* [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x
@ 2013-10-03 3:44 Prabhakar Kushwaha
2013-10-21 3:37 ` Prabhakar Kushwaha
0 siblings, 1 reply; 4+ messages in thread
From: Prabhakar Kushwaha @ 2013-10-03 3:44 UTC (permalink / raw)
To: linuxppc-dev
Cc: Poonam Aggrwal, Priyanka Jain, scottwood, Varun Sethi,
Prabhakar Kushwaha
The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
processor cores with high-performance data path acceleration architecture
and network peripheral interfaces required for networking & telecommunications.
T1042 personality is a reduced personality of T1040 without Integrated 8-port
Gigabit Ethernet switch.
The T1040/T1042 SoC includes the following function and features:
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration (SEC 5.0)
- RegEx Pattern Matching Acceleration (PME 2.2)
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch (T1040 only)
- Four 1 Gbps Ethernet controllers
- Two RGMII interfaces or one RGMII and one MII interfaces
- High speed peripheral interfaces
- Four PCI Express 2.0 controllers running at up to 5 GHz
- Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
- Upto two QSGMII interface
- Upto six SGMII interface supporting 1000 Mbps
- One SGMII interface supporting upto 2500 Mbps
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
- eSPI controller
- Four I2C controllers
- Four UARTs
- Four GPIO controllers
- Integrated flash controller (IFC)
- Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
- TDM interface
- Multicore programmable interrupt controller (PIC)
- Two 8-channel DMA engines
- Single source clocking implementation
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
---
Based upon git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git
Branch merge
Changes for v2: Incorporated Scott's comments
- Update t1040si-post.dtsi
- update clock device tree node as per
http://patchwork.ozlabs.org/patch/274134/
- removed DMA node, It will be added later as per
http://patchwork.ozlabs.org/patch/271238/
- Updated display compatible field
Changes for v3: Incorporated Scott's comments
- Updated soc compatible field
- updated clock compatible field
Changes for v4: Sending as it is
Changes for v5: Sending as it is
Changes for v6: Updated branch of creation
Changes for v7: Incororated Scott's commetns
- Create patch set
- remove whitespace
- Removed l2switch. It will be added later
Changes for v8: Incorporated Scott's comments
- Added comment line in T1042si-post.dtsi
- removed extra lines
arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 418 +++++++++++++++++++++++++++
arch/powerpc/boot/dts/fsl/t1042si-post.dtsi | 37 +++
arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi | 106 +++++++
3 files changed, 561 insertions(+)
create mode 100644 arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
create mode 100644 arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
new file mode 100644
index 0000000..9bf1c30
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
@@ -0,0 +1,418 @@
+/*
+ * T1040 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+&ifc {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "fsl,ifc", "simple-bus";
+ interrupts = <25 2 0 0>;
+};
+
+&pci0 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <20 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <20 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 40 1 0 0
+ 0000 0 0 2 &mpic 1 1 0 0
+ 0000 0 0 3 &mpic 2 1 0 0
+ 0000 0 0 4 &mpic 3 1 0 0
+ >;
+ };
+};
+
+&pci1 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0 0xff>;
+ interrupts = <21 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <21 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 41 1 0 0
+ 0000 0 0 2 &mpic 5 1 0 0
+ 0000 0 0 3 &mpic 6 1 0 0
+ 0000 0 0 4 &mpic 7 1 0 0
+ >;
+ };
+};
+
+&pci2 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <22 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <22 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 42 1 0 0
+ 0000 0 0 2 &mpic 9 1 0 0
+ 0000 0 0 3 &mpic 10 1 0 0
+ 0000 0 0 4 &mpic 11 1 0 0
+ >;
+ };
+};
+
+&pci3 {
+ compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
+ device_type = "pci";
+ #size-cells = <2>;
+ #address-cells = <3>;
+ bus-range = <0x0 0xff>;
+ interrupts = <23 2 0 0>;
+ fsl,iommu-parent = <&pamu0>;
+ pcie@0 {
+ reg = <0 0 0 0 0>;
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ interrupts = <23 2 0 0>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <
+ /* IDSEL 0x0 */
+ 0000 0 0 1 &mpic 43 1 0 0
+ 0000 0 0 2 &mpic 0 1 0 0
+ 0000 0 0 3 &mpic 4 1 0 0
+ 0000 0 0 4 &mpic 8 1 0 0
+ >;
+ };
+};
+
+&dcsr {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,dcsr", "simple-bus";
