* [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next
@ 2009-03-19 18:00 Anton Vorontsov
2009-03-19 18:01 ` [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards Anton Vorontsov
` (3 more replies)
0 siblings, 4 replies; 10+ messages in thread
From: Anton Vorontsov @ 2009-03-19 18:00 UTC (permalink / raw)
To: Kumar Gala; +Cc: Scott Wood, linuxppc-dev, Li Yang
On Wed, Mar 18, 2009 at 03:27:22PM -0500, Scott Wood wrote:
> Anton Vorontsov wrote:
>> On Wed, Mar 18, 2009 at 03:05:51PM -0500, Scott Wood wrote:
>>> Hmm, would that imply that the mdio underneath it is disabled as well?
>>
>> Technically, yes. In practice, MDIO and MAC drivers are probed
>> separately.
>
> Currently, yes, but that may not always be the case.
>
>> I don't see any better solution, should I just leave the core1's
>> mdio node intact?
>
> Probably. It's not as if core1 is going to be putting ethernet@24000 to
> sleep.
OK, so the updated patches no longer touch mpc8572ds_camp_core1.dts.
Other changes:
- Now the patch set depends on
"fsl_pq_mdio: Use proper address translation"
http://patchwork.ozlabs.org/patch/24698/
- Newly added gef_ppc9a board converted as well.
--
Anton Vorontsov
email: cbouatmailru@gmail.com
irc://irc.freenode.net/bd2
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards
2009-03-19 18:00 [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next Anton Vorontsov
@ 2009-03-19 18:01 ` Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes Anton Vorontsov
` (2 subsequent siblings)
3 siblings, 1 reply; 10+ messages in thread
From: Anton Vorontsov @ 2009-03-19 18:01 UTC (permalink / raw)
To: Kumar Gala; +Cc: Scott Wood, linuxppc-dev, Li Yang
This patch adds pmc nodes to the device tree files so that the boards
will able to use standby capability of MPC837x processors. The MPC837x
PMC controllers are compatible with MPC8349 ones (i.e. no deep sleep).
sleep = <> properties are used to specify SCCR masks as described
in "Specifying Device Power Management Information (sleep property)"
chapter in Documentation/powerpc/booting-without-of.txt.
Since I2C1 and eSDHC controllers share the same clock source, they
are now placed under sleep-nexus nodes.
A processor is able to wakeup the boards on LAN events (Wake-On-Lan),
console events (with no_console_suspend kernel command line), GPIO
events and external IRQs (IRQ1 and IRQ2).
The processor can also wakeup the boards by the fourth general purpose
timer in GTM1 block, but the GTM wakeup support isn't yet implemented
(it's tested to work, but it's unclear how can we use the quite short
GTM timers, and how do we want to expose the GTM to userspace).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/boot/dts/mpc8377_mds.dts | 68 ++++++++++++++++-------
arch/powerpc/boot/dts/mpc8377_rdb.dts | 98 +++++++++++++++++++++------------
arch/powerpc/boot/dts/mpc8378_mds.dts | 66 +++++++++++++++-------
arch/powerpc/boot/dts/mpc8378_rdb.dts | 96 ++++++++++++++++++++------------
arch/powerpc/boot/dts/mpc8379_mds.dts | 68 ++++++++++++++++-------
arch/powerpc/boot/dts/mpc8379_rdb.dts | 98 +++++++++++++++++++++------------
6 files changed, 323 insertions(+), 171 deletions(-)
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
index 3e3ec8f..cebfc50 100644
--- a/arch/powerpc/boot/dts/mpc8377_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -129,21 +129,38 @@
reg = <0x200 0x100>;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1374";
- reg = <0x68>;
- interrupts = <19 0x8>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
interrupt-parent = <&ipic>;
+ dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <0x68>;
+ interrupts = <19 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+ };
+
+ sdhci@2e000 {
+ compatible = "fsl,mpc8377-esdhc", "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -176,6 +193,7 @@
interrupts = <38 0x8>;
dr_mode = "host";
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -226,6 +244,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -240,6 +260,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy3>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -311,15 +333,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8377-esdhc", "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
sata@18000 {
@@ -327,6 +341,7 @@
reg = <0x18000 0x1000>;
interrupts = <44 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x000000c0>;
};
sata@19000 {
@@ -334,6 +349,7 @@
reg = <0x19000 0x1000>;
interrupts = <45 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000030>;
};
/* IPIC
@@ -349,6 +365,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8377-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -403,6 +426,7 @@
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
+ sleep = <&pmc 0x00010000>;
clock-frequency = <0>;
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -428,6 +452,7 @@
0 0 0 2 &ipic 1 8
0 0 0 3 &ipic 1 8
0 0 0 4 &ipic 1 8>;
+ sleep = <&pmc 0x00300000>;
clock-frequency = <0>;
pcie@0 {
@@ -459,6 +484,7 @@
0 0 0 2 &ipic 2 8
0 0 0 3 &ipic 2 8
0 0 0 4 &ipic 2 8>;
+ sleep = <&pmc 0x000c0000>;
clock-frequency = <0>;
pcie@0 {
diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts
index fb1d884..32311c8 100644
--- a/arch/powerpc/boot/dts/mpc8377_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts
@@ -127,37 +127,54 @@
gpio-controller;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
-
- dtt@48 {
- compatible = "national,lm75";
- reg = <0x48>;
- };
-
- at24@50 {
- compatible = "at24,24c256";
- reg = <0x50>;
- };
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+
+ dtt@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ at24@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+
+ mcu_pio: mcu@a {
+ #gpio-cells = <2>;
+ compatible = "fsl,mc9s08qg8-mpc8377erdb",
+ "fsl,mcu-mpc8349emitx";
+ reg = <0x0a>;
+ gpio-controller;
+ };
};
- mcu_pio: mcu@a {
- #gpio-cells = <2>;
- compatible = "fsl,mc9s08qg8-mpc8377erdb",
- "fsl,mcu-mpc8349emitx";
- reg = <0x0a>;
- gpio-controller;
+ sdhci@2e000 {
+ compatible = "fsl,mpc8377-esdhc", "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -228,6 +245,7 @@
interrupt-parent = <&ipic>;
interrupts = <38 0x8>;
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -272,6 +290,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -286,6 +306,8 @@
interrupt-parent = <&ipic>;
fixed-link = <1 1 1000 0 0>;
tbi-handle = <&tbi1>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -318,15 +340,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8377-esdhc", "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
sata@18000 {
@@ -334,6 +348,7 @@
reg = <0x18000 0x1000>;
interrupts = <44 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x000000c0>;
};
sata@19000 {
@@ -341,6 +356,7 @@
reg = <0x19000 0x1000>;
interrupts = <45 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000030>;
};
/* IPIC
@@ -356,6 +372,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8377-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -381,6 +404,7 @@
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+ sleep = <&pmc 0x00010000>;
clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -406,6 +430,7 @@
0 0 0 2 &ipic 1 8
0 0 0 3 &ipic 1 8
0 0 0 4 &ipic 1 8>;
+ sleep = <&pmc 0x00300000>;
clock-frequency = <0>;
pcie@0 {
@@ -437,6 +462,7 @@
0 0 0 2 &ipic 2 8
0 0 0 3 &ipic 2 8
0 0 0 4 &ipic 2 8>;
+ sleep = <&pmc 0x000c0000>;
clock-frequency = <0>;
pcie@0 {
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
index c3b212c..155841d 100644
--- a/arch/powerpc/boot/dts/mpc8378_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -129,21 +129,38 @@
reg = <0x200 0x100>;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1374";
- reg = <0x68>;
- interrupts = <19 0x8>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
interrupt-parent = <&ipic>;
+ dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <0x68>;
+ interrupts = <19 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+ };
+
+ sdhci@2e000 {
+ compatible = "fsl,mpc8378-esdhc", "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -215,6 +232,7 @@
interrupts = <38 0x8>;
dr_mode = "host";
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -265,6 +283,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -279,6 +299,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy3>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -311,15 +333,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8378-esdhc", "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
