_maskset(dev, B43_LPPHY_DSSS_CONFIRM_CNT, 0xFFC7, 0x0020);
+ b43_phy_mask(dev, B43_LPPHY_IDLEAFTERPKTRXTO, 0x00FF);
+ } else { /* 5GHz */
+ b43_phy_mask(dev, B43_LPPHY_LP_PHY_CTL, 0x7FFF);
+ b43_phy_mask(dev, B43_LPPHY_CRSGAIN_CTL, 0xFFBF);
+ }
+ if (dev->phy.rev == 1) {
+ tmp = b43_phy_read(dev, B43_LPPHY_CLIPCTRTHRESH);
+ tmp2 = (tmp & 0x03E0) >> 5;
+ tmp2 |= tmp << 5;
+ b43_phy_write(dev, B43_LPPHY_4C3, tmp2);
+ tmp = b43_phy_read(dev, B43_LPPHY_OFDMSYNCTHRESH0);
+ tmp2 = (tmp & 0x1F00) >> 8;
+ tmp2 |= tmp << 5;
+ b43_phy_write(dev, B43_LPPHY_4C4, tmp2);
+ tmp = b43_phy_read(dev, B43_LPPHY_VERYLOWGAINDB);
+ tmp2 = tmp & 0x00FF;
+ tmp2 |= tmp << 8;
+ b43_phy_write(dev, B43_LPPHY_4C5, tmp2);
+ }
}
static void lpphy_baseband_rev2plus_init(struct b43_wldev *dev)
diff --git a/drivers/net/wireless/b43/phy_lp.h b/drivers/net/wireless/b43/phy_lp.h
index 18370b4..829b2bb 100644
--- a/drivers/net/wireless/b43/phy_lp.h
+++ b/drivers/net/wireless/b43/phy_lp.h
@@ -273,12 +273,19 @@
#define B43_LPPHY_AFE_DDFS_POINTER_INIT B43_PHY_OFDM(0xB8) /* AFE DDFS pointer init */
#define B43_LPPHY_AFE_DDFS_INCR_INIT B43_PHY_OFDM(0xB9) /* AFE DDFS incr init */
#define B43_LPPHY_MRCNOISEREDUCTION B43_PHY_OFDM(0xBA) /* mrcNoiseReduction */
-#define B43_LPPHY_TRLOOKUP3 B43_PHY_OFDM(0xBB) /* TRLookup3 */
-#define B43_LPPHY_TRLOOKUP4 B43_PHY_OFDM(0xBC) /* TRLookup4 */
+#define B43_LPPHY_TR_LOOKUP_3 B43_PHY_OFDM(0xBB) /* TR Lookup 3 */
+#define B43_LPPHY_TR_LOOKUP_4 B43_PHY_OFDM(0xBC) /* TR Lookup 4 */
#define B43_LPPHY_RADAR_FIFO_STAT B43_PHY_OFDM(0xBD) /* Radar FIFO Status */
#define B43_LPPHY_GPIO_OUTEN B43_PHY_OFDM(0xBE) /* GPIO Out enable */
#define B43_LPPHY_GPIO_SELECT B43_PHY_OFDM(0xBF) /* GPIO Select */
#define B43_LPPHY_GPIO_OUT B43_PHY_OFDM(0xC0) /* GPIO Out */
+#define B43_LPPHY_4C3 B43_PHY_OFDM(0xC3) /* unknown, used during BB init */
+#define B43_LPPHY_4C4 B43_PHY_OFDM(0xC4) /* unknown, used during BB init */
+#define B43_LPPHY_4C5 B43_PHY_OFDM(0xC5) /* unknown, used during BB init */
+#define B43_LPPHY_TR_LOOKUP_5 B43_PHY_OFDM(0xC7) /* TR Lookup 5 */
+#define B43_LPPHY_TR_LOOKUP_6 B43_PHY_OFDM(0xC8) /* TR Lookup 6 */
+#define B43_LPPHY_TR_LOOKUP_7 B43_PHY_OFDM(0xC9) /* TR Lookup 7 */
+#define B43_LPPHY_TR_LOOKUP_8 B43_PHY_OFDM(0xCA) /* TR Lookup 8 */
diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c
index 8bcfda5..14ad95a 100644
--- a/drivers/net/wireless/b43/phy_n.c
+++ b/drivers/net/wireless/b43/phy_n.c
@@ -137,7 +137,8 @@ static void b43_radio_init2055_post(struct b43_wldev *dev)
b43_radio_mask(dev, B2055_MASTER1, 0xFFF3);
msleep(1);
- if ((sprom->revision != 4) || !(sprom->boardflags_hi & 0x0002)) {
+ if ((sprom->revision != 4) ||
+ !(sprom->boardflags_hi & B43_BFH_RSSIINV)) {
if ((binfo->vendor != PCI_VENDOR_ID_BROADCOM) ||
(binfo->type != 0x46D) ||
(binfo->rev < 0x41)) {
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH V2] b43: implement baseband init for LP-PHY <= rev1
2009-08-02 23:28 [PATCH V2] b43: implement baseband init for LP-PHY <= rev1 Gábor Stefanik
@ 2009-08-02 23:31 ` Gábor Stefanik
0 siblings, 0 replies; 2+ messages in thread
From: Gábor Stefanik @ 2009-08-02 23:31 UTC (permalink / raw)
To: John Linville, Michael Buesch
Cc: Larry Finger, Gábor Stefanik, Broadcom Wireless, linux-wireless
On Mon, Aug 3, 2009 at 1:28 AM, Gábor Stefanik<netrolller.3d@gmail.com> wrote:
> Implement baseband init for rev.0 and rev.1 LP PHYs. Convert boardflags_hi
> values to defines.
> Implement b43_phy_copy for easier copying between registers, as needed by
> LP-PHY init.
>
> Signed-off-by: Gábor Stefanik<netrolller.3d@gmail.com>
> Cc: Michael Buesch<mb@bu3sch.de>
> Cc: Larry Finger<larry.finger@lwfinger.net>
> ---
> V2:
> -Reversed argument order for b43_phy_copy.
> -Named all registers, no more magic numbers.
> -Whitespace errors hopefully fixed (I hope my mailer doesn't re-introduce
> them...)
Phew! No more whitespace corruption, it seems... looks like
Thunderbird doesn't like the Linux coding style. :-)
--
Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2009-08-02 23:31 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-08-02 23:28 [PATCH V2] b43: implement baseband init for LP-PHY <= rev1 Gábor Stefanik
2009-08-02 23:31 ` Gábor Stefanik
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).