+
+ dcsr-epu@0 {
+ compatible = "fsl,t1040-dcsr-epu", "fsl,dcsr-epu";
+ interrupts = <52 2 0 0
+ 84 2 0 0
+ 85 2 0 0>;
+ reg = <0x0 0x1000>;
+ };
+ dcsr-npc {
+ compatible = "fsl,t1040-dcsr-cnpc", "fsl,dcsr-cnpc";
+ reg = <0x1000 0x1000 0x1002000 0x10000>;
+ };
+ dcsr-nxc@2000 {
+ compatible = "fsl,dcsr-nxc";
+ reg = <0x2000 0x1000>;
+ };
+ dcsr-corenet {
+ compatible = "fsl,dcsr-corenet";
+ reg = <0x8000 0x1000 0x1A000 0x1000>;
+ };
+ dcsr-dpaa@9000 {
+ compatible = "fsl,t1040-dcsr-dpaa", "fsl,dcsr-dpaa";
+ reg = <0x9000 0x1000>;
+ };
+ dcsr-ocn@11000 {
+ compatible = "fsl,t1040-dcsr-ocn", "fsl,dcsr-ocn";
+ reg = <0x11000 0x1000>;
+ };
+ dcsr-ddr@12000 {
+ compatible = "fsl,dcsr-ddr";
+ dev-handle = <&ddr1>;
+ reg = <0x12000 0x1000>;
+ };
+ dcsr-nal@18000 {
+ compatible = "fsl,t1040-dcsr-nal", "fsl,dcsr-nal";
+ reg = <0x18000 0x1000>;
+ };
+ dcsr-rcpm@22000 {
+ compatible = "fsl,t1040-dcsr-rcpm", "fsl,dcsr-rcpm";
+ reg = <0x22000 0x1000>;
+ };
+ dcsr-snpc@30000 {
+ compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x30000 0x1000 0x1022000 0x10000>;
+ };
+ dcsr-snpc@31000 {
+ compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
+ reg = <0x31000 0x1000 0x1042000 0x10000>;
+ };
+ dcsr-cpu-sb-proxy@100000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu0>;
+ reg = <0x100000 0x1000 0x101000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@108000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu1>;
+ reg = <0x108000 0x1000 0x109000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@110000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu2>;
+ reg = <0x110000 0x1000 0x111000 0x1000>;
+ };
+ dcsr-cpu-sb-proxy@118000 {
+ compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
+ cpu-handle = <&cpu3>;
+ reg = <0x118000 0x1000 0x119000 0x1000>;
+ };
+};
+
+&soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ device_type = "soc";
+ compatible = "simple-bus";
+
+ soc-sram-error {
+ compatible = "fsl,soc-sram-error";
+ interrupts = <16 2 1 29>;
+ };
+
+ corenet-law@0 {
+ compatible = "fsl,corenet-law";
+ reg = <0x0 0x1000>;
+ fsl,num-laws = <16>;
+ };
+
+ ddr1: memory-controller@8000 {
+ compatible = "fsl,qoriq-memory-controller-v5.0",
+ "fsl,qoriq-memory-controller";
+ reg = <0x8000 0x1000>;
+ interrupts = <16 2 1 23>;
+ };
+
+ cpc: l3-cache-controller@10000 {
+ compatible = "fsl,t1040-l3-cache-controller", "cache";
+ reg = <0x10000 0x1000>;
+ interrupts = <16 2 1 27>;
+ };
+
+ corenet-cf@18000 {
+ compatible = "fsl,corenet2-cf";
+ reg = <0x18000 0x1000>;
+ interrupts = <16 2 1 31>;
+ fsl,ccf-num-csdids = <32>;
+ fsl,ccf-num-snoopids = <32>;
+ };
+
+ iommu@20000 {
+ compatible = "fsl,pamu-v1.0", "fsl,pamu";
+ reg = <0x20000 0x1000>;
+ ranges = <0 0x20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <
+ 24 2 0 0
+ 16 2 1 30>;
+ pamu0: pamu@0 {
+ reg = <0 0x1000>;
+ fsl,primary-cache-geometry = <128 1>;
+ fsl,secondary-cache-geometry = <16 2>;
+ };
+ };
+
+/include/ "qoriq-mpic.dtsi"
+
+ guts: global-utilities@e0000 {
+ compatible = "fsl,t1040-device-config", "fsl,qoriq-device-config-2.0";
+ reg = <0xe0000 0xe00>;
+ fsl,has-rstcr;
+ fsl,liodn-bits = <12>;
+ };
+
+ clockgen: global-utilities@e1000 {
+ compatible = "fsl,t1040-clockgen", "fsl,qoriq-clockgen-2.0",
+ "fixed-clock";
+ reg = <0xe1000 0x1000>;
+ clock-output-names = "sysclk";
+ #clock-cells = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pll0: pll0@800 {
+ #clock-cells = <1>;
+ reg = <0x800 4>;
+ compatible = "fsl,qoriq-core-pll-2.0";
+ clocks = <&clockgen>;
+ clock-output-names = "pll0", "pll0-div2", "pll0-div4";
+ };
+ pll1: pll1@820 {
+ #clock-cells = <1>;
+ reg = <0x820 4>;
+ compatible = "fsl,qoriq-core-pll-2.0";
+ clocks = <&clockgen>;
+ clock-output-names = "pll1", "pll1-div2", "pll1-div4";
+ };
+ mux0: mux0@0 {
+ #clock-cells = <0>;
+ reg = <0x0 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux0";
+ };
+ mux1: mux1@20 {
+ #clock-cells = <0>;
+ reg = <0x20 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux1";
+ };
+ mux2: mux2@40 {
+ #clock-cells = <0>;
+ reg = <0x40 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux2";
+ };
+ mux3: mux3@60 {
+ #clock-cells = <0>;
+ reg = <0x60 4>;
+ compatible = "fsl,core-mux-clock";
+ clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
+ <&pll1 0>, <&pll1 1>, <&pll1 2>;
+ clock-names = "pll0_0", "pll0_1", "pll0_2",
+ "pll1_0", "pll1_1", "pll1_2";
+ clock-output-names = "cmux3";
+ };
+ };
+
+ rcpm: global-utilities@e2000 {
+ compatible = "fsl,t1040-rcpm", "fsl,qoriq-rcpm-2.0";
+ reg = <0xe2000 0x1000>;
+ };
+
+ sfp: sfp@e8000 {
+ compatible = "fsl,t1040-sfp";
+ reg = <0xe8000 0x1000>;
+ };
+