/* IPIC
@@ -335,6 +349,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8378-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -390,6 +411,7 @@
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
clock-frequency = <0>;
+ sleep = <&pmc 0x00010000>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
@@ -414,6 +436,7 @@
0 0 0 2 &ipic 1 8
0 0 0 3 &ipic 1 8
0 0 0 4 &ipic 1 8>;
+ sleep = <&pmc 0x00300000>;
clock-frequency = <0>;
pcie@0 {
@@ -445,6 +468,7 @@
0 0 0 2 &ipic 2 8
0 0 0 3 &ipic 2 8
0 0 0 4 &ipic 2 8>;
+ sleep = <&pmc 0x000c0000>;
clock-frequency = <0>;
pcie@0 {
diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts
index 37c8555..54ad96c 100644
--- a/arch/powerpc/boot/dts/mpc8378_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts
@@ -127,37 +127,54 @@
gpio-controller;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
-
- dtt@48 {
- compatible = "national,lm75";
- reg = <0x48>;
- };
-
- at24@50 {
- compatible = "at24,24c256";
- reg = <0x50>;
- };
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+
+ dtt@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ at24@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+
+ mcu_pio: mcu@a {
+ #gpio-cells = <2>;
+ compatible = "fsl,mc9s08qg8-mpc8378erdb",
+ "fsl,mcu-mpc8349emitx";
+ reg = <0x0a>;
+ gpio-controller;
+ };
};
- mcu_pio: mcu@a {
- #gpio-cells = <2>;
- compatible = "fsl,mc9s08qg8-mpc8378erdb",
- "fsl,mcu-mpc8349emitx";
- reg = <0x0a>;
- gpio-controller;
+ sdhci@2e000 {
+ compatible = "fsl,mpc8378-esdhc", "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -228,6 +245,7 @@
interrupt-parent = <&ipic>;
interrupts = <38 0x8>;
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -271,6 +289,8 @@
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -284,6 +304,8 @@
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
fixed-link = <1 1 1000 0 0>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -316,15 +338,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8378-esdhc", "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
/* IPIC
@@ -340,6 +354,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8378-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -365,6 +386,7 @@
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+ sleep = <&pmc 0x00010000>;
clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -390,6 +412,7 @@
0 0 0 2 &ipic 1 8
0 0 0 3 &ipic 1 8
0 0 0 4 &ipic 1 8>;
+ sleep = <&pmc 0x00300000>;
clock-frequency = <0>;
pcie@0 {
@@ -421,6 +444,7 @@
0 0 0 2 &ipic 2 8
0 0 0 3 &ipic 2 8
0 0 0 4 &ipic 2 8>;
+ sleep = <&pmc 0x000c0000>;
clock-frequency = <0>;
pcie@0 {
diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts
index 1b61cda..9deb5b2 100644
--- a/arch/powerpc/boot/dts/mpc8379_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8379_mds.dts
@@ -127,21 +127,38 @@
reg = <0x200 0x100>;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1374";
- reg = <0x68>;
- interrupts = <19 0x8>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
interrupt-parent = <&ipic>;
+ dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <0x68>;
+ interrupts = <19 0x8>;
+ interrupt-parent = <&ipic>;
+ };
+ };
+
+ sdhci@2e000 {
+ compatible = "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -213,6 +230,7 @@
interrupts = <38 0x8>;
dr_mode = "host";
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -262,6 +280,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -276,6 +296,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy3>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -308,15 +330,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
sata@18000 {
@@ -324,6 +338,7 @@
reg = <0x18000 0x1000>;
interrupts = <44 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x000000c0>;
};
sata@19000 {
@@ -331,6 +346,7 @@
reg = <0x19000 0x1000>;
interrupts = <45 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000030>;
};
sata@1a000 {
@@ -338,6 +354,7 @@
reg = <0x1a000 0x1000>;
interrupts = <46 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x0000000c>;
};
sata@1b000 {
@@ -345,6 +362,7 @@
reg = <0x1b000 0x1000>;
interrupts = <47 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000003>;
};
/* IPIC
@@ -360,6 +378,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8379-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -414,6 +439,7 @@
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe0300000 0x0 0x00100000>;
+ sleep = <&pmc 0x00010000>;
clock-frequency = <0>;
#interrupt-cells = <1>;
#size-cells = <2>;
diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts
index e2f98e6..3f4778f 100644
--- a/arch/powerpc/boot/dts/mpc8379_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts
@@ -125,37 +125,54 @@
gpio-controller;
};
- i2c@3000 {
+ sleep-nexus {
#address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- compatible = "fsl-i2c";
- reg = <0x3000 0x100>;
- interrupts = <14 0x8>;
- interrupt-parent = <&ipic>;
- dfsrr;
-
- dtt@48 {
- compatible = "national,lm75";
- reg = <0x48>;
- };
-
- at24@50 {
- compatible = "at24,24c256";
- reg = <0x50>;
- };
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ sleep = <&pmc 0x0c000000>;
+ ranges;
- rtc@68 {
- compatible = "dallas,ds1339";
- reg = <0x68>;
+ i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ compatible = "fsl-i2c";
+ reg = <0x3000 0x100>;
+ interrupts = <14 0x8>;
+ interrupt-parent = <&ipic>;
+ dfsrr;
+
+ dtt@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ at24@50 {
+ compatible = "at24,24c256";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+
+ mcu_pio: mcu@a {
+ #gpio-cells = <2>;
+ compatible = "fsl,mc9s08qg8-mpc8379erdb",
+ "fsl,mcu-mpc8349emitx";
+ reg = <0x0a>;
+ gpio-controller;
+ };
};
- mcu_pio: mcu@a {
- #gpio-cells = <2>;
- compatible = "fsl,mc9s08qg8-mpc8379erdb",
- "fsl,mcu-mpc8349emitx";
- reg = <0x0a>;
- gpio-controller;
+ sdhci@2e000 {
+ compatible = "fsl,mpc8379-esdhc";
+ reg = <0x2e000 0x1000>;
+ interrupts = <42 0x8>;
+ interrupt-parent = <&ipic>;
+ /* Filled in by U-Boot */
+ clock-frequency = <0>;
};
};
@@ -226,6 +243,7 @@
interrupt-parent = <&ipic>;
interrupts = <38 0x8>;
phy_type = "ulpi";
+ sleep = <&pmc 0x00c00000>;
};
mdio@24520 {
@@ -269,6 +287,8 @@
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+ sleep = <&pmc 0xc0000000>;
+ fsl,magic-packet;
};
enet1: ethernet@25000 {
@@ -283,6 +303,8 @@
interrupt-parent = <&ipic>;
fixed-link = <1 1 1000 0 0>;
tbi-handle = <&tbi1>;
+ sleep = <&pmc 0x30000000>;
+ fsl,magic-packet;
};
serial0: serial@4500 {
@@ -315,15 +337,7 @@
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x9fe>;
fsl,descriptor-types-mask = <0x3ab0ebf>;
- };
-
- sdhci@2e000 {
- compatible = "fsl,mpc8379-esdhc";
- reg = <0x2e000 0x1000>;
- interrupts = <42 0x8>;
- interrupt-parent = <&ipic>;
- /* Filled in by U-Boot */
- clock-frequency = <0>;
+ sleep = <&pmc 0x03000000>;
};
sata@18000 {
@@ -331,6 +345,7 @@
reg = <0x18000 0x1000>;
interrupts = <44 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x000000c0>;
};
sata@19000 {
@@ -338,6 +353,7 @@
reg = <0x19000 0x1000>;
interrupts = <45 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000030>;
};
sata@1a000 {
@@ -345,6 +361,7 @@
reg = <0x1a000 0x1000>;
interrupts = <46 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x0000000c>;
};
sata@1b000 {
@@ -352,6 +369,7 @@
reg = <0x1b000 0x1000>;
interrupts = <47 0x8>;
interrupt-parent = <&ipic>;
+ sleep = <&pmc 0x00000003>;
};
/* IPIC
@@ -367,6 +385,13 @@
#interrupt-cells = <2>;
reg = <0x700 0x100>;
};
+
+ pmc: power@b00 {
+ compatible = "fsl,mpc8379-pmc", "fsl,mpc8349-pmc";
+ reg = <0xb00 0x100 0xa00 0x100>;
+ interrupts = <80 0x8>;
+ interrupt-parent = <&ipic>;
+ };
};
pci0: pci@e0008500 {
@@ -392,6 +417,7 @@
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>;
+ sleep = <&pmc 0x00010000>;
clock-frequency = <66666666>;
#interrupt-cells = <1>;
#size-cells = <2>;
--
1.5.6.5
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:00 [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next Anton Vorontsov
2009-03-19 18:01 ` [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards Anton Vorontsov
@ 2009-03-19 18:01 ` Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 3/4] powerpc/85xx: " Anton Vorontsov
2009-03-19 18:01 ` [PATCH 4/4] powerpc/86xx: " Anton Vorontsov
3 siblings, 1 reply; 10+ messages in thread
From: Anton Vorontsov @ 2009-03-19 18:01 UTC (permalink / raw)
To: Kumar Gala; +Cc: Scott Wood, linuxppc-dev, Li Yang
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/boot/dts/asp834x-redboot.dts | 82 +++++++++++++++-------------
arch/powerpc/boot/dts/mpc8315erdb.dts | 80 +++++++++++++++-------------
arch/powerpc/boot/dts/mpc8349emitx.dts | 69 +++++++++++++-----------
arch/powerpc/boot/dts/mpc8349emitxgp.dts | 42 ++++++++-------
arch/powerpc/boot/dts/mpc834x_mds.dts | 81 +++++++++++++++-------------
arch/powerpc/boot/dts/mpc8377_mds.dts | 80 +++++++++++++++-------------
arch/powerpc/boot/dts/mpc8377_rdb.dts | 67 +++++++++++++-----------
arch/powerpc/boot/dts/mpc8378_mds.dts | 80 +++++++++++++++-------------
arch/powerpc/boot/dts/mpc8378_rdb.dts | 69 ++++++++++++++-----------
arch/powerpc/boot/dts/mpc8379_mds.dts | 79 +++++++++++++++------------
arch/powerpc/boot/dts/mpc8379_rdb.dts | 66 +++++++++++++----------
arch/powerpc/boot/dts/sbc8349.dts | 80 +++++++++++++++-------------
arch/powerpc/platforms/83xx/asp834x.c | 1 +
arch/powerpc/platforms/83xx/mpc834x_itx.c | 1 +
arch/powerpc/platforms/83xx/mpc834x_mds.c | 1 +
arch/powerpc/platforms/83xx/mpc837x_mds.c | 1 +
arch/powerpc/platforms/83xx/mpc837x_rdb.c | 1 +
arch/powerpc/platforms/83xx/sbc834x.c | 1 +
18 files changed, 488 insertions(+), 393 deletions(-)
diff --git a/arch/powerpc/boot/dts/asp834x-redboot.dts b/arch/powerpc/boot/dts/asp834x-redboot.dts
index 524af7e..7da84fd 100644
--- a/arch/powerpc/boot/dts/asp834x-redboot.dts
+++ b/arch/powerpc/boot/dts/asp834x-redboot.dts
@@ -181,70 +181,76 @@
phy_type = "ulpi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 08 e5 11 32 33 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
linux,network-index = <0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 08 e5 11 32 34 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
linux,network-index = <1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8315erdb.dts b/arch/powerpc/boot/dts/mpc8315erdb.dts
index 88d691c..3f4c5fb 100644
--- a/arch/powerpc/boot/dts/mpc8315erdb.dts
+++ b/arch/powerpc/boot/dts/mpc8315erdb.dts
@@ -190,66 +190,74 @@
phy_type = "utmi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy0: ethernet-phy@0 {
- interrupt-parent = <&ipic>;
- interrupts = <20 0x8>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&ipic>;
- interrupts = <19 0x8>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = < &phy0 >;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&ipic>;
+ interrupts = <20 0x8>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&ipic>;
+ interrupts = <19 0x8>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = < &phy1 >;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8349emitx.dts b/arch/powerpc/boot/dts/mpc8349emitx.dts
index b5eda94..1ae38f0 100644
--- a/arch/powerpc/boot/dts/mpc8349emitx.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitx.dts
@@ -170,57 +170,52 @@
phy_type = "ulpi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- /* Vitesse 8201 */
- phy1c: ethernet-phy@1c {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1c>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy1c>;
linux,network-index = <0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ /* Vitesse 8201 */
+ phy1c: ethernet-phy@1c {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1c>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
@@ -228,6 +223,18 @@
fixed-link = <1 1 1000 0 0>;
linux,network-index = <1>;
tbi-handle = <&tbi1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8349emitxgp.dts b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
index c87a601..662abe1 100644
--- a/arch/powerpc/boot/dts/mpc8349emitxgp.dts
+++ b/arch/powerpc/boot/dts/mpc8349emitxgp.dts
@@ -149,37 +149,41 @@
phy_type = "ulpi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- /* Vitesse 8201 */
- phy1c: ethernet-phy@1c {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1c>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy1c>;
linux,network-index = <0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ /* Vitesse 8201 */
+ phy1c: ethernet-phy@1c {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1c>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc834x_mds.dts b/arch/powerpc/boot/dts/mpc834x_mds.dts
index d9adba0..d9f0a23 100644
--- a/arch/powerpc/boot/dts/mpc834x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc834x_mds.dts
@@ -167,69 +167,76 @@
phy_type = "ulpi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
linux,network-index = <0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
linux,network-index = <1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8377_mds.dts b/arch/powerpc/boot/dts/mpc8377_mds.dts
index cebfc50..9637080 100644
--- a/arch/powerpc/boot/dts/mpc8377_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8377_mds.dts
@@ -196,48 +196,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -246,14 +213,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -262,6 +258,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8377_rdb.dts b/arch/powerpc/boot/dts/mpc8377_rdb.dts
index 32311c8..0533393 100644
--- a/arch/powerpc/boot/dts/mpc8377_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8377_rdb.dts
@@ -248,42 +248,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -292,14 +265,36 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -308,6 +303,18 @@
tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8378_mds.dts b/arch/powerpc/boot/dts/mpc8378_mds.dts
index 155841d..651ff2f 100644
--- a/arch/powerpc/boot/dts/mpc8378_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8378_mds.dts
@@ -235,48 +235,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -285,14 +252,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -301,6 +297,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8378_rdb.dts b/arch/powerpc/boot/dts/mpc8378_rdb.dts
index 54ad96c..5d90e85 100644
--- a/arch/powerpc/boot/dts/mpc8378_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8378_rdb.dts
@@ -248,64 +248,73 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
+ tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
interrupt-parent = <&ipic>;
fixed-link = <1 1 1000 0 0>;
+ tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8379_mds.dts b/arch/powerpc/boot/dts/mpc8379_mds.dts
index 9deb5b2..d6f208b 100644
--- a/arch/powerpc/boot/dts/mpc8379_mds.dts
+++ b/arch/powerpc/boot/dts/mpc8379_mds.dts
@@ -233,47 +233,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&ipic>;
- interrupts = <18 0x8>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -282,14 +250,43 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&ipic>;
+ interrupts = <18 0x8>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -298,6 +295,18 @@
phy-handle = <&phy3>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8379_rdb.dts b/arch/powerpc/boot/dts/mpc8379_rdb.dts
index 3f4778f..98ae95b 100644
--- a/arch/powerpc/boot/dts/mpc8379_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc8379_rdb.dts
@@ -246,41 +246,15 @@
sleep = <&pmc 0x00c00000>;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy2: ethernet-phy@2 {
- interrupt-parent = <&ipic>;
- interrupts = <17 0x8>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
phy-connection-type = "mii";
@@ -289,14 +263,36 @@
phy-handle = <&phy2>;
sleep = <&pmc 0xc0000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&ipic>;
+ interrupts = <17 0x8>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
phy-connection-type = "mii";
@@ -305,6 +301,18 @@
tbi-handle = <&tbi1>;
sleep = <&pmc 0x30000000>;
fsl,magic-packet;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/sbc8349.dts b/arch/powerpc/boot/dts/sbc8349.dts
index 8d365a5..a36dbbc 100644
--- a/arch/powerpc/boot/dts/sbc8349.dts
+++ b/arch/powerpc/boot/dts/sbc8349.dts
@@ -159,68 +159,76 @@
phy_type = "ulpi";
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@19 {
- interrupt-parent = <&ipic>;
- interrupts = <20 0x8>;
- reg = <0x19>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1a {
- interrupt-parent = <&ipic>;
- interrupts = <21 0x8>;
- reg = <0x1a>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <32 0x8 33 0x8 34 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
linux,network-index = <0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@19 {
+ interrupt-parent = <&ipic>;
+ interrupts = <20 0x8>;
+ reg = <0x19>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@1a {
+ interrupt-parent = <&ipic>;
+ interrupts = <21 0x8>;
+ reg = <0x1a>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 0x8 36 0x8 37 0x8>;
interrupt-parent = <&ipic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