+ serdes: serdes@ea000 {
+ compatible = "fsl,t1040-serdes";
+ reg = <0xea000 0x4000>;
+ };
+
+/include/ "qoriq-espi-0.dtsi"
+ spi@110000 {
+ fsl,espi-num-chipselects = <4>;
+ };
+
+/include/ "qoriq-esdhc-0.dtsi"
+ sdhc@114000 {
+ compatible = "fsl,t1040-esdhc", "fsl,esdhc";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
+ sdhci,auto-cmd12;
+ };
+/include/ "qoriq-i2c-0.dtsi"
+/include/ "qoriq-i2c-1.dtsi"
+/include/ "qoriq-duart-0.dtsi"
+/include/ "qoriq-duart-1.dtsi"
+/include/ "qoriq-gpio-0.dtsi"
+/include/ "qoriq-gpio-1.dtsi"
+/include/ "qoriq-gpio-2.dtsi"
+/include/ "qoriq-gpio-3.dtsi"
+/include/ "qoriq-usb2-mph-0.dtsi"
+ usb0: usb@210000 {
+ compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
+ phy_type = "utmi";
+ port0;
+ };
+/include/ "qoriq-usb2-dr-0.dtsi"
+ usb1: usb@211000 {
+ compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
+ dr_mode = "host";
+ phy_type = "utmi";
+ };
+
+ display@180000 {
+ compatible = "fsl,t1040-diu", "fsl,diu";
+ reg = <0x180000 1000>;
+ interrupts = <74 2 0 0>;
+ };
+
+/include/ "qoriq-sata2-0.dtsi"
+sata@220000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
+};
+/include/ "qoriq-sata2-1.dtsi"
+sata@221000 {
+ fsl,iommu-parent = <&pamu0>;
+ fsl,liodn-reg = <&guts 0x554>; /* SATA2LIODNR */
+};
+/include/ "qoriq-sec5.0-0.dtsi"
+};
diff --git a/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
new file mode 100644
index 0000000..319b74f
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
@@ -0,0 +1,37 @@
+/*
+ * T1042 Silicon/SoC Device Tree Source (post include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/include/ "t1040si-post.dtsi"
+
+/* Place holder for ethernet related device tree nodes */
diff --git a/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
new file mode 100644
index 0000000..c0ae954
--- /dev/null
+++ b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
@@ -0,0 +1,106 @@
+/*
+ * T1040/T1042 Silicon/SoC Device Tree Source (pre include)
+ *
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * * Neither the name of Freescale Semiconductor nor the
+ * names of its contributors may be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ *
+ *
+ * ALTERNATIVELY, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") as published by the Free Software
+ * Foundation, either version 2 of that License or (at your option) any
+ * later version.
+ *
+ * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
+ * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
+ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/dts-v1/;
+
+/include/ "e5500_power_isa.dtsi"
+
+/ {
+ compatible = "fsl,T104x";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&mpic>;
+
+ aliases {
+ ccsr = &soc;
+ dcsr = &dcsr;
+
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ pci3 = &pci3;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ sdhc = &sdhc;
+
+ crypto = &crypto;
+
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: PowerPC,e5500@0 {
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&mux0>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu1: PowerPC,e5500@1 {
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&mux1>;
+ next-level-cache = <&L2_2>;
+ L2_2: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu2: PowerPC,e5500@2 {
+ device_type = "cpu";
+ reg = <2>;
+ clocks = <&mux2>;
+ next-level-cache = <&L2_3>;
+ L2_3: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ cpu3: PowerPC,e5500@3 {
+ device_type = "cpu";
+ reg = <3>;
+ clocks = <&mux3>;
+ next-level-cache = <&L2_4>;
+ L2_4: l2-cache {
+ next-level-cache = <&cpc>;
+ };
+ };
+ };
+};
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x
2013-10-03 3:44 [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x Prabhakar Kushwaha
@ 2013-10-21 3:37 ` Prabhakar Kushwaha
2013-10-29 1:11 ` Scott Wood
0 siblings, 1 reply; 4+ messages in thread
From: Prabhakar Kushwaha @ 2013-10-21 3:37 UTC (permalink / raw)
To: Prabhakar Kushwaha, linuxppc-dev
Cc: scottwood, Varun Sethi, Poonam Aggrwal, Priyanka Jain
Hi Ben,
This patch is present in upstream review list from a long time.
There are no review comments.
So, I request you to pick this patch-set for powerpc.git repository.
http://patchwork.ozlabs.org/patch/280207/
http://patchwork.ozlabs.org/patch/280208/
Regards,
Prabhakar
On 10/03/2013 09:14 AM, Prabhakar Kushwaha wrote:
> The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA
> processor cores with high-performance data path acceleration architecture
> and network peripheral interfaces required for networking & telecommunications.
>
> T1042 personality is a reduced personality of T1040 without Integrated 8-port
> Gigabit Ethernet switch.