linux,network-index = <1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/platforms/83xx/asp834x.c b/arch/powerpc/platforms/83xx/asp834x.c
index bb30d67..aa0d84d 100644
--- a/arch/powerpc/platforms/83xx/asp834x.c
+++ b/arch/powerpc/platforms/83xx/asp834x.c
@@ -58,6 +58,7 @@ static struct __initdata of_device_id asp8347_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/83xx/mpc834x_itx.c b/arch/powerpc/platforms/83xx/mpc834x_itx.c
index 76092d3..81e44fa 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_itx.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_itx.c
@@ -42,6 +42,7 @@
static struct of_device_id __initdata mpc834x_itx_ids[] = {
{ .compatible = "fsl,pq2pro-localbus", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/83xx/mpc834x_mds.c b/arch/powerpc/platforms/83xx/mpc834x_mds.c
index fc3f2ed..d0a634b 100644
--- a/arch/powerpc/platforms/83xx/mpc834x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc834x_mds.c
@@ -112,6 +112,7 @@ static struct of_device_id mpc834x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/83xx/mpc837x_mds.c b/arch/powerpc/platforms/83xx/mpc837x_mds.c
index 634785c..51df7e7 100644
--- a/arch/powerpc/platforms/83xx/mpc837x_mds.c
+++ b/arch/powerpc/platforms/83xx/mpc837x_mds.c
@@ -96,6 +96,7 @@ static struct of_device_id mpc837x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/83xx/mpc837x_rdb.c b/arch/powerpc/platforms/83xx/mpc837x_rdb.c
index 3d7b953..76f3b32 100644
--- a/arch/powerpc/platforms/83xx/mpc837x_rdb.c
+++ b/arch/powerpc/platforms/83xx/mpc837x_rdb.c
@@ -48,6 +48,7 @@ static struct of_device_id mpc837x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/83xx/sbc834x.c b/arch/powerpc/platforms/83xx/sbc834x.c
index 156c4e2..49023db 100644
--- a/arch/powerpc/platforms/83xx/sbc834x.c
+++ b/arch/powerpc/platforms/83xx/sbc834x.c
@@ -84,6 +84,7 @@ static struct __initdata of_device_id sbc834x_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
--
1.5.6.5
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 3/4] powerpc/85xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:00 [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next Anton Vorontsov
2009-03-19 18:01 ` [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards Anton Vorontsov
2009-03-19 18:01 ` [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes Anton Vorontsov
@ 2009-03-19 18:01 ` Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 4/4] powerpc/86xx: " Anton Vorontsov
3 siblings, 1 reply; 10+ messages in thread
From: Anton Vorontsov @ 2009-03-19 18:01 UTC (permalink / raw)
To: Kumar Gala; +Cc: Scott Wood, linuxppc-dev, Li Yang
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/boot/dts/ksi8560.dts | 79 ++++++-----
arch/powerpc/boot/dts/mpc8536ds.dts | 78 ++++++-----
arch/powerpc/boot/dts/mpc8540ads.dts | 117 +++++++++--------
arch/powerpc/boot/dts/mpc8541cds.dts | 78 ++++++-----
arch/powerpc/boot/dts/mpc8544ds.dts | 81 ++++++------
arch/powerpc/boot/dts/mpc8548cds.dts | 156 ++++++++++++----------
arch/powerpc/boot/dts/mpc8555cds.dts | 78 ++++++-----
arch/powerpc/boot/dts/mpc8560ads.dts | 102 ++++++++-------
arch/powerpc/boot/dts/mpc8568mds.dts | 102 ++++++++-------
arch/powerpc/boot/dts/mpc8572ds.dts | 150 ++++++++++++----------
arch/powerpc/boot/dts/mpc8572ds_36b.dts | 150 ++++++++++++----------
arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts | 39 +++---
arch/powerpc/boot/dts/sbc8548.dts | 78 ++++++-----
arch/powerpc/boot/dts/sbc8560.dts | 100 ++++++++-------
arch/powerpc/boot/dts/stx_gp3_8560.dts | 78 ++++++-----
arch/powerpc/boot/dts/tqm8540.dts | 117 +++++++++--------
arch/powerpc/boot/dts/tqm8541.dts | 90 +++++++------
arch/powerpc/boot/dts/tqm8548-bigflash.dts | 168 +++++++++++++-----------
arch/powerpc/boot/dts/tqm8548.dts | 168 +++++++++++++-----------
arch/powerpc/boot/dts/tqm8555.dts | 90 +++++++------
arch/powerpc/boot/dts/tqm8560.dts | 90 +++++++------
arch/powerpc/platforms/85xx/ksi8560.c | 1 +
arch/powerpc/platforms/85xx/mpc8536_ds.c | 1 +
arch/powerpc/platforms/85xx/mpc85xx_ads.c | 1 +
arch/powerpc/platforms/85xx/mpc85xx_cds.c | 1 +
arch/powerpc/platforms/85xx/mpc85xx_ds.c | 1 +
arch/powerpc/platforms/85xx/mpc85xx_mds.c | 1 +
arch/powerpc/platforms/85xx/sbc8548.c | 1 +
arch/powerpc/platforms/85xx/sbc8560.c | 1 +
arch/powerpc/platforms/85xx/stx_gp3.c | 1 +
arch/powerpc/platforms/85xx/tqm85xx.c | 1 +
31 files changed, 1183 insertions(+), 1016 deletions(-)
diff --git a/arch/powerpc/boot/dts/ksi8560.dts b/arch/powerpc/boot/dts/ksi8560.dts
index 3bfff47..308fe7c 100644
--- a/arch/powerpc/boot/dts/ksi8560.dts
+++ b/arch/powerpc/boot/dts/ksi8560.dts
@@ -124,67 +124,72 @@
};
};
- mdio@24520 { /* For TSECs */
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- PHY1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
-
- PHY2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
/* Mac address filled in by bootwrapper */
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&PHY1>;
+
+ mdio@520 { /* For TSECs */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ PHY1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ PHY2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
/* Mac address filled in by bootwrapper */
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&PHY2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
mpic: pic@40000 {
diff --git a/arch/powerpc/boot/dts/mpc8536ds.dts b/arch/powerpc/boot/dts/mpc8536ds.dts
index 3c905df..b31c504 100644
--- a/arch/powerpc/boot/dts/mpc8536ds.dts
+++ b/arch/powerpc/boot/dts/mpc8536ds.dts
@@ -137,42 +137,6 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 0x1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 0x1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
usb@22000 {
compatible = "fsl,mpc8536-usb2-mph", "fsl-usb2-mph";
reg = <0x22000 0x1000>;
@@ -194,31 +158,73 @@
};
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 0x1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 0x1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
usb@2b000 {
diff --git a/arch/powerpc/boot/dts/mpc8540ads.dts b/arch/powerpc/boot/dts/mpc8540ads.dts
index 79570ff..ddd67be 100644
--- a/arch/powerpc/boot/dts/mpc8540ads.dts
+++ b/arch/powerpc/boot/dts/mpc8540ads.dts
@@ -126,97 +126,106 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <7 1>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "FEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <41 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8541cds.dts b/arch/powerpc/boot/dts/mpc8541cds.dts
index 221036a..e45097f 100644
--- a/arch/powerpc/boot/dts/mpc8541cds.dts
+++ b/arch/powerpc/boot/dts/mpc8541cds.dts
@@ -126,66 +126,72 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts
index 0668d10..7c6932b 100644
--- a/arch/powerpc/boot/dts/mpc8544ds.dts
+++ b/arch/powerpc/boot/dts/mpc8544ds.dts
@@ -98,44 +98,6 @@
dfsrr;
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
dma@21300 {
#address-cells = <1>;
#size-cells = <1>;
@@ -178,31 +140,74 @@
};
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
tbi-handle = <&tbi0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
tbi-handle = <&tbi1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8548cds.dts b/arch/powerpc/boot/dts/mpc8548cds.dts
index df774a7..804e903 100644
--- a/arch/powerpc/boot/dts/mpc8548cds.dts
+++ b/arch/powerpc/boot/dts/mpc8548cds.dts
@@ -142,129 +142,141 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
/* eTSEC 3/4 are currently broken
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
*/
diff --git a/arch/powerpc/boot/dts/mpc8555cds.dts b/arch/powerpc/boot/dts/mpc8555cds.dts
index 053b01e..9484f07 100644
--- a/arch/powerpc/boot/dts/mpc8555cds.dts
+++ b/arch/powerpc/boot/dts/mpc8555cds.dts
@@ -126,66 +126,72 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8560ads.dts b/arch/powerpc/boot/dts/mpc8560ads.dts
index 11b1bcb..cc2acf8 100644
--- a/arch/powerpc/boot/dts/mpc8560ads.dts
+++ b/arch/powerpc/boot/dts/mpc8560ads.dts
@@ -115,78 +115,84 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <5 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <7 1>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <7 1>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <7 1>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
mpic: pic@40000 {
diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts
index 1955bd9..9d52e3b 100644
--- a/arch/powerpc/boot/dts/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/mpc8568mds.dts
@@ -149,78 +149,84 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@7 {
- interrupt-parent = <&mpic>;
- interrupts = <1 1>;
- reg = <0x7>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <1 1>;
- reg = <0x2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <2 1>;
- reg = <0x3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@7 {
+ interrupt-parent = <&mpic>;
+ interrupts = <1 1>;
+ reg = <0x7>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <1 1>;
+ reg = <0x2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <2 1>;
+ reg = <0x3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8572ds.dts b/arch/powerpc/boot/dts/mpc8572ds.dts
index 6c9354b..6e79a41 100644
--- a/arch/powerpc/boot/dts/mpc8572ds.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds.dts
@@ -312,129 +312,141 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x3>;
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x2>;
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x3>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy2>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy3>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8572ds_36b.dts b/arch/powerpc/boot/dts/mpc8572ds_36b.dts
index fc7dbf4..dbd81a7 100644
--- a/arch/powerpc/boot/dts/mpc8572ds_36b.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds_36b.dts
@@ -312,129 +312,141 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x2>;
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x3>;
- };
-
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x2>;
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x3>;
+ };
+
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy2>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy3>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
index 32178bf..2bc0c71 100644
--- a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
+++ b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts
@@ -148,35 +148,38 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x0>;
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1>;
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x0>;
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1>;
+ };
+ };
};
enet1: ethernet@25000 {
diff --git a/arch/powerpc/boot/dts/sbc8548.dts b/arch/powerpc/boot/dts/sbc8548.dts
index 2baf4a5..9c5079f 100644
--- a/arch/powerpc/boot/dts/sbc8548.dts
+++ b/arch/powerpc/boot/dts/sbc8548.dts
@@ -234,66 +234,72 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@19 {
- interrupt-parent = <&mpic>;
- interrupts = <0x6 0x1>;
- reg = <0x19>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1a {
- interrupt-parent = <&mpic>;
- interrupts = <0x7 0x1>;
- reg = <0x1a>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@19 {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x6 0x1>;
+ reg = <0x19>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1a {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x7 0x1>;
+ reg = <0x1a>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/sbc8560.dts b/arch/powerpc/boot/dts/sbc8560.dts
index 01542f7..b772405 100644
--- a/arch/powerpc/boot/dts/sbc8560.dts
+++ b/arch/powerpc/boot/dts/sbc8560.dts
@@ -139,77 +139,83 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
- phy0: ethernet-phy@19 {
- interrupt-parent = <&mpic>;
- interrupts = <0x6 0x1>;
- reg = <0x19>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1a {
- interrupt-parent = <&mpic>;
- interrupts = <0x7 0x1>;
- reg = <0x1a>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@1b {
- interrupt-parent = <&mpic>;
- interrupts = <0x8 0x1>;
- reg = <0x1b>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@1c {
- interrupt-parent = <&mpic>;
- interrupts = <0x8 0x1>;
- reg = <0x1c>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+ phy0: ethernet-phy@19 {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x6 0x1>;
+ reg = <0x19>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1a {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x7 0x1>;
+ reg = <0x1a>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1b {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x8 0x1>;
+ reg = <0x1b>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@1c {
+ interrupt-parent = <&mpic>;
+ interrupts = <0x8 0x1>;
+ reg = <0x1c>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x23 0x2 0x24 0x2 0x28 0x2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
mpic: pic@40000 {
diff --git a/arch/powerpc/boot/dts/stx_gp3_8560.dts b/arch/powerpc/boot/dts/stx_gp3_8560.dts
index fff33fe..8b17395 100644
--- a/arch/powerpc/boot/dts/stx_gp3_8560.dts
+++ b/arch/powerpc/boot/dts/stx_gp3_8560.dts
@@ -124,66 +124,72 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <5 4>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy4: ethernet-phy@4 {
- interrupt-parent = <&mpic>;
- interrupts = <5 4>;
- reg = <4>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 4>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&mpic>;
+ interrupts = <5 4>;
+ reg = <4>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy4>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
mpic: pic@40000 {
diff --git a/arch/powerpc/boot/dts/tqm8540.dts b/arch/powerpc/boot/dts/tqm8540.dts
index 39e55ab..ac9413a 100644
--- a/arch/powerpc/boot/dts/tqm8540.dts
+++ b/arch/powerpc/boot/dts/tqm8540.dts
@@ -136,94 +136,103 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "FEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <41 2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/tqm8541.dts b/arch/powerpc/boot/dts/tqm8541.dts
index 58ae8bc..c71bb5d 100644
--- a/arch/powerpc/boot/dts/tqm8541.dts
+++ b/arch/powerpc/boot/dts/tqm8541.dts
@@ -135,72 +135,78 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/tqm8548-bigflash.dts b/arch/powerpc/boot/dts/tqm8548-bigflash.dts
index bff380a..28b1a95 100644
--- a/arch/powerpc/boot/dts/tqm8548-bigflash.dts
+++ b/arch/powerpc/boot/dts/tqm8548-bigflash.dts
@@ -148,134 +148,146 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- phy4: ethernet-phy@4 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <4>;
- device_type = "ethernet-phy";
- };
- phy5: ethernet-phy@5 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <5>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <4>;
+ device_type = "ethernet-phy";
+ };
+ phy5: ethernet-phy@5 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <5>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy4>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/tqm8548.dts b/arch/powerpc/boot/dts/tqm8548.dts
index 112ac90..826fb62 100644
--- a/arch/powerpc/boot/dts/tqm8548.dts
+++ b/arch/powerpc/boot/dts/tqm8548.dts
@@ -148,134 +148,146 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- phy4: ethernet-phy@4 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <4>;
- device_type = "ethernet-phy";
- };
- phy5: ethernet-phy@5 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <5>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ phy4: ethernet-phy@4 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <4>;
+ device_type = "ethernet-phy";
+ };
+ phy5: ethernet-phy@5 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <5>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy3>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy4>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/tqm8555.dts b/arch/powerpc/boot/dts/tqm8555.dts
index 4b7da89..a133ded 100644
--- a/arch/powerpc/boot/dts/tqm8555.dts
+++ b/arch/powerpc/boot/dts/tqm8555.dts
@@ -135,72 +135,78 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/tqm8560.dts b/arch/powerpc/boot/dts/tqm8560.dts
index 3fa552f..649e2e5 100644
--- a/arch/powerpc/boot/dts/tqm8560.dts
+++ b/arch/powerpc/boot/dts/tqm8560.dts
@@ -137,72 +137,78 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <8 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy2>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <8 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
mpic: pic@40000 {
diff --git a/arch/powerpc/platforms/85xx/ksi8560.c b/arch/powerpc/platforms/85xx/ksi8560.c
index 66f2923..f4d36b5 100644
--- a/arch/powerpc/platforms/85xx/ksi8560.c
+++ b/arch/powerpc/platforms/85xx/ksi8560.c
@@ -219,6 +219,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
{ .type = "simple-bus", },
{ .name = "cpm", },
{ .name = "localbus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/mpc8536_ds.c b/arch/powerpc/platforms/85xx/mpc8536_ds.c
index 1bf5aef..63efca2 100644