>
> The T1040/T1042 SoC includes the following function and features:
>
> - Four e5500 cores, each with a private 256 KB L2 cache
> - 256 KB shared L3 CoreNet platform cache (CPC)
> - Interconnect CoreNet platform
> - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
> support
> - Data Path Acceleration Architecture (DPAA) incorporating acceleration
> for the following functions:
> - Packet parsing, classification, and distribution
> - Queue management for scheduling, packet sequencing, and congestion
> management
> - Cryptography Acceleration (SEC 5.0)
> - RegEx Pattern Matching Acceleration (PME 2.2)
> - IEEE Std 1588 support
> - Hardware buffer management for buffer allocation and deallocation
> - Ethernet interfaces
> - Integrated 8-port Gigabit Ethernet switch (T1040 only)
> - Four 1 Gbps Ethernet controllers
> - Two RGMII interfaces or one RGMII and one MII interfaces
> - High speed peripheral interfaces
> - Four PCI Express 2.0 controllers running at up to 5 GHz
> - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation
> - Upto two QSGMII interface
> - Upto six SGMII interface supporting 1000 Mbps
> - One SGMII interface supporting upto 2500 Mbps
> - Additional peripheral interfaces
> - Two USB 2.0 controllers with integrated PHY
> - SD/eSDHC/eMMC
> - eSPI controller
> - Four I2C controllers
> - Four UARTs
> - Four GPIO controllers
> - Integrated flash controller (IFC)
> - Change this to LCD/ HDMI interface (DIU) with 12 bit dual data rate
> - TDM interface
> - Multicore programmable interrupt controller (PIC)
> - Two 8-channel DMA engines
> - Single source clocking implementation
> - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
>
> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
> Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
> ---
> Based upon git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc.git
> Branch merge
>
> Changes for v2: Incorporated Scott's comments
> - Update t1040si-post.dtsi
> - update clock device tree node as per
> http://patchwork.ozlabs.org/patch/274134/
> - removed DMA node, It will be added later as per
> http://patchwork.ozlabs.org/patch/271238/
> - Updated display compatible field
>
> Changes for v3: Incorporated Scott's comments
> - Updated soc compatible field
> - updated clock compatible field
>
> Changes for v4: Sending as it is
> Changes for v5: Sending as it is
> Changes for v6: Updated branch of creation
> Changes for v7: Incororated Scott's commetns
> - Create patch set
> - remove whitespace
> - Removed l2switch. It will be added later
> Changes for v8: Incorporated Scott's comments
> - Added comment line in T1042si-post.dtsi
> - removed extra lines
>
> arch/powerpc/boot/dts/fsl/t1040si-post.dtsi | 418 +++++++++++++++++++++++++++
> arch/powerpc/boot/dts/fsl/t1042si-post.dtsi | 37 +++
> arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi | 106 +++++++
> 3 files changed, 561 insertions(+)
> create mode 100644 arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> create mode 100644 arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
> create mode 100644 arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
>
> diff --git a/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> new file mode 100644
> index 0000000..9bf1c30
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/fsl/t1040si-post.dtsi
> @@ -0,0 +1,418 @@
> +/*
> + * T1040 Silicon/SoC Device Tree Source (post include)
> + *
> + * Copyright 2013 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +&ifc {
> + #address-cells = <2>;
> + #size-cells = <1>;
> + compatible = "fsl,ifc", "simple-bus";
> + interrupts = <25 2 0 0>;
> +};
> +
> +&pci0 {
> + compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
> + device_type = "pci";
> + #size-cells = <2>;
> + #address-cells = <3>;
> + bus-range = <0x0 0xff>;
> + interrupts = <20 2 0 0>;
> + fsl,iommu-parent = <&pamu0>;
> + pcie@0 {
> + reg = <0 0 0 0 0>;
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + #address-cells = <3>;
> + device_type = "pci";
> + interrupts = <20 2 0 0>;
> + interrupt-map-mask = <0xf800 0 0 7>;
> + interrupt-map = <
> + /* IDSEL 0x0 */
> + 0000 0 0 1 &mpic 40 1 0 0
> + 0000 0 0 2 &mpic 1 1 0 0
> + 0000 0 0 3 &mpic 2 1 0 0
> + 0000 0 0 4 &mpic 3 1 0 0
> + >;
> + };
> +};
> +
> +&pci1 {
> + compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
> + device_type = "pci";
> + #size-cells = <2>;
> + #address-cells = <3>;
> + bus-range = <0 0xff>;
> + interrupts = <21 2 0 0>;
> + fsl,iommu-parent = <&pamu0>;
> + pcie@0 {
> + reg = <0 0 0 0 0>;
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + #address-cells = <3>;
> + device_type = "pci";
> + interrupts = <21 2 0 0>;
> + interrupt-map-mask = <0xf800 0 0 7>;
> + interrupt-map = <
> + /* IDSEL 0x0 */