--- a/arch/powerpc/platforms/85xx/mpc8536_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc8536_ds.c
@@ -92,6 +92,7 @@ static struct of_device_id __initdata mpc8536_ds_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ads.c b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
index 21f0090..9438a89 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ads.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ads.c
@@ -226,6 +226,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
{ .name = "cpm", },
{ .name = "localbus", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_cds.c b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
index aeb6a5b..0a9e491 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_cds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_cds.c
@@ -336,6 +336,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_ds.c b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
index 7326d90..de66de7 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_ds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_ds.c
@@ -204,6 +204,7 @@ static struct of_device_id __initdata mpc85xxds_ids[] = {
{ .type = "soc", },
{ .compatible = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/mpc85xx_mds.c b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
index 658a36f..7dd0290 100644
--- a/arch/powerpc/platforms/85xx/mpc85xx_mds.c
+++ b/arch/powerpc/platforms/85xx/mpc85xx_mds.c
@@ -265,6 +265,7 @@ static struct of_device_id mpc85xx_ids[] = {
{ .compatible = "simple-bus", },
{ .type = "qe", },
{ .compatible = "fsl,qe", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/sbc8548.c b/arch/powerpc/platforms/85xx/sbc8548.c
index 7ec77ce..ecdd8c0 100644
--- a/arch/powerpc/platforms/85xx/sbc8548.c
+++ b/arch/powerpc/platforms/85xx/sbc8548.c
@@ -154,6 +154,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
{ .name = "soc", },
{ .type = "soc", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/sbc8560.c b/arch/powerpc/platforms/85xx/sbc8560.c
index 472f254..cc27807 100644
--- a/arch/powerpc/platforms/85xx/sbc8560.c
+++ b/arch/powerpc/platforms/85xx/sbc8560.c
@@ -213,6 +213,7 @@ static struct of_device_id __initdata of_bus_ids[] = {
{ .name = "cpm", },
{ .name = "localbus", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/stx_gp3.c b/arch/powerpc/platforms/85xx/stx_gp3.c
index 0cca8f5..f559918 100644
--- a/arch/powerpc/platforms/85xx/stx_gp3.c
+++ b/arch/powerpc/platforms/85xx/stx_gp3.c
@@ -145,6 +145,7 @@ static void stx_gp3_show_cpuinfo(struct seq_file *m)
static struct of_device_id __initdata of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/85xx/tqm85xx.c b/arch/powerpc/platforms/85xx/tqm85xx.c
index 2933a8e..5b0ab99 100644
--- a/arch/powerpc/platforms/85xx/tqm85xx.c
+++ b/arch/powerpc/platforms/85xx/tqm85xx.c
@@ -153,6 +153,7 @@ static void tqm85xx_show_cpuinfo(struct seq_file *m)
static struct of_device_id __initdata of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
--
1.5.6.5
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 4/4] powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:00 [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next Anton Vorontsov
` (2 preceding siblings ...)
2009-03-19 18:01 ` [PATCH 3/4] powerpc/85xx: " Anton Vorontsov
@ 2009-03-19 18:01 ` Anton Vorontsov
2009-03-20 9:38 ` Martyn Welch
2009-03-24 13:33 ` Kumar Gala
3 siblings, 2 replies; 10+ messages in thread
From: Anton Vorontsov @ 2009-03-19 18:01 UTC (permalink / raw)
To: Kumar Gala; +Cc: Scott Wood, linuxppc-dev, Li Yang
Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
arch/powerpc/boot/dts/gef_ppc9a.dts | 39 ++++---
arch/powerpc/boot/dts/gef_sbc310.dts | 39 ++++---
arch/powerpc/boot/dts/gef_sbc610.dts | 39 ++++---
arch/powerpc/boot/dts/mpc8641_hpcn.dts | 157 +++++++++++++++-------------
arch/powerpc/boot/dts/sbc8641d.dts | 156 +++++++++++++++-------------
arch/powerpc/platforms/86xx/gef_ppc9a.c | 1 +
arch/powerpc/platforms/86xx/gef_sbc310.c | 1 +
arch/powerpc/platforms/86xx/gef_sbc610.c | 1 +
arch/powerpc/platforms/86xx/mpc8610_hpcd.c | 1 +
arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 1 +
arch/powerpc/platforms/86xx/sbc8641d.c | 1 +
11 files changed, 237 insertions(+), 199 deletions(-)
diff --git a/arch/powerpc/boot/dts/gef_ppc9a.dts b/arch/powerpc/boot/dts/gef_ppc9a.dts
index 0ddfdfc..d47ad07 100644
--- a/arch/powerpc/boot/dts/gef_ppc9a.dts
+++ b/arch/powerpc/boot/dts/gef_ppc9a.dts
@@ -247,34 +247,37 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x9 0x4>;
- reg = <1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x8 0x4>;
- reg = <3>;
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "gmii";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x9 0x4>;
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x8 0x4>;
+ reg = <3>;
+ };
+ };
};
enet1: ethernet@26000 {
diff --git a/arch/powerpc/boot/dts/gef_sbc310.dts b/arch/powerpc/boot/dts/gef_sbc310.dts
index 09eeb43..1569117 100644
--- a/arch/powerpc/boot/dts/gef_sbc310.dts
+++ b/arch/powerpc/boot/dts/gef_sbc310.dts
@@ -247,34 +247,37 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x9 0x4>;
- reg = <1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x8 0x4>;
- reg = <3>;
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "gmii";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x9 0x4>;
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x8 0x4>;
+ reg = <3>;
+ };
+ };
};
enet1: ethernet@26000 {
diff --git a/arch/powerpc/boot/dts/gef_sbc610.dts b/arch/powerpc/boot/dts/gef_sbc610.dts
index 714175c..6582dbd 100644
--- a/arch/powerpc/boot/dts/gef_sbc610.dts
+++ b/arch/powerpc/boot/dts/gef_sbc610.dts
@@ -202,34 +202,37 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x9 0x4>;
- reg = <1>;
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&gef_pic>;
- interrupts = <0x8 0x4>;
- reg = <3>;
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "eTSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>;
interrupt-parent = <&mpic>;
phy-handle = <&phy0>;
phy-connection-type = "gmii";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x9 0x4>;
+ reg = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&gef_pic>;
+ interrupts = <0x8 0x4>;
+ reg = <3>;
+ };
+ };
};
enet1: ethernet@26000 {
diff --git a/arch/powerpc/boot/dts/mpc8641_hpcn.dts b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
index 4481532..d72beb1 100644
--- a/arch/powerpc/boot/dts/mpc8641_hpcn.dts
+++ b/arch/powerpc/boot/dts/mpc8641_hpcn.dts
@@ -180,133 +180,144 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@3 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@3 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy2>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy3>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/boot/dts/sbc8641d.dts b/arch/powerpc/boot/dts/sbc8641d.dts
index 36db981..e3e914e 100644
--- a/arch/powerpc/boot/dts/sbc8641d.dts
+++ b/arch/powerpc/boot/dts/sbc8641d.dts
@@ -192,132 +192,144 @@
};
};
- mdio@24520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-mdio";
- reg = <0x24520 0x20>;
-
- phy0: ethernet-phy@1f {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0x1f>;
- device_type = "ethernet-phy";
- };
- phy1: ethernet-phy@0 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
- phy2: ethernet-phy@1 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
- phy3: ethernet-phy@2 {
- interrupt-parent = <&mpic>;
- interrupts = <10 1>;
- reg = <2>;
- device_type = "ethernet-phy";
- };
- tbi0: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@25520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x25520 0x20>;
-
- tbi1: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@26520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x26520 0x20>;
-
- tbi2: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
- mdio@27520 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,gianfar-tbi";
- reg = <0x27520 0x20>;
-
- tbi3: tbi-phy@11 {
- reg = <0x11>;
- device_type = "tbi-phy";
- };
- };
-
enet0: ethernet@24000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x24000 0x1000>;
+ ranges = <0x0 0x24000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <29 2 30 2 34 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi0>;
phy-handle = <&phy0>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-mdio";
+ reg = <0x520 0x20>;
+
+ phy0: ethernet-phy@1f {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0x1f>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@0 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ phy2: ethernet-phy@1 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy3: ethernet-phy@2 {