> + 0000 0 0 1 &mpic 41 1 0 0
> + 0000 0 0 2 &mpic 5 1 0 0
> + 0000 0 0 3 &mpic 6 1 0 0
> + 0000 0 0 4 &mpic 7 1 0 0
> + >;
> + };
> +};
> +
> +&pci2 {
> + compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
> + device_type = "pci";
> + #size-cells = <2>;
> + #address-cells = <3>;
> + bus-range = <0x0 0xff>;
> + interrupts = <22 2 0 0>;
> + fsl,iommu-parent = <&pamu0>;
> + pcie@0 {
> + reg = <0 0 0 0 0>;
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + #address-cells = <3>;
> + device_type = "pci";
> + interrupts = <22 2 0 0>;
> + interrupt-map-mask = <0xf800 0 0 7>;
> + interrupt-map = <
> + /* IDSEL 0x0 */
> + 0000 0 0 1 &mpic 42 1 0 0
> + 0000 0 0 2 &mpic 9 1 0 0
> + 0000 0 0 3 &mpic 10 1 0 0
> + 0000 0 0 4 &mpic 11 1 0 0
> + >;
> + };
> +};
> +
> +&pci3 {
> + compatible = "fsl,t1040-pcie", "fsl,qoriq-pcie-v2.4", "fsl,qoriq-pcie";
> + device_type = "pci";
> + #size-cells = <2>;
> + #address-cells = <3>;
> + bus-range = <0x0 0xff>;
> + interrupts = <23 2 0 0>;
> + fsl,iommu-parent = <&pamu0>;
> + pcie@0 {
> + reg = <0 0 0 0 0>;
> + #interrupt-cells = <1>;
> + #size-cells = <2>;
> + #address-cells = <3>;
> + device_type = "pci";
> + interrupts = <23 2 0 0>;
> + interrupt-map-mask = <0xf800 0 0 7>;
> + interrupt-map = <
> + /* IDSEL 0x0 */
> + 0000 0 0 1 &mpic 43 1 0 0
> + 0000 0 0 2 &mpic 0 1 0 0
> + 0000 0 0 3 &mpic 4 1 0 0
> + 0000 0 0 4 &mpic 8 1 0 0
> + >;
> + };
> +};
> +
> +&dcsr {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "fsl,dcsr", "simple-bus";
> +
> + dcsr-epu@0 {
> + compatible = "fsl,t1040-dcsr-epu", "fsl,dcsr-epu";
> + interrupts = <52 2 0 0
> + 84 2 0 0
> + 85 2 0 0>;
> + reg = <0x0 0x1000>;
> + };
> + dcsr-npc {
> + compatible = "fsl,t1040-dcsr-cnpc", "fsl,dcsr-cnpc";
> + reg = <0x1000 0x1000 0x1002000 0x10000>;
> + };
> + dcsr-nxc@2000 {
> + compatible = "fsl,dcsr-nxc";
> + reg = <0x2000 0x1000>;
> + };
> + dcsr-corenet {
> + compatible = "fsl,dcsr-corenet";
> + reg = <0x8000 0x1000 0x1A000 0x1000>;
> + };
> + dcsr-dpaa@9000 {
> + compatible = "fsl,t1040-dcsr-dpaa", "fsl,dcsr-dpaa";
> + reg = <0x9000 0x1000>;
> + };
> + dcsr-ocn@11000 {
> + compatible = "fsl,t1040-dcsr-ocn", "fsl,dcsr-ocn";
> + reg = <0x11000 0x1000>;
> + };
> + dcsr-ddr@12000 {
> + compatible = "fsl,dcsr-ddr";
> + dev-handle = <&ddr1>;
> + reg = <0x12000 0x1000>;
> + };
> + dcsr-nal@18000 {
> + compatible = "fsl,t1040-dcsr-nal", "fsl,dcsr-nal";
> + reg = <0x18000 0x1000>;
> + };
> + dcsr-rcpm@22000 {
> + compatible = "fsl,t1040-dcsr-rcpm", "fsl,dcsr-rcpm";
> + reg = <0x22000 0x1000>;
> + };
> + dcsr-snpc@30000 {
> + compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
> + reg = <0x30000 0x1000 0x1022000 0x10000>;
> + };
> + dcsr-snpc@31000 {
> + compatible = "fsl,t1040-dcsr-snpc", "fsl,dcsr-snpc";
> + reg = <0x31000 0x1000 0x1042000 0x10000>;
> + };
> + dcsr-cpu-sb-proxy@100000 {
> + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
> + cpu-handle = <&cpu0>;
> + reg = <0x100000 0x1000 0x101000 0x1000>;
> + };
> + dcsr-cpu-sb-proxy@108000 {
> + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
> + cpu-handle = <&cpu1>;
> + reg = <0x108000 0x1000 0x109000 0x1000>;
> + };
> + dcsr-cpu-sb-proxy@110000 {
> + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
> + cpu-handle = <&cpu2>;
> + reg = <0x110000 0x1000 0x111000 0x1000>;
> + };
> + dcsr-cpu-sb-proxy@118000 {
> + compatible = "fsl,dcsr-e5500-sb-proxy", "fsl,dcsr-cpu-sb-proxy";
> + cpu-handle = <&cpu3>;
> + reg = <0x118000 0x1000 0x119000 0x1000>;
> + };
> +};
> +
> +&soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + device_type = "soc";
> + compatible = "simple-bus";
> +
> + soc-sram-error {
> + compatible = "fsl,soc-sram-error";
> + interrupts = <16 2 1 29>;
> + };
> +
> + corenet-law@0 {
> + compatible = "fsl,corenet-law";
> + reg = <0x0 0x1000>;
> + fsl,num-laws = <16>;
> + };
> +
> + ddr1: memory-controller@8000 {
> + compatible = "fsl,qoriq-memory-controller-v5.0",
> + "fsl,qoriq-memory-controller";
> + reg = <0x8000 0x1000>;
> + interrupts = <16 2 1 23>;
> + };
> +
> + cpc: l3-cache-controller@10000 {
> + compatible = "fsl,t1040-l3-cache-controller", "cache";
> + reg = <0x10000 0x1000>;
> + interrupts = <16 2 1 27>;
> + };
> +
> + corenet-cf@18000 {
> + compatible = "fsl,corenet2-cf";
> + reg = <0x18000 0x1000>;
> + interrupts = <16 2 1 31>;
> + fsl,ccf-num-csdids = <32>;
> + fsl,ccf-num-snoopids = <32>;
> + };
> +
> + iommu@20000 {
> + compatible = "fsl,pamu-v1.0", "fsl,pamu";
> + reg = <0x20000 0x1000>;
> + ranges = <0 0x20000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + interrupts = <
> + 24 2 0 0
> + 16 2 1 30>;
> + pamu0: pamu@0 {
> + reg = <0 0x1000>;
> + fsl,primary-cache-geometry = <128 1>;
> + fsl,secondary-cache-geometry = <16 2>;
> + };
> + };
> +
> +/include/ "qoriq-mpic.dtsi"
> +
> + guts: global-utilities@e0000 {
> + compatible = "fsl,t1040-device-config", "fsl,qoriq-device-config-2.0";
> + reg = <0xe0000 0xe00>;
> + fsl,has-rstcr;
> + fsl,liodn-bits = <12>;
> + };
> +
> + clockgen: global-utilities@e1000 {
> + compatible = "fsl,t1040-clockgen", "fsl,qoriq-clockgen-2.0",
> + "fixed-clock";
> + reg = <0xe1000 0x1000>;
> + clock-output-names = "sysclk";
> + #clock-cells = <0>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + pll0: pll0@800 {
> + #clock-cells = <1>;
> + reg = <0x800 4>;
> + compatible = "fsl,qoriq-core-pll-2.0";
> + clocks = <&clockgen>;
> + clock-output-names = "pll0", "pll0-div2", "pll0-div4";
> + };
> + pll1: pll1@820 {
> + #clock-cells = <1>;
> + reg = <0x820 4>;
> + compatible = "fsl,qoriq-core-pll-2.0";
> + clocks = <&clockgen>;
> + clock-output-names = "pll1", "pll1-div2", "pll1-div4";
> + };
> + mux0: mux0@0 {
> + #clock-cells = <0>;
> + reg = <0x0 4>;
> + compatible = "fsl,core-mux-clock";
> + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
> + <&pll1 0>, <&pll1 1>, <&pll1 2>;
> + clock-names = "pll0_0", "pll0_1", "pll0_2",
> + "pll1_0", "pll1_1", "pll1_2";
> + clock-output-names = "cmux0";
> + };
> + mux1: mux1@20 {
> + #clock-cells = <0>;
> + reg = <0x20 4>;
> + compatible = "fsl,core-mux-clock";
> + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
> + <&pll1 0>, <&pll1 1>, <&pll1 2>;
> + clock-names = "pll0_0", "pll0_1", "pll0_2",
> + "pll1_0", "pll1_1", "pll1_2";
> + clock-output-names = "cmux1";
> + };
> + mux2: mux2@40 {
> + #clock-cells = <0>;
> + reg = <0x40 4>;
> + compatible = "fsl,core-mux-clock";
> + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
> + <&pll1 0>, <&pll1 1>, <&pll1 2>;
> + clock-names = "pll0_0", "pll0_1", "pll0_2",
> + "pll1_0", "pll1_1", "pll1_2";
> + clock-output-names = "cmux2";
> + };
> + mux3: mux3@60 {
> + #clock-cells = <0>;
> + reg = <0x60 4>;
> + compatible = "fsl,core-mux-clock";
> + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
> + <&pll1 0>, <&pll1 1>, <&pll1 2>;
> + clock-names = "pll0_0", "pll0_1", "pll0_2",
> + "pll1_0", "pll1_1", "pll1_2";
> + clock-output-names = "cmux3";
> + };
> + };
> +
> + rcpm: global-utilities@e2000 {
> + compatible = "fsl,t1040-rcpm", "fsl,qoriq-rcpm-2.0";
> + reg = <0xe2000 0x1000>;
> + };
> +
> + sfp: sfp@e8000 {
> + compatible = "fsl,t1040-sfp";
> + reg = <0xe8000 0x1000>;
> + };
> +
> + serdes: serdes@ea000 {
> + compatible = "fsl,t1040-serdes";
> + reg = <0xea000 0x4000>;
> + };
> +
> +/include/ "qoriq-espi-0.dtsi"
> + spi@110000 {
> + fsl,espi-num-chipselects = <4>;
> + };
> +
> +/include/ "qoriq-esdhc-0.dtsi"
> + sdhc@114000 {
> + compatible = "fsl,t1040-esdhc", "fsl,esdhc";
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x530>; /* eSDHCLIODNR */
> + sdhci,auto-cmd12;
> + };
> +/include/ "qoriq-i2c-0.dtsi"
> +/include/ "qoriq-i2c-1.dtsi"
> +/include/ "qoriq-duart-0.dtsi"
> +/include/ "qoriq-duart-1.dtsi"
> +/include/ "qoriq-gpio-0.dtsi"
> +/include/ "qoriq-gpio-1.dtsi"
> +/include/ "qoriq-gpio-2.dtsi"
> +/include/ "qoriq-gpio-3.dtsi"
> +/include/ "qoriq-usb2-mph-0.dtsi"
> + usb0: usb@210000 {
> + compatible = "fsl-usb2-mph-v2.4", "fsl-usb2-mph";
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x520>; /* USB1LIODNR */
> + phy_type = "utmi";
> + port0;
> + };
> +/include/ "qoriq-usb2-dr-0.dtsi"
> + usb1: usb@211000 {
> + compatible = "fsl-usb2-dr-v2.4", "fsl-usb2-dr";
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x524>; /* USB2LIODNR */
> + dr_mode = "host";
> + phy_type = "utmi";
> + };
> +
> + display@180000 {
> + compatible = "fsl,t1040-diu", "fsl,diu";
> + reg = <0x180000 1000>;
> + interrupts = <74 2 0 0>;
> + };
> +
> +/include/ "qoriq-sata2-0.dtsi"
> +sata@220000 {
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x550>; /* SATA1LIODNR */
> +};
> +/include/ "qoriq-sata2-1.dtsi"
> +sata@221000 {
> + fsl,iommu-parent = <&pamu0>;
> + fsl,liodn-reg = <&guts 0x554>; /* SATA2LIODNR */
> +};
> +/include/ "qoriq-sec5.0-0.dtsi"
> +};
> diff --git a/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
> new file mode 100644
> index 0000000..319b74f
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/fsl/t1042si-post.dtsi
> @@ -0,0 +1,37 @@
> +/*
> + * T1042 Silicon/SoC Device Tree Source (post include)
> + *
> + * Copyright 2013 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +/include/ "t1040si-post.dtsi"
> +
> +/* Place holder for ethernet related device tree nodes */
> diff --git a/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
> new file mode 100644
> index 0000000..c0ae954
> --- /dev/null
> +++ b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
> @@ -0,0 +1,106 @@
> +/*
> + * T1040/T1042 Silicon/SoC Device Tree Source (pre include)
> + *
> + * Copyright 2013 Freescale Semiconductor Inc.