+ interrupt-parent = <&mpic>;
+ interrupts = <10 1>;
+ reg = <2>;
+ device_type = "ethernet-phy";
+ };
+ tbi0: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet1: ethernet@25000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <1>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x25000 0x1000>;
+ ranges = <0x0 0x25000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <35 2 36 2 40 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi1>;
phy-handle = <&phy1>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi1: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet2: ethernet@26000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <2>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x26000 0x1000>;
+ ranges = <0x0 0x26000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <31 2 32 2 33 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi2>;
phy-handle = <&phy2>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi2: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
enet3: ethernet@27000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
cell-index = <3>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
reg = <0x27000 0x1000>;
+ ranges = <0x0 0x27000 0x1000>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <37 2 38 2 39 2>;
interrupt-parent = <&mpic>;
tbi-handle = <&tbi3>;
phy-handle = <&phy3>;
phy-connection-type = "rgmii-id";
+
+ mdio@520 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,gianfar-tbi";
+ reg = <0x520 0x20>;
+
+ tbi3: tbi-phy@11 {
+ reg = <0x11>;
+ device_type = "tbi-phy";
+ };
+ };
};
serial0: serial@4500 {
diff --git a/arch/powerpc/platforms/86xx/gef_ppc9a.c b/arch/powerpc/platforms/86xx/gef_ppc9a.c
index 830fd9a..d791046 100644
--- a/arch/powerpc/platforms/86xx/gef_ppc9a.c
+++ b/arch/powerpc/platforms/86xx/gef_ppc9a.c
@@ -194,6 +194,7 @@ static long __init mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/86xx/gef_sbc310.c b/arch/powerpc/platforms/86xx/gef_sbc310.c
index ba3ce43..af14f85 100644
--- a/arch/powerpc/platforms/86xx/gef_sbc310.c
+++ b/arch/powerpc/platforms/86xx/gef_sbc310.c
@@ -205,6 +205,7 @@ static long __init mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/86xx/gef_sbc610.c b/arch/powerpc/platforms/86xx/gef_sbc610.c
index d6b772b..ea23606 100644
--- a/arch/powerpc/platforms/86xx/gef_sbc610.c
+++ b/arch/powerpc/platforms/86xx/gef_sbc610.c
@@ -194,6 +194,7 @@ static long __init mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
index e8d54ac..3f49a6f 100644
--- a/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
+++ b/arch/powerpc/platforms/86xx/mpc8610_hpcd.c
@@ -46,6 +46,7 @@ static unsigned char *pixis_bdcfg0, *pixis_arch;
static struct of_device_id __initdata mpc8610_ids[] = {
{ .compatible = "fsl,mpc8610-immr", },
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{}
};
diff --git a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
index 27e0e68..c4ec49b 100644
--- a/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
+++ b/arch/powerpc/platforms/86xx/mpc86xx_hpcn.c
@@ -148,6 +148,7 @@ mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
{ .compatible = "fsl,rapidio-delta", },
+ { .compatible = "gianfar", },
{},
};
diff --git a/arch/powerpc/platforms/86xx/sbc8641d.c b/arch/powerpc/platforms/86xx/sbc8641d.c
index 5fd7ed4..2886a36 100644
--- a/arch/powerpc/platforms/86xx/sbc8641d.c
+++ b/arch/powerpc/platforms/86xx/sbc8641d.c
@@ -103,6 +103,7 @@ mpc86xx_time_init(void)
static __initdata struct of_device_id of_bus_ids[] = {
{ .compatible = "simple-bus", },
+ { .compatible = "gianfar", },
{},
};
--
1.5.6.5
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH 4/4] powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:01 ` [PATCH 4/4] powerpc/86xx: " Anton Vorontsov
@ 2009-03-20 9:38 ` Martyn Welch
2009-03-24 13:33 ` Kumar Gala
1 sibling, 0 replies; 10+ messages in thread
From: Martyn Welch @ 2009-03-20 9:38 UTC (permalink / raw)
To: Anton Vorontsov; +Cc: Scott Wood, linuxppc-dev, Li Yang
Anton Vorontsov wrote:
> Currently it doesn't matter where the mdio nodes are placed, but with
> power management support (i.e. when sleep = <> properties will take
> effect), mdio nodes placement will become important: mdio controller
> is a part of the ethernet block, so the mdio nodes should be placed
> correctly. Otherwise we may wrongly assume that MDIO controllers are
> available during sleep.
>
> Suggested-by: Scott Wood <scottwood@freescale.com>
> Suggested-by: Kumar Gala <galak@kernel.crashing.org>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/gef_ppc9a.dts | 39 ++++---
> arch/powerpc/boot/dts/gef_sbc310.dts | 39 ++++---
> arch/powerpc/boot/dts/gef_sbc610.dts | 39 ++++---
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 157 +++++++++++++++-------------
> arch/powerpc/boot/dts/sbc8641d.dts | 156 +++++++++++++++-------------
> arch/powerpc/platforms/86xx/gef_ppc9a.c | 1 +
> arch/powerpc/platforms/86xx/gef_sbc310.c | 1 +
> arch/powerpc/platforms/86xx/gef_sbc610.c | 1 +
> arch/powerpc/platforms/86xx/mpc8610_hpcd.c | 1 +
> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 1 +
> arch/powerpc/platforms/86xx/sbc8641d.c | 1 +
> 11 files changed, 237 insertions(+), 199 deletions(-)
>
Tested on ppc9a. Other GE Fanuc boards look sane.
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
Martyn
--
Martyn Welch MEng MPhil MIET (Principal Software Engineer) T:+44(0)1327322748
GE Fanuc Intelligent Platforms Ltd, |Registered in England and Wales
Tove Valley Business Park, Towcester, |(3828642) at 100 Barbirolli Square,
Northants, NN12 6PF, UK T:+44(0)1327359444 |Manchester,M2 3AB VAT:GB 729849476
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards
2009-03-19 18:01 ` [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards Anton Vorontsov
@ 2009-03-24 13:33 ` Kumar Gala
0 siblings, 0 replies; 10+ messages in thread
From: Kumar Gala @ 2009-03-24 13:33 UTC (permalink / raw)
To: Anton Vorontsov; +Cc: Scott Wood, linuxppc-dev, Li Yang
On Mar 19, 2009, at 1:01 PM, Anton Vorontsov wrote:
> This patch adds pmc nodes to the device tree files so that the boards
> will able to use standby capability of MPC837x processors. The MPC837x
> PMC controllers are compatible with MPC8349 ones (i.e. no deep sleep).
>
> sleep = <> properties are used to specify SCCR masks as described
> in "Specifying Device Power Management Information (sleep property)"
> chapter in Documentation/powerpc/booting-without-of.txt.
>
> Since I2C1 and eSDHC controllers share the same clock source, they
> are now placed under sleep-nexus nodes.
>
> A processor is able to wakeup the boards on LAN events (Wake-On-Lan),
> console events (with no_console_suspend kernel command line), GPIO
> events and external IRQs (IRQ1 and IRQ2).
>
> The processor can also wakeup the boards by the fourth general purpose
> timer in GTM1 block, but the GTM wakeup support isn't yet implemented
> (it's tested to work, but it's unclear how can we use the quite short
> GTM timers, and how do we want to expose the GTM to userspace).
>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/mpc8377_mds.dts | 68 ++++++++++++++++-------
> arch/powerpc/boot/dts/mpc8377_rdb.dts | 98 ++++++++++++++++++++
> +------------
> arch/powerpc/boot/dts/mpc8378_mds.dts | 66 +++++++++++++++-------
> arch/powerpc/boot/dts/mpc8378_rdb.dts | 96 +++++++++++++++++++
> +------------
> arch/powerpc/boot/dts/mpc8379_mds.dts | 68 ++++++++++++++++-------
> arch/powerpc/boot/dts/mpc8379_rdb.dts | 98 ++++++++++++++++++++
> +------------
> 6 files changed, 323 insertions(+), 171 del
applied to next
- k
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:01 ` [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes Anton Vorontsov
@ 2009-03-24 13:33 ` Kumar Gala
0 siblings, 0 replies; 10+ messages in thread
From: Kumar Gala @ 2009-03-24 13:33 UTC (permalink / raw)
To: Anton Vorontsov; +Cc: Scott Wood, linuxppc-dev, Li Yang
On Mar 19, 2009, at 1:01 PM, Anton Vorontsov wrote:
> Currently it doesn't matter where the mdio nodes are placed, but with
> power management support (i.e. when sleep = <> properties will take
> effect), mdio nodes placement will become important: mdio controller
> is a part of the ethernet block, so the mdio nodes should be placed
> correctly. Otherwise we may wrongly assume that MDIO controllers are
> available during sleep.