> + *
> + * Redistribution and use in source and binary forms, with or without
> + * modification, are permitted provided that the following conditions are met:
> + * * Redistributions of source code must retain the above copyright
> + * notice, this list of conditions and the following disclaimer.
> + * * Redistributions in binary form must reproduce the above copyright
> + * notice, this list of conditions and the following disclaimer in the
> + * documentation and/or other materials provided with the distribution.
> + * * Neither the name of Freescale Semiconductor nor the
> + * names of its contributors may be used to endorse or promote products
> + * derived from this software without specific prior written permission.
> + *
> + *
> + * ALTERNATIVELY, this software may be distributed under the terms of the
> + * GNU General Public License ("GPL") as published by the Free Software
> + * Foundation, either version 2 of that License or (at your option) any
> + * later version.
> + *
> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> + */
> +
> +/dts-v1/;
> +
> +/include/ "e5500_power_isa.dtsi"
> +
> +/ {
> + compatible = "fsl,T104x";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + interrupt-parent = <&mpic>;
> +
> + aliases {
> + ccsr = &soc;
> + dcsr = &dcsr;
> +
> + serial0 = &serial0;
> + serial1 = &serial1;
> + serial2 = &serial2;
> + serial3 = &serial3;
> + pci0 = &pci0;
> + pci1 = &pci1;
> + pci2 = &pci2;
> + pci3 = &pci3;
> + usb0 = &usb0;
> + usb1 = &usb1;
> + sdhc = &sdhc;
> +
> + crypto = &crypto;
> +
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: PowerPC,e5500@0 {
> + device_type = "cpu";
> + reg = <0>;
> + clocks = <&mux0>;
> + next-level-cache = <&L2_1>;
> + L2_1: l2-cache {
> + next-level-cache = <&cpc>;
> + };
> + };
> + cpu1: PowerPC,e5500@1 {
> + device_type = "cpu";
> + reg = <1>;
> + clocks = <&mux1>;
> + next-level-cache = <&L2_2>;
> + L2_2: l2-cache {
> + next-level-cache = <&cpc>;
> + };
> + };
> + cpu2: PowerPC,e5500@2 {
> + device_type = "cpu";
> + reg = <2>;
> + clocks = <&mux2>;
> + next-level-cache = <&L2_3>;
> + L2_3: l2-cache {
> + next-level-cache = <&cpc>;
> + };
> + };
> + cpu3: PowerPC,e5500@3 {
> + device_type = "cpu";
> + reg = <3>;
> + clocks = <&mux3>;
> + next-level-cache = <&L2_4>;
> + L2_4: l2-cache {
> + next-level-cache = <&cpc>;
> + };
> + };
> + };
> +};
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x
2013-10-21 3:37 ` Prabhakar Kushwaha
@ 2013-10-29 1:11 ` Scott Wood
2013-10-29 3:40 ` Prabhakar Kushwaha
0 siblings, 1 reply; 4+ messages in thread
From: Scott Wood @ 2013-10-29 1:11 UTC (permalink / raw)
To: Prabhakar Kushwaha
Cc: Varun Sethi, linuxppc-dev, Poonam Aggrwal, Priyanka Jain
On Mon, 2013-10-21 at 09:07 +0530, Prabhakar Kushwaha wrote:
> Hi Ben,
>
> This patch is present in upstream review list from a long time.
> There are no review comments.
>
> So, I request you to pick this patch-set for powerpc.git repository.
> http://patchwork.ozlabs.org/patch/280207/
> http://patchwork.ozlabs.org/patch/280208/
This revision has only been posted for about 2.5 weeks.
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + pll0: pll0@800 {
> > + #clock-cells = <1>;
> > + reg = <0x800 4>;
> > + compatible = "fsl,qoriq-core-pll-2.0";
> > + clocks = <&clockgen>;
> > + clock-output-names = "pll0", "pll0-div2", "pll0-div4";
> > + };
> > + pll1: pll1@820 {
> > + #clock-cells = <1>;
> > + reg = <0x820 4>;
> > + compatible = "fsl,qoriq-core-pll-2.0";
> > + clocks = <&clockgen>;
> > + clock-output-names = "pll1", "pll1-div2", "pll1-div4";
> > + };
> > + mux0: mux0@0 {
> > + #clock-cells = <0>;
> > + reg = <0x0 4>;
> > + compatible = "fsl,core-mux-clock";
> > + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
> > + <&pll1 0>, <&pll1 1>, <&pll1 2>;
> > + clock-names = "pll0_0", "pll0_1", "pll0_2",
> > + "pll1_0", "pll1_1", "pll1_2";
> > + clock-output-names = "cmux0";
> > + };
The clock bindings are still under discussion.
> > +++ b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
> > @@ -0,0 +1,106 @@
> > +/*
> > + * T1040/T1042 Silicon/SoC Device Tree Source (pre include)
> > + *
> > + * Copyright 2013 Freescale Semiconductor Inc.
> > + *
> > + * Redistribution and use in source and binary forms, with or without
> > + * modification, are permitted provided that the following conditions are met:
> > + * * Redistributions of source code must retain the above copyright
> > + * notice, this list of conditions and the following disclaimer.
> > + * * Redistributions in binary form must reproduce the above copyright
> > + * notice, this list of conditions and the following disclaimer in the
> > + * documentation and/or other materials provided with the distribution.
> > + * * Neither the name of Freescale Semiconductor nor the
> > + * names of its contributors may be used to endorse or promote products
> > + * derived from this software without specific prior written permission.
> > + *
> > + *
> > + * ALTERNATIVELY, this software may be distributed under the terms of the
> > + * GNU General Public License ("GPL") as published by the Free Software
> > + * Foundation, either version 2 of that License or (at your option) any
> > + * later version.
> > + *
> > + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
> > + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
> > + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
> > + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
> > + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
> > + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
> > + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
> > + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
> > + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
> > + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +/include/ "e5500_power_isa.dtsi"
> > +
> > +/ {
> > + compatible = "fsl,T104x";
No wildcards in compatibles. If your response is that this will get
overwritten anyway, then why have compatible here at all?
> > + crypto = &crypto;
> > +
> > + };
No blank lines before a closing brace.
-Scott
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x
2013-10-29 1:11 ` Scott Wood
@ 2013-10-29 3:40 ` Prabhakar Kushwaha
0 siblings, 0 replies; 4+ messages in thread
From: Prabhakar Kushwaha @ 2013-10-29 3:40 UTC (permalink / raw)
To: Scott Wood; +Cc: Varun Sethi, linuxppc-dev, Poonam Aggrwal, Priyanka Jain
On 10/29/2013 6:41 AM, Scott Wood wrote:
> On Mon, 2013-10-21 at 09:07 +0530, Prabhakar Kushwaha wrote:
>> Hi Ben,
>>
>> This patch is present in upstream review list from a long time.
>> There are no review comments.
>>
>> So, I request you to pick this patch-set for powerpc.git repository.
>> http://patchwork.ozlabs.org/patch/280207/
>> http://patchwork.ozlabs.org/patch/280208/
> This revision has only been posted for about 2.5 weeks.
>
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + pll0: pll0@800 {
>>> + #clock-cells = <1>;
>>> + reg = <0x800 4>;
>>> + compatible = "fsl,qoriq-core-pll-2.0";
>>> + clocks = <&clockgen>;
>>> + clock-output-names = "pll0", "pll0-div2", "pll0-div4";
>>> + };
>>> + pll1: pll1@820 {
>>> + #clock-cells = <1>;
>>> + reg = <0x820 4>;
>>> + compatible = "fsl,qoriq-core-pll-2.0";
>>> + clocks = <&clockgen>;
>>> + clock-output-names = "pll1", "pll1-div2", "pll1-div4";
>>> + };
>>> + mux0: mux0@0 {
>>> + #clock-cells = <0>;
>>> + reg = <0x0 4>;
>>> + compatible = "fsl,core-mux-clock";
>>> + clocks = <&pll0 0>, <&pll0 1>, <&pll0 2>,
>>> + <&pll1 0>, <&pll1 1>, <&pll1 2>;
>>> + clock-names = "pll0_0", "pll0_1", "pll0_2",
>>> + "pll1_0", "pll1_1", "pll1_2";
>>> + clock-output-names = "cmux0";
>>> + };
> The clock bindings are still under discussion.
I think, I should wait for clock bindings discussion :(
>>> +++ b/arch/powerpc/boot/dts/fsl/t104xsi-pre.dtsi
>>> @@ -0,0 +1,106 @@
>>> +/*
>>> + * T1040/T1042 Silicon/SoC Device Tree Source (pre include)
>>> + *
>>> + * Copyright 2013 Freescale Semiconductor Inc.
>>> + *
>>> + * Redistribution and use in source and binary forms, with or without
>>> + * modification, are permitted provided that the following conditions are met:
>>> + * * Redistributions of source code must retain the above copyright
>>> + * notice, this list of conditions and the following disclaimer.
>>> + * * Redistributions in binary form must reproduce the above copyright
>>> + * notice, this list of conditions and the following disclaimer in the
>>> + * documentation and/or other materials provided with the distribution.
>>> + * * Neither the name of Freescale Semiconductor nor the
>>> + * names of its contributors may be used to endorse or promote products
>>> + * derived from this software without specific prior written permission.
>>> + *
>>> + *
>>> + * ALTERNATIVELY, this software may be distributed under the terms of the
>>> + * GNU General Public License ("GPL") as published by the Free Software
>>> + * Foundation, either version 2 of that License or (at your option) any
>>> + * later version.
>>> + *
>>> + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY
>>> + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
>>> + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
>>> + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY
>>> + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
>>> + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
>>> + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
>>> + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
>>> + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
>>> + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
>>> + */
>>> +
>>> +/dts-v1/;
>>> +
>>> +/include/ "e5500_power_isa.dtsi"
>>> +
>>> +/ {
>>> + compatible = "fsl,T104x";
> No wildcards in compatibles. If your response is that this will get
> overwritten anyway, then why have compatible here at all?
I will take care of this
>>> + crypto = &crypto;
>>> +
>>> + };
> No blank lines before a closing brace.
>
>
I will take care of this.
Thanks,
Prabhakar
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2013-10-29 3:40 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-10-03 3:44 [PATCH 1/2][v8] powerpc/mpc85xx:Add initial device tree support of T104x Prabhakar Kushwaha
2013-10-21 3:37 ` Prabhakar Kushwaha
2013-10-29 1:11 ` Scott Wood
2013-10-29 3:40 ` Prabhakar Kushwaha
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).