>
> Suggested-by: Scott Wood <scottwood@freescale.com>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/asp834x-redboot.dts | 82 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/mpc8315erdb.dts | 80 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/mpc8349emitx.dts | 69 ++++++++++++
> +-----------
> arch/powerpc/boot/dts/mpc8349emitxgp.dts | 42 ++++++++-------
> arch/powerpc/boot/dts/mpc834x_mds.dts | 81 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/mpc8377_mds.dts | 80 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/mpc8377_rdb.dts | 67 ++++++++++++
> +-----------
> arch/powerpc/boot/dts/mpc8378_mds.dts | 80 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/mpc8378_rdb.dts | 69 +++++++++++++
> +-----------
> arch/powerpc/boot/dts/mpc8379_mds.dts | 79 ++++++++++++++
> +------------
> arch/powerpc/boot/dts/mpc8379_rdb.dts | 66 ++++++++++++
> +----------
> arch/powerpc/boot/dts/sbc8349.dts | 80 ++++++++++++++
> +-------------
> arch/powerpc/platforms/83xx/asp834x.c | 1 +
> arch/powerpc/platforms/83xx/mpc834x_itx.c | 1 +
> arch/powerpc/platforms/83xx/mpc834x_mds.c | 1 +
> arch/powerpc/platforms/83xx/mpc837x_mds.c | 1 +
> arch/powerpc/platforms/83xx/mpc837x_rdb.c | 1 +
> arch/powerpc/platforms/83xx/sbc834x.c | 1 +
> 18 files changed, 488 insertions(+), 393 deletions(-)
applied to next
- k
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 3/4] powerpc/85xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:01 ` [PATCH 3/4] powerpc/85xx: " Anton Vorontsov
@ 2009-03-24 13:33 ` Kumar Gala
0 siblings, 0 replies; 10+ messages in thread
From: Kumar Gala @ 2009-03-24 13:33 UTC (permalink / raw)
To: Anton Vorontsov; +Cc: Scott Wood, linuxppc-dev, Li Yang
On Mar 19, 2009, at 1:01 PM, Anton Vorontsov wrote:
> Currently it doesn't matter where the mdio nodes are placed, but with
> power management support (i.e. when sleep = <> properties will take
> effect), mdio nodes placement will become important: mdio controller
> is a part of the ethernet block, so the mdio nodes should be placed
> correctly. Otherwise we may wrongly assume that MDIO controllers are
> available during sleep.
>
> Suggested-by: Scott Wood <scottwood@freescale.com>
> Suggested-by: Kumar Gala <galak@kernel.crashing.org>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/ksi8560.dts | 79 ++++++-----
> arch/powerpc/boot/dts/mpc8536ds.dts | 78 ++++++-----
> arch/powerpc/boot/dts/mpc8540ads.dts | 117 ++++++++
> +--------
> arch/powerpc/boot/dts/mpc8541cds.dts | 78 ++++++-----
> arch/powerpc/boot/dts/mpc8544ds.dts | 81 ++++++------
> arch/powerpc/boot/dts/mpc8548cds.dts | 156 +++++++++++
> +----------
> arch/powerpc/boot/dts/mpc8555cds.dts | 78 ++++++-----
> arch/powerpc/boot/dts/mpc8560ads.dts | 102 ++++++++-------
> arch/powerpc/boot/dts/mpc8568mds.dts | 102 ++++++++-------
> arch/powerpc/boot/dts/mpc8572ds.dts | 150 +++++++++++
> +----------
> arch/powerpc/boot/dts/mpc8572ds_36b.dts | 150 +++++++++++
> +----------
> arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts | 39 +++---
> arch/powerpc/boot/dts/sbc8548.dts | 78 ++++++-----
> arch/powerpc/boot/dts/sbc8560.dts | 100 ++++++++-------
> arch/powerpc/boot/dts/stx_gp3_8560.dts | 78 ++++++-----
> arch/powerpc/boot/dts/tqm8540.dts | 117 ++++++++
> +--------
> arch/powerpc/boot/dts/tqm8541.dts | 90 +++++++------
> arch/powerpc/boot/dts/tqm8548-bigflash.dts | 168 ++++++++++++
> +-----------
> arch/powerpc/boot/dts/tqm8548.dts | 168 ++++++++++++
> +-----------
> arch/powerpc/boot/dts/tqm8555.dts | 90 +++++++------
> arch/powerpc/boot/dts/tqm8560.dts | 90 +++++++------
> arch/powerpc/platforms/85xx/ksi8560.c | 1 +
> arch/powerpc/platforms/85xx/mpc8536_ds.c | 1 +
> arch/powerpc/platforms/85xx/mpc85xx_ads.c | 1 +
> arch/powerpc/platforms/85xx/mpc85xx_cds.c | 1 +
> arch/powerpc/platforms/85xx/mpc85xx_ds.c | 1 +
> arch/powerpc/platforms/85xx/mpc85xx_mds.c | 1 +
> arch/powerpc/platforms/85xx/sbc8548.c | 1 +
> arch/powerpc/platforms/85xx/sbc8560.c | 1 +
> arch/powerpc/platforms/85xx/stx_gp3.c | 1 +
> arch/powerpc/platforms/85xx/tqm85xx.c | 1 +
> 31 files changed, 1183 insertions(+), 1016 deletions(-)
applied to next
- k
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH 4/4] powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
2009-03-19 18:01 ` [PATCH 4/4] powerpc/86xx: " Anton Vorontsov
2009-03-20 9:38 ` Martyn Welch
@ 2009-03-24 13:33 ` Kumar Gala
1 sibling, 0 replies; 10+ messages in thread
From: Kumar Gala @ 2009-03-24 13:33 UTC (permalink / raw)
To: Anton Vorontsov; +Cc: Scott Wood, linuxppc-dev, Li Yang
On Mar 19, 2009, at 1:01 PM, Anton Vorontsov wrote:
> Currently it doesn't matter where the mdio nodes are placed, but with
> power management support (i.e. when sleep = <> properties will take
> effect), mdio nodes placement will become important: mdio controller
> is a part of the ethernet block, so the mdio nodes should be placed
> correctly. Otherwise we may wrongly assume that MDIO controllers are
> available during sleep.
>
> Suggested-by: Scott Wood <scottwood@freescale.com>
> Suggested-by: Kumar Gala <galak@kernel.crashing.org>
> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
> ---
> arch/powerpc/boot/dts/gef_ppc9a.dts | 39 ++++---
> arch/powerpc/boot/dts/gef_sbc310.dts | 39 ++++---
> arch/powerpc/boot/dts/gef_sbc610.dts | 39 ++++---
> arch/powerpc/boot/dts/mpc8641_hpcn.dts | 157 ++++++++++++++
> +-------------
> arch/powerpc/boot/dts/sbc8641d.dts | 156 ++++++++++++++
> +-------------
> arch/powerpc/platforms/86xx/gef_ppc9a.c | 1 +
> arch/powerpc/platforms/86xx/gef_sbc310.c | 1 +
> arch/powerpc/platforms/86xx/gef_sbc610.c | 1 +
> arch/powerpc/platforms/86xx/mpc8610_hpcd.c | 1 +
> arch/powerpc/platforms/86xx/mpc86xx_hpcn.c | 1 +
> arch/powerpc/platforms/86xx/sbc8641d.c | 1 +
> 11 files changed, 237 insertions(+), 199 deletions(-)
applied to next
- k
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2009-03-24 13:33 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-03-19 18:00 [PATCH v4 0/4] Some PM-related patches for galak/powerpc.git next Anton Vorontsov
2009-03-19 18:01 ` [PATCH 1/4] powerpc/83xx: Add power management support for MPC837x boards Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 2/4] powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 3/4] powerpc/85xx: " Anton Vorontsov
2009-03-24 13:33 ` Kumar Gala
2009-03-19 18:01 ` [PATCH 4/4] powerpc/86xx: " Anton Vorontsov
2009-03-20 9:38 ` Martyn Welch
2009-03-24 13:33 ` Kumar Gala
